USCGC HALIBUT - Dry Dock Repairs

Added: Aug 28, 2014 5:15 pm The United States Coast Guard, Surface Forces Logistics Center, Oakland, CA intends to issue a Commercial Request for Quote (RFQ) for dry dock and repairs to the CGC HALIBUT (WPB-87340) an 87-Foot Coastal Patrol Boat Cutter. The NAICS Code is 336611.

The Coast Guard intends to conduct the procurement in accordance with Federal Acquisition Regulation (FAR) Part 12, Acquisition of Commercial Items, and FAR Part 13.5 Test Program. The simplified acquisition will be issued as a Total Small Business Set-Aside. Request for Quotes (RFQ) will be issued on or about September 05, 2014.

The acquisition is to perform dry dock and repairs to the CGC HALIBUT. The vessel is geographically restricted to a facility located in the United States West Coast San Francisco Bay and South. The Period of Performance for CGC HALIBUT is fifty-eight (58) calendar days from 12 November 2014 through 09 January 2015. All work will be performed at the contractor's facility within the geographical restriction as stated above.

The solicitation will be issued electronically via the Federal Business Opportunity web page at http://www.fedbizopps.gov. It is incumbent upon contractors to monitor the FEDBIZOPS web page for the RFQ release and all subsequent amendments. Hard copies of the specification and solicitation will not be issued.

The scope of the acquisition is for the overhauling, renewing and repairing of various items aboard the CGC HALIBUT. This work may include, but is not limited to:

Ultrasonic Thickness Measurements, Perform (D)
Ultrasonic Thickness Measurements, Perform (O)
Hull Plating (U/W Body), Inspect
Bilge Surfaces (Lazarette), Preserve ("100%")
Dirty Oil Tank, Clean and Inspect (D)
Tanks (MP Fuel Stowage and Overflow), Clean and Inspect (D)
Voids (Non-Accessible), Leak Test
Tanks (Lube Oil), Inspect
Oily Water Tank, Clean and Inspect (D)
Voids (Non-Accessible), Internal Surfaces, Preserve
Depth Sounder, Capastic Fairing, Renew (O)
Main Diesel Engines, Port and Starboard, Renew
Main Engine/Reduction Gear, Realign (O)
Propulsion Shafts, Remove, Inspect, and Reinstall
Propulsion Shaft, Repair (O)
Propulsion Shaft, Straighten (O)
Intermediate Water-Lubricated Propulsion Shaft Bearing, Renew (O)
Aft Water-Lubricated Propulsion Shaft Bearing, Renew (O)
Intermediate Bearing Carrier, Renew (O)
Stern Tubes, Interior Surfaces, Preserve 100% (O)
Stern Tubes, Interior Surfaces, Repair (O)
Propellers, Remove, Inspect, and Reinstall
Speed Log, Skin Valve Assembly, Clean and Inspect
HVAC System, Repair
Sea Water System (Sea Valves, Strainers, Piping), Clean, Inspect and Repair (D)
Rudder Assemblies, Remove, Inspect and Reinstall
RHIB Notch Skid Pads, Inspect (D)
RHIB Notch Skid Pad Studs, Renew (O)
Stern Launch Door, Remove, Inspect and Reinstall (D)
Grey Water Holding Tank(s), Clean and Inspect (D)
Sewage Holding Tank(s), Clean and Inspect (D)
Grey Water Piping, Clean and Flush (D)
Sewage Piping, Clean and Flush
U/W Body, Preserve (100%)
Main Mast, Preserve, 100%
Superstructure, Preserve "100%"
Cathodic Protection / Zinc Anodes, Renew «ASSET»
Drydocking
Temporary Services, Provide - Cutter
Sea Trial Performance, Support, Provide
Ventilation Systems, Commercial Cleaning
Vent Ducts, Renew
Install Stainless Steel Hull Inserts and Renew BMDE Concentric Rings.(D)
DC Locker Deck, Preserve
Insulation, Renew
Interior Deck Covering System, Reseal
Sewage Piping, Repair
Stern Gate Hydraulic Rams, Repair
Appendages (U/W), Leak Test
Appendages (U/W) - Internal, Preserve
Tanks (MP Fuel Stowage and Overflow), Clean and Inspect (D)
Tanks (MP Fuel Service), Clean and Inspect (D)
Aft Bearing Carrier, Renew (O)

If two companies are planning to conduct business as a Joint Venture or any other type of teaming agreement they shall provide past performance on projects of similar scope that they have performed together as a Joint Venture, if available. Providing individual past performance documentation from each company on separate projects where the two did not work together may be considered less relevant.

A CD-ROM containing all applicable drawings will be sent via U.S. mail, if requested. Send all requests to Bernie.c.caguiat@uscg.mil. The CD-ROM sets are available of all cutters and will be free of charge to contractors upon request. The CD-ROM(s) contain WINDOWS compliant raster/vector formats (e.g.*.DWF, etc).

Proposals are due on or about October 06, 2014 at 10:00 a.m. Pacific Time and may be sent via:

Email: Bernie.c.caguiat@uscg.mil or mailed to

USCG Surface Forces Logistics Center
ATTN: Bernie Caguiat
1301 Clay Street, Suite 800N
Oakland, CA 94612