Self-Regulating Heaters for Satellites

Closed Solicitation Posted

Solicitation number
SF24B-T008
Agency
Responses due
Set-aside
Total Small Business

Opportunity facts

More information

Notice details come from DoD SBIR/STTR (DSIP). Updated .

About this opportunity

The Department of the Air Force Materiel Command seeks Phase I STTR proposals for self-regulating satellite heaters under DoD topic SF24B-T008, with proposals due June 12, 2024, which precedes the current date of November 17, 2026. The Set Aside is Total Small Business.

Research and development must be performed in the United States unless the DAF approves specific exceptions in writing. The technology is ITAR-controlled, and any proposed foreign national participation must be disclosed under ITAR (22 CFR Parts 120-130) and EAR (15 CFR Parts 730-774). The notice identifies no place of performance beyond this requirement.

The technical objective is a positive temperature coefficient heater for satellites in any earth orbit, in a thin-film, adhesively applied polyimide form factor installable on orthogonal bend axes (1/8" and 3" bend radius). Required specifications include setpoint tuning from -5C to 20C, a 30:1 threshold and 100:1 objective resistance turndown ratio, operation at any voltage from 12 to 100 VDC, and 1 to 10 W/in2 heat flux at full ON. Heaters must survive 5 years in LEO, 10 years in MEO, or 15 years in GEO, including vacuum, ionizing radiation (40 mils aluminum shielding threshold, no additional shielding objective), and thermal cycling (60,000 LEO, 15,000 MEO, or 6,000 GEO cycles between -5C and 40C, plus up to 10 cycles from -40C to 70C). Manufacturing must be scalable by screen printing with minimal installation touch labor.

Phase I requires feasibility demonstration through modeling, analysis, and prototype testing, with a maximum value of $180,000 and a 6-month performance period. Phase II requires environmental testing and delivery of 10 functional tested heaters, and is restricted to Phase I awardees. Phase III covers flight qualification and transition to at least one satellite integrator. The attached Phase I instructions set subcontracting minimums of 40% small business concern performance and 30% research institution effort. Proposals are submitted through DSIP in six volumes, with a Technical Volume capped at 20 pages. Evaluation takes approximately 90 days, and non-selected offerors receive automated feedback. The point of contact is Jon Allison, AFRL/RVSV, 505-853-3080, jonathan.allison.1@spaceforce.mil.

Notice text

DoD STTR topic SF24B-T008

Component: USAF

Command: AFMC

Phase: STTR Phase I

Technology Areas: Space Platforms

Focus Areas: Space Technology

Keywords: Thermal Control; Thermal Management; Satellites; Heaters; Self-Regulating Heaters

ITAR: Yes

Objective:

The objective of this topic is to develop and commercialize self-regulating (positive temperature coefficient, PTC) heaters for use on

satellites in any earth orbit.

Description:

Self-regulating heaters are heaters with a designed-in temperature setpoint that exists as a property of the resistor material. They are ‘smart’ heaters, automatically and independently warming each region of the heater circuit to the designed setpoint without a temperature sensor. The electrical resistance of the heater material jumps substantially at the setpoint, inhibiting electric flow and production of heat above the setpoint temperature. Self-regulating heaters are in use in the petrochemical and automotive industries for pipe freeze protection and seat warmers. The space industry needs self-regulating heaters for propellant system heaters where allowable temperature ranges are tight and thermal environments vary in both time and space. Conventional solutions to propellant system thermal control are resource intensive, requiring much engineering design and touch labor as well as much hardware and burdening the flight computer to control the circuits. Self-regulating heaters reduce all of these resource demands. Self-regulating heaters can also provide similar benefits for other satellite heaters such as those for batteries, mechanisms, and antennas.

Existing self-regulating heaters are not suited for space applications for several reasons:

1) the form factor is too large and inflexible: existing self-regulating heaters are a stiff cable while satellite self-regulating heaters must be a thin-film heater such as adhesively-applied polyimide heaters commonly used on satellites. Additionally, these heaters must be suitable to install on two orthogonal bend axes: a 1/8” bend radius and a 3” bend radius, 2) existing self-regulating heaters provide their resistance transition via a melt expansion process to break the percolating path; this means that existing self-regulating heaters cannot be exposed to temperatures greater than their setpoint temperature, 3) Existing self-regulating heaters are not designed to handle the space environment; specifically: vacuum, ionizing radiation, and wide thermal cycles.

This topic solicits proposals to develop and commercialize self-regulating heaters for space applications that address these aforementioned insufficiencies of existing self-regulating heaters. Additionally, the materials design must be capable of tuning during manufacturing of the material for setpoint temperatures between -5 and 20 C. A 30:1 (threshold) and 100:1 (objective) turndown ratio between the electrical resistances above and below the setpoint temperature must be achieved. The technology must be capable of yielding designs operating with any voltage between 12 and 100 VDC, and must be capable of producing designs yielding 1 to 10 W/in2 heat flux at the fully ON condition. Capable to withstand exposure to environments in all of the following orbits: 5 years in low earth orbit (LEO), 10 years in middle earth orbit (MEO), or 15 years in geosynchronous earth orbit (GEO) including vacuum, ionizing radiation, and thermal cycling. Radiation environments should assume the technology receives 40 mils of spacecraft Aluminum shielding (threshold) or no additional shielding (objective); radiation shields incorporated in the heater will be considered but radiation-hardened heater materials are strongly preferred. Thermal cycles between -5 and 40 C, with LEO 60k cycles, MEO 15k cycles, and GEO 6k cycles. Also survive up to 10 thermal cycles from -40 to 70 C. The material should always remain a solid. The manufacturing process should be scalable, e.g. screen printing techniques; the installation process should minimize touch labor. Proposers must demonstrate a strong intent and capability to commercialize the technology. Proposers are strongly encouraged to form teams with manufacturing partners and systems integrators for technology transition.

Phase I:

Awardee(s) will demonstrate by modeling and analysis and/or test the feasibility of the concept to meet all requirements. Develop and test the performance of prototype hardware.

Phase II:

Awardee(s) will further develop the prototype to increase performance, manufacturability and scalability of the hardware. Awardee(s) will test environmental capability of the hardware. The culmination of the Phase II effort shall include the hardware delivery of 10 functional, tested self-regulating heaters demonstrating a variety of sizes and mounting configurations.

Phase III:

Awardee(s) can expect to develop, produce, and bring to market a fully flight qualified self-regulating heater product line; transition the technology to at least one satellite integrator.

Files

File Type Posted
SF24B-T008.pdf PDF
AF_STTR_24B_v3.pdf PDF

Similar open opportunities

On GovTribe

Work this opportunity

  • Track it in your pipeline
  • Find teaming partners
  • Similar opportunities
  • Ask GovTribe AI about this opportunity

GovTribe for Federal Contractors