Attachment_14_Bldg_138_0003.pdf

Asbestos Survey for Building 138

Southwestern Indian Polytechnic Institute 9169 Coors Blvd NW, Albuquerque, NM 87120

Prepared by:

ARS Aleut Construction 4100 Lafayette Center Dr., Suite 115, Chantilly, VA 20151

(614) 937-6664

February 2021

Comprehensive Asbestos Survey Southwestern Indian Polytechnic Institute (SIPI)

Albuquerque, NM i ARS Aleut Construction, LLC

Asbestos Survey, For Building 138

9169 Coors Blvd NW, Albuquerque, NM 87120

Contract No. 140A1618D0006/140A1620F0161 Prepared for:

Southwestern Indian Polytechnic Institute 9169 Coors Blvd NW, Albuquerque, NM 87120

Prepared by:

ARS Aleut Construction, LLC.

4100 Lafayette Center Dr., Suite 115, Chantilly, VA 20151

(614) 937-6664

X Jose J. Sosa, P.E., CIH CIH No. 5429

X Robert Provost, IHT/RSO

February 2021 ii

TABLE OF CONTENTS

1.0 EXECUTIVE SUMMARY

1.1 Asbestos-Containing Material Summary

2.0 BUILDING INFORMATION

3.0 LIMITATIONS OF THE SURVEY

4.0 ASBESTOS SURVEY

4.1 ACM Survey Findings: Building 138

4.2 Asbestos Survey Protocol

4.3 Regulatory Review

5.0 CONCLUSIONS

6.0 RECOMMENDATIONS

7.0 TABLES AND RESULTS

APPENDICES

Appendix A: Chain of Custody Form & Laboratory Analytical Report Appendix B: Positive Sample Photos Appendix C: Floor Plans Appendix D: Certifications iii

LIST OF ACRONYMS

AAC ARS ALEUT CONSTRUCTION

A/C AIR CONDITIONER

ACBM(s) ASBESTOS-CONTAINING BUILDING MATERIAL (S) ACM(s) ASBESTOS-CONTAINING MATERIAL (S)

AMO AMOSITE

BLDG BUILDING

BUR BUILT-UP ROOF

CBS CONCRETE BLOCK SYSTEM

COMP COMPOUND

CRY CHRYSOTILE

CT CEILING TILE (S)

DECO DECORATIVE

DIR DIRECTIONAL

D/I DROP-IN

D/W DRYWALL

EXT EXTERIOR

F/P FISSURES/PINHOLES

HA HOMOGENEOUS AREA

HVAC HEATING, VENTILATING AND AIR CONDITIONING

INT INTERIOR

JT JOINT

LF LINEAR FEET

LT LIGHT

L/F LONG FISSURES

L/W LENGTHWISE

N/A NOT APPLICABLE

NAD NO ASBESTOS DETECTED

NA NOT ANALYZED

NO NUMBER

NA/PS NOT ANALYZED / POSITIVE STOP

O&M OPERATION AND MAINTENANCE

PLM POLARIZED LIGHT MICROSCOPY

QA/QC QUALITY ASSURANCE/QUALITY CONTROL

RACM(s) REGULATED ASBESTOS-CONTAINING MATERIAL (S)

RVF ROLLED VINYL FLOORING

SF SQUARE FEET

S/F STOREFRONT

TSI THERMAL SYSTEM INSULATION

VBB VINYL BASEBOARD

VFT VINYL FLOOR TILE

VTR VENT-THROUGH-ROOF

1.0 EXECUTIVE SUMMARY

ARS Aleut Construction, LLC (AAC) was retained by the Southwestern Indian Polytechnic Institute (SIPI) to perform a comprehensive Asbestos Containing Materials (ACM) Survey, of structures located within the boundaries of the Institute. The Institute is located at 9169 Coors Blvd NW, Albuquerque, NM 87120. This report contains the findings and results of the inspection of Building 138.

1.1 Asbestos-Containing Material Summary

The scope of the survey included to visually inspect and identify all visible building components and finishes considered as suspect asbestos containing materials. The survey was performed according to current Environmental Protection Agency’s (EPA) and the State of New Mexico’s regulations. Federal and state regulations outline the procedures for the identification and sampling guidelines of suspect asbestos containing materials.

Four (4) homogeneous areas (HA’s) of suspect ACM were identified during the visual inspection of Building 138. Analytical results from the samples collected in Building 138 were below the regulatory threshold of 1%.

Table 1 in Section 7 of this report contains the inventory and the number of samples collected during the inspection and Table 2 is the PLM results of the QC’s taken throughout the building. Appendix A contains the chain of custody, sample inventory forms and the analytical report from the laboratory. Appendix B contains the pictures of building materials determined to contain asbestos above the regulatory threshold.

Appendix C contains floor plans showing the location of the samples collected. Appendix D is the surveyor’s certifications.

2.0 BUILDING INFORMATION

Building Name Guard Bldg.

Year Built 1990

Building Number 138

Area of Survey 207 SF

Building Type Business

# of Floors 1

Purpose of ACM Survey Renovation

Building Survey Date 11/12/2020

3.0 LIMITATIONS OF THE SURVEY

ARS Aleut Construction (AAC) performed a comprehensive Asbestos Containing Material (ACM) Survey. The following limitations apply to the scope of our services:

• Survey performed was non-destructive, the inspectors made every attempt to identify accessible suspect materials, suspect materials concealed behind chases or other parts of the building requiring removal were not sampled.

• The quantities provided are visual estimations and should not be utilized as scope quantities for abatement.

• Roofs under warranty were not sampled to avoid nullifying or affecting the warranty.

• The inspectors made up to three attempts to access locked spaces. Rooms or areas with a building are noted if access was not obtained.

4.0 ASBESTOS SURVEY

The ACM inspection was performed in accordance with the following regulations for asbestos.

National Emission Standards for Hazardous Air Pollutants (NESHAP), U.S.

Environmental Protection Agency’s (USEPA) requirements for implementation of the Asbestos Hazard Emergency Response Act (AHERA) and the Asbestos School Hazard Abatement Reauthorization Act (ASHARA).

Mr. Robert Provost, Kimberley Marshall, Robert A. Sanders, and Andrew Strong carried out the asbestos survey on 12 November 2020. The work was performed under the supervision of Jose J. Sosa, PE, CIH, LAC. Appropriate certification documents are contained in Appendix D of this report.

4.1 ACM Survey Findings: Building 138

The AAC asbestos inspectors performed a visual inspection of all accessible spaces in the building including the exterior to identify those building materials which the EPA has classified as suspect materials that may contain asbestos fibers in their composition matrix. Each material is given a homogenous area designation, a homogeneous area is defined as an area of surfacing, thermal system insulation (TSI), or a miscellaneous building material that is uniform in color or texture and applied on the same date. Four (4) homogeneous areas (HA’s) of suspect ACM were identified during the visual inspection of Building 138. None of the building materials tested contained asbestos in excess of the regulatory threshold of 1%.

4.2 Asbestos Survey Protocol

Samples were given a unique numeric identification (i.e. 138-1a, 138-1B, etc.). The first three digits corresponding to the building number followed by a number starting with “1” increasing sequentially with the last number representing the total number of homogenous areas identified within the structure. The alphabetical listing indicates the samples collected within a homogeneous sampling area, starting with letter “A” and continuing in alphabetical order. Each sample location was identified on the sample location drawings attached within this document.

Samples of building materials such as vinyl floor tile and associated mastic are considered a multi-layer sample. When analyzed results are reported for each individual layer, thus a sample ID can appear twice showing the multi-layered sample. The laboratory uses L1 and L2 to report and differentiate each layer.

The technique used for sampling the suspect materials was designed to minimize possible fiber release and in turn possible contamination of surround areas. All representative “suspect” materials sampled, were collected in accordance with the EPA’s AHERA and “Guidance for controlling Asbestos Containing Material in Buildings” (EPA 560 / 6-85-024, June 1985).

The sampling procedures of surfacing suspect materials according to AHERA, are known as the 3-5-7 Rule. It is based on square footage of the suspect material present. AHERA recommends up to 1,000 square feet area of a suspect material that a minimum of three samples be collected, quantities between 1,001-5,000 square feet a minimum of five samples is recommended to be collected, and for material greater than 5,000 square feet, a minimum of seven samples are required to be collected. For miscellaneous suspected materials, the AHERA requirements state to collect samples but does not include a specified amount. For miscellaneous suspected samples, the minimum required number of samples is two. The inspector randomly selects rooms in which samples are to be collected, therefore collecting samples from each room is not recommended not required by federal guidelines.

Suspect materials were wet with an amended soapy water mixture. AAC personnel utilized PPE as deemed appropriate for each sampling event. AAC personnel utilized wet methods while collecting bulk samples.

A representative sample of the material was collected and placed in a labeled airtight bag.

A chain of custody form was completed for all bulk samples collected and shipped to AmeriSci Richmond, Inc. for analysis using Polarized Light Microscopy (PLM). AmeriSci Richmond, Inc. Utilizes dispersion staining techniques according to US EPA method 600 / M4-82-020 incorporating visual estimates of identified material percentages. Once one sample comes back as positive then the entire HA is considered positive, and analysis of additional samples is not required.

During the sampling activities, each suspect ACM was touched by the inspector to determine its friability and observed to determine the physical condition of the material. A friable material is defined as a material that can be crumbled or reduced to powder by hand pressure. Friability of a material directly relates to a potential of the ACM to release airborne fibers. The more friable the ACM the more likely asbestos fibers will be released.

The inspector assessed the suspect ACM according to their physical conditions.

Joint compound associated with gypsum wallboard system will be evaluated to determine whether the material should be classified as “joint compound” or “Skim coat” per EPA’s NESHAP clarification letter published in the Federal Register on January 5th, 1994.

The AAC inspectors split the bulk samples every 20th sample collected. The QA/QC samples were sent to the laboratory under a separate chain of custody from the original building materials sampled. The samples were analyzed by a different PLM analyst in order to compare the original sample results to the QC results. Table 2 contains the QC samples for the specified building. The PLM results for all QC samples analyzed can be found in the attached Quality Control (QC) Sample Results report.

4.3 Regulatory Review

NESHAP (40 CFR Part 61, Subpart M) regulates asbestos fiber emissions and asbestos waste disposal practices. NESHAP requires the identification and classification of existing ACM according to friability prior to demolition or renovation activity.

Under NESHAP, asbestos-containing building materials are classified as:

1. Friable ACM, or

2. Category I Non-Friable ACM, or

3. Category II Non-Friable ACM.

Friable materials are those that, when dry, may be crumbled, pulverized, or reduced to powder by hand pressure.

Category I Non-Friable ACM includes packings, gaskets, resilient floor coverings, mastic or asphalt roofing products containing more than 1% asbestos.

Category II Non-Friable ACM are any materials other than Category I Non-Friable ACM that contain more than 1% Asbestos.

Under NESHAP, Regulated Asbestos-Containing Materials (RACM) are classified as:

1. Friable ACM,

2. Category I Non-Friable ACM that is in poor condition and/or has become friable,

3. Category I Non-Friable ACM that will or has been subjected to sanding, grinding, cutting, or abrading

4. Category II Non-Friable ACM that has a high probability of becoming or has become crumbled, pulverized or reduced to powder by the forces expected to act upon the material in the course of renovation or demolition operations.

According to NESHAP, RACM must be removed prior to renovation or demolition activities that will disturb the materials. Removal of the ACM or RACM must be conducted by a State of New Mexico licenses asbestos abatement contractor, in compliance with

New Mexico regulations. In addition, third party air monitoring should be performed during and following the abatement.

The Occupational Safety and Health Administration (OSHA) Asbestos Standard for Construction (29 CFR 1926.1101) regulates employee workplace exposure to asbestos.

The OSHA standard has two Permissible Exposure Limits (PEL) that require employee expose to airborne asbestos fibers be maintained below 0.1 asbestos fibers per cubic centimeter of air (0.1 f/cc) for an 8-hour Time-Weighted Average (8-Hr. TWA) and 1.0 f/cc for a 30-minute TWA (Excursion Limit).

The OSHA standard classifies construction and maintenance activities that could disturb ACM and specifies work practices and precautions that employers must follow when engaged in each class of regulated work. The OSHA classes are described below.

• Class I Asbestos Work means activities involving the removal of TSI and Surfacing ACM and PACM.

• Class II Asbestos Work means activities involving the removal of ACM which is not thermal system insulation or surfacing material. This includes, but is not limited to, the removal of asbestos-containing wallboard, floor tile and sheeting, roofing and siding shingles, and construction mastics.

• Class III Asbestos Work means repair and maintenance operations, where “ACM”, including TSI and surfacing ACM and PACM, is likely to be disturbed.

• Class IV Asbestos Work means maintenance and custodial activities during which employees contact but do not disturb ACM and PACM and activities to clean up dust, waste and debris resulting from Class I, II, and III activities

The Air Quality Bureau (ABQ) is the agency in New Mexico with the oversight responsibility of the asbestos program. The AQB follows the National Emission Standards for Hazardous Air Pollutants (NESHAP). The New Mexico State Legislature adopted the NESHAP regulations (20 NMAC 2.78) for asbestos control in New Mexico statewide.

Albuquerque- Bernalillo County has additional regulation 20.11.20.22 NMAC.

20.11.20.22 Demolition and Renovation Activities; Fugitive Dust Control Construction Permit and Asbestos Notification Requirements. The Demolition and Renovation must also comply with federal standards incorporated in 20.11.64 NMAC, Emission Standards for Hazardous Air Pollutants for Stationary Sources.

5.0 CONCLUSIONS

Based on the analytical results of the samples collected from Building 138, asbestos fibers in the building materials were reported to be below the regulatory threshold of 1%.

Building components and/or finishes in building 138 can be treated as Non-Asbestos Containing Materials.

The inspectors did not collect samples from every elbow in the buildings on campus. Two of the pipe elbow insulations sampled in Building 113, Four Winds Lodge, and one sample of the elbow insulation in Building 104, Library, collected above the ceilings were found to contain asbestos above the regulatory threshold of 1%. However, samples of the elbow insulations collected in the mechanical rooms of all buildings sampled did not contain asbestos fibers in their composition matrix. The mechanical rooms throughout the campus may have undergone renovations after initial construction. Therefore, any buildings with an initial date on construction, in 1971, should be assumed to contain asbestos fibers within the elbow insulations.

6.0 RECOMMENDATIONS

Construction and demolition (C&D) debris generated during renovations or demolition of building 138 should be treated as C&D waste. Disposal of the C&D waste should be at a C&D landfill.

Any proposed renovations and/or demolition that may disturb the elbow insulation not replaced following initial construction of 1971 in any building throughout the campus should be sampled and analyzed for asbestos or treated as asbestos containing materials. If the elbows are to be removed or disturbed during renovations or demolition, they should be abated following the state and local guidelines.

7.0 TABLES AND RESULTS

Table 1 in this section contains the sampling inventory of all identified suspect materials within the building.

Table 2 is the PLM results of the QC’s taken throughout the building.

PLM Lab Results SIPI Super Project

Project Number: P20010-E1503

Sample ID Analyst Description of Material Sample Material / Room

Number

HA

Asbestos Present?

(Y%/N)

138- 1A Gray/Beige, Heterogeneous, Non-

Fibrous, Bulk Material Exterior; Stucco; Exterior 1 NAD

138- 1B Gray/Beige, Heterogeneous, Non-

Fibrous, Bulk Material Exterior; Stucco; Exterior 1 NAD

138- 1C Gray/Beige, Heterogeneous, Non-

Fibrous, Bulk Material Exterior; Stucco; Exterior 1 NAD

138- 2A White, Heterogeneous, Non-

Fibrous, Bulk Material Drywall; Interior 2 NAD

138- 2B White/Beige, Heterogeneous, Non-

Fibrous, Bulk Material Drywall; Interior 2 NAD

138- 2C White/Beige, Heterogeneous, Non-

Fibrous, Bulk Material Drywall; Interior 2 NAD

138- 3A White, Heterogeneous, Non-

Fibrous, Bulk Material Orange Peel Ceiling; Interior 3 NAD

138- 3B White, Heterogeneous, Non-

Fibrous, Bulk Material Orange Peel Ceiling; Interior 3 NAD

138- 3C White, Heterogeneous, Non-

Fibrous, Bulk Material Orange Peel Ceiling; Interior 3 NAD

138- 4A Tan, Heterogeneous, Non-Fibrous, Mastic Cove Base; Interior 4 NAD

138- 4B Tan, Heterogeneous, Non-Fibrous, Mastic Cove Base; Interior 4 NAD

NAD = No Asbestos Detected NA/PS = Not Analyzed/Positive Stop NA = Not Analyzed

L1 Denotes Layer 1 of Suspect Material L2 Denotes Layer 2 of Suspect Material

Table 1 - Sampling Inventory of Suspect Materials in Building 138

* Additional Samples Taken on January 19th-21st, 2021

PLM Lab Results SIPI Super Project

Project Number: P20010-E1503

Sample ID Analyst Description of

Material Sample Material / Room

Number

HA

PLM Results (Total % Asbestos Type)

138-1aa Tan, Heterogeneous, Non-Fibrous, Mastic Stucco QC NAD

NAD = No Asbestos Detected NA/PS = Not Analyzed/Positive Stop NA = Not Analyzed

L1 Denotes Layer 1 of Suspect Material

Table 2 - QUALITY CONTROL Analytical Results of Bulk Samples Collected from BUILDING 138

* Additional Samples Taken on January 19th-21st, L2 Denotes Layer 2 of Suspect Material

Albuquerque, NM

Appendix A Chain of Custody Form & Laboratory Analytical Report

November 22, 2020

Dear Jose Sosa:

ARS Aleut Construction, LLC Attn: Jose Sosa 9800 4th Street N, Suite 200 Saint Petersburg, FL 33702

RE: ARS Aleut Construction, LLC Job Number 120111759 P.O. #P20010-E1503 P20010-E1503; SIPI Super Project; 9169 Coors Blvd NW, Albuquerque, NM 87120

AmeriSci Richmond

13635 GENITO ROAD

MIDLOTHIAN, VIRGINIA 23112

TEL: 8047631200 FAX: 8047631800

Enclosed are the results for PLM asbestos analysis of the following ARS Aleut Construction, LLC samples received at AmeriSci on Tuesday, November 17, 2020, for a 5 day turnaround:

138-1A, 138-1B, 138-1C, 138-2A, 138-2B, 138-2C, 138-3A, 138-3B, 138-3C, 138-4A, 138-4B

The 11 samples contained in zip lock bag were shipped to AmeriSci via Fed Ex 8149 1844 0812 B. These samples were prepared and analyzed according to EPA PLM Method (EPA 600/R-93/116 Section 2.2). The required analytical information, analysis results, analyst signature and laboratory identification are contained in the PLM Bulk Asbestos Report. If TEM analysis was requested for selected samples the gravimetric reduction data (by Sec 2.3) and TEM Asbestos % (by Sec 2.5) are included in Table 1 along with a summary of Asbestos % by PLM for all samples analyzed.

This report relates ONLY to the sample analysis expressed as % asbestos. AmeriSci assumes no responsibility for customer supplied data such as “sample type”, "location", or “area sampled”. This report must not be used to claim product endorsement by AmeriSci, NVLAP or any agency of the U. S. Government. The National Institute of Standards and Technology accreditation requirements mandate that this report must not be reproduced, except in full, without the written approval of the laboratory. This report may contain specific data not covered by NVLAP or ELAP accreditations, if so identified in relevant footnotes.

Beverly A. Schrage

Sincerely, Senior Analyst | Authorized Signatory

AmeriSci appreciates this opportunity to serve your organization. Please contact us for any further assistance or with any questions.

Boston - Los Angeles - New York - Richmond

AmeriSci Richmond

13635 GENITO ROAD

MIDLOTHIAN, VIRGINIA 23112

TEL: (804) 763-1200 • FAX: (804) 763-1800

11/17/20 AmeriSci Job # 120111759 11/22/20

1 3 P20010-E1503; SIPI Super Project; 9169 Coors Blvd NW, Albuquerque, NM 87120

PLM Bulk Asbestos Report Date Received Date Examined

RE:

ofPage

P.O. # ARS Aleut Construction, LLC

9800 4th Street N, Suite 200

Saint Petersburg, FL 33702

Attn: Jose Sosa

Asbestos Present Total % AsbestosClient No. / HGA Lab No.

Location:

Analyst Description:

Asbestos Types:

Other Material:

No138-1A 120111759-01 NAD Exterior; Stucco; Exterior1

Gray/Beige, Heterogeneous, Non-Fibrous, Bulk Material

Non-fibrous 100 %

(by CVES) by Beverly A. Schrage on 11/22/20

Location:

Analyst Description:

Asbestos Types:

Other Material:

No138-1B 120111759-02 NAD Exterior; Stucco; Exterior1

Gray/Beige, Heterogeneous, Non-Fibrous, Bulk Material

Non-fibrous 100 %

(by CVES) by Beverly A. Schrage on 11/22/20

Location:

Analyst Description:

Asbestos Types:

Other Material:

No138-1C 120111759-03 NAD Exterior; Stucco; Exterior1

Gray/Beige, Heterogeneous, Non-Fibrous, Bulk Material

Fibrous glass Trace, Non-fibrous 100 %

(by CVES) by Beverly A. Schrage on 11/22/20

Location:

Analyst Description:

Asbestos Types:

Other Material:

No138-2A 120111759-04 NAD Drywall; Interior2

White, Heterogeneous, Non-Fibrous, Bulk Material

Non-fibrous 100 %

(by CVES) by Beverly A. Schrage on 11/22/20

Location:

Analyst Description:

Asbestos Types:

Other Material:

No138-2B 120111759-05 NAD Drywall; Interior2

White/Beige, Heterogeneous, Non-Fibrous, Bulk Material

Cellulose 5 %, Non-fibrous 95 %

(by CVES) by Beverly A. Schrage on 11/22/20

See Reporting notes on last page

AmeriSci Job #: 120111759 Page 2 of 3

P20010-E1503; SIPI Super Project; 9169 Coors Blvd NW, Albuquerque, NM 87120

PLM Bulk Asbestos Report Client Name: ARS Aleut Construction, LLC

Asbestos Present Total % AsbestosClient No. / HGA Lab No.

Location:

Analyst Description:

Asbestos Types:

Other Material:

No138-2C 120111759-06 NAD Drywall; Interior2

White/Beige, Heterogeneous, Non-Fibrous, Bulk Material

Cellulose 5 %, Non-fibrous 95 %

(by CVES) by Beverly A. Schrage on 11/22/20

Location:

Analyst Description:

Asbestos Types:

Other Material:

No138-3A 120111759-07 NAD Orange Peel Ceiling; Interior3

White, Heterogeneous, Non-Fibrous, Bulk Material

Non-fibrous 100 %

(by CVES) by Beverly A. Schrage on 11/22/20

Location:

Analyst Description:

Asbestos Types:

Other Material:

No138-3B 120111759-08 NAD Orange Peel Ceiling; Interior3

White, Heterogeneous, Non-Fibrous, Bulk Material

Non-fibrous 100 %

(by CVES) by Beverly A. Schrage on 11/22/20

Location:

Analyst Description:

Asbestos Types:

Other Material:

No138-3C 120111759-09 NAD Orange Peel Ceiling; Interior3

White, Heterogeneous, Non-Fibrous, Bulk Material

Non-fibrous 100 %

(by CVES) by Beverly A. Schrage on 11/22/20

Location:

Analyst Description:

Asbestos Types:

Other Material:

No138-4A 120111759-10 NAD Cove Base; Interior4

Tan, Heterogeneous, Non-Fibrous, Mastic

Non-fibrous 100 %

(by CVES) by Beverly A. Schrage on 11/22/20

Location:

Analyst Description:

Asbestos Types:

Other Material:

No138-4B 120111759-11 NAD Cove Base; Interior4

Tan, Heterogeneous, Non-Fibrous, Mastic

Non-fibrous 100 %

(by CVES) by Beverly A. Schrage on 11/22/20

See Reporting notes on last page

AmeriSci Job #: 120111759 Page 3 of 3

P20010-E1503; SIPI Super Project; 9169 Coors Blvd NW, Albuquerque, NM 87120

PLM Bulk Asbestos Report Client Name: ARS Aleut Construction, LLC

Reporting Notes:

*NAD = no asbestos detected, Detection Limit <1%, Reporting Limits: CVES = 1%, 400 Pt Ct = 0.25%, 1000 Pt Ct = 0.1%; "Present" or NVA = "No Visible Asbestos" are observations made during a qualitative analysis; NA = not analyzed; NA/PS = not analyzed / positive stop; PLM Bulk Asbestos Analysis using Meiji, Model MT 6130 microscope, Serial #1410301, by EPA 600/R-93/116 per 40 CFR 763 (NVLAP Lab Code 101904-0) and ELAP PLM Analysis Protocol 198.1 for New York friable samples which includes quantitation of any vermiculite observed (198.6 for NOB samples) or EPA 400 pt ct by EPA 600/M4-82-020 (NYSDOH ELAP Lab # 10984); CA ELAP Lab # 2508; Note: PLM is not consistently reliable in detecting asbestos in floor coverings and similar NOB materials. NAD or Trace results by PLM are inconclusive, TEM is currently the only method that can be used to determine if this material can be considered or treated as non-asbestos-containing in New York State (also see EPA Advisory for floor tile, FR 59, 146, 38970, 8/1/94). NIST Accreditation requirements mandate that this report must not be reproduced except in full without the approval of the laboratory. This PLM report relates ONLY to the items tested.

Analyzed by: Beverly A. Schrage Date: 11/22/2020

Reviewed by: Beverly A. Schrage

Albuquerque, NM

Appendix B Positive Sample Photos

Albuquerque, NM

No positive Regulated ACM found in building

Albuquerque, NM

Appendix C Floor Plans

ASBESTOS SURVEY SAMPLE LOCATIONS

BUILDING #138, GUARDHOUSE

SOUTHWESTERN INDIAN POLYTECHNIC INSTITUTION

ALBUQUERQUE, NEW MEXICO

0 2.5 5

SCALE: 1" = 5'

ASBESTOS CONTAINING MATERIAL

SAMPLE LOCATIONS LEGEND

NON-ASBESTOS CONTAINING MATERIAL

POSITIVE SAMPLE

NEGATIVE SAMPLE

ASBESTOS CONTAINING MATERIAL

NON-ASBESTOS CONTAINING MATERIAL

POSITIVE MULTI-LAYERED SAMPLE

NEGATIVE MULTI-LAYERED SAMPLE

NOTES:

1. BUILDING COMPONENTS CONTAINING

OVER 1% ASBESTOS IN THE MATERIAL

MATRIX ARE CONSIDERED

ASBESTOS-CONTAINING MATERIALS.

2. SAMPLE RESULTS OF BUILDING

MATERIALS EXCEEDING 1% ARE TO BE

CONSIDERED AS ASBESTOS-CONTAINING

MATERIALS.

3. L1/L2 REFERS TO MULTI-LAYERED

SYSTEMS WITHIN THE COMPOSITION

MATRIX OF THE SUSPECT MATERIAL.

Albuquerque, NM

Appendix D Certifications american board of industrial hygiene® organized to improve the practice of industrial hygiene proclaims that

Jose J. Sosa having met all requirements of education, experi~nce and examination, and ongoing maintenance, is hereby certified in the

COMPREHENSIVE PRACTICE

of

INDUSTRIAL HYGIENE

and has the right to use the designations

CERTIFIED INDUSTRIAL HYGIENIST

CIH

Certificate Number 5429CP

Awarded: December 9, 1991

Expiration Date: June 1, 2023

Chief Executive Officei,:A llI

Certificate of Achievement This certificate is awarded to:

Jose J. Sosa In recognition of satisfactory completion of the EPA-approved annual asbestos refresher training provided in accordance with the Model Accreditation Plan (MAP) (40 CFR Part 763, Subpart E, Appendix C) and AHERA of the Toxic Substances Control Act (TSCA) entitled:

Survey & Mechanical (Inspector) Course completion:

Examination Date:

Expiration Date:

Course Hours:

October 30, 2020 October 30, 2020

October 30, 2021

Instructor(s)

Danaya N. BenedettoDanaya N. Benedetto CEO & Training Program Manager

Credential License ID:

24895221

CHC Training Certificate No.

R20-1339-AI-O-FL

CHC Training Environmental Compliance Certification Experts www.chctraining.com 303.412.6360

855.60.CERTIFY

1775 W. 55th Avenue Denver, CO 80221

United States of America

FL Provider No. 0007238 FL Course No. 0006385

Aaron HixAaron Hix

4.0

Verify this Certificate Renew this Certificate

Halsey Beshears, SecretaryRon DeSantis, Governor

STATE OF FLORIDA

DEPARTMENT OF BUSINESS AND PROFESSIONAL REGULATION

ASBESTOS LICENSING UNIT

THE ASBESTOS CONSULTANT - ENGINEER HEREIN IS LICENSED UNDER THE

PROVISIONS OF CHAPTER 469, FLORIDA STATUTES

SOSA, JOSE J

Do not alter this document in any form.

10905 BRIDLE PL

LICENSE NUMBER: EA0000055

EXPIRATION DATE: NOVEMBER 30, 2022

This is your license. It is unlawful for anyone other than the licensee to use this document.

TAMPA FL 33626

Always verify licenses online at MyFloridaLicense.com https://www.myfloridalicense.com/LicenseDetail.asp?SID=&id=e8f692c4568dab619e9adcef50c4e0a7