10-PCC White Rock Pottery Project Moving Instructions 2026.pdf

PDF 945 KB Posted

Attached to
NM4 Crossing and Multi-Use Trail Project (CN5101730) And Pinon School Trail (CN5101970)
Solicitation number
IFB27-30
Issued by
Los Alamos County, New Mexico

About this file

This document is a 2026 Install Recommendations report prepared by Pacific Coast Conservation for Los Alamos County Community Services Department regarding the relocation of a large prehistoric pottery recreation from the White Rock area. The project involves moving one significant pottery piece from its current location off NM4 to a predetermined site several yards away due to road and trail realignment associated with the NM4 Crossing and Multi-Use Trail Project. The road contractor will execute the move in June 2026. Current condition assessments from 2025 indicate the pottery replica and its sandstone plaque are in generally good condition, though hairline cracks emanate from the base, streaking appears on the painted surface, and the sandstone base exhibits minor delamination and black spots. The scope of work requires careful documentation through pre- and post-move photography, notification of any new damage, and monitoring of existing cracks during maintenance cycles.

The recommendations emphasize specialized art handling procedures to protect the pottery during relocation. The pot must be supported on all four sides continuously and crated in situ using closed-cell polyethylene foam padding covered with soft Tyvek, with the entire assembly secured using shrink wrap. The rigging must lift the pot from underneath to avoid pressure on the sides that could damage the painted surface. Ideally, an art handling company should perform the crating, with the construction company submitting its moving plan for Pacific Coast Conservation approval. The recommendations specify that lead sheet shims (1/8" to 1/4" thick) replace wood shims beneath the artwork post-installation to prevent deterioration and moisture retention. The new location should be positioned away from vegetation and at sufficient elevation to prevent sand accumulation, with ground cover preferred to minimize environmental changes affecting the artwork.

View the file

Other files

Show all 12

On GovTribe

Work with this file

  • Download the original file
  • Contacts named in this file
  • Similar government files
  • Ask GovTribe AI about this file

Text version

2026 INSTALL RECOMMENDATIONS

February 25, 2026

Client: Chelsea Ashcroft

Sr. Management Analyst Community Services Dept.

Los Alamos County chelsea.ashcraft@lacnm.us

Prepared by: Alison Leard, Director Joy Carlsen, Assistant Conservator Lucinda Linderman, Conservator Pacific Coast Conservation 310- 383-4710

Purpose:

The purpose of this document is to make recommendations for moving one of the large pottery recreations in the Los Alamos County art collection. The work will be completed by a city contractor in June of 2026.

Background:

One of the large pieces (the prehistoric pot off NM4) will need to be relocated due to road/trail realignment. The contractor for the road project will move it to a predetermined location just a few yards away. Construction is scheduled to begin in June 2026.

Condition notes 2025:

The sculpture and plaque are in good condition overall. There was a light layer of atmospheric, insect, and plant debris on the surface of the pottery replica. One plant on the northwest side of the sculpture was touching the artwork and needed to be cut back. Several instances of bird droppings were present on the surface. Hairline cracks were present throughout, mainly emanating from the base. None of these were wide enough to require intervention but will continue to be monitored for changes during each maintenance cycle. Streaking was noted on the painted surface and did not reduce during washing. The sandstone base had small black spots on the surface, which did not reduce during washing. Further testing will be done during future maintenance. Thin layers of the sandstone had delaminated and were cleared during maintenance to prevent water from being held in between the surfaces of the stone.

Recommendations:

For the move – We suggest taking multiple photographs of the pot before and after the move, noting current cracks, and documenting new cracks if they occur. Please notify PCC of any new damage so we can properly prepare for the 2026 maintenance cycle.

Since the art is susceptible to cracking, the pot should be supported on all sides, or a minimum of 4 sides, at all times. The artwork should have a crate built around it in situ. The crate should have closed cell polyethylene foam in-between the pot and crate. The foam should be covered with soft Tyvek. The pot should also be covered in clean, soft Tyvek, secured with shrink wrap around the Tyvek. The mailto:chelsea.ashcraft@lacnm.us weight of the pot should be evenly distributed as much as possible within the crate. This is to prevent any rubbing between the crate and the pot so that the paint is not rubbed off.

The crate and pot should be rigged in such a way that the pot is lifted from underneath so that no pressure is placed on the sides of the pot.

Ideally, an art handling company should crate the artwork for the move.

The construction company should provide a document stating how they plan on moving the artwork for PCC to review.

Another option for secure crating. Wood 2x4’s could be placed under the pot. There is an image where the pot is leaned to one side during installation, it could be leaned to get the wood under it. The body of the vessel should be wrapped as noted above. An open crate could then be built around the sculpture. To even out the pressure around the crate and to pad between the wood and the object, clear plastic bags could be placed in gaps between the crate and the sculpture and then filled with expanding foam (holes may need to be placed in the bags so that the foam can react with the air.

The sandstone plinth is prone to delamination so chips may fall off the surface. Padding and proper support is also required during the move. Also, ensure the area beneath the pot is secure before reinstalling. If the area has loose or fracturing sections, they should be removed from the plinth before installation. Do not use wood blocks, boards, or wood shims beneath the artwork, as they will deteriorate and need to be removed at a later date. Lead sheet shims (1/8” to ¼" thick) should be used to shim the pottery all the way around after install. The lead is soft and will allow the pot to settle once installed and the lead will keep moisture from sitting next to the surface of the pot.

If water or debris is found inside the artwork, it should be removed during the process.

New location – The new location should be away from vegetation (large bushes or trees) to avoid future growth from abrading the surface.

If the new location is on a hill surrounded by sand, ensure the top of the plinth is high enough that the sand will not run down the hill and cover the plinth in a storm. Having ground cover of some kind is preferred so changes in the surrounding ground do not become a future problem.

Crack in the base of the pot Delaminating section of the sandstone

Crack down the side Cracks around the base

Provided by Los Alamos County – Location of current and new trail and artwork

Provided by Los Alamos County – Location of current and new trail and artwork

File details come from the government source that posted it. Updated .