ATTACHMENT L-Generator Cutsheet.pdf

MB600 | 18.1L | 600 kW

INDUSTRIAL BI-FUEL GENERATOR SET

EPA Compliant Stationary Emergency

SP

EC

S

HE

ET

SP

EC

S

HE

ET

Image used for illustration purposes only

Standby Power Rating 600 kW, 750 kVA, 60 Hz

Prime Power Rating* 540 kW, 675 kVA, 60 Hz

*EPA Certified Prime ratings are not available in the US or its Territories

Codes and Standards Not all codes and standards apply to all configurations. Contact factory for details.

UL2200, UL6200, UL1236, UL142

CSA C22.2, ULC S601, B149

BS5514 and DIN 6271

SAE J1349

NFPA 37, 70, 99, 110

NEC700, 701, 702, 708

ISO 3046, 7637, 8528, 9001

NEMA ICS10, MG1, 250, ICS6, AB1

ANSI C62.41

TM

Powering Ahead Generac Bi-Fuel™ generators start on diesel fuel and add natural gas as load is applied until the unit runs primarily on natural gas. Generac’s Bi-Fuel generators are fully integrated solutions, not aftermarket conversions in the field. That means every component is specifically designed, engineered and factory-validated to work together. Generac Bi-Fuel generators have the added benefit of being EPA-compliant from the factory.

RISK MITIGATION VIA FUEL REDUNDANCY

Because nobody can predict how long a power outage will last, many diesel-fueled standby power systems are sized for extended running times.

Nevertheless, onsite diesel fuel supplies are limited, and infrastructure damage could make refueling difficult. Generac Bi-Fuel generators make the most of an onsite diesel fuel supply by running primarily on natural gas. That means less onsite diesel fuel is required and running times will be greatly extended compared to diesel-only solutions. And because the natural gas infrastructure tends not to be affected by the same conditions that lead to power outages, fuel reliability is improved.

LOWER TOTAL COST OF OWNERSHIP

Because natural gas costs less than diesel, fuel costs are significantly reduced over the long term. And since less onsite diesel fuel is required for long running times, installation, operational and maintenance costs are reduced.

SCALABILITY AS PART OF A MODULAR POWER SYSTEM

Generac Bi-Fuel generators can be configured as part of a Modular Power System (MPS)—connected via integrated paralleling with other Generac generators. This makes the system scalable, meaning there is no need to install more power than you need.

CODE COMPLIANCE

Generac Bi-Fuel generators meet the onsite fuel requirements for emergency systems as referenced in NEC700 and NFPA 110. Less onsite diesel fuel means easier permitting. And indoor fuel installations with capacity limits per NFPA or local codes become a viable option.

EPA Compliant Stationary Emergency

SP

EC

S

HE

ET

SP

EC

S

HE

ET

CONTROL SYSTEM

Digital G-200 Paralleling Panel-Touchscreen

Program Functions

• Programmable Crank Limiter

• 7-Day Programmable Exerciser

• Special Applications Programmable Logic Controller

• RS-232/485 Communications

• All Phase Sensing Digital Voltage Regulator

• 2-Wire Start Capability

• Date/Time Fault History (Event Log)

• Isochronous Governor Control

• Waterproof/Sealed Connectors

• Audible Alarms and Shutdowns

• Not in Auto (Flashing Light)

• Auto/Off/Manual Switch

• E-Stop (Red Mushroom-Type)

• NFPA110 Level I and II (Programmable)

• Customizable Alarms, Warnings, and Events

• Modbus® Protocol

• Predictive Maintenance Algorithm

• Sealed Boards

• Password Parameter Adjustment Protection

• Single Point Ground

• 16 Channel Remote Trending

• 0.2 msec High Speed Remote Trending

• Alarm Information Automatically Annunciated on the

Display

Full System Status Display

• Power Output (kW)

• Power Factor

• kW Hours, Total and Last Run

• Real/Reactive/Apparent Power

• All Phase AC Voltage

• All Phase Currents

• Oil Pressure

• Coolant Temperature

• Coolant Level

• Engine Speed

• Battery Voltage

• Frequency

Alarms and Warnings

• Oil Pressure

• Coolant Temperature

• Coolant Level

• Low Fuel Pressure

• Engine Overspeed

• Battery Voltage

• Alarms and Warnings Time and Date Stamped

• Snap Shots of Key Operation Parameters During

Alarms and Warnings

• Alarms and Warnings Spelled Out (No Alarm Codes)

ENGINE SYSTEM

• Oil Drain Extension

• Air Cleaner

• Level 1 Fan and Belt Guards (Open Set Only)

• Stainless Steel Flexible Exhaust Connection

• Critical Silencer (Enclosed Units Only)

• Factory Filled Oil and Coolant

FUEL SYSTEM

• Primary and Secondary Fuel Shutoff

• Primary and Secondary Fuel Filters

COOLING SYSTEM

• Closed Coolant Recovery System

• UV/Ozone Resistant Hoses

• Factory-Installed Radiator

• 50/50 Ethylene Glycol Antifreeze

ELECTRICAL SYSTEM

• Battery Charging Alternator

• Battery Cables

• Battery Tray

• Rubber-Booted Engine Electrical Connections

• Solenoid Activated Starter Motor

ALTERNATOR SYSTEM

• Class H Insulation Material

• 2/3 Pitch

• Skewed Stator

• Permanent Magnet Excitation

• Amortisseur Winding

• Sealed Bearing

• Full Load Capacity Alternator

GENERATOR SET

• Internal Genset Vibration Isolation

• Separation of Circuits - High/Low Voltage

• Separation of Circuits - Multiple Breakers

• Wrapped Exhaust Piping (Enclosed Units Only)

• Standard Factory Testing

• 2 Year Limited Warranty (Standby Rated Units)

• 1 Year Limited Warranty (Prime Rated Units)

• Silencer Mounted on the Discharge Hood

(Enclosed Units Only)

ENCLOSURE (If Selected)

• Rust-Proof Fasteners with Nylon Washers to Protect Finish

• High Performance Sound-Absorbing Material (Sound Attenuated Enclosure)

• Gasketed Doors

• Upward Facing Discharge Hoods (Radiator and Exhaust)

• Stainless Steel Lift Off Door Hinges

• Stainless Steel Lockable Handles

• RhinoCoat™ - Textured Polyester Powder Coat Paint

FUEL TANKS (If Selected)

• UL 142/ULC S-601

• Double Wall

• Vents

• Sloped Top

• Sloped Bottom

• Factory Pressure Tested (2 psi)

• Rupture Basin Alarm

• Fuel Level

• Check Valve in Supply and Return Lines

• RhinoCoat™ - Textured Polyester Powder Coat Paint

• Stainless Hardware

STANDARD FEATURES

PARALLELING CONTROLS

• Auto-Synchronization Process

• Isochronous Load Sharing

• Reverse Power Protection

• Maximum Power Protection

• Electrically Operated, Mechanically Held Paralleling

Switch

• Sync Check System

• Independent On Board Paralleling

• Shunt Trip and Auxiliary Contact

EPA Compliant Stationary Emergency

SP

EC

S

HE

ET

SP

EC

S

HE

ET

CONFIGURABLE OPTIONS

ENGINE SYSTEM

○ Air Filter Restriction Indicator

○ Radiator Stone Guard (Open Set Only)

○ Engine Coolant Heater

○ Level 1 Fan and and Belt Guards (Enclosed Units Only)

○ Oil Heater

○ Shipped Loose Critical Silencer (Open Set Only)

FUEL SYSTEM

○ NPT Flexible Fuel Line

ELECTRICAL SYSTEM

○ 10A UL Listed Battery Charger

○ Battery Warmer

ALTERNATOR SYSTEM

○ Alternator Upsizing

○ Anti-Condensation Heater

CIRCUIT BREAKER OPTIONS

○ Main Line Circuit Breaker

○ Electronic Trip Breakers

GENERATOR SET

○ Extended Factory Testing

○ IBC Seismic Certification

○ 12 Position Load Center

ENCLOSURE

○ Weather Protected Enclosure

○ Level 1 Sound Attenuated

○ Level 2 Sound Attenuated

○ Level 2 Sound Attenuated with Motorized Dampers

○ Steel Enclosure

○ Aluminum Enclosure

○ Up to 200 MPH Wind Load Rating (Contact Factory for Availability)

○ AC/DC Enclosure Lighting Kit

○ Enclosure Heater (with Motorized Dampers Only)

CONTROL SYSTEM

○ NFPA 110 Compliant 21-Light Remote Annunciator

○ Remote Relay Assembly (8 or 16)

○ Oil Temperature Indication and Alarm

○ Remote E-Stop (Break Glass-Type, Surface Mount)

○ Remote E-Stop (Red Mushroom-Type, Surface Mount)

○ Remote E-Stop (Red Mushroom-Type, Flush Mount)

○ 10A Engine Run Relay

○ Ground Fault Annunciator

○ Programmable Logic Full Auto Back-Up Control (PLS) for PM-SC

○ 100 dB Alarm Horn

○ 120V GFCI and 240V Outlets

○ Damper Alarm Contacts (with Motorized Dampers Only)

WARRANTY (Standby Gensets Only)

○ 2 Year Extended Limited Warranty

○ 5 Year Limited Warranty

○ 5 Year Extended Limited Warranty

○ 7 Year Extended Limited Warranty

○ 10 Year Extended Limited Warranty

ENGINEERED OPTIONS

ENGINE SYSTEM

○ Fluid Containment Pan

ALTERNATOR SYSTEM

○ 2nd Breaker Systems

CONTROL SYSTEM

○ Battery Disconnect Switch

GENERATOR SET

○ Special Testing

FUEL TANKS

○ Overfill Protection Valve

○ UL 2085 Tank

○ Stainless Steel Tank

○ Special Fuel Tanks (MIDEQ and FL DEP/DERM, etc)

○ Vent Extensions

EPA Compliant Stationary Emergency

SP

EC

S

HE

ET

SP

EC

S

HE

ET

General

Make Perkins

EPA Emissions Compliance Stationary Emergency

EPA Emissions Reference See Emission Data Sheet

Cylinder # 6

Type In-Line

Displacement - In3 (L) 1,106.36 (18.13)

Bore - in (mm) 5.71 (145)

Stroke - in (mm) 7.20 (183)

Compression Ratio 14.5:1

Intake Air Method Turbocharged/Aftercooled

Cylinder Head Type 4-Valve

Piston Type Aluminum

Crankshaft Type I-Beam Section

Engine Governing

Governor Electronic Isochronous

Frequency Regulation (Steady State) ±0.25%

Lubrication System

Oil Pump Type Gear

Oil Filter Type Full Flow

Crankcase Capacity - qt (L) 47.55 (45)

Cooling System

Cooling System Type Centrifugal

Fan Type Pusher

Fan Speed - RPM 1,439

Fan Diameter - in (mm) 38 (965)

Fuel System

Fuel Type Ultra Low Sulfur Diesel #2

Carburetor ASTM

Fuel Filtering (Microns) Primary 10 - Secondary 2

Fuel Inject Pump Make Electronic

Injector Type MEUI

Engine Type Pre-Combustion

Fuel Supply Line - in (mm) 0.5 (12.7) NPT

Fuel Return Line - in (mm) 0.5 (12.7) NPT

Required Natural Gas Pressure- psi (kPa) 1 (7)

Maximum Required Volume of Natural Gas Needed - cfm (m3/min)

50 (15)

Engine Electrical System

System Voltage 24 VDC

Battery Charger Alternator Standard

Battery Size See Battery Index 0161970SBY

Battery Voltage (2) - 12 VDC

Ground Polarity Negative

APPLICATION AND ENGINEERING DATA

ENGINE SPECIFICATIONS

ALTERNATOR SPECIFICATIONS

Standard Model K0792124Y23

Poles 4

Field Type Revolving

Insulation Class - Rotor H

Insulation Class - Stator H

Total Harmonic Distortion <3%

Telephone Interference Factor (TIF) <50

Standard Excitation Permanent Magnet

Bearings Single Sealed Cartridge

Coupling Direct via Flexible Disc

Prototype Short Circuit Test Yes

Voltage Regulator Type Digital

Number of Sensed Phases All

Regulation Accuracy (Steady State) ±0.25%

EPA Compliant Stationary Emergency

SP

EC

S

HE

ET

SP

EC

S

HE

ET

OPERATING DATA

** Refer to “Emissions Data Sheet” for maximum bHP for EPA and SCAQMD permitting purposes.

Deration – Operational characteristics consider maximum ambient conditions. Derate factors may apply under atypical site conditions.

Please contact a Generac Power Systems Industrial Dealer for additional details. All performance ratings in accordance with ISO3046, BS5514, ISO8528, and DIN6271 standards.

Standby - See Bulletin 0187500SSB Prime - See Bulletin 0187510SSB

POWER RATINGS

Standby

Three-Phase 277/480 VAC @0.8pf 600 kW Amps: 902

Three-Phase 346/600 VAC @0.8pf 600 kW Amps: 722

MOTOR STARTING CAPABILITIES (skVA) skVA vs. Voltage Dip

277/480 VAC 30%

K0792124Y23 2,250

K0832124Y23 2,800

FUEL CONSUMPTION RATES*

Diesel – gph (Lph)

Fuel Pump Lift - ft (m) Percent Load Standby

12 (3.7) 25% 18.4 (69.7)

50% 28.2 (88.7)

Total Fuel Pump Flow (Combustion + Return) gph (Lph) 75% 35.6 (124.8)

121 (457) 100% 41.4 (156.7)

* Fuel supply installation must accommodate fuel consumption rates at 100% load.

** Natural Gas substitution may vary based on the application and load conditions Please consult factory for additional details on fuel consumption

COOLING

Standby

Coolant Flow gpm (Lpm) 114.1 (432)

Coolant System Capacity gal (L) 15.5 (58.6)

Heat Rejection to Coolant BTU/hr (kW) 1,589,760 (466)

Inlet Air cfm (m3/min) 30,088 (852)

Maximum Operating Ambient Temperature °F (°C) 122 (50)

Maximum Operating Ambient Temperature (Before Derate) See Bulletin No. 0199270SSD

Maximum Additional Radiator Backpressure in H2O (kPa) 0.5 (0.12)

COMBUSTION AIR REQUIREMENTS

Standby

Flow at Rated Power - cfm (m3/min) 1,836 (52)

ENGINE EXHAUST

Standby Standby

Rated Engine Speed RPM 1,800 Exhaust Flow (Rated Output) cfm (m3/min) 5,085 (144)

Horsepower at Rated kW** hp 909 Maximum Allowable Backpressure inHg (kPa) 2.13 (6.9)

Piston Speed ft/min (m/min) 2,161 (658.7) Exhaust Temperature (Rated Output - Post Silencer) °F (°C) 1,155 (624)

BMEP psi (kPa) 361 (2,489)

EPA Compliant Stationary Emergency

SP

EC

S

HE

ET

SP

EC

S

HE

ET

DIMENSIONS AND WEIGHTS*

YOUR FACTORY RECOGNIZED GENERAC INDUSTRIAL DEALER

Specification characteristics may change without notice. Dimensions and weights are for preliminary purposes only. Please contact a Generac Power Systems Industrial Dealer for detailed installation drawings.

* All measurements are approximate and for estimation purposes only.

Part No 10000006997 Rev. E 10/19/2020

Generac Power Systems, Inc. | P.O.Box 8 | Waukesha, WI 53189 P: (262) 544-4811 ©2020 Generac Power Systems, Inc. All rights reserved. All specifications are subject to change without notice.

OPEN SET

Run Time

- Hours

Usable Capacity

- Gal (L)

L x W x H - in (mm) Weight - lbs (kg)

No Tank - 154.4 (3,923) x 71.0 (1,803) x 67.3 (1,709) 8,662 - 10,922 (3,929 - 4,954)

8 334 158.5 (4,025) x 71.0 (1,803) x 81.3 (2,065) 10,337 - 12,597 (4,689 - 5,714)

24 1,001 158.5 (4,025) x 71.0 (1,803) x 103.3 (2,623) 11,262 - 13,522 (5,108 - 6,133)

24 1,001 228.0 (5,791) x 71.0 (1,803) x 92.3 (2,344) 11,812 - 14,072 (5,358 - 6,383)

48 2,002 290.0 (7,366) x 71.0 (1,803) x 103.3 (2,623) 13,512 - 15,772 (6,129 - 7,154)

WEATHER PROTECTED ENCLOSURE

Run Time

- Hours

Usable Capacity

- Gal (L)

L x W x H - in (mm) Weight - lbs (kg) Enclosure Only

Steel Aluminum

No Tank - 207.4 (5,268) x 70.9 (1,800) x 79.9 (2,031) 12,672 (5,748) 11,585 (5,748)

8 334 207.4 (5,268) x 70.9 (1,800) x 93.9 (2,387) 14,347 (6,508) 13,260 (6,015)

24 1,001 207.4 (5,268) x 70.9 (1,800) x 115.9 (2,945) 15,272 (6,927) 14,185 (6,434)

24 1,001 228.0 (5,791) x 70.9 (1,800) x 104.9 (2,666) 15,822 (7,177) 14,735 (6,684)

48 2,002 290.0 (7,366) x 70.9 (1,800) x 115.9 (2,945) 17,522 (7,948) 16,435 (7,455)

LEVEL 1 SOUND ATTENUATED ENCLOSURE

Run Time

- Hours

Usable Capacity

- Gal (L)

L x W x H - in (mm) Weight - lbs (kg)

Steel Aluminum

No Tank - 247.5 (6,285) x 70.9 (1,800) x 80.0 (2,032)

3,472 (1,575) 1,812 (822)

8 334 247.5 (6,285) x 70.9 (1,800) x 94.0 (2,388)

24 1,001 247.5 (6,285) x 70.9 (1,800) x 116.0 (2,946)

24 1,001 247.5 (6,285) x 70.9 (1,800) x 105.0 (2,667)

48 2,002 290.0 (7,366) x 70.9 (1,800)x 116.0 (2,946)

LEVEL 2 SOUND ATTENUATED ENCLOSURE

Run Time

- Hours

Usable Capacity

- Gal (L)

L x W x H - in (mm) Weight - lbs (kg)

Steel Aluminum

No Tank - 207.4 (5,268) x 70.9 (1,800) x 114.1 (2,899)

8 334 207.4 (5,268) x 70.9 (1,800) x 128.1 (3,255)

24 1,001 207.4 (5,268) x 70.9 (1,800) x 150.1 (3,813) 3,809 (1,728) 1,958 (888)

24 1,001 228.0 (5,791) x 70.9 (1,800) x 139.1 (3,534)

48 2,002 290.0 (7,366) x 70.9 (1,800) x 150.1 (3,813)

W

H

W

H

L

L

H

W

L

L W

H