Lights_User Manual.pdf

Working Modes

On/Off

Constant Lighting Mode Automatically turns on at dusk and remains 50% brightness until dawn or power is off.

Sensor Mode Automatically turns on to full brightness when motion is detected in the range ≤15mtrs and then dim to 30% brightness in 30 seconds of no motion.

Smart Mode Automatically turns on at dusk and remains 50% brightness for 4 hours, then it automatically turns to Sensor Mode.

Please read and follow all instructions to operate.

Save this manual for future reference.

40W / 80W / 120W

Operation Instructions for Single-headed Solar Street Light 40W/80W/120W

Press and hold the on/off button on the lamp for 3-5 seconds. The light will light up for 3 seconds and then turn off, which indicates that the lamp and remote control are successfully activated.

To turn the system completely off, press the on/off button for 3-5 seconds again, and the lamp will flash 3 times and then turn off.

Lamp Button Control Please press the buttons on the lamp to select the preferred working mode below.

The lamp will light up for 3 seconds then off when each button is pressed.

Solar Lighting International, Inc.

STEALTH

LED SOLAR STREET LIGHT

USER MANUAL

One remote control can control all of your lights - Before installing the lights, read this manual, program your lights, and determine the optimal angle to face the light fixture/solar panel, THEN attach the light onto the pole. The optimal angle for the solar panel is your latitude and facing south.

Remote Control Features

Installation

Solar Light * 1pc Remote Control * 1pc User Manual * 1pc

M10x20 Screws * 14pcs M10 Spring Washers * 10pcs M10 Flat Washers * 10pcs

Side Plate of Lamp Pole * 2pcs Holding Bracket of Lamp Pole * 1pc Rotating Device * 2pcs

Please prepare tools and accessories before installation. Each packing includes:

Specification

1. Put the side plates of lamp pole in according to the arrows shown, then fix the side plates to the lamp with flat washers, spring washers and screws.

M10X20 Screws

M10 Flat Washers

M10 Spring Washers

Side Plate of Lamp Pole

Holding Bracket of Lamp Pole Rotating Device

M10 Spring Washers M10 Flat Washers

M10X20 Screws

2. Put the holding bracket of lamp pole into the side plates in the direction shown, and insert the rotating device to the holding bracket and fasten them with flat washer, spring washer and screws.

Product Model

Power

Lumen/LED Type

Battery

Solar Panel

Dimensions(mm)

10-12Hrs to fully charged

40W 80W 120W

STEALTH 40W STEALTH 80W STEALTH 120W

6000 Lumens 12000 Lumens 18000 Lumens (Phillips 5050) (Phillips 5050) (Phillips 5050s)

Li-ion battery, Li-ion battery, Li-ion battery, 22AH,11.1V/244.2Wh 32AH,14.8V/473.6Wh 48AH,14.8V/710.4Wh

Mono-crystalline Mono-crystalline Mono-crystalline 32 Watt 55 Watt 82 Watt

711.0*386.2*244.0 1178.0*386.2*244.0 1616.0*386.2*244.0

Different working mode, different working time, range from 3-6 nights.

140x78°- Type III or Bat-Wing Style Light Distribution

Detection angle: 150° Detection distance:<15Mtrs / 50 Feet

IP65

-20C°- 60C°

-20C°- 60C°

Powder Coat Aluminum+ABS+PC

10' - 15' or 3-5 Meters 15' - 25' or 5-8 Meters 15' - 25' or 5-8 Meters

32’ - 50’ or 10-15Mtrs 50’ - 82’ or 15-25Mtrs 50’ - 82’ or 15-25Mtrs

3 years

Working Time

Charging Time

Beam Angle

PIR Sensor

IP Class

Working Temp

Storage Temp

Housing Material

Installation Height

Installation Spacing

Warranty

Requires 8mm Allen Wrench8mm

1. Before fixing the lamp onto the pole, please press the on/off button on the lamp for 3-5 seconds to activate the lamp and remote control first.

2. Please adjust the solar panel and light panels to the optimal angle, then fix the lamp onto the pole. The optimal angle for the solar panel is your latitude and facing south.

3. Built-in intelligent IC with over-charge, over-discharge, over-temperature protection.

4. If the lamp does not light up after unpacking, it is usually because of insufficient battery power, please charge it for 1-2 days before installing it.

5. It is recommended to install the lamp on a sunny day, so it can charge during the day prior to use without affecting the operation during the night.

6. Please install the lamp in a place with unobstructed full sunlight to ensure it can be charged for

6 hours per day, which gives the lamp a longer working time.

7. As this lamp is photosensitive, it will automatically light up at dusk. Please be aware that it will not light up during day time even it's turned on.

1. The lamp is equipped with an internal battery pack which is replaceable. If you have any need to replace it, please contact the seller for correct new battery pack.

2. If the battery pack is taken out and put back in or replaced with new ones, please re-activate the lamp & remote control by pressing on/off button on the lamp for 3-5 seconds.

3. Please do not disassemble the lamp- this will void your warranty.

4. Please keep the lamp away from fire, oil or flammable materials to avoid any explosion.

5. In order to ensure the lamp in optimal working condition, please clean the solar panel regularly

-We recommend cleaning at least once every six months..

Special Notes

Warning

M10X20 Screws

Pole Mounting (Applicable mounting to lamp pole of 60mm or 2 3/8" O.D.

5. Put the holding bracket onto the lamp pole, and fix the screws on tight.

+90° adjustable

3.Loosen the solar panel screws and adjust the solar panel to the appropriate angle that captures the most sunlight and then tighten the screws. Loosen the light panel screws, adjust the light panel as per demanded lighting directions & area, then tighten the screws.

Infrared Remote Receiver

On/Off

Function Buttons

4. According to the operation instructions, activate the lamp and remote first, then select the demanded working mode.

+40° adjustable Screws B to adjust light panel angle

Screws A to adjust solar panel angle

Requires 8mm Allen Wrench

Sensor Mode Automatically turns on to full brightness when motion is detected in the range ≤15mtrs and then dim to 30% brightness in 30 seconds of no motion.

Operation Instructions for Dual -headed Solar Street Light 80W/120W

Sensor Mode:

Time and Brightness are NOT adjustable.

Press , lamp works as below:

Automatically turns on to full brightness when motion is detected in the range ≤15mtrs and then dims to 30% brightness in 30 seconds if no motion is detected.

Remote Control

Press , lamp will light up for 3 seconds then off, which indicates lamp has tuned on successfully.

Press again, and the lamp will flash 3 times then turn off, this will completely shut the system down.

Constant Lighting Mode:

Time and Brightness are both adjustable.

For example:

1. Press Constant Lighting Mode

2. Press Time 2H

3. Press Brightness 80% The lamp will light up for 3 seconds then off each time the buttons above are pressed, which indicates it's set successfully as below:

Lamp automatically turns on at night and keeps 80% brightness for 2hrs, then it turns to Sensor Mode.

Press and hold the on/off button for 3-5 seconds. Light should light up for 3 seconds then turn off, which indicates that the lamp and the remote control are activated.

To turn off the lamp; press and hold the on/off button for 3-5 seconds to turn off the lamp and deactivate the remote control.

Working Mode Setting :

Once the lamp and remote control are activated, (if at night) the lamp will automatically light up and keep 50% brightness, which is the default working mode.

Please follow below steps to set other working mode by remote control.

Step A: Press , the lamp module on one side will flash, then press or to set demanded working mode (Time and Brightness are both adjustable under Constant Lighting Mode.), the lamp module will light up for 3 seconds then flash when pressing either button, this indicates that the working mode of this side is set successfully.

Step B: Press again, the lamp module on the other side will flash, then repeat the underlined steps as in Step A to set the working mode on the other side.

Step C: Finally press again, the working modes of both sides are set completely.

1. The lamp has a memory function, and will keep current working mode till it's re-set.

2. The standby brightness of Sensor Mode is 30% brightness, which is the default setting.

Special Notes:

Remote Control Distance: ≦1 2Mtrs / 35 Feet