22R0069_Attachment J.1.E Specification Information.pdf

Base Flexibility The base is designed to form a seal on most panel configurations and roof pitches regardless of pipe location.

Slide Over Pipe Form to Roof Profile Apply Sealant Fasten to Complete

1 2 3 4 5

Master Flash® was used to create a new engineering standard for profiled roofing by the International Association of Plumbing and Mechanical Officials (for the Uniform Plumbing Code) and remains the only product listed.

These products are also listed for use with Type B vents.

The addition of fire retarding agents milled directly into the rubber compound created a self extinguishing feature which enables it to be used with type “B” vents. Listed with IAPMO certification No. 3121

STANDARD MASTER FLASH®

I A P M O ®

FOUNDED 1926

U PC

Designated pipe size molded on flashing

Weather Protection Made of E.P.D.M. or Silicone, these flashings are compounded specifically for maximum resistance to weathering due to ozone and ultraviolet light.

Easy On Site Customization

Fast, one piece construction allows for easy on-site installation in usually 5 minutes.

Design Excellence Aztec’s flexible design meets all roofing needs.

Sleeve flexibility accommodates vibration and pipe movement caused by expansion/contraction. The soft aluminum base easily conforms to roof panels.

Choose Pipe Opening and Trim

STANDARD MASTER FLASH®

TERRA COTTA

BLACK

DARK BLUE

BROWN

WHITE

GREY

LIGHT GREEN

BRIGHT RED

LIGHT BLUE

DARK GREEN

ISO Quality, Price & Availability

SIZING CHART

Check diameter of pipe. Select the appropriate Master Flash® for pipe or duct diameter. For extreme pitch or surface irregularity select next larger size. Choose the compound required, then refer to the part number for the Master Flash® desired.

*Complete specification data and testing methods are available upon request.

TWO COMPOUNDS/ 11 SIZES & 10 COLORS

“Available in two compounds to handle virtually all job applications”

EPDM SILICONE

ADVANCED OZONE RESISTANCE tested to... 70 hour @ 500 pphm 70 hour @ 500 pphm

HIGH TEMPERATURE RESISTANCE

Tested to Intermittent +135°C (+275°F) +260°C (+500°F)

Continuous +100°C (+212°F) +225°C (+437°F)

LOW TEMPERATURE RESISTANCE tested to... (-65°F)

– 55°C –74°C (–100°F)

TENSILE SET maximum 1OMPa (1450 psi) 5 MPa (700 psi)

COMPRESSION SET maximum... 25% 50%

Mini

#1

#2

#3

#4

#5

#6

#7

#8

#9

Maxi

1/8”– 3/4” (3.2mm - 19.1 mm)

1/4”- 2-3/4” (6.4mm - 70.0mm)

1”- 4” (25mm - 101.5mm)

1/4” - 5-1/2” (6.4mm - 114.2mm)

3” - 7” (76.2mm - 177.8mm)

4” - 8-1/4” (101.5mm - 209.5mm)

5” - 9-1/2” (127mm - 241.3mm)

5-1/2” - 11-1/2” (114.2mm - 292.0mm)

7” - 13-1/2” (177.8mm - 343.3mm)

9-1/2” - 20-1/2” (251.3mm - 520.7mm)

13” - 28-1/2” (330.2mm - 723.9mm)

A-Top opening diameter 1/16” (1.6mm) B-Cut to suit pipe size 1/8” – 3/4” (3.2-19.1mm)

2 - 1/4” (57.2mm) C-Base dimensions Closed 1/4” – 2-3/4” (6.4-70.0mm) 4-1/2” (114.3mm) 7/8” (22.2mm) 1” - 4” (25-101.5mm) 6” (152.4mm) Closed 1/4” – 5-1/2” (6.4-114.2mm) 8” (203.2mm) 2-1/2” (63.5mm) 3”– 7” (76.2-177.8mm) 10” (254mm) 3-1/2” (88.9mm) 4” – 8-1/4” (101.5-209.5mm) 11” (279.4mm) 4” (101.6mm) 5” – 9-1/2” (127-241.3mm) 12” (304.8mm) 5” (127mm) 5-1/2” – 11-1/2” (114.2-292.0mm) 14” (355.6mm) 6” (152.4mm) 7” – 13-1/2” (177.8-343.3mm) 17” (431.8mm) 8-1/2” (215.9mm) 9-1/2” – 20-1/2” (254-520.7mm) 25” (635mm) 11” (279.4mm) 13” – 28-1/2” (330.2-723.9mm) 34” (863.6mm)

BLACK EPDM SQ051BA

BLACK EPDM

GREY EPDM

SILICONE

SQ101BA

SQ101GA

SQ102RA

BLACK EPDM

GREY EPDM

SILICONE

SQ201BA

SQ201GA

SQ202RA

BLACK EPDM

GREY EPDM

SILICONE

SQ301BA

SQ301GA

SQ302RA

BLACK EPDM

GREY EPDM

SILICONE

SQ401BA

SQ401GA

SQ402RA

BLACK EPDM

GREY EPDM

SILICONE

SQ501BA

SQ501GA

SQ502RA

BLACK EPDM

GREY EPDM

SILICONE

SQ601BA

SQ601GA

SQ602RA

BLACK EPDM

GREY EPDM

SILICONE

SQ701BA

SQ701GA

SQ702RA

BLACK EPDM

GREY EPDM

SILICONE

SQ801BA

SQ801GA

SQ802RA

BLACK EPDM

GREY EPDM

SILICONE

SQ901BA

SQ901GA

SQ902RA

BLACK EPDM

GREY EPDM

SILICONE

SQ951BA

SQ951GA

SQ952RA

Pipe Size Compound Part No.

A-Top opening diameter B-Cut to suit pipe size C-Base dimensions A-Top opening diameter B-Cut to suit pipe size C-Base dimensions A-Top opening diameter B-Cut to suit pipe size C-Base dimensions A-Top opening diameter B-Cut to suit pipe size C-Base dimensions A-Top opening diameter B-Cut to suit pipe size C-Base dimensions A-Top opening diameter B-Cut to suit pipe size C-Base dimensions A-Top opening diameter B-Cut to suit pipe size C-Base dimensions A-Top opening diameter B-Cut to suit pipe size C-Base dimensions A-Top opening diameter B-Cut to suit pipe size C-Base dimensions A-Top opening diameter B-Cut to suit pipe size C-Base dimensions

Flashing Details

Distributed by: BEST MATERIALS LLC, Phoenix AZ 602-272-8128 800-474-7570 www.bestmaterials.com Email: Sales@bestmaterials.com

CNwankwo Rectangle

Retrofit Pipe Flashing Boots http://www.bestmaterials.com/retrofit_pipe_flashing_boots.aspx[9/8/2010 3:51:38 PM]

Log-In Log-Out Home About Us Contact Us FAQ Products Shipping Terms Order Help

Search

Advanced Search

Shopping Cart:

0 Items In Cart Total: $0.00

Adhesives

Backer Rod

Caulk & Sealants

Clean Up

Concrete Items

Deck Coatings

Drains

EPDM

Fasteners

Hardware & LPG

Metal Goods

Paint & Tape

Pipe Flashings

Roof Coatings

Roof Hatch/Vent

Roof Repair

Roof Tiles

Safety Products

Support Systems

Tarps

TPO / PVC

Tool Accessories

Tools & Equip.

Underlayments

Waterproofing

We feature all types of heavy duty rubber retrofit pipe flashings from the best manufacturers including Master flash and Spring Seal. Retrofit pipe flashings enable your to wrap the boot around an existing structure to waterproof it. We inventory all sizes of both black EPDM and red Silicone flashing boots. Also we have the new square-tube / duct flashings.

Silicone and EPDM materials properties are here.

And we also carry Retro-Spins: retrofits for electrical conduit entry on roofs (roof jacks).

For irregular or multiple penetrations in one area, see our roof penetrations page for additional options. You'll find a solution there.

Contact us for special pricing and delivery on volume orders.

Questions? email sales@bestmaterials.com or call 1-800-474-7570 You'll get a prompt reply.

RETROFIT SQUARE-BOTTOM PIPE FLASHING BOOTS

(used on standing seam roofs to wrap around an existing pipe which cannot have a boot slipped over the top) (click on Part# to get pricing and details)

Selection: Check the outside diameter of pipe. Click on the appropriate Part# for your pipe diameter to get the pricing and detailed specifications. For high pitch or surface irregularity, select the largest size which fits your pipe.

Part # Fits Pipe Sizes (dia. inches)

Boot Compound

Boot Color

Flashing Boot Size (inches) Top

Opening Height Base

RF-ZPS-1E 1/8 - 4-1/2 EPDM Black 1/8 8.25x9 Rect.RF-ZPS-1S SILICONE Red

1RF

1/2 - 4 EPDM Black

1/2 5 8.18 Sq1RFG EPDM Gray 1RFS SILICONE Red

3MF-E

2 - 4-1/2 EPDM Black

Closed 8 Sq3MF-EG EPDM Gray 3MF-S SILICONE Red

5MF-E

4 - 7 EPDM Black

3-1/2 11 Sq5MF-EG EPDM Gray 5MF-S SILICONE Red

2RF

4 - 9-1/4

EPDM Black 4 14.25 Sq2RFG EPDM Gray

2RFS SILICONE Red

8MF-E

7 - 13 EPDM Black

6 17 Sq8MF-EG EPDM Gray

Recent Views Pages retrofit pipe flashing boots masterflash sizes and materials

EPDM-Roofing masterflash sizes and materials http://www.bestmaterials.com/CustSignIn.aspx http://www.bestmaterials.com/CustSignIn.aspx?Signout=1 http://www.bestmaterials.com/default.aspx http://www.bestmaterials.com/about_us.aspx http://www.bestmaterials.com/contact.aspx http://www.bestmaterials.com/FAQ.aspx http://www.bestmaterials.com/sitemap.aspx http://www.bestmaterials.com/shipping.aspx http://www.bestmaterials.com/Terms.aspx http://www.bestmaterials.com/OrderEntryHelp.aspx javascript:__doPostBack('LeftColumnNav1$SimpleSearch1$btnSearch','') http://www.bestmaterials.com/Search-Advanced.aspx http://www.bestmaterials.com/shoppingcart.aspx http://www.bestmaterials.com/default.aspx http://www.bestmaterials.com/# http://www.bestmaterials.com/adhesives.aspx http://www.bestmaterials.com/Backer_Rod.aspx http://www.bestmaterials.com/caulk_sealants.aspx http://www.bestmaterials.com/clean_up.aspx http://www.bestmaterials.com/cement_Sand.aspx http://www.bestmaterials.com/deck_coatings.aspx http://www.bestmaterials.com/drains.aspx http://www.bestmaterials.com/EPDM-Roofing.aspx http://www.bestmaterials.com/fasteners.aspx http://www.bestmaterials.com/hardware.aspx http://www.bestmaterials.com/metal_goods.aspx http://www.bestmaterials.com/paint_tape.aspx http://www.bestmaterials.com/penetration_seals.aspx http://www.bestmaterials.com/roof_coatings.aspx http://www.bestmaterials.com/Skylight_Hatch.aspx http://www.bestmaterials.com/roof_repair.aspx http://www.bestmaterials.com/Green_Roof_Plastic_Roof_Tiles.aspx http://www.bestmaterials.com/safety_products.aspx http://www.bestmaterials.com/Supports_stands.aspx http://www.bestmaterials.com/tarps.aspx http://www.bestmaterials.com/Single-Ply-Roofing.aspx http://www.bestmaterials.com/tool_accessories.aspx http://www.bestmaterials.com/tools_equipment.aspx http://www.bestmaterials.com/web_fabrics.aspx http://www.bestmaterials.com/waterproofing.aspx http://www.bestmaterials.com/Manufacturers.aspx http://www.bestmaterials.com/SearchResult.aspx?categoryid=1176 http://www.bestmaterials.com/masterflash-rubber-pipe-flashings-683.html http://www.bestmaterials.com/masterflash_sizes_and_materials.aspx#PIPE FLASHING BOOT MATERIALS PROPERTIES http://www.bestmaterials.com/Roof_Jack.aspx http://www.bestmaterials.com/penetration_seals.aspx mailto:sales@bestmaterials.com http://www.bestmaterials.com/masterflash_sizes_and_materials.aspx#PIPE FLASHING BOOT MATERIALS PROPERTIES http://www.bestmaterials.com/detail.aspx?ID=16154 http://www.bestmaterials.com/detail.aspx?ID=16155 http://www.bestmaterials.com/detail.aspx?ID=8946 http://www.bestmaterials.com/detail.aspx?ID=17780 http://www.bestmaterials.com/detail.aspx?ID=14993 http://www.bestmaterials.com/detail.aspx?ID=17100 http://www.bestmaterials.com/detail.aspx?ID=17099 http://www.bestmaterials.com/detail.aspx?ID=14954 http://www.bestmaterials.com/detail.aspx?ID=17781 http://www.bestmaterials.com/detail.aspx?ID=14992 http://www.bestmaterials.com/detail.aspx?ID=17098 http://www.bestmaterials.com/masterflash_sizes_and_materials.aspx http://www.bestmaterials.com/masterflash_sizes_and_materials.aspx http://www.bestmaterials.com/masterflash_sizes_and_materials.aspx http://www.bestmaterials.com/EPDM-Roofing.aspx http://www.bestmaterials.com/masterflash_sizes_and_materials.aspx http://www.bestmaterials.com/masterflash_sizes_and_materials.aspx http://www.bestmaterials.com/masterflash_sizes_and_materials.aspx CNwankwo Text Box

FOR PIPES WITH BEND/GOOSE NECK

http://www.bestmaterials.com/retrofit_pipe_flashing_boots.aspx[9/8/2010 3:51:38 PM]

Shop With

Confidence

8MF-S SILICONE Red

3RF

9-1/4 - 16-1/4 EPDM Black

9-1/4 21.5 Sq3RFG EPDM Gray 3RFS SILICONE Red

MAXI-RF 13 - 28 EPDM Black 11.5 34 SqMAXI-RFS SILICONE Red

1RF-SQ 2-1/2 - 4"

SQUARE TUBE

EPDM Black 2.4 5.25

2RF-SQ 2-1/4 - 5"

SQUARE TUBE

EPDM Black 2.2 7

Installation instructions for retrofit pipe flashing boots Product Datasheet for Retrofit Boots Submittal Spec for Master Flash Boots

RETROFIT ROUND-BOTTOM PIPE FLASHING BOOTS

Lower Cost, Smaller Sized, With Improved "Zip-Seal" Edge Seal with Clip Includes Stainless Steel Zip Clips.

Selection: Check the outside diameter of pipe to get pricing and detailed specifications. Click on the appropriate Part# for your pipe diameter to get pricing and detailed information. For high pitch roofs, select next largest size which fits your pipe.

Part # Fits Pipe

Sizes (dia. inches)

Boot Compound

Boot Color

Flashing Boot Size (inches) Top

Height Base Diameteropening

RF-ZRS-E

3/4 to 2-3/4

EPDM Black 3/4 3-1/4 6-1/4

RF-ZP-R-S SILICONE Red

RF-ZRM-E

2 to 7-1/2 EPDM Black

2 10-3/4 RF-ZP-R-M SILICONE Red

RF-ZRL-E

3-1/4 to 10 EPDM Black

3-1/4 14-1/2 RF-ZP-R-L SILICONE Red

1 to 3 1 5.5 1112015 NEOPRENE* Black

3-1/2 to 6 3-1/2 5 14-1/212025 NEOPRENE* Black

* For BUR, Tar, Hot Applied and Bitumen roofing.

Multi-Flash square-bottom retrofit flashing. Similar to the round-bottom design above but with a bigger footprint for standing seam roofs. They feature a lower cost design with improved sealing. Available in sizes to fit 2" to 26" OD pipes.

http://verify.authorize.net/anetseal/?pid=499e9ea4-f577-4c6e-9eb4-f9635e929d0a&rurl=http%3A//www.bestmaterials.com/retrofit_pipe_flashing_boots.aspx http://www.authorize.net/ http://www.authorize.net/ http://www.bestmaterials.com/detail.aspx?ID=14955 http://www.bestmaterials.com/detail.aspx?ID=17782 http://www.bestmaterials.com/detail.aspx?ID=14994 http://www.bestmaterials.com/detail.aspx?ID=17281 http://www.bestmaterials.com/detail.aspx?ID=17077 http://www.bestmaterials.com/detail.aspx?ID=16449 http://www.bestmaterials.com/detail.aspx?ID=16450 http://www.bestmaterials.com/retrofit_masterflash_install.aspx http://www.bestmaterials.com/PDF_Files/Masterflash-retro-datasheets.pdf http://www.bestmaterials.com/PDF_Files/Master-Flash-Submittal.pdf http://www.bestmaterials.com/masterflash_sizes_and_materials.aspx#PIPE FLASHING BOOT MATERIALS PROPERTIES http://www.bestmaterials.com/detail.aspx?ID=16028 http://www.bestmaterials.com/detail.aspx?ID=16151 http://www.bestmaterials.com/detail.aspx?ID=16029 http://www.bestmaterials.com/detail.aspx?ID=16152 http://www.bestmaterials.com/detail.aspx?ID=16030 http://www.bestmaterials.com/detail.aspx?ID=16153 http://www.bestmaterials.com/detail.aspx?ID=10839 http://www.bestmaterials.com/SearchResult.aspx?KeyWords=multi-flash

Technical Data Guide Polyether Technology CSI Section No. 07 92 13

Last Revision: 09/14/09Chem Link Inc.

Telephone: 800-826-1681

Fax: 269-679-4448

353 East Lyons

Schoolcraft, MI 49087 www.chemlinkinc.com

Applicable Performance Standards

• ASTM C-920, Type S, Grade NS, Class 50, Uses NT, T, M, G, A, and O

• Federal Specification TT-S-00230-C Type II, Class A

• Corps of Engineers CRD-C-541, Type II, Class A

• Canadian Standards Board CAN 19, 13-M82

• SWR

• AAMA 802.3-08 Type II, AAMA 803.3-08 Type I, and

AAMA 805.2-08 Group C.

Institute Validated (Sealant Waterproofing and

Restoration)

Product Description DuraLink is an extremely elastic moisture curing sealant designed for use in metal architecture, curtain wall construction and joints subject to movement.

DuraLink’s adhesion to difficult surfaces permits its use on anodized metal, and coatings such as

Kynar 500® PVDF. DuraLink will not stain limestone, marble, or other absorbent stone substrates.

DuraLink’s unique polyether chemistry eliminates outgassing on green concrete and “suntanning” or discoloration after exposure to ultraviolet light.

Advantages

• Bonds to Kynar 500® PVDF coated metal

• Solvent free, 100% solids will not shrink

• Non-slump, applies vertically and overhead

• 30 minute skin over, no dirt pick up

• No outgassing on damp surfaces

• Color stability, will not suntan

• Paintable within 24 hours (See limitations)

• +/- 50 joint movement

Regulatory Compliance

• Conforms to OTC Rule for Sealants and Caulks

• Meets requirements of California Regs:

BAAQMD, CARB and SCAQMD

• Conforms to California Proposition 65

Green Standards

• LEED 2009 for New Construction and Major

Renovations: Low Emitting Materials (Section 4.1)

1 Point

• NAHB Model Green Home Building Guidelines:

5 Global Impact Points

• VOC Content at 240° F: less than 19 grams/liter

(including water), ASTM D2369, EPA Method 24

Packaging

• 10.1 oz (300 ml)

24 cartridges/carton, 45 cartons/pallet

• 20 oz (825 ml) 12 sausages/carton, 45 cartons/pallet

• 5 gallon pails and 50 gallon drums available by special order

Colors Bronze Dark Bronze Black

Forest Green Stone Gray

Terra Cotta Aluminum Limestone

Tan Almond White

DuraLink The Next Generation Sealant

Super Adhesion Sealant

* Color matching is available in batch quantity only

Distributed by: BEST MATERIALS LLC 602-272-8128 800-474-7570 Email: Sales@bestmaterials.com www.bestmaterials.com

Joint Design Install all joint applications per ASTM and SWRI recommendations and guidelines. Joints shall be designed with a depth to width ratio of 1:2 (joint depth one-half the width). Control the depth of the sealant by using a polyethylene backer rod that is 25% larger than the joint opening at standard temperature.To prevent three-point adhesion use a backer rod or bond breaker tape to ensure proper joint movement and a long lasting weatherproof seal.

Where the joint configuration will not permit a backer rod, Chem Link recommends that an alternative bond breaker be used.

Joint Preparation Joint surfaces should be clean, dry and free from all contamination including: dirt, oils, grease, tar, wax, rust and any other substance that may inhibit the sealant’s performance.

Joint Width Joint Depth Inches (mm) Inches (mm)

1/4 - 1/2 (6-13) 1/4 (6)

1/2 - 3/4 (13-19) 1/4 - 3/8 (6-10)

3/4 - 1 (19-25) 3/8 - 1/2 (10-13)

1 - 2 (25-50) 1/2 (13)

Typical Uncured Properties

Gun Grade Zero Slump ASTM C 697

Viscosity 750,000+ cps Brookfield RVF, TF spindle, 4 RPM, 73° F

Tack Free Time 35 minutes - ASTM C-679

Odor Mild Mint Smell

*Test and evaluate to ensure adequate adhesion.

Basic Uses Expansion Joints

Pre-cast Concrete

Block and Masonry

Curtain Walls

Window and Door Frames

Siding

Parapets

Cove Joints

Transportation

Weather Sealing

Compatible Substrates* Kynar 500® PVDF Coated Metal

Galvanized Metal

Aluminum

Engineered Plastics, PVC

Glass

Fiberglass FRP

EPS Foam

EPDM and SBS Mod Bit

Block and Brick

Concrete and Stone

Typical Cured Properties

Elongation at Break 750 - 800% ASTM D-412

Hardness Shore A 20 +/- 3 ASTM C-661

Shear Strength 150 PSI ASTM D-1002

Shelf Life Cartridges: 1 year Sausages: 1 year Pails: 3 months

Tensile Strength 250 - 300 PSI ASTM D-2370

Service Temperature

Minus 40° F to 200° F continuous service

Shrinkage No measurable shrinkage after 14 days

Low Temperature Flex

Minus 10° F pass ¼ inch mandrel

ASTM D-816

Application Guidelines

Metal Prepare all metal to ensure maximum adhesion.

Remove all rust, scale and residue by wire brushing to a bright metal sheen. Remove films, loose or inappropriate coatings and oils with an appropriate solvent such as alcohol.*

*Chem Link recommends that coated substrates be tested for adhesion prior to starting a project. Please contact Technical Services for specific application guidelines and recommendations.

Concrete Prior to application remove any residual contamination by mechanical abrasion, sand blasting or power washing.

On green concrete, remove all release agents, friable and loose concrete. Dry all visible and standing water prior to applying DuraLink. Install an appropriate backer rod to avoid three-point bonding.

Wood Wood should be clean, sound and dry prior to sealant application. Allow treated wood to weather for six months prior to application. Remove all coatings and paint (or test for compatibility) to ensure proper bonding. Do not use on fire retardant lumber.

Priming In most instances DuraLink will not require a primer.

However, certain applications or substrates may require a primer to ensure a long lasting bond and weatherproof seal. It is the applicator’s responsibility to determine the need for a primer. Chem Link recommends a primer be used for any application where prolonged immersion is anticipated.

Limitations

• In areas where prolonged chemical exposure is anticipated, contact Technical Services for recommendations.

• Allow treated wood to “cure” for six months prior to application per APA guidelines.

• Do not use in areas subject to continuous immersion.

• Do not store in elevated temperatures.

• Remove all coatings and sealers before application.

• Do

Test and evaluate all paints before applying. Alkyd and oil based paints may dry slowly.

Do not use on TPO without Chem Link TPO primer.

not apply at temperatures below 30° F.

Caution Avoid prolonged contact with skin. Uncured adhesive irritates eyes. In case of contact with eyes, immediately flush with water. Call a physician.

Please refer to the MSDS for First Aid information.

Most current MSDS can be found at www.chemlinkinc.com.

KEEP OUT OF REACH OF CHILDREN.

Shelf Life One year from date of manufacture when stored in normal environments. High temperature and high relative humidity may significantly reduce shelf life.

Pails and special orders have a shelf life of three months.

Storage Store original, unopened containers in a cool, dry area. Protect unopened containers from water, heat and direct sunlight. Elevated temperatures will reduce shelf life. DuraLink will not freeze.

Clean-Up Wet sealant can be removed using a solvent such as alcohol. Cured DuraLink can be removed by abrading or scraping the substrate.

Application Instructions Remove all dirt, oil, loose paint, frost and other contamination from all working surfaces with alcohol.

DO NOT USE petroleum solvents such as mineral spirits or xylene. Maintain DuraLink at room temperature before applying to ensure easy gunning and leveling. Test and evaluate to ensure adequate adhesion. Carefully gun the sealant with a smooth, continuous bead. If tooling is needed, do so within fifteen minutes of application. Do not use on Hypalon membranes. On TPO, use Chem Link TPO primer. On smooth APP, torch apply a granulated APP target piece around penetration(s) before installing ChemCurbs.

Do not prime bonding surfaces with asphalt primer! Do not use asphalt cement as a “night sealant.”

EVERGRIP™ Stainless Fasteners EVERGRIP stainless bi-metal For metal to wood

Weather Gard® Metal to Wood

SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0502-0508 ©2008 SFS intec, Inc.

EVERGRIP stainless wood fastener is designed to self-drill metal panels:

• Head and the majority of shank is 304 Stainless Steel, with a welded, hardened carbon steel point for self-drilling performance.

• Provides the corrosion protection of stainless with the drill performance of a carbon steel fastener.

• Designed specifically for corrosion resistance in new wood treatments (ACQ/CA).

Application

EVERGRIP

9 – 15 HWH Sharp Point Assembled with stainless Bond Seal Metal to wood Drilling capacity: 24 ga (0.024) Self-drills through the metal panel and taps into wood substrate.

Min penetration in wood substrates should be no less than 1"

EVERGRIP

9 – 15 T-25 (TORX®) Pan Head Assembled with stainless Bond Seal Metal to wood Drilling capacity: 24 ga. (0.024) Self-drills through the metal panel and taps into wood substrate.

Min penetration in wood substrates should be no less than 1"

Performance Pounds Ultimate Pull-out (lbs ult.)

Wood: Spruce, Pine, Fir

EVERGRIP Stainless Bond Seal 1-1/2" Penetration 748 1" Penetration 542

Notes: Dimensions are nominal inches unless noted. Pull out strength values may vary from tabulated loads depending upon specific wood density variations.

Pull over strength values are based on AZ55 Galvalume steel material.

Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied.

Selection HWH HWH T-25 Pan Head Length 250/Bag 100/Box 250/Bag

1" E4160-CUF E4160-CUEG 1119934

1-1/2" E4260-CUF E4260-CUEG 1124180

2" E4380-CUF E4380-CUEG 1119937

2-1/2" E4460-CUF E4460-CUEG —

3" — — 1119938

Description Part No. Quantity SFS Special T-25 Torx drive bit 0514261 1 each

File Name: WG6.3_E4160.eps Created by: EWB-11/27/02

Revised: MPD-00/00/02

POSITIVE reduced 00%

NEGATIVE reduced 00%

Installation Tools: 0 – 2500 rpm screwdriver equipped with depth sensing nosepiece.

The EVERGRIP 9-15 T-25 (TORX) Pan Head requires a T-25 Torx drive bit.

Utilizing the special SFS T-25 Torx drive bit manufactured by SFS intec is recommended for superior stability during the installation process.

Options Painted

ZAC MAC PRISMA irius

ZAC® MAC™ Prisma™ irius Painted Sentri™ BI-METALSX

5 6 7 3 2 1 ?4

Stainless Self Drilling

File Name: WeatherGard_icons.eps Created by: EB-11/18/02 Revised: MPD-12/02/02

1/4" Hex Washer Head Thread Major Dia: 0.181 – 0.175 Thread Minor Dia: 0.133 – 0.127 Strength (lbs ult.):

Tensile: 1657 Torsional: 50 in-lbs min.

Shear: 1550

Pull-over

28 ga: 378 26 ga: 519 24 ga: 704

POSITIVE reduced 00%

NEGATIVE reduced 00% File Name: P_1481A_E.eps

Created by:EWB-04/8/08 Revised: MPD-00/00/08

T-25 (TORX) Pan Head Head Dia: 0.393–0.374” Thread Major Dia: 0.181 – 0.175 Thread Minor Dia: 0.133 – 0.127 Strength (lbs ult.):

Tensile: 1657 Torsional: 50 in-lbs min.

Shear: 1550 Utilizing the special SFS T-25 Torx drive bit manufactured by SFS intec is recommended for superior stability during the installation process.

Fasteners installed in less than 1" of solid wood may have an increased potential for sealing or connection failure over time. This may be due to the fasteners being stripped out during installation and/or due to the lack of adequate wood fiber material to hold the fastener in place during thermal movement cycles or other forces which may be exerted upon the connection.

SECTION 13126 – PRE-ENGINEERED BUILDING SYSTEMS

TAB C – SHOP DRAWING INDEX

ITEM VENDOR/MANUFACTURER PAGE

ANCHOR BOLT SETTING PLAN MAMMUT BUILDING SYSTEMS

WWW.MAMMUTGROUP.COM

RIGID FRAME CROSS SECTION @

GL-2,3,4,5 & 6

ROOF RAMING PLAN 4

SIDE WALL FRAMING ELEVATION

ALONG GL-D AND GL-A

END WALL FRAMING ELEVATION @

GL-1

ROOF SHEETING PLAN & DETAILS 7

SIDE WALL SHEETING ELEVATION

ALONG GL-A

END WALL SHEETING ELEVATION @

GL-1

END WALL FRAMING ELEVATION @

GL-1 & GL-7

DOOR JAMB DETAIL 12

Abanzuela Text Box c

Attachment J.1.F