14-Scope of Services PNC2129492R1.pdf

Scope of Services

Rotating List for Professional Engineering Testing Services

INTRODUCTION: Broward County Purchasing Division seeks qualified vendors to participate in a Rotating List, providing Professional Engineering Testing Services for various County agencies. Types of projects include, but not limited to: Renovations (some may be occupied), new Vertical Construction and Demolition of existing facilities. Testing services may require analysis of test results and reports of findings. See TESTING AND SERVICES section below for a list of services that may be needed, but are not guaranteed to be used or needed in the future.

A. ESTABLISHMENT AND USE OF LIST

A.1 Rotating List: The order of vendors in the initial rotation shall be established by using a List

Randomizer. When a testing service is needed, the first qualified vendor on the list shall be offered the job. If that vendor does not accept the job, or does not timely respond, or if the County, in its sole discretion, determines the vendor cannot perform the work, the next vendor shall be offered the job. This process shall be repeated until the job is accepted.

A.1.1 Subsequent testing service jobs will be offered to the next vendor on the initial rotation list after the vendor(s) previously awarded or offered a job.

A.1.2 Once the initial rotating list is exhausted, the list is then re-ordered based on the volume of work awarded. Testing service jobs will be offered to the vendor with the lowest County dollar value awarded for this QVL. This process is to equalize the dollar amounts awarded.

A.1.3 Poor performance by a vendor under this QVL may negatively affect future testing service job opportunities for this QVL. At the conclusion of each testing service, the County will complete a Vendor Performance Evaluation. Poor performance as documented in these evaluations may result in the vendor’s removal from the Qualified Vendor List (QVL) or a change in their position within the rotation. County reserves the right to include evaluations of vendors previous work to either remove or reprioritize the firm’s position in the rotation list.

A.2 Individual Testing Service Job Award Procedures:

A.2.1 County Using Agency reviews the list of available testing services.

A.2.2 County Using Agency contacts the Purchasing Division with testing service job information including the specific types of services required.

A.2.3 Purchasing Agent reviews request and offers the Using Agency the next eligible vendor on the list to contact for a proposal (based on rotation schedule, performance evaluations and pre-determined pricing).

A.2.4 Using Agency contacts the vendor for a proposal (vendor reviews request and establishes/agrees to tests, quantities, and delivery time).

NOTE: If the Contract Administrator, in their sole discretion, determines the vendor cannot perform the work or a minimum of three documented attempts to contact the vendor fail, the Using Agency will contact the Purchasing Agent for the next eligible vendor on the Rotating List to offer the job.

A.2.5 Using Agency submits the vendor’s proposal and funded requisition to the

Purchasing Division.

A.2.6 Using Agency and Purchasing Agent review the proposal for correct prices (same as established mean prices), ensure tests being used are included in the agreement, confirms current insurance for firm, and then issues a purchase order.

B. PRICING: Price will not be a factor in evaluating or ranking the interested firms. The County intends to negotiate pricing with the vendors qualified in Step-one. This process will commence in Step-two with an Invitation to Bid (ITB).

B.1 The County reserves the right to add tests in the future. When the County adds tests to the contract, a request for quotes will be sent to all awarded vendors and pricing negotiated.

C. ACRONYMS:

C.1 ASTM: American Society for Testing and Materials https://www.astm.org/

C.2 ACI: American Concrete Institute https://www.concrete.org/

C.3 AASHTO: American Association of State Highway and Transportation Officials https://transportation.org/

C.4 AMPP: The Association for Materials Protection and Performance https://ampp.org/home

C.5 ASM: ASM International https://www.asminternational.org/

C.6 API: American Petroleum Institute https://www.api.org/

C.7 ASME: American Society of Mechanical Engineers https://www.asme.org/

C.8 MDAD: Miami-Dade Aviation Department https://www.miami-airport.com/

C.9 DTPW: Miami-Dade Department of Transportation and Public Works https://www.miamidade.gov/global/transportation/home.page

C.10 DOH: Department of Health https://www.floridahealth.gov/

C.11 EPA: Environmental Protection Agency https://www.epa.gov/

C.12 FDOT: Florida Department of Transportation https://www.fdot.gov/

C.13 FAA: Federal Aviation Administration, Series 150 Advisory Circulars for Airport Projects

C.14 PCI: Precast/Prestressed Concrete Institute https://www.pci.org/

C.15 AMPP: Association for Materials Protection and Performance https://sspc.org/

C.16 TAS: Testing Application Standards:

International Code Council (ICC) https://www.iccsafe.org/ Florida Building Code (FBC) https://www.floridabuilding.org/

C.17 USGS: U.S. Geological Survey https://www.usgs.gov/

D. TEST AND SERVICES LIST: All testing labs all must be certified, and instrumentation calibrated;

presented by the testing vendor in the front end of any report provided. All tests shall include delivery of certified report which shall include but not be limited to: identification of testing equipment, laboratory certifications and calibration test date of equipment used, sampling and testing methodology, and a summary of results, findings and conclusions as they apply to the tests conducted for the project, (unless otherwise noted). Obtaining maintenance of traffic permits, approval, setting up and maintenance for field tests is incidental to the work being performed.

Definitions for Test and Services List Per Set: Pricing includes number of referenced items per set, e.g. 3 Specimens, 5 Cylinders.

D.1 Asphalt Concrete

1. Paving Mix Design, ASTM D6926-20 and ASTM D6927-22; Per Mix

2. Asphalt Paving Design Mix Marshall Method (Includes Sampling, Standard Design and

Applicable Marshall Procedures) per Asphalt Institute Manual Series No. 2; Per Mix

3. Inspection of Stackpole (Reclaimed Asphalt), ASTM D979/D979M; Per Hour

Follow current FDOT QA/QCD inspection guidelists and National Asphalt Pavement Association (NAPA) Quality Improvement Series 129 Best Practices for RAP and RAS Management

4. Marshall Properties, FDOT Procedures (Technician plus Tests): Stability ASTM D1559 or

AASHTO T 245; Per Set (Set of 3 Specimens)

5. Marshall Properties, FDOT Procedures (Technician plus Tests: Flow ASTM D1559 or

AASHTO T 245; Per Set (Set of 3 Specimens)

6. Marshall Properties, FDOT Procedures (Technician plus Tests): Density ASTM D2726; Per

Set (Set of 3 Specimens)

7. Marshall Properties, FDOT Procedures (Technician plus Tests): Air Voids ASTM D2726;

Per Set (Set of 3 Specimens)

8. Marshall Properties, FDOT Procedures (Technician plus Tests): Maximum Density ASTM

D2041; Per Sample

9. Marshall Properties, FDOT Procedures (Technician plus Tests): Particle Coating ASTM

D2489; Per Sample

10. Marshall Properties, FDOT Procedures (Technician plus Tests): Sampling/Preparation

ASTM D-1559 / D2726; Per Sample

11. Marshall Properties, FDOT Procedures (Technician plus Tests): Bulk Specific Gravity of

Drilled Core ASTM D2726; Per Core

12. Marshall Properties, FDOT Procedures (Technician plus Tests): Moisture Content, Drying ASTM C566; Per Sample

13. Marshall Properties, FDOT Procedures (Technician plus Tests): Moisture Content, Distillation ASTM D1461; Per Sample

14. Marshall Properties, FDOT Procedures (Technician plus Tests): Asphaltic Specific Gravity

/ Absorption of Aggregate Blends; ASTM D7370/D7370M-14(2021) Per Aggregate Sample

15. Marshall Properties, FDOT Procedures (Technician plus Tests): Sampling Hot Mix at

Manufacturer ASTM D979; Per Hour

16. Marshall Properties, FDOT Procedures (Technician plus Tests): Effect of Water on Hot

Mix ASTM D1075; Per Set (Set of 6 Samples)

17. Marshall Properties, FDOT Procedures (Technician plus Tests): Washed Sieve Analysis

AASHTO T 11 or AASHTO T 27; Per Sample

18. Marshall Properties, FDOT Procedures (Technician plus Tests): Coating and Stripping of

Bitumen-Aggregate Mixtures AASHTO T182; Per Sample

19. Marshall Properties, FDOT Procedures (Technician plus Tests): Flat / Elongated Pieces in Coarse Aggregate ASTM D4791; Per Sample

20. Marshall Properties, FDOT Procedures (Technician plus Tests): Effect of Moisture On Hot

Mix ASTM D4867; Per Set (Set of 6 Samples)

21. Marshall Properties, FDOT Procedures (Technician plus Tests): Sand Equivalent ASTM

D2419; Per Sample

22. Marshall Properties, FDOT Procedures (Technician plus Tests): Effect of Water on

Cohesion ASTM D1075 / Modified; Per Sample

23. Extraction/Graduation Analysis ASTM D6307; Per Test

24. Batch Plant Inspection, ASTM D979/D979M; Per Hour

25. On-Site Paving Operation Inspection per FDOT Procedures, FDOT construction project administration manual, Chapter 11; (Temperature, Density Testing and Observation); Per Hour (Minimum 4 Hours)

26. Bulk Specific Gravity/Densities (nuclear back scatter method) of Asphalt Core, ASTM D2950/D2950M-14; Per Test (Minimum 4 Tests)

27. Core Drilling for Thickness Measurements (Includes Asphalt Patching), ASTM

C174/C174M-17; Per Core (Minimum 6 Cores per Call-Out)

28. Asphalt Cores Laboratory Tests for Measurements ASTM D3549 and Weight per Cubic

Foot ASTM D2726 (minimum 4 Cores); Per Core

29. Gyratory Compaction (Bulk Specific Gravity), ASTM D6925-15; Per Sample

30. Asphalt Plant Technician Using FDOT Approved Plant, Laboratory and Procedures for

Extraction, Gradations, Marshall Tests and Temperature Checks, FDOT Asphalt Plant Level II and Aspahlt Mix Designer Certificate of Qualifications; Per Hour (Per Person, Minimum 4 Hours)

D.2 Asphalt Cement

31. Penetration of Bituminous Materials ASTM D5; Per Test

32. Abson Method, Recovery of Asphalt by Solution ASTM D1856; Per Test

33. Absolute Viscosity ASTM D2171; Per Test

D.3 Concrete Testing

34. Cylinders – Cast and Tested by Laboratory: Standard 6"x12" or 4"x 8" Cylinder.

(Concrete Temperature Test and Slump Test) (Per ASTM C31 "Section 7" Lab.

Strength Tests per ASTM C39 using C617 or C1231); Per Cylinder

35. Cylinders – Cast and Tested by Laboratory: Lightweight 3” x 6” Cylinder ASTM C495;

Per Cylinder

36. Cylinders – Cast and Tested by Laboratory: Air Entrainment per ASTM C231 used

Concurrently with Concrete Set Testing; Per Set (5 Cylinders Per Set)

37. Cylinders – Cast and Tested by Laboratory: Cylinder Pick-Up, ASTM 192 and C39; Per

Set (5 Cylinders Per Set)

38. Securing Structural or Pavement Cores ASTM C42 (6” maximum diameter): 8" Deep;

Per Core (Minimum 3 Cores)

39. Securing Structural or Pavement Cores ASTM C42 (6” maximum diameter): 14" Deep;

Per Core (Minimum 3 Cores)

40. Securing Structural or Pavement Cores ASTM C42 (6” maximum diameter): 12" Deep x 12" diameter; Per Core (Minimum 3 Cores)

41. Cores-Trim and Compression Test ASTM C42; Per Test

42. Concrete Masonry Units and Related Units ASTM C140 Block/Brick: Brick, Concrete;

Compression; Per Brick (Minimum 2 Bricks)

43. Concrete Masonry Units and Related Units ASTM C140 Block/Brick: Brick, Concrete;

Absorption; Per Brick (Minimum 2 Bricks)

44. Concrete Masonry Units and Related Units ASTM C140 Block/Brick: Brick, Concrete;

Dimension; Per Brick (Minimum 2 Bricks)

45. Concrete Masonry Units and Related Units ASTM C140 Block/Brick: Brick, Concrete;

Appearance; Per Brick (Minimum 2 Bricks)

46. Concrete Masonry Units and Related Units ASTM C140 Block/Brick: Block, Manhole, Test; Per Test

47. Concrete Masonry Units and Related Units ASTM C140 Block/Brick: Block, Concrete

Masonry Test; Per Test

48. Concrete Masonry Units and Related Units ASTM C140 Block/Brick: Block, Concrete

Compression, Individual Units; Per Test

49. Concrete Masonry Units and Related Units ASTM C140 Block/Brick: Block, Concrete

Absorption, Individual Units; Per Test

50. Concrete Masonry Units and Related Units ASTM C140 Block/Brick: Block, Concrete

Moisture Content; Per Test

51. Concrete Masonry Units and Related Units ASTM C140 Block/Brick: Mortar Cubes 2" x 2" x 2" Compression Test per ASTM C109 (Cast by awarded vendor); Per Test (Minimum 3 Cubes per Test)

52. Concrete Masonry Units and Related Units ASTM C140 Block/Brick: Drying Shrinkage

Test of Concrete Block ASTM C426 Per Test

53. Concrete Masonry Units and Related Units ASTM C140 Block/Brick: Moisture

Condition of Concrete Block ASTM C427 (Humidity); Per Test

54. Concrete Masonry Units and Related Units ASTM C140 Block/Brick: Block Series, Dimensions, Compression, Absorption, Moisture Content and Unit Weight (Density) per ASTM C140; Per Test

55. Concrete Masonry Units and Related Units ASTM C140 Block/Brick: Concrete or

Mortar Grout 3” x 3” x 6”, Prism Test; Per Test

56. Concrete Masonry Units and Related Units ASTM C140 Block/Brick: Full Block Prisms;

Per Test

57. Concrete Masonry Units and Related Units ASTM C140 Block/Brick: Masonry Prisms

ASTM C1314 (Fabricated by awarded vendor) (Unfilled); Per Prism

58. Concrete Masonry Units and Related Units ASTM C140 Block/Brick: Sampling and

Pick-Up (Casting Not Included); Per Unit

59. Concrete Masonry Units and Related Units ASTM C140 Block/Brick: Concrete Block

Unit Weight ASTM C140; Per Block

60. Concrete Masonry Units and Related Units ASTM C140 Block/Brick: Grout Cube

Compression Test ASTM C1014 (Cast by Others); Per Cube

61. Concrete Masonry Units and Related Units ASTM C140 Block/Brick: Technician to Cast Mortar or Grout Cubes in Laboratory or On-Site (Includes Slump & Temp Tests) ASTM C1019; Per Hour

62. Concrete Masonry Units and Related Units ASTM C140 Block/Brick: On-Site Masonry

Inspector per ACI 530.1; Per Hour (Minimum 4 hours)

63. Concrete Beams: Compression Test ASTM C116; Per Test

64. Concrete Beams: Tension Test ASTM C496 (Splitting Tension Test for Cylindrical

Specimen, not Beams); Per Test

65. Concrete Beams: Flexural Test per ASTM C78 Cast per ASTM C31, (2 Beams

Required per Test); Per Test

66. Concrete Cubes: Compression Test, 2” Cubes in Laboratory, ASTM C109/C 109M-02

Each

67. Concrete Cubes: Making Cubes on Field Jobs ASTM C109/C 109M-02 ; Per Hour

68. Concrete Rebound Hammer Tests Services of Technician and Concrete Rebound

Hammer: Swiss Hammer, ASTM C805/C805M-18; Per Hour (2 Hour Minimum)

69. Concrete Rebound Hammer Tests Services of Technician and Concrete Rebound Hammer: Overtime, ASTM C805; Per Hour

70. Air Content, Volumetric ASTM C173, C231; Per Hour

71. Concrete Yield & Density (Unit Weight) Test ASTM C138; Per Test

72. Design Mix ACI 211 Standard Aggregate (Materials Furnished by Supplier) (Laboratory

Sampling Included); Per Test (1 Trial Batch and 6 Cylinder Tests) (First of Any Series)

73. Design Mix Materials Testing: Gradation, ASTM C136/C136M-19 and ASTM C117-17;

Per Test

74. Design Mix Materials Testing: Fine Aggregate Gravity and Absorption ASTM C127; Per

Test

75. Design Mix Materials Testing: Coarse Aggregates Specific Gravity and Absorption

ASTM C128; Per Test

76. Design Mix Materials Testing: LA Abrasion ASTM C88; Per Test

77. Site Inspection ACI 304 and ACI 311.5R (Per Site Visit as Approved by the Engineer);

Per Hour (Minimum 4 Hours)

78. Concrete Plant Inspection ACI 311.5 (Mix and Weight Verification); Per Hour (Minimum 4 Hours)

79. Windsor Probe Test ASTM C803 (Penetration Resistance to Determine Uniformity) with Equipment Charge (Windsor Gun) (Per Trip Per Location); Per Hour

80. Thickness of Concrete (Ultrasonic Testing) ASTM C1383; Per Hour

81. Concrete Rebound Hammer Test ASTM C805/C-805M-13a; Per Hour (Minimum 4

Hours)

82. Pullout Strength ASTM C900-14 (Includes Pin Installation); Per Test

83. Penetration Resistance (Set of 3 Probes/Test) ASTM C803/C803M-03 (2010); Per Hour

84. Resonant Frequency ASTM C215-14; Per Hour

85. Pulse Velocity ASTM C597-09; Per Hour

86. Magnetic Measure Converter; ASTM A977/A977M-07(2020) Per Hour

87. Load Testing ACI 318-11; Per Test

88. Acoustic Emission, ASTM E3100-22; Per Hour

89. Pulse Echo, ASTM C1383/E797/E797M-21; Per Hour

90. Radiographics, ASTM E1742/E1742M-18; Per Hour

91. Concrete Radiographic: X-ray Cobalt 60 Radiography ASTM E592; Per Hour (2

Technicians)

92. Concrete Radiographic: X-ray Cobalt 60 Radiography ASTM E592, After Hours; Per

Hour (2 Technicians)

93. Concrete Radiographic: X-rays Scanning Iridium 192 Radiography ISO 5579; Per

Hour (2 Technicians)

94. Concrete Radiographic: X-rays Scanning Iridium 192 Radiography ISO 5579, After Hours; Per Hour (2 Technicians)

95. Ground Penetrating Radar (GPR) scans ASTM D6432; Per Hour (2 Technicians)

96. Ground Penetrating Radar (GPR) scans ASTM D6432, After Hours; Per Hour (2

Technicians)

97. Concrete Carbonation Test (Carbo Detect TM System by James Instruments); Per

Core

98. Concrete pH test ASTM D4262; Per Core

99. Corrosion Activity ASTM C876-09; Per Hour

100. Chloride Content: Per ASTM C1152; Per Test

101. Chloride Content: Per ASTM C1218; Per Test

102. Petrography ASTM C856-14 (Adjunct C856 known as ADJCO856); Per Test

103. Magnetometer Readings for Rebar Identification,; Per Hour (Minimum 4 Hours)

104. Floor Flatness (FF) and Floor Levelness (FL) Testing ASTM E1155-96 (2008); Per

Test

105. Concrete Moisture Testing ASTM F2170; Per Test

106. Concrete Moisture Testing ASTM F1869 (Only to be performed with Item #105, ASTM

F2170 – as a set); Per Test

D.4 Prestress / Precast

107. Prestress/Precast Fabrication Inspection PCI MNL-116 or MNL-117 (Bridge and Building Units/Ready Mix Plant Inspections); Per Hour (Minimum 4 Hours)

108. Prestress (Inspection & Certification Report Included) (Stressing Operation and

Inspection) per PCI MNL-116; Per Hour (Minimum 4 Hours)

109. Reinforced Concrete (Inspection & Certification Report Included); Per Hour (FDOT

QA/QC Inspection Guidelists)

110. Absorption Test of Precast Units ASTM C497; Per Hour

111. Testing Concrete Cylinder for Concrete Pipe, Manhole Sections or Tile per ASTM

C497. (Does NOT Include Technician or Pick-Up); Per Cylinder

112. Reinforced Concrete Pipe and Pre-Fabricated Manhole Inspection (Types, Sizes, and

Design) (Includes Inspection and Certified Report); ASTM C76 Per Hour (Minimum 4 Hours); FDOT Drainage Manual

113. Three Edge Bearing Test per ASTM C497; Per Hour

114. Hydrostatic Testing per ASTM C497; Per Hour

D.5 Piling

115. Wave Equation Analysis for Piles; Per Pile

116. Geotechnical Engineering Review Pile Installation Plan; Per Hour

117. Geotechnical Engineering Analysis of PDA Data by Case Wave Pile Analysis Program;

Per Hour

118. Geotechnical Engineering Review of awarded vendor’s Pile Certification Package; Per

119. Pile Driving Analyzer (PDA) On-Site Data Collection; Per Hour

120. Vibration Monitoring Services (Includes Equipment Capable of Detecting Velocities of

0.1 Inches Per Second and Certified Reporting); Per Hour

121. Drill Shaft Inspector (Certification Report Included); Per Hour

122. Pile Driving/Auger Cast Pile Inspection (Certification Report Included); Per Hour

(Minimum 4 Hours)

123. Vibroflotation Inspection; Per Hour (Minimum 4 Hours)

124. Piling Load Testing: Test Frame and Load Set-up ASTM D1143 (Equipment / Loads to be Furnished by awarded vendor); Per Hour

125. Piling Load Testing: Furnishing Calibrated Jack up to 4,000 lbs. Pile Manufacturing

Inspector (2 Hour Minimum), includes concrete cylinder tests; Per Jack Hour

126. Piling Load Testing: Furnishing and Set-up of Calibrated Gauges; Per Gauge

127. Piling Load Testing: Monitoring of Pile Load Test, Collect Field Data, and Inspector

Time; Per Hour

128. Piling Load Testing: Pile Load Test Report, Certify and Prepare Report for Load

Capacity of Pile (Engineer's Time); Per Hour

D.6 Geotechnical Services

129. Mobilization of Truck-Mounted Drill Rig; Per Day

130. Soil Borings; Per Foot

131. Auger Borings ASTM D1452: Penetration Depth 0' to 50'; Per Foot

132. Auger Borings ASTM D1452: Penetration Depth 51' to 75'; Per Foot

133. Auger Borings ASTM D1452: Penetration Depth 76' to 100'; Per Foot

134. Auger Borings ASTM D1452: Penetration Depth 101' to 150'; Per Foot

135. Rock Core Drilling ASTM D2113: Penetration Depth 0' to 50'; Per Foot

136. Rock Core Drilling ASTM D2113: Penetration Depth 51' to 75'; Per Foot

137. Rock Core Drilling ASTM D2113: Penetration Depth 76' to 100'; Per Foot

138. Rock Core Drilling ASTM D2113: Penetration Depth 101' to 150'; Per Foot

139. Unconfined Compressive Strength of Rock ASTM D2938; Per Inch-pound

140. Borings Standard Penetration ASTM D1586, with or without Casing Penetration Depth

0' to 50'; Per Foot

141. Borings Standard Penetration ASTM D1586, with or without Casing Penetration Depth

51' to 75'; Per Foot

142. Borings Standard Penetration ASTM D1586, with or without Casing Penetration Depth

76' to 100'; Per Foot

143. Borings Standard Penetration ASTM D1586, with or without Casing Penetration Depth

101' to 150'; Per Foot

144. Borings Standard Penetration Test, Portable Equipment; Includes Mobilization & Soil

Boring Report Per Foot

145. DOH Standard (Septic); Per Test

146. Slug Percolation Test USGS 9" Dia. Hole; Per Test (Minimum 2 Tests)

147. Double Ring Infiltration Test ASTM D3385; Per Test (Minimum 2 Tests)

148. Percolation Test: Open Hole Method (minimum 6" Dia.); Per Test (Minimum 3 Tests)

149. Percolation Test: DOH and Rehabilitative Services, Chapter 403; Per Test (Minimum

2 Tests)

150. Trench Test (per South Florida Water Management District) (Excludes Equipment and

Operator) (Provide Equipment Rental Invoice for Direct Cost Reimbursement); Per Test

151. Soil Cement Stabilization Field Inspection; Per Hour

152. Soil Cement Cylinder Testing ASTM D1633; Per Test

153. Water Quality Monitoring; Per Sample

154. Geotechnical Engineer Evaluation and Report of Existing Soil with Respect to

Allowable Bearing Capacity; Per Hour

155. Undisturbed Sampling ASTM D1586; Per Sample

156. Closing Holes with Grout / Approved Method(s) to Safe Proof Site [Safe proof to be accomplished before laboratory leaves the site(s)]; Per Lineal Foot

157. Geotechnical Engineer Pile Capacity Analysis; Per Hour

158. Muck Probes; Per Hour

159. Well Abandonment Grout Filling Complying with DOH and FDEP Standards Includes required capping at well head. Depth 0' to 50'; Per Foot

160. Well Abandonment Grout Filling Complying with DOH and FDEP Standards Includes required capping at well head. Depth 51' to 75'; Per Foot

161. Well Abandonment Grout Filling Complying with DOH and FDEP Standards Includes required capping at well head. Depth 76' to 100'; Per Foot

162. Well Abandonment Grout Filling Complying with DOH and FDEP Standards Includes required capping at well head. Depth 101' to 150'; Per Foot

163. Well Abandonment Permitting, Documentation, and Final Report by a Licensed

Engineer; Per Project

D.7 Soil

164. Field Density Test: Sand Cone Method AASHTO T191, ASTM D1556; Per Test (Minimum 2 Tests)

165. Nuclear Method AASHTO T238, T239, ASTM D2922, D3017 (minimum 4 tests): Per

Test (From 1 thru 4 Tests), Per Trip; Per Test

166. Nuclear Method AASHTO T238, T239, ASTM D2922, D3017 (minimum 4 tests): Per

Test (From 5 thru 10 Tests), Per Trip; Per Test

167. Nuclear Method AASHTO T238, T239, ASTM D2922, D3017 (minimum 4 tests): Per

Test (From 11 or more Tests), Per Trip; Per Test

168. Moisture Density (Proctor) Test: Standard AASHTO T99, ASTM D698 (Non-Traffic

Areas); Per Test (Minimum 2 Tests/Trip)

169. Moisture Density (Proctor) Test: Modified AASHTO T180, ASTM D1577

(Building/Highway Projects); Per Test (Minimum 2 Tests/Trip)

170. Moisture Content; Per Test

171. Limerock Bearing Ratio (LBR) FDOT; Per Test

172. Carbonates per Sample on LBR Material; Per Test (Minimum 2 Tests/Trip)

173. Laboratory California Bearing Ration (CBR) ASTM D1883: One (1) Point CBR; Per

Test

174. Laboratory California Bearing Ration (CBR) ASTM D1883: Lab Proctor Test; Per Test

175. Laboratory California Bearing Ration (CBR) ASTM D1883: Three (3) Point CBR; Per

Test

176. Field CBR ASTM D4429 (Reaction Loads by Others); Per Test (Minimum 2 Tests)

177. Density Test, Minimum / Maximum and Relative ASTM D4253, D4254; Per Test

178. Organic Content of Limerock AASHTO T267 (By Incineration); Per Test

179. Organic Content Soil Chemical Analysis (By Peroxide); Per Test

180. Grain Size AASHTO T27 (Sieve Analysis Only); Per Test

181. Mechanical Analysis ASTM D422, AASHTO T11, T27; Per Test

182. Soil Classification ASTM D3282, D2487; Per Test

183. Los Angeles Abrasion ASTM C131 (Small-Size Coarse Aggregate); Per Test

184. Los Angeles Abrasion ASTM C535 (Large-Size Coarse Aggregate); Per Test

185. Soundness of Aggregates ASTM C88 (Sodium Sulfate); Per Test

186. Sieve Analysis ASTM C136, FDOT, FAA Item F-211; Per Test

187. Absorption of Fine Aggregate ASTM C128, of Coarse Aggregate ASTM C127; Per

Test

188. Determination of Lead ASTM E2051; Per Test

189. Specific Gravity of Fine Aggregate ASTM C128, of Coarse Aggregate ASTM C127;

Per Test

190. Specific Gravity of Soil Solids by Water Pycnometer ASTM D854; Per Test

191. Bulk Density (Unit Weight) ASTM C29; Per Test

192. Material Finer than No. 200 Sieve ASTM C117; Per Test

193. Liquid Limit ASTM D4318 (Atterberg Limits); Per Test

194. Plastic Limit ASTM D424 (Atterberg Limits); Per Test

195. Organic Color Metric ASTM C117; Per Test

196. Salt Content FDOT FM 5-516; Per Test

197. Limerock Base Thickness Determination, minimum 3 inch diameter holes FAA Item P

211 (Excludes Mobilization and Transportation); Per Test (Minimum 2 Tests)

198. Limerock Base Thickness Determination, minimum 3 inch diameter holes FAA Item P

211 (Excludes Mobilization and Transportation): Unlimited Tests; Per Day

199. Limerock Chemical Analysis DTPW, FDOT; Per Test (Minimum 2 Tests)

200. Limerock Chemical Analysis DTAD, FAA Item P-211; Per Test

201. Sediment Tests; Per Test

202. Soil Load Bearing Test (Plate Load) (Reaction Load by Others): Static Load on

Footings ASTM D1194; Per Test

203. Soil Load Bearing Test (Plate Load) (Reaction Load by Others): Repetitive Static Load for Pavement ASTM D1195; Per Test

204. Soil Load Bearing Test (Plate Load) (Reaction Load by Others): Non-repetitive Static Load for Pavement ASTM D1196; Per Test

205. Soil Fill Test; Per Test

206. Soil Relative Density Test (Vibroflotation – In-Situ Verification - Standard Penetration

Test Soil Borings (SPT); Per Foot

207. Soil Relative Density Test (Vibroflotation – In-Situ Verification - Cone Penetration Test

Soundings (CPT); Per Foot

208. Resistivity Test in Accordance with California Method 643-7 with Breakdown for Test, Sampling, PH Measurement of Water and Soil, etc.; Per Test

209. Horticultural Service for PH Value of Soil; Per Test

210. Horticultural Service for Soluble Salts in Soil; Per Test

211. Horticultural Service for Macro Nutrients in Soil; Per Test

212. Backfill Monitoring; Per Hour (Minimum 4 Hours)

213. Geotechnical Engineer; Per Hour (Minimum 2 Hours)

D.8 Steel (Use ASM, AWS, ASME, API as applicable)

214. Shop or Field Weld Inspector ASTM D5339; Per Hour (Minimum 4 Hours)

215. Field or Shop Welding Inspector; Per Hour

216. Welder Test AWS, ASME Per connection at all positions; Per Connection

217. Reinforcing Steel Tensile Test ASTM D615; Per Test

218. Reinforcing Steel Deformation Test ASTM D615; Per Test

219. Reinforcing Steel Bend Test ASTM D615; Per Test

220. Reinforcing Bar Placement Inspection; Per Hour

221. Chemical Laboratory Test ASTM D615; Per Test

222. Welding Inspection and Dye Penetrant Well Testing; Per Hour

223. Engineering Services: Special Inspector for Threshold Buildings (State Certified); Per Hour (Minimum 2 Hours)

224. Engineering Services: Special Inspector’s Designee; Per Hour (Minimum 2 Hours)

225. Engineering Services: Special Inspector under South Florida Building Code; Per Hour

(Minimum 2 Hours)

226. Radiograph Weld Inspection; Per Test (Minimum 4 Tests)

227. Notched Bar Impact Testing of Metallic Materials (Fracture/Non-Fracture Critical Locations, Zone 1) ASTM E23; Per Test

D.9 Roofing (All tests to be performed per the latest edition of the Florida Building Code unless noted otherwise)

228. Moisture Content ASTM D1864; Per Test

229. Location of Wet Insulation in Roofing Systems using Infrared Imaging ASTM C1153 -

First 25 roofing squares (2,500 Sq. Ft.); Per Job

230. Location of Wet Insulation in Roofing Systems using Infrared Imaging ASTM C1153 – Each Additional roofing square (100 Sq. Ft.); Per Square Foot

231. Flood Testing Horizontal Waterproofing Installations ASTM D5957; Per Hour

232. Sampling and Analysis of New Built-Up Roof Membranes ASTM D3617; Per Test

233. Compression Test-Roof Tiles ASTM C1492; Per Hour

234. Absorption Test-Roof Tiles ASTM C1492; Per Set (5 Tiles Per Set)

235. Tile Uplift Test TAS 106 First Test; Per Job

236. Tile Uplift Test TAS 106 Additional Tests; Per Test

237. Core Samples ASTM D2829; Per Sample

238. Visual Inspections - First 2,500 Sq. Ft.; Per Job

239. Visual Inspections - Additional per Square Foot; Per Square Foot

240. Infrared Survey ASTM C1153 - First 2,500 Sq. Ft.; Per Job

241. Infrared survey ASTM C1153 - Additional per Square Foot; Per Square Foot

242. Nuclear Moisture Testing TAS 126-95 - First 2,500 Sq. Ft.; Per Job

243. Nuclear Moisture Testing TAS 126-95 - Additional per Square Foot; Per Square Foot

244. Impedence Moisture Survey (Machine) ASTM D7954 - First 2,500 Sq. Ft.; Per Job

245. Impedence Moisture Survey (Machine) ASTM D7954 - Per Square Foot (Additional

Sq. Ft. Survey); Per Square Foot

246. Non-Destructive Moisture Survey ASTM D7954, (TAS) No. 126-95, using a Tramex

Dec Scanner; Per Hour

247. Fastener Withdrawal Tests TAS No. 117(A)-95; Per Hour

248. Bell Chamber Test TAS 124-11; Per Test (2 Tests Minimum)

249. Bell Chamber Test TAS 124-11 - Additional Tests; Per Test

250. Bonded Pull Test TAS 124-11; Per Test (2 Tests Minimum)

251. Bonded Pull Test TAS 124-11 - Additional Tests; Per Test

252. Engineer’s Report; Per Hour

D.10 Mechanical

253. Sound Surveys (Includes Travel Time); Per Hour

254. Lighting Surveys (Includes Travel Time); Per Hour

D.11 Asbestos Testing

255. PLM (Polarized Light Microscopy); Per Test

256. PCM (Phase Contrast Microscopy); Per Test

257. TEM (Transmission Electron Microscopy); Per Test

258. Administrative Set-up (scheduling and administration for Asbestos Testing); Per Hour

259. Industrial Hygiene Technician and Certified Industrial Hygienist, Asbestos Survey, Sample Collection and Report Preparation; Per Hour

260. Florida Licensed Asbestos Consultant, Signed and Sealed Report; Per Report

D.12 Electric Tests Dielectric Tests of Safety Protection Equipment and Insulating Oils (at one voltage)

261. Gloves, Rubber Linemen; Per Pair

262. Overshoes or Blankets, Rubber Linemen; Each

263. Line-Hose, Rubber Insulator; Each

264. Hoods or Test Caps, Rubber Insulating; Each

265. Protectors, Rubber Insulating; Each

266. Insulated Jumpers; Each

267. Sleeves, Rubber Insulating; Per Pair

268. Skull-Guards, Protective; Each

269. Transformer Oils, Insulating; Per Sample

270. Dielectric Breakdown (general) (to 60,000 Root Mean Square (RMS) volts); Per

Puncture

D.13 Fireproofing: Inspection of Sprayed-On Fireproofing Coating on Structural Steel

271. Normal working hours; Per Hour (Minimum 4 Hours)

272. Overtime (Weekends, holidays and after hours); Per Hour

273. Laboratory Unit Weight Test of Fireproofing Coating ASTM E-605; Per Test

274. Field Adhesion / Cohesion Tests per ASTM E-736; Per Test

275. Field Inspection or Testing of Firestopping Assemblies or Materials ASTM E2174

(Firestops) or E2393 (Joint Systems or Perimeter Fire Barriers); Per Hour

D.14 Metallurgical Tests & Examinations

276. Mechanical Properties ASTM A225, E92, E18; Per Test

277. Corrosion and Surface Coating ASTM A219, A262; Per Test

278. Metallographic Tests ASTM E2, E3, E19, E45, E79, E89, E91, E112, A247, A317, B276 and SAE Recommended Practices; Per Test

279. Cause of Failure Examinations: Laboratory/Letterhead/Library Literature Search; Per

D.15 Radiographic Inspection & Testing Field Radiography

280. Services of 2-Person Radiographic Crew, Portable Darkroom and Equipment Complete; Per Hour (2 Hour Minimum)

281. Film Charge (4-1/2” x 10” and 3-1/2” x 17”); Each

282. Film Charge (8” x 10” and 14” x 17”); Each

283. Laboratory Radiology - Radiographic Inspection of Items Delivered to Lab; Per Hour

D.16 Strain Measurements (SR4 Indicator)

284. Technician to Install Gauges and Make Strain Reading; Per Hour (2 Hour Minimum)

D.17 Ultrasonics Inspection

285. Ultrasonic Technician and Equipment; Per Hour (2 Hour Minimum)

286. Assistant Technician; Per Hour (2 Hour Minimum)

D.18 Structural Steel

287. Welding Inspector, AWS Certified; Per Hour (2 Hour Minimum)

288. Structural Steel Shop or Field Inspector; Per Hour (2 Hour Minimum)

289. Bolt Tightening Inspection by using Torque Wrench; Per Hour

290. Bolt Tightening Inspection by using Regular Wrench; Per Hour

291. Bolt Tightening Inspection by using Filler Gauge; Per Hour

292. Standard Test for Liquid Penetrant Examination ASTM E165 & E1417; Per Square

Foot

293. Standard Test for Magnetic Particle Testing ASTM E1444 & E709; Per Square Foot

294. Notched Bar Impact Testing of Metallic Materials (Fracture/Non-Fracture Critical

Locations, Zone 1 ASTM E23; Per Test

D.19 Welding

295. Welding Inspector, AWS Certified; Per Hour (2 Hour Minimum)

296. Welding Inspection Team, AWS Certified/1 Hour PADI Certified (Minimum 2

Inspectors per Inspection); Per Hour

297. Diving Tank (Minimum 2 Inspectors); Per Hour

298. Support Boat with Tender, Fuel, Consumable Supplies and Ramp Fees; Per Hour

299. Underwater Video with landside Operator; Per Hour

D.20 Magnetic Particle Testing-Magnaflux

300. Magnaflux Testing ASTM E1444; Per Test

301. Magnaflux Non-Destructive Services; Technician; Per Hour

D.21 Underground Utility Location and Inspection

302. Utility Designation – Electronically scan and determine the horizontal and vertical location of buried utility lines; Per Hour

303. Expose utility line by using an Air/Vacuum System that creates a small diameter hole.

Provide separate CADD drawing for each test hole, indicating its horizontal and vertical location, the type of utility, its size, and the materials of construction. The test holes shall be plotted on base maps to scale. The work shall be reviewed and certified by a Florida Registered Land Surveyor. Included in this item are any costs associated with restoration. In Pavement; Per Test Hole

304. Expose utility line by using an Air/Vacuum System that creates a small diameter hole.

Provide separate CADD drawing for each test hole, indicating its horizontal and vertical location, the type of utility, its size, and the materials of construction. The test holes shall be plotted on base maps to scale. The work shall be reviewed and certified by a Florida Registered Land Surveyor. Included in this item are any costs associated with restoration. In Soil; Per Test Hole

D.22 Glazing and Exterior Systems Tests

305. Water Penetration Resistance Test ASTM E1105; Per Hour

306. Air Leakage Site Detection ASTM E1186; Per Hour

307. Air Leakage Site Detection ASTM E783; Per Hour

308. Water Penetration Resistance Test, Dynamic Pressure AAMA 501.1; Per Hour

309. Water Penetration Resistance Test, Field Water Spray AAMA 501.2; Per Hour

D.23 Painted Surfaces

310. Standard Test for Detection of Lead in Paint and Dried Films ASTM D3618; Per Test

311. Standard Test for Measuring Adhesion by Tape Test ASTM 3359; Per Test

312. Standard Test for Pull-Off Strength of Coating using Portable Adhesion Tester ASTM

D4541; Per Test

313. Soluble Salt Test AMPP-Guide 15 using Class A Retrieval Method; Per Test

314. Measure Soluble Salt Concentration AMPP-Technical Update 4; Per Test

315. Bridge Coating Inspector (BCI) AMPP Certified Level 2; Per Hour

316. Standard Test for Field Measurement of Surface Profile of Blast Cleaned Steel ASTM

D4417; Per Test

D.24 Air Quality

317. Visual Determination of Fugitive Emissions from Material Sources and Smoke Emissions from Flares (FDOT 561-10.2.3.1); Per Day

318. Total Suspended Particulate Matter Testing (FDOT 561-10.2.3.2); Per Day

D.25 Professional Engineering for Testing Services

319. Principal Engineer; Per Hour

320. Senior Engineer; Per Hour

321. Project Engineer; Per Hour

322. CADD Technician; Per Hour

323. Clerical; Per Hour

324. Senior Technician; Per Hour

[This space intentionally left blank]