BLM LE Vehicle Up-Fitting

Specification Sheet BLM LE Vehicle Up-Fitting

COLORADO – NEW MEXICO

1.A. General: The Bureau of Land Management (BLM) requires the upfitting of a full-size crew cab truck to be used as marked law enforcement vehicle. The vendor will install and program the equipment with the specifications (Standard Features and Radio Specifications) listed below to ensure the law enforcement vehicle is equipped with emergency lighting, siren/PA systems, radios, gun locks, center consoles, partitions, agency markings, and fire extinguishers to meet the necessary operational standards and agency policy.. The government will provide for all equipment specified in part B of each section (if applicable).

1.B. PERIOD OF PERFORMANCE: The period of performance for this effort will commence on the date of the award and conclude at period of performance date determined upon award. The total period of performance for the upfitting of the vehicle under this contract shall not exceed 120 calendar days from the awarded date.

1.B.1. This period accommodates the following:

1.B.1.A. Delivery and Receiving of Parts: Up to 30 calendar days are allocated for the procurement and receipt of necessary parts and components required for the upfitting process.

1.B.1.B. Upfitting Work: The vendor shall complete the actual upfitting work within 45 calendar days following the receipt of all necessary parts and components.

1.B.2. It is the responsibility of the contractor to ensure timely ordering of parts to meet the performance schedule and to coordinate effectively with suppliers to minimize any potential delays. All work is to be completed in accordance with the specifications outlined in the contract. Should any unforeseen circumstances arise that may impact the timeline, the contractor must provide appropriate documentation and seek approval for any necessary adjustments to the schedule.

1.C. SECURITY

The vendor shall maintain a secure storage area while the vehicle is in their possession.

1.D. DELIVERY AND INSPECTION

Delivery including drop-off and pick-up of vehicle(s) and government provided equipment will be performed by the governments receiving official. Upon arrival at the vendor’s location, an initial inspection will be performed by the vendor representative in the presence of the government’s representative. This inspection will identify and document any existing defects, dents, scratches, or abnormalities present prior to vehicle acceptance. The government will be provided with a copy of the intake report. The contractor assumes risk of loss liability while vehicles are in their possession per FAR 52.212-4(j).

1.E. FINAL INSPECTION AND ACCEPTANCE OF UPFITTED VEHICLE

The government will provide for inspection pursuant to FAR 52.212-4(a).

1.F. DAMAGES / LIABILITY

During the pick-up of the completed vehicle, a final inspection will be conducted by a BLM representative with the vendor representative present. This inspection will identify any defects, dents, scratches, or abnormalities that may have occurred during the upfitting process. Any damage determined to have occurred during this period shall be repaired at the vendors expense within ten (10) business days.

1.G. WARRANTY

1.G.1. The vendor shall provide a standard commercial warranty pursuant to FAR 52.212-4(o). The contractor shall provide their express warranty with their quotation limited to those terms and conditions after government acceptance of the performance.

1.G.2. The vendor shall provide a one-year commercial warranty covering parts and labor for all vendor supplied equipment installed as part of this upfitting service. The warranty will begin on the date of final inspection and acceptance of the upfitted vehicle(s). The warranty will at minimum cover the following:

1.G.3. Parts and Labor: All vendor supplied equipment installed, including but not limited to emergency lighting systems, sirens, consoles, and mounting/wiring hardware, will be covered under the warranty for defects in materials or workmanship. This includes any necessary repairs or replacements due to failures in the installed equipment that occur during the warranty period.

1.G.4. Scope of Coverage: Defective Equipment: Any equipment that fails due to defects in materials or manufacturing will be repaired or replaced at the vendor's expense, including the cost of parts and labor.

1.G.5. Installation Issues: If any installed equipment fails due to improper installation or configuration, the vendor is responsible for correcting these issues without charge, including labor and any necessary adjustments to wiring, mounts, or connections.

1.G.6. Non-Coverage: The warranty does not cover damage resulting from accidents, misuse, unauthorized modifications, or normal wear and tear.

1.G.7. Warranty Claims: The Contracting Officer will notify the vendor by writing (email or formal report) of any equipment failure or defect covered by this warranty. Upon receipt of the claim, the vendor will confirm the issue and schedule the necessary repairs within ten (10) business days. All warranty-related repairs must be completed within ten (10) business days of the vehicle's arrival at the vendor’s facility, unless prior written approval for a longer timeline is obtained from the BLM representative. In case of exceptional circumstances requiring more time, the vendor must notify the BLM representative within two (2) business days to provide a timeline for completion.

2. Specified Tasks:

2.A.1. Scope: Decommission and remove all emergency equipment, lights, controllers, prisoner cage, storage and other items from older Chevy Silverado. Restore old Silverado to OEM condition, plug holes in roof, full function test of OEM components and safety check. Reuse and reinstall all compatible working equipment into new Silverado.

2.A.2 Provide and Install New Emergency Law Enforcement Equipment to include:

2.A.2.A. GRAPHICS PACKAGE. Install provided BLM Police Graphics package

2.A.2.B. WINDOW TINTING: Add 3M SAS/UV security impact resistant window film tint 20%, 4 mil thick to front and rear windows on driver and passenger windows

2.A.2.C. ACCESSORIES:

2.A.2.C.1. Tonneau Cover. Install provided HD tonneau cover

2.A.2.C.2. Front Bumper. Purchase/install Addictive Desert Designs front bumper F140152980103

2.A.2.C.3. Fuel Tank. Titan tanks titan fuel tanks 5040115 liquid transfer tank sidekick ii 15-gallon tank 5040115

2.A.2.C.4. Air Compressor. ARB CKMTA12KIT air compressor on-board 150 psi maximum working pressure 6.16 cubic feet per minute (CFM) at 0 psi/ 4.68 cubic feet per minute (CFM) at 29 psi 12 volt with twin on-board compressor/ sealed illuminated automotive grade dash switch/ full wiring loom with mounting bracket/ digital tire inflation chuck

2.A.2.C.5. Step Bars. Purchase and install Amp Research AMP Research PowerStep™ Plug-N-Play - 76255-01A or similar retractable step bars.

2.A.2.C.6. Computer Swing Arm. (Reuse/install from old Silverado). Troy sliding LECO dock mount (CM-SDMT-SL-LED)

2.A.2.C.7. Computer Dock. (Reuse/install from old Silverado). Dell latitude dock (S/N# I65F-A03)

2.A.2.C.8. Radar. (Reuse/install from old Silverado). Radar kustom (NEW - INVOICE 20384 / PO 21-0648)

2.A.2.C.9. (Reuse/install from old Silverado) Console-Jotto desk 20" std wide body console w/ locking lid 6445

2.A.2.C.10. (Reuse/install from old Silverado) Floor plate-Jotto desk Silverado floorplate

2.A.2.C.11. (Reuse/install from old Silverado) Abs dual cup holder face plate mount requires 4" of mounting space 425-3704

2.A.2.C.12. (Reuse/install from old Silverado) Laws power faceplate kit fits Jotto center console. Includes one (1) 12V DC power outlet and two (2) USB A/C charging ports.

2.A.2.C.13. (Reuse/install from old Silverado) Magnetic mic holders

2.A.2.C.14. (Reuse/install from old Silverado) Law padded arm rest with mount bracket

2.A.2.C.15. (Reuse/install from old Silverado) Setina prisoner cage- PK0115DRT191500, disable door release from inside door, disable door plunger and window switch for prisoner cage

2.A.2.C.16. (Reuse/install from old Silverado) Warn Zenon series winch with Spydura synthetic rope 103251

2.A.2.C.17. (Reuse/install from old Silverado) Amarex 5.0 lb class A/B/C dry chem fire extinguisher B500T

2.A.2.C.18. (Reuse/install from old Silverado) Flashlight charging mount-Streamlight Stinger 2020 120v/12v DC holder (black) 78101

2.A.2.C.19. (Reuse/install from old Silverado) 2 drawer weatherproof vault for bed of truck. Will have filler plates on the side so customers are still able to make full use of truck bed. Paddle style latch. Dimensions: 48"W x 12"H x 60" L

2.A.2.C.20. (Reuse/install from old Silverado) Remove rear seat drivers’ side and reinstall storage system dual shelf open with under equipment storage

2.A.2.D. ELECTRICAL.

2.A.2.D.1. 100 AMP Circuit Breaker with isolation on/off switch, needed wiring, harness, looming, programming and shop supplies, all power routed through master switch on console

2.A.2.D.2. Link module 2025+- Sound Off Blueprint link for Tahoe / Silverado / Sierra /Yukon / savanna vans. 15-20 ENGLNK004

2.A.2.D.3. Node-sound off remote node for use with Sound Off Signal Blueprint Model: ENGND04102

2.A.2.D.4. Node harness- Sound Off node harness kit ENGHNK05

2.A.2.E. EXTERIOR LIGHTING

2.A.2.E.1. Unity post mount x head led spotlight. X218036-0002 drivers side bracket for 2019 Silverado 8938

2.A.2.E.2. Front bumper light- sound off Whelan MPOWER Series Duo warning bar with flood feature.

2.A.2.E.3. Silicone encased light modules x 4 red/blue with white flood. Model: Emptc01mch

2.A.2.E.4. 60" led warning strip red and white.180 SM-LED / ip66 waterproof housing / with flasher versa RL60D under rails on left and right side of bed

2.A.2.E.5. Whelan LS3 single-side window mount shroud. Accept one MPOWER or tri-color light. Zero flashback shroud. SHD side SGL

2.A.2.E.6. High intensity 921 / t15 reverse & fog light led bulb -white (each). 80-watt eq. LAWS921LED

2.A.2.E.7. High intensity 7443 / 7440 brake light led bulb - red(each) 80-watt output LAWS7443LED-R

2.A.2.E.8. Laws Versa 48" dual color warning strip light. Red/blue IP67 rated with internal in line flasher. LAWS-VSA-(LAWS VERSA REUSE)

2.A.2.E.9. Purchase and install interior visor lights with red and blue programmable flashing patterns and steady white capability, lights to split and cover front driver and passenger side visor area, similar in style to Feniex Fusion Interion Red and Blue or Whelen Inner Edge FST.

2.A.2.E.10. (Reuse/install from old Silverado).Side/grille- LAWS GAMMA fx6 dual color red/white silicone OPTIC FX6RW 01035776266778

2.A.2.E.11. (Reuse/install from old Silverado). Side/grille- LAWS GAMMA FX6 dual color blue / white. Silicone OPTIC FX6 BW 01035776266777

2.A.2.E.12. (Reuse/install from old Silverado). Baja Designs led cube light spot / flood (installed in front bumper light pockets)

2.A.2.E.13. (Reuse/install from old Silverado). Mirror- Sound Off Signal Intersector led light split color (red/white) ENT2B3D

2.A.2.E.13. (Reuse/install from old Silverado). Mirror- Sound Off Signal Intersector LED light split color (blue/white) ENT2B3E

2.A.2.F. AUDIO

2.A.2.F.1. Siren speaker Sound Off Signal 100-watt siren speaker. ETSS100 includes mounting bracket

2.A.2.F.2. (Reuse/install from old Silverado). Sound Off 500 Series Blueprint controller remote head controller 200-watt dual tone siren. ENGSA5200RSP

2.A.2.G. INTERIOR LIGHTING. RESERVED

2.A.2.H. WEAPONS STORAGE

2.A.2.H.1. (Reuse/install from old Silverado). Gun locks and butt plates, dual gun lock release switches - one on controller and second low on driver’s side b pillar. On timed release. Add bracket that prevents charging handle from moving while in gun rack

2.A.2.I. COMMUNICATIONS EQUIPMENT

2.A.2.I.1. Purchase/install Weboost drive reach fleet cell booster

2.A.2.I.2. (Reuse/install from old Silverado). Motorola APX 8500 mobile radio – radio brain mounted behind passenger seat on front of transport cage or where there is quick access)

2.A.2.J. SYSTEM PROGRAMMING. Programming patterns/controller programing for buttons and lights to be discussed when upfit work is performed.

2.B.1. Scope: The vehicle will arrive for upfitting with aftermarket front bumper installed, radio console installed without faceplates, computer pedestal/mount, under seat storage box and partial prisoner cage(not fully installed to allow for ceiling headliner access) Motorola radio provided for install, KC Flood and IR lights provided and mounted to bumper to be wired, gun locks/t-slot rails provided to be wired to installed system.

2.B.2 Provide and Install New Emergency Law Enforcement Equipment to include:

2.B.2.A. GRAPHICS PACKAGE. Install provided BLM Police Graphics package

2.B.2.B. WINDOW TINT: Install 3M SAS UV 20%, security film 4mm thick window film to front and rear windows

2.B.2.C. ACCESSORIES: RESERVED

2.B.2.D. ELECTRICAL:

2.B.2.D.1. 100 AMP Circuit Breaker with isolation on/off switch, needed wiring, harness, looming, programming and shop supplies, all power routed through master switch on console

2.B.2.D.2. For wiring routed through and in engine compartment, wrap in design engineering heat sheath or similarly rated wire heat wrap where needed

2.B.2.D.3. Whelen Core 21 Button Controller Head (wired to turn off/on with master switch)

2.B.2.D.4. Whelen Cencom Core full vehicle control system (mount in console or under prisoner seat where makes most sense for install)

2.B.2.D.5. Whelen vehicle interface kit for 26 Ford F250

2.B.2.D.6. Whelen 16 output, 4 input expansion modules (if needed)

2.B.2.D.7. Install Rocker switches, small circular with red LED lights on console for aux light control (IR, KC lights)

2.B.2.D.8. Wire/Connect already installed KC Hilites Flex Era 4 2light 0289 to small circular rocker switch on console, switch to have red led indicating switch is on

2.B.2.D.9. Wire provided/installed IR lights on bumper to be controlled by to small circular rocker switch on console, switch to have red led indicating switch is on

2.B.2.D.10. Two (2) 12 volt and Two (2) USB-C accessory ports on console ports or drill to fit, fused/wired to 12-volt fuse board in console

2.B.2.D. Two (2) additional 12-volt ports to passenger side console fused to board in console

2.B.2.E. EXTERIOR LIGHTING:

2.B.2.E.1. Whelen ION-T trio red/blue/white surface-mount, smoked lens (12 total) –

2.B.2.E.1.A. Two (2) behind front grille, 2.B.2.E.1.B. Two (2) on tailgate (on upper 2/3 of gate, midway between center and edges), 2.B.2.E.1.C. Two (2) under tailgate

2.B.2.E.1.D. Two (2) on forward fender (One (1) in front of front doors each side, centered above front wheel on body)

2.B.2.E.1.E. Two (2) on rear fenders (One (1) above rear wheel both sides, centered above wheel on body)

2.B.2.E.1.F. Two (2) on front bumper angles (will provide photo sample to vendor upon contracting approval)

2.B.2.E.2. LED Spotlight – driver A-pillar - unity C335 / model S-14 or similar, black shell

2.B.2.E.3. Headlight flasher

2.B.2.E.4. Taillight flasher

2.B.2.E.5. High Intensity reverse/fog light

2.B.2.E.6. High intensity brake and taillight

2.B.2.E.7. Purchase/install interior visor lights with red and blue programmable flashing patterns and steady white capability, lights to split and cover front driver and passenger side visor area, similar in style to Feniex Fusion Interior Red and Blue or Whelen Inner Edge FST

2.B.2.F. AUDIO:

2.B.2.F.1. Siren- Whelen weather resistant siren (On bumper or under front of truck bumper: not to protrude beyond front of bumper)

2.B.2.F.2. Magnetic mic mounts for radio mic and PA mic

2.B.2.G. INTERIOR LIGHTING (Blackout module)

2.B.2.G.1. Red/white led to be installed in ceiling liner above prisoner seating, switch control on core faceplate, red/white led light to be installed in ceiling liner above driver seat, 2.B.2.H. WEAPONS STORAGE: Gun mounts/locks provided BLACRAC 1082 electric AR 15 rifle lock and and cuff style shotgun lock, install and wire to have dual gun lock release switches – one (1) on core controller and one (1) switch low on drivers side b pillar. Eight (8) second timed release

2.B.2.I. COMMUNICATIONS EQUIPMENT:

2.B.2.I.1. Install provided Motorola APX 8500 Mobile Radio – Radio brain mounted behind front passenger seat or under prisoner seat storage compartment where there is quick access for reprogramming) wired to turn off and on with master switch

2.B.2.I.2. Headliner Radio Speaker, flush marine style 3-4” pair wired to audio from radio, install in center headliner, closet to windshield/interior lights

2.B.2.I.3. Install provided radio roof antennas

2.B.2.I.4. Radio broadcast through siren speaker

2.B.2.I.5. Install any other items not listed needed for emergency lights/radio/wiring.

2.B.2.J. SYSTEM PROGRAMMING: Programming patterns/controller programing for buttons and lights to be discussed when upfit work is performed.

Contact:

2.C.1. Scope: Decommission and remove all emergency equipment, lights, controllers, prisoner cage, storage and other items from older Ram Powerwagon. Restore Power wagon to OEM condition, remove decals striping, plug holes in roof/light holes, full function test of OEM components and safety check. Install OEM center seat and OEM bumper (provided), Remove truck vault, bumper, window bars, spotlights (save) Remove cage, console, laptop mount, blackout module (trash)

2.C.2 Provide and Install New Emergency Law Enforcement Equipment to include:

2.C.2.A. GRAPHICS PACKAGE: Install provided BLM Police Graphics package

2.C.2.B. WINDOW TINTING

2.C.2.C. ACCESSORIES

2.C.2.C.1. Buckstop bumper – Model: Classic 1

2.C.2.C.2. Computer dock station - $1325 Docking Station for Dell Pro Rugged 14" & 13", 5430, 7330, 5420, 5424, & 7424 Notebooks with Advanced Port Replication & Havis Power Supply | DS-DELL-432N | Havis Inc NRL

2.C.2.C.2. Warn Winch M15-S Heavyweight -item 97 730 (On bumper: NOT TO PROTRUDE BEYOND BUMPER)

2.C.2.C.3. Computer dock station - Docking Station for Dell Pro Rugged 14" & 13", 5430, 7330, 5420, 5424, & 7424 Notebooks with Advanced Port Replication & Havis Power Supply | DS-DELL-432N | Havis Inc NRL

2.C.2.C.4. Computer dock station pole mount/ pedestal – Havis

2.C.2.C.5. Cage – ½ prisoner partition. Manufacturer TBD, Window bars – rear psgr window, Disable Door release from inside door, disable door plunger and window switch for prisoner cage

2.C.2.C.6. Truckvault –- all weather – 5.5 bed – extended height – offset drawers – gray-black composite – no dividers

2.C.2.D. ELECTRICAL

2.C.2.D.1. Battery jump connector (On bumper: NOT TO PROTRUDE BEYOND BUMPER)

2.C.2.D.2. 100 AMP Circuit Breaker with isolation on/off switch, needed wiring, harness, programming and shop supplies, all power routed through master switch on console

2.C.2.D.3. Center console Troy with armrest for 2 radio (transfers)

2.C.2.D.4. Two rocker switches (new/transfer) to console for aux light control (IR, yellow,)

2.C.2.D.5. (Reuse/install from old Powerwagon). Axon fleet 3 system (camera/brain/Wi-Fi)

2.C.2.D.6. (Reuse/install from old Powerwagon). Light Controller Whelen Core 21 button

2.C.2.E. EXTERIOR LIGHTING

2.C.2.E.1. ION-T trio red/blue/white surface-mount (12 of them)

2.C.2.E.1.A. Two (2) behind grille

2.C.2.E.1.B. Two (2) on tailgate

2.C.2.E.1.C. Two (2) on front fenders (One (1) in front of doors both side)

2.C.2.E.1.D. Two (2) on rear fenders (One (1) above rear wheel both sides)

2.C.2.E.1.E. Two (2) on front bumper angles

2.C.2.E.1.F. Two (2) under rear tailgate above bumper (new)

2.C.2.E.2. Spotlight – driver A-pillar - unity C335 / model S-14

2.C.2.E.3. Headlight flashers

2.C.2.E.4. Taillight flashers

2.C.2.E.5. Taillight flasher On-tri trios x 12 – red/blue/white

2.C.2.E.6. (Reuse/install from old Powerwagon). Center White KC light (On bumper: NOT TO PROTRUDE BEYOND BUMPER)

2.C.2.E.7. (Reuse/install from old Powerwagon). Two (2) Side KC lights (On bumper: NOT TO PROTRUDE BEYOND BUMPER)

2.C.2.E.8.(Reuse/install from old Powerwagon). IR light (On bumper: NOT TO PROTRUDE BEYOND BUMPER)

2.C.2.E.9. (Reuse/install from old Powerwagon). Roof Light Bar

2.C.2.F. AUDIO

2.C.2.F.1. Siren- Whelen SA 315 (On bumper: NOT TO PROTRUDE BEYOND BUMPER)

2.C.2.F.2. (Reuse/install from old Powerwagon). Siren Howler (On bumper: NOT TO PROTRUDE BEYOND BUMPER)

2.C.2.G. INTERIOR LIGHTING. Blackout module

2.C.2.H. WEAPONS STORAGE.

2.C.2.H.1. Gun mounts/locks Setina Blacrac (rifle with charging handle block and shotgun mounts) dual gun lock release switches - one on controller and second low on drivers side B pillar. Both on timed release.

2.C.2.I. COMMUNICATIONS EQUIPMENT

2.C.2.I.1. Radio speaker, ceiling mount – Motorola HSN4032B

2.C.2.I.2. (Reuse/install from old Powerwagon). Motorola APX 8500 Mobile Radio – Radio brain mounted behind passenger seat on front of transport cage or where there is quick access)

2.C.2.I.3. (Reuse/install from old Powerwagon). Bendix Radio

2.C.2.I.4. (Reuse/install from old Powerwagon). Radio roof antennae’s

2.C.2.I.5. (Reuse/install from old Powerwagon). Radio broadcast through siren speaker

2.C.2.I.6. (Reuse/install from old Powerwagon). Cellular Phone booster

2.C.2.I.7. Magnetic mic mounts

2.C.2.J. SYSTEM PROGRAMMING. Programming patterns/controller programing for buttons and lights to be discussed when upfit work is performed.

2.D.1. Scope: The Bureau of Land Management (BLM) requires the upfitting of a full-size crew cab truck to be used as marked law enforcement vehicle. The vendor will install and program the equipment with the specifications (Standard Features and Radio Specifications) listed below to ensure the law enforcement vehicle is equipped with emergency lighting, siren/PA systems, radios, gun locks, center consoles, partitions, agency markings, and fire extinguishers to meet the necessary operational standards and agency policy

2.D.2 Provide and Install New Emergency Law Enforcement Equipment to include:

2.D.2.A. GRAPHICS PACKAGE: Application of agency vehicle graphics (Government furnished pre-cut graphics for lettering, badges, flags, and BLM logos).

2.D.2.B. WINDOW TINTING

2.D.2.B.1. 40% Tint for All Windows over OEM

2.D.2.C. ACCESSORIES

2.D.2.C.1. Manufacturer's Info. Pouch and Fire Extinguisher with mount 2.D.2.C.2. Hardware Package (All hardware required to install up-fit equipment, i.e. screws, washers, nuts, and rivets, etc) 2.D.2.C.3. Equipment Mounting Plate 2.D.2.C.4. Vehicle specific console w/ Map Light, Dual Power Outlets & USB-C, Inset Cup Holders, Securable Box, Armrest 2.D.2.C.5. Single Detainee Security Partition w/ Kick Panels & Mounting Kit 2.D.2.C.6. Window Security Screens (Includes all Passenger Area Windows) 2.D.2.C.7. Aluminum Door Skins 2.D.2.C.8. Manual Locking/Unlocking Device in Rear Passenger Doors (Accessible to Officers Only) 2.D.2.C.9. Universal Laptop Tray, 11.75" X 17", Finger Clamp, Swing Arm w/ Console Mounted Stand 2.D.2.C.10. Protective Interior Floor Mat/ Driver and Passenger Side 2.D.2.C.11. Standard Fuel Fee (5 Gallons or 1/4 Tank) for Delivered Vehicles 2.D.2.C.12. Bed mounted storage box - 14"W x 14"H x 40"D 2.D.2.C.13. Full Skid Plate Kit 2.D.2.C.14. Diamond Plate Aluminum Tonneau Cover, Three Lockable Hatches, Color Black

2.D.2.D. ELECTRICAL

2.D.2.D.1. Wire Harness & Fuse block (All wiring and fuse blocks necessary to up-fit the vehicle, to include a Programable Timer) 2.D.2.D.2. Standard Console Siren Controller w / Traffic Advisor & 100 Watt Speaker

2.D.2.E. EXTERIOR LIGHTING

2.D.2.E.1. Grille Lights Alternating Single Red & Single Blue with Bracket 2.D.2.E.2. Roof Mounted LED Lightbar w/ Traffic Advisor, Full Takedowns, & a Solar Battery Tender 2.D.2.E.3. Front Alternating Headlight Flasher or WigWag in Front Grille 2.D.2.E.4. Front Intersection LED Lights - Single Red/White on Driver Side & Single Blue/White on Passenger Side 2.D.2.E.5. Rear Facing Alternating Single Red & Single Blue on Driver Side With Shroud 2.D.2.E.6. Rear Intersection LED Lights - Side Facing Red & Side Facing Blue 2.D.2.E.7. Rear Alternating Tail Light Flasher 2.D.2.E.8. Dual Front Facing 6X4 White LED Lights w/ Toggle Switch

2.D.2.F. AUDIO

2.D.2.G. INTERIOR LIGHTING

2.D.2.H. WEAPONS STORAGE

2.D.2.H.1. Dual gun lock assembly for M4 Rifle & Shotgun 2.D.2.H.1.A. The assembly shall be configured for installation in the driver/officer compartment, ensuring access to both weapons from the seated operator position while maintaining secure retention during vehicle operation.

2.D.2.H.1.B. Shotgun lock: Clasp or handcuff style barrel retention system engineered to accommodate shotguns equipped with a side‑saddle ammunition carrier.

2.D.2.H.1.C. M4 Rifle lock: Lower receiver clamping mechanism that uses dual opposing side plates to secure weapons.

2.D.2.H.2. Two electronically controlled weapon lock releases:

2.D.2.H.2.A. Primary Release: Electrically integrated into the emergency lighting/siren controller unit as a designated button. Activation shall momentarily energize the gun‑lock solenoids in accordance with the weapon lock manufacturer’s specifications.

2.D.2.H.2.B. Secondary Release: Wired release button installed on the underside of the lower steering column shroud. Wiring shall be routed using protective loom, secured away from moving steering components, heat sources, or potential pinch points. The secondary button shall function as a redundant release pathway, activating the weapon lock solenoids independently of the controller unit.

2.D.2.I. COMMUNICATIONS EQUIPMENT

2.D.2.I.1. Portable Radio Charger APX8000 2.D.2.I.2. Installation of 2 government furnished communication radios including all band mobile and satellite radio (See radio specifications section B).

2.D.2.I.3. Motorola APX-8500, all band, high power, including power supply, wiring, speaker, and antennas(Government furnished equipment includes radio unit, mic/controller, wiring, antennas, mounts,and speaker).

2.D.2.I.4. Installation of Skymira Explorer Satellite Radio Unit, including power supply, wiring, speaker, and roof mounted Starlink Mini satellite antenna. (Government furnished equipment includes radio unit, wiring, antennas, mounts, mic, and speaker).

2.D.2.J. SYSTEM PROGRAMMING. Programming patterns/controller programing for buttons and lights to be discussed when upfit work is performed.

2.E.1 Scope: The Bureau of Land Management (BLM) requires the upfitting of a full-size crew cab truck to be used as marked law enforcement vehicle. The vendor will install and program the equipment with the specifications (Standard Features and Radio specifications) listed below to ensure the law enforcement vehicle is equipped with emergency lighting, siren/PA systems, radios, gun locks, center consoles, partitions, agency markings, and fire extinguishers to meet the necessary operational standards and agency policy.

2.E.2. Provide and Install New Emergency Law Enforcement Equipment to include:

2.E.2.A. GRAPHICS PACKAGE: Application of agency vehicle graphics (Government furnished pre-cut graphics for lettering, badges, flags, and BLM logos).

2.E.2.B. WINDOW TINTING

2.E.2.B.1. Apply 40% Tint for All Windows over OEM

2.E.2.C. ACCESSORIES

2.E.2.C.1. Manufacturer's Info. Pouch and Fire Extinguisher with mount

2.E.2.C.2. Hardware Package (All hardware required to install up-fit equipment, i.e. screws, washers, nuts, and rivets, etc)

2.E.2.C.3. Equipment Mounting Plate

2.E.2.C.4. Vehicle specific console w/ Map Light, Dual Power Outlets & USB-C, Inset Cup Holders, Securable Box, Armrest

2.E.2.C.5. Single Detainee Security Partition w/ Kick Panels & Mounting Kit

2.E.2.C.6. Window Security Screens (Includes all Passenger Area Windows)

2.E.2.C.7. Aluminum Door Skins

2.E.2.C.8. Manual Locking/Unlocking Device in Rear Passenger Doors (Accessible to Officers Only)

2.E.2.C.9. Universal Laptop Tray, 11.75" X 17", Finger Clamp, Swing Arm w/ Console Mounted Stand

2.E.2.C.10. Protective Interior Floor Mat/ Driver and Passenger Side

2.E.2.C.11. Standard Fuel Fee (5 Gallons or 1/4 Tank) for Delivered Vehicles

2.E.2.C.12. Full Skid Plate Kit

2.E.2.C.13. Diamond Plate Aluminum Tonneau Cover, Three Lockable Hatches, Color Black

2.E.2.D. ELECTRICAL

2.E.2.D.1. Wire Harness & Fuse block (All wiring and fuse blocks necessary to up-fit the vehicle, to include a Programable Timer)

2.E.2.D.2. Standard Console Siren Controller w / Traffic Advisor & 100 Watt Speaker

2.E.2.E. EXTERIOR LIGHTING

2.E.2.E.1. Grille Lights Alternating Single Red & Single Blue with Bracket

2.E.2.E.2. Roof Mounted LED Lightbar w/ Traffic Advisor, Full Takedowns, & a Solar Battery Tender

2.E.2.E.3. Front Alternating Headlight Flasher or WigWag in Front Grille

2.E.2.E.4. Front Intersection LED Lights - Single Red/White on Driver Side & Single Blue/White on Passenger Side

2.E.2.E.5. Rear Facing Alternating Single Red & Single Blue on Driver Side With Shroud

2.E.2.E.6.Rear Intersection LED Lights - Side Facing Red & Side Facing Blue

2.E.2.E.7. Rear Alternating Tail Light Flasher

2.E.2.E.8. Dual Front Facing 6X4 White LED Lights w/ Toggle Switch

2.E.2.F. AUDIO

2.E.2.G. INTERIOR LIGHTING

2.E.2.H. WEAPONS STORAGE

2.E.2.H.1. Dual gun lock assembly for M4 Rifle & Shotgun

2.E.2.H.1.A. The assembly shall be configured for installation in the driver/officer compartment, ensuring access to both weapons from the seated operator position while maintaining secure retention during vehicle operation.

2.E.2.H.1.B. Shotgun lock: Clasp or handcuff style barrel retention system engineered to accommodate shotguns equipped with a side‑saddle ammunition carrier.

2.E.2.H.1.B.1. M4 Rifle lock: Lower receiver clamping mechanism that uses dual opposing side plates to secure weapon.

2.E.2.H.2. Two electronically controlled weapon lock releases:

2.E.2.H.2.A. Primary Release: Electrically integrated into the emergency lighting/siren controller unit as a designated button. Activation shall momentarily energize the gun‑lock solenoids in accordance with the weapon lock manufacturer’s specifications.

2.E.2.H.2.B. Secondary Release: Wired release button installed on the underside of the lower steering column shroud. Wiring shall be routed using protective loom, secured away from moving steering components, heat sources, or potential pinch points.

The secondary button shall function as a redundant release pathway, activating the weapon lock solenoids independently of the controller unit.

2.E.2.I. COMMUNICATIONS EQUIPMENT

2.E.2.I.1. Portable Radio Charger APX8000

2.E.2.I.2. Installation of 2 government furnished communication radios including all band mobile and satellite radio (See radio specifications section B).

2.E.2.I.3. Motorola APX-8500, all band, high power, including power supply, wiring, speaker, and antennas (Government furnished equipment includes radio unit, mic/controller, wiring, antennas, mounts, and speaker).

2.E.2.I.4. Installation of Skymira Explorer Satellite Radio Unit, including power supply, wiring, speaker, and roof mounted Starlink Mini satellite antenna. (Government furnished equipment includes radio unit, wiring, antennas, mounts, mic, and speaker).

2.E.2.J. SYSTEM PROGRAMMING

2.F.1. Scope: The Bureau of Land Management (BLM) requires installation of a manual door lock/unlock device that will allow authorized officers to access the prisoner transport area of a 2023 Ram 2500 truck. This installation must ensure safe, reliable, and secure operation consistent with law enforcement transport standards and applicable agency policy.

2.F.2. Provide and Install New Emergency Law Enforcement Equipment to include:

2.F.2.A. GRAPHICS PACKAGE:

2.F.2.B. WINDOW TINTING

2.F.2.C. ACCESSORIES

2.F.2.C.1. The vendor shall install a manual locking/unlocking mechanism for the rear passenger door providing controlled officer-only access to the prisoner transport area.

2.F.2.C.1.A. The system must allow officers to manually lock or unlock the rear passenger door from the front passenger door jam to access the prisoner transport compartment.

2.F.2.C.1.B. The design and installation must ensure that detainees cannot manipulate, access, or tamper with the locking mechanism from within the transport area.

2.F.2.C.1.C. All components, brackets, hardware, and related materials necessary to complete the installation shall be included.

2.F.2.C.1.D. Installation must not interfere with existing safety systems, door operation, or factory-installed components.

2.F.2.C.1.E. Upon award, the vendor will meet with a BLM representative within 10 business days to review installation requirements and confirm configuration details.

2.F.2.D. ELECTRICAL

2.F.2.E. EXTERIOR LIGHTING

2.F.2.F. AUDIO

2.F.2.G. INTERIOR LIGHTING

2.F.2.H. WEAPONS STORAGE

2.F.2.I. COMMUNICATIONS EQUIPMENT

2.F.2.J. SYSTEM PROGRAMMING

2.G.1. Scope: The vehicle will arrive for upfitting with aftermarket front bumper installed, radio console installed without faceplates, computer pedestal/mount, under seat storage box and partial prisoner cage(not fully installed to allow for ceiling headliner access) Motorola radio provided for install, KC Flood and IR lights provided and mounted to bumper to be wired, gun locks/t-slot rails provided to be wired to installed system

2.G.2 Provide and Install New Emergency Law Enforcement Equipment to include:

2.G.2.A. GRAPHICS PACKAGE: Application of GFM Graphics

2.G.2.B. WINDOW TINTING

2.G.2.B.1. Apply 40% Window Tint (All Three Sides & Eyebrow)

2.G.2.C. ACCESSORIES

2.G.2.C.1. Manufacturer's Information Storage Pouch 2.G.2.C.2. Fire Extinguisher w/ Bracket

2.G.2.C.3. Siren Controller Mounting Bracket 2.G.2.C.4. Siren Speaker Mounting Bracket 2.G.2.C.5. Rear Facing LED Housing Bracket 2.G.2.C.6. Floor Mount for Fire Extinguisher & Bracket 2.G.2.C.7. Fuse Box Mount 2.G.2.C.8. Upfit Hardware Pack 2.G.2.C.9. Security Kit 2.G.2.C.10. Console (Armrest, Dual Power Outlets & Single USB-C, Inset Cup Holder, 7" Lock Box, Map Light, Magnetic Mic)

2.G.2.C.11. Rear & Passenger Window Screens

2.G.2.C.12. Passenger Door Skin

2.G.2.C.13. Single Detainee w/ Plastic Seat & Half Partition

2.G.2.C.14. Rear Door Lock Rods

2.G.2.C.15. Single Side Storage Box (20" W x 40" D x 14" H)

2.G.2.C.16. Aluminum Tri-Fold Tonneau Cover, Black

2.G.2.C.17. Console Mount Laptop Stand for Ford F150

2.G.2.C.18. Floor Mats

2.G.2.C.19. Skid Plates for 2026 Ford F150

2.G.2.C.20. Upfit Shop Supplies

2.G.2.D. ELECTRICAL

2.G.2.D.1. 26 Circuit Wire Harness w/ Timer

2.G.2.D.2. Siren Controller with Traffic Advisor

2.G.2.E. EXTERIOR LIGHTING

2.G.2.E.1. Alternating Taillight Flasher 2.G.2.E.2. Alternating Head Light Flasher 2.G.2.E.3. Grille LEDs (1-Solid Red & 1-Solid Blue) 2.G.2.E.4. Front Intersection LEDs (1-R/W & 1-B/W) 2.G.2.E.5. Rear Facing LEDs (1-Solid Red & 1-Solid Blue) 2.G.2.E.6. Rear Intersection LEDs (1-Solid Red & 1-Solid Blue) 2.G.2.E.7. Red/Blue Standard Lightbar with Traffic Advisor 2.G.2.E.8. Dual Front Facing 6x4 LED Lights w/ Switch

2.G.2.F. AUDIO

2.G.2.F.1. 100-Watt Siren Speaker

2.G.2.G. INTERIOR LIGHTING

2.G.2.H. WEAPONS STORAGE

2.G.2.H.1. Stand Alone Gun Lock System for 1- AR & 1- Shotgun

2.G.2.I. COMMUNICATIONS EQUIPMENT

2.G.2.I.1. Install GFM COBHAM Explorer Satellite Radio with Starlink Antenna 2.G.2.I.2. Install GFM Motorola APX-8500 Radio with Antenna 2.G.2.I.3. Portable Handheld Radio Charger

2.G.2.I.4. Motorola APX-8500, remote control head, dual band, high power, including antennas (Government furnished equipment)

2.G.2.I.5. COBHAM Push to talk Satellite Radio Unit with Power Supply, Wiring, and Starlink antenna (Government furnished equipment)

2.G.2.I.6. COBHAM Explorer SatRad radio with Starlink wiring diagram and installation materials included as attachment

2.G.2.J. SYSTEM PROGRAMMING