25-0002RR Exhibit A Specs Mobile Column Rotary Lifts.pdf

EXHIBIT A

ILLINOIS TOLLWAY’S SPECIFICATIONS

MOBILE COLUMN ROTARY LIFTS

The Vendor is required to complete and return with their bid the attached specification questionnaire and note any deviations from specifications for the unit(s) being provided. Units shall be the most current model design as offered by the factory and published in factory literature. Units shall meet all applicable State and Federal regulations. Detailed literature shall be provided for the mobile column lifts and any accessories and options at time of bid submission.

The specifications outlined in this document are intended to ensure the Tollway receives mobile column lifts that are suited for the tasks for which they are being procured. In many cases vehicle and equipment specifications and capabilities vary between manufacturers. Developing a single specification that provides adequate assurance to the Tollway of unit capability, reliability and cost effectiveness may not recognize subtle differences that exist between manufacturers. The Tollway reserves the right to review each bid to determine if any specification differences have a significant impact on the unit(s), capability, reliability or cost effectiveness at time of purchase or for the life of the unit(s). The Tollway’s determination of contract specification compliance and acceptable specification deviations shall be final.

The units to be supplied shall be Rotary Model MCHM19 or Tollway approved equal. The lifts shall be fully assembled and ready to operate when delivered.

Lifts must include the following:

1. Lifting capacity of 18,800 lbs minimum per individual column.

2. Hydraulic lifting system with microprocessor-controlled synchronization.

3. Automotive lift institute certified.

4. Automatic Overload protection system.

5. Dead Man switches on each column.

6. Manual lowering in case of power outage.

7. Adjustable pick-up forks up to 9 inches – 24 inches minimum.

8. Adjustable lowering speed.

9. 24 volt power supply, recharged by means of a 110 volt outlet.

10. 70 inch lifting height minimum.

11. Retractable wheels that raise to allow lift to rest on lift points and not the wheels.

12. 78 seconds maximum to lift from full down position to maximum lifting height.

13. Independent mechanical locking system.

14. Locking profile with multiple locking increments.

15. Waterproof electrical system.

16. Wireless control system must include.

a. User access control system to stop unauthorized use.

b. High resolution visual display with touch screen.

c. Controllers to have built in Help and instruction manual.

d. Safety system to ensure only the column lifts in a chosen group of column lifts are operated.

e. Battery charge indicator.

f. Lifting height is displayed on controllers.

17. One vehicle support stand per column (total of 8 stands). The stand shall have the minimum weight capacity of a column lift and shall have a minimum starting height of 50 to 54 inches and a maximum working height of 70 to 74 inches. The stand pin shall have an adjustment. The stand shall have a minimum of 2-3 inches of fine adjustment. The stand shall have transport wheels that are mounted in a manner that they are not in contact with the ground when stand is in the upright position.

18. A minimum of a one (1) year manufacturer warranty on the entire units (all items included with the lifts and stands) with the start date of the warranty beginning the date the units are received at the Tollway.

SPECIFICATION COMPLIANCE QUESTIONNAIRE

Vendor shall complete this specification compliance questionnaire and must return it with the bid. Failure to submit the specification compliance questionnaire will result in disqualification.

The lines below correlate to the specifications for the item(s) being purchased in this contract. Indicate below by marking “Yes” if the unit(s) being offered meets the specifications as noted for each specification line. Mark “No” if the unit(s) offered differs from any line specification. Please explain all specification differences. Vendor shall complete and return this form with the bid to be considered responsive. If no exceptions are noted, the Illinois Tollway will assume complete compliance with the specifications noted herein.

Company Name:________________________________________________________________

Please indicate the number of days to deliver the units after receipt of order:______________________

Mobile Column Lift Manufacturer:________________________Model:___________________________

Specify lift capacity: ______________________

CAB AND CHASSIS

1. _____Yes ____No if No, detail_________________________

2. _____Yes ____No if No, detail_________________________

3. _____Yes ____No if No, detail_________________________

4. _____Yes ____No if No, detail_________________________

5. _____Yes ____No if No, detail_________________________

6. _____Yes ____No if No, detail_________________________

7. _____Yes ____No if No, detail_________________________

8. _____Yes ____No if No, detail_________________________

9. _____Yes ____No if No, detail_________________________

10. _____Yes ____No if No, detail_________________________

11. _____Yes ____No if No, detail_________________________

12. _____Yes ____No if No, detail_________________________

13. _____Yes ____No if No, detail_________________________

14. _____Yes ____No if No, detail_________________________

15. _____Yes ____No if No, detail_________________________

16. _____Yes ____No if No, detail_________________________

17. _____Yes ____No if No, detail_________________________

18. _____Yes ____No if No, detail_________________________