09/16/25 Smith Seckman Reid, Inc.

Equipment Solution Planning - ESP Harris Health Smith Clinic - MRI

Specification Coversheet

Item #: BBS278200 Alt ID:

Description: Biopsy System, Breast Manufacturer: Hologic, Inc. Model: Sapphire

Basic: Furnish Install: O/O Drawings: N

Arch Code: 3 - Minor movable Arch Sig: N

Lead time:

Physical Requirements Mounting: Mobile Clear. left:

Width: 25.00 in Right:

Height: 37.00 in Top:

Depth: 21.00 in Bottom:

Weight: 100.00 lb Front:

Back: Door swing:

Rough in:

Electrical Requirements Volts: 120 Watts: 1320

Hz: 60 BTU/HR:

Phase: Single Amps 11

UPS: N Data: N

Ded. Circuit: N Compressed Air: N

Connection: NEMA 5-15P

Utility Requirements Hot Water: N Cold Water: N

Spec. Water: N Vent: N

Steam: N Gases: N

Drain: N Vacuum: N

* This cover sheet is for quick reference only. For full technical specification details please refer to the attached vendor document.

Qty N/E Ord Floor/Room Room Name Department Notes 1 Exist No Control Level 4 - MRI

ATEC® Breast Biopsy and Excision System: Sapphire™ Unit Operator’s Manual 28

Specifications

ATEC® Breast Biopsy and Excision System:

Sapphire™ Unit

Size 25 in. Wide (63cm) 25 in. Wide (63cm)

37 in. High (93cm) 37 in. High (93cm)

21 in. Deep (53cm) 21 in. Deep (53cm)

Footprint (Width x Depth) 525 in2 (3400 cm2) 525 in2 (3400 cm2)

Weight 100 lbs. (45kg) 100 lbs. (45kg)

Maximum Power 1320W 1200W

Voltage 120V AC 240V AC

Frequency 60 Hz 50 Hz

Maximum Current 11 A 5 A

Fuse 12 A, Breaker 6 A, Breaker

Power Cord Length 15 ft. (5m) 15 ft. (5m)

Vacuum Generated 28”Hg (71cmHg) 28”Hg (71cmHg) at sea level at sea level

ATEC® Footswitch – MRI Compatible

Size 6 in. (16cm) Long

4 in. (9cm) Wide

2 in. (5cm) High

Weight 1 lb. (0.5kg)

Tubing Length 20 ft. (6m)

ATEC® Handpiece

Handpiece Size 1.6 in. (4cm) diameter x 10 in. (26cm) long

Weight 7 oz. (204g)

Needle Length 4 in. (9cm); 5 in (12cm); 6 in. (14cm)

Outer Cannula Diameter 12g – 0.106 in. (3mm); 9g – 0.146 in. (4mm)

Inner Cannula Diameter 12g – 0.079 in. (2mm); 9g – 0.118 in. (3mm)

Aperture Length 0.787 in. (20mm); 0.472 in. (12mm)

Tubing Set Length 15 ft. (5m) for US/STX handpiece

20 ft. (6m) for MRI handpiece

Sterilization Gamma Irradiation

120V/60 Hz Model 240V/50 Hz Model cnichols

SSR RECTANGLE

ATEC® Breast Biopsy and Excision System: Sapphire™ Unit Operator’s Manual

Storage and Transport Environmental Requirements

An ambient temperature of -29 degree to +60 degree Celsius

A relative humidity range of 30% to 85% excluding condensation

An atmospheric pressure range of 500hPa to 1060hPa

Equipment Operating Environmental Conditions

An ambient temperature of +15 degree to +40 degree Celsius

A relative humidity of 30% to 75%

Operating altitude: less than or equal to 3,657 meters above sea level

Classification

Type of protection against electric shock: Class I

Degree of protection against electric shock: Type BF

Degree of protection against the ingress of water: Ordinary

Mode of Operation: Continuous

More Information

For product availability, labeling limitations and more information, contact your Suros Sales

Representative or call Suros Customer Support toll free at 877-887-8767. If you are an international customer, please contact your distributor for more information. Product information can also be found on the Suros website at www.SurosSurgical.com.

Equipment Solution Planning - ESP Harris Health Smith Clinic - MRI

Specification Coversheet

Item #: CHR-10194 Alt ID:

Description: Chair, Phlebotomy, Bariatric Manufacturer: Clinton Industries Inc. Model: Bariatric

Basic: Furnish Install: O/O Drawings:

Arch Code: 2 - Major movable Arch Sig: N

Lead time: 90 days

Physical Requirements Mounting: FS Clear. left:

Width: 53.00 in Right:

Height: 36.00 in Top:

Depth: 29.00 in Bottom:

Weight: Front:

Back: Door swing:

Rough in:

Electrical Requirements Volts: Watts:

Hz: BTU/HR:

Phase: Amps

UPS: N Data: N

Ded. Circuit: N Compressed Air: N

Connection: N/A

Utility Requirements Hot Water: N Cold Water: N

Spec. Water: N Vent: N

Steam: N Gases: N

Drain: N Vacuum: N

* This cover sheet is for quick reference only. For full technical specification details please refer to the attached vendor document.

1 New No Control Level 4 - MRI

Lab X Series, Bariatric, Blood Drawing Chair with Padded Flip Arm and Drawer

Limited Warranty

MODEL 66002B

• �Padded, true, bariatric seat features extra width and depth for added comfort

• Comfortable padded arched backrest

• Height and depth adjustable, padded flip arm

• �Flip arm(s) positions in place when in use, then flips out of the way for easy exit

• ClintonClean™ elbow rest

• ClintonClean™ drawer top

• Height-adjustable, one-piece, all-plastic drawer

• A full 35" wide seat (89 cm)

• �1-1/4” square, heavy duty, all-welded, tubular steel frame (3.18 cm)

• Comfortable 2” padding throughout (5 cm)

• Neutral Gray powder-coated frame

• Easy-clean, durable vinyl in a selection of colors

• ClintonClean™ arms option available

• �700 lbs. combined load capacity under normal use (317.8 kg)

IMPORTANT NOTE: Clinton Blood Drawing Chairs are not engineered to restrain a fainting or falling occupant.

The chair’s occupant should NEVER be left unattended.

ORDERING NOTE: MUST add arm suffix number to model number when ordering any model with arm option, otherwise chair will be shipped as shown.

All blood drawing products are non-returnable unless they are unused in unopened, original packaging.

MODEL 66002B SPECIFICATIONS

Seat 35" W x 21" D x 20” H

Overall 53" W x 29" D x 36"H

Arm Height Range 27" — 33"

Arm Adjustment 6"

Standard Upholstery Colors

OPTIONS

665 ClintonClean™, Armrest and Flip Arm(s)

Warning for:

• Pediatric Vinyl Stickers

• Products with Vinyl Stickers

• Cabinets

• Tables and Physical Therapy Racs with Edgebanding

Warning for:

• Stools without Chrome Bases or Chrome Parts,

• Wood Treatment Tables

• All products with Standard Vinyl or Fire-Rated Vinyl

Warning for:

• Chrome Accessories

• Phlebotomy Products

• Power Tables

• Stainless Steel products

LABEL 1

LABEL 2

LABEL 3

Limited Warranty

Slate Blue Wedgewood Royal Blue Desert Tan Burgundy Country Mist Warm Gray Gunmetal Black

California residents please be advised of the following, pursuant to Proposition 65:

Equipment Solution Planning - ESP Harris Health Smith Clinic - MRI

Specification Coversheet

Item #: CHR39301 Alt ID:

Description: Chair, Phlebotomy, Reclining Manufacturer: Marketlab Inc. Model: ML10666

Basic: Furnish Install: O/O Drawings:

Arch Code: 3 - Minor movable Arch Sig: N

Lead time:

Physical Requirements Mounting: Clear. left:

Width: 31.00 in Right:

Height: 50.00 in Top:

Depth: 43.00 in Bottom:

Weight: 52.00 lb Front:

Back: Door swing:

Rough in:

Electrical Requirements Volts: Watts:

Hz: BTU/HR:

Phase: Amps

UPS: N Data: N

Ded. Circuit: N Compressed Air: N

Connection: N/A

Utility Requirements Hot Water: N Cold Water: N

Spec. Water: N Vent: N

Steam: N Gases: N

Drain: N Vacuum: N

Remarks Item should sit about 24" from the wall in order to have full clearance.

* This cover sheet is for quick reference only. For full technical specification details please refer to the attached vendor document.

1 Exist No Control Level 1 - MRI

Reclining!Phlebotomy Chair

ML10666

Dimensions: 31"W x 43"D x 50"H

Description:

! Superb design and quality materials provide an extremely comfortable draw for your patient

! Recline to Trendelenburg position to improve patient stabilization

! Removable side panels allow for easy access to recliner for cleaning and maintenance

! Comprehensive manufacturer warranty

! The range of motion allows this chair to recline into numerous positions

The Reclining Phlebotomy Chairs are so comfortable, your patients will want to take one home with them.

Designed with extra-thick cushioning, contour seat and back, footrest, and infinite positioning, your patient is sure to be relaxed and appropriately supported during the draw. Should your patient faint during collection, you can actuate the chair into the Trendelenburg position from either side to stabilize them. Not only was this family of Phlebotomy Chairs designed with patient in mind, but the phlebotomist as well.

The folding side trays for supplies, the lockable swivel casters and easy recline operation makes these Phlebotomy Chairs tech-friendly as well. Lifetime warranty on frame; three year warranty on parts. Some assembly required.

! 350lb capacity

! Upholstered armrests extend to the back to give improved support in the Trendelenburg position

! Fold-down side tables accommodate draw supplies

! Arrest caps protect walls from marring

! Foot pedal located on BOTH sides of chair to actuate reclining

! Tente® swivel casters move chair anywhere and can be locked into place for stability

! Integrated footrest reclines with the seat

! 5” leg extensions available (ML5487)

Equipment Solution Planning - ESP Harris Health Smith Clinic - MRI

Specification Coversheet

Item #: CHR39310 Alt ID:

Description: Chair, Phlebotomy Manufacturer: Marketlab Inc. Model: ML15923-DB

Basic: Furnish Install: O/O Drawings:

Arch Code: 3 - Minor movable Arch Sig: N

Lead time: 60 days

Physical Requirements Mounting: Clear. left:

Width: 35.00 in Right:

Height: 37.00 in Top:

Depth: 30.00 in Bottom:

Weight: 60.00 lb Front:

Back: Door swing:

Rough in:

Electrical Requirements Volts: Watts:

Hz: BTU/HR:

Phase: Amps

UPS: N Data: N

Ded. Circuit: N Compressed Air: N

Connection: N/A

Utility Requirements Hot Water: N Cold Water: N

Spec. Water: N Vent: N

Steam: N Gases: N

Drain: N Vacuum: N

* This cover sheet is for quick reference only. For full technical specification details please refer to the attached vendor document.

,-./0.10234567-2897:;<-41402=;::02>1.?2@7.51

�������A�� ��B

��CA�D���C��D��EC��B����!���'�

FGHHIJJ2K24.������

L.1-2MN�O��P��*��

QRSRTU

���#�V'��

)�� WD��%

X����"��� ������Y�����#

Z[\]̂_̀ab

ML15923-DB

,-./0123145

��$6�� ����6�������

&'��)���7'� �"���6���*'�����������$��6���%�$6�� �������6�

8�����6��������*9��'$�������������� ����6�%���

���7'� �������><�?�@<*��<A

B�����6'��)*'������ ����������%����������������6��������*9��'$�������������� ����6�%���

(��9�����%�$6��

C2-/1D1/E3145.

F0GHI-1JK3L ><�

�7'�

F..-GMNOHP-QR10-SL ����$��

TE2E/13OL ����"� T4R530OH4DHU01J15L ��

TR.34G1VEMN-L W� I-1JK3HFSXR.3EM1N13OL �@#�<�*���<

YPHC3E3R.L W�

��Z���6� UR3-0H,1G-5.145H,-23KL ��<

UR3-0H,1G-5.145HI-1JK3L �>< UR3-0H,1G-5.145H[1S3KL ��<

C-E3HI-1JK3HD04GH\N440L �;< C-E3H[1S3KL ��<

[E00E53OL ]�� [-1JK3L ��"�

[-1JK3Ĥ1G13L ����"�

T4G2N1E5/-H_H[E0515J.

,-./0123/-4521647849-23/3:;�<��������'%

?1@4A-B4C.D14E/FG

,.G2/H-.4AGI/H-.4E-JG.D

K����

L/6M,.1D@2G4N6GH/OG34P-:D

K����

,-2I

K����

Equipment Solution Planning - ESP Harris Health Smith Clinic - MRI

Specification Coversheet

Item #: CRT03114 Alt ID:

Description: Cart, Procedure, General Manufacturer: Armstrong Medical Industries, Inc. Model: ABL-B-4

Basic: Furnish Install: Drawings:

Arch Code: 3 - Minor movable Arch Sig: N

Lead time: 60 days

Physical Requirements Mounting: Mobile Clear. left:

Width: 32.50 in Right:

Height: 39.75 in Top:

Depth: 25.00 in Bottom:

Weight: 135.00 lb Front:

Back: Door swing:

Rough in:

Electrical Requirements Volts: Watts:

Hz: BTU/HR:

Phase: Amps

UPS: N Data: N

Ded. Circuit: N Compressed Air: N

Connection: N/A

Utility Requirements Hot Water: N Cold Water: N

Spec. Water: N Vent: N

Steam: N Gases: N

Drain: N Vacuum: N

* This cover sheet is for quick reference only. For full technical specification details please refer to the attached vendor document.

Armstrong Medical Industries, Inc. – ABL-B-4

Standard Steel Solid Color Emergency Carts Standard Steel Beige 4-Drawer, Breakaway Lock, 24in.

Product No: ABL-B-4

• Overall dimensions: 39 3/4"H x 25"D x 33 1/2"W (includes bumper/handles/casters)

• Drawer heights: 3"H (2), 6"H (1), 12"H (1)

• Drawer size: 17 1/16"D x 22 1/4"W

• Double Side-Wall Construction

• Push handles (2)

• TENTE Casters

• Locking casters (2)

• Swivel caster

• Tracking caster

• Stabilizing frame with bumper

• Ball Bearing Drawer Slides

• Carts require some assembly.

Equipment Solution Planning - ESP Harris Health Smith Clinic - MRI

Specification Coversheet

Item #: DET386701 Alt ID:

Description: Detector, Metal, MRI, Screener Manufacturer: Metrasens Model: Ferroguard Assure

Basic: Furnish Install: O/C Drawings:

Arch Code: 1.5 - Spec sheet Arch Sig: N

Lead time: 60 days

Physical Requirements Mounting: W Clear. left:

Width: 3.25 in Right:

Height: 54.00 in Top:

Depth: 3.50 in Bottom:

Weight: 10.00 lb Front:

Back: Door swing:

Rough in:

Electrical Requirements Volts: 120 Watts: 28

Hz: 60 BTU/HR:

Phase: Single Amps 0.2

UPS: N Data: Y

Ded. Circuit: Y Compressed Air: N

Connection: HW

Utility Requirements Hot Water: N Cold Water: N

Spec. Water: N Vent: N

Steam: N Gases: N

Drain: N Vacuum: N

Remarks Item has the option to have a left or right door swing install

* This cover sheet is for quick reference only. For full technical specification details please refer to the attached vendor document.

Qty N/E Ord Floor/Room Room Name Department Notes

Ferroguard Assure & MRISM Installation Checklist & Cut Sheet (Left Handle)

This document contains Metrasens proprietary information and all content is © Metrasens Ltd. 2019 Revision 1/7/21 Page 1 of 6.

Metrasens Inc | Lisle Business Center | 2150 Western Court, Suite 360 | Lisle, IL 60532 USA | Tel: +1 (630) 541-6509 | info@metrasens.com | www.metrasens.com mailto:info@metrasens.com http://www.metrasens.com/

This document contains Metrasens proprietary information and all content is © Metrasens Ltd. 2019 Revision 1/7/21 Page 2 of 6.

Metrasens Inc | Lisle Business Center | 2150 Western Court, Suite 360 | Lisle, IL 60532 USA | Tel: +1 (630) 541-6509 | info@metrasens.com | www.metrasens.com

This document contains Metrasens proprietary information and all content is © Metrasens Ltd. 2019 Revision 1/7/21 Page 3 of 6.

Metrasens Inc | Lisle Business Center | 2150 Western Court, Suite 360 | Lisle, IL 60532 USA | Tel: +1 (630) 541-6509 | info@metrasens.com | www.metrasens.com

This document contains Metrasens proprietary information and all content is © Metrasens Ltd. 2019 Revision 1/7/21 Page 4 of 6.

Metrasens Inc | Lisle Business Center | 2150 Western Court, Suite 360 | Lisle, IL 60532 USA | Tel: +1 (630) 541-6509 | info@metrasens.com | www.metrasens.com

This document contains Metrasens proprietary information and all content is © Metrasens Ltd. 2019 Revision 1/7/21 Page 5 of 6.

Metrasens Inc | Lisle Business Center | 2150 Western Court, Suite 360 | Lisle, IL 60532 USA | Tel: +1 (630) 541-6509 | info@metrasens.com | www.metrasens.com

Pre-Installation Actions & Requirements - to be completed by MR Facility electricians, before arrival of Metrasens Field Service Engineer:

1) MRI magnet ramped 100%. ☐

2) Site contacts provided (see Page-6). ☐

3) Multiple ceiling tiles will be removed and remain out during the installation and calibration process. ☐

4) Stepladder made available for Metrasens Engineer to access Hub in ceiling during Final Installation. ☐

5) Hub: 1 - Photograph must be provided to Metrasens ☐

a. Hub installed by an electrician above ceiling just above the Zone-4 entry door. ☐

b. AC power connected to Hub via Isolation Switch. ☐

c. AC power confirmed as working - the green light will illuminate when the Isolation switch is turned ON. ☐

6) Magnetic Sensor Units (a.k.a. ‘poles’): 2 - Photographs must be provided to Metrasens (1 - for the Left Side and 1 - for the Right Side) ☐

a. (1) 1.25” holes with conduit and pull strings on the-left side entry of the MRI doorway (No J-boxes). ☐

b. (1) 1.25” hole with conduit and pull string on the right-side entry of the MRI doorway (No J-boxes). ☐

c. Pull strings from left side & right-side pole cable holes installed through to Hub via conduit. ☐

d. Obstructions removed to allow poles to mount on wall (signs, switches, guard rails). ☐

7) ODAS Door Sensor: 1 - Photograph must be provided to Metrasens ☐

a. (1) 1.25” hole with conduit and pull string drilled - at 10" from Hinge side of door, NOT handle side, flush, no J-boxes. ☐

b. Pull string installed through to Hub (via conduit).

8) MRISM Touchscreen: 1 - Photograph must be provided to Metrasens ☐

a. (1) 1.25” hole with conduit and pull string drilled under control desk - flush, no J-boxes. A power outlet MUST be within 12” of the hole. ☐

b. Pull string installed through to Hub (via conduit) Unless cables are routed via surface mounted. ☐

c. Desk grommet present below touch screen mounting position. ☐

9) Door Entryway: 1 - Photograph must be provided to Metrasens ☐

a. Please be sure there is at least 4” of clearance on the left and right side of the MRI door near the corner edges of the door frame. ☐

10) Total Pictures provided to Metrasens – 6. ☐

11) Ferroguard unit onsite and unopened. ☐

*NOTE: Installations are performed Monday thru Friday 8:00am – 5:00pm local time. If the Prework is not completed upon the arrival of the Metrasens installer, an additional Travel Fee of $3,100 will be assessed for a return visit.

This document contains Metrasens proprietary information and all content is © Metrasens Ltd. 2019 Revision 1/7/21 Page 6 of 6.

Metrasens Inc | Lisle Business Center | 2150 Western Court, Suite 360 | Lisle, IL 60532 USA | Tel: +1 (630) 541-6509 | info@metrasens.com | www.metrasens.com

MRI Contact

Name

Cell

Site contact for the installation process (if different then MRI contact)

Training Contact

Electrician

Security

Other Contact

Ferroguard Assure & MRISM Installation Checklist & Cut Sheet (Right Handle)

This document contains Metrasens proprietary information and all content is © Metrasens Ltd. 2019 Revision 1/7/21 (USA) Page 1 of 6.

Metrasens Inc | Lisle Business Center | 2150 Western Court, Suite 360 | Lisle, IL 60532 USA | Tel: +1 (630) 541-6509 | info@metrasens.com | www.metrasens.com

This document contains Metrasens proprietary information and all content is © Metrasens Ltd. 2019 Revision 1/7/21 (USA) Page 2 of 6.

Metrasens Inc | Lisle Business Center | 2150 Western Court, Suite 360 | Lisle, IL 60532 USA | Tel: +1 (630) 541-6509 | info@metrasens.com | www.metrasens.com

This document contains Metrasens proprietary information and all content is © Metrasens Ltd. 2019 Revision 1/7/21 (USA) Page 3 of 6.

Metrasens Inc | Lisle Business Center | 2150 Western Court, Suite 360 | Lisle, IL 60532 USA | Tel: +1 (630) 541-6509 | info@metrasens.com | www.metrasens.com

This document contains Metrasens proprietary information and all content is © Metrasens Ltd. 2019 Revision 1/7/21 (USA) Page 4 of 6.

Metrasens Inc | Lisle Business Center | 2150 Western Court, Suite 360 | Lisle, IL 60532 USA | Tel: +1 (630) 541-6509 | info@metrasens.com | www.metrasens.com

This document contains Metrasens proprietary information and all content is © Metrasens Ltd. 2019 Revision 1/7/21 (USA) Page 5 of 6.

Metrasens Inc | Lisle Business Center | 2150 Western Court, Suite 360 | Lisle, IL 60532 USA | Tel: +1 (630) 541-6509 | info@metrasens.com | www.metrasens.com

Pre-Installation Actions & Requirements - to be completed by MR Facility electricians, before arrival of Metrasens Field Service Engineer:

1) MRI magnet ramped 100%. ☐

2) Site contacts provided (see Page-6). ☐

3) Multiple ceiling tiles will be removed and remain out during the installation and calibration process. ☐

4) Stepladder made available for Metrasens Engineer to access Hub in ceiling during Final Installation. ☐

5) Hub: 1 - Photograph must be provided to Metrasens ☐

a. Hub installed by an electrician above ceiling just above the Zone-4 entry door. ☐

b. AC power connected to Hub via Isolation Switch. ☐

c. AC power confirmed as working - the green light will illuminate when the Isolation switch is turned ON. ☐

6) Magnetic Sensor Units (a.k.a. ‘poles’): 2 - Photographs must be provided to Metrasens (1 - for the Left Side and 1 - for the Right Side) ☐

a. (1) 1.25” holes with conduit and pull strings on the-left side entry of the MRI doorway (No J-boxes). ☐

b. (1) 1.25” hole with conduit and pull string on the right-side entry of the MRI doorway (No J-boxes). ☐

c. Pull strings from left side & right-side pole cable holes installed through to Hub via conduit. ☐

d. Obstructions removed to allow poles to mount on wall (signs, switches, guard rails). ☐

7) ODAS Door Sensor: 1 - Photograph must be provided to Metrasens ☐

a. (1) 1.25” hole with conduit and pull string drilled - at 10" from Hinge side of door, NOT handle side, flush, no J-boxes. ☐

b. Pull string installed through to Hub (via conduit).

8) MRISM Touchscreen: 1 - Photograph must be provided to Metrasens ☐

a. (1) 1.25” hole with conduit and pull string drilled under control desk - flush, no J-boxes. A power outlet MUST be within 12” of the hole. ☐

b. Pull string installed through to Hub (via conduit) Unless cables are routed via surface mounted. ☐

c. Desk grommet present below touch screen mounting position. ☐

9) Door Entryway: 1 - Photograph must be provided to Metrasens ☐

a. Please be sure there is at least 4” of clearance on the left and right side of the MRI door near the corner edges of the door frame. ☐

10) Total Pictures provided to Metrasens – 6. ☐

11) Ferroguard unit onsite and unopened. ☐

*NOTE: Installations are performed Monday thru Friday 8:00am – 5:00pm local time. If the Prework is not completed upon the arrival of the Metrasens installer, an additional Travel Fee of $3,100 will be assessed for a return visit.

This document contains Metrasens proprietary information and all content is © Metrasens Ltd. 2019 Revision 1/7/21 (USA) Page 6 of 6.

Metrasens Inc | Lisle Business Center | 2150 Western Court, Suite 360 | Lisle, IL 60532 USA | Tel: +1 (630) 541-6509 | info@metrasens.com | www.metrasens.com

MRI Contact

Site contact for the installation process (if different then MRI contact)

Training Contact

Electrician

Security

Other Contact

Equipment Solution Planning - ESP Harris Health Smith Clinic - MRI

Specification Coversheet

Item #: DIS260314 Alt ID:

Description: Disposal, Sharps, Floor Cart Manufacturer: Stericycle Model: D-08 8gal Wire Dolly

Basic: Furnish Install: Drawings:

Arch Code: 3 - Minor movable Arch Sig: N

Lead time:

Physical Requirements Mounting: Clear. left:

Width: 14.25 in Right:

Height: 23.00 in Top:

Depth: 13.00 in Bottom:

Weight: Front:

Back: Door swing:

Rough in:

Electrical Requirements Volts: Watts:

Hz: BTU/HR:

Phase: Amps

UPS: N Data: N

Ded. Circuit: N Compressed Air: N

Connection: N/A

Utility Requirements Hot Water: N Cold Water: N

Spec. Water: N Vent: N

Steam: N Gases: N

Drain: N Vacuum: N

* This cover sheet is for quick reference only. For full technical specification details please refer to the attached vendor document.

Wire Step-On Dolly

Code # DWS-08, DWS-17, DWSH-17

For mobility and hands-free operation with the 8 or 17 gallon containers, push down on the step-on pedal of the wire dolly and the lid will open and close automatically.

Wire Dolly

Code # D-08

Constructed of a durable powder-coated steel, the wire dolly allows the 8 gallon container to be moved from one location to another.

Wire Wall Bracket

Code # WB-08

The locking wire wall bracket, constructed of a durable powder-coated steel, allows the 8 gallon container to be mounted to any vertical surface.

P R O T E C T I N G P E O P L E . R E D U C I N G R I S K . TM

Black Dolly

Code # D-17

Made of high density plastic, the 17 gallon black dolly makes mobility easy for the 17 gallon container. Wheels on this dolly make it ideal for emergency rooms, labs and operating rooms where mobility is important.

jshirley Rectangle jshirley Rectangle jshirley Rectangle

There is good reason thousands of healthcare providers turn to Stericycle Bio Systems.

We seek to protect people and reduce risk. Whether you’re a small or a large medical facility, a research facility, pharmaceutical or biotechnology facility, we can tailor our Stericycle Bio Systems Sharps Management Program to meet your sharps disposal needs.

Stericycle Bio Systems – Experts in Sharps Management

(888) 9•SHARPS

9 7 4 - 2 7 7 7

(Rev. 10/07) STC_BIOPRBRO_1007

Product Code Description Approximate Dimensions (Height x Depth x Width)

C-02RES-0203 2 gallon container (red) with vertical drop lid 15.1” x 4.73” x 12.5”

C-02RES-0203-OC 2 gallon container (red), vertical drop lid, outer cabinet (beige) and key 15.5” x 5.59” x 14.5”

OC-02-2004 2 gallon outer cabinet only (beige) 13.25” x 5.59” x 14.5”

C-03RES-0203 3 gallon container (red) with vertical drop lid 21.1” x 4.73” x 12.5”

C-03RES-0203-OC 3 gallon container (red), vertical drop lid, outer cabinet (beige) and key 21.5” x 5.59” x 14.5”

OC-03-2004 3 gallon outer cabinet only (beige) 19.25” x 5.59” x 14.5”

0203LIDX 2 & 3 gallon vertical drop lid 4.75 x 4.73” x 12.5”

0203WMA 2 & 3 gallon locking wall mount (beige) and key 2.75” x 5.75” x 13”

0203SB 2 & 3 gallon countertop stability base (beige) 4.25” x 7.01” x 11.99”

0203LIDX 4 gallon vertical drop lid 4.78” x 6.85” x 12.25”

04HORZ-2007 4 gallon horizontal drop lid 4.78” x 6.85” x 12.25”

C-04RES-04 4 gallon container (red) with vertical drop lid 21.25” x 6.75” x 11.75”

C-04RES-04HORZ 4 gallon container (red) with horizontal drop lid 21.25” x 6.75” x 11.75”

C-04RES-04-OC 4 gallon container (red), vertical drop lid, outer cabinet (beige) and key 21.81” x 7.47” x 14.5”

C-04RES-04HORZ-OC 4 gallon container (red), horizontal drop lid, outer cabinet (beige) and key 21.81” x 7.47” x 14.5”

OC-04-2004 4 gallon outer cabinet only (beige) 19.25” x 7.47” x 14.5”

WB-04 4 gallon locking wire wall bracket (red) and key 7.12” x 7.75” x 13.62”

C-08-2004LR 8 gallon container only (red) 19.7” x 12.95” x 11.25”

08FT-2004 8 gallon funnel top lid 1.25” x 11.25” x 11.25”

08TT-2004 8 gallon trap top lid 1” x 11.25” x 11.25”

WB-08 8 gallon wire wall bracket (red) 21.5” x 13.25” x 14”

D-08 8 gallon wire dolly (red) 23” x 13” x 13.5”

DWS-08 8 gallon wire step-on dolly (red) 23” x 16.5” x 14.25”

C-17 17 gallon container only (red) 24.75” x 17.5” x 13.25”

L-17 17 gallon transport lid (black) 17.25” x 12.62”

L2-17 17 gallon 2 part slide top lid (black) 17.25” x 12.62”

LH-17 17 gallon hamper top lid (black) 17.25” x 12.62”

DWS-17 17 gallon wire step-on dolly (red) for 2 part slide top lid 29.75” x 22.5” x 14.5”

DWSH-17 17 gallon wire step-on dolly (red) for hamper top lid 29.75” x 22.5” x 14.5”

D-17 17 gallon black dolly (black) 9.75” x 19” x 14.25” www.stericycle.com

P R O T E C T I N G P E O P L E . R E D U C I N G R I S K . TM

Product Codes jshirley Rectangle jshirley

Equipment Solution Planning - ESP Harris Health Smith Clinic - MRI

Specification Coversheet

Item #: DIS54014 Alt ID:

Description: Disposal, Sharps, Wall Mounted Manufacturer: Daniels Model: Sharpsmart S22

Basic: Furnish Install: Drawings:

Arch Code: 1.5 - Spec sheet Arch Sig: Y

Lead time:

Physical Requirements Mounting: W Clear. left:

Width: 15.50 in Right:

Height: 17.25 in Top:

Depth: 8.25 in Bottom:

Weight: Front:

Back: Door swing:

Rough in:

Electrical Requirements Volts: Watts:

Hz: BTU/HR:

Phase: Amps

UPS: N Data: N

Ded. Circuit: N Compressed Air: N

Connection: N/A

Utility Requirements Hot Water: N Cold Water: N

Spec. Water: N Vent: N

Steam: N Gases: N

Drain: N Vacuum: N

* This cover sheet is for quick reference only. For full technical specification details please refer to the attached vendor document.

Qty N/E Ord Floor/Room Room Name Department Notes 2 Exist No Control Level 1 - MRI

Equipment Solution Planning - ESP Harris Health Smith Clinic - MRI

Specification Coversheet

Item #: DIS60906 Alt ID:

Description: Disposal, Sharps, Floor Bin Manufacturer: BD Medical Model: 305610 (17 gal container)

Basic: Furnish Install: O/O Drawings: N

Arch Code: 3 - Minor movable Arch Sig: N

Lead time: 40 days

Physical Requirements Mounting: Clear. left:

Width: 19.50 in Right:

Height: 23.50 in Top:

Depth: 14.25 in Bottom:

Weight: 5.00 lb Front:

Back: Door swing:

Rough in:

Electrical Requirements Volts: Watts:

Hz: BTU/HR:

Phase: Amps

UPS: N Data: N

Ded. Circuit: N Compressed Air: N

Connection: N/A

Utility Requirements Hot Water: N Cold Water: N

Spec. Water: N Vent: N

Steam: N Gases: N

Drain: N Vacuum: N

Remarks 5 per case $185 ($37 each)

* This cover sheet is for quick reference only. For full technical specification details please refer to the attached vendor document.

Qty N/E Ord Floor/Room Room Name Department Notes 1 Exist No MRI Level 4 - MRI 1 Exist No MRI Level 1 - MRI

Equipment Solution Planning - ESP Harris Health Smith Clinic - MRI

Specification Coversheet

Item #: DSP03400 Alt ID:

Description: Dispenser, Emesis Bag Manufacturer: Medline Industries Inc. Model: NONEMBGDISPH

Basic: Furnish Install: O/C Drawings:

Arch Code: 1.5 - Spec sheet Arch Sig: N

Lead time:

Physical Requirements Mounting: W Clear. left:

Width: 6.25 in Right:

Height: 6.50 in Top:

Depth: 6.25 in Bottom:

Weight: 2.00 lb Front:

Back: Door swing:

Rough in:

Electrical Requirements Volts: Watts:

Hz: BTU/HR:

Phase: Amps

UPS: N Data: N

Ded. Circuit: N Compressed Air: N

Connection: N/A

Utility Requirements Hot Water: N Cold Water: N

Spec. Water: N Vent: N

Steam: N Gases: N

Drain: N Vacuum: N

* This cover sheet is for quick reference only. For full technical specification details please refer to the attached vendor document.

Qty N/E Ord Floor/Room Room Name Department Notes

Emesis Bag Dispensers

DISPENSER, EMESIS BAG, WALL MOUNT

Holds up to 24 bags Bags not included

Packaging

Manuf

Manuf #

Specifications

COLOR Clear

DIMENSION INCHES 6-1/4 D x 6-1/2 H

HPIS CODE 520_190_0_0

LATEX FREE Yes

MATERIAL Abs

UNSPSC 47121707

Unit of Measure

Conversion Net/Gross Weight (lbs)

Volume (cubic ft)

Shipping Dimensions L x W x H(inch)

GTIN

Each (EA) 1.0 Each 0.0 / 2.0 0.171 6.5 x 6.5 x 7.0 10888277410930

Case (CS) 6.0 Each 0.0 / 8.9 1.343 20.225 x 13.5 x 8.5 20888277410937

HCPCS Information

HCPCS Disclaimer: HCPCS codes and Home Health Consolidated Billing codes provided by Medline are intended as general guidelines only. Medline does not guarantee coverage or reimbursement of any products.

You must address all coverage and reimbursement issues (including the correctness and accuracy of codes) with your individual payers. It is your responsibility to ensure the accuracy and appropriateness of each claim you submit, in accordance with all applicable payer requirements.

HCPCS Code: NO CODE - PRODUCT DOES NOT MEET HCPCS SPECIFICATIONS

NONEMBGDISPSKU

NONEMBGDISP

Medline

6 Each / Case

Safety Data Sheet Documents

No SDS content is available for this product.

Generated 08/21/2019

Equipment Solution Planning - ESP Harris Health Smith Clinic - MRI

Specification Coversheet

Item #: DSP21114 Alt ID:

Description: Dispenser, Glove, Triple Box Manufacturer: Medline Industries Inc. Model: MDS193096B

Basic: Furnish Install: O/C Drawings:

Arch Code: 1.5 - Spec sheet Arch Sig: N

Lead time: 30 days

Physical Requirements Mounting: W Clear. left:

Width: 15.75 in Right:

Height: 3.75 in Top:

Depth: 10.00 in Bottom:

Weight: 1.00 lb Front:

Back: Door swing:

Rough in:

Electrical Requirements Volts: Watts:

Hz: BTU/HR:

Phase: Amps

UPS: N Data: N

Ded. Circuit: N Compressed Air: N

Connection: N/A

Utility Requirements Hot Water: N Cold Water: N

Spec. Water: N Vent: N

Steam: N Gases: N

Drain: N Vacuum: N

Remarks Cost is $63.00 per case of 6

* This cover sheet is for quick reference only. For full technical specification details please refer to the attached vendor document.

Qty N/E Ord Floor/Room Room Name Department Notes 1 Exist No Control Level 4 - MRI 1 Exist No MRI Level 4 - MRI 2 Exist No Control Level 1 - MRI

+���",'-#%� �!."/'$�*'#%��"'$"�!$%�0�� 1'-#%�#2"/�$34�$!"#'%"�#0�-3!3 1!3��#!"�'2'"'#"'-%!$"(�#�)/

5�06�2�#2

1�#-(�0%-$!$

1�#-(�0%-$!$"7

89!0�(�0�%�'#)

:;5<=">?@=;8 ABCD"E

:>85;?8;F"<G5; H�'�!

=5>8"@I:; JDKLDKLKLK

=;>H=<">?@=;8 MK"E

=IN:>?H"O<G <$�9�!

N�<;P"QF;; G!)

1�<;F>�N @�!�$"5!%2"5��)%�0

R?858@ JMMKAJKS

+>:<=">?@=;8 MDBCD"E

T��� �U

���������� V��W�����

X��YZ�

U�]

_Z�����Y

X Z]

��aV

;�0/"[bc] MBK";�0/ KBK"d"KBeAA KBAJf ABCD"g"MDBCD"g"MKBK MKeeJAehMKDDCA

[�_] ijk b� Z kjk W ljk mjmin mkjk opjk opjk pkqqprqnokllsp

=@5@8">#('$,�%�'# tuvuwxyz{|}~z����xtuvuwx|���{x~��xt���xt�~}��xu��{�}z�~���x�z}}z��x|���{x����z���x��x���}z��x~�� z�������x~{x�����~}x��z��}z��{x��}��x���}z��x���{x���x��~�~����x|����~��x��x��z����{�����x��x~��x�����|�{� ���x��{�x~����{{x~}}x|����~��x~��x��z����{�����xz{{��{x�z�|}��z��x���x|����|���{{x~��x~||��~|�x��x|���{� �z��x����xz��z�z��~}x�~���{�x��xz{x����x��{���{z�z}z��x��x��{���x���x~||��~|�x~��x~������z~����{{x��x�~|�x|}~z� ���x{���z��xz�x~||���~�|�x�z��x~}}x~��}z|~�}�x�~���x����z������{� tuvuwxu����x��xu�y�x�xv��y�u�xy��wx���x����xtuvuwxwv�u� �u¡����w

��_onrkni�8¢R""

��_onrkni� i b� Z W

�̂ ����W_�_

?'"8:8"0'#%!#%"�)"������ �!"('$"%/�)"9$'3-0%B ooWoiWmkmk

Equipment Solution Planning - ESP Harris Health Smith Clinic - MRI

Specification Coversheet

Item #: DSP279515 Alt ID:

Description: Dispenser, Paper Towel, Surface Mount Manufacturer: Georgia Pacific Model: 8" Enmotion (59762)

Basic: Furnish Install: O/C Drawings:

Arch Code: 1.5 - Spec sheet Arch Sig: Y

Lead time: 60 days

Physical Requirements Mounting: W Clear. left:

Width: 13.32 in Right:

Height: 20.83 in Top:

Depth: 8.16 in Bottom:

Weight: 11.70 lb Front:

Back: Door swing:

Rough in:

Electrical Requirements Volts: Watts:

Hz: BTU/HR:

Phase: Amps

UPS: N Data: N

Ded. Circuit: N Compressed Air: N

Connection: Battery Powered

Utility Requirements Hot Water: N Cold Water: N

Spec. Water: N Vent: N

Steam: N Gases: N

Drain: N Vacuum: N

Electrical Notes Qty 4 D Batteries

* This cover sheet is for quick reference only. For full technical specification details please refer to the attached vendor document.

Qty N/E Ord Floor/Room Room Name Department Notes

./0123'45-6-3173' 0+1-3628'9:;4'<',1335465-'=63>'

:036:71+'12'1?10354'@638'AB'2:/,:'

@5C':4':036:71+'0;->',;33:7)

��� ��DB:-636:7';763':7'=1++'-:'3>13'3>5'3:0'6-'+5E5+)'F-5'

@5C'3:':057'94:73'2:E54'17?'/14@'-245='+:2136:7-'=>545' 67?62135?'=63>'2642+5-)'G52;45';763'3:'=1++'=63>'9:;4'172>:45?' -245=-'1004:046135'3:'3>5'3C05':9'=1++'67'+:2136:7-'045E6:;-+C' /14@5?)

H���I�� B:-636:7';763':7'=1++'-:'3>13'3>5'3:0'6-'+5E5+)'

J14@'+:2136:7-':9'->1?5?'1451-'->:=7)'K--5/,+5'3=:'LMN'

/:;7367O',412@53-'LPQRS(T'-:+?'-5014135+CN',C'2:7752367O'3>5'

-6?5-'1-'->:=7)'K+6O7'@5C>:+5'-+:3-'=63>'1451-'/14@5?' 045E6:;-+C)'U7-;45'3>13'3>5'144:=-':7'3>5',412@53'145'0:67367O' ;0=14?-)'B55+'V+/'94:/'3>5'1?>5-6E5':7'3>5',12@'-6?5'17?'=63>' V4/'045--;458'1?>545'3>5'1--5/,+5?'/:;7367O',412@53'3:'=1++)'

F-5'9:;4'LRN'172>:45?'-245=-'1004:046135'3:'3>5'3C05':9'=1++'67'

3>5'@5C>:+5'-+:3-'67?62135?'3:'-52;45',412@53)'W:2@'?6-057-54' 673:'0+125',C'O573+C'0;++67O'?:=7=14?)

J:;7367O'->:;+?'2:/0+C'=63>'K<K'O;6?5+675-)'X:/0+61725'6-' 3>5'45-0:7-6,6+63C':9'3>5'67-31++54)

YZ[\\]̂ _̀`̀abc̀d e������ � �����f ghi��hjkllmn�

#ghi��hop h �o�&q ���q"����q��� o gq r

�oq�gr s qi p r gpqp�riqg�r t̀u\[v̀wx̀xayz̀d{{̀|}~���̀|���|���z

Equipment Solution Planning - ESP Harris Health Smith Clinic - MRI

Specification Coversheet

Item #: DSP49306 Alt ID:

Description: Dispenser, Soap Manufacturer: Ecolab North America Model: Endure Bacti 92723188

Basic: Furnish Install: O/C Drawings:

Arch Code: 1.5 - Spec sheet Arch Sig: Y

Lead time:

Physical Requirements Mounting: W Clear. left:

Width: 7.50 in Right:

Height: 11.00 in Top:

Depth: 5.00 in Bottom:

Weight: Front:

Back: Door swing:

Rough in:

Electrical Requirements Volts: Watts:

Hz: BTU/HR:

Phase: Amps

UPS: N Data: N

Ded. Circuit: N Compressed Air: N

Connection: N/A

Utility Requirements Hot Water: N Cold Water: N

Spec. Water: N Vent: N

Steam: N Gases: N

Drain: N Vacuum: N

Remarks Sold by: Case of 6

* This cover sheet is for quick reference only. For full technical specification details please refer to the attached vendor document.

Qty N/E Ord Floor/Room Room Name Department Notes

Ecolab Endure Bacti 92723188

Manufacturer # 92723188

Brand Huntington®

Manufacturer Ecolab

Country of Origin United States

Application Hand Hygiene Dispenser

Capacity 750 mL

Color Cream

Dispenses Soap

Material Plastic

Mounting Type Wall Mount

Operating Method Manual Push

Equipment Solution Planning - ESP Harris Health Smith Clinic - MRI

Specification Coversheet

Item #: DSP49307 Alt ID:

Description: Dispenser, Soap Manufacturer: Ecolab North America Model: Nexa Compact Touchless

Basic: Furnish Install: O/C Drawings:

Arch Code: 1.5 - Spec sheet Arch Sig: Y

Lead time:

Physical Requirements Mounting: W Clear. left:

Width: 5.50 in Right:

Height: 9.34 in Top:

Depth: 3.97 in Bottom:

Weight: Front:

Back: Door swing:

Rough in:

Electrical Requirements Volts: Watts:

Hz: BTU/HR:

Phase: Amps

UPS: N Data: N

Ded. Circuit: N Compressed Air: N

Connection: Battery Powered

Utility Requirements Hot Water: N Cold Water: N

Spec. Water: N Vent: N

Steam: N Gases: N

Drain: N Vacuum: N

Detailed Specs Height with drip tray = 16.54 in.

* This cover sheet is for quick reference only. For full technical specification details please refer to the attached vendor document.

Qty N/E Ord Floor/Room Room Name Department Notes

1 New No Control Level 4 - MRI

There are 722,000 healthcare-associated infections (HAIs) in the

US each year.2

Hand Hygiene is the

#1 way to prevent healthcare-associated infections (HAIs).1

WHY FOCUS ON HAND HYGIENE?

Increased Hand Hygiene has been attributed to a

21% reduction in healthcare-associated infections (HAIs).3

Proper Hand Hygiene is a critical component to preventing the spread of diseases like COVID-19.4

Manual Dispensers

Touch-Free Dispensers

USE FEWER BATTERIES

Energy saving touch-free dispenser requires fewer battery change-outs.5

PUSH BAR PROTECTION

Antimicrobial works continuously to inhibit growth of bacteria6 that may affect the push bar. Smooth surface, no ridges or openings to collect debris or grime.

OPTIMIZE PRODUCT USE

Improved and uniquely designed packaging and collapsible bottle evacuates up to 99% of product to reduce product waste.

PREVENT COSTLY WASTE

Patented pump pulls excess product back in, reducing costly product clogs and drips and helps prevent potential slips and falls.

99%

OF PRODUCT

52%

BATTERIES

FEWER

Nexa™ Dispensers Easy, efficient hand hygiene.

The Nexa dispenser helps prevent the spread of germs with a dispensing system that provides efficiency, innovation and sustainability in one sleek and adaptable dispenser. Available in manual or touch-free.

� Proprietary packaging system delivers consistent, accurate dispensing

� Easy to access and load product with low and high dose settings

� Dispenses liquid and foam products for streamlined purchasing and inventory

� Clear side window provides easy usage monitoring and visible expiration date

� Indicator light monitors battery life

� Easily accessible battery pack requires no tools access for quick and simple changes

� Universal cartridge works in both manual and touch-free systems

� Dispenser badges for easy product identification

� Compatible with Ecolab's Hand Hygiene Compliance Monitoring technology to help improve hand hygiene compliance

Nexa™ DISPENSER

AND PRODUCT SOLUTIONS

1 Centers for Disease Control https://www.cdc.gov/media/pressrel/r021025.htm

2 HAI Data and Statistics. Centers for Disease Control and Prevention. https://www.cdc.gov/hai/surveillance/index.html

3 World Health Organization http://www.who.int/gpsc/5may/MDRO_literature-review.pdf

4 http://www.cdc.gov/coronavirus/2019-ncov/hcp/hand-hygiene.html

5 Over the course of 21 months at 50 activations per day, in comparative testing using Ecolab’s Nexa Touch-Free dispenser and leading competitor’s dispenser. Ecolab data on file.

6 Bacteria, mold and mildew that can cause degradation.

7 Centers for Disease Control and Prevention. Guideline for Hand Hygiene in Healthcare Settings: Recommendations of the Healthcare

Infection Control Practices Advisory Committee and the HICPAC/SHEA/APIC/IDSA Hand Hygiene Task Force. MMWR 2002;51

(No. RR-16).

8 Ecolab data on file.

©2021 Ecolab USA Inc. All rights reserved. 50251/0301/0221

TO LEARN MORE CALL 866.781.8787 OR VISIT ECOLAB.COM

Contact your Ecolab Representative to find out how Nexa dispensers can help improve efficiency, compliance and sustainability.

ECOLAB.COM

rmeiklejohn Rectangle rmeiklejohn Highlight rmeiklejohn Image

Equipment Solution Planning - ESP Harris Health Smith Clinic - MRI

Specification Coversheet

Item #: HMP06005 Alt ID:

Description: Hamper, Linen, MRI Manufacturer: Blickman Inc. Model: 7772MR Round

Basic: Furnish Install: O/O Drawings:

Arch Code: 3 - Minor movable Arch Sig: N

Lead time: 90 days

Physical Requirements Mounting: Mobile Clear. left:

Width: 20.00 in Right:

Height: 35.00 in Top:

Depth: 20.00 in Bottom:

Weight: 16.00 lb Front:

Back: Door swing:

Rough in:

Electrical Requirements Volts: Watts:

Hz: BTU/HR:

Phase: Amps

UPS: N Data: N

Ded. Circuit: N Compressed Air: N

Connection: N/A

Utility Requirements Hot Water: N Cold Water: N

Spec. Water: N Vent: N

Steam: N Gases: N

Drain: N Vacuum: N

Detailed Specs Part No. 0927772400

* This cover sheet is for quick reference only. For full technical specification details please refer to the attached vendor document.

Qty N/E Ord Floor/Room Room Name Department Notes

P A D D E D S T O O L S

F O O T S T O O L S

H A M P E R S

F I V E L E G I V S T A N D S

M A Y O S T A N D S

K I C K B U C K E T

S O L U T I O N S T A N D S

I N S T R U M E N T T A B L E S

Blickman has been honoring customer requests for MR-Safe

Equipment since the late-1990s. Its products, legendary for high quality and supported by an industry-unique Lifetime

Limited Warranty, have performed without incident. Blickman’s unblemished record of safety in the imaging industry owes to its faithfully adhering to guidelines first set forth in

1997 by the Center for Devices & Radiological Health

(CDHR) – Magnetic Resonance Group, part of the U.S. Food and Drug Administration.

In recent years, however, the imaging marketplace has been changing. Scanners of 3.0-Tesla strength were introduced.

Interventional radiology emerged as a growing practice, with more surgical procedures than ever before being performed within the MR suite. Concerns arose: Could formerly MR-Safe

Equipment keep pace with these new requirements? Could these traditional products continue to be used in safety?

The MR Task Group of the American Society for Testing and

Measurement International (ASTM) addressed these concerns from August, 2005 through March, 2006. It superseded historical CDHR guidelines with its new active standards, designed to clarify what it now means for equipment to be “MR-Safe.”

Previously, MR-Safe Equipment could be designated for use within particular “zones,” i.e., incremental distances from what had been 0.2-to-1.5-Tesla scanners. The ASTM eliminated such incremental designations. Now all MR-Safe Equipment must be suitable for use throughout the entire MR suite, including anywhere within the vicinity of 3.0-Tesla scanners.

Moreover, all healthcare equipment now must be labeled either “MR-Safe” or “Not MR-Safe,” depending upon whether it meets this new ASTM standard. This labeling is intended to help avoid any injuries or even deaths occurring within the MR suite.

Blickman Meets the Test

Shortly after ASTM announced its new standard in March, 2006, Blickman launched rigorous testing and re-engineering of its entire MR-Safe Equipment line. It engaged specialist professionals working in independent laboratories to determine the compliance of its products. As a result of its testing Blickman temporarily removed two of its formerly

MR-Safe products (which nevertheless, continue to satisfy the historical CDHR guidelines for today’s more prevalent

1.5-Tesla scanners.) However, the balance of Blickman’s

MR-Safe Equipment passed all testing with flying colors!

Blickman also integrated within its manufacturing a comprehensive marking process whereby all of its products are now visibly labeled either “MR-Safe” or “Not MR-Safe.”

The bottom line? Blickman can proudly state that all products displayed within this brochure are MR-Safe in full compliance with the new ASTM standard. You can continue to rest assured with the unparalleled high quality and safety of Blickman MR-Safe Equipment for your MR suite!

Blickman MR-Safe Equipment:

Fully-Compliant with the New ASTM Standards

MODELS 7772MR, 7772MR-PL HAMPERS have a round tubular ring that is seamlessly welded to three legs.

A solid, round platform on the bottom acts as a bracing and protects the hamper bag from contact with the floor. A reinforced, dome-shaped lid of high-density, white polyethylene (Model 7772MR-PL) is recommended to control airborne pathogens. All hampers move easily over floors on two-inch MR-Safe swivel casters.

Model No. Part No. Lid Dimensions (overall) Ship Wt. (lb) est.

7772MR 0927772400 none 20"D 35"H 20

7772MR-PL 0927772600 plastic 22"D 36-1/2"H 40

Optional Hamper Bags

HB18 9839777201 18" diameter bags

MODEL 7792MR FIVE-LEG IV STANDS feature a stainless-steel post that sits on a 24" diameter, polished die-cast aluminum base with wall-saver end caps to protect against scuffmarks. All five-leg IV poles offer a two- or four- hook interchangeable ram’s horn. Stands travel on two-inch MR-Safe swivel casters. Optional

1381MR push handle is available.

Model No. Part No. Type of Hooks Height Adj. Casters Ship Wt. (lb)

Adjustment est.

7792MR-C 0537792002 Twist lock 2 74"-110" 2" 35

7792MR-4C 0537792004 Twist lock 4 74"-110" 2" 35

MODEL 7741MR MAYO STAND is a superior choice for value-conscious customers. Adjustments are made with a Tru-LocTM friction knob for manual locking at desired height. Stands travel on two-inch MR-Safe swivel casters. Two tray sizes.

Model No. Part No. Feature Height Adjustment Tray Size Ship Wt. (lb) est.

7741MR-C 0637741200 Tru-LocTM knob 39-1/2"-62" 13-3/4" x 19" 45

7741MR-C

7772MR-PL

7792MR-C

DVanalstine

TEST SPECIFICATIONS

All Products in this Blickman “MR-Safe Equipment” brochure meet the revised “MR-Safe” definition as stated in ASTM standard F2503.

The configuration/design safety of the components of these Blickman products in the MR environment were verified in accordance with ASTM standard F2052-06: “Measurement of Magnetically-induced Displacement Force in the

MR Environment.”

The “paramagnetic” material property constraints of these Blickman products were determined through the test conducted by an independent lab in accordance with ASTM standard A773/A773M-01, employing a computer-automated, soft-magnetic, hysteresigraph system.

A low-µ permeability indicator gage, in compliance with ASTM standard A342/A342M, is used for final factory acceptance of these Blickman products.

Identification of these Blickman products conforms to the ASTM standard F2503-05: “Marking Medical Devices and

Other Items for Safety in the MR Environment.”

39 Robinson Road Lodi, NJ 07644 • 800-247-5070 • Fax: 201-909-0832 e-mail: info@blickman.com • www.blickman.com

PRODUCT LISTING

MR-Safe Equipment

Model No. Part No. Description Ship Wt. (lb) est.

7445MR 1027445000 MR Padded Stool 15"D (38.10) 21"H (53.34) on Rubber Tips 30*

7445MR-C 1027445001 MR Padded Stool 15"D (38.10) 23"H (58.42); 2" (5.08) MR Swivel Casters 30*

7757MR 1017757000 Foot Stool 12"D (30.48) 18"W (45.72) 8"H (20.32) 9*

7757MR-HR 1017757100 Foot Stool 12"D (30.48) 18"W (45.72) 8"H (20.32) with 41"H (104.14) Handrail 22*

7761MR 1017761000 Foot Stool 12"D (30.48) 30"W (76.20) 8"H (20.32) 19*

7761MR-HR 1017761100 Foot Stool 12"D (30.48) 30"W (76.20) 8"H (20.32) with 41"H (104.14) Handrail 32*

7763MR 1017763000 Donnelly Foot Stool 16"D (40.64) 24"W (60.96) 16"H (40.64) 26*

7763MR-HR 1017763100 Donnelly Foot Stool 16"D (40.64) 24"W (60.96) 16"H (40.64) with 41"H (104.14) Handrail 39*

7764MR 1012041096 Double Step Stool with Two 41"H (104.14) Handrails 115

7772MR 0927772400 MR Hamper 20"D (50.80) 35"H (88.90) overall ; 2" (5.08) MR Swivel Casters 20*

7772MR-PL 0927772600 MR Hamper 20"D (50.80) 36.5"H (92.71) overall with Plastic Lid; 2" (5.08) MR Swivel Casters 40*

HB-18 9839777201 18" (45.72) diameter Hamper Bags

7792MR-C 0537792002 Five-Leg IV Stand with Two Hooks; 2" (5.08) MR Swivel Casters 35*

7792MR-4C 0537792004 Five-Leg IV Stand with Four Hooks; 2" (5.08) MR Swivel Casters 35*

7741MR-C 0637741200 MR Mayo Stand- 13-3/4"D (34.93) 19"W (48.26) Tray; 2" (5.08) MR Swivel Casters 45*

7766MR 0817766066 MR Kickbucket; 12-1/2 qt. (31.75) Pail; 2" (5.08) MR Swivel Casters 15*

7807MR 0717807066 MR Solution Stand with Shelf 15" (38.10) W 15"L (38.10) 33"H (83.82) 25*

7842MR 0127842002 MR Instrument Table with H-Brace; 2" (5.08) MR Swivel Casters 36"L (91.44) 20"W (50.80) 34"H (86.36) 55

1381MR 3537426350 Push handle for Models 7792MR, 7792MR-4 five-leg IV stands 2

* Items can be shipped via FedEx® Ground delivery service.

FedEx service marks used by permission.

Copyright © 2006 Blickman, Inc.

All shipping weights are estimates only and may be changed without prior notice. Specifications may be improved and dimensions changed without prior notice.

Unless otherwise noted, all products displayed or listed are deemed, MR-’Unsafe,’ in accordance with ASTM Standard F2052-06.

Equipment Solution Planning - ESP Harris Health Smith Clinic - MRI

Specification Coversheet

Item #: INJ21232 Alt ID:

Description: Injector, Contrast Media, MRI Compatible Manufacturer: Medrad, Inc. Model: MRXperion

Basic: Furnish Install: O/V Drawings:

Arch Code: 3 - Minor movable Arch Sig: N

Lead time: 60 days

Physical Requirements Mounting: Mobile Clear. left:

Width: 23.30 in Right:

Height: 71.40 in Top:

Depth: 23.30 in Bottom:

Weight: 95.70 lb Front:

Back: Door swing:

Rough in:

Electrical Requirements Volts: 120 Watts:

Hz: 60 BTU/HR:

Phase: Single Amps

UPS: N Data: Y

Ded. Circuit: N Compressed Air: N

Connection: NEMA 5-15P

Utility Requirements Hot Water: N Cold Water: N

Spec. Water: N Vent: N

Steam: N Gases: N

Drain: N Vacuum: N

Electrical Notes Requires power for monitor in control room and power for scan room unit either in MRI Room or equipment room depending on install type - can be chosen at time of purchase where power supply is located

* This cover sheet is for quick reference only. For full technical specification details please refer to the attached vendor document.

Qty N/E Ord Floor/Room Room Name Department Notes

Operation Manual 1 - 1

S e r i a l n u m b e r s a n d d a t e o f i n s t a l l a t i o n i n f o r m a t i o n m u s t b e s u p p l i e

S e n u m b e r s

Configuration, Planning & Installation Guidelines

Configuration, Planning & Installation Guidelines i

1 Introduction

1.1 Purpose

1.2 Product Overview

1.3 System Components

2 Access and Installation Requirements

2.1 Fiber Optic cables

2.2 Control Room AC Line Cords

2.3 Scan Room AC Line Cords

2.4 Scan Room DC Power Supply Cable

2.5 Control Room Display to Hospital Network Cable

2.6 Alternate Equipment Room Power Supply Installation

3 Specifications

3.1 Display and Pod Specifications

3.1.1 Display and Pod Dimensions

3.1.2 Display and Pod Connections

3.1.3 Display Input Power Requirements

3.1.4 Pod Input Power Requirements

3.2 Injector (Scan Room Unit) Specifications

3.2.1 Injector (Scan Room Unit) Dimensions

3.2.2 Scan Room Unit Power Supply Dimensions

3.2.3 Input Power Requirements

3.3 Penetration Panel…