26B9226034 Renovate Building 40 (Boiler) - Drawings.pdf

PDF 586 KB Posted Jul 6, 2026

Attached to: 511/26406. AGY; USPFO Warehouse - Renovate Building 40
Solicitation number: RFQ 171 260000000381 1
Issued by: Michigan

About this file

Written by GovTribe AI · Jul 7, 2026

Summary of Project Files

This is a construction drawing set for the Michigan Department of Military and Veterans Affairs (DMVA) renovation project of Building 40 at the USPFO facility located at 3405 N MLK Jr. Boulevard in Lansing, Michigan (Project No. 26B9226034). The project scope includes replacement of an existing condensing boiler (B-1) with a new AERCO Benchmark 2000 boiler rated at 2,000 input MBH and 1,920 output MBH, relocation and modification of associated hydronic piping and gas piping systems, installation of new boiler controls integrated with the existing Trane Tracer Summit building management system, installation of a new air/dirt separator, a carbon monoxide alarm, boiler neutralizing kits, and a new roof hydrant assembly above the janitor closet. The work also includes electrical modifications such as installation of a new 20-amp single-pole circuit breaker, removal of outdated boiler controls from the existing Boiler B-2, coordination of lead/lag boiler operation with outdoor temperature reset, and roof work requiring certification of the existing Firestone PVC roof warranty (RO029074/700181624). The contract is solicited on a lump sum basis with no bid alternates, and the contractor is required to maintain a building temperature minimum of 55 degrees Fahrenheit if the boiler is offline during replacement. Project management is handled by Ben Kopietz, Project Manager/Designer, and Randon Gould, Owner's Field Representative, with all work subject to DMVA approval and inspection.

The drawings indicate that existing boiler removal will result in a net electrical load reduction of 14.8 amperes at 208 volts, 3-phase, eliminating the need for main switchboard upgrades as the 1600-ampere main service has sufficient capacity. The contractor is responsible for field verification of all dimensions, site visits prior to bidding, documentation of existing conditions to prevent miscontrual of pre-existing damage, and coordination with the boiler manufacturer for startup, testing, and commissioning. All permits including building, mechanical, boiler, plumbing, electrical, and low-voltage electrical permits are required. The work must comply with applicable codes including the National Electrical Code and National Fuel Gas Code, with specifications requiring DDC (direct digital control) commissioning including 8 hours with in-house DDC and mechanical technicians, CSD-1 certification on the new boiler, and operator training. Site operations occur during posted hours of 7:45 AM to 4:30 PM, and the contractor must maintain a knowledgeable on-site representative at all times with copies of all contract specifications, drawings, and DMVA-approved shop drawings.

View the file

Other files

File	Type	Posted
USPFO WH ASBESTOS SURVEY PROJECT.pdf	PDF	Jul 6, 2026
SAM DAVIS BACON WAGE RATES INGHAM COUNTY BUILDING.pdf	PDF	Jul 6, 2026
Lansing USPFO Annex proj 11043 Pb,Cd,Cr in wipes.pdf	PDF	Jul 6, 2026
BABAA Compliance - Bldg 40 Boiler.pdf	PDF	Jul 6, 2026
Service Disabled Veteran Owned Business Info Sheet 2025.pdf	PDF	Jul 6, 2026
511_26406_AGY DTMB0415 Advertisement.pdf	PDF	Jul 6, 2026
26B9226034 Renovate Building 40 (Boiler) - Project Manual.pdf	PDF	Jul 6, 2026

On GovTribe

Work with this file

Download the original file
Contacts named in this file
Similar government files
Ask GovTribe AI about this file

Try for free Login

Text version

The file's text, extracted by GovTribe without its formatting.

SITE VICINITY MAP

SHIPPING AND

RECEIVING

OPEN OFFICE

DATA

STORAGE

119OFFICE

RECRUITING &

RETENTION COMMAND

MI COMP. VAULT

127B

MP COMMAND VAULT

127A

USMC VAULT

VAULT

STAGING

PASSAGE

OFFICE

MI COMPANY

SUPPLY AREA

USPFO VAULT

STAGING AREA

OFFICE

MP COMMAND

SUPPLY

OFFICE

USMC SUPPLY

LOCKERS

STORAGE & DISTRIBUTION

WAREHOUSE

MATERIALS MANAGEMENT

STORAGE & DISTRIBUTION

ELECTRICAL EQUIPMENT

OPEN OFFICE

C.I.F. RECEIVING

& DISTRIBUTION

C.I.F. WAREHOUSE

PASSAGE

JANITOR CLOSET

TELECOM

BREAK

MENS

WOMENS

VEST.

FILES

CONFERENCE

OPEN OFFICE

OFFICE

MECHANICAL

MENS

136B

WOMENS

136A

JANITOR

136C

STORAGE

136D

WOMENS

118A

MENS

118B

SOUTH GATE

MAIN

ENTRANCE

SITE LOCATION MAP

MIDDLE GATE

CLOSED

NORTH GATE

EXIT ONLY

1 O F

USPFO BUILDING 40

3405 N MLK JR BLVD, LANSING, MI

RENOVATE BUILDING 40 (BOILER)

MICHIGAN DEPARTMENT OF MILITARY AND VETERANS AFFAIRS

PROJECT NO. 26B9226034

AREA OF WORK

AREA OF WORK #1

(BOILER ROOM)

USPFO BUILDING 40 LAYOUT1

1 SCALE: N.T.S.

C O

R U

O N

R D

O R

O D

N O

D R

C H

E O

F M

O F

H N

G Y, M

B U

D G

O C

U R

D R

A D

N D

N A

N D

C O

R U

O N

, R A, D

O F

D V

G , M

U N

PROJECT MANAGER/DESIGNER:

BEN KOPIETZ

(517) 481-7552

KOPIETZB@MICHIGAN.GOV

OWNERS FIELD REPRESENTATIVE:

RANDON GOULD

(517) 481-7584

GOULDR2@MICHIGAN.GOV

1. BIDS FOR CONSTRUCTION OF ALL WORK SHOWN ON THE PLANS ARE SOLICITED ON A LUMP SUM BASIS. NO SEPARATE PAYMENT OR ADJUSTMENTS TO THE LUMP SUM BID WILL BE MADE UNLESS SPECIFICALLY INDICATED ON THE PLANS AND IN THE PROPOSAL OR WHEN ADDITIONAL WORK IS

AUTHORIZED IN WRITING BY THE ENGINEER.

2. CONTRACTOR TO FIELD VERIFY ALL DIMENSIONS AND SHALL IMMEDIATELY NOTIFY THE DMVA

ENGINEER AND INSPECTOR OF ANY DEVIATION FROM THESE DRAWINGS.

3. THE CONTRACTOR AND HIS SUBCONTRACTORS AND/OR SUPPLIERS ARE RESPONSIBLE FOR

VISITING THE SITE PRIOR TO BIDDING TO VERIFY ALL EXISTING CONDITIONS AND DIMENSIONS.

4. THE CONTRACTOR SHALL HAVE A KNOWLEDGEABLE REPRESENTATIVE ON SITE AT ALL TIMES

DURING WORK UNDER THIS CONTRACT. THIS REPRESENTATIVE SHALL HAVE ON SITE, HIS OWN

COPY OF THE CONTRACT SPECIFICATIONS, DRAWINGS AND DMVA APPROVED SHOP DRAWINGS.

5. PRIOR TO THE START OF CONSTRUCTION, CONTRACTOR TO VERIFY CONDITION OF EXISTING

CONSTRUCTION. DOCUMENT ANY EXISTING CONDITION THAT COULD BE MISCONTRUED AS

DAMAGED DURING NEW CONSTRUCTION. NOTIFY DMVA OF EXISTING CONDITIONS IN WRITING

PRIOR TO THE COMMENCEMENT OF WORK.

6. DRAWINGS ARE NOT TO BE SCALED FOR DIMENSIONS.

7. ALL WORK MUST COMPLY WITH THE DRAWINGS AND SPECIFICATIONS. ANY REVISIONS REQUIRED

DUE TO FIELD CONDITIONS MUST BE REVIEWED AND APPROVED BY DMVA PROJECT DESIGNER AND

DMVA INSPECTOR PRIOR TO CONSTRUCTION.

8. DISCREPANCIES FOUND BETWEEN THE SPECIFICATIONS AND THE DRAWINGS SHALL BE SUBMITTED

TO DMVA IN THE FORM OF AN RFI FOR CLARIFICATION PRIOR TO ANY WORK INVOLVING THIS

DISCREPANCY.

GENERAL NOTES

CONTACT INFORMATION

1. HOURS OF OPERATION - 7:45 AM TO 4:30 PM

2. IF BOILER IS IN OPERATION DURING BOILER REPLACEMENT, CONTRACTOR IS REQUIRED TO

MAINTAIN BUILDING TEMPERATURE OF 55 DEGREES MINIMUM WHILE BOILER IS OFFLINE.

SITE SPECIFIC NOTES

1. BUILDING PERMIT

2. MECHANICAL PERMIT

3. BOILER PERMIT

4. PLUMBING PERMIT

5. ELECTRICAL PERMIT

6. LOW VOLTAGE ELECTRICAL PERMIT

STATE OF MICHIGAN PERMITS REQUIRED

DRAWING INDEX

1 - TITLE SHEET

2 - DEMO PLAN & NEW PLAN

3 - SCHEDULES, DETAILS & NOTES

BID ALTERNATES

NONE

ROOF WARRANTY INFORMATION

ROOF MANUFACTURER - FIRESTONE

WARRANTY NUMBER - RO029074 / 700181624

ROOF TYPE - PVC

ELECTRICAL CLOSET

PANEL LP EM

AREA OF WORK #2

(JANITOR CLOSET / ROOF)

AutoCAD SHX Text I-496

AutoCAD SHX Text

US127

AutoCAD SHX Text

BUS.27

AutoCAD SHX Text

W STATE RD

AutoCAD SHX Text

E STATE RD

AutoCAD SHX Text I-69

AutoCAD SHX Text

CAPITAL REGIONAL INTERNATIONAL AIRPORT

AutoCAD SHX Text

W STOLL RD

AutoCAD SHX Text

AIRPORT RD

AutoCAD SHX Text

SPARROW HOSPITAL

AutoCAD SHX Text

WOOD ST

AutoCAD SHX Text

DEWITT RD

AutoCAD SHX Text

E CLARK RD

AutoCAD SHX Text

W CLARK RD

AutoCAD SHX Text

CLINTON CO.

AutoCAD SHX Text

INGHAM CO.

AutoCAD SHX Text

CLINTON CO.

AutoCAD SHX Text

EATON CO.

AutoCAD SHX Text

E MICHIGAN AVE

AutoCAD SHX Text

SAGINAW AVE

AutoCAD SHX Text

W WILLOW HWY

AutoCAD SHX Text

ELMWOOD RD

AutoCAD SHX Text

SNOW RD

AutoCAD SHX Text

S CREYS RD

AutoCAD SHX Text

PROJECT LOCATION

AutoCAD SHX Text

NORTH

AutoCAD SHX Text

SCALE: N.T.S.

AutoCAD SHX Text MLK Jr. BLVD.

AutoCAD SHX Text

OAKLAND AVE

AutoCAD SHX Text

W SAGINAW HWY

AutoCAD SHX Text I-69

AutoCAD SHX Text

DEWITT RD

AutoCAD SHX Text

US127

AutoCAD SHX Text

LAKE LANSING RD

AutoCAD SHX Text

W WILLOW HWY

AutoCAD SHX Text

BUS 96

AutoCAD SHX Text

GRAND RIVER AVE

AutoCAD SHX Text

N WAVERLY RD

AutoCAD SHX Text

S WAVERLY RD

AutoCAD SHX Text

W MICHIGAN AVE

AutoCAD SHX Text

SHERIDAN RD

AutoCAD SHX Text

RAILROAD

AutoCAD SHX Text S89°59'49"E

AutoCAD SHX Text X

AutoCAD SHX Text

SHERIDAN ROAD

AutoCAD SHX Text

COMBINED SUPPORT MAINTENANCE SHOP (CSMS)

AutoCAD SHX Text

USPFO WAREHOUSE

AutoCAD SHX Text

MARTIN LUTHER KING JR. BLVD

AutoCAD SHX Text

RFSC NORTH

AutoCAD SHX Text

RFSC SOUTH

AutoCAD SHX Text

JOINT FORCE HEADQUATERS

AutoCAD SHX Text

RESERVE FORCES SUPPORT CENTER (RFSC) WEST

AutoCAD SHX Text

NORTH

AutoCAD SHX Text

SCALE: N.T.S.

AutoCAD SHX Text

ONLY

AutoCAD SHX Text

ONLY

AutoCAD SHX Text

ONLY

AutoCAD SHX Text

ONLY

AutoCAD SHX Text

ONLY

AutoCAD SHX Text

STORAGE 31

AutoCAD SHX Text

GUARD SHACK ENTER SITE HERE

AutoCAD SHX Text

TUEBOR

AutoCAD SHX Text U

AutoCAD SHX Text S

AutoCAD SHX Text Q

AutoCAD SHX Text U

AutoCAD SHX Text E

AutoCAD SHX Text R

AutoCAD SHX Text C

AutoCAD SHX Text I

AutoCAD SHX Text U

AutoCAD SHX Text P

AutoCAD SHX Text I

AutoCAD SHX Text S

AutoCAD SHX Text R

AutoCAD SHX Text C

AutoCAD SHX Text S

AutoCAD SHX Text N

AutoCAD SHX Text I

AutoCAD SHX Text E

AutoCAD SHX Text N

AutoCAD SHX Text M

AutoCAD SHX Text I

AutoCAD SHX Text S

AutoCAD SHX Text

KAB

AutoCAD SHX Text E

AutoCAD SHX Text R

AutoCAD SHX Text U

AutoCAD SHX Text P

AutoCAD SHX Text L

AutoCAD SHX Text S

AutoCAD SHX Text B

AutoCAD SHX Text U

AutoCAD SHX Text I

AutoCAD SHX Text A

AutoCAD SHX Text N

AutoCAD SHX Text E

AutoCAD SHX Text O

AutoCAD SHX Text E

AutoCAD SHX Text I

AutoCAD SHX Text M

AutoCAD SHX Text L

AutoCAD SHX Text A

AutoCAD SHX Text P

AutoCAD SHX Text A

AutoCAD SHX Text M

AutoCAD SHX Text C

AutoCAD SHX Text M

AutoCAD SHX Text U

AutoCAD SHX Text N

EXST

B-2

EXST

B-1

EXST

DWH-1

EXST AIR

SEPARATOR

HWHS HWHS HWHS HWHS

HWHR HWHR HWHR HWHR HWHR HWHR HWHR HWHR

HWHS HWHS HWHS HWHS HWHS HWHS

HWHS HWHS HWHS HWHS HWHS HWHS HWHS HWHS HWHS

HWHS HWHS HWHS HWHS HWHS HWHS HWHS HWHS

GAS GAS GAS GAS GAS GAS GAS GAS GAS GAS GAS GAS GAS GAS

GAS GAS GAS

EXST

HWP-1

EXST

HWP-2

EXST VFD EXISTING FD

EXST

EF-02

EXST

RH-01

EXST

UH-01

GAS GAS GAS GAS GAS GAS GAS GAS GAS GAS GAS

GAS

EXST FIRE

SUPPRESSION

F.D.

EXST SHOT

FEEDER EXST

EXPANSION

TANK

TRANE

CONTROLS

AERCO

BOILER

CONTROLS

EXST

MIXING

VALVE

HWHS HWHS HWHS HWHS AS

1 B

1 EXST

B-2

EXST

DWH-1

HWHS HWHS HWHS HWHS

HWHS HWHS HWHS HWHS HWHS HWHS

HWHS HWHS HWHS HWHS HWHS HWHS HWHS HWHS HWHS

HWHS HWHS HWHS HWHS HWHS HWHS HWHS HWHS

GAS GAS GAS GAS GAS GAS GAS GAS GAS GAS GAS GAS GAS GAS

GAS GAS

EXST

HWP-1

EXST

HWP-2

EXST VFD EXISTING FD

EXST

EF-02

EXST

RH-01

EXST

UH-01

EXST

EXPANSION

TANK

HWHR

2'-4"

HWHR HWHR HWHR HWHR HWHR HWHR HWHR HWHR

GAS GAS GAS GAS GAS GAS GAS GAS GAS GAS GAS

GAS

F.D.

EXST FIRE

SUPPRESSION

EXST SHOT

FEEDER

TRANE

CONTROLS

AERCO

BOILER

CONTROLS

EXST

MIXING

VALVE

RHA

2 O F

C O

R U

O N

R D

O R

O D

N O

D R

C H

E O

F M

O F

H N

G Y, M

B U

D G

O C

U R

D R

A D

N D

N A

N D

C O

R U

O N

, R A, D

O F

D V

G , M

U N

MECHANICAL ROOM DEMO PLAN NOTES:

DISCONNECT AND REMOVE EXISTING CONDENSING BOILER B-1. DISCONNECT SUPPLY AND RETURN PIPING AND REMOVE AS REQUIRED TO CONNECT TO NEW BOILER. REFER TO NEW MECHANICAL ROOM

PLAN FOR PIPING CONNECTION LOCATIONS.

DISCONNECT EXISTING GAS TRAIN AND GAS PIPING TO EXISTING BOILER B-1. PREPARE FOR NEW GAS

PIPE TO NEW BOILER. REFER TO PIPING DETAIL FOR NEW GAS TRAIN LAYOUT.

DISCONNECT EXISTING BOILER B-1 INTAKE PIPING & VENT PIPING. PREPARE FOR NEW INTAKE AND

VENT PIPING TO NEW BOILER.

DISCONNECT ELECTRICAL CIRCUIT TO BOILER B-1. REMOVE 20A 3P BREAKER AND MOVE TO CIRCUITS PANEL LP EM 26, 28, & 30. LABEL BREAKER AS SPARE. REFER TO SHEET 1 FOR PANEL LP EM

LOCATION.

DISCONNECT, LABEL & CAP AT BOTH ENDS #10 GA RED AND BLUE ELECTRICAL FEEDERS.

COORDINATE WITH DDC CONTRACTOR & BOILER MANUFACTURER TO REMOVE ALL EXISTING BOILER

ROOM CONTROLS AS NEEDED TO INSTALL NEW BOILER CONTROLS. CONTRACTOR TO ENSURE

EXISTING BOILER B-2 WILL COMMUNICATE WITH NEW BOILER AND RUN IN A LEAD/LAG MANNER AND

TEMPERATURE WILL BE BASED ON OUTDOOR RESET.

REMOVE EXISTING BOILER CONTROLS ON BOILER B-2 AS REQUIRED TO INSTALL NEW CONTROLS TO

COMMUNICATE WITH NEW BOILER B-1.

REMOVE EXISTING AIR SEPARATOR IN THIS LOCATION. PREPARE FOR NEW AIR/ DIRT SEPARATOR

PIPING CONNECTIONS.

PROVIDE AND INSTALL NEW BOILER B-1 PER MANUFACTURER'S RECOMMENDATIONS AT NEW LOCATION, REFER TO SCHEDULE & BOILER PIPING DETAIL ON SHEET 3. MODIFY BOILER PIPING & GAS PIPING AS REQUIRED TO MOVE BOILER TO NEW LOCATION SHOWN ON PLANS. INSTALL NEW BOILER STAINLESS STEEL VENT, EXTEND & RECONNECT EXISTING INTAKE PIPE PER MANUFACTURER'S RECOMMENDATIONS.

INSTALL NEW FLASHING PER MANUFACTURER. INSTALL NEW BOILER OUTDOOR RESET SENSOR ON NORTH FACING EXTERIOR WALL, ROUTE WIRE IN 3/4" CONDUIT FROM SENSOR TO BOILER CONTROLLER.

RECONNECT EXISITNG & NEW BOILER TO EXISTING TRANE TRACER SUMMIT DDC SYSTEM AS REQUIRED.

REFER TO BOILER SEQUENCE ON SHEET 3. CONTRACTOR IS RESPONSIBLE TO COORDINATE BOILER STARTUP, TEST AND CHECK WITH BOILER MANUFACTURER AND DMVA ENGINEERING. TESTING TO INCLUDE MANUFACTURER'S COMBUSTION TESTING PROCEDURE. CONTRACTOR TO PERFORM A CSD-1 ON NEW BOILER AND PROVIDE ON-SITE BOILER OPERATION AND MAINTENANCE TRAINING FOR MAINTENANCE

STAFF.

FOR ALL NEW ROOF WORK, CONTRACTOR TO CERTIFY EXISTING ROOF WARRANTY, SEE ROOF WARRANTY

INFORMATION ON TITLE SHEET.

INSTALL NEW 4" MECHANICALLY CONTROLLED ISOLATION VALVES FOR BOTH BOILERS ON THE INLET SIDE

OF THE BOILER PER MANUFACTURER'S RECOMENDATIONS. CONNECT TO BOILER CONTROLS PER

MANUFACTURER'S RECOMMENDATIONS. CONTROL VALVE TO CLOSE WHILE CORRESPONDING BOILER IS IN

STANDBY.

UPDATE CONTROLS ON EXISTING BOILER B-2 TO ALLOW FOR PROPER COMMUNICATION WITH NEW BOILER

B-1 PER MANUFACTURER'S RECOMMENDATIONS. INSTALL NEW TOUCHSCREEN AND UPDATE TO TO

VERSION 3.0 OR HIGHER.

CONNECT NEW BOILER TO NEW BOILER ELECTRICAL CIRCUIT 20A SINGLE POLE BREAKER USING EXISTING #10 GA BLACK & WHITE FEEDERS. REUSE EXISTING BOILER 1 DISCONNECT. REMOVE UNUSED FUSES AND

TURN OVER TO DMVA MAINTENANCE STAFF. ENSURE NEW CIRCUIT IS CONNECTED TO EXISTING

EMERGENCY BOILER SHUTOFF SWITCH.

INSTALL NEW GAS PIPE FROM EXISTING GAS PIPE BRANCH TO NEW BOILER B-1 AS REQUIRED. INSTALL NEW GAS SHUTOFF VALVE, REGULATOR, UNION, AND DIRT LEG. PAINT ALL NEW & EXISTING GAS PIPING SAFETY YELLOW. INSTALL GAS PIPING PER NATIONAL FUEL GAS CODE. REFER TO GAS PIPING DETAIL ON

SHEET 3.

CONNECT NEW BOILER TO EXISTING TRANE TRACER SUMMIT BUILDING MANAGEMENT SYSTEM AS

REQUIRED TO ENABLE/DISABLE BOILERS. REFER TO BOILER SEQUENCE ON SHEET 3.

PROVIDE AND INSTALL NEW INSULATED AIR/DIRT SEPARATOR AS-1 PER MANUFACTURER'S

RECOMMENDATIONS, SEE SCHEDULE ON SHEET 3. MODIFY EXISTING HYDRONIC PIPING AS REQUIRED TO

INSTALL. INSTALL NEW ISOLATION VALVES ON BOTH SIDES OF NEW AIR/DIRT SEPARATOR.

INSTALL NEW CARBON MONOXIDE ALARM CO-1, REFER TO SCHEDULE ON SHEET 3. CONNECT TO EXISTING

MECHANICAL ROOM ELECTRICAL CIRCUIT IN THIS LOCATION.

INSTALL NEW BOILER NEUTRALIZING KIT ON BOTH BOILERS PER MANUFACTURER'S RECOMMENDATIONS, SEE BOILER SCHEDULE ON SHEET 3. INSTALL AND SECURE NEW 3/4" PVC TO FLOOR DRAIN. ENSURE

CONDENSATE DOES NOT RUN ON CONCRETE FLOOR.

EXTEND HOUSEKEEPING PAD AS REQUIRED FOR NEW BOILER LOCATION. DOWEL INTO ADJACENT

HOUSEKEEPING PAD. USE #4 STEEL DOWELS @ 16" O.C. 16" LONG W/ 6" EMBEDDED & CENTERED INTO ADJACENT PAD. MAINTAIN 2" FROM EDGE CLEARANCE. PAINT EXISTING / NEW HOUSEKEEPING PAD SIDES AND

TOP 4" PERIMETER EDGE SAFETY YELLOW.

MECHANICAL ROOM NEW PLAN NOTES:

USPFO BUILDING 40 - ELECTRICAL BUILDING LOAD REMOVAL & ADDITION SUMMARY

WATTS

SHEET 2 LOAD REMOVED - 7,205 W

SHEET 2 LOAD ADDED +2,400 W

NET LOAD ADDED -4,805 W

NET AMPS ADDED @ 208V, 3Ø, 90%PF -14.8 Amps

USPFO BUILDING 40 - BUILDING LOADS & ELECTRICAL SYSTEM SIZE

BUILDING MAIN SERVICE GEAR SIZE: 1600 AMPERE BUS 3Ø

REMOVING 14.8 AMPERES TO THE MAIN ELECTRICAL GEAR DOES NOT EXCEED

THE LOAD CAPACITY OF THE BUILDING'S ELECTRICAL SYSTEM. BASED ON THE

ABOVE CALCULATIONS, UPGRADING THE MAIN SWITCHBOARD SIZE IS NOT

REQUIRED.

20A

35A

BKR

USE AND/OR AREA SERVED

FEEDER SIZE:

TYPE:

LOCATION:

MOUNTING:

HW PUMP #1 3P

USE AND/OR AREA SERVED

LOAD - vA

CCT vA vA CCT

120/208V, 3Ø, 4WVOLTAGE:

CONDUIT SIZE:

MIN. AIC:

BKR

10,000 A

200A M.C.B.MAINS:

USPFO PANELBOARD LP EM SCHEDULE

SURFACE

SQUARE D NQ ENCLOSURE

USPFO BUILDING 40

UH-1-2 / UH-1-7

UH-1-5

SPARE

UH-3-8

UH-3-1 / UH-3-3

UH-3-5 / UH-3-6

SPARE

20A 1P

ENLARGED USPFO MECHANICAL ROOM DEMO PLAN1

2.0 SCALE: 3/8" = 1'-0"

ENLARGED USPFO MECHANICAL ROOM PLAN2

2.0 SCALE: 3/8" = 1'-0"

5 6

3 3

1 2 3

4 5

35A 3P

20A 3P

HW PUMP #2

BOILER #2

UH-2-7 / UH-2-8

20A 1P

UH-2-4 / UH-2-1

20A 1P

LIFT PUMP

35A 2P

CONTROL CKT LIFT PUMP

20A 1P

20A 3P

SPARE

40A 2P

20A 1P

SPARE

20A 1P

-EMPTY

20A 1P

NEW BOILER B-1

ENLARGED USPFO JANITOR CLOSET / ROOF PLAN3

2.0 SCALE: 1/2" = 1'-0"

ENLARGED USPFO JANITOR CLOSET / ROOF PLAN NOTES:

INSTALL NEW ROOF HYDRANT ASSEMBLY RHA-1 ABOVE JANITOR CLOSET IN THIS LOCATION PER MANUFACTURER'S RECOMMENDATIONS, SEE SCHEDULE ON SHEET 3. CONNECT TO EXISTING COLD

WATER PIPING AS REQUIRED, REFER TO DETAIL ON SHEET 3.

FOR ALL NEW ROOF WORK, CONTRACTOR TO CERTIFY EXISTING ROOF WARRANTY, SEE ROOF

WARRANTY INFORMATION ON SHEET 1.

1 2

AutoCAD SHX Text M

AutoCAD SHX Text

TUEBOR

AutoCAD SHX Text U

AutoCAD SHX Text S

AutoCAD SHX Text Q

AutoCAD SHX Text U

AutoCAD SHX Text E

AutoCAD SHX Text R

AutoCAD SHX Text C

AutoCAD SHX Text I

AutoCAD SHX Text U

AutoCAD SHX Text P

AutoCAD SHX Text I

AutoCAD SHX Text S

AutoCAD SHX Text R

AutoCAD SHX Text C

AutoCAD SHX Text S

AutoCAD SHX Text N

AutoCAD SHX Text I

AutoCAD SHX Text E

AutoCAD SHX Text N

AutoCAD SHX Text M

AutoCAD SHX Text I

AutoCAD SHX Text S

AutoCAD SHX Text

KAB

AutoCAD SHX Text E

AutoCAD SHX Text R

AutoCAD SHX Text U

AutoCAD SHX Text P

AutoCAD SHX Text L

AutoCAD SHX Text S

AutoCAD SHX Text B

AutoCAD SHX Text U

AutoCAD SHX Text I

AutoCAD SHX Text A

AutoCAD SHX Text N

AutoCAD SHX Text E

AutoCAD SHX Text O

AutoCAD SHX Text E

AutoCAD SHX Text I

AutoCAD SHX Text M

AutoCAD SHX Text L

AutoCAD SHX Text A

AutoCAD SHX Text P

AutoCAD SHX Text A

AutoCAD SHX Text M

AutoCAD SHX Text C

AutoCAD SHX Text M

AutoCAD SHX Text U

NEUTRALIZING KIT

SHUTOFF VALVE

UNION

REDUCER AS REQUIRED

PUMP

PRESSURE GAUGE

PRESSURE RELIEF/SAFETY VALVE

MANUAL AIR VENT @ HIGH POINT

TEMPERATURE GAUGE

TEMP SENSOR BY DDC CONTRACTOR

GAS PRESSURE REGULATOR

CALIBRATED BALANCING VALVE

GAS SHUTOFF VALVE

END CAP

2-WAY CONTROL VALVE

3-WAY CONTROL VALVE

ACTUATOR BY DDC CONTRACTOR

DRAIN VALVE W/ CAP

CHECK VALVE

STRAINER w/ BLOW OFF VALVE

POINT OF NEW CONNECTION

EXISTING EQPM & PIPING

NEW PIPING

NEW EQUIPMENT

BOILER

6" MIN

DIRT LEG PVC TO DRAIN

SUPPLY

RETURN

GAS

PIPE

S, D

3 O F

C O

R U

O N

R D

O R

O D

N O

D R

C H

E O

F M

O F

H N

G Y, M

B U

D G

O C

U R

D R

A D

N D

N A

N D

C O

R U

O N

, R A, D

O F

D V

G , M

U N

GENERAL ENERGY MANAGEMENT NOTES:

1. PRIOR TO ANY INSTALLATION OF DDC EQUIPMENT OR DDC WIRING, CONTRACTOR

SHALL REQUEST A DDC PRECONSTRUCTION MEETING WITH DMVA ENGINEERING

TO DISCUSS CONSTRUCTION SCHEDULING, PRECISE DDC EQUIPMENT LOCATIONS,

STARTUPS, LABELING PROCEDURES, AND COMMISSIONING.

2. ALL DDC PROGRAMMING / SOURCE CODE INCLUDING ANY CUSTOM USER DEFINED

DEVICES OR UDD ALONG WITH ANY SOFTWARE NECESSARY TO RUN THE SYSTEM

TO BE TURNED OVER TO DMVA DDC TECHNICIAN UPON PROJECT COMPLETION.

3. DDC CONTRACTOR TO INCLUDE 8 HOURS OF DDC COMMISSIONING WITH IN-HOUSE

DDC / MECHANICAL TECHNICIAN.

4. ROUTE ALL DDC CONTROL WIRES PER SCHEDULE AND SPECIFICATIONS.

5. REFER TO DDC SCHEMATIC THIS SHEET FOR ADDITIONAL END DEVICES NOT

SHOWN ON PLANS.

6. CONTRACTOR TO INSTALL A MINIMUM 3/4" RIGID METAL CONDUIT FOR ALL DDC

WIRING. INSTALL MINIMUM 1/2" FLEXIBLE METAL CONDUIT TO ALL VIBRATING

EQUIPMENT, 5' MAX LENGTH. CONTRACTOR IS ALLOWED TO INSTALL J-HOOKS 4'

O.C. FOR DDC CONTROL WIRING ONLY IN AREAS ABOVE A SUSPENDED CEILING.

ALL CONDUIT IN WALLS TO BE STUBBED INTO CEILING SPACE.

7. CONTRACTOR SHALL PULL ALL DDC WIRING AS SHOWN ON DDC FLOOR PLAN AND

DDC EQUIPMENT SCHEDULE. ALL WIRES SHALL BE LABELED WITH A LABEL MAKER

APPROVED BY DMVA ENGINEERING. NO HAND WRITTEN LABELS WILL BE

ALLOWED. ALL LABELS LOCATED IN ENCLOSURE ENC-1 & 2 MUST BE PLACED 6"

DOWN ON WIRE ONCE INSIDE THE ENCLOSURE, DO NOT LOCATE LABEL AT THE

END OF WIRE.

8. ALL INPUT/OUTPUT CONTROL WIRES TO BE LON RATED, SEE SPECIFICATIONS.

9. DDC SEQUENCE AND PROGRAMMING WILL BE COMPLETED BY A DMVA APPROVED

SUBCONTRACTOR, SEE SPECIFICATIONS.

10. INSTALL TEMPERATURE SENSORS, TEMP-1, 60" AFF.

11. INSTALL OCCUPANCY SENSORS, OCC-1, 6" FROM CEILING.

12. INSTALL ALL OAT-1 ON NORTH FACING EXTERIOR WALL, MAKE WEATHERTIGHT

13. LABEL ALL DDC EQUIPMENT TO CORRESPOND TO DDC SCHEMATIC / DDC

SCHEDULE.

14. PROVIDE AND INSTALL ALL END DEVICES SHOWN ON PLANS.

15. COORDINATE WITH ELECTRICAL TO INSTALL NEW RELAYS. ELECTRICAL

CONTRACTOR WILL INSTALL J-BOX FOR NEW RELAYS TO MOUNT ON.

16. RELAYS FOR EXHAUST FANS TO BE LOCATED IN ELECTRICAL CLOSET.

COORDINATE WITH ELECTRICAL.

GENERAL ELECTRICAL NOTES:

1. SEAL ALL FIRE RATED WALL & CEILING PENETRATIONS.

2. COORDINATE LOCATIONS OF LIGHT FIXTURES WITH ALL PIPING, DUCTWORK, AND

EQUIPMENT. MOUNT LIGHT FIXTURES TO ALLOW THE GREATEST POSSIBLE

HEADROOM.

3. UNLESS OTHERWISE NOTED OR DETAILED, INSTALL ALL CONDUCTORS IN

CONDUIT.

4. ALL WORK SHALL BE INSTALLED IN ACCORDANCE WITH THE LATEST ACCEPTED

EDITION OF THE NATIONAL ELECTRICAL CODE AND ALL STATE AND LOCAL CODES.

5. PROVIDE EQUIPMENT GROUNDING CONDUCTORS IN EVERY POWER AND LIGHTING

CONDUIT, ONE GROUNDING CONDUCTOR FOR EACH CIRCUIT.

6. ALL LIGHTING AND POWER CONDUCTORS SHALL BE 12 AWG MINIMUM.

7. MINIMUM CONDUIT SIZE SHALL BE 3/4" INTERNAL DIAMETER.

8. MC (METAL CLAD) CABLE SHALL NOT BE USED ON THIS PROJECT.

9. CONTRACTOR SHALL TRANSITION FROM PVC CONDUIT TO GALVANIZED RIGID

METALLIC CONDUIT WHEN TURNING UP FROM BELOW A CONCRETE SLAB OR FROM

BELOW GRADE TO ABOVE GRADE, WHETHER INDOORS OR OUTDOORS, BY

INSTALLING A GALVANIZED METALLIC NINETY DEGREE ELBOW AND THEN

CONTINUING ABOVE SLAB OR GRADE UTILIZING GALVANIZED RIGID METAL

CONDUIT. THIS APPLIES TO ALL RACEWAYS FOR ALL SYSTEMS INCLUDING

VOICE/DATA, UTILITY POWER AND/OR EMERGENCY POWER, LIGHTING, &

COMMUNICATIONS SYSTEMS.

10. ELECTRICAL CONTRACTOR SHALL VERIFY AND UPDATE ALL PANELBOARD

SCHEDULE CIRCUIT CARDS. ANY UNUSED BREAKERS SHALL BE TURNED OFF AND

MARKED AS SPARES. LABELING OF EXISTING BREAKER SHOULD INDICATE WHAT IS

CONNECTED NOT AS NOTED IN SCHEDULES PROVIDED.

GENERAL DEMO NOTES:

1. CONTRACTOR TO PROVIDE PROPER DUST CONTROL MEASURES PER

SPECIFICATIONS.

2. CONTRACTOR TO MAINTAIN A CLEAN WORKSPACE AT THE END OF EACH DAY

PER SPECIFICATIONS.

3. DURING DEMOLITION, KEEP ALL ROOF AND EXTERIOR WALL PENETRATIONS

SEALED OFF FROM EXTERIOR.

GENERAL MECHANICAL NOTES:

1. FIRE CAULK ALL PENETRATIONS THRU MECHANICAL ROOM AND CORRIDOR WALLS.

2. PERFORM TEST AND BALANCE PER SPECIFICATIONS.

3. CONTRACTOR TO COORDINATE ALL NEW EQUIPMENT STARTUP AND TESTING.

4. PROVIDE ALL TRAINING PER SPECIFICATIONS.

5. ALL SUPPLY & RETURN PIPING TO BE INSULATED, SEE SPECIFICATIONS.

6. PROVIDE ACCESS TO ALL REQUIRED PIPING EQUIPMENT. INSTALL ACCESS

PANELS AS REQUIRED.

7. THESE DRAWINGS ARE DIAGRAMMATIC, AND REPRESENT THE GENERAL INTENT

AND ARRANGEMENT OF SYSTEMS. THEY ARE NOT TO BE CONSIDERED

FABRICATION/COORDINATION/SHOP DRAWINGS. COORDINATION WITH OTHER

TRADES IS REQUIRED. PROVIDE THE ADDITIONAL FITTINGS AND OFFSETS THAT

WILL BE REQUIRED TO COMPLETE EACH SYSTEM AND TO AVOID INTERFERENCES

WITH ALL OTHER SYSTEMS INCLUDING THE STRUCTURE, SHEET METAL, OTHER

PIPING SYSTEMS, ELECTRICAL CONDUITS, BUS DUCTS, CABLE TRAY, LIGHT

FIXTURES, ETC. AND/OR OTHER SPACE CONSTRAINTS.

8. ALL PUMPS LOCATED IN THE BOILER/MECHANICAL ROOM MUST BE ACCESSIBLE

FROM THE GROUND WITHOUT THE USE OF A LADDER.

1. CONTRACTOR TO FIELD VERIFY ALL DIMENSIONS. ANY DISCREPANCIES MUST BE

BROUGHT TO THE OWNER'S ATTENTION.

2. PRIOR TO THE START OF CONSTRUCTION, CONTRACTOR TO VERIFY CONDITION OF

EXISTING CONSTRUCTION. DOCUMENT ANY EXISTING CONDITION THAT COULD BE

MISCONSTRUED AS DAMAGED DURING NEW CONSTRUCTION. NOTIFY THE

GOVERNMENT OF EXISTING CONDITIONS IN WRITING PRIOR TO THE COMMENCEMENT

OF WORK.

3. WHERE NEW CONSTRUCTION ABUTS EXISTING CONSTRUCTION AND APPEARS TO

ALIGN FLUSH WITH EXISTING CONSTRUCTION, THE NEW CONSTRUCTION SHALL ALIGN

AND BE FLUSH WITH NO VISIBLE JOINT, UNLESS THE MATERIALS OR SUBSTRATES

DIFFER; THEN, AN EXPANSION JOINT SHALL BE INSTALLED.

4. DRAWINGS ARE NOT TO BE SCALED FOR ANY DIMENSIONS.

5. ALL WORK MUST COMPLY WITH THE DRAWINGS AND SPECIFICATIONS, ANY REVISIONS

REQUIRED DUE TO FIELD CONDITIONS MUST BE REVIEWED AND APPROVED BY THE

PROJECT MANAGER PRIOR TO CONSTRUCTION.

6. COORDINATE NEW AND RELOCATE ANY EXISTING CONDUITS, ETC. TO ACCOMMODATE

LIGHT FIXTURES, HVAC ACCESSORIES AND VARIOUS DEVICES.

7. PROVIDE ADDITIONAL WIRING, CONDUIT AND ACCESSORIES FOR DEVICES TO BE

RELOCATED. AT NO ADDITIONAL COST.

8. ALL WALL MOUNTED DEVICES SHALL BE FULLY CONCEALED UNLESS NOTED

OTHERWISE.

9. BIDS FOR CONSTRUCTION OF ALL WORK SHOWN ON THE PLANS ARE SOLICITED ON A

LUMP SUM BASIS. NO SEPARATE PAYMENT OR ADJUSTMENTS TO THE LUMP SUM BID

WILL BE MADE UNLESS SPECIFICALLY INDICATED ON THE PLANS AND IN THE

PROPOSAL OR WHEN ADDITIONAL WORK IS AUTHORIZED IN WRITING BY THE PROJECT

MANAGER.

10. THE CONTRACTOR SHALL HAVE A KNOWLEDGEABLE REPRESENTATIVE ON SITE AT ALL

TIMES DURING WORK UNDER THIS CONTRACT. THIS REPRESENTATIVE SHALL HAVE

ON SITE, HIS OWN COPY OF THE CONTRACT SPECIFICATIONS, DRAWINGS AND DMVA

APPROVED SHOP DRAWINGS.

11. CONTRACTOR TO SCHEDULE AND COORDINATE ALL SHUT-DOWNS WITH THE PROJECT

MANAGER, OWNER FIELD REPRESENTATIVE AND ALL DMVA SITE PERSONNEL.

12. CONTRACTOR TO FOLLOW SPECIFICATION FOR RECYCLING PROCEDURES. PROVIDE

WEIGHT SLIPS WHEN AVAILABLE.

GENERAL NOTES:

LEGEND HYDRONIC PIPING GENERAL NOTES:

1. SIZE GAS PIPING PER MANUFACTURER'S NATURAL GAS PIPE SIZE CHART.

2. DELETE REDUCERS AT UNIT IF UNIT CONNECTION IS SAME AS PIPE SIZE.

3. INSTALL MINIMUM 6" DIRT LEG PIPED PER DETAIL.

4. PAINT ALL NEW GAS PIPE SAFETY YELLOW.

5. MODIFY SUPPLY & RETURN PIPING AS REQUIRED TO CONNECT TO NEW BOILER.

6. INSTALL NEW BOILER CONDNESATE NEUTRALIZER. ROUTE 3/4" PVC TO NEAREST

DRAIN.

7. NEW PUMPS TO BE LOCATED AT A HEIGHT ONLY ACCESSIBLE FROM THE FLOOR

WITHOUT UTILIZING A LADDER OR OTHER HEIGHT EXTENDING TOOL.

8. INSTALL NEW HANGERS AND SUPPORTS AS REQUIRED.

9. INSULATE PIPING PER SPECIFICATIONS.

BOILER PIPING DETAIL NOTES:

BOILER PIPING DETAIL1

3 SCALE: NO SCALE

AIR / DIRT SEPARATOR SCHEDULE

AS-1 HEATING WATER CALEFFI NA546080AM 3" 117

MARK SERVING MFR

CONNECTION

SIZE (IN)

FLOW

(GPM) NOTES

MAGNETIC, INSULATED, FLANGED

GAS MONITORING EQUIPMENT SCHEDULE

BASIS OF DESIGN

MOUNTING

LOCATION NOTESDESCRIPTIONMARK

CO-1 CARBON MONOXIDE ALARM 48" AFF WALL MOUNTKIDDIE - KN-COB-IC

VOLTAGE

120 VAC

BOILER SCHEDULE

WATER

CONNECTION

IN.MARK BASIS OF DESIGN

INPUT

MBH

OUTPUT

MBH

GAS PRESSURE

MIN/MAX

IN W.C.

VENT

SIZE

IN.

WATER

PRESSURE

DROP FT.

GPM

MAX

EWT

°F

LWT

°F

ELECTRICAL

NOTES

FLA VOLTS PH HZ

B-1 AERCO BENCHMARK 2000 2,000 1,920 4/14 8" 4" FLANGED 120°F 140°F 16 120 1 603506.9 (2) AERCO NEUTRALIZING KIT 89025-2 INSTALLED IN SERIES

INTAKE

SIZE

IN.

MCA

TURNDOWN

RATIO

20:1

MODEL

1. INSTALL ALL EQUIPMENT PER MANUFACTURER'S

RECOMMENDATIONS.

2. INSTALL THREADED ROD, HANGERS AND SUPPORTS AS

REQUIRED.

3. NEW PUMPS TO BE LOCATED AT A HEIGHT ONLY ACCESSIBLE

FROM THE FLOOR WITHOUT UTILIZING A LADDER OR OTHER

HEIGHT EXTENDING TOOL.

4. INSTALL ALL TEMPERATURE GAUGES AS SHOWN. GAUGES TO BE

VISIBLE FROM A NORMAL INSPECTION LOCATION.

5. PIPE CONTROL VALVE TO NORMALLY OPEN THRU HEATING COIL IN

CASE OF FAILURE.

6. INSTALL REDUCERS AT CONTROL VALVES AS REQUIRED.

7. DELETE REDUCERS AT COILS IF COIL CONNECTION IS SAME AS

PIPE SIZE.

8. INSTALL UNIONS AT ALL PUMPS UNLESS PUMP IS FLANGED.

9. INSTALL MANUAL AIR VENT AT HIGH POINT AS SHOWN.

10. LABEL ALL EQUIPMENT AND HVAC/DOMESTIC PIPING. SIZE PER

SPECIFICATION.

11. INSTALL INSULATION ON ALL HYDRONIC & DOMESTIC HOT WATER

PIPING. SEE SPECIFICATIONS FOR THICKNESS.

HEATING HOT WATER BOILER SEQUENCE

THE BOILERS, AND ZONE PUMPS WILL BE ENABLED TO RUN WHEN THE OUTDOOR AIR TEMPERATURE FALLS BELOW THE PROGRAMMABLE BOILER ENABLE SET POINT, (60.0 DEGREES, ADJUSTABLE). A TWO DEGREE THROTTLING

RANGE WILL PREVENT SHORT CYCLING OF THE BOILER.

UPON A CALL FOR HEATING, THE LEAD HOT WATER CIRCULATING PUMP WILL BE ENERGIZED. ONCE WATER FLOW HAS BEEN CONFIRMED, THRU THE PUMPS ASSOCIATED CURRENT SENSOR, THE BOILERS WILL BE ENABLED.

THE BOILERS WILL BE STAGED TO MAINTAIN SET POINT BASED UPON THEIR INTERNAL OPERATING CONTROLS.

NOTES: INCLUDE 4" MOTORIZED ISOLATION VALVE

ROOF HYDRANT DETAIL2

3 SCALE: N.T.S.

ROOF HYDRANT ASSEMBLY SCHEDULE

MARK BASIS OF DESIGN TYPE NOTESDESCRIPTION

RHA-1 ROOF HYDRANT WOODFORD - RHY2-1-MS FREEZE PROOF DUAL CHECK BACKFLOW PREVENTER, SEE DETAIL THIS SHEET1" COLD WATER

CONNECTION SIZE

AutoCAD SHX Text

TUEBOR

AutoCAD SHX Text U

AutoCAD SHX Text S

AutoCAD SHX Text Q

AutoCAD SHX Text U

AutoCAD SHX Text E

AutoCAD SHX Text R

AutoCAD SHX Text C

AutoCAD SHX Text I

AutoCAD SHX Text U

AutoCAD SHX Text P

AutoCAD SHX Text I

AutoCAD SHX Text S

AutoCAD SHX Text R

AutoCAD SHX Text C

AutoCAD SHX Text S

AutoCAD SHX Text N

AutoCAD SHX Text I

AutoCAD SHX Text E

AutoCAD SHX Text N

AutoCAD SHX Text M

AutoCAD SHX Text I

AutoCAD SHX Text S

AutoCAD SHX Text

KAB

AutoCAD SHX Text E

AutoCAD SHX Text R

AutoCAD SHX Text U

AutoCAD SHX Text P

AutoCAD SHX Text L

AutoCAD SHX Text S

AutoCAD SHX Text B

AutoCAD SHX Text U

AutoCAD SHX Text I

AutoCAD SHX Text A

AutoCAD SHX Text N

AutoCAD SHX Text E

AutoCAD SHX Text O

AutoCAD SHX Text E

AutoCAD SHX Text I

AutoCAD SHX Text M

AutoCAD SHX Text L

AutoCAD SHX Text A

AutoCAD SHX Text P

AutoCAD SHX Text A

AutoCAD SHX Text M

AutoCAD SHX Text C

AutoCAD SHX Text M

AutoCAD SHX Text U

AutoCAD SHX Text N

AutoCAD SHX Text

HYDRANT SUPPORT ASSEMBLY

AutoCAD SHX Text

ROOF MEMBRANE FLASHING INTO BOOT COVER

AutoCAD SHX Text

ROOF INSULATION

AutoCAD SHX Text

ROOF DECKING

AutoCAD SHX Text

MOUNTING BOLTS (4)

AutoCAD SHX Text

UNDER DECK FLANGE

AutoCAD SHX Text

CLAMP SCREWS (3)

AutoCAD SHX Text

1/8 NPT DRAIN HOLE, CONNECT TO 1/2" PVC AND ROUTE TO MOP SINK

AutoCAD SHX Text

1" NPT INLET, CONNECT TO DOMESTIC COLD WATER SUPPLY PIPE

AutoCAD SHX Text

ROOF HYDRANT ASSEMBLY WOODFORD MODEL RHY2-1-MS

BOOT COVER

1 TITLE SHEET

Sheets and Views

1 TITLE SHEET

2 DEMO & NEW PLAN

Sheets and Views

2 DEMO & NEW PLAN

3 SCHEDULES DETAILS & NOTES

Sheets and Views

3 SCHEDULES DETAILS & NOTES

File details come from the government source that posted it. Updated Jul 7, 2026.