2-Specification Sheet-Part 2001725.pdf

3B0115F

EN

Installation and Parts

QuikCut™ PCD Diamond Drums For removal of materials from flat horizontal concrete and asphalt surfaces. Use only with Graco® or SMITH® scarifiers. For professional use only.

See page 3 for model information.

Important Safety Instructions Read all warnings and instructions in this manual and in related manuals before using the equipment. Be familiar with the proper control and usage of the equipment.

Save these instructions.

Contents

2 3B0115F

Contents Related Manuals Models Safety Symbols General Warnings Component Identification Cut Width Adjustment Installation

Cutter Cartridge Replacement Recycling and Disposal

Parts GrindLazer Standard Series / SMITH FS200/20913 GrindLazer Pro-HP DC10 Series / SMITH SPS1014 GrindLazer Pro-HP DC15 Series / SMITH FS351

DCS

California Proposition 65 Graco Standard Warranty

Related Manuals Find English manuals and any available translations at www.graco.com or www.smithmfg.com.

English Manual Number

Description

3A5578 DC87, DC89, DC1013 Operation, Repair, Parts

3A5918 DC89, DC1013, DC1021 Operation 3A5919 DC89, DC1013, DC1021 Repair 3A5929 DC89, DC1013, DC1021 Parts 3A7600 DC1538, DC1525, DC1520 Operation, Repair, Parts 3A7832 SMITH FS351 Operation, Repair, Parts 3A6989 SMITH FS/SPS Series Operation, Repair, Parts

Models

3B0115F 3

Models Compatible Scarifiers Part Cut Width

(in.) Profile Drum Diameter (in.)

Hex Shaft size (in.)

Weight lbs (kg)

GrindLazer Standard Series

SMITH

FS200/209

2001721 6.9 Flat 5.5 0.75 27 (12.3)

2001720 6.9 Fine Groove 5.5 0.75 27 (12.3)

2003960 6.9 Coarse Groove 5.5 0.75 27 (12.3)

GrindLazer Pro-HP DC10

Series

SMITH SPS10

2001725 9.9 Flat 7.0 1.0 58 (26.3)

2001724 9.9 Fine Groove 7.0 1.0 58 (26.3)

2003962 9.9 Coarse Groove 7.0 1.0 58 (26.3)

2001723 5.4 Flat 7.0 1.0 54 (24.5)

2001722 5.4 Fine Groove 7.0 1.0 54 (24.5)

2003961 5.4 Coarse Groove 7.0 1.0 54 (24.5)

GrindLazer HP DC15 Series

SMITH FS351

DCS

2001727 15.2 Flat 10.0 1.5 138 (62.6)

2001726 15.2 Fine Groove 10.0 1.5 138 (62.6)

2003963 15.2 Coarse Groove 10.0 1.5 138 (62.6)

Safety Symbols

4 3B0115F

Safety Symbols The following safety symbols appear throughout this manual and on warning labels. Read the table below to understand what each symbol means.

Symbol Meaning

Burn Hazard

Cut Foot Hazard

Entanglement Hazard

Equipment Misuse Hazard

Flying Debris Hazard

Moving Parts Hazard

Toxic Fluid or Fumes Hazard

Read Manual

Wear Protective Footwear

Wear Personal Protective Equipment

Symbol Meaning

Safety Alert Symbol This symbol indicates: Attention! Become Alert! Look for this symbol throughout the manual to indicate important safety messages.

General Warnings

3B0115F 5

General Warnings The following warnings apply throughout this manual. Read, understand, and follow the warnings before using this equipment. Failure to follow these warnings can result in serious injury.

WARNING

DUST AND DEBRIS HAZARD

Grinding concrete and other surfaces with this equipment can create dust that contains hazardous substances. Grinding can also create flying debris.

To reduce the risk of serious injury:

• Control the dust to meet all applicable workplace regulations.

• Wear protective eye wear and a properly fit-tested and government approved respirator suitable for the dust conditions.

• Use equipment only in a well-ventilated area.

• Grinding equipment must be used only by trained personnel who understand the applicable workplace regulations.

ENTANGLEMENT AND ROTATING PARTS HAZARD

Rotating parts can cut or amputate fingers and other body parts.

• Keep clear of rotating parts.

• Do not operate equipment with protective guards or covers removed.

• Do not wear loose clothing, jewelry or long hair while operating equipment.

• Before checking, moving, or servicing equipment, disable power supply.

BURN HAZARD

Cutters and engine can become very hot during operation. To avoid severe burns, do not touch hot equipment. Wait until equipment has cooled completely.

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

• Do not operate the unit when fatigued or under the influence of drugs or alcohol.

• Do not leave the work area while equipment is energized. Turn off all equipment when equipment is not in use.

• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manufacturer’s replacement parts only.

• Do not alter or modify equipment.

• Use equipment only for its intended purpose. Call your distributor for information.

• Keep children and animals away from work area.

• Comply with all applicable safety regulations.

• Maintain a safe operating distance from other people in the work area.

• Avoid any pipes, columns, openings, or any other objects protruding from work surface.

PERSONAL PROTECTIVE EQUIPMENT

You must wear appropriate protective equipment when operating, servicing, or when in the operating area of the equipment to help protect you from serious injury, including eye injury, inhalation of dust or chemicals, burns, and hearing loss. This equipment includes but is not limited to:

• Protective eye wear.

• Protective shoes.

• Gloves.

• Hearing protection.

• Properly fit-tested and government approved respirator suitable for the dust conditions.

Component Identification

6 3B0115F

Component Identification

A Drum (1) B End Plate (2) C QuikCut PCD Cutter (21), (27), (39), or (80) D Cutter Bolt (21), (27), (39), or (80) E End Plate Bolt (8) or (12) F Pocket (27), (39), or (80)

Cut Width Adjustment

3B0115F 7

Cut Width Adjustment Add or remove cutters as described below to modify cut width.

Compatible Scarifiers Part Cut Width

in. (mm) # of Rows # of Cutters

GrindLazer Standard

Series

SMITH

FS200/209

2001721 2001720 2003960

6.9 (176) 9 27

• For each (3) cutters removed, this reduces the cut width by 0.75 in. (19.05mm).

• Always remove in incremenets of three (3), one entire row, to maintain drum balance.

• Removing an equal number of rows from each end of the drum will maintain the best drum balance.

• After removing the cutter, install the fastener back into location and torque.

• Periodically check the cutter bolts to ensure they are torqued to the specified value.

• Always use a new bolt with the threadlocking patch, or apply high strength threadlocker before reusing. See page 11.

• If excessive vibration occurs, STOP and investigate the issue.

* Populating the 7 rows between the two grooves will provide a 5.4 in. (138mm) cut width.

6.2 (157) 8 24

5.4 (138) 7 21

4.7 (119) 6 18

3.9 (100) 5 15

3.2 (81) 4 12

2.4 (62) 3 9

1.7 (43) 2 6

1.0 (24) 1 3

GrindLazer Pro-HP DC10

Series

SMITH SPS10

2001725 2001724 2003962 2001723 2001722 2003961

9.9 (252) 13 39

9.2 (233) 12 36

8.4 (214) 11 33

7.7 (195) 10 30

6.9 (176) 9 27

6.2 (157) 8 24

5.4 (138)* 7* 21*

4.7 (119) 6 18

3.9 (100) 5 15

3.2 (81) 4 12

2.4 (62) 3 9

1.7 (43) 2 6

1.0 (24) 1 3

Cut Width Adjustment

8 3B0115F

Compatible Scarifiers Part Cut Width

in. (mm) # of Rows # of Cutters

GrindLazer HP DC15 Series

SMITH FS351

DCS

2001727 2001726 2003963

15.2 (386) 20 80

• For each (4) cutters removed, this reduces the cut width by 0.75 in. (19.05mm).

• Always remove in increments of four (4), one entire row, to maintain drum balance.

• Removing an equal number of rows from each end of the drum will maintain the best drum balance.

• After removing the cutter, install the fastener back into location and torque.

• Periodically check the cutter bolts to ensure they are torqued to the specified value.

• Always use a new bolt with the threadlocking patch, or apply high strength threadlocker before reusing. See page 11.

• If excessive vibration occurs, STOP and investigate the issue.

14.4 (367) 19 76

13.7 (348) 18 72

12.9 (329) 17 68

12.2 (310) 16 64

11.4 (291) 15 60

10.7 (272) 14 56

9.9 (252) 13 52

9.2 (233) 12 48

8.4 (214) 11 44

7.7 (195) 10 40

6.9 (176) 9 36

6.2 (157) 8 32

5.4 (138) 7 28

4.7 (119) 6 24

3.9 (100) 5 20

3.2 (81) 4 16

2.4 (62) 3 12

1.7 (43) 2 8

1.0 (24) 1 4

Installation

3B0115F 9

Installation

Cutter Cartridge Replacement Replace chipped or damaged cutter cartridges to maintain cut quality and speed.

1. Switch off and unplug the power cord or disconnect spark plug wire and black battery cable (electric start models only).

2. Remove the three, four, or six bolts and the drum access panel.

Avoid touching or handling drum after use until it has completely cooled. To avoid injury from unexpected start up, switch off and unplug the power cord or disconnect spark plug wire and black battery cable (electric start models only) before you service the unit.

10 3B0115F

3. Slide drum completely off of hex shaft.

NOTE: Recommended if changing cut width, or replacing many or all cutter cartridges.

NOTE: If replacing a few or less cutter cartridges, the drum may be left completely on the shaft, or slide partially out for easier access.

4. Once the drum is removed, inspect the condition of all cutter cartridges, shaft, bushings, and drum.

5. Support drum using a hex shaft, or a pipe, secured in a vise, and remove any damaged cutter catridges using a 3/8” hex bit.

3B0115F 11

6. Install the new cutter cartridge using the new supplied 7/16-14x1.0” or 7/16-20x1.0” bolt, or apply high strength threadlocker, such as Loctite® 271, to the existing bolt, and tighten to the specified torque per the drum model using a 3/8” hex bit. See Parts, pages 13-14.

Approximate threadlocker cure times:

• Patch on bolt: 95% -12 hours; 100% - 72 hours

• Loctite 271: 100% - 24 hours

• Loctite 271 with Activator SF7649: 100% - 30 minutes

NOTE: Follow threadlocker manufacturer’s application instructions.

NOTE: An adjustable wrench can be used to hold the cutter straight in the pocket.

7. Before installing the drum onto the hex shaft:

a. Check that all bearings are in good working order.

b. Remove dirt and material build up from inside drive carriage and drum.

c. Lube all metal contacts.

d. Ensure drum is installed with cutter cartridges in correct direction for cutting per arrow on drum access panel.

8. Slide the drum back onto the shaft.

NOTICE

Installing drum in the wrong direction may cause damage to QuikCut PCD Cutters, the drum, and/or the scarifier.

12 3B0115F

9. Replace drum access panel (lift up and lock into place) over hex shaft and secure hardware.

Recycling and Disposal

End of Product Life At the end of a product’s useful life, recycle it in a responsible manner.

Parts

3B0115F 13

Parts GrindLazer Standard Series / SMITH FS200/209

2001721

Parts List

2001720

Parts List

2003960

Parts List

Ref. Part Description Qty 1 2004425 KIT, drum, bare, small 1 2 2003680 KIT, cartridge, flat includes qty. 1

Bolt 2001525 and 2007635

3 2007635 BOLT, shcs, 7/16-20 x 1 in. 27

Ref. Part Description Qty 1 2004425 KIT, drum, bare, small 1 2 2003681 KIT, cartridge, fine groove includes qty. 1 Bolt 2001525 and 2007635

3 2007635 BOLT, shcs, 7/16-20 x 1 in. 27

Ref. Part Description Qty 1 2004425 KIT, drum, bare, small 1 2 2004029 KIT, cartridge, coarse groove includes qty. 1 Bolt 2001525 and 2007635

3 2007635 BOLT, shcs, 7/16-20 x 1 in. 27

NOTICE

Using the wrong bolt will cause damage to the drum threads. Ensure the correct fine or coarse thread bolt is being used to install the new QuikCut PCD cutter.

2001525 Silver Coarse Thread Bolt, torque to 75 ± 5 ft-lb (95 -108 N·m) 2007635 Black Fine Thread Bolt, torque to 85 ± 5 ft-lb (108 -122 N·m)

1 2001525 Silver Coarse Thread Bolt, torque to 75 ± 5 ft-lb (95 -108 N·m) 2007635 Black Fine Thread Bolt, torque to 85 ± 5 ft-lb (108 -122 N·m)

2001525 Silver Coarse Thread Bolt, torque to 75 ± 5 ft-lb (95 -108 N·m) 2007635 Black Fine Thread Bolt, torque to 85 ± 5 ft-lb (108 -122 N·m)

Marked “7/16-20” for fine thread bolt 20076352 Marked “7/16-20” for fine thread bolt 20076352

Marked “7/16-20” for fine thread bolt 20076352

14 3B0115F

GrindLazer Pro-HP DC10 Series / SMITH SPS10

2001725

Parts List

2001724

Parts List

2003962

Parts List

2001723

Parts List

Ref. Part Description Qty 1 2004426 KIT, drum, bare, medium 1 2 2003680 KIT, cartridge, flat includes qty. 1

Bolt 2001525 and 2007635

3 2007635 BOLT, shcs, 7/16-20 x 1 in. 39

Ref. Part Description Qty 1 2004426 KIT, drum, bare, medium 1 2 2003681 KIT, cartridge, fine groove includes qty. 1 Bolt 2001525 and 2007635

3 2007635 BOLT, shcs, 7/16-20 x 1 in. 39

Ref. Part Description Qty 1 2004426 KIT, drum, bare, medium 1 2 2004029 KIT, cartridge, coarse groove includes qty. 1 Bolt 2001525 and 2007635

3 2007635 BOLT, shcs, 7/16-20 x 1 in. 39

Ref. Part Description Qty 1 2004426 KIT, drum, bare, medium 1 2 2003680 KIT, cartridge, flat includes qty. 1

Bolt 2001525 and 2007635

3 2007635 BOLT, shcs, 7/16-20 x 1 in. 39

2001525 Silver Coarse Thread Bolt, torque to 75 ± 5 ft-lb (95 -108 N·m) 2007635 Black Fine Thread Bolt, torque to 85 ± 5 ft-lb (108 -122 N·m)

1 2001525 Silver Coarse Thread Bolt, torque to 75 ± 5 ft-lb (95 -108 N·m) 2007635 Black Fine Thread Bolt, torque to 85 ± 5 ft-lb (108 -122 N·m)

2001525 Silver Coarse Thread Bolt, torque to 75 ± 5 ft-lb (95 -108 N·m) 2007635 Black Fine Thread Bolt, torque to 85 ± 5 ft-lb (108 -122 N·m)

1 2001525 Silver Coarse Thread Bolt, torque to 75 ± 5 ft-lb (95 -108 N·m) 2007635 Black Fine Thread Bolt, torque to 85 ± 5 ft-lb (108 -122 N·m)

3B0115F 15

2001722

Parts List

2003961

Parts List Ref. Part Description Qty 1 2004426 KIT, drum, bare, medium 1 2 2003681 KIT, cartridge, fine groove includes qty. 1 Bolt 2001525 and 2007635

3 2007635 BOLT, shcs, 7/16-20 x 1 in. 39

Ref. Part Description Qty 1 2004426 KIT, drum, bare, medium 1 2 2004029 KIT, cartridge, coarse groove includes qty. 1 Bolt 2001525 and 2007635

3 2007635 BOLT, shcs, 7/16-20 x 1 in. 39

NOTICE

Using the wrong bolt will cause damage to the drum threads. Ensure the correct fine or coarse thread bolt is being used to install the new QuikCut PCD cutter.

2001525 Silver Coarse Thread Bolt, torque to 75 ± 5 ft-lb (95 -108 N·m) 2007635 Black Fine Thread Bolt, torque to 85 ± 5 ft-lb (108 -122 N·m)

1 2001525 Silver Coarse Thread Bolt, torque to 75 ± 5 ft-lb (95 -108 N·m) 2007635 Black Fine Thread Bolt, torque to 85 ± 5 ft-lb (108 -122 N·m)

16 3B0115F

GrindLazer Pro-HP DC15 Series / SMITH FS351 DCS

2001727

Parts List

2001726

Parts List

2003963

Parts List

Torque to 85 ± 5 ft-lb (108-122 N·m)

Ref. Part Description Qty 1 2004427 KIT, drum, bare, large 1 2 2003680 KIT, cartridge, flat includes qty. 1

Bolt 2001525 and 2007635

3 2007635 BOLT, shcs, 7/16-20 x 1 in. 80

Torque to 85 ± 5 ft-lb (108-122 N·m)

Ref. Part Description Qty 1 2004427 KIT, drum, bare, large 1 2 2003681 KIT, cartridge, fine groove includes qty. 1 Bolt 2001525 and 2007635

3 2007635 BOLT, shcs, 7/16-20 x 1 in. 80

Torque to 85 ± 5 ft-lb (108-122 N·m)

Ref. Part Description Qty 1 2004427 KIT, drum, bare, large 1 2 2004029 KIT, cartridge, coarse groove includes qty. 1 Bolt 2001525 and 2007635

3 2007635 BOLT, shcs, 7/16-20 x 1 in. 80

California Proposition 65

3B0115F 17

California Proposition 65

CALIFORNIA RESIDENTS

WARNING: Cancer and reproductive harm – www.P65warnings.ca.gov.

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

Original instructions. This manual contains English. MM 3B0115 Graco Headquarters: Minneapolis

International Offices: Belgium, China, Japan, Korea

GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA

Copyright 2024, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.

www.graco.com Revision F, January 2025

Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS

The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.

Graco Information For the latest information about Graco products, visit www.graco.com.

For patent information, see www.graco.com/patents.

TO PLACE AN ORDER, contact your Graco distributor or call 1-800-690-2894 to identify the nearest distributor.