3. FT3 Production Follow-On CDRL Package 24 Apr 2026.docx

Contract Data Requirements List (CDRL) Program: FT3 Production Follow-On Date: 24 April 2026 Version: 1 Date of Determination: (Contract Award Date unless otherwise specified on the CDRL)

1. Introduction This document was developed in accordance with DOD MIL-STD 31000C and DODM 5010.12 Acquisition and Management of Contractor-Prepared Data. This represents the general requirements for the Technical Data Package (TDP) for this program.

The purpose of this Attachment, Technical Data Package, is to define the data deliverables due for this program, including the instructions for their development, and delivery. All specific delivery instructions are specified on the CDRL forms or its digital (word, excel, pdf) equivalent.

2. General Guidelines The CDRL form, Department of Defense (DD) Form 1423, specifies the data required to be delivered to the Government, as well as the frequency and approval requirements. The Data Item Descriptions (DIDs), listed on the CDRL form, were selected from the Acquisition Streamlining and Standardization Information System (ASSIST) and provide additional direction for data preparation.

3. Communications Any correspondence related to requests for data delivery deviations and/or amendments, additions or deletions to the CDRL form shall be addressed to the Procuring Contracting Officer (PCO) with a courtesy copy to the Data Management Officer (DMO) (Air Force Nuclear Weapons Center (AFNWC)/NIMED) and the cognizant Program Manager (PM). Copies of all forms and templates noted in this file are available as requested from PM, DMO, or PCO.

4. Codes used in the DD Form 1423 All CDRLs require Government approval. The directions for submittal and approval of data are indicated in Blocks 7, 8, 9, 10, 11, 12, 13, 14, 15, and 16 of the DD Form 1423. Usually, the direction is in the form of a code (explained below). The following abbreviations/codes are common usage within AFNWC.

4.1 Block 7, DD Form 250 Requirements

Block 7 of the CDRL form indicates whether Procurement Quality Assurance (PQA) inspections and acceptance of deliverable data by DD Form 250 is required. “Draft” copies submitted for advance approval and “Preliminary Draft” copies submitted are exempt from the DD Form 250 requirements. Information copies of DD Form 250 to accompany each letter of transmittal for this category of data.

4.2 Block 8, Approval Code (for PRE-Approval items)

When items of critical data requiring specific advanced approval or draft is required before distribution of final data item should be identified as (code “A”), the approval authority (ORG) for that 1423 is designated in Block 14. When document pre-approval or draft is not required (code “N/A”). When the data item requires submission of a draft document prior to publication of a final document, block 16 of the DD Form 1423 shall show the length of time required for Government approval and/or disapproval and subsequent turn-around time for the contractor to resubmit the data after Government approval and/or disapproval has been issued.

4.3 Block 10, Frequency of Submittals

* When ASREQD is used in Blocks 10, 11, 12 or 13 an explanation of the requirements must be entered in Block 16.

4.4 Block 11, 12 and 13, Dates of As of, Initial and Subsequent Submissions

ASREQ

or

ASREQD

As required*

* When ASREQD is used in Blocks 10, 11, 12 or 13 an explanation of the requirements must be entered in Block 16.

Indicate SEE BLK 16 if submission requirements are listed in Block 16.

5. Supplemental Data Preparation Instructions:

5.1 Data Item Description (DID) Version

The most current version of the DID at the time of the award of the contract or Task Order, whichever date is most current, specified in Block 4, is to be used when submitting data. The most current version can be found at http://quicksearch.dla.mil/.

5.2 DID Tailoring

The DID is a specification for the preparation of data. A DID may only be tailored down, never added to. DID tailoring is reflected in Block 16 of the CDRL form. “T” entered after the DID number in Block 4, means that the DID has been tailored. Block 4 tailoring is made to either relax preparation instructions or to tailor the DID to be in consonance with the source document tailoring contained in the Statement of Work (SOW), Performance Work Statement (PWS) or Contractor Statement of Work (CSOW).

5.3 Scientific and Technical Information (STINFO) Distribution Statement Markings The designation in Block 9 of the CDRL form indicates that one of the following six (6) authorized distribution statements from Department of Defense Instruction (DoDI) 5230.24 and Department of the Air Force Instruction (DAFI) 61-201 shall be annotated on that technical data. Distribution statements will be selected to denote the audience for which the data is intended. A distribution statement marking is distinct from and in addition to a security classification marking assigned in accordance with (IAW) DoDM5200.01V2_AFMAN16-1404V2 Information Security Program: Marking of Classified Information. Should Block 9 of the CDRL form and the DID be in conflict, Block 9 of the CDRL form shall take precedence. The following distribution statements are authorized for use in marking of all documents:

Distribution Statement A:

Approved for public release. Distribution is unlimited.

Distribution Statement B:

Distribution authorized to U.S. Government Agencies (category), (date of determination). Other requests for this document must be referred to MMIII SPO (AFNWC/NIM), 6014 Dogwood Ave, Hill AFB UT 84056

Distribution Statement C:

Distribution authorized to U.S. Government Agencies and their contractors (category), (date of determination). Other requests for this document must be referred to MMIII SPO (AFNWC/NIM), 6014 Dogwood Ave, Hill AFB UT 84056.

Distribution Statement D:

Distribution authorized to Department of Defense and U.S. DoD contractors only (category), (date of determination). Other requests must be referred to MMIII SPO (AFNWC/NIM), 6014 Dogwood Ave, Hill AFB UT 84056.

Distribution Statement E:

Distribution authorized to DoD Components only (category), (date determination). Other requests must be referred to MMIII SPO (AFNWC/NIM), 6014 Dogwood Ave, Hill AFB UT 84056.

Distribution Statement F:

Further dissemination only as directed by MMIII SPO (AFNWC/NIM), 6014 Dogwood Ave, Hill AFB UT 84056 (date of determination) or higher DOD authority.

5.4 Other Notices

All technical documents marked with Distribution Statements B, C, D, E, or F will also be marked with the following notices:

Export Control Warning Statement:

This document contains technical data whose export is restricted by the Arms Export Control Act (Section 2751 of Title 22, United States Code) or the Export Control Reform Act of 2018 (Chapter 58 Sections 4801-4852 of Title 50, United States Code). Violations of these export laws are subject to severe criminal penalties. Disseminate in accordance with provisions of DoD Directive 5230.25 and DoD Instruction 2040.02.

When the data is export controlled, include Export Control as one of the reasons IAW DoDI 5230.24 Section 3. Paragraph 3.4.i.

DoDD 5230.25 is available online at https://www.esd.whs.mil/DD/.

NOTE: The CDO Program Manager (PM) may remove the “Export Control Warning” if “critical technology” is not a reason annotated in the distribution statement and if the CDO PM can verify the technical report/document is not export control.

Note – When distributing export-controlled data, include the “Notice to Accompany…” IAW DoDD 5230.25 Enclosure 5, by paper copy or read-me-file.

Destruction Notice:

(destruction notices are now optional on Scientific/Technical information documents.)

Documents designated as Distribution B, C, D, E, or F shall be marked with one of the following statements:

For classified documents:

DESTRUCTION NOTICE: Follow the procedures in National Industrial Security Program Operating Manual (NISPOM) Title 32 § 117.15(g) and Title 32 § 2001.47, DoDM5200.01V3_DAFMAN16-1404V3 Information Security Program: Protection of Classified Information, Enclosure 3, Paragraph 17.

For unclassified, limited documents: (destruction notices are now optional on Scientific/Technical information documents.

DESTRUCTION NOTICE: Record and non-record copies of CUI documents will be disposed of IAW Chapter 33 of Title 44, U.S.C. and the DoD Components’ records management directives. When destroying CUI, including in electronic form, agencies must do so in a manner making it unreadable, indecipherable, and irrecoverable.

Controlled Unclassified Information (CUI) Markings IAW DoDI5200.48_DAFI16-1403, Controlled Unclassified Information, mark all applicable documents with the appropriate CUI markings and CUI designation indicator block. Place the CUI designation indicator block at the bottom-right side of the first page or cover page when using the Limited Dissemination Control (LDC) marking and if using a distribution statement place CUI designation indicator block above the distribution statement Note - CUI marking requirements do not affect STINFO requirements, All CUI documents determined to warrant the use of a distribution statement must contain Controlled Technical Information (CTI).

5.5 Pricing CDRL Items Separately

If blocks 17 and 18 of the DD form 1423 documents are marked as "N/A" and "NSP" respectively, then the Government does not want to separately group or price CDRL items. If blocks 17 and 18 are left blank, the Government intends to seek separate pricing for the development costs of each CDRL. This pricing is for development costs of the data items and is considered separate from data rights costs.

6. Supplemental Data Delivery Instructions:

6.1 Due Dates

Due dates for delivery of data are to be construed as receipt at destination. Due dates are based on calendar days unless otherwise noted. If due date falls on a non-business day, i.e. weekend or holiday, due date is pushed to the next business day.

6.2 Late Delivery

Delivery of data is considered late if it does not arrive at its destination by 1530 hours (3:30 PM) Mountain Time on the date specified in Blocks 12, 13, or 16 of the CDRL.

6.3 Submittal Procedures:

6.3.1 CDRL Submittal Procedure

For the purposes of data submittal, unclassified CDRLs are submitted to the government via TopVue https://icbm.topvue.com/topvue-icbm/. For access to CDRLvue, the contractor must obtain and maintain T-1 eligibility, National Agency Check with Inquiries (NACI).

THIS IS FOR UNCLASSIFIED CDRL SUBMITTALS ONLY.

(See below for Classified CDRL submittals (6.3.2)) Each data submittal shall be accompanied by a CDA form (please request current version from ORG1). If for any reason a CDA form is not available, a cover letter shall contain the following information:

1. Contract number

2. CDRL sequence number (e.g., A001)

3. Exact title and subtitle (if applicable) of the document being transmitted

4. Line item or CLIN number

5. Modification Number or Order Number

6. Document date, number, and revision information (if applicable)

7. Data delivery method and date of delivery

8. Whether the document is a draft or final submittal

9. For approval data: State “For Approval”

10. If the document is a re-submittal, reference the Government letter CDA requesting re-submittal or disapproval of previous submittal

11. For periodic reports: The report period that the document covers

12. Distribution: Information disclosing the total contractual distribution being made per Block 14 or Block 16 of the CDRL Form

6.3.2 Classified CDRL Submittal Procedure

If any deliverables contain classified information, contractor must obtain and maintain T-3 eligibility, National Agency Check with Law and Credit (NACLC). Classified CDRLs and classified documentation are submitted IAW this instruction and are never to be emailed.* Classified CDRLs or portions of a CDRL, as applicable, shall be forwarded IAW Appendix B of the DD254 and 32 CFR Part 117, National Industrial Security Program Operating Manual (NISPOM). For Classified Disks send two (2) copies.

Outer Envelope:

Address ATTN: AFNWC/NIMS MMIII Security Office

Inner Envelope:

Address ATTN: Name of person for whom the document should be delivered

*A letter of delivery shall be submitted to TopVue https://icbm.topvue.com/topvue-icbm/csswb/login , when classified data is delivered via the instructions above.

7. Supplemental Data Review and Approval Process:

7.1 CDRL Approvals

Government must approve/disposition each data item. In addition, Block 16 of the form may contain additional directions. Types of dispositioning that occur are as follows:

Approved with Comment or Disapproved The Contractor shall revise data items “Approved with Comments or Disapproved” IAW the specific written comments transmitted with the CDA or PCO/DMO letter and resubmit not later than 30 calendar days (unless otherwise directed) from receipt of the “Approved with Comments or Disapproved”, unless otherwise directed. The resubmitted data will require a new approval cycle as indicated in Block 16 of the DD Form 1423.

Draft Versions of the CDRL If a DD Form 1423 directs the Contractor to submit a “draft” version of an approval CDRL in advance of the final version, the draft will be considered an information only submission. However, the PM/DMO still retains the right to disapprove a draft data item that does not comply with the contract requirements. Unless otherwise directed by the PCO, the Contractor shall incorporate the Government’s comments in the final submission and shall not resubmit the draft version of the data item.

7.2 Contractual Document Action (CDA)

After the Government receives a data item submission, a Temporary Data Identification (TDID) number, a unique identifier to that submission, will be assigned by the DMO. The Government’s review of that data item will result in a coordinated CDA form, or PCO letter, indicating the data item’s approval or disapproval. Should the Government have comments on the data item, the CDA will include either comments on the CDA form itself or a Comment Resolution Matrix (CRM). Comments will be provided to the submitter IAW the format and timeline noted in block 16. Comments will be assigned one of the following codes:

7.3 Information Only CDRLs

When an “A” is not indicated in Block 8 of the DD Form 1423, the PM/DMO still retains the right to disapprove any data that does not comply with contract requirements. The Contractor shall revise the disapproved data IAW with the specific written comments transmitted with the CDA form or PCO letter and resubmit not later than 30 calendar days, unless otherwise directed, from receipt of the disapproval. The resubmitted data will require a new approval cycle as indicated in Block 8 of the DD Form 1423.

8. Data Accession List (DAL) During performance of the contract, requests from the PCO for data ordered from the Data Accession List (DAL) (with the application of the current version, for DID DI-MGMT-81453) shall be provided at no increase in contract price. Requests for quantities greater than two each per document shall be honored upon receipt of PCO direction and with Contractor concurrence that such request can be filled at no increase in contract price.

9. Organizational Cross Reference List The following Organizational Cross Reference List shall be used in conjunction with the CDRLs to determine actual addressees for distribution of data. The ORG number will be entered in lieu of an address on the CDRL and will be a part of the CDRL package. Changes to the list will be identified by an asterisk next to the ORG number and a revision date to the list. Any changes to the Attention/To or Contract Info list will not require a contract mod.

ORG1/AFNWC/NIM

Hill AFB UT 84056

ORG2/AFNWC/NIM

Hill AFB UT 84056

ORG3/AFNWC/NIM

Hill AFB UT 84056

Hill AFB UT 84056

Hill AFB UT 84056

Hill AFB UT 84056

Hill AFB, UT 84056

Hill AFB UT 84056

Hill AFB UT 84056

Hill AFB UT 84056

Hill AFB UT 84056

10. CDRL Master Listing Index Comment by WELLS, TAMARA R CTR USAF AFMC AFNWC/NIMG: Discuss adding in the Production Status Report, DI-MGMT-81255 at 2.1.8

Full 1423’s for CDRL’s applicable to this program are included in section 11 of this document.

11. DD Form 1423s (full 1423’s) *1423’s, block A Reference Number: CLIN number to be added at time of award **1423’s block E Reference Number: Contract and Mod/TO number to be added at time of award ***1423’s block G & I will be signed at time of award ****1423’s Reference Blk G for status of CDRL package.

Prepared by Approved by

CONTRACT DATA REQUIREMENTS LIST

(1 Data Item)

Form Approved OMB No. 0704-0188

The public reporting burden for this collection of information is estimated to average 110 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to the Department of Defense, Executive Services and Communications Directorate (07040188). Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number.

Please do not return your form to the above organization. Send completed form to the Government Issuing Contracting Officer for the Contract/PR No. listed in Block E.

A. CONTRACT LINE ITEM NO.

B. EXHIBIT

A

C. CATEGORY

TDP

TM

OTHER

X

D. SYSTEM/ITEM

FT3 Production Follow-On

E. CONTRACT/PR NO.

FA8214-28-C-XXXX

F. CONTRACTOR

Boeing - Defense, Space & Security

1. DATA ITEM NO.

A002

2. TITLE OF THE DATA ITEM

Meeting Agenda

3. SUBTITLE

4. AUTHORITY

(Data Acquisition Document No.)

DI-ADMN-81249C

5. CONTRACT REFERENCE

PWS Para 2.1.5

6. REQUIRING OFFICE

AFNWC/NIMG

17. PRICE GROUP

18.

ESTIMATED TOTAL PRICE

7. DD 250 REQ

LT

8. APP CODE

N/A

9.

DIST STATEMENT REQUIRED

D

10. FREQUENCY

As Reqd

12.

DATE OF FIRST SUBMISSION

N/A

11. AS OF DATE

N/A

13.

DATE OF SUBSEQUENT SUBMISSION

N/A

14.

DISTRIBUTION

a. ADDRESSEE

b. COPIES

Draft

Final Reg Repro

LM

26-11

ORG 1 (LODO)

ORG 2 (LODO)

ORG 32 (LODO)

ORG 33 (LODO)

16. REMARKS: Changes to office symbols, when necessary, shall be made by the CO/ACO without revisions to the CDRL.

BLOCK 9:

Distribution Statement D: (see paras 5.3 & 5.4 of instructions for distribution statement, warning, and destruction notices, and CUI marking requirements).

BLOCKS 10, 11, 12 & 13:

Contractor shall submit Meeting Agenda, if applicable, NLT 5 business days prior to scheduled meetings or meetings deemed necessary by the Government.

Government will be allowed 2 business days, after receipt from contractor, to review for approval/disapproval/comments. Contractor shall submit revised Meeting Agenda incorporating Government comments, if applicable, NLT 2 business days after receipt from Government.

BLOCK 14:

For unclassified deliverables, contractor shall submit Meeting Agenda to TopVue https://icbm.topvue.com/topvue-icbm/ as per instructions (see paragraph 6.3.1).

For classified deliverables, contractor shall submit Meeting Agenda via instructions (see paragraph 6.3.2), and a letter of delivery to TopVue.

15. TOTAL

G. PREPARED BY

H. DATE

I. APPROVED BY

J. DATE

DD FORM 1423-1, FEB 2001

PREVIOUS EDITION MAY BE USED.

Page 1 of 1 Pages

Form Approved OMB No. 0704-0188

The public reporting burden for this collection of information is estimated to average 110 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to the Department of Defense, Executive Services and Communications Directorate (07040188). Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number.

Please do not return your form to the above organization. Send completed form to the Government Issuing Contracting Officer for the Contract/PR No. listed in Block E.

C. CATEGORY

TDP

TM

E. CONTRACT/PR NO.

FA8214-28-C-XXXX

F. CONTRACTOR

Boeing - Defense, Space & Security

1. DATA ITEM NO.

A003

2. TITLE OF THE DATA ITEM

Briefing Material

DI-MGMT-81605

5. CONTRACT REFERENCE

PWS Para 2.1.5

8. APP CODE

N/A

9.

DIST STATEMENT REQUIRED

D

10. FREQUENCY

As Reqd

12.

DATE OF FIRST SUBMISSION

SEE BLK 16

11. AS OF DATE

N/A

13.

DATE OF SUBSEQUENT SUBMISSION

N/A

Reg Repro

LM

16. REMARKS: Changes to office symbols, when necessary, shall be made by the CO/ACO without revisions to the CDRL.

Distribution Statement D: (see paras 5.3 & 5.4 of instructions for distribution statement, warning, and destruction notices, and CUI marking requirements).

BLOCKS 10, 11, 12 & 13:

Contractor shall submit Briefing Materials NLT 5 business days prior to each scheduled meeting and/or any other meeting deemed necessary by the Government and as requested by the Government. Government will be allowed 2 business days, after receipt from contractor, to review for comments.

Contractor shall present corrected Briefing Materials incorporating Government comments, if applicable, NLT 2 business days after receipt from Government.

BLOCK 14:

For unclassified deliverables, contractor shall submit Briefing Materials to TopVue https://icbm.topvue.com/topvue-icbm/ as per instructions (see paragraph 6.3.1).

For classified deliverables, contractor shall submit Briefing Materials via instructions (see paragraph 6.3.2), and a letter of delivery to TopVue.

15. TOTAL

Form Approved OMB No. 0704-0188

The public reporting burden for this collection of information is estimated to average 110 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to the Department of Defense, Executive Services and Communications Directorate (07040188). Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number.

Please do not return your form to the above organization. Send completed form to the Government Issuing Contracting Officer for the Contract/PR No. listed in Block E.

C. CATEGORY

TDP

TM

E. CONTRACT/PR NO.

FA8214-28-C-XXXX

F. CONTRACTOR

Boeing - Defense, Space & Security

1. DATA ITEM NO.

A004

2. TITLE OF THE DATA ITEM

Meeting Minutes

DI-ADMN-81250C

5. CONTRACT REFERENCE

PWS Para 2.1.5

8. APP CODE

N/A

9.

DIST STATEMENT REQUIRED

D

10. FREQUENCY

As Reqd

12.

DATE OF FIRST SUBMISSION

SEE BLK 16

11. AS OF DATE

N/A

13.

DATE OF SUBSEQUENT SUBMISSION

SEE BLK 16

Reg Repro

LM

16. REMARKS: Changes to office symbols, when necessary, shall be made by the CO/ACO without revisions to the CDRL.

Distribution Statement D: (see paras 5.3 & 5.4 of instructions for distribution statement, warning, and destruction notices, and CUI marking requirements).

BLOCKS 10, 11, 12 & 13:

Contractor shall submit Meeting Minutes NLT 15 business days after meeting or event has been held. Government will be allowed 5 business days, after receipt from contractor, to review for approval/disapproval/comments.

Contractor shall submit revised Meeting Minutes incorporating Government comments, if applicable, NLT 5 business days after receipt from Government.

BLOCK 14:

For unclassified deliverables, contractor shall submit Meeting Minutes to TopVue https://icbm.topvue.com/topvue-icbm/ as per instructions (see paragraph 6.3.1). For classified deliverables, contractor shall submit Meeting Minutes via instructions (see paragraph 6.3.2), and a letter of delivery to TopVue.

15. TOTAL

Form Approved OMB No. 0704-0188

The public reporting burden for this collection of information is estimated to average 110 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to the Department of Defense, Executive Services and Communications Directorate (07040188). Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number.

Please do not return your form to the above organization. Send completed form to the Government Issuing Contracting Officer for the Contract/PR No. listed in Block E.

C. CATEGORY

TDP

TM

E. CONTRACT/PR NO.

FA8214-28-C-XXXX

F. CONTRACTOR

Boeing - Defense, Space & Security

1. DATA ITEM NO.

A008.1

2. TITLE OF THE DATA ITEM

Work Management Plan

3. SUBTITLE

Subcontractor Management Plan

4. AUTHORITY

(Data Acquisition Document No.)

DI-MGMT-81911/T

5. CONTRACT REFERENCE

PWS Para 2.1.8.1.1

8. APP CODE

N/A

9.

DIST STATEMENT REQUIRED

D

10. FREQUENCY

As Reqd

12.

DATE OF FIRST SUBMISSION

SEE BLK 16

11. AS OF DATE

SEE BLK 16

13.

DATE OF SUBSEQUENT SUBMISSION

SEE BLK 16

Reg Repro

LM

ORG 34 (LODO)

16. REMARKS: Changes to office symbols, when necessary, shall be made by the CO/ACO without revisions to the CDRL.

Distribution Statement D: (see paras 5.3 & 5.4 of instructions for distribution statement, warning, and destruction notices, and CUI marking requirements).

BLOCKS 10, 11, 12 & 13:

Contractor shall submit Work Management Plan (Subcontractor Management Plan) NLT 30 business days after request from Government. Government will be allowed 20 business days, after receipt from contractor, to review for approval/disapproval/comments. Contractor shall submit revised Work Management Plan (Subcontractor Management Plan) incorporating Government comments, if applicable, NLT 20 business days after receipt from Government.

BLOCK 14:

For unclassified deliverables, contractor shall submit Work Management Plan (Subcontractor Management Plan) to TopVue https:

//icbm.topvue.com/topvue-icbm/ as per instructions (see paragraph 6.3.1).

For classified deliverables, contractor shall submit Work Management Plan (Subcontractor Management Plan) via instructions (see paragraph 6.3.2), and a letter of delivery to TopVue.

15. TOTAL

Form Approved OMB No. 0704-0188

The public reporting burden for this collection of information is estimated to average 110 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to the Department of Defense, Executive Services and Communications Directorate (07040188). Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number.

Please do not return your form to the above organization. Send completed form to the Government Issuing Contracting Officer for the Contract/PR No. listed in Block E.

C. CATEGORY

TDP

TM

E. CONTRACT/PR NO.

FA8214-28-C-XXXX

F. CONTRACTOR

Boeing - Defense, Space & Security

1. DATA ITEM NO.

A008.2

2. TITLE OF THE DATA ITEM

Work Management Plan

3. SUBTITLE

Small Business Subcontractor Report

4. AUTHORITY

(Data Acquisition Document No.)

DI-MGMT-81911/T

5. CONTRACT REFERENCE

PWS Para 2.1.8.1.2

8. APP CODE

N/A

9.

DIST STATEMENT REQUIRED

D

10. FREQUENCY

As Reqd

12.

DATE OF FIRST SUBMISSION

SEE BLK 16

11. AS OF DATE

SEE BLK 16

13.

DATE OF SUBSEQUENT SUBMISSION

SEE BLK 16

Reg Repro

LM

16. REMARKS: Changes to office symbols, when necessary, shall be made by the CO/ACO without revisions to the CDRL.

Distribution Statement D: (see paras 5.3 & 5.4 of instructions for distribution statement, warning, and destruction notices, and CUI marking requirements).

BLOCKS 10, 11, 12 & 13:

Contractor shall submit Work Management Plan (Small Business Subcontractor Report) NLT 30 business days after request from Government. Government will be allowed 20 business days, after receipt from contractor, to review for approval/disapproval/comments. Contractor shall submit revised Work Management Plan (Small Business Subcontractor Report) incorporating Government comments, if applicable, NLT 20 business days after receipt from Government.

BLOCK 14:

For unclassified deliverables, contractor shall submit Work Management Plan (Small Business Subcontractor Report) to TopVue https:

//icbm.topvue.com/topvue-icbm/ as per instructions (see paragraph 6.3.1). For classified deliverables, contractor shall submit Work Management Plan (Small Business Subcontractor Report) via instructions (see paragraph 6.3.2) , and a letter of delivery to TopVue.

15. TOTAL

Form Approved OMB No. 0704-0188

The public reporting burden for this collection of information is estimated to average 110 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to the Department of Defense, Executive Services and Communications Directorate (07040188). Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number.

Please do not return your form to the above organization. Send completed form to the Government Issuing Contracting Officer for the Contract/PR No. listed in Block E.

C. CATEGORY

TDP

TM

E. CONTRACT/PR NO.

FA8214-28-C-XXXX

F. CONTRACTOR

Boeing - Defense, Space & Security

1. DATA ITEM NO.

A008.3

2. TITLE OF THE DATA ITEM

Work Management Plan

3. SUBTITLE

Transportation Plan

4. AUTHORITY

(Data Acquisition Document No.)

DI-MGMT-81911/T

5. CONTRACT REFERENCE

PWS Para 2.1.7.3

8. APP CODE

N/A

9.

DIST STATEMENT REQUIRED

D

10. FREQUENCY

As Reqd

12.

DATE OF FIRST SUBMISSION

SEE BLK 16

11. AS OF DATE

SEE BLK 16

13.

DATE OF SUBSEQUENT SUBMISSION

SEE BLK 16

Reg Repro

LM

16. REMARKS: Changes to office symbols, when necessary, shall be made by the CO/ACO without revisions to the CDRL.

Distribution Statement D: (see paras 5.3 & 5.4 of instructions for distribution statement, warning, and destruction notices, and CUI marking requirements).

BLOCKS 10, 11, 12 & 13:

Contractor shall submit Work Management Plan (Transportation Plan) NLT 30 business days after request from Government. Government will be allowed 20 business days, after receipt from contractor, to review for approval/disapproval/comments. Contractor shall submit revised Work Management Plan (Transportation Plan) incorporating Government comments, if applicable, NLT 20 business days after receipt from Government.

BLOCK 14:

For unclassified deliverables, contractor shall submit Work Management Plan (Transportation Plan) to TopVue https://icbm.topvue.com/topvue-icbm/ as per instructions (see paragraph 6.3.1). For classified deliverables, contractor shall submit Work Management Plan (Transportation Plan) via instructions (see paragraph 6.3.2), and a letter of delivery to TopVue.

15. TOTAL

Form Approved OMB No. 0704-0188

The public reporting burden for this collection of information is estimated to average 110 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to the Department of Defense, Executive Services and Communications Directorate (07040188). Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number.

Please do not return your form to the above organization. Send completed form to the Government Issuing Contracting Officer for the Contract/PR No. listed in Block E.

C. CATEGORY

TDP

TM

E. CONTRACT/PR NO.

FA8214-28-C-XXXX

F. CONTRACTOR

Boeing - Defense, Space & Security

1. DATA ITEM NO.

A009

2. TITLE OF THE DATA ITEM

Manufacturing Plan

DI-MGMT-81889B

5. CONTRACT REFERENCE

PWS Para 2.1.6.1

8. APP CODE

N/A

9.

DIST STATEMENT REQUIRED

D

10. FREQUENCY

As Reqd

12.

DATE OF FIRST SUBMISSION

SEE BLK 16

11. AS OF DATE

SEE BLK 16

13.

DATE OF SUBSEQUENT SUBMISSION

SEE BLK 16

Reg Repro

LM

16. REMARKS: Changes to office symbols, when necessary, shall be made by the CO/ACO without revisions to the CDRL.

Distribution Statement D: (see paras 5.3 & 5.4 of instructions for distribution statement, warning, and destruction notices, and CUI marking requirements).

BLOCKS 10, 11, 12 & 13:

Contractor shall submit an updated Manufacturing Plan NLT 30 days upon request from the Government. Government will be allowed 15 business days, after receipt from contractor, to review for approval/disapproval/comments. Contractor shall submit updated Manufacturing Plan incorporating Government comments, if applicable, NLT 10 days after receipt from Government.

BLOCK 14:

For unclassified deliverables, contractor shall submit Manufacturing Plan to TopVue https://icbm.topvue.com/topvue-icbm/ as per instructions (see paragraph 6.3.1). For classified deliverables, contractor shall submit Manufacturing Plan via instructions (see paragraph 6.3.2), and a letter of delivery to TopVue.

15. TOTAL

Form Approved OMB No. 0704-0188

The public reporting burden for this collection of information is estimated to average 110 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to the Department of Defense, Executive Services and Communications Directorate (07040188). Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number.

Please do not return your form to the above organization. Send completed form to the Government Issuing Contracting Officer for the Contract/PR No. listed in Block E.

C. CATEGORY

TDP

TM

E. CONTRACT/PR NO.

FA8214-28-C-XXXX

F. CONTRACTOR

Boeing - Defense, Space & Security

1. DATA ITEM NO.

A010

2. TITLE OF THE DATA ITEM

Contractor's Risk Management Plan

DI-MGMT-81808

5. CONTRACT REFERENCE

PWS Para 2.1.8.2.1

8. APP CODE

N/A

9.

DIST STATEMENT REQUIRED

D

10. FREQUENCY

As Reqd

12.

DATE OF FIRST SUBMISSION

SEE BLK 16

11. AS OF DATE

N/A

13.

DATE OF SUBSEQUENT SUBMISSION

SEE BLK 16

Reg Repro

LM

16. REMARKS: Changes to office symbols, when necessary, shall be made by the CO/ACO without revisions to the CDRL.

Distribution Statement D: (see paras 5.3 & 5.4 of instructions for distribution statement, warning, and destruction notices, and CUI marking requirements).

BLOCKS 10, 11, 12 & 13:

Contractor shall submit an updated Contractor’s Risk Management Plan NLT 30 days upon requested from the Government. Government will be allowed 15 business days, after receipt from contractor, to review for comment. Contractor shall submit revised Risk Management Plan incorporating Government comments, if applicable, NLT 15 days after receipt from Government. Contractor shall submit subsequent submittals NLT 10 days after Government request.

BLOCK 14:

For unclassified deliverables, contractor shall submit Contractor’s Risk Management Plan to TopVue https://icbm.topvue.com/topvue-icbm/ as per instructions (see paragraph 6.3.1). For classified deliverables, contractor shall submit Contractor’s Risk Management Plan via instructions (see paragraph 6.3.2), and a letter of delivery to TopVue.

15. TOTAL

Form Approved OMB No. 0704-0188

The public reporting burden for this collection of information is estimated to average 110 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to the Department of Defense, Executive Services and Communications Directorate (07040188). Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number.

Please do not return your form to the above organization. Send completed form to the Government Issuing Contracting Officer for the Contract/PR No. listed in Block E.

C. CATEGORY

TDP

TM

E. CONTRACT/PR NO.

FA8214-28-C-XXXX

F. CONTRACTOR

Boeing - Defense, Space & Security

1. DATA ITEM NO.

A013

2. TITLE OF THE DATA ITEM

Corrosion Prevention and Control Plan (CPCP)

DI-MFFP-81403B

5. CONTRACT REFERENCE

PWS Para 2.1.6.3

AFNWC/NIMES

8. APP CODE

A

9.

DIST STATEMENT REQUIRED

D

10. FREQUENCY

As Reqd

12.

DATE OF FIRST SUBMISSION

SEE BLK 16

11. AS OF DATE

SEE BLK 16

13.

DATE OF SUBSEQUENT SUBMISSION

SEE BLK 16

Reg Repro

LM

ORG 12 (LODO)

16. REMARKS: Changes to office symbols, when necessary, shall be made by the CO/ACO without revisions to the CDRL.

Distribution Statement D: (see paras 5.3 & 5.4 of instructions for distribution statement, warning, and destruction notices, and CUI marking requirements).

BLOCKS 10, 11, 12 & 13:

Contractor shall submit an updated Corrosion Prevention & Control Plan (CPCP) NLT 30 calendar days upon request from the Government. Government will be allowed 15 business days, after receipt from contractor, to review for comment. Contractor shall submit revised CPCP incorporating Government comments, if applicable, NLT 10 days after receipt from Government.

Contractor shall submit a final Corrosion Prevention & Control Plan NLT 30 calendar days prior to PDR. Thereafter, contractor shall submit the Corrosion Prevention & Control Plan NLT 30 calendar days after a required change/modification to the plan is identified.

For each Corrosion Prevention & Control Plan submittal, Government will be allowed 30 calendar days, after receipt from contractor, to review for approval/disapproval/comments. If comments are returned, Contractor shall adjudicate comments with originator or delegate and submit revised Corrosion Prevention & Control Plan incorporating Government comments NLT 30 calendar days after receipt of final comments from Government.

BLOCK 14:

For unclassified deliverables, contractor shall submit Corrosion Prevention & Control Plan to TopVue https://icbm.topvue.com/topvue-icbm/ as per instructions (see paragraph 6.3.1). For classified deliverables, contractor shall submit Corrosion Prevention & Control Plan via instructions (see paragraph 6.3.2), and a letter of delivery to TopVue.

15. TOTAL

Form Approved OMB No. 0704-0188

The public reporting burden for this collection of information is estimated to average 110 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to the Department of Defense, Executive Services and Communications Directorate (07040188). Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number.

Please do not return your form to the above organization. Send completed form to the Government Issuing Contracting Officer for the Contract/PR No. listed in Block E.

C. CATEGORY

TDP

TM

E. CONTRACT/PR NO.

FA8214-28-C-XXXX

F. CONTRACTOR

Boeing - Defense, Space & Security

1. DATA ITEM NO.

A015

2. TITLE OF THE DATA ITEM

Quality Assurance Program Plan (QAPP)

DI-QCIC-81794B

5. CONTRACT REFERENCE

PWS Para 2.1.6.5

8. APP CODE

N/A

9.

DIST STATEMENT REQUIRED

D

10. FREQUENCY

As Reqd

12.

DATE OF FIRST SUBMISSION

SEE BLK 16

11. AS OF DATE

SEE BLK 16

13.

DATE OF SUBSEQUENT SUBMISSION

SEE BLK 16

Reg Repro

LM

16. REMARKS: Changes to office symbols, when necessary, shall be made by the CO/ACO without revisions to the CDRL.

Distribution Statement D: (see paras 5.3 & 5.4 of instructions for distribution statement, warning, and destruction notices, and CUI marking requirements).

BLOCKS 10, 11, 12 & 13:

Contractor shall submit an updated Quality Assurance Program Plan NLT 30 days upon request by the Government. Government will be allowed 15 business days, after receipt from contractor, to review for comment. Contractor shall submit revised QAPP incorporating Government comments, if applicable, NLT 10 days after receipt from Government.

BLOCK 14:

For unclassified deliverables, contractor shall submit Quality Assurance Program Plan to TopVue https://icbm.topvue.com/topvue-icbm/ as per instructions (see paragraph 6.3.1). For classified deliverables, contractor shall submit Quality Assurance Program Plan via instructions (see paragraph 6.3.2), and a letter of delivery to TopVue.

NOTE: Quality Assurance Program Plan shall be submitted IAW AS 9100.

15. TOTAL

Form Approved OMB No. 0704-0188

The public reporting burden for this collection of information is estimated to average 110 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to the Department of Defense, Executive Services and Communications Directorate (07040188). Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number.

Please do not return your form to the above organization. Send completed form to the Government Issuing Contracting Officer for the Contract/PR No. listed in Block E.

C. CATEGORY

TDP

TM

E. CONTRACT/PR NO.

FA8214-28-C-XXXX

F. CONTRACTOR

Boeing - Defense, Space & Security

1. DATA ITEM NO.

A059.1

2. TITLE OF THE DATA ITEM

Technical Report - Study/Services

3. SUBTITLE

Failure/Anomaly Resolution Report

4. AUTHORITY

(Data Acquisition Document No.)

DI-MISC-80508B/T

5. CONTRACT REFERENCE

PWS Paras 2.1.3.9, 2.1.3.10

AFNWC/NIMES/SIV

8. APP CODE

A

9.

DIST STATEMENT REQUIRED

D

10. FREQUENCY

As Reqd

12.

DATE OF FIRST SUBMISSION

SEE BLK 16

11. AS OF DATE

SEE BLK 16

13.

DATE OF SUBSEQUENT SUBMISSION

SEE BLK 16

Reg Repro

LM

16. REMARKS: Changes to office symbols, when necessary, shall be made by the CO/ACO without revisions to the CDRL.

BLOCK 4:

1. Paragraph 2., add the words “Contractor Format Acceptable” after Format.

2. Delete paragraphs 2. (a) & (b) in their entirety.

BLOCK 9:

Distribution Statement D: (see paras 5.3 & 5.4 of instructions for distribution statement, warning, and destruction notices, and CUI marking requirements).

BLOCKS 10, 11, 12 & 13:

Contractor shall submit Technical Report – Study/Services (Failure/Anomaly Resolution Report) NLT 30 days after completion of analysis. Government will be allowed 20 business days, after receipt from contractor, to review for approval/disapproval/comment. Contractor shall submit revised Technical Report – Study/Services (Failure/Anomaly Resolution Report) incorporating Government comments, if applicable, NLT 10 days after receipt from Government.

BLOCK 14:

For unclassified deliverables, contractor shall submit Technical Report – Study/Services (Failure/Anomaly Resolution Report) to TopVue https://icbm.topvue.com/topvue-icbm/ as per instructions (see paragraph 6.3.1).

For classified deliverables, contractor shall submit Technical Report – Study/Services (Failure/Anomaly Resolution Report) via instructions (see paragraph 6.3.2), and a letter of delivery to TopVue.

15. TOTAL

Form Approved OMB No. 0704-0188

The public reporting burden for this collection of information is estimated to average 110 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the…