B09_Amend-P0003-To_add_inspection_report_0003.pdf

319 E. Banbury Dr., Stockton CA 95207 Tel (209) 451-3017 www.stocktonenvironmentalinc.com

ASBESTOS & LEAD

INSPECTION

CONDUCTED AT:

2714 Dairy Rd.

Vernalis, CA 95385

“House and Barn – Demolition Inspection”

PREPARED FOR:

TRCH O.R,.

22350 W Warren Ave

Detroit, MI 48239

C/o Zoubair Telouati

PREPARED BY:

Stockton Environmental, Inc.

Report No.041.26 Asb/Pb

03/22/2026 04/06/2026 R2

Asbestos & Lead Sampling 041.26Asb/Pb R2 2714 Dairy Rd (house and barn) pg. 2

TABLE OF CONTENTS

Inspection Report

Executive Summary Page 3 - 4

Survey Methodology Page 4

Summary of Readings Page 4 - 5

Laboratory Results Page 5 - 7

Recommendations Page 7

Exclusions and Report Limitations Page 7

APPENDICES

Site Diagrams Appendix A

Laboratory Reports Appendix B

Certifications Appendix C

2714 Dairy Rd (house and barn) pg. 3

EXECUTIVE SUMMARY

Introduction:

On March 12, 2026, Stockton Environmental Inc. (SEI) performed an inspection for Asbestos- Containing Materials (ACM) and Lead Based Paint (LBP). Mr. Gabriel Munoz and Frank Ramos conducted asbestos and lead sample collection services for SEI. Mr. Munoz , a Certified Asbestos Consultant (certificate number 24-7549) and Mr. Ramos a California Department of Public Health (CDPH) accredited Sampling Technician for Lead (CDPH # 00002683) under the direction of Mr. Randolph Brooke, a Public Health (CDPH) accredited Lead Inspector (CDPH #00002684).

Scope of Services:

The Asbestos inspection was conducted to identify the presence of any Regulated Asbestos Containing Materials (RACM) (within the specified scope) in accordance with the Federal Environmental Protection Agency Regulation 40 CFR Part 763.85 and the local Air Pollution Control District’s Asbestos Notification and Inspection Requirements.

SEI’s Lead inspection was conducted to identify Lead Based Paint (LBP) by either collecting paint chip samples and/or a surface-by-surface investigation using X-Ray Fluorescence (XRF) Readings in compliance with the U.S Environmental Protection Agency (EPA) regulatory requirements & Department of Housing and Urban Development (HUD) Guidelines between October 17, 2019 & October 22, 2019.

This document is prepared for the sole use of Stockton Environmental Inc. (SEI), Its client, and any regulatory Agencies that are directly involved in this project. No other party should rely on the information contained herein without prior written consent of SEI.

Regulatory Limits:

Asbestos

• Federal regulations define “Asbestos Containing Material (ACM)” as containing 1.0% or greater of asbestos by weight.

• California OSHA defines “Asbestos Containing Construction Material (ACCM)” as 0.1% or greater asbestos by weight. Note: neither Federal nor California OSHA define a minimal regulatory level for compliance with employee exposure requirements.

• California Business & Professions Code Division 3, Chapter 9. Contractors, Article 4.

Classifications 7058.5. (a) - No contractor shall engage in asbestos-related work, as defined in Section 6501.8 of the Labor Code, which involves 100 square feet or more of surface area of asbestos containing materials, unless the qualifier for the license passes an asbestos certification examination.

Local Air Quality District define asbestos as

• RACM – Regulated Asbestos Containing Material means (a) friable ACM, (b) Category I non-friable ACM that has become friable, (c) Category I non-friable ACM

2714 Dairy Rd (house and barn) pg. 4 that will be subjected to sanding, grinding, cutting or, abrading, or (d) Category II non-friable ACM that has a high probability of becoming or has become crumbled, pulverized, or reduced to powder by the forces expected to act on the material in the course of demolition or renovation operations.

• Category I non-friable asbestos-containing material (ACM) means asbestos-containing packings, gaskets, resilient floor cover, and asphalt roofing products containing more than 1 percent asbestos.

• Category II non-friable ACM means any material excluding Category I non-friable ACM containing more than 1 percent asbestos.

Written notification to the district is required for the following:

1. Any regulated demolition, whether asbestos is present or not.

2. Any regulated renovation in which the following will be disturbed:

• 160 square feet or more of regulated asbestos-containing materials or,

• 260 linear feet or more of regulated asbestos-containing pipe insulation.

Lead Paint Chip

• OSHA regulations define Lead Based Paint (LBP) as containing 0.5% or greater of lead by weight.

• Federal EPA regulations define Lead Hazardous Waste” (>50 mg/kg) via Total Threshold Limit Concentration (TTLC) method.

• The Consumer Product Safety Commission (CPSC) bans consumer paints and surface coatings containing more than 0.009% (90 ppm) lead, Note: neither Federal nor California OSHA define a minimal regulatory level for compliance with employee exposure to lead.

SURVEY METHODOLOGY

Sample Collection:

A walk through of the subject site was conducted to identify homogeneous suspect materials and their respective locations. This information was then used to develop a sample collection strategy. Each suspect sample was sealed in its own zip lock plastic container and labeled with a unique identification number. Sampling tools were individually cleaned before and after each sample was collected to avoid sample cross contamination. Decontamination was accomplished using individual use, pre-moistened cloths.

SUMMARY OF READINGS

Asbestos - SEI's inspection of the subject site collected Twenty-Three (23) bulk samples of suspect materials in which the laboratory determined Twenty-Six (26) materials for analysis.

Laboratory report(s) attached as Appendix B.

2714 Dairy Rd (house and barn) pg. 5

Asbestos Material Specific Location(s)

Asbestos Content Percent / Method

EPA/AQMD

Category

Sheetrock-Mud/Tape - White Though out House Est. - > 160 sq. ft.

<1%

0.25 Chrysotile

NA

Friable

Texture atop Sheetrock-Mud/Tape - White Though out House Est. - > 160 sq. ft.

<1%

0.25 Chrysotile

NA

Friable

* Quantities are for regulatory reference, not for bidding purposes. Contractors should field quantify if no scope of work is developed. ** Based on greater than 100 sq. ft. being impacted. ***Recommend conformational Point Count analysis.

Lead Paint Chip- SEI's inspection of the subject site collected a total of Seven (07) samples for analysis.

The following samples collected were reported at or above the EPA’s definition of “Lead Based Paint” (0.5% by wt.):

Sample # Paint Color / Area / Sample Location Lead % by weight

0312.L5 Paint – 1x1 – Wood – White Exterior Wall

4.82%

0312.L6 Paint – 1x1 – Wood – White Exterior Wall

3.90%

0312.L7 Paint – 1x1 – Wood – White Exterior Facia

5.18%

LABORATORY RESULTS

The table provides each of the materials, sample identification number, description/ and corresponding laboratory results.

Asbestos

Sample No.

Suspect Asbestos Material

Asbestos Content Percent by Weight

0312.01 Sheetrock-Mud/Tape - White

House - Office

<1%

0.25 Chrysotile

0312.02 Sheetrock-Mud/Tape - White

House - Kitchen

<1%

0.25 Chrysotile

0312.03 Sheetrock-Mud/Tape - White

House - Restroom

<1%

0.25 Chrysotile

0312.04 Texture atop Sheetrock-Mud/Tape - White

House - Office

<1%

0.25 Chrysotile

0312.05 Texture atop Sheetrock-Mud/Tape-White

House - Garage

<1%

0.25 Chrysotile

0312.06 Texture atop Sheetrock-Mud/Tape - White

House - Kitchen

<1%

0.25 Chrysotile

2714 Dairy Rd (house and barn) pg. 6

Sample

Suspect Asbestos Material

Asbestos Content Percent by Weight

0312.07 Texture atop Sheetrock-Mud/Tape - White

House – Dining Room

<1%

0.25 Chrysotile

0312.08 Texture atop Sheetrock-Mud/Tape - White

House – Restroom

<1%

0.25 Chrysotile

0312.09 Base-cove 4” - Gray

House

None Detected

0312.10 Mastic for Base-cove 4” Gray - Yellow

House

None Detected

0312.11 Floor Tile 12x12 - Gray

House - Office

None Detected

0312.12 Mastic for Floor Tile 12x12 Gray - White

House - Office

None Detected

0312.13 Floor Tile 12x12 - Gray

House - Garage

None Detected

0312.14 Mastic for Floor Tile 12x12 Gray - White

House - Garage

None Detected

0312.15 Insulation – Pink

House Attic

None Detected

0312.16 Shingle Layer 1 – Black

House Roof -

None Detected

0312.17 Shingle Layer 2 – Black

House Roof -

None Detected

0312.18 Felt Layer 3 – Black

House Roof -

None Detected

0312.19 Concrete – Gray

Driveway

None Detected

0312.20 Concrete – Gray

Barn Foundation

None Detected

0312.21 Concrete – Gray

Barn Foundation

None Detected

0312.22 Concrete – Gray

Barn Foundation

None Detected

0312.23 Concrete – Gray

Pesticide – Entry

None Detected

Paint Chip Results

Sample

Suspect Lead Material Specific Location

Lead % by weight

0312.L1 Paint – 1x1 – Sheetrock – White House Interior Walls

<0.01%

2714 Dairy Rd (house and barn) pg. 7

Sample No.

Suspect Lead Material Specific Location

Lead % by weight

0312.L2 Paint – 1x1 – Wood – Tan House Exterior Support

0.04%

0312.L3 Paint – 1x1 – Wood – Tan House Exterior Window

0.01%

0312.L4 Paint – 1x1 – Wood – White House Interior Walls

<0.01%

0312.L5 Paint – 1x1 – Wood – White Exterior Wall

4.82%

0312.L6 Paint – 1x1 – Wood – White Exterior Wall

3.90%

0312.L7 Paint – 1x1 – Wood – White Exterior Facia

5.18%

RECOMMENDATIONS

Asbestos

Licensed Abatement Contractors: The removal of regulated asbestos-containing material must be performed by a state-certified asbestos abatement contractor. General contractors or unlicensed personnel cannot perform this work.

Must follow Cal/OSHA regulations (CCR Title 8 Section 1529), which require containment (sealed barriers, negative air), "wet methods" to control dust, and specific disposal protocols.Notification to the nearest Cal/OSHA office at least 24 hours before starting the project.

Lead Worker Safety (Cal/OSHA §1532.1): If lead is present, employers must perform exposure assessments and provide a written Pre-Job Notification to the nearest Cal/OSHA office at least 24 hours before starting the project.

If suspect lead painted or asbestos materials are discovered during future renovation or demolition operations, cease all work activities which could impact the discovered suspect materials, until confirmation sampling can be conducted.

EXCLUSIONS AND REPORT LIMITATIONS

The information contained in this report is limited to those areas and suspect materials found to be visually accessible through reasonable means.

2714 Dairy Rd (house and barn) pg. 8

Thank you for using Stockton Environmental Inc. please feel free to contact me with any questions regarding this report at (209) 451.3017.

Sincerely, Randolph L Brooke Randolph L. Brooke Vice President

Appendix A dmcal_000 Rectangle dmcal_000 Rectangle dmcal_000 Line dmcal_000 Line dmcal_000 Line randy Image randy Text Box 319 E. Banbury Drive - Stockton, CA 95207 7273 Murray Drive - Stockton, CA 95210 stocktonenvironmental@gmail.com sei Text Box

CONDUCTED AT:

2714 Dairy Rd.

Vernalis, CA 95385

“House and Barn – Demolition Inspection”

PREPARED FOR:

TRCH O.R,.

22350 W Warren Ave Detroit, MI 48239 sei Text Box Report No. 041.26 03/22/2026 sei

SAMPLE LOCATION DIAGRAM

Appendix B

Munoz

ASBESTOS

MicroTest Laboratories Inc. NVLAP Code: 200999-0

3110 Gold Canal Dr. Ste. A. Rancho Cordova, CA 95670

PH 916.567.9808 | FX 916.404.0302

www.microtestlabsinc.com | service@microtestlabsinc.com

Project ID

MT012686134

Date Received: Friday, March 13, 2026

Date Analyzed: Friday, March 13, 2026

Date Reported: Monday, March 16, 2026

Analyst: Andres De Ferrari Authorized Signatory:

Kelly Favero - Lab Manager

Documents #MT-PLM-A 2.2 Proprietary to MicroTest Laboratories, Inc

Authorized by Kelly Favero 1 of 4 Revision Date: 09/11/2025

CLIENT INFORMATION SAMPLE JOB SITE INFORMATION

Company Stockton Environmental Inc. Date Thursday, March 12, 2026 Sampler GBM Name Time Project Address 319 E. Banbury Drive

MicroTest Site House and Barns

Stockton, CA 95207 Address 2714 Dairy Road

Phone (209) 451 - 3017 Laboratories

Vernalis, CA 95385

Email stocktonenvironmental@gmail.com Job # 041.26 Test Report

POLARIZED LIGHT MICROSCOPY (PLM)

EPA METHOD 600 / R-93 / 116 & EPA – 40 CFR Appendix E to Subpart E of Part 763

Client Laboratory Client Laboratory Non Fibrous / Asbestiform

Sample ID Sample ID Description Description Fibrous Materials Minerals %

1 86134-1A Sheetrock | Mud/Tape | White |

Office Cream Joint Compound

Non-Fibrous

Homogenous

99+% Binder <1% Chrysotile

1 86134-1B Sheetrock | Mud/Tape | White |

Office White Sheetrock

Fibrous

Heterogenous

10% Cellulose

90% Binder

2 86134-2A Sheetrock | Mud/Tape | White |

Kitchen Cream Joint Compound

Non-Fibrous

2 86134-2B Sheetrock | Mud/Tape | White |

White Sheetrock

Fibrous

Heterogenous

10% Cellulose

3 86134-3A Sheetrock | Mud/Tape | White |

Restroom Cream Joint Compound

Non-Fibrous

3 86134-3B Sheetrock | Mud/Tape | White |

White Sheetrock

Fibrous

Heterogenous

10% Cellulose

4 86134-4 Texture | A Top SH | White |

Cream Texture

Non-Fibrous

5 86134-5 Texture | A Top SH | White |

Garage Cream Texture

Non-Fibrous

PH 916.567.9808 | FX 916.404.0302

Documents #MT-PLM-A 2.2 Proprietary to MicroTest Laboratories, Inc

Authorized by Kelly Favero 2 of 4 Revision Date: 09/11/2025

6 86134-6 Texture | A Top SH | White |

Kitchen Cream Texture

Non-Fibrous

7 86134-7 Texture | A Top SH | White |

Dining Cream Texture

Non-Fibrous

8 86134-8 Texture | A Top SH | White |

Cream Texture

Non-Fibrous

9 86134-9 Base Cove | 4" | Grey Gray Cove Base

Non-Fibrous

100% Binder None Detected

10 86134-10 Mastic | 4" | Yellow Yellow Mastic

11 86134-11 Floor Tile | 12x12 | Grey | Office Gray Floor Tile

Heterogenous

12 86134-12 Mastic | For #11 | White | Office White Mastic

13 86134-13 Floor Tile | 12x12 | Grey | Garage Gray Floor Tile

14 86134-14 Mastic | for #13 | Yellow | Garage Yellow Mastic

15 86134-15 Insulation | In Attic | Pink | Attic Brown Insulation

Fibrous

100% Fiberglass None Detected

16 86134-16 Roof Shingle | Layer 1 | Black |

Roof Black Roofing Shingle

Fibrous

Heterogenous

10% Fiberglass

17 86134-17 Roof Shingle | Layer 2 | Black |

Roof Black Roofing Shingle

Fibrous

Heterogenous

10% Fiberglass

PH 916.567.9808 | FX 916.404.0302

Documents #MT-PLM-A 2.2 Proprietary to MicroTest Laboratories, Inc

Authorized by Kelly Favero 3 of 4 Revision Date: 09/11/2025

18 86134-18 Felt Paper | Layer 3 | Black | Roof Black Felt

Fibrous

Heterogenous

70% Cellulose

30% Binder

19 86134-19 Concrete | Driveway | Grey | Main

House Gray Concrete

Non-Fibrous

20 86134-20 Concrete | Foundation | Grey |

Barn - Pesticide Gray Concrete

Non-Fibrous

21 86134-21 Concrete | Foundation | Grey |

Barn - 2 Door Gray Concrete

Non-Fibrous

22 86134-22 Concrete | Foundation | Grey |

Barn - Main Gray Concrete

Non-Fibrous

23 86134-23 Concrete | Entry Lip | Grey | Barn

- Pesticide Gray Concrete

Non-Fibrous

PH 916.567.9808 | FX 916.404.0302

Authorized Signatory:

Authorized by Kelly Favero 4 of 4 Revision Date: 09/11/2025

Name Time Project Address 319 E. Banbury Drive

MicroTest Site House and Barns

Stockton, CA 95207 Address 2714 Dairy Road

Phone (209) 451 - 3017 Laboratories

Vernalis, CA 95385

Notes and Definitions

This document serves as the final report. The results apply only to the sample as received. Due to the inherent limitations of Polarized Light Microscopy (PLM) and the complexity of certain sample matrices, some materials classified as "None Detected" (ND) for asbestos (e.g., floor tiles or similar materials) may require further analysis. MicroTest Laboratories recommends additional testing using PLM and/or Transmission Electron Microscopy (TEM) with gravimetric reduction preparation.

Soil, rock and Vermiculite matrices present analytical challenges. MicroTest recommends homogenization by milling before PLM analysis. The thermal breakdown of asbestos fibers can change their properties, causing them to exhibit different mineral characteristics. Even if altered asbestos isn't counted by the method used, OSHA and various state regulations still recognize it as asbestos. PLM analysis will determine the presence of non-altered asbestos, but fire-altered, former asbestos fibers will be reported as an “Altered” Asbestiform result. Materials commonly seen with fire-altered minerals include, but are not limited to, cementitious sidings, tiles, textures, joint compounds, and fibrous backings. Due to the potential for incomplete or partial decomposition, additional analysis by TEM is advisable.

The reporting limit for calibrated visual area estimation quantitation procedures is 1%. The reporting limits for 400-point count and 1000-point count quantitation procedures are 0.25% and 0.1%, respectively. Samples are considered acceptable unless otherwise noted. Each layer of a sample is analyzed separately unless it consists of multiple manufactured layers (e.g., linoleum, drywall) or if otherwise specified by the client.

Samples received from multiple homogeneous areas and placed in a single bag were analyzed using MicroTest’s MT Sub-sampling Standard Operating Procedures.

This method ensures unambiguous and reliable analysis despite the combined nature of the samples received.

All samples will be retained for a minimum of 30 days before disposal. Bench sheets detailing sampling methodologies can be provided upon request. This report must not be used by the client to imply product endorsement by NVLAP or any agency of the U.S. Government. This report may only be reproduced in its entirety with the written approval of MicroTest Laboratories, Inc.

Estimated Positive Error Ranges <1% - 2% : +/- 1% 3 - 20% : +/- 6% 21 - 50% : +/- 17% 51+% : +/- 23%

Total Samples Received: 23 Total layers analyzed: 26

PH 916.567.9808 | FX 916.404.0302

Date Analyzed: Wednesday, March 18, 2026

Date Reported: Thursday, March 19, 2026

Analyst: Rosey Nagra Authorized Signatory:

Authorized by Kelly Favero 1 of 2 Revision Date: 09/11/2025

Name Time Project Address 319 E. Banbury Drive

MicroTest Site House and Barns

Stockton, CA 95207 Address 2714 Dairy Road Phone (209) 451 - 3017

Laboratories Vernalis, CA 95385

Test Report

POLARIZED LIGHT MICROSCOPY (PLM) - 400 Point Count

EPA METHOD 600 / R-93 / 116 & EPA – 40 CFR Appendix E to Subpart E of Part 763

Client Laboratory Client Laboratory Non Fibrous / Asbestiform

Sample ID Sample ID Description Description Fibrous Materials Minerals %

1 86134-1A Sheetrock | Mud/Tape | White | Office

Cream Joint Compound Non-Fibrous

99+% Binder 0.25% Chrysotile

2 86134-2A Sheetrock | Mud/Tape | White |

Cream Joint Compound Non-Fibrous

3 86134-3A Sheetrock | Mud/Tape | White |

Cream Joint Compound Non-Fibrous

4 86134-4 Texture | A Top SH | White |

Cream Texture Non-Fibrous

5 86134-5 Texture | A Top SH | White | Garage

Cream Texture Non-Fibrous

6 86134-6 Texture | A Top SH | White |

Cream Texture Non-Fibrous

7 86134-7 Texture | A Top SH | White | Dining

Cream Texture Non-Fibrous

8 86134-8 Texture | A Top SH | White |

Cream Texture Non-Fibrous

PH 916.567.9808 | FX 916.404.0302

Authorized Signatory:

Authorized by Kelly Favero 2 of 2 Revision Date: 09/11/2025

Name Time Project Address 319 E. Banbury Drive

MicroTest Site House and Barns

Stockton, CA 95207 Address 2714 Dairy Road Phone (209) 451 - 3017

Laboratories Vernalis, CA 95385

This document serves as the final report. The results apply only to the sample as received. Due to the inherent limitations of Polarized Light Microscopy (PLM) and the complexity of certain sample matrices, some materials classified as "None Detected" (ND) for asbestos (e.g., floor tiles or similar materials) may require further analysis. MicroTest Laboratories recommends additional testing using PLM and/or Transmission Electron Microscopy (TEM) with gravimetric reduction preparation.

Soil, rock and Vermiculite matrices present analytical challenges. MicroTest recommends homogenization by milling before PLM analysis. The thermal breakdown of asbestos fibers can change their properties, causing them to exhibit different mineral characteristics. Even if altered asbestos isn't counted by the method used, OSHA and various state regulations still recognize it as asbestos. PLM analysis will determine the presence of non-altered asbestos, but fire-altered, former asbestos fibers will be reported as an “Altered” Asbestiform result. Materials commonly seen with fire-altered minerals include, but are not limited to, cementitious sidings, tiles, textures, joint compounds, and fibrous backings. Due to the potential for incomplete or partial decomposition, additional analysis by TEM is advisable.

The reporting limit for calibrated visual area estimation quantitation procedures is 1%. The reporting limits for 400-point count and 1000-point count quantitation procedures are 0.25% and 0.1%, respectively. Samples are considered acceptable unless otherwise noted. Each layer of a sample is analyzed separately unless it consists of multiple manufactured layers (e.g., linoleum, drywall) or if otherwise specified by the client.

Samples received from multiple homogeneous areas and placed in a single bag were analyzed using MicroTest’s MT Sub-sampling Standard Operating Procedures.

This method ensures unambiguous and reliable analysis despite the combined nature of the samples received.

All samples will be retained for a minimum of 30 days before disposal. Bench sheets detailing sampling methodologies can be provided upon request. This report must not be used by the client to imply product endorsement by NVLAP or any agency of the U.S. Government. This report may only be reproduced in its entirety with the written approval of MicroTest Laboratories, Inc.

Estimated Positive Error Ranges <1% - 2% : +/- 1% 3 - 20% : +/- 6% 21 - 50% : +/- 17% 51+% : +/- 23%

Total Samples Received: 8 Total layers analyzed: 26

Outlook

Re: 86134 2714 Dairy Road PLM Binder 031626

From dwayne mcallister <dwayne@stkenv.com> Date Wed 3/18/2026 9:20 AM To stocktonenvironmental@gmail.com <stocktonenvironmental@gmail.com>; frank@stkenv.com

<frank@stkenv.com>; MicroTest Labs | Customer Service <service@microtestlabsinc.com>

Good morning, Please reanalyze samples: 1, 2, 3, 4, 5, 6, 7 & 8 via 400 pt count on a 24 hr ta

Thank you

Sincerely, Dwayne G. McAllister

Stockton Environmental, Inc.

209.451.3017 www.stocktonenvironmentalinc.com

On Monday, March 16, 2026 at 08:50:55 AM PDT, <service@microtestlabsinc.com> wrote:

Good Morning, Please see the attached binder for the site listed above.

Thank you, Ellee Sager

We'd love to hear from you - Take our survey!

MicroTest Laboratories, Inc.

3110 Gold Canal Drive, Suite A Rancho Cordova, CA 95670 Ph: 916.567.9808 Fx: 916.404.0302 www.microtestlabsinc.com

This email may contain privileged and confidential information and is solely for the use of the sender's intended recipient(s). If you are not the intended recipient of this communication, you are hereby notified that any unauthorized review, use, dissemination, distribution, downloading, or copying of this communication is strictly prohibited. If you received this email in error, please notify the sender by reply email and kindly delete all copies and attachments. Thank you.

http://www.stocktonenvironmentalinc.com/ https://microtestlabsinc.com/ https://www.surveymonkey.com/r/MicroTestlabsinc

Appendix B

Munoz

LEAD

CLIENT INFORMATION JOB SITE INFORMATION

Date Sampler

Time Project

Site

Address

Job #

PO #

0.04 % Wt

383.1 PPM

0.01 % Wt

138.7 PPM

<RL % Wt

<RL PPM

4.82 % Wt

48154 PPM

3.90 % Wt

39031 PPM

5.18 % Wt

51818 PPM

Date Received:

Date Analyzed:

Date Reported:

Analyst:

Not Received

Comments

***for office use only***

Company Stockton Environmental Inc

SAMPLE

MicroTest Laboratories, Inc. | AIHA ELPAT #160934 Project ID

3110 Gold Canal Dr, Ste. A, Rancho Cordova, CA 95670

PH 916.567.9808 | FX 916.404.0302

86118 www.microtestlabsinc.com | service@microtestlabsinc.com

Thursday, March 12, 2026 GBM

Stockton, CA 95207

Address 319 E. Banbury Drive

Name

Analytical Report

Lead in Paint/Bulk Analysis by Flame AA - EPA METHOD 7420/7000B

House and Barns

2714 Dairy Road

Vernalis, CA 95385

41.26

Client Laboratory Reporting

Phone 209.451.3017 MicroTest Laboratories

Client

Email stocktonenvironmental@gmail.com

1 86118-X 1x1 - Sheetrock | White | Interior Walls Paint/Bulk

Sample ID Sample ID Sample Description Matrix Results Limits (RL)

DNA

2 86118-1 1x1 - Wood | Tan | Exterior Support Paint/Bulk 0.01 %Wt

100 PPM

3 86118-2 1x1 - Wood | Tan | Exterior Window Paint/Bulk 0.01 %Wt

100 PPM

4 86118-3 1x1 - Wood | White | Exterior Wall Paint/Bulk 0.01 %Wt

6 86118-5 1x1 - Wood | White | Exterior Wall Paint/Bulk 0.1 %Wt

10000 PPM

5 86118-4 1x1 - Wood | White | Exterior Wall Paint/Bulk 1 %Wt

10000 PPM

7 86118-6 1x1 - Wood | White | Exterior Fascia Paint/Bulk 1 %Wt

This report applies to the standards and procedures indicated to the specific samples analyzed. Samples have NOT been corrected for blank values. EPA 3050B Mod.

Erich Bowman

Friday, March 13, 2026

Friday, March 13, 2026

Monday, March 16, 2026

Kelly Favero - Lab Manager

Authorized Signatory:

1000 PPM

100 PPM

Document # MT-FAA 2.0

Authorized by Kelly Favero 1 of 1

Proprietary to MicroTest Laboratories, Inc

Issue Date: 031324

CLIENT INFORMATION JOB SITE INFORMATION

Date Sampler

Time Project

Site

Address

Job #

PO #

<RL % Wt

<RL PPM

Date Received:

Date Analyzed:

Date Reported:

Analyst:

This report applies to the standards and procedures indicated to the specific samples analyzed. Samples have NOT been corrected for blank values. EPA 3050B Mod.

Lexie Cepeda

Tuesday, March 17, 2026

Tuesday, March 17, 2026

Wednesday, March 18, 2026

Kelly Favero - Lab Manager

Authorized Signatory:

1 86351-1 Paint Chip | 1x1 Sheetrock | White | Interior Walls Paint/Bulk 0.01 %Wt

Sample ID Sample ID Sample Description Matrix Results Limits (RL)

100 PPM

Analytical Report

Lead in Paint/Bulk Analysis by Flame AA - EPA METHOD 7420/7000B

House and Barns

2714 Dairy Road

Vernalis, CA 95385

41.26

Client Laboratory Reporting

Phone 209.451.3017 MicroTest Laboratories

Client

Email stocktonenvironmental@gmail.com

Comments

***for office use only***

Company Stockton Environmental Inc

SAMPLE

MicroTest Laboratories, Inc. | AIHA ELPAT #160934 Project ID

3110 Gold Canal Dr, Ste. A, Rancho Cordova, CA 95670

PH 916.567.9808 | FX 916.404.0302

86351 www.microtestlabsinc.com | service@microtestlabsinc.com

Thursday, March 12, 2026 GBM

Stockton, CA 95207

Address 319 E. Banbury Drive

Name

Document # MT-FAA 2.0

Authorized by Kelly Favero 1 of 1

Proprietary to MicroTest Laboratories, Inc

Issue Date: 031324

Appendix C dwayn Image

Frank Image

Frank Image

Frank gabri gabri Image gabri Image gabri Image dwayn Image

Frank Image

Frank Image

Frank Image

Frank