12 93 14 Bicycle Storage Lockers.pdf

589-707 | Construct Addition & Renovate Building 3 for Pharmacy and Associated Parking

Robert J. Dole VAMC – Wichita, KS 100% Bid Set – Addendum 01

12 93 14 - 1

BICYCLE STORAGE LOCKERS

SECTION 12 93 14

PART 1 GENERAL

1.1 SECTION INCLUDES

A. Metal bicycle storage lockers

1.2 RELATED SECTIONS

A. Section 03 30 00 - Cast-in-Place Concrete: For concrete mounting pads.

1.3 REFERENCES

A. ASTM A314 - Standard Specification for Stainless Steel Billets and Bars for

Forging.

B. ASTM A591 - Standard Specification for Steel Sheet, Electolytic Zinc Coated, for Light Coating Mass Applications.

C. ASTM B221 - Standard Specification for Aluminum and Aluminum-Alloy Extruded

Bars, Rods, Wire, Profiles and Tubes.

1.4 SUBMITTALS

A. Submit under provisions of Section 01 30 00.

B. Product Data: Manufacturer's data sheets on each product to be used, including:

1. Preparation instructions and recommendations.

2. Storage and handling requirements and recommendations.

3. Installation methods.

C. Shop Drawings: Show assembly and installation details. Include physical characteristics such as shape, dimensions, bicycle parking capacity and finish.

D. Selection Samples: For each finish product specified, two complete sets of color chips representing manufacturer's full range of available colors and patterns.

E. Verification Samples: For each finish product specified, two samples, minimum size 2 inches (52 mm) square, representing actual product, color and patterns.

F. Maintenance Data: Include recommended methods for repairing damage to the powder coat finish.

1 08/22/2025

12 93 14 - 2

1.5 QUALITY ASSURANCE

A. Manufacturer Qualifications: A firm experienced in manufacturing site furnishing products similar to those required for this project and with a record of successful in-service performance.

B. Installer Qualifications: A licensed and experienced installer who has completed installation of bicycle lockers similar in material, design and extent to that indicated for this project and whose work has resulted in construction with a record of successful in-service performance.

C. Source Limitations: Obtain each color, finish and type of bicycle locker from a single source with resources to provide components of consistent quality in appearance and physical properties.

D. Product Options: Drawings indicate size, shape and dimensional requirements of bicycle lockers and are based on the specific system indicated.

E. Mock-Up: Provide a mock-up for evaluation of materials and application workmanship.

1. Install in areas designated by Architect.

2. Do not proceed with remaining work until workmanship is approved by

Architect.

3. Refinish mock-up installation as required to produce acceptable work.

1.6 DELIVERY, STORAGE, AND HANDLING

A. Deliver materials to the site in an undamaged condition. Carefully store materials to provide proper protection against damage from moisture, heat, cold, direct sunlight or other causes.

B. Store products in manufacturer's unopened packaging until ready for installation.

C. Store and dispose of solvent-based materials, and materials used with solvent-based materials, in accordance with requirements of local authorities having jurisdiction.

1.7 PROJECT CONDITIONS

12 93 14 - 3

A. Anticipate environmental conditions (temperature, humidity and ventilation) to schedule work within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's absolute limits.

1.8 WARRANTY

A. Provide manufacturer’s limited one year warranty.

PART 2 PRODUCTS

2.1 MANUFACTURERS

A. Basis of Design Manufacturer: Dura Bike Locker® Co.; 3790 Bradview Drive, Sacramento, CA 95827. ASD. Toll Free Tel: (800) 722-2453. Tel: (916) 363-

7225. Fax: (916) 363-0225. Email: info@durabikelocker.com Web:

http://www.durabikelocker.com

2.2 BICYCLE STORAGE

A. Bicycle Lockers: Dura Bike Locker® material G-90 galvanized steel bicycle locker as manufactured by Hannan Specialties, Inc.

1. Dimensions: 39 inches wide by 48 inches high by 75 inches long (990.6 mm x 1219.2 mm x 1905.0 mm).

2. Provide single bike units model DLP ‘Pie Shaped’ Lockers as indicated on the drawings. Note: Fixed back panel, Item #1 (as required) replaces rear door and its associated components.

B. Bicycle Lockers: Dura Bike Locker® material G-90 galvanized model DLP ‘Pie

Shaped’ steel bicycle locker as manufactured by Hannan Specialties, Inc.

1. Dimensions: 39 inches wide by 48 inches high by 75 inches long (front tapers to 9" at the rear x 48" high (990.6 mm x 1219.2 mm x 1905.0 mm).

2. Provide multiple units as indicated on the drawings.

C. Galvanized Steel Fabrication:

1. Exterior Walls, Tops, Back Panels and Doors (ASTM A591): 16 gauge

(1.613 mm) galvanized steel. Doors shall have a 16 gauge (1.613 mm) galvanized steel horizontal stiffener for additional rigidity.

2. Frames (ASTM A591): 14 gauge (1.897 mm) CRS. All frame panels shall have 6 punched-in louvered vents.

12 93 14 - 4

3. U-Lock Box: Shall have a lock mechanism capable of accommodating a ‘U’ style lock or cable/chain lock for additional security. (U-locks, cables, and/or chains not provided).

4. Divider Panels (ASTM A591): 18 gauge (1.311 mm) galvanized steel.

5. Gear Hooks: Provide interior hangers for riding gear, zinc coated steel

“rope hook”.

6. Perforations: Provide perforated doors, walls, and DLP ‘Pie Shaped’ back nose.

7. Full length door hinge (ASTM A314): 16 gauge (1.613 mm) stainless steel.

8. 3-Point Locking bar Mechanism (ASTM A314): 1 inch wide by 1/4 inch thick (25.4 mm by 6.4 mm) stainless steel flat bar running beyond the full length of the door frame and into the top, threshold, and jamb (3-

Points to insure Maximum Security).

9. Fasteners shall be zinc coated steel and shall be fastened from the inside.

10. Standard Finish: (TGIC) Powder Coated.

a. Color: As selected by Owner.

11. Stainless steel padlock style handle (padlock not included).

PART 3 EXECUTION

3.1 EXAMINATION

A. Do not begin installation until the location has been properly prepared.

B. If the location preparation is the responsibility of another installer notify the Architect of unsatisfactory preparation before proceeding.

3.2 PREPARATION

A. Clean the location thoroughly prior to the installation process. Prepare all surfaces using the methods recommended by the manufacturer for achieving the best result under the project conditions.

3.3 INSTALLATION

A. Install in accordance with the manufacturer's instructions.

B. Locate where shown on drawings. Assemble and anchor in accordance with the manufacturer's instructions.

12 93 14 - 5

C. Set Dura Bike Locker® bicycle lockers secured to construction, level and true to line, in correct relationship to adjacent structure and improvements.

3.4 PROTECTION

A. Protect installed products until completion of project.

B. Touch-up, repair, or replace damaged products before substantial completion.

END OF SECTION