140R6024R0010_Amend__No__0002_0002.pdf

(x)

140R6024R0010 x x

1 copies of the amendment; (b) By acknowledging receipt of this amendment on each copy of the offer submitted ; or (c) By separate letter or electronic communication which includes a reference to the solicitation and amendment numbers. FAILURE OF YOUR ACKNOWLEDGEMENT TO BE

RECEIVED AT THE PLACE DESIGNATED FOR THE RECEIPT OF OFFERS PRIOR TO THE HOUR AND DATE SPECIFIED MAY RESULT IN REJECTION OF YOUR

OFFER. If by virtue of this amendment you desire to change an offer already submitted , such change may be made by letter or electronic communication, provided each letter or electronic communication makes reference to the solicitation and this amendment, and is received prior to the opening hour and date specified.

x

Billings MT 59107

R60

PO Box 36900 Regional Office Great Plains Region Bureau of Reclamation

02/21/20240002

13. THIS ITEM ONLY APPLIES TO MODIFICATION OF CONTRACTS/ORDERS. IT MODIFIES THE CONTRACT/ORDER NO. AS DESCRIBED IN ITEM 14.

12. ACCOUNTING AND APPROPRIATION DATA (If required) is not extended.is extended, Items 8 and 15, and returning

Offers must acknowledge receipt of this amendment prior to the hour and date specified in the solicitation or as amended , by one of the following methods: (a) By completing

The above numbered solicitation is amended as set forth in Item 14. The hour and date specified for receipt of Offers

11. THIS ITEM ONLY APPLIES TO AMENDMENTS OF SOLICITATIONS

FACILITY CODE CODE

10B. DATED (SEE ITEM 13)

10A. MODIFICATION OF CONTRACT/ORDER NO.

9B. DATED (SEE ITEM 11)

9A. AMENDMENT OF SOLICITATION NO.

CODE

8. NAME AND ADDRESS OF CONTRACTOR (No., street, county, State and ZIP Code)

7. ADMINISTERED BY (If other than Item 6)CODE 6. ISSUED BY

PAGE OF PAGES

4. REQUISITION/PURCHASE REQ. NO.3. EFFECTIVE DATE2. AMENDMENT/MODIFICATION NO. 5. PROJECT NO. (If applicable)

1. CONTRACT ID CODE

AMENDMENT OF SOLICITATION/MODIFICATION OF CONTRACT

01/11/2024

CHECK ONE A. THIS CHANGE ORDER IS ISSUED PURSUANT TO: (Specify authority) THE CHANGES SET FORTH IN ITEM 14 ARE MADE IN THE CONTRACT

B. THE ABOVE NUMBERED CONTRACT/ORDER IS MODIFIED TO REFLECT THE ADMINISTRATIVE CHANGES (such as changes in paying office, C. THIS SUPPLEMENTAL AGREEMENT IS ENTERED INTO PURSUANT TO AUTHORITY OF:

D. OTHER (Specify type of modification and authority) appropriation data, etc.) SET FORTH IN ITEM 14, PURSUANT TO THE AUTHORITY OF FAR 43.103(b).

E. IMPORTANT: Contractor is not is required to sign this document and return __________________ copies to the issuing office.

ORDER NO. IN ITEM 10A.

16A. NAME AND TITLE OF CONTRACTING OFFICER (Type or print)15A. NAME AND TITLE OF SIGNER (Type or print)

15C. DATE SIGNED 16B. UNITED STATES OF AMERICA 15B. CONTRACTOR/OFFEROR 16C. DATE SIGNED

(Signature of person authorized to sign) (Signature of Contracting Officer)

Ryan Cope

STANDARD FORM 30 (REV. 11/2016)

Prescribed by GSA FAR (48 CFR) 53.243

Previous edition unusable

14. DESCRIPTION OF AMENDMENT/MODIFICATION (Organized by UCF section headings, including solicitation/contract subject matter where feasible.)

Norton Dam Spillway Radial Gate Wire Rope Replacement Almena Unit, Kansas Division Pick-Sloan Missouri Basin Program, Kansas.

Please see attached for incorporated changes:

Except as provided herein, all terms and conditions of the document referenced in Item 9 A or 10A, as heretofore changed, remains unchanged and in full force and effect .

Amendment No. 0002 Solicitation No. 140R6024R0010

Description of Changes:

1. Standard Form 1442, Block 13, Line a: Extend the proposal submission date by 7 days to 1530 on 03/04/2024.

2. In Part I – Section C, Division 02, remove Section 02 83 30 in its entirety and replace it with Revised Section 02 83 30. The specific change is: Section 02 83 30, Paragraph 1.07A3 “Current certification by KDHE as a Lead Activity Firm” has been deleted from the specifications.

For convenience, essential changes on the revised solicitation page are indicated by a vertical line within the margin, whereby the lines or paragraphs are changed from the previous version.

However, all portions of the revised solicitation pages shall apply whether changes thereon have been indicated or not.

Acknowledgement: See Block 11 on the Standard Form 30 regarding acknowledgement by offerors to this amendment. The Government requires acknowledgment by offerors to this amendment at the place designated for receipt of proposals. (Please see Block 19 on the Standard Form 1442.)

Third Party: If you have provided a copy of this solicitation to another company or individual, please forward this amendment accordingly.

SOLICITATION, OFFER,

AND AWARD

2. TYPE OF SOLICITATION

6. PROJECT NO. 4. CONTRACT NO. 5. REQUISITION/PURCHASE REQUEST NO.

PAGE OF PAGES

7. ISSUED BY CODE 8. ADDRESS OFFER TO

SOLICITATION

(Construction, Alteration, or Repair)

1. SOLICITATION NO. 3. DATE ISSUED

IMPORTANT -- The "offer" section on the reverse must be fully completed by offeror.

9.

INFORMATION

a. NAME b. TELEPHONE NO. (Include area code) (NO COLLECT CALLS)

NOTE: In sealed bid solicitations "offer" and "offeror" mean "bid" and "bidder."

CALL:

FOR

SEALED BID (IFB)

NEGOTIATED (RFP)

Bureau of Reclamation

Great Plains Region

Regional Office PO Box 36900

R60

Billings MT 59107

Bureau of Reclamation / MB-5000

Attn: Howard Heflin 2021 4th Ave North Billings MT 59101

Howard Heflin 4062477797

1x 1/11/2024

140R6024R0010

10. THE GOVERNMENT REQUIRES PERFORMANCE OF THE WORK DESCRIBED IN THESE DOCUMENTS (Title, identifying no., date)

Norton Dam Spillway Radial Gate Wire Rope Replacement Almena Unit, Kansas Division Pick- Sloan Missouri Basin Program, Kansas.

The magnitude of this project is between $1,000,000 and $5,000,000.

The North American Industry Classification System (NAICS) code is: 237990 - Other Heavy and Civil Engineering Construction.

The Small Business Size Standard is: $45 Million.

The Product or Service Code (PSC) is: Z2KA - Repair or Alterations of Dams.

The solicitation is issued as a Total Small Business Set-Aside.

Proposals are to be submitted via email to hheflin@usbr.gov. Reclamation's email servers limit attachments to 25 MB per message. Therefore, the offeror may need to submit multiple emails to ensure the Contract Specialist receives the complete proposal (Volumes 1-3).

The Offeror shall fill out the following:

Taxpayer Identification Number (TIN): _______________ System for Award Management (SAM) Unique Entity Identification (UEI): ______________ Commercial and Government Entity Code (CAGE): ______________ Currently Registered in System for Award Management (SAM): Yes or No. Indicate date SAM registration will expire: _______________

Continued ...

11. The Contractor shall begin performance within

12a. THE CONTRACTOR MUST FURNISH ANY REQUIRED PERFORMANCE AND PAYMENT BONDS?

award, notice to proceed. The performance period is mandatory negotiable. (See ________________________________________________.)

13. ADDITIONAL SOLICITATION REQUIREMENTS:

is not required.is, b. An offer guarantee

c. All offers are subject to the (1) work requirements, and (2) other provisions and clauses incorporated in the solicitation in full text or by reference.

(date). If this is a sealed bid solicitation, offers will be publicly opened at that time. Sealed envelopes containing offers shall be marked to show the offeror's name and address, the solicitation number, and the date and time offers are due.

d. Offers providing less than

12b. CALENDAR DAYSYES NO

(If "YES", indicate within how many calendar days after award in Item 12b.)

10 425 calendar days and complete it within ________________ ________________ calendar days after receiving

Paragraph F.1

a. Sealed offers in original and

03/04/2024___

NSN 7540-01-155-3212

x x x x copies to perform the work required are due at the place specified in Item 8 by _____________ ___________________ (hour) local time calendar days for Government acceptance after the date offers are due will not be considered and will be rejected . _________________

STANDARD FORM 1442 (Rev. 8/2014)

Prescribed by GSA

FAR(48 CFR) 53.236-1(d)

40625092

Amendment No. 0002 hheflin Stamp

17. The offeror agrees to perform the work required at the prices specified below in strict accordance with the terms of this solicitation, if this offer is accepted by the Government in writing within ____________________ calendar days after the date offers are due. (Insert any number equal to or greater than the minimum requirement stated in item 13d. Failure to insert any number means the offeror accepts the minimum in item 13d.)

14. NAME AND ADDRESS OF OFFEROR (Include ZIP Code) 15. TELEPHONE NO. (Include area code)

16. REMITTANCE ADDRESS (Include only if different than item 14.)

CODE FACILITY CODE

AMOUNTS

18. The offeror agrees to furnish any required performance and payment bonds.

19. ACKNOWLEDGEMENT OF AMENDMENTS

OFFER (Must be fully completed by offeror)

(The offeror acknowledges receipt of amendments to the solicitation -- give number and date of each)

AMENDMENT NO.

DATE.

20a. NAME AND TITLE OF PERSON AUTHORIZED TO SIGN OFFER (Type or print) 20b. SIGNATURE 20c. OFFER DATE

AWARD (To be completed by Government)

21. ITEMS ACCEPTED:

22. AMOUNT 23. ACCOUNTING AND APPROPRIATION DATA

24. SUBMIT INVOICES TO ADDRESS SHOWN IN

(4 copies unless otherwise specified)

ITEM 25. OTHER THAN FULL AND OPEN COMPETITION PURSUANT TO

26. ADMINISTERED BY CODE 27. PAYMENT WILL BE MADE BY

CONTRACTING OFFICER WILL COMPLETE ITEM 28 OR 29 AS APPLICABLE

(Contractor is required to sign this document and return (Contractor is not required to sign this document.)

Your offer on this solicitation is hereby accepted as to the items listed. This award consummates the contract, which consists of (a) the Government solicitation and your offer, and (b) this contract award.

No further contractual document is necessary.

30a. NAME AND TITLE OF CONTRACTOR OR PERSON AUTHORIZED TO SIGN (Type or print) 31a. NAME OF CONTRACTING OFFICER (Type or print)

30b. SIGNATURE 30c. DATE 31b. UNITED STATES OF AMERICA 31c. DATE

BY

2PAGE OF

Bureau of Reclamation Great Plains Region

Regional Office PO Box 36900

R60

Billings MT 59107

Ryan Cope

28. NEGOTIATED AGREEMENT 29. AWARD

Contractor agrees to furnish and deliver all items or perform all work requirements identified on this form and any continuation sheets for the consideration stated in this contract. The rights and obligations of the parties to this contract shall be governed by (a) this contract award, (b) the solicitation, and (c) the clauses, representations, certifications, and specifications incorporated by reference in or attached to this contract.

copies to issuing office.)

10 U.S.C. 2304(c) 41 U.S.C. 3304(a)

STANDARD FORM 1442 (REV. 8/2014) BACK

Continued...

ITEM NO.

(A)

SUPPLIES/SERVICES

(B)

QUANTITY

(C)

UNIT

(D)

UNIT PRICE

(E)

AMOUNT

(F)

NAME OF OFFEROR OR CONTRACTOR

3 3

CONTINUATION SHEET

REFERENCE NO. OF DOCUMENT BEING CONTINUED PAGE OF

140R6024R0010

1 Norton Dam Spillway Radial Gate Wire Rope

Replacement

See attached Continuation of Section B (CLINs 1-5)

NSN 7540-01-152-8067 OPTIONAL FORM 336 (4-86)

Sponsored by GSA

FAR (48 CFR) 53.110

00010 AU $____________

Norton Dam Spillway Amendment No. 0002 Radial Gate Wire Rope Replacement Specifications No. 60-C0683

Removal and Disposal of Coatings Containing Regulated Metals

Revised 02 83 30 - 1

SECTION 02 83 30

REMOVAL AND DISPOSAL OF COATINGS CONTAINING REGULATED METALS

PART 1 GENERAL

1.01 MEASUREMENT AND PAYMENT

A. Removal and Disposal of Coatings Containing Regulated Metals:

1. Payment: Lump-sum price offered in the Price Schedule.

2. Include in price offered in the Price Schedule the following items requiring removal of coatings containing regulated metals (refer to Section 09 96 20 – Coatings, Section 51 02 83 – Existing Coatings Analysis, and Section 52 00 00 – Drawings for details):

a. Spot repairs on the exterior surfaces of each of the radial gate hoist assemblies located on the hoist deck, as well as the floatwell cover frames, weirwell cover frames, and pier platform frames.

b. Full recoat of the wire rope clamps and sockets, sheave assemblies, floatwell and weirwell covers, and platforms for each of the radial gates.

3. Include the prices for On-site Certified Industrial Hygienist (CIH) oversight and laboratory costs.

4. On-site CIH oversight costs for coatings application shall be included in Section 09 96 20 – Coatings.

5. Include the cost of characterizing, handling, and disposing of nonhazardous waste. For cost estimating purposes, the Contractor may assume that some waste streams may be rendered nonhazardous (e.g. by dilution with abrasive media) during the removal process. Refer to Articles 1.11 and 3.05 of this Section for further details.

1.02 DEFINITIONS AND ABBREVIATIONS

A. ABIH: American Board of Industrial Hygiene.

B. ACGIH: American Conference of Governmental Industrial Hygienists.

C. AIHA: American Industrial Hygiene Association.

D. Background Monitoring and Sampling:

1. Sampling conducted in and around regulated areas prior to commencing on-site work, and outside of regulated areas during on-site work.

2. Used as a baseline for other sampling.

E. CIH: Certified Industrial Hygienist.

Revised 02 83 30 - 2

F. Clearance Sampling:

1. Sampling conducted in and around regulated areas prior to relocation or removal of the containment system, or after a potentially uncontrolled release.

2. Compared with background samples or other baselines to confirm clearance for continued work.

G. Coatings containing regulated metals:

1. Coatings which could generate the release of airborne contaminants during removal, in concentrations which exceed the OSHA PEL or the ACGIH TLV for regulated metals.

2. Coatings which, upon removal, generate solid waste that could be found toxic when tested in accordance with EPA Test Method 1311.

H. Competent Person:

1. As defined in 29 CFR 1926.32(f).

2. Capable of identifying existing and predictable hazards in connection with the removal and disposal of coatings containing regulated metals.

3. Has authorization to take prompt corrective measures to eliminate hazards.

4. Experienced in administration and supervision under OSHA and EPA regulations.

5. Familiar with the applicable standards and regulations listed in Article 1.06 of this

Section.

I. EPA: Environmental Protection Agency.

J. Hazardous waste: As defined in 40 CFR 261.3.

K. HEPA: High Efficiency Particulate Absolute filtration efficiency of 99.97% at 0.3 microns.

L. Hazardous waste: As defined in 40 CFR 261.3.

M. KDHE: Kansas Department of Health and Environment.

N. MAP: Model Accreditation Plan.

O. NESHAP: National Emissions Standards for Hazardous Air Pollutants, as defined in

40 CFR 61.

P. NIOSH: National Institute for Occupational Safety and Health.

Q. NIST: National Institute of Standards and Technology.

R. NVLAP: National Voluntary Laboratory Accreditation Program.

Revised 02 83 30 - 3

S. OSHA: Occupational Safety and Health Administration.

T. PEL: Permissible Exposure Limit, as defined in 29 CFR 1910.1000 Table Z 1.

U. PPE: Personal protective equipment.

V. Post-Construction Sampling:

1. Sampling conducted in and around regulated areas after completion of on-site work.

2. Compared with preconstruction samples or other baselines to confirm successful removal of materials containing regulated metals without contamination of the surrounding environment.

W. Preconstruction Sampling:

1. Sampling conducted in and around regulated areas prior to commencing on-site work.

2. Used to verify presence and concentration of regulated metals and to provide a baseline for subsequent sampling.

X. RCRA: Resource Conservation and Recovery Act.

Y. Regulated area:

1. Areas where hazardous material removal operations are performed, which are isolated by physical boundaries which assist in the prevention of the uncontrolled release of regulated metals.

2. Refer to the regulations and standards listed in Article 1.06 of this Section.

Z. Regulated (RCRA 8) metals:

1. Arsenic: See 29 CFR 1910.1018..

2. Barium.

3. Cadmium: See 29 CFR 1926.1127.

4. Chromium: See 29 CFR 1926.1126.

5. Lead: See 29 CFR 1926.62.

6. Mercury (below reportable amount).

7. Selenium (not detected).

8. Silver.

AA. Removal Activities and Handling: Include (but are not limited to) grinding, sanding, abrasive blasting, solvent cleaning, chemical stripping, hand or power tool removal, scraping, peeling, cutting, isolation, containment, collection, packaging, storage, transportation, and disposal of existing coatings.

Revised 02 83 30 - 4

BB. Reportable Quantities: as defined in 40 CFR 117 and 40 CFR 302.

CC. SSPC: Society for Protective Coatings.

DD. TCLP: Toxicity Characteristic Leaching Procedure, per EPA Test Method 1311.

EE. TLV: Threshold Limit Value, as defined by ACGIH.

FF. TSD facility: Hazardous Waste Treatment, Storage, and Disposal facility.

GG. Technically Qualified Person: as referenced in 29 CFR 1926.55(b).

1. Familiar with the construction and operation of any and all equipment and technical measures required for removal of materials containing regulated metals.

2. Familiar with the hazards involved, as well as all applicable standards and regulations listed in Article 1.06 of this Section.

HH. Working Level Monitoring:

1. Sampling conducted in and around regulated areas during on-site work.

2. Used to confirm compliance with emissions and employee exposure standards and regulations.

1.03 REFERENCE STANDARDS

A. American Conference of Governmental Industrial Hygienists (ACGIH)

1. ACGIH TLVs Threshold Limit Values, found at www.acgih.org

B. Bureau of Reclamation (USBR)

1. RSHS Reclamation Safety and Health Standards, including revisions posted at https://www.usbr.gov/safety/rshs/index.html

C. Code of Federal Regulations (CFR)

1. 29 CFR 1910 Occupational Safety and Health Standards

a. .134 Respiratory Protection

b. .1000 Air Contaminants [PELs]

c. .1018 Inorganic Arsenic

d. .1200 Hazard Communication

2. 29 CFR 1926 Safety and Health Regulations for Construction

a. .32 Definitions

b. .55 Gases, Vapors, Fumes, Dusts, and Mists

c. .62 Lead http://www.acgih.org/ https://www.usbr.gov/safety/rshs/index.html

Revised 02 83 30 - 5

d. Subpart M Fall Protection

e. .1126 Chromium (VI)

f. .1127 Cadmium

3. 40 CFR Chapter I Environmental Protection Agency

a. .61 Subpart A National Emission Standards for Hazardous

Air Pollutants [NESHAP] – General Provisions

b. .117 Determination of Reportable Quantities for Hazardous Substances [under the Clean Water Act]

c. .260 Hazardous Waste Management System:

General

d. .261 Identification and Listing of Hazardous Waste

e. .262 Standards Applicable to Generators of Hazardous Waste

1) .262.12 EPA Identification Numbers

2) Subpart B Manifest Requirements Applicable to Small and Large Quantity Generators [of Hazardous Waste]

f. .263 Standards Applicable to Transporters of Hazardous Waste

g. .264 Standards for Owners and Operators of Hazardous Waste Treatment, Storage, and Disposal Facilities

h. .268 Land Disposal Restrictions

i. .300 National Oil and Hazardous Substances

Pollution Contingency Plan [NCP]

j. .302 Designation, Reportable Quantities, and

Notification [under the NCP]

4. 49 CFR Chapter I Pipeline and Hazardous Materials Safety

Administration, Department of Transportation

a. .107 Hazardous Materials Program Procedures

b. .171 General Information, Regulations, and

Definitions

c. .172 Hazardous Materials Table, Special

Provisions, Hazardous Materials Communications, Emergency Response

Revised 02 83 30 - 6

Information, Training Requirements, and Security Plans

d. .173 Shippers – General Requirements for Shipments and Packagings

e. .177 Carriage by Public Highway

f. .178 Specifications for Packagings

D. Environmental Protection Agency (EPA)

1. EPA Test Method 1311 Toxicity Characteristic Leaching Procedure [TCLP]

E. Kansas Administrative Regulations (KAR)

1. Available at https://www.kssos.org/pubs/pubs_kar.aspx

2. KAR 28-19-735 National Emission Standards for Hazardous Air

Pollutants [40 CFR 61]

3. KAR 28-29-6 Solid Waste Management, Permits and Engineering

Plans

4. KAR 28-31 Hazardous Waste Management Standards and

Regulations

a. 28-31-4 EPA Identification Numbers; Notification

Requirement for Hazardous Waste, Universal Waste, and Used Oil Activities

b. 28-31-260 and 260a General Provisions and Definitions;

Adoption and Modification of Federal Regulations [40 CFR 260] and Additional State Definitions

c. 28-31-261 and 261a Identification and Listing of Hazardous Waste; Adoption and Modification of Federal Regulations [40 CFR 261] and Additional State Definitions

d. 28-31-262 and 262a Generators of Hazardous Waste; Adoption and Modification of Federal Regulations [40 CFR 262] and Additional State Definitions

e. 28-31-263 and 263a Transporters of Hazardous Waste; Adoption and Modification of Federal Regulations [40 CFR 263] and Additional State Definitions

f. 28-31-264 and 264a Hazardous Waste Treatment, Storage, and Disposal Facilities; Adoption and Modification of Federal Regulations https://www.kssos.org/pubs/pubs_kar.aspx

Revised 02 83 30 - 7

[40 CFR 264] and Additional State Definitions

g. 28-31-268 Land Disposal Restrictions; Adoption and Modification of Federal Regulations

[40 CFR 268]

5. KAR 28-48 Spill Reporting

F. KDHE Bureau of Waste Management – Technical Guidance Documents (HW)

1. Available at http://www.kdheks.gov/waste/p_techguides.html

2. HW 1995 G2 Solvent-Contaminated Wipes

3. HW 2005 G1 Container Management for Hazardous Waste

Generators

4. HW 2010 G1 Wastes Containing Lead-Based Paint

5. HW 2011 G1 Hazardous Waste Determinations and

Documentation

6. HW 2011 G2 Characteristic and Listed Hazardous Wastes

7. HW 2015 G1 Solid and Hazardous Waste Recordkeeping

Requirements

G. Society For Protective Coatings (SSPC)

1. SSPC C3 Lead Paint Removal Training

2. SSPC C5 Lead Paint Removal Refresher Training

3. SSPC Guide 6-2015 Containing Surface Preparation Debris Generated

During Paint Removal Operations

4. SSPC QP2-2009 Procedure for Evaluating the Qualifications of

Painting Contractors (Field Removal of Hazardous Coatings from Complex Structures)

1.04 SUBMITTALS

A. Submit the following in accordance with Section 01 33 00 – Submittals.

B. RSN 02 83 30-1, Resumes and Qualifications:

1. Provide resumes and qualifications for the following personnel and entities (refer to Article 1.07 of this Section for details):

a. Coatings Removal Contractor

b. Coatings Removal Project Designer

c. Coatings Removal Supervisor

d. Coatings Removal Workers http://www.kdheks.gov/waste/p_techguides.html

Revised 02 83 30 - 8

e. Independent Testing Laboratory

f. Hazardous Waste Transporter

g. TSD Facility

C. RSN 02 83 30-2, Coatings Removal Plans.

1. Include the following elements (refer to Article 1.09 of this Section for details):

a. Containment System Plan

b. Ventilation Plan

c. Worker Protection Compliance Program

d. Emissions Monitoring Plan

e. Waste Characterization, Handling, and Disposal Plan

f. Contamination Contingency Plan

D. RSN 02 83 30-3, Preconstruction Test Results:

1. Include the following preconstruction test results (refer to Articles 1.10 and 3.04 of this Section for details):

a. Preconstruction wipe sample analyses.

b. Background area air sample analyses.

c. Background water sample analysis.

E. RSN 02 83 30-4, Working Level Test Results:

1. Include the following working level test results (refer to Articles 1.10, 3.02, and

3.04 of this Section for details):

a. Personal air monitor sample analyses.

b. Area air sample analyses.

c. Water sample analysis.

d. Pressure differential recordings for containment areas.

2. Test results shall be submitted within seven (7) days after receipt from the independent testing laboratory.

F. RSN 02 83 30-5, Clearance and Post-Construction Test Results:

1. Include the following clearance and post-construction test results (refer to Articles

1.10 and 3.04 of this Section for details):

a. Area air sample analyses.

b. Wipe sample analyses.

c. Water sample analysis.

2. Compare with background test results.

Revised 02 83 30 - 9

3. Demonstrate compliance with specified acceptance criteria.

G. RSN 02 83 30-6, Waste Characterization and Disposal Records:

1. For each type of waste generated under this Section, provide the following, as applicable (refer to Articles 1.10 and 3.05 of this Section for details):

a. Waste characterization results

b. Actual quantities generated, and disposal locations

c. Nonhazardous wastes: Bills of Lading from transporter and disposal facility.

d. Hazardous wastes: Manifests, Certificates of Disposal, and if applicable, Exception Reports.

1.05 PROJECT CONDITIONS

A. Existing coatings contain regulated metals. Refer to Section 51 02 83 – Existing Coatings Analysis and Section 52 00 00 – Drawings for details.

B. Work will be conducted in areas where drainage enters a waterway. Release of contaminants into this waterway is prohibited.

C. The remote location of the work site requires additional planning for outside emergency assistance and timely laboratory support.

D. Work activities will require controlling the temperature and humidity inside the containments to account for changing weather conditions. Refer to Section 09 96 20 – Coatings.

E. The Contractor will be considered the co-generator of any hazardous waste, in accordance with KAR 28-31-262 and 40 CFR 260.10. The Contractor will need to obtain an EPA Identification Number per KAR 28-31-4 and 40 CFR 262.18.

1.06 STANDARDS AND REGULATORY REQUIREMENTS

A. Safety and Health:

1. General: RSHS; 29 CFR 1910.1000, 1926.32, and 1926.55; 40 CFR 61; and

ACGIH TLVs.

2. Regulated metals: 29 CFR 1926.62, 1926.1126, and 1926.1127.

3. Respiratory Protection: 29 CFR 1910.134; and 1926.62(f).

4. Hazard Communication: 29 CFR 1910.1200.

5. Exposure Limits: 29 CFR 1910.1000 (OSHA PELs) and ACGIH TLVs.

6. Fall Protection: 29 CFR Subpart M.

B. Handling of Regulated Metals:

Revised 02 83 30 - 10

1. General: KAR 28-19-735 and 40 CFR 61.

2. Containment and Ventilation: SSPC Guide 6; and KAR 28-50-9.

3. Reportable Releases: KAR 28-48; and 40 CFR 117, 300, and 302.

C. Hazardous Waste:

1. General: KAR 28-29-6, 28-31-4, 28-31-260 and 260a, 28-31-261 and 261a, and

28-31-262 and 262a; HW 1995 G2, HW 2010 G1, HW 2011 G1, HW 2011 G2, and HW 2015 G1; 40 CFR 260, 261, and 262; and 49 CFR 107, 171, and 172.

2. Containment: HW 2005 G1 and 49 CFR 178.

3. Transportation: KAR 28-31-263 and 263a; 40 CFR 263; and 49 CFR 173 and

177.

4. Disposal: KAR 28-31-264 and 264a, 28-31-268, and 28-50-14; and 40 CFR 264 and 268.

D. All other applicable Federal, State, and local regulations not listed above shall apply.

E. In case of conflict, the most stringent regulations and standards shall apply.

1.07 QUALIFICATIONS

A. Coatings Removal Contractor:

1. Current EPA Identification Number.

2. Current certification by the SSPC Painting Contractor Certification Program.

3. Deleted

B. Coatings Removal Project Designer:

1. Signed documentation demonstrating credential as a Technically Qualified

Person, as defined in Article 1.02 of this Section.

2. Current EPA or KDHE Lead Abatement Project Designer certification.

3. Documentation of credentials and experience (5 years minimum) in containment structure and ventilation system design.

C. Coatings Removal Supervisor:

1. Signed documentation demonstrating credential as a Competent Person, as defined in Article 1.02 of this Section.

2. Certifications of SSPC C3 training and refresher training (SSPC C5) within the last 12 months.

3. Current EPA or KDHE Lead Abatement Supervisor certification.

D. Coatings Removal Workers:

1. Current EPA or KDHE Lead Abatement Worker certification.

Revised 02 83 30 - 11

E. On-site CIH:

1. Refer to Section 01 35 30 – Contractor’s On-site Safety and Health Personnel.

F. Independent Testing Laboratory:

1. Current certifications and accreditations under the EPA National Lead Laboratory

Accreditation Program, AIHA, NIST, NVLAP, and/or KDHE for performing tests according to approved standards and methods.

G. Hazardous Waste Transporter:

1. Current EPA Identification Number.

2. Current license for hazardous material transport.

3. Documentation of compliance with 49 CFR Chapter I.

H. Solid waste disposal facility:

1. Current license for solid waste disposal.

I. TSD facility:

1. Current RCRA Subtitle C permit.

2. Current license for hazardous waste disposal.

3. Current EPA Identification Number.

1.08 AUTHORITIES, DUTIES, AND RESPONSIBILITIES

A. Coatings Removal Project Designer:

1. Prepare and sign the Coatings Removal Plans.

B. Coatings Removal Supervisor:

1. Review and sign the Coatings Removal Plans.

2. On jobsite during all coating removal activities. Available for emergencies.

3. Control entry to and from any regulated area.

4. Ensure that employees wear appropriate PPE, are trained in the use of appropriate methods for exposure control, use proper hygiene methods and decontamination procedures.

5. Ensure that engineering controls in use are in proper operating condition and are functioning properly.

6. Responsible for compliance with applicable Federal, State of Kansas, and local requirements; and the approved Coatings Removal Plans.

7. Take prompt corrective measures to eliminate hazards from regulated metals.

C. On-site CIH:

Revised 02 83 30 - 12

1. Refer to Section 01 35 30 – Contractor’s On-Site Safety and Health Personnel.

2. Review and sign the Coatings Removal Plans.

3. Review, analyze, and sign the Preconstruction, Working Level, Clearance, Post-

Construction, and Waste Characterization Test Results.

4. Ensure that employee exposure monitoring is conducted in accordance with the applicable standards and regulations listed in Article 1.06 of this Section.

5. Conduct emissions sampling.

6. Conduct clearance testing.

7. Conduct containment and ventilation system testing.

8. Characterize solid waste debris generated from removal operations.

1.09 COATINGS REMOVAL PLANS

A. Submit plans, for approval, which detail the engineering controls, administrative controls, and procedures to be implemented during coating removal operations. The plans shall be:

1. Prepared and signed by the Coatings Removal Project Designer.

2. Reviewed and signed by the On-site CIH and Coatings Removal Supervisor.

B. Containment System Plan:

1. Detailed plan to prevent the release of coatings, metals, and dusts into the environment during the disturbance, removal, and reapplication of coatings in accordance with Article 3.02 and the applicable regulations and standards listed in Article 1.06 of this Section.

2. Include (but do not limit to) the following information:

a. Coatings removal methods to be conducted within each containment (refer to Section 09 96 20 – Coatings).

b. Detailed project drawings and descriptions of the proposed containment structure, device, or method of containment, showing the SSPC Containment System Class (see Table 02 83 30A – Containment Criteria for Removal of Paint Containing Regulated Metals, below), general layout, attachment to the structure, and relationship to the structure.

c. Details and locations of decontamination units, temporary storage facilities, and boundaries of each regulated area.

d. Load analysis for the containment system on the structure, including wind loads and dead load from debris.

e. Performance criteria for the containment. Emission of dusts, metals, toxic vapors, or gases into the surrounding environment is prohibited.

f. Inspection criteria for the containment system.

Revised 02 83 30 - 13

g. Specifications on sheet plastic, prefabricated decontamination units, and other materials or equipment specific to containment. Include (but do not limit to) manufacturer/supplier contact information, model, capacity, performance characteristics, safety data sheets, etc.

C. Ventilation Plan:

1. Detailed plan to ventilate, maintain negative pressure, and monitor pressure within the containment system; and to filter exhaust from the containment system during the disturbance, removal and reapplication of coatings in accordance with Article 3.02 and the applicable regulations and standards listed in Article 1.06 of this Section.

2. Include (but do not limit to) the following information:

a. Detailed project drawings and descriptions of the proposed ventilation equipment that will be used (see Table 02 83 30A – Containment Criteria for Removal of Paint Containing Regulated Metals, below), as well as any temporary utilities. Include performance criteria and specifications for equipment.

b. Plan for maintaining negative pressure and monitoring pressure.

c. Detailed description and calibration data for instrumentation that will be used to test ventilation system performance.

d. Testing procedures.

a. Specifications for the filtration system. Emission of dusts or vapors into the facility is prohibited. Dust collection system shall filter exhaust air to HEPA efficiency.

b. Detailed system performance calculations for air flow, air changes in the containment, velocity, and static pressures in ducting, and fan performance.

c. Specifications on ventilation units, HEPA filters, and other applicable materials or equipment. Include (but do not limit to) manufacturer/supplier contact information, model, capacity, performance characteristics, safety data sheets, etc.

Revised 02 83 30 - 14

Ta bl e

A

C on ta in m en t C rit er ia fo r R em ov al o f P ai nt

C on ta in in g

R eg ul at ed M et al s1

Ex ha us t

Fi ltr at io n R eq ui re d

N o

N o

N o

N o

Y es

N o

N ot es

1.

T hi s t ab le p ro vi de s g en er al d es ig n cr ite ria o nl y.

I t d oe s n ot g ua ra nt ee th at sp ec ifi c co nt ro ls o ve r e m is si on s w ill o cc ur b ec au se u ni qu e si te c on di tio ns m us t b e co ns id er ed in th e de si gn

O th er c om bi na tio ns o f m at er ia ls m ay p ro vi de c on tro ls ov er e m is si on s e qu iv al en t t o or g re at er th an th os e co m bi na tio ns sh ow n ab ov e.

2.

T he

S

SP

C C la ss ifi ca tio n is b as ed o n

SS

PC

G ui de

N ot e th at fo r w or k ov er w at er , w at er b oo m s o r b oa ts w ith sk im m er s m us t b e em pl oy ed , w he re fe as ib le

, t o co nt ai n sp ill s o r re le as es

D eb ris m us t b e re m ov ed d ai ly a t a m in im um

3.

P er m ea bi lit y ad dr es se s b ot h ai r a nd w at er a s a pp ro pr ia te

In th e ca se o f w at er re m ov al m et ho ds

, t he c on ta in m en t m at er ia ls m us t b e re si st an t t o w at er

G ro un d co ve rs sh ou ld al w ay s i m pe rm ea bl e, a nd o f s uf fic ie nt st re ng th to w ith st an d th e im pa ct a nd w ei gh t o f t he d eb ris a nd th e eq ui pm en t u se d fo r c ol le ct io n an d cl ea n-up

G ro un d co ve rs m us t a ls o ex te nd b ey on d th e co nt ai nm en t b ou nd ar y to c ap tu re e sc ap in g de br is

4.

If d eb ris e sc ap es th ro ug h th e se am s, th en a dd iti on al se al in g of th e se am s a nd jo in ts is re qu ire d.

5.

W he n

N at ur al is li ste d, v en til at io n is n ot re qu ire d pr ov id ed th e em is si on s a re c on tro lle d as sp ec ifi ed in th is S pe ci al P ro vi si on

, a nd p ro vi de d w or ke r e xp os ur es a re p ro pe rly co nt ro lle d.

I f u na cc ep ta bl e em is si on s o r w or ke r e xp os ur es to le ad o r o th er to xi c m et al s o cc ur

, i nc or po ra te a v en til at io n sy st em in to th e co nt ai nm en t.

6.

G ro un d co ve rs a nd w al l t ar pa ul in s m ay p ro vi de su ita bl e co nt ro ls ov er e m is si on s w ith ou t t he n ee d to c om pl et el y en cl os e th e w or k ar ea

7.

T hi s m et ho d ap pl ie s t o w at er c le an in g to re m ov e su rf ac e co nt am in an ts

, a nd w at er je tti ng

(w ith a nd w ith ou t a br as iv e) a nd w et a br as iv e bl as t c le an in g w he re th e go al is to re m ov e pa in t.

A lth ou gh b ot h pe rm ea bl e an d im pe rm ea bl e co nt ai nm en t m at er ia ls a re in cl ud ed , g ro un d co ve rs a nd th e lo w er p or tio ns o f t he c on ta in m en t m us t b e w at er im rm ea bl e w ith fu lly se al ed jo in ts

, a nd o f s uf fic ie nt st re ng th a nd in te gr ity to fa ci lit at e th e co lle ct io n an d ho ld in g of th e w at er a nd d eb ris fo r p ro pe r d is po sa l.

If w at er o r de br is

, o th er th an m is t, es ca pe th ro ug h up pe r s id ew al ls o r c ei lin g ar ea s c on st ru ct ed o f p er m ea bl e m at er ia ls , t he y sh al l b e re pl ac ed w ith im pe rm ea bl e m at er ia ls

Pe rm ea bl e m at er ia ls fo r t he p ur po se o f t hi s s pe ci fic at io n ar e de fin ed a s m at er ia ls w ith o pe ni ng s m ea su rin g m ils

(1 m ic ro

n) o r l es s i n gr ea te st d im en si on eg at iv e Pr es su re

R eq ui re d

N o

N o

N o

N o

Y o

V en til at io n

Sy st em eq ui re d5

N at ur

M ec ha ni ca l

N at

C on ta in m en t

En try ay

O ve rla pp in g or n Se am rla pp in n rla pp in n rla pp in n

A irl oc k ea la bl e

O pe n

Su pp or t

St ru ct ur e

M in in ig id o r Fl ex ib le id , F le xi bl e, in id o r Fl ex er ia l

Jo in ts

Pa rti ly ed

Pa rti

Fu lly o r

Pa rti a nd

Pa rti

S ea le d

Pa rti

Pe rm ea bi lit y3

Pe rm ea bl e

Im rm ea bl e

Pe rm ea bl rm ea bl e

Pe rm ea bl rm ea bl e

Pe rm ea bl e an d Im pe rm ea bl e7

Im pe rm ea bl e

Pe rm ea bl e

Fl ex ib ili ty id o r Fl ex id o r Fl ex id o r Fl ex id o r Fl ex id o r Fl ex id o r Fl ex

SS

PC

C la ss

3P

3P

2P

2W -3

1A

4A

R em ov al

M et ho d

H an d To ol C le an in g

Po w er T oo l C le an in g w

V ac uu

Po er T oo l C le an in g

/o

V ac uu er Je tti ng et A br as iv e

B la st in g W at er

C le an in g7

A br as iv e B la st

C le an in g

V ac uu m

B la st C le an

Revised 02 83 30 - 15

D. Worker Protection Compliance Program:

1. Detailed plan to protect workers from and monitor worker exposure to regulated metals in accordance with the approved Safety Plan (refer to Section 01 35 20 – Safety and Health), Articles 3.03 and 3.04 of this Section, and the applicable regulations and standards listed in Article 1.06.

2. Include (but do not limit to) the following information:

a. Procedures, equipment, and training of workers on hazards involved with handling and disposing of regulated metals.

b. Plan for monitoring worker exposure to airborne contaminants using personal and area air monitors.

c. Plans for decontamination procedures, equipment, and facilities to be used during coating removal activities.

d. Specifications on respirators, personal air monitors, PPE, protective clothing, and other applicable materials or equipment, including (but not limited to) manufacturer/supplier contact information, model, capacity, performance characteristics, safety data sheets, etc.

3. Include (but do not limit to) the following sampling details:

a. Sampling and analysis methods.

b. Equipment calibration information.

c. Name of person conducting sampling.

d. Type and location of sampling (personal or area).

e. Collection media specifications.

f. Flow rates and duration of samples.

g. Name, contact person, address, and telephone number of proposed testing laboratory.

4. In lieu of including medical surveillance program details, provide certification, signed by a licensed physician, that the workers are being tested as part of a medical surveillance program in accordance with 29 CFR 1926.62(j).

a. Blood level testing shall include lead and zinc protoporphyrin (ZPP) tests, as well as monitoring for the other regulated metals present in the existing coatings.

b. Do not include personally identifiable information (PII) or medical information protected under the Health Insurance Portability and Accountability Act (HIPAA).

E. Emissions Monitoring Plan:

1. Detailed plan to monitor emissions of regulated metals in accordance with Article

3.04 of this Section, and the applicable regulations and standards listed in Article 1.06.

Revised 02 83 30 - 16

2. Include (but do not limit to) the following information:

a. Plans for conducting preconstruction, working level, clearance, and post-construction sampling, monitoring, and testing.

b. Specifications on area air monitors, wipes, water sampling equipment, wetting agents, encasement materials, disposal containers, and other applicable materials or equipment. Include (but do not limit to) manufacturer/supplier contact information, model, capacity, performance characteristics, safety data sheets, etc.

3. Include (but do not limit to) the following sampling details:

a. Analytical contaminant list sampling and analysis methods.

b. Equipment calibration information.

c. Name of person conducting sampling.

d. Type and location of sampling (personal or area).

e. Collection media specifications.

f. Flow rates and duration of samples.

g. Name, contact person, address, and telephone number of proposed testing laboratory.

F. Waste Characterization, Handling, and Disposal Plan:

1. Detailed plan to properly characterize, handle, and dispose of all waste generated from coatings removal operations in accordance with Article 3.05 of this Section and the applicable regulations and standards listed in Article 1.06.

2. Include (but do not limit to) the following information:

a. Estimated quantity and planned disposal location for each type of waste to be generated.

b. Plan for the sampling, testing, and characterization of waste:

1) Include sample collection and analytical test methods that will be used to characterize the waste.

2) Include the required method detection limits.

3) Describe the analytical data delivery package including quality control and quality assurance.

c. Plan for the handling, storage, transportation, and disposal of waste from coating removal operations, and the cleaning of reusable items.

d. Plan for the disposal of wastewater (see Section 01 57 00 – Water

Pollution Control).

e. Name, contact person, address and telephone number of proposed independent testing laboratory, transporter, disposal facility, and wastewater treatment facility.

Revised 02 83 30 - 17

f. Written notice from owner or operator of disposal facility documenting permits and agreement to accept hazardous waste generated under this contract.

g. Specifications on storage and disposal containers and other applicable materials or equipment. Include (but do not limit to) manufacturer/ supplier contact information, model, capacity, performance characteristics, safety data sheets, etc.

G. Contamination Contingency Plan:

1. Detailed contingency plan to handle a confirmed contamination over reportable quantities due to a breach in containment or storage, in accordance with Article

3.06 and the applicable regulations and standards listed in Article 1.06 of this Section.

2. Include (but do not limit to) the following information:

a. Plan for monitoring and reporting reportable releases. Include personnel to contact, telephone numbers, email addresses, time frames for contacting, and methods of contact.

b. Plan for decontamination of contaminated areas and surfaces.

1.10 LABORATORY TEST RESULTS

A. Submit exposure, emissions, and waste characterization test results for all monitoring and sampling conducted during coating removal operations. All test result submittals shall be:

1. Provided by an approved independent testing laboratory.

2. Reviewed, signed, and prepared for submittal by the On-site CIH.

3. Reviewed and signed by the Coatings Removal Supervisor.

B. Except for waste characterization samples, include a map indicating the location of each sample.

C. Provide appropriate quality control information to supplement analytical data. Include from blanks, laboratory control samples with percent recovery, duplicates, matrix spike samples with percent recovery, and other appropriate quality control measures.

D. Refer to Articles 3.04 and 3.05 of this Section for more details.

1.11 DISPOSING HAZARDOUS WASTE

A. The following applies if a waste stream containing regulated metals tests as hazardous waste (these provisions would be a modification to this specification):

1. Assemble a written plan to submit to the Reclamation CO for additional funds upon acceptance.

Revised 02 83 30 - 18

2. Obtain EPA Identification number (if not already obtained) before treating, storing, or transporting hazardous waste.

3. Handle and dispose of hazardous waste in accordance with Article 3.05 and the applicable regulations and standards in Article 1.06 of this Section.

PART 2 PRODUCTS

Not used.

PART 3 EXECUTION

3.01 COATINGS REMOVAL

A. Refer to Section 09 96 20 – Coatings for removal methods to be used.

B. Handle and dispose of coatings containing regulated metals in accordance with applicable Federal, State, and local regulations as well as the approved Coatings Removal Debris Abatement Plans.

3.02 CONTAINMENT AND VENTILATION

A. The containment and ventilation systems shall control emissions to the environment in conformance with applicable Federal, State, and local regulations and the following criteria:

1. Comply with the approved Containment System and Ventilation Plans during coating removal and coating application.

2. Do not exceed ambient air quality standards.

3. Prevent contamination of any reservoir, watercourse, or water system.

4. Prevent any contamination of sediment in any reservoir or watercourse.

5. Prevent any contamination of soil.

6. Suitable for surface preparation methods specified in Section 09 96 20 – Coatings.

7. Containment and ventilation components in accordance with SSPC Guide 6, as summarized in Table 02 83 30A – Containment Criteria for Removal of Paint Containing Regulated Metals, as well as the other standards and regulations listed in Article 1.06 of this Section.

8. Ventilate within the containment and filter exhaust air to HEPA efficiency.

9. Maintain and monitor negative pressure within the containment.

a. Record and submit pressure differential measurements in conjunction with personal air monitor sampling (refer to Article 3.02 of this Section).

b. Additional recordings may be taken at the discretion of the On-site CIH.

Revised 02 83 30 - 19

c. If pressure differential results fall below the minimum allowable pressure difference, stop work until appropriate corrective measures are taken, and perform additional monitoring as necessary until the required standards are met.

B. Perform the following activities within the containment system:

1. Coating removal.

2. Surface preparation.

3. Waste and debris containerization.

4. Activities which may spread contamination outside the Regulated Area.

5. Application, touch-up, and repair of new coatings (see Section 09 96 20 –

Coatings).

C. Provide signs and barriers at each point of entry to containment area to prevent unauthorized personnel access.

3.03 WORKER PROTECTION

A. Limit employee exposure to airborne contaminants in accordance with the applicable standards and regulations listed in Article 1.06 of this Section, and the approved Worker Protection Compliance Program.

3.04 EMISSIONS AND EXPOSURE MONITORING

A. General:

1. Sampling protocol shall be in accordance with the applicable standards listed in

Article 1.06 of this Section, as well as the approved Worker Protection Compliance Program and Emissions and Exposure Monitoring Plan.

2. All samples shall be analyzed by an approved independent testing laboratory.

Test results shall be reviewed for compliance by the On-site CIH and submitted.

3. Sampling and testing techniques shall conform to industry-standards and regulations, and shall be approved by Reclamation prior to the commencement of on-site work.

B. Preconstruction, Clearance, and Post-Construction Sampling:

1. Collect surface and high-volume air samples in and around all regulated areas and analyze samples for regulated metals.

2. Collect water samples in a transect across the spillway stilling basin, and analyze samples for regulated metals.

3. Clearance and post-construction levels shall meet the following requirements:

a. High-Volume Air Samples: At or below preconstruction levels.

Revised 02 83 30 - 20

b. Surface Samples: At or below 200 μg/ft2 (measured as an average concentration of all metals present in preconstruction samples, in micrograms per square foot of surface area sampled)

c. Water Samples: At or below preconstruction levels.

C. Working Level Monitoring:

1. Initial Exposure Assessment: At the commencement of coatings removal operations, the On-site CIH shall conduct and submit an initial exposure assessment for regulated metals in accordance with 29 CFR 1926.62(d).

2. Periodic Monitoring: Whether or not a Negative Exposure Assessment (NEA) has been made by the On-site CIH, the Contractor shall conduct periodic monitoring for regulated metals in accordance with 29 CFR 1926.62(d).

3. Collect and submit emissions samples in conjunction with personal air monitor sampling.

4. Do not exceed the emissions or exposure limits referenced in Article 1.06 of this Section.

5. If sample results exceed the specified emission or exposure limits, stop work until appropriate corrective measures are taken, and perform additional monitoring as necessary until the required standards are met.

6. Perform additional monitoring if there has been a change of equipment, process, control, or personnel, or a new task has been initiated that may result in emissions or exposures above the specified limits.

3.05 WASTE CHARACTERIZATION, HANDLING, AND DISPOSAL

A. Characterize, handle, transport, and dispose of solid waste debris generated from removal operations in accordance with the regulations and standards listed in Article 1.06 of this Section; the approved Waste Characterization, Handling, and Disposal Plan; and Section 01 74 00 – Cleaning and Waste Management.

1. Presume waste is hazardous until characterized.

a. The assumption that a particular waste stream will be nonhazardous for cost estimating purposes shall not relieve the Contractor of the responsibility to verify this through testing.

2. Transport waste in secured sealed labeled containers in such a manner to prevent leakage during transport to disposal site.

3. Reclamation reserves the authority to observe the sampling, transportation, and disposal of all components of the waste stream.

B. Nonhazardous Waste:

1. Store, transport, and dispose of nonhazardous waste debris in accordance with

Federal, State, and local requirements. In case of conflict, the most stringent regulation shall apply.

Revised 02 83 30 - 21

2. Store nonhazardous coating debris in closed containers separate from hazardous waste storage areas.

3. Obtain and submit bills of lading from solid waste transporter and solid waste disposal facility.

C. Hazardous Waste:

1. Seal, label, and store hazardous coating debris in DOT-approved weatherproof, watertight steel containers (refer to HW 2005 G1 for details).

2. Do not co-mix different types of hazardous and non-hazardous waste materials.

3. Dispose of all hazardous waste at EPA-permitted RCRA Subtitle C TSD facility.

4. Before…