Y26-716_Drawings.pdf

PDF 5 MB Posted Dec 22, 2025

Attached to: Administration Center Redistricting Renovation (Chambers Dais)
Solicitation number: Y26-716
Issued by: Orange County, Orlando City, Florida

About this file

Written by GovTribe AI · Apr 13, 2026

This file comprises architectural and engineering drawings for the Administration Center Redistricting Renovation (Chambers Dais) project in Orange County, Florida, prepared by Rhodes+Brito Architects, Kaleidoscope Interior Design, and Bobes Associates. The project involves a Level 1 alteration to the dais bench in the BCC Chambers Room (Room 104) on the first floor of the Orange County Administration Building located at 400 E South Street, Orlando, Florida. The renovation accommodates two new county commissioners through reconfiguration of the existing dais bench with new finishes, including solid surface work surfaces (Wilsonart Morning Ice), new LED lighting strips, above-counter power receptacles with USB and USB-C connections, new presentation monitors, and undercounter wireless duress alarm call buttons. The design team includes mechanical, electrical, fire protection, and technology specialists. The project requires coordination with multiple building systems including the existing Lenel OnGuard access control system, new discussion system controllers with integrated speakers and gooseneck microphones at each commissioner station, and new VGA distribution amplifiers for monitor signal distribution. Sealed bids are due electronically through the OpenGov e-Procurement Platform by February 10, 2026, at 4:00 p.m. EST, with a non-mandatory pre-bid meeting scheduled for January 14, 2026, at 1:00 p.m. Questions must be submitted by January 26, 2026, at 5:00 p.m. EST.

The estimated project cost is $200,000.00. Bidders must be registered with E-Verify, maintain a drug-free workplace, and provide at least three references for similar commercial construction projects completed within the last ten years. A bid bond of not less than 10 percent of the total estimated contract amount is required, along with payment and performance bonds upon award. The county will retain 5 percent retainage from progress payments. All work must comply with the Florida Building Code (8th Edition, 2023), the 2020 National Electrical Code, City of Orlando Building Department requirements, and all applicable local, county, and state codes and standards. The contractor is responsible for temporary power and lighting during construction and must provide comprehensive warranty coverage including one-year full warranty on all work and materials, with extended warranties for structured cabling (25 years) and emergency lighting batteries. The project requires coordination with Orange County Information Systems and Services (ISS) and Enterprise Security, with specific technology standards including Siemon certified cabling, Audio-Technica discussion systems, and integration with the existing access control infrastructure. The contract will be awarded to the lowest responsive and responsible bidder.

View the file

Other files

File	Type	Posted
Administration_Center_Redistricting_Renovation_(Chambers_Dais)_(Addendum_#3_Revision).pdf	PDF	Feb 6, 2026
Administration_Center_Redistricting_Renovation_(Chambers_Dais).pdf	PDF	Jan 6, 2026
Orange_County_ISS_Infrastructure_Standards_and_Specification.pdf	PDF	Dec 22, 2025
Y26-716_Specifications.pdf	PDF	Dec 22, 2025
Orange_County_ISS_Infrastructure_Standards_and_Specification.pdf	PDF	Dec 22, 2025
Y26-716_Specifications.pdf	PDF	Dec 22, 2025
Standards_and_Guidelines_Access_Control_Revised.pdf	PDF	Dec 22, 2025
Standards_and_Guidelines_Access_Control_Revised.pdf	PDF	Dec 22, 2025
Y26-716_Drawings.pdf	PDF	Dec 22, 2025

On GovTribe

Work with this file

Download the original file
Contacts named in this file
Similar government files
Ask GovTribe AI about this file

Try for free Login

Text version

The file's text, extracted by GovTribe without its formatting.

PROJECT LOCATION

THIS PROJECT IS THE RENOVATION OF THE

DAIS BENCH IN THE BCC CHAMBERS ROOM

ON THE FIRST FLOOR OF THE ORANGE

COUNTY ADMINSTRATION BUILDING. THE

BENCH WILL BE RECONFIGURED TO

ACCOMODATE THE TWO NEW COUNTY

COMMISSIONERS AND WILL RECEIVE NEW

FINISHES. THIS IS A LEVEL 1 ALTERATION

TO FINISHES ONLY.

PROJECT SCOPE

VICINITY MAP

PROJECT DESIGN TEAM

RHODES+BRITO ARCHITECTS 605 E.

ROBINSON ST, SUITE 750

ORLANDO, FL 32801

PH. (407) 648-7288

CONTACT: LORI GODBOLD, AIA, NCARB

ARCHITECTURE

KALEIDOSCOPE INTERIOR DESIGN

SUITE

CITY, FL 12345

PH: (407) 702-8208

CONTACT: MANDY WANNEN, LEED SP, EDAC, ALEP

INTERIORS

BOBES ASSOCIATES

150 CIRCLE DRIVE

MAITLAND, FL 32751

PH: (407) 628-0882

CONTACT: GUS BOBES JR, P.E.

FIRE

PROTECTION

A C CT T SEH IR

AR0014284

BOBES ASSOCIATES

150 CIRCLE DRIVE

MAITLAND, FL 32751

PH: (407) 628-0882

CONTACT: GUS BOBES JR, P.E.

MECHANICAL

BOBES ASSOCIATES

150 CIRCLE DRIVE

MAITLAND, FL 32751

PH: (407) 628-0882

CONTACT: GUS BOBES JR, P.E.

ELECTRICAL

BOBES ASSOCIATES

150 CIRCLE DRIVE

MAITLAND, FL 32751

PH: (407) 628-0882

CONTACT: GUS BOBES JR, P.E.

TECHNOLOGY

NICOLE H. WILSON CHRISTINE MOORE

District 1 Commissioner District 2 Commissioner

MAYRA URIBE MARIBEL GOMEZ CORDERO

District 3 Commissioner District 4 Commissioner

KELLY MARTINEZ SEMRAD MICHAEL "MIKE" SCOTT

District 5 Commissioner District 6 Commissioner

JERRY L. DEMINGS

ORANGE COUNTY MAYOR

BOARD OF COUNTY COMMISSIONERS

ORANGE COUNTY ADMINISTRATION

BUILDING BCC CHAMBERS DAIS BENCH

RENOVATION

Permit Documents

11/20/2025

ORANGE COUNTY GOVERNMENT

400 EAST SOUTH STREET, SUITE 500

ORLANDO, FL 32801

G000

INDEX OF DRAWINGS

G000 COVER, INDEX

ID101 DAIS MILLWORK

E001 ELECTRICAL GENERAL NOTES

E101 POWER+LIGHTING+SYSTEM DEMOLITION PLAN

E102 POWER+LIGHTING+SYSTEMS RENOVATION PLAN

DATE SUBMISSION / REVISION NO.

r h o d e s + b r i t o A R C H I T E C T S

A101

A711

MATERIALS LEGEND

DRAWING FORMAT

DIMENSIONING SHEET NUMBERING

100 SF

A101

A711A scale:

drawn:

check:

date:

project no: 2001.001

01.01.01 date

Client Logo and

Project Title

ALL

REPRODUCTION

AND

INTELLECTUAL

PROPERTY

RIGHTS

RESERVED

CLIENT LOGO

HERE

1 2 3 4 5 6 7 8 9 10

19.02

TYP

A1 A3

A5 A7 A9

EACH SHEET IS DIVIDED INTO A GRID. AN ALPHA-NUMERIC GRID COORDINATE SYSTEM IS USED TO ORGANIZE THE DRAWING TITLES

DRAWING TITLES ARE NUMBERED ACCORDING TO ITS LOCATION ON THE GRID. THE LOWER LEFT HAND CORNER GRID OF THE

DRAWING IS USED AS THE IDENTIFICATION NUMBER (SEE DIAGRAM).

COLUMN CENTERLINE

PARTITIONS ARE DIMENSIONED TO FACE OF STUDS, FACE OF CMU AND FACE OF

BLOCK UNLESS INDICATED OTHERWISE

DIMENSIONS ARE INDICATED ON DRAWINGS, DO NOT SCALE DRAWINGS

PARTITION

KEYNOTE

REFERENCE

ELEVATION

REFERENCE

REVISION

IDENTIFICATION

PARTITION TYPE

IDENTIFICATION

WINDOW TYPE

REVISION NUMBER

(REFER TO TITLE

BLOCK)

TARGET ELEVATION

TARGET DESCRIPTION

WINDOW DESIGNATION

(REFER TO WINDOW

SCHEDULE)

REFERENCE NUMBER

PARTITION TYPE

(REFER TO PARTITION

TYPE DETAILS)A

GRAPHIC

SCALE

INDICATES FEET

WHEN A ROOM/BUILDING/OBJECT CENTERLINE IS INDICATED, ONLY ONE SIDE OF

ELEMENT MAY BE DIMENSIONED

PARTITIONS WITH FINISH FACE FLUSH WITH FINISH FACE OF COLUMN WILL NOT BE

DRAWN ON SMALL SCALE PLANS BUT WILL BE DRAWN ACCORDINGLY ON LARGER

SCALE DRAWINGS.

COLUMN CENTERLINE

PARTITION FINISH FACE ON COLUMN OR GRID LINE WILL NOT BE DIMENSIONED ON

SMALL SCALE PLANS BUT WILL BE DRAWN ACCORDINGLY ON LARGER SCALE

DRAWINGS.

PARTITIONS CENTERED ON COLUMNS OR GRID LINES WILL NOT BE DIMENSIONED ON

SMALL SCALE PLANS BUT WILL BE DRAWN ACCORDINGLY ON LARGER SCALE

DRAWINGS.

PARTITION

B. AS DIMENSIONED

COLUMN CENTERLINE

PARTITION

DOOR LOCATION

DOORS ARE LOCATED BY ONE OF THE FOLLOWING:

A. ONE JAMB FACE LOCATED BY A PARTITION AT RIGHT ANGLE.

PARTITION

DOOR

SINGLE INTERIOR

ELEVATION

REFERENCE

RESTROOM

ACCESSORY

IDENTIFICATION

DOOR NUMBER

SPOT

ELEVATION

REFERENCE

TRUE

NORTH ARROWDOOR NUMBER

(SEE DOOR SCHEDULE)

TARGET ELEVATION

ACCESSORY TYPE

(REFER TO RESTROOM

ACCESSORY SCHEDULE)A

ELEVATION DETAIL NUMBER

ELEVATION ORIENTATION

SHEET NUMBER ON WHICH

ELEVATION OCCURS

ROOM AREA

WALL SECTION

OR BUILDING

SECTION

REFERENCE

ROOM NUMBER

SHEET NUMBER ON

WHICH SECTION OCCURS

SECTION ORIENTATION

SECTION DETAIL NUMBER

ROOM NAME

COLUMN

IDENTIFICATION

CALLOUT DETAIL

REFERENCE

A501

COLUMN CENTERLINE

DRAWING ON WHICH

DETAIL OCCURS

DETAIL NUMBER

REVISION SYMBOLS

REVISION AREA

REVISION DELTA

SUBCATEGORY

SHEET NUMBER

ITEM

CATEGORY

CHAMFER

CABINET

MANHOLEMH

INVERTINV

FRP FIBERGLASS REINFORCED

PLASTICEJ EXPANSION JOINT

GALVANIZED STEEL SHEET

EQUIP

EXT

EXP

EST

ESC

EWC

ENGR

ENCL

EMER

ELEV

ELEC

EQUIPMENT

EXPANDED(EXPANSION)

ELECTRIC WATER COOLER

EXTERIOR

EXISTING

ESTIMATE

ESCALATOR

ELECTRICAL POWERBOARD

ENGINEER

EQUAL

ENCLOSE(URE)

EMERGENCY

ELEVATOR

ELEVATION

ELECTRICAL

GKT GASKET(ED)

GYP

GWB

GYPBD

GLAM

GSS

GYPSUM WALL BOARD

GYPSUM BOARD

GLUE LAMINATED

GALVANIZED PIPE

GYPSUM

GLASS

GEN'L

GALV

FURN

FUT

FUR

FTG

FRT

GALVANIZED IRON

GENERAL CONTRACTOR

GALVANIZED

GAUGE

GENERAL

GRADE

GRAB BAR

FURNITURE/FURNISHINGS

FIRE-RETARDANT

FOOT

FUTURE

FURRING

FULL SIZE

FOOTING

KIT

JST

IPS

JOINT

KITCHEN

KNOCKOUT

JANITOR CLOSET

JUNCTION BOX

JOINT FILLER

IRON PIPE SIZE

JOIST

MIR

MISC

MIN

MTD

MASONRY OPENING

MIRROR

MISCELLANEOUS

MILLIMETER

MINIMUM

METAL THRESHOLD

MOUNTED

FIRE-RESISTANT COATING

FIRE EXTINGUISHER CABINET

FINISHED FLOOR ELEVATION

EXTERIOR INSULATION & FINISH

SYSTEM

DISP DISPENSER

EIFS

DWR

DWG

DRB

DIV DR

DTL

EXPANSION BOLT

EAST

EACH

DRAWER

DIVISION DOOR

DAMP PROOFING

DOOR

DOWN

DRAWING

DRAIN BOARD

DOWN SPOUT

DETAIL

DEAD LOAD

DEPT

DBL

DIM

DIA

DEP

DEMO

DRINKING FOUNTAIN

DEMOLISH, DEMOLITION

DEPARTMENT

DOUBLE

DIMENSION

DOUBLE HUNG

DIAGONAL

DEPRESSED

FF FACTORY FINISH

FND

FPL

FRC

FOS

FOF

FOM

FOC

FLUOR

FJT

FLR

FLEX

FLG

FFE

FIN

FGL

FRAME(D)(ING)

FOUNDATION

FLOOR PLATE

FACE OF STUDS

FACE OF FINISH

FACE OF MASONRY

FACE OF CONCRETE

FIREPROOF

FLUORESCENT

FIRE HYDRANT

FLUSH JOINT

FIBERGLASS

FLOOR

FLEXIBLE

FLASHING

FINISH(ED)

FBO

FCO

FEC

FAS

FURNISHED BY OTHERS

FLOOR CLEAN OUT

FIRE EXTINGUISHER

FIRE ALARM

FASTEN, FASTENER

FLOOR DRAIN

FACE BRICK

INSULATED BY CONTRACTOR

HEATING/VENTILATING/AIR

CONDITIONING

HP HIGH POINT

INCL

INT

IBC

INFO

INSUL

HWH

HRDW

HWD

HD HT

HTG

HVAC

HOT

WATER

HEATER

INCLUDE(D)(ING)

INFORMATION

INSIDE DIAMETER

INSULATION

INTERIOR

HARDWOOD

HEAD HEIGHT

HOUR

HARDWARE

HEATING

HEIGHT

HOR

HBD

HJT

HDR

HOLLOW METAL

HORIZONTAL

HARDBOARD

HEAD JOINT

HEAVY DUTY

HOLLOW CORE

HOSE BIBB

HEADER

LUMP SUMLS

MED

MEMB

MECH

MAS

MAT'L

MAX

MEP

MTL

MFR

LVR

LVL

MATERIAL

MECHANICAL

MEDIUM

MEMBRANE

MAXIMUM

MANUFACTURER

METAL

MASONRY

LOUVER

METER

LIGHT

LAV

LAM

LBL

LAB

LAVATORY

LAMINATE

LINEAR FOOT

LEFT HAND

LABORATORY

LAG BOLT

LIVE LOAD

LABEL

WROUGHT IRON

VINYL ASBESTOS TILE

WELDED WIRE FABRIC

WALL TO WALL

UNDERWRITERS

LABORATORY

UNLESS NOTED OTHERWISE

VAPOR BARRIER

VINYL COMPOSITION TILE

WHEEL BUMPER

WATER REPELLENT

WATERPROOFING

WATER CLOSET

WHB

STANDARDSTD

ROOMRM

PRE CAST CONCRETEPCC

ROUGH OPENING

REVERSE(SIDE)

RIGHT OF WAY

RAIN WATER CONDUCTOR

POLYVINYL CHLORIDE

POUNDS PER CUBIC FOOT

POUNDS PER LINEAL FOOT

POUNDS PER SQUARE FOOT

POINT/PRESSURE TREATED

POUNDS PER SQUARE INCH

PROPERTY LINE/PLATE

PREFABRICATE(D)

PRE FINISHED

PLASTIC LAMINATE

PAIR/PROPOSAL REQUEST

PRELIMINARYPRELIM

PVC

PSF

PSI

PRF

PTN

PVMT

PERFORMED

PARTITION

PAVEMENT

PLF

PLYWD

PREFAB

PNT

POL

PLBG

PNL

PNTD

PLYWOOD

PAINT

POLISHED

PLUMBING

PANEL

PAINTED

PCF

PERIM

PFN

PLAM

PLAS

PLATE GLASS

PERIMETER

PHASE

PANEL JOINT

PLASTER

ROW

RVS

RWC

TOP OF MASONRY

TONGUE AND GROOVE

TOILET PARTITION

TOILET PAPER DISPENSER

THRES THRESHOLD

TR TRANSOM

TYPICAL

TELEVISION

TYP

TOLERANCE

TOP OF

TOP OF STEEL

TOP OF WALL

TOILET

TOL

TOM

TOS

TOW

TLT

TPTN

TPD

TOWEL BAR

TREAD

THICK(NESS)

TEMPORARY

TERRAZZO

TELEPHONE

T&G

THK

TEMP

TER

TEL

SYSTEM

SYNTHETIC

SYMMETRY(ICAL)

SUSPENDED

STRUCTURAL

STORAGE

STEEL

SYS

SYN

SYM

SUS

STR

STOR

STL

WTW

WWF

WSCT

WIN

WTH

WAINSCOT

WITHOUT

WIRED MESH

WINDOW

WIDTH

WATER STOP

RUBBER BASE

REQUEST FOR INFO

ROOF HATCH

REFLECTED CEILING PLAN

REVISION(S),(D)

REFLECT(ED),(ING)

REFRIGERATOR

RAIN LEADER

REINFORCE(D),(ING)

QUARRY TILE

VERTICAL DATUM

NATIONAL GEODETIC

NOT APPLICABLE

NOT IN CONTRACT

OUTSIDE DIAMETER

NOT TO SCALE

OVERFLOW ROOF DRAIN

OPPOSITE HAND

OPP

ORD

PRE CAST

OVERALL

OPPOSITE

OUTSIDE

OFC

OPG

OH/OPH

ON CENTER

OFFICE

OVERHEAD

OPENING

NGVD

NIC

NOM

NTS

NORTH

NUMBER

NOMINAL

RADIUSRAD

RFI

RFH

RFG

REV

RES

RET

RFL

ROOFING

RESILIENT

RETURN

RIGHT HAND

REQ'D

RCP

REM

REF

REFR

REG

REINF

REQUIRED

ROOF DRAIN

REMOVE

REFERENCE

QTR

RETURN AIR

RISER

QUARTER

SLAB ON GRADE

STAINLESS STEEL

SPECIFICATION(S)

SHELVINGSH

STATION

SQUARE YARD

SQUARE INCH

SQUARE

SPECIAL

SPEAKER

SPACER

STA

SQ/YD

SQ/IN

SPEC

SPL

SPK

SPCR

SEALER

STEEL JOIST

SHELVING

SOUND PROOF

SLEEVE

SIMILAR

SHEET

SHEATHING

SOG

SLR

SHELV

SIM

SHT

SHTH

SQUARE FOOT

SOUTH

STORM DRAIN

SOLID CORE

SHEET GLASS

SECTION

SCHEDULE

SAFETY GLASS

SECT

SCHED

SFGL

WITH

WALL HUNG

WOOD BASE

WOOD

WIRED GLASS

WEST

VAT

VEST

VCT

VAR

VERT

VESTIBULE

VARNISH

VERTICAL

UNF

UNO

UNFINISHED

URINAL

UNDERCUT

OPCI OWNER PROVIDED

CONTRACTOR INSTALLED

OPOI OWNER PROVIDED

OWNER INSTALLED

CPCI CONTRACTOR PROVIDED

CONTRACTOR INSTALLED

RECEP RECEPTIONIST

SECRETARYSECR

SECURITYSECU

AHJ AUTHORITY HAVING JURISDICTION

VOL VOLUME

FV FIELD VERIFIED

UNO

4" TYP

SYMBOL LEGEND

ROOM

NAMEROOM

IDENTIFICATION

A711

MULTIPLE

INTERIOR

ELEVATION

REFERENCE

A2A4

ELEVATION DETAIL NUMBER

ELEVATION ORIENTATION

SHEET NUMBER ON WHICH

ELEVATION OCCURS

FIRST FLOOR

100' - 0"

SPECIALITY

EQUIPMENT

IDENTIFICATION

EQUIPMENT TYPE

(REFER TO EQUIPMENT

SCHEDULE)A

02 4 8134 no.revision

G - General

ID - Interior Design

FS - Food Service

FP - Fire Protection

T - Technology

SCALE:

DATE:

DRAWN BY:

CHECK BY:

PROJECT NUMBER:

1 2 3 4 5 6 7 8 9 10

ALL REPRODUCTION AND INTELLECTUAL

PROPERTY RIGHTS RESERVED ©

Seal

Consultants

Client

A C CT T SEH IR

605 E. ROBINSON STREET, SUITE 750

ORLANDO, FL 32801

AR0014284

www.rbarchitects.com 407.648.7288

12" = 1'-0"

G001

GENERAL

INFORMATION

05/21/2025

18019

ORANGE COUNTY

ADMINISTRATION

BUILDING BCC

CHAMBERS DAIS

BENCH RENOVATION

ORANGE COUNTY

GOVERNMENT

Permit Documents

GENERAL

REV. NO. SHEET NAME

G000 COVER SHEET

G001 GENERAL INFORMATION

Grand total: 2

ELECTRICAL

REV. NO. SHEET NAME

E001 ELECTRICAL GENERAL NOTES

E101 POWER+LIGHTING+SYSTEMS DEMOLITION PLAN

E102 POWER+LIGHTING+SYSTEMS RENOVATION PLAN

E201 SYSTEMS DETAILS

Grand total: 4

INTERIOR DESIGN

REV. NO. SHEET NAME

ID101 DAIS MILLWORK

Grand total: 1

DATE SUBMISSION/REVISION NO.

ROOM

BCC CHAMBER'S

ID101

REMOVE EXISTING TOP CAP,

EXISTING FRONT FACE PANELING

TO REMAIN

NEW SOLID SURFACE WORK SURFACE

NEW PRESENTATION MONITORS.

COORDINATE SPECS AND DIMENSIONS

WITH OWNER.

NEW CONTINUOUS THIN LED LIGHTING

ID101

N E

W H

H T

O F

S T

O P

S O

S U

R F

A C

E T

O P

A N

D F

R O

N T

EXISTING TOP AREA OF NEW WORK, NEW

SOLID SURFACE TOP AND

FRONT, PROVIDE NEW NAME

PLATES PER STATIONS

EXISTING

WOOD VENEER

PANEL FRONT

EXISTING PRE-

DRILLED HOLES

THRU FRAMING

FOR CABLE RUNS

NEW SOLID SURFACE

COUNTER SURFACE

NEW METAL SUPPORT

BRACKETS - WHERE

REQ'D. FOR

COUNTERTOP SUPPORT

PLATFORM, EXISTING

NEW SOLID SURFACE

TOP AND FRONT PANEL

NEW SOLID SURFACE

TRANSACTION, HEAT

MOLDED RADIUS

10"

1' - 4"

NOTCH OUT

FOR LED

DIODE TAPE

LIGHT

FIXTURE

3/4"

RECEPTACLE

NEW FLIP UP POWER

GROMMET, POWER AND USB

0' - 8 3/4"

N E

W D

H E

NEW LED LIGHTING

E X

S H

H T

NEW MONITOR

NOTCH AT SOLID SURFACE, P-LAM

INTERIOR FOR MONITOR REST

NEW PLAM BACK PANEL

EXISTING

WOOD VENEER

FRONT PANEL

EXISTING PRE-

DRILLED HOLES

THRU FRAMING

FOR CABLE RUNS

EXISTING PLATFORM/

RAMP /STEP

V A

P-LAM BACK

PANEL

SOLID SURFACE

TRANSACTION, HEAT

MOLDED RADIUS

1' - 4"

0' - 8 3/4"

EXISTING

WOOD

VENEER

FRONT PANEL

EXISTING PRE-

DRILLED HOLES

THRU FRAMING

FOR CABLE RUNS

SCHEDULED BASE

NEW SOLID SURFACE

COUNTER SURFACE

NEW METAL SUPPORT

BRACKETS - WHERE

REQ'D. FOR

COUNTERTOP SUPPORT

EXISTING PARTITION

RECEPTACLE

NEW BRUSHED BRONZED

RETRACTABLE GROMMET

GROMMET, COORDINATE FINAL

LOCATIONS WITH OWNER

NEW P-LAM

FRONT PANEL

PREFERED, VERIFY IN FIELD

2' - 0"

SCALE:

DATE:

DRAWN BY:

CHECK BY:

PROJECT NUMBER:

1 2 3 4 5 6 7 8 9 10

ALL REPRODUCTION AND INTELLECTUAL

PROPERTY RIGHTS RESERVED ©

Seal

Consultants

Client

A C CT T SEH IR

605 E. ROBINSON STREET, SUITE 750

ORLANDO, FL 32801

AR0014284

www.rbarchitects.com 407.648.7288

As indicated

ID101

DAIS MILLWORK

05/21/2025

18019

ORANGE COUNTY

ADMINISTRATION

BUILDING BCC

CHAMBERS DAIS

BENCH RENOVATION

ORANGE COUNTY

GOVERNMENT

Permit Documents

SCALE: 1/4" = 1'-0"ID101

FP_01- DAIS RECONFIGURATION

MILLWORK

SCALE: 3/8" = 1'-0"ID101

A4 DAIS ELEVATION

SUBSTITUTIONS

• MATERIALS, PRODUCTS AND EQUIPMENT

SPECIFIED IN CONTRACT DOCUMENTS ESTABLISH

A STANDARD OF QUALITY WITH WHICH PROPOSED

SUBSTITUTIONS MUST COMPLY. REQUESTS FOR

SUBSTITUTIONS SHALL BE SELECTED BY THE

CONTRACTOR AND SUBMITTED TO THE OFFICE OF

THE INTERIOR DESIGNER WITH SPECIFICATIONS

COMPARING SUBSTITUTION WITH THE ORIGINAL

SELECTION. INTERIOR DESIGNER IS NOT

RESPONSIBLE FOR SELECTING ALTERNATE COLOR

AND/OR SPECIFIC MODELS/PATTERNS.

• SUBSTITUTIONS WILL NOT BE CONSIDERED WHEN

THEY ARE INDICATED OR IMPLIED ON SHOP

DRAWINGS OR PRODUCT DATA SUBMITTALS

WITHOUT PRIOR SEPARATE WRITTEN REQUEST OR

WHEN ACCEPTANCE WILL REQUIRE SUBSTANTIAL

REVISION OF CONTRACT DOCUMENTS.

• DESIGNER IS NOT RESPONSIBLE FOR

VERIFICATION OF COMPATIBILITY OF

SUBSTITUTIONS TO OTHER RELATED WORK.

MILLWORK

• ALL MILLWORK DEPICTED HEREIN SHALL COMPLY

WITH STANDARDS FOR CUSTOM GRADE AS

SPECIFIED IN THE CURRENT EDITION OF THE

ARCHITECTURAL WOODWORKER INSTITUTE

STANDARDS.

• MILLWORK SUBCONTRACTOR SHALL SUBMIT SHOP

DRAWINGS FOR APPROVAL TO THE OFFICE OF THE

INTERIOR DESIGNER PRIOR TO ORDERING OF

MATERIALS OR COMMENCEMENT OF WORK.

• ALL ARCHITECTURAL WOODWORK SHALL BE

GUARANTEED TO BE OF GOOD MATERIAL AND

WORKMANSHIP AND FREE FROM DEFECTS THAT

RENDER IT UNSERVICEABLE FOR THE USE FOR

WHICH IT IS INTENDED FOR A PERIOD OF ONE (1)

YEAR AFTER APPROVED FINAL INSTALLATION

DATE.

• ALL ARCHITECTURAL WOODWORK SHALL BE

FACTORY FINISHED WITH TOUCHUP ONLY

OCCURRING IN THE FIELD.

• ALL ARCHITECTURAL WOODWORK OCCURRING AS

WALL PANELING, PILASTERS, SOFFIT CLADDING

SHALL MEET STANDARDS FOR CLASS A (1)

REQUIREMENTS

SOLID SURFACE:

MNF: WILSONART

COLOR: MORNING ICE

PLASTIC LAMINATE:

MNF: WILSONART

COLOR: TO MATCH EXISTING WOOD VENEER PANEL,

PROVIDE SAMPLES FOR ARCHITECT TO VERIFY

SCALE: 1" = 1'-0"ID101

B4 DAIS SECTION

SCALE: 1" = 1'-0"ID101

B7 DAIS SECTION

SCALE: 1" = 1'-0"ID101

E7 DAIS SECTION

DATE SUBMISSION/REVISION NO.

E001

ELECTRICAL GENERAL

NOTES

SCALE:

DATE:

DRAWN BY:

CHECK BY:

PROJECT NUMBER:

1 2 3 4 5 6 7 8 9 10

ALL REPRODUCTION AND INTELLECTUAL

PROPERTY RIGHTS RESERVED ©

Seal

Consultants

Client

A C CT T SEH IR

605 E. ROBINSON STREET, SUITE 750

ORLANDO, FL 32801

AR0014284

www.rbarchitects.com 407.648.7288

As indicated

ABJr

11/14/25

201 S. ROSALIND AVE

ORLANDO, FL 32801

DATE

11/14/25

SUBMISSION/REVISION

PERMIT DOCUMENTS

NO.

CONSTRUCTION DOCUMENTS

THIS ITEM HAS BEEN

ELECTRONICALLY SIGNED AND

SEALED BY AUGUSTO E. BOBES

JR. P.E. ON THE DATE ADJACENT

TO THE SEAL.

PRINTED COPIES OF THIS

DOCUMENT ARE NOT

CONSIDERED SIGNED AND

SEALED AND THE SIGNATURE

MUST BE VERIFIED ON ANY

ELECTRONIC COPIES.

U S T O E . B O B E S , J R

P R O F E S S I O N A L E N G I N E E R

F L O R I D A

L I C E N S E

ORANGE COUNTY

ADMINISTRATION

BUILDING BCC

CHAMBERS DAIS

BENCH RENOVATION

ORANGE COUNTY

GOVERNMENT

18019

AutoCAD SHX Text

%%UELECTRICAL GENERAL NOTES

AutoCAD SHX Text

1. ALL WORK SHALL BE PERFORMED IN ACCORDANCE WITH THE FLORIDA ALL WORK SHALL BE PERFORMED IN ACCORDANCE WITH THE FLORIDA BUILDING CODE 8th EDITION (2023 FBC), THE 2020 NATIONAL ELECTRICAL CODE (NEC), THE CITY OF ORLANDO BUILDING DEPARTMENT, THE CITY OF ORLANDO FIRE MARSHALL, ALL APPLICABLE LOCAL, COUNTY, AND STATE CODES AND STANDARDS, AND ALL REQUIREMENTS OF THE SERVICING ELECTRIC UTILITY. 2. PRIOR TO SUBMITTING THEIR BID FOR THIS WORK, THE CONTRACTOR PRIOR TO SUBMITTING THEIR BID FOR THIS WORK, THE CONTRACTOR SHALL VISIT THE PROJECT JOBSITE AND SHALL FAMILIARIZE THEMSELVES WITH ALL EXISTING BUILDING CONDITIONS, ELECTRICAL SYSTEMS, LOW VOLTAGE SYSTEMS, DEVICES, PANELS ETC. THAT MAY AFFECT THEIR BID. 3. BRANCH WIRING IS NOT SHOWN GRAPHICALLY ON DRAWING AND IS BRANCH WIRING IS NOT SHOWN GRAPHICALLY ON DRAWING AND IS INDICATED BY CIRCUIT NUMBERS BESIDE FIXTURES, DEVICES AND EQUIPMENT. PROVIDE COMPLETE WIRING SYSTEM WHETHER OR NOT INDICATED GRAPHICALLY. 4. LIGHTING FIXTURES ARE SHOWN FOR QUANTITY AND CIRCUITING ONLY. LIGHTING FIXTURES ARE SHOWN FOR QUANTITY AND CIRCUITING ONLY. FOR EXACT LOCATION OF LIGHTING FIXTURES, REFER TO ARCHITECTURAL DAIS MILLWORK PLANS. COORDINATE WORK WITH MILLWORK CONTRACTOR. PROVIDE PROPER FIXTURE MOUNTING. 5. FOR EXACT ARCHITECTURAL LAYOUT AND DIMENSIONS, COORDINATE FOR EXACT ARCHITECTURAL LAYOUT AND DIMENSIONS, COORDINATE WITH ARCHITECTURAL DRAWINGS. ELECTRICAL DRAWINGS ARE FOR REFERENCE ONLY. 6. ALL WORK SHALL BE DONE IN ACCORDANCE WITH THE AMERICANS WITH ALL WORK SHALL BE DONE IN ACCORDANCE WITH THE AMERICANS WITH DISABILITIES ACT (ADA) AND 2020 NATIONAL ELECTRICAL CODE (NEC). 7. COORDINATE ALL WORK DONE UNDER THIS DIVISION WITH WORK TO BE COORDINATE ALL WORK DONE UNDER THIS DIVISION WITH WORK TO BE PERFORMED UNDER THE MECHANICAL DIVISION. 8. COORDINATE WITH OTHER TRADES FOR EXACT LOCATIONS OF ALL COORDINATE WITH OTHER TRADES FOR EXACT LOCATIONS OF ALL MOTORS AND OTHER EQUIPMENT TO BE INSTALLED AND/OR WIRED UNDER THIS DIVISION BUT FURNISHED UNDER ANOTHER DIVISION OF THE SPECIFICATIONS. 9. ALL BRANCH CIRCUITS FOR 120 VOLT, 20 AMP CIRCUITS EXCEEDING ALL BRANCH CIRCUITS FOR 120 VOLT, 20 AMP CIRCUITS EXCEEDING EIGHTY FEET IN LENGTH SHALL BE INCREASED IN SIZE AS REQUIRED TO ALLOW FOR VOLTAGE DROP LOSSES. 10. PACK ALL SLEEVES FOR CONDUITS PASSING THROUGH FIRE RATED PACK ALL SLEEVES FOR CONDUITS PASSING THROUGH FIRE RATED WALLS AND FLOOR SLABS WITH FIRE RESISTANT MATERIALS. ALL PENETRATIONS SHALL BE UL RATED. 11. ALL EMPTY CONDUITS (EC) SHALL BE PROVIDED WITH NYLON PULL ALL EMPTY CONDUITS (EC) SHALL BE PROVIDED WITH NYLON PULL WIRES. 12. TYPE AC CABLE AND ELECTRICAL NON-METALLIC TUBING SHALL NOT TYPE AC CABLE AND ELECTRICAL NON-METALLIC TUBING SHALL NOT BE PERMITTED. TYPE MC CABLE IS PERMITTED AS LONG AS IT IS ACCEPTABLE TO THE LOCAL AUTHORITY HAVING JURISDICTION (AHJ). 13. COORDINATE THE REQUIRED SIZE OF ALL CIRCUIT BREAKERS FEEDING COORDINATE THE REQUIRED SIZE OF ALL CIRCUIT BREAKERS FEEDING EQUIPMENT (I.E. MOTORS, HVAC, KITCHEN EQUIPMENT, SPECIAL PURPOSE OUTLETS, OWNER FURNISHED EQUIPMENT, ETC.) WITH APPROVED EQUIPMENT SHOP DRAWINGS AND OWNER REPRESENTATIVES PRIOR TO ORDERING PANELBOARDS. BREAKERS SHALL BE SIZED PER THE NEC, THE EQUIPMENT NAME PLATE AND MANUFACTURER'S RECOMMENDATIONS. 14. PROVIDE PHENOLIC LABELS ON ALL PANELS AND DISCONNECTS PROVIDE PHENOLIC LABELS ON ALL PANELS AND DISCONNECTS IDENTIFYING WHERE THEY ARE FED FROM. 15. PROVIDE PHENOLIC LABELS ON ALL DISCONNECTS IDENTIFYING THE PROVIDE PHENOLIC LABELS ON ALL DISCONNECTS IDENTIFYING THE ITEM FED BY THE DISCONNECT. 16. THE POWER COMPANY SHALL BE CONTACTED WITHIN 10 DAYS OF THE THE POWER COMPANY SHALL BE CONTACTED WITHIN 10 DAYS OF THE AWARD OF THE CONTRACT BY THE CONTRACTOR TO VERIFY THE ACTUAL AVAILABLE SHORT CIRCUIT FAULT CURRENT (SCC) AT THE TRANSFORMER SECONDARY BUSHINGS. THE CONTRACTOR SHALL PROVIDE ELECTRICAL DISTRIBUTION AND UTILIZATION EQUIPMENT AND PANELBOARDS WHICH HAVE AIC/WITHSTAND RATINGS GREATER THAN THE AVAILABLE SCC. 17. ALL CONDUITS IN OR UNDER SLAB OR UNDERGROUND SHALL BE PVC ALL CONDUITS IN OR UNDER SLAB OR UNDERGROUND SHALL BE PVC SCHEDULE 40. 18. ALL CONDUITS ABOVE SLAB, WHETHER EXPOSED OR CONCEALED, SHALL ALL CONDUITS ABOVE SLAB, WHETHER EXPOSED OR CONCEALED, SHALL BE EMT, IMC, OR RIGID GALVANIZED STEEL. 19. FLEXIBLE METAL RACEWAYS SHALL NOT EXCEED 6' IN LENGTH. FLEXIBLE METAL RACEWAYS SHALL NOT EXCEED 6' IN LENGTH. 20. "LIQUID-TIGHT" TYPE FLEXIBLE WEATHERPROOF RACEWAYS SHALL HAVE "LIQUID-TIGHT" TYPE FLEXIBLE WEATHERPROOF RACEWAYS SHALL HAVE A METALLIC INTERIOR AND NOT EXCEED 6' IN LENGTH. 21. ALL BOXES, PLASTER RINGS, EXTENSION RINGS, AND BOX COVERS ALL BOXES, PLASTER RINGS, EXTENSION RINGS, AND BOX COVERS SHALL BE METAL. 22. ALL CONDUITS SHALL BE PARALLEL AND PERPENDICULAR TO ALL CONDUITS SHALL BE PARALLEL AND PERPENDICULAR TO STRUCTURAL MEMBERS. 23. ALL BENDS SHALL BE MADE IN CONDUIT USING PROPER EQUIPMENT ALL BENDS SHALL BE MADE IN CONDUIT USING PROPER EQUIPMENT AND MEET NATIONAL ELECTRICAL CODE (NEC) REQUIREMENTS. 24. ALL WIRE, INCLUDING BUT NOT LIMITED TO FEEDERS AND BRANCH ALL WIRE, INCLUDING BUT NOT LIMITED TO FEEDERS AND BRANCH CIRCUIT WIRING, SHALL BE COPPER - #12 AWG THWN MINIMUM EXCEPT FOR LOW- VOLTAGE WIRING FOR COMMUNICATIONS SYSTEMS, WHICH MAY BE SMALLER. 25. ALL BREAKERS SHALL BE "FULL SIZE". NO TANDEM, PIGGY BACK, TWIN, ALL BREAKERS SHALL BE "FULL SIZE". NO TANDEM, PIGGY BACK, TWIN, OR HALF SIZE BREAKERS WILL BE ACCEPTED. 26. ALL DEVICES SHALL BE COMMERCIAL OR SPECIFICATION GRADE. ALL DEVICES SHALL BE COMMERCIAL OR SPECIFICATION GRADE. 27. ELECTRICAL CONTRACTOR SHALL BE RESPONSIBLE FOR TEMPORARY ELECTRICAL CONTRACTOR SHALL BE RESPONSIBLE FOR TEMPORARY POWER AND TEMPORARY LIGHTING DURING CONSTRUCTION. TEMPORARY POWER SHALL PROVIDE ADEQUATE POWER FOR NORMAL CONSTRUCTION USE. TEMPORARY LIGHTING SHALL PROVIDE ADEQUATE LIGHT SO THAT THE INDIVIDUAL TRADES WORK CAN BE COMPLETED. 28. ALL ELECTRICAL EQUIPMENT SHALL BE UL LISTED. ALL ELECTRICAL EQUIPMENT SHALL BE UL LISTED. 29. A GREEN INSULATED COPPER GROUND CONDUCTOR SHALL BE A GREEN INSULATED COPPER GROUND CONDUCTOR SHALL BE INSTALLED IN ALL RACEWAYS. 30. GROUNDING SYSTEM SHALL BE IN ACCORDANCE WITH NEC ARTICLE 250 GROUNDING SYSTEM SHALL BE IN ACCORDANCE WITH NEC ARTICLE 250 AND APPLICABLE REQUIREMENTS OF IEEE STANDARDS 142 AND 241. 31. TEST RESISTANCE TO GROUND (EARTHING CONNECTION) WITH TEST RESISTANCE TO GROUND (EARTHING CONNECTION) WITH RESISTANCE TESTER SUBSEQUENT TO FINAL INSTALLATION. WHERE TEST INDICATES RESISTANCE TO GROUND IS OVER 5 OHMS, TAKE APPROPRIATE ACTION TO REDUCE RESISTANCE TO 5 OHMS OR LESS BY DRIVING ADDITIONAL PROPERLY SPACED GROUND RODS AND TREATING SOIL IN PROXIMITY OF GROUND RODS WITH COMMON SALT, COPPER SULFATE OR MAGNESIUM SULFATE. RETEST TO DEMONSTRATE COMPLIANCE. 32. CONDUCTORS ARE SIZED FOR THERMAL CAPACITY PER N.E.C. ARTICLE CONDUCTORS ARE SIZED FOR THERMAL CAPACITY PER N.E.C. ARTICLE 210.19(A)(1) AND VOLTAGE DROP PER ARTICLE 210.19(A) FPN4 AND FBC C405.5.3. ELECTRICAL CONTRACTOR SHALL PERFORM VOLTAGE DROP CALCULATIONS IN ACCORDANCE WITH N.E.C. ARTICLE 210.19 (A) FPN NO. 4 AND F.B.C. C405.5.3 ON ANY CIRCUITS THAT ARE INSTALLED THAT DIFFER FROM THE DESIGN SHOWN IN THESE PLANS. FEEDER CONDUCTORS SHALL BE SIZED FOR A MAXIMUM VOLTAGE DROP OF 2% AND BRANCH CIRCUIT CONDUCTORS 3% AT DESIGN LOAD. 33. THE CONTRACTOR SHALL PROVIDE A COMPLETE ELECTRICAL SHOP THE CONTRACTOR SHALL PROVIDE A COMPLETE ELECTRICAL SHOP DRAWING SUBMITTAL TO THE ENGINEER FOR REVIEW AND APPROVAL. THE ELECTRICAL SUBMITTAL SHALL INCLUDE ALL ELECTRICAL PANELS, MDP'S, BREAKERS, DISCONNECTS, DEVICES, RECEPTACLES, CONDUIT, RACEWAYS, LIGHT FIXTURES, POLES, SWITCHES, OCCUPANCY SENSORS, PULL BOXES, WIRING ETC. CONTRACTOR SHALL NOT ORDER ANY ELECTRICAL EQUIPMENT UNTIL THIS SUBMITTAL IS REVIEWED AND ACCEPTED BY THE ENGINEER OF RECORD. CONTRACTOR SHALL SUBMIT THE SHOP DRAWING AS ONE COMPLETE SUBMITTAL AND SHALL NOT PIECE MEAL THE SUBMITTAL SPREAD OUT OVER THE COURSE OF DAYS AND WEEKS. FAILURE TO SUBMIT A COMPLETE ELECTRICAL SHOP DRAWING SUBMITTAL SHALL RESULT IN AN IMMEDIATE REJECTION OF THE SHOP DRAWING SUBMITTAL.

AutoCAD SHX Text R,S

AutoCAD SHX Text

EWC

AutoCAD SHX Text

ERM

AutoCAD SHX Text

EWH

AutoCAD SHX Text

ERL

AutoCAD SHX Text

EOLR

AutoCAD SHX Text

MCC

AutoCAD SHX Text

NTS

AutoCAD SHX Text

AutoCAD SHX Text G

AutoCAD SHX Text

AFG

AutoCAD SHX Text

EDH

AutoCAD SHX Text

AFF

AutoCAD SHX Text

AutoCAD SHX Text R

AutoCAD SHX Text A

AutoCAD SHX Text H

AutoCAD SHX Text S

AutoCAD SHX Text T

AutoCAD SHX Text V

AutoCAD SHX Text

%%UELECTRICAL SYMBOL LIST

AutoCAD SHX Text M

AutoCAD SHX Text F

AutoCAD SHX Text

AutoCAD SHX Text F

AutoCAD SHX Text

AutoCAD SHX Text F

AutoCAD SHX Text

"FACP"

AutoCAD SHX Text

"FAA"

AutoCAD SHX Text 60A,2P

AutoCAD SHX Text F

AutoCAD SHX Text

AutoCAD SHX Text 30A,3P

AutoCAD SHX Text

AutoCAD SHX Text M

AutoCAD SHX Text C

AutoCAD SHX Text J

AutoCAD SHX Text S

AutoCAD SHX Text #10

AutoCAD SHX Text

LP-1,3,5

AutoCAD SHX Text #5

AutoCAD SHX Text P

AutoCAD SHX Text

AutoCAD SHX Text D

AutoCAD SHX Text T

AutoCAD SHX Text M

AutoCAD SHX Text B

AutoCAD SHX Text a

AutoCAD SHX Text p

AutoCAD SHX Text

AutoCAD SHX Text a

AutoCAD SHX Text A

AutoCAD SHX Text b

AutoCAD SHX Text RECESSED 2'x 4' FLUORESCENT FIXTURE. UPPER CASE LETTER LETTER INDICATES FIXTURE TYPE; SUBSCRIPT LETTER INDICATES SWITCH CONTROL.

AutoCAD SHX Text

RECESSED 1' X 4' FLUORESCENT FIXTURE

AutoCAD SHX Text

SURFACE OR PENDANT MOUNTED FLUORESCENT FIXTURE

AutoCAD SHX Text

SURFACE OR PENDANT MOUNTED FLUORESCENT STRIP

AutoCAD SHX Text

WALL MOUNTED FLUORESCENT FIXTURE

AutoCAD SHX Text INCANDESCENT, FLUORESCENT OR HID DOWNLIGHT. UPPER CASE LETTER INDICATED FIXTURE TYPE: SUBSCRIPT LETTER INDICATES SWITCH CONTROL.

AutoCAD SHX Text

WALL MOUNTED EMERGENCY LIGHT

AutoCAD SHX Text

WALL MOUNTED INCANDESCENT, FLUORESCENT OR HID FIXTURE

AutoCAD SHX Text

SURFACE OR PENDANT MOUNTED INCANDESCENT OR H.I.D. FIXTURE

AutoCAD SHX Text

RECESSED INCANDESCENT OR HID WALL WASHER

AutoCAD SHX Text

WALL MOUNTED FLOODLIGHT. ARROW INDICATTES AIMING DIRECTON

AutoCAD SHX Text

REMOTE EMERGENCY BATTERY PACK HEAD

AutoCAD SHX Text

PHOTOCELL

AutoCAD SHX Text

POLE MOUNTED FLOODLIGHT FIXTURE

AutoCAD SHX Text

POLE MOUNTED FIXTURE

AutoCAD SHX Text CEILING MOUNTED EXIT LIGHT. ARROW INDICATES DIRECTIONAL ARROW ON FIXTURE; SHADED AREA INDICATES FACE OF FIXTURE

AutoCAD SHX Text

WALL OR END MOUNTED EXIT LIGHT

AutoCAD SHX Text SINGLE POLE SWITCH, SUBSCRIPT LETTER INDICATES FIXTURE CONTROLLED. (3=3 WAY; 4=4 WAY) MOUNTED 48" AFF

AutoCAD SHX Text SHADED FIXTURE INDICATES PROVIDED WITH BATTERY PACK CONNECTED AHEAD OF ANY SWITCHING.

AutoCAD SHX Text SINGLE POLE SWITCH. p = PILOT LIGHT; k = KEY OPERATED

AutoCAD SHX Text

MOTOR HORSEPOWER RATED TOGGLE SWITCH BY DIVISION 15

AutoCAD SHX Text

MANUAL MOTOR STARTER WITH THERMAL OVERLOAD PROTECTION

AutoCAD SHX Text

WALL MOUNTED DIMMER. (3 = 3 WAY)

AutoCAD SHX Text

20A 2 POLE 125V GROUNDED SINGLE RECEPTACLE 18"AFF UNLESS OTHERWISE NOTED.

AutoCAD SHX Text 20A, 2 POLE, 125V GROUNDED CONVENIENCE RECEPTACLE. 18" AFF. UNLESS OTHERWISE NOTED.

AutoCAD SHX Text 20A, 2 POLE, 125V GROUNDED DUPLEX CONVENIENCE RECEPTACLE. MOUNTED ABOVE COUNTERTOP UNLESS OTHERWISE NOTED.

AutoCAD SHX Text 20A, 2 POLE, 3 WIRE, 125V GROUNDED DUPLEX RECEPTACLE WITH TOP HALF SWITCHED. 18" AFF. UNLESS OTHERWISE NOTED.

AutoCAD SHX Text

(2) 20A, 2 POLE, 125V GROUNDED CONVENIENCE RECEPTACLE. 18" AFF. UNLESS OTHERWISE NOTED.

AutoCAD SHX Text

(2) 20A, 2P, 3W, 125V GROUNDED DUPLEX RECEPTACLES IN 2-GANG BOX. MOUNTED ABOVE COUNTERTOP, UNLESS OTHERWISE NOTED.

AutoCAD SHX Text

SPECIAL RECEPTACLE AS DESIGNATED ON DRAWINGS

AutoCAD SHX Text CAST IRON FULLY ADJUSTABLE FLOOR BOX WITH ONE 20A, 125V, 2P, 3W DUPLEX RECEPTACLE FLOOR BOX STEEL CITY CAT.#601-P60-CP-P60-DS - COVER PLATE SHALL BE BRASS.

AutoCAD SHX Text

TELEPHONE OUTLET MOUNTED IN FLUSH FLOOR BOX.

AutoCAD SHX Text TELEPHONE WALL OUTLET 18" AFF UNLESS OTHERWISE NOTED P = PAY PHONE OUTLET MOUNTED 48" AFF. PROVIDE 3/4" EC STUB-UP AND TERMINATE 6" ABOVE CEILING. TURN CONDUIT INTO ROOM IT SERVES

AutoCAD SHX Text COMPUTER/TELEPHONE OUTLET BOX 4 11/16"x4 11/16"x2 3/4" DEEP, FLUSH MOUNTED, 18"AFF UNLESS NOTED OTHERWISE, WITH 1"EC STUB-UP 6" ABOVE SUSPENDED CEILING, WITH CONDUIT TURNING INTO ROOM IT SERVES. PROVIDE TRIM RING AS REQUIRED TO ACCOMODATE WALL CONSTRUCTION AND FACEPLATE.

AutoCAD SHX Text COMPUTER OUTLET BOX 4 11/16"x4 11/16"x2 3/4" DEEP, FLUSH MOUNTED 18"AFF UNLESS NOTED OTHERWISE, WITH 1"EC STUB-UP 6" ABOVE SUSPENDED CEILING, WITH CONDUIT TURNING INTO ROOM IT SERVES. PROVIDE TRIM RING RING AS REQUIRED TO ACCOMODATE WALL CONSTRUCTION AND FACEPLATE.

AutoCAD SHX Text TELEVISION OUTLET WITH 1"EC STUB-UP 6" ABOVE SUSPENDED CEILING, WITH CONDUIT TURNED INTO ROOM IT SERVES

AutoCAD SHX Text

CLOCK OUTLET

AutoCAD SHX Text

CLOCK OUTLET WITH CLOCK

AutoCAD SHX Text CONDUIT RUN CONCEALED IN CEILING OR PARTITION. (1/2"C-2#12, 1#12 GND MINIMUM) HALF ARROWHEAD INDICATE CIRCUIT BREAK.

AutoCAD SHX Text CONCEALED BRANCH CIRCUIT WIRING, HASH MARKS INDICATE NUMBER OF CONDUCTORS (GROUND CONDUCTOR NOT SHOWN) TWO CONDUCTORS PLUS GROUND REQUIRED (UNLESS OTHERWISE NOTED). LP-1,3,5 INDICATE HOMERUN TO PANEL BOARD AND CIRCUIT NUMBER DESIGNATION.

AutoCAD SHX Text

CONDUIT RUN BELOW GRADE OR IN SLAB

AutoCAD SHX Text

CONDUIT RUN EXPOSED

AutoCAD SHX Text CONDUIT HOMERUN. HASH MARKS INDICATE NUMBER OF WIRES; NUMBER ADJACENT TO HASH MARKS INDICATE WIRE SIZE

AutoCAD SHX Text

CONDUIT TURNING UP

AutoCAD SHX Text

CONDUIT TURNING DOWN

AutoCAD SHX Text

CEILING MOUNTED JUNCTION BOX

AutoCAD SHX Text

WALL MOUNTED JUNCTION BOX

AutoCAD SHX Text

CEILING MOUNTED SPEAKER

AutoCAD SHX Text

WALL MOUNTED SPEAKER

AutoCAD SHX Text CAST IRON FULLY ADJUSTABLE FLOOR BOX WITH ONE MICROPHONE JACK. FLOOR BOX STEEL CITY CAT.#601-P60-CP-P60-DS - COVER PLATE SHALL BE BRASS.

AutoCAD SHX Text WALL MOUNTED OUTLET BOX WITH MICROPHONE JACK AND COVER PLATE MOUNTED 18" AFF UNLESS OTHERWISE NOTED.

AutoCAD SHX Text

CONNECTION TO EQUIPMENT

AutoCAD SHX Text EMERGENCY POWER OFF BREAK GLASS PUSH-BUTTON MOUNT 6'-6" AFF OR AS DIRECTED BY THE FIRE MARSHAL.

AutoCAD SHX Text

MAGNETIC MOTOR STARTER

AutoCAD SHX Text COMBINATION MAGNETIC MOTOR STARTER AND DISCONNECT SWITCH. ROMAN NUMERALS INDICATE STARTER SIZE; NUMBERS INDICATE SWITCH OR CIRCUIT BREAKER SIZE

AutoCAD SHX Text

UNFUSED DISCONNECT SWITCH. NUMBERS INDICATE SWITCH SIZE

AutoCAD SHX Text

FUSED DISCONNECT SWITCH. FUSES SIZED AS SHOWN ON DRAWINGS

AutoCAD SHX Text

MOTOR

AutoCAD SHX Text

PANELBOARD, 120/208V, 3 , 4W

AutoCAD SHX Text

TELEPHONE TERMINAL BOARD

AutoCAD SHX Text

FIRE ALARM CONTROL PANEL

AutoCAD SHX Text

FIRE ALARM REMOTE ANNUNCIATOR

AutoCAD SHX Text

METER SOCKET

AutoCAD SHX Text

FLUSH IN-GRADE PULL-BOX

AutoCAD SHX Text

FIRE ALARM MANUAL PULL STATION, MOUNTED 48" AFF

AutoCAD SHX Text

FIRE ALARM SPEAKER WITH STROBE LIGHT, MOUNTED 80" AFF

AutoCAD SHX Text

FIRE ALARM STROBE LIGHT, MOUNTED 80" AFF

AutoCAD SHX Text

FIRE SPRINKLER FLOW SWITCH

AutoCAD SHX Text

FIRE SPRINKLER TAMPER SWITCH

AutoCAD SHX Text

AUTOMATIC HEAT DETECTOR - FIXED TEMPERATURE ONLY

AutoCAD SHX Text

SMOKE DUCT DETECTOR, R=RETURN DUCT, S=SUPPLY DUCT

AutoCAD SHX Text

SMOKE DETECTOR

AutoCAD SHX Text

HEAT DETECTOR

AutoCAD SHX Text

AHU FIRE ALARM SHUTDOWN RELAY

AutoCAD SHX Text

CONTACTOR

AutoCAD SHX Text

TIME CLOCK

AutoCAD SHX Text

GROUND OR GROUND ROD AS NOTED

AutoCAD SHX Text

INFRA-RED SENSOR, FURNISHED AND INSTALLED BY DIV. 15, WIRED BY DIV. 16

AutoCAD SHX Text

SOLENOID VALVE, FURNISHED AND INSTALLED BY DIV. 15, WIRED BY DIV. 16

AutoCAD SHX Text

TRANSFORMER, 120-24 VOLT FURNISHED BY DIV. 15, INSTALLED AND WIRED BY DIV. 16

AutoCAD SHX Text

CEILING MOUNTED SPEAKER AND STROBE

AutoCAD SHX Text

CEILING MOUNTED HORN AND STROBE

AutoCAD SHX Text

ATTENUATOR

AutoCAD SHX Text

ABOVE FINISH FLOOR

AutoCAD SHX Text

ABOVE FINISH GRADE

AutoCAD SHX Text

CURRENT TRANSFORMER

AutoCAD SHX Text

EMPTY CONDUIT

AutoCAD SHX Text

ELECTRIC DUCT HEATER

AutoCAD SHX Text

EXHAUST FAN

AutoCAD SHX Text

END OF LINE RESISTOR

AutoCAD SHX Text

EXISTING RELOCATED

AutoCAD SHX Text

EXISTING TO BE RELOCATED

AutoCAD SHX Text

EXISTING TO BE REMOVED

AutoCAD SHX Text

ELECTRIC WATER COOLER

AutoCAD SHX Text

ELECTRIC WATER HEATER

AutoCAD SHX Text

GROUND FAULT INTERRUPTER

AutoCAD SHX Text

NIGHT LIGHT

AutoCAD SHX Text

JUNCTION BOX

AutoCAD SHX Text

MOTOR CONTROL CENTER

AutoCAD SHX Text

NOT TO SCALE

AutoCAD SHX Text

PUSH BUTTON

AutoCAD SHX Text

PULL CHAIN

AutoCAD SHX Text

POTENTIAL TRANSFORMER

AutoCAD SHX Text

VAPOR-PROOF

AutoCAD SHX Text

WEATHERPROOF (NEMA-3R)

AutoCAD SHX Text

EXPLOSION-PROOF

AutoCAD SHX Text DATA OUTLET MOUNTED IN CAST IRON FULLY ADJUSTABLE FLOOR BOX WITH ONE DATA OUTLET. STEEL CITY CAT.#601-P60PCP-P60-DS COVER PLATE SHALL BE BRASS.

AutoCAD SHX Text

SHUNT TRIP

AutoCAD SHX Text

CONDUIT CAPPED OFF

AutoCAD SHX Text

PANELBOARD, 277/480V, 3 , 4W

AutoCAD SHX Text

FIRE ALARM TERMINAL CABINET

AutoCAD SHX Text

"FATC"

AutoCAD SHX Text

FIRE ALARM FLOOR MOUNTED ELECTRO-MAGNETIC DOOR RELEASE

AutoCAD SHX Text

FIRE ALARM WALL MOUNTED ELECTRO-MAGNETIC DOOR RELEASE

AutoCAD SHX Text

%%USCOPE OF WORK

AutoCAD SHX Text THE ELECTRICAL/LOW VOLTAGE SCOPE OF WORK FOR THIS PROJECT INCLUDES, BUT IS NOT LIMITED TO THE FOLLOWING: 1. REMOVE EXISTING DURESS CALL BUTTONS AND MONITORS ON THE REMOVE EXISTING DURESS CALL BUTTONS AND MONITORS ON THE EXISTING DAIS BENCH. 2. FURNISH AND INSTALL NEW POWER RECEPTACLES, WIRING AND FURNISH AND INSTALL NEW POWER RECEPTACLES, WIRING AND CONDUIT AS INDICATED ON THE RENOVATION PLAN. 3. FURNISH AND INSTALL NEW ABOVE COUNTER LIGHTING WIRING, FURNISH AND INSTALL NEW ABOVE COUNTER LIGHTING WIRING, CONDUIT AND SWITCHES AS INDICATED ON THE RENOVATION PLANS. 4. ROUTE EMPTY CONDUIT FROM EXISTING IDF RACK TO NEW DAIS BENCH ROUTE EMPTY CONDUIT FROM EXISTING IDF RACK TO NEW DAIS BENCH MONITORS. SEE RENOVATION PLANS. ALL DATA CABLING AND DEVICES SHALL BE FURNISHED AND INSTALLED BY OTHERS. 5. FURNISH AND INSTALL NEW UNDER COUNTER DURESS CALL BUTTONS FURNISH AND INSTALL NEW UNDER COUNTER DURESS CALL BUTTONS AS INDICATED ON THE RENOVATION PLAN. SEE RENOVATION PLANS.

AutoCAD SHX Text

WAP

AutoCAD SHX Text

WIRELESS ACCESS POINT

AutoCAD SHX Text

MOTION DETECTOR

AutoCAD SHX Text F

AutoCAD SHX Text

CEILING MOUNTED FIRE ALARM SPEAKER

AutoCAD SHX Text

CARD READER

AutoCAD SHX Text

REQUEST TO EXIT MOTION DETECTOR

AutoCAD SHX Text

DOOR POSITION CONTACT

AutoCAD SHX Text

ELECTRIC STRIKE/LOCKSET

AutoCAD SHX Text

DSCP

AutoCAD SHX Text

DURESS ALARM WIRELESS RECEIVER CONTROL PANEL

AutoCAD SHX Text

UNDERCOUNTER WIRELESS DURESS ALARM TRANSMITTER CALL BUTTON

AutoCAD SHX Text

ACP

AutoCAD SHX Text

ACCESS CONTROL PANEL

AutoCAD SHX Text

ACPS

AutoCAD SHX Text

ACCESS CONTROL POWER SUPPLY

AutoCAD SHX Text

ELECTRIC MORTISE LOCK

AutoCAD SHX Text F

AutoCAD SHX Text

DISCUSSION UNIT SPEAKER/MICROPHONE

AutoCAD SHX Text

FLORIDA STATE P.E. NUMBER: 5131

AutoCAD SHX Text

TELEPHONE: 407.628.0882

AutoCAD SHX Text

150 CIRCLE DRIVE, MAITLAND, FL 32751

AutoCAD SHX Text

E-MAIL: INFO@BOBESENG.COM

AutoCAD SHX Text

STATE OF

AutoCAD SHX Text No 39410

E101

POWER + LIGHTING +

SYSTEMS

DEMOLITION PLAN

SCALE: 1/4" = 1'-0"E101

A1 PARTIAL FIRST FLOOR PLAN - POWER+LIGHTING+SYSTEMS - DEMOLITION

SCALE:

DATE:

DRAWN BY:

CHECK BY:

PROJECT NUMBER:

1 2 3 4 5 6 7 8 9 10

ALL REPRODUCTION AND INTELLECTUAL

Seal

Consultants

Client

A C CT T SEH IR

605 E. ROBINSON STREET, SUITE 750

ORLANDO, FL 32801

AR0014284

www.rbarchitects.com 407.648.7288

As indicated

ABJr

09/19/25

201 S. ROSALIND AVE

ORLANDO, FL 32801

DATE

09/19/25

SUBMISSION/REVISION

90% CONSTRUCTION DOCS

NO.

CONSTRUCTION DOCUMENTS

THIS ITEM HAS BEEN

ELECTRONICALLY SIGNED AND

SEALED BY AUGUSTO E. BOBES

JR. P.E. ON THE DATE ADJACENT

TO THE SEAL.

PRINTED COPIES OF THIS

DOCUMENT ARE NOT

CONSIDERED SIGNED AND

SEALED AND THE SIGNATURE

MUST BE VERIFIED ON ANY

ELECTRONIC COPIES.

U S T O E . B O B E S , J R

P R O F E S S I O N A L E N G I N E E R

F L O R I D A

L I C E N S E

ORANGE COUNTY

ADMINISTRATION

BUILDING BCC

CHAMBERS DAIS

BENCH RENOVATION

ORANGE COUNTY

GOVERNMENT

18019

F.E.C.

F.H.C.

KEY PLAN

AutoCAD SHX Text

VESTIBULE

AutoCAD SHX Text

SOUND

AutoCAD SHX Text

VESTIBULE

AutoCAD SHX Text

SOUND

AutoCAD SHX Text

ROOM

AutoCAD SHX Text

BCC CHAMBERS

AutoCAD SHX Text

MEDIA ROOM

AutoCAD SHX Text

BCC CHAMBER'S

AutoCAD SHX Text

ELEVATOR LOBBY

AutoCAD SHX Text

BCC CHAMBER'S

AutoCAD SHX Text 103A

AutoCAD SHX Text

STAIRS

AutoCAD SHX Text

CONFERENCE ROOM

AutoCAD SHX Text

BCC CHAMBER'S

AutoCAD SHX Text

ELEV

AutoCAD SHX Text E01

AutoCAD SHX Text %%uELECTRICAL DEMOLITION KEY NOTES

AutoCAD SHX Text

AutoCAD SHX Text EXISTING DAIS BENCH TO REMAIN AND BE REFURBISHED/RECONFIGURED. EXISTING MONITOR RECESSED IN MILLWORK TO BE REMOVED. TURN MONITORS OVER TO OWNER FOR DISPOSITION. EXISTING ABOVE COUNTER LIGHTING TO BE REMOVED. CONTRACTOR SHALL REMOVE ALL ASSOCIATED CONDUIT, WIRING AND SWITCHES. EXISTING DURESS CALL BUTTON TO BE REMOVED. EXISTING DURESS ALARM WIRELESS RECEIVER CONTROL PANEL BE REMOVED. DO NOT REMOVE INTEGRATION CIRCUITS WITH ACCESS CONTROL PANEL. REFER TO RENOVATION DRAWINGS FOR ADDITIONAL REQUIREMENTS. FIELD VERIFY EXACT LOCATION. COORDINATE WITH ORANGE COUNTY ISS ENTERPRISE SECURITY PRIOR RIOR TO REMOVAL. EXISTING ACCESS CONTROL PANEL AND POWER SUPPLY SHOWN FOR REFERENCE. COORDINATE DURESS ALARM REMOVAL WITH ORANGE COUNTY ISS ENTERPRISE SECURITY. EXISTING VGA DISTRIBUTION AMPLIFIER TO REMOVED AND REPLACED WITH NEW OWNER FURNISHED 16 OUTPUT VGA AMPLIFIER. EXISTING COUNTER TOP MOUNTED MICROPHONES TO BE REMOVED. CONTRACTOR SHALL REMOVE ALL ASSOCIATED WIRING BACK TO SOURCE. LOCATION OF EXISTING SOUND MIXER BOARD. EXISTING VOICE/DATA COMMUNICATIONS OUTLET AND WIRING TO REMAIN.

AutoCAD SHX Text

TYPICAL

AutoCAD SHX Text

EXISTING IDF RACK

AutoCAD SHX Text

TYPICAL

AutoCAD SHX Text

DSCP

AutoCAD SHX Text

AutoCAD SHX Text %%uELECTRICAL DEMOLITION NOTES

AutoCAD SHX Text

1. PRIOR TO THE COMMENCEMENT OF DEMOLITION, THE ELECTRICAL PRIOR TO THE COMMENCEMENT OF DEMOLITION, THE ELECTRICAL CONTRACTOR SHALL MEET WITH THE ORANGE COUNTY PROJECT MANAGER, O.C. ADMINISTRATION BUILDING FACILITIES STAFF AND OC ISS STAFF AT THIS PROJECT SITE AND SHALL IDENTIFY ALL EXISTING ELECTRICAL, LOW VOLTAGE, SOUND AND DURESS SYSTEMS ETC. IN THE DAIS TO BE REMOVED. CONTRACTOR SHALL DETERMINE WHAT, IF ANY OF THE DEVICES SHALL BE TURNED OVER TO THE OWNER. ALL OTHER DEVICES, OUTLETS, CABLING ETC. SHALL BE DISPOSED OF BY THE CONTRACTOR.

AutoCAD SHX Text

VGA AMP

AutoCAD SHX Text

SND MIXER

AutoCAD SHX Text

ACPS

AutoCAD SHX Text

ACP

AutoCAD SHX Text

TYPICAL

AutoCAD SHX Text

FLORIDA STATE P.E. NUMBER: 5131

AutoCAD SHX Text

TELEPHONE: 407.628.0882

AutoCAD SHX Text

150 CIRCLE DRIVE, MAITLAND, FL 32751

AutoCAD SHX Text

E-MAIL: INFO@BOBESENG.COM

AutoCAD SHX Text

STATE OF

AutoCAD SHX Text No 39410

AutoCAD SHX Text

EXISTING UNDERCOUNTER POWER AND DATA WIRING TO REMAIN

AutoCAD SHX Text

EXISTING UNDERCOUNTER POWER AND DATA OUTLETS TO REMAIN

AutoCAD SHX Text EXISTING UNDERCOUNTER POWER TO REMAIN AND ABOVE COUNTER LIGHT FIXTURE TO BE REMOVED

AutoCAD SHX Text

VESTIBULE

AutoCAD SHX Text

ENTRY

AutoCAD SHX Text

LOBBY

AutoCAD SHX Text

ATRIUM

AutoCAD SHX Text

LOBBY

AutoCAD SHX Text

ELEVATOR

AutoCAD SHX Text

VESTIBULE

AutoCAD SHX Text

VESTIBULE

AutoCAD SHX Text

ELECTRICAL

AutoCAD SHX Text

TELEPHONE

AutoCAD SHX Text

VESTIBULE

AutoCAD SHX Text

ELECTRICAL

AutoCAD SHX Text

TELEPHONE

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

OPEN

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

STORAGE

AutoCAD SHX Text

PLANS

AutoCAD SHX Text

CONFERENCE

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

MANAGER

AutoCAD SHX Text

CLOSET

AutoCAD SHX Text

AREA

AutoCAD SHX Text

COPY

AutoCAD SHX Text

AREA

AutoCAD SHX Text

RECEPTION

AutoCAD SHX Text

AREA

AutoCAD SHX Text

WAITING

AutoCAD SHX Text 112A

AutoCAD SHX Text

STORAGE

AutoCAD SHX Text

IT ROOM

AutoCAD SHX Text

ELECTRICAL

AutoCAD SHX Text

GENERATOR

AutoCAD SHX Text

SECURITY

AutoCAD SHX Text

RECEIVINF AREA

AutoCAD SHX Text

STORAGE

AutoCAD SHX Text

STORAGE

AutoCAD SHX Text 183A

AutoCAD SHX Text

LOBBY

AutoCAD SHX Text

SERV ELEV

AutoCAD SHX Text 112C

AutoCAD SHX Text

STORAGE

AutoCAD SHX Text

VESTIBULE

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

OPEN

AutoCAD SHX Text

STORAGE

AutoCAD SHX Text 190A

AutoCAD SHX Text

RR VESTIBULE

AutoCAD SHX Text

RR VESTIBULE

AutoCAD SHX Text

CASHIER

AutoCAD SHX Text

CONTRACTOR

AutoCAD SHX Text

LICENSING

AutoCAD SHX Text

BLDG SAFETY

AutoCAD SHX Text

DIVISION OF

AutoCAD SHX Text

STORAGE

AutoCAD SHX Text

PLANS

AutoCAD SHX Text

VESTIBULE

AutoCAD SHX Text

ENTRY

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

SPECIALIST

AutoCAD SHX Text

ADMIN

AutoCAD SHX Text 130A

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

VESTIBULE

AutoCAD SHX Text

SOUND

AutoCAD SHX Text

VESTIBULE

AutoCAD SHX Text

SOUND

AutoCAD SHX Text

ROOM

AutoCAD SHX Text

BCC CHAMBERS

AutoCAD SHX Text

RESTROOM

AutoCAD SHX Text

MALE'S

AutoCAD SHX Text 109A

AutoCAD SHX Text

RESTROOM

AutoCAD SHX Text

FEMALE'S

AutoCAD SHX Text 110A

AutoCAD SHX Text

RESTROOM

AutoCAD SHX Text

MALE'S

AutoCAD SHX Text 117A

AutoCAD SHX Text

RESTROOM

AutoCAD SHX Text

FEMALE'S

AutoCAD SHX Text 118A

AutoCAD SHX Text

MEDIA ROOM

AutoCAD SHX Text

BCC CHAMBER'S

AutoCAD SHX Text

ELEVATOR LOBBY

AutoCAD SHX Text

BCC CHAMBER'S

AutoCAD SHX Text 103A

AutoCAD SHX Text

STAIRS

AutoCAD SHX Text S01

AutoCAD SHX Text

CONFERENCE ROOM

AutoCAD SHX Text

BCC CHAMBER'S

AutoCAD SHX Text

STORAGE

AutoCAD SHX Text 106A

AutoCAD SHX Text

SPECIALIST

AutoCAD SHX Text

ADMIN

AutoCAD SHX Text 130B

AutoCAD SHX Text

CLOSET

AutoCAD SHX Text 135A

AutoCAD SHX Text

ELECTRICAL

AutoCAD SHX Text

TELEPHONE

AutoCAD SHX Text

STAIR

AutoCAD SHX Text S03

AutoCAD SHX Text

ELEV

AutoCAD SHX Text

SERV

AutoCAD SHX Text E04

AutoCAD SHX Text

MECH

AutoCAD SHX Text 180B

AutoCAD SHX Text

ELECTRICAL

AutoCAD SHX Text 180C

AutoCAD SHX Text

CORRIDOR

AutoCAD SHX Text 180A

AutoCAD SHX Text

CORRIDOR

AutoCAD SHX Text 112B

AutoCAD SHX Text

ATM ROOM

AutoCAD SHX Text 100B

AutoCAD SHX Text

STORAGE

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

OPEN

AutoCAD SHX Text

DEPARTMENT

AutoCAD SHX Text

PLANNING & ZONING

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

CLOSET

AutoCAD SHX Text

STORAGE

AutoCAD SHX Text 100A

AutoCAD SHX Text

STAIRS

AutoCAD SHX Text S02

AutoCAD SHX Text

ELEV

AutoCAD SHX Text E02

AutoCAD SHX Text

ELEV

AutoCAD SHX Text E03

AutoCAD SHX Text

ELEV

AutoCAD SHX Text E01

AutoCAD SHX Text

ROOM

AutoCAD SHX Text

CONFERENCE

AutoCAD SHX Text

ROOM

AutoCAD SHX Text

BREAK

AutoCAD SHX Text

STORAGE

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

OPEN

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

OPEN

AutoCAD SHX Text

AREA

AutoCAD SHX Text

SECRETARY

AutoCAD SHX Text

LEADER TEXT-120

AutoCAD SHX Text

EXISTING DAIS TO REMAIN AND BE REFURBISHED

EXISTING UNDERCOUNTER POWER AND DATA OUTLETS TO BE REMAIN

E102

POWER + LIGHTING +

SYSTEMS RENOVATION

PLAN

SCALE:

DATE:

DRAWN BY:

CHECK BY:

PROJECT NUMBER:

1 2 3 4 5 6 7 8 9 10

ALL REPRODUCTION AND INTELLECTUAL

Seal

Consultants

Client

A C CT T SEH IR

605 E. ROBINSON STREET, SUITE 750

ORLANDO, FL 32801

AR0014284

www.rbarchitects.com 407.648.7288

As indicated

ABJr

11/14/25

201 S. ROSALIND AVE

ORLANDO, FL 32801

DATE

11/14/25

SUBMISSION/REVISION

PERMIT DOCUMENTS

NO.

CONSTRUCTION DOCUMENTS

THIS ITEM HAS BEEN

ELECTRONICALLY SIGNED AND

SEALED BY AUGUSTO E. BOBES

JR. P.E. ON THE DATE ADJACENT

TO THE SEAL.

PRINTED COPIES OF THIS

DOCUMENT ARE NOT

CONSIDERED SIGNED AND

SEALED AND THE SIGNATURE

MUST BE VERIFIED ON ANY

ELECTRONIC COPIES.

U S T O E . B O B E S , J R

P R O F E S S I O N A L E N G I N E E R

F L O R I D A

L I C E N S E

ORANGE COUNTY

ADMINISTRATION

BUILDING BCC

CHAMBERS DAIS

BENCH RENOVATION

ORANGE COUNTY

GOVERNMENT

18019

SCALE: 1/4" = 1'-0"E102

A1 PARTIAL FIRST FLOOR PLAN - LIGHTING - RENOVATION

SCALE: 1/4" = 1'-0"E102

A2 PARTIAL FIRST FLOOR PLAN - POWER - RENOVATION

SCALE: 1/4" = 1'-0"E102

A4 PARTIAL FIRST FLOOR PLAN - SYSTEMS - RENOVATION

F.E.C.

F.H.C.

KEY PLAN

AutoCAD SHX Text

ROOM

AutoCAD SHX Text

BCC CHAMBERS

AutoCAD SHX Text

AutoCAD SHX Text B

AutoCAD SHX Text 3a

AutoCAD SHX Text 3b

AutoCAD SHX Text 3a

AutoCAD SHX Text 3b

AutoCAD SHX Text LI5-45b

AutoCAD SHX Text LI5-45a

AutoCAD SHX Text %%uLIGHTING KEY NOTES

AutoCAD SHX Text

AutoCAD SHX Text NEW ABOVE COUNTER LED LIGHTING STRIP. CONNECT TO EXISTING LOCAL CIRCUIT. SEE MILLWORK SECTION FOR EXACT LOCATION AND MOUNTING. NEW DIODE TAPE LIGHT FIXTURE IN NOTCH OUT. SEE MILLWORK DRAWINGS FOR EXACT LOCATION.

AutoCAD SHX Text

VESTIBULE

AutoCAD SHX Text

ROOM

AutoCAD SHX Text

BCC CHAMBERS

AutoCAD SHX Text

TYPICAL

AutoCAD SHX Text

LI5-65

AutoCAD SHX Text

LI5-67

AutoCAD SHX Text

LI5-67

AutoCAD SHX Text

LI5-67

AutoCAD SHX Text

LI5-67

AutoCAD SHX Text

LI5-67

AutoCAD SHX Text

LI5-65

AutoCAD SHX Text

LI5-65

AutoCAD SHX Text

LI5-65

AutoCAD SHX Text

LI5-65

AutoCAD SHX Text %%uPOWER KEY NOTES

AutoCAD SHX Text

AutoCAD SHX Text NEW ABOVE COUNTER RECEPTACLE WITH USB AND USB-C CONNECTIONS. CONNECT TO EXISTING LOCAL CIRCUIT. SEE MILLWORK DRAWINGS FOR EXACT LOCATION.

AutoCAD SHX Text

VESTIBULE

AutoCAD SHX Text

ROOM

AutoCAD SHX Text

BCC CHAMBERS

AutoCAD SHX Text

AutoCAD SHX Text %%uSYSTEMS KEY NOTES

AutoCAD SHX Text

AutoCAD SHX Text PROVIDE UNDERCOUNTER MOUNTED WIRELESS DURESS ALARM CALL BUTTON. COORDINATE WITH ARCHITECT AND ORANGE COUNTY SECURITY PRIOR TO INSTALLATION. NEW WIRELESS DURESS RECEIVER. PROVIDE ALL REQUIRED INPUT CONNECTIONS TO EXISTING ACCESS CONTROL INPUT/OUTPUT MODULE. ALL DURESS ALARM TRANSMITTER BUTTONS SHALL HAVE A DEDICATED INPUT ON THE ACCESS CONTROL. COORDINATE WITH ORANGE COUNTY SECURITY. REFER TO DURESS ALARM ONE LINE DIAGRAM FOR ADDITIONAL INFORMATION. EXISTING ACCESS CONTROL PANEL AND POWER SUPPLY SHOWN FOR REFERENCE. COORDINATE NEW DURESS ALARM INSTALLATION WITH ORANGE COUNTY ISS ENTERPRISE SECURITY. NEW OWNER FURNISHED CONTRACTOR INSTALLED 16 OUTPUT VGA DISTRIBUTION AMPLIFIER. REFER TO VGA SIGNAL DISTRIBUTION ONE LINE DIAGRAM. PROVIDE (6), PLENUM RATED RGB 25 AWG. SVGA VIDEO CABLES. RUN CABLES FROM VGA DISTRIBUTION AMPLIFIER TO NEW COMPUTER MONITOR LOCATIONS INSTALLED IN DAIS. PROVIDE HD15 VGA CONNECTORS AT EACH END. REWORK ROUTING OF EXISTING VGA CABLES TO REMAINING COMPUTER MONITORS INSTALLED. NEW VGA MONITORS ARE OWNER FURNISHED CONTRACTOR INSTALLED. COORDINATE WITH ARCHITECTURAL DRAWINGS. PROVIDE DISCUSSION SYSTEM CONTROLLER. INSTALL UNIT IN THE EXISTING MILLWORK HOUSING THE EXISTING AUDIO EQUIPMENT. REFER TO DISCUSSION SYSTEM ONE LINE DIAGRAM. PROVIDE COUNTER TOP MOUNTED DISCUSSION UNIT WITH INTEGRAL SPEAKER AND 18" GOOSENECK MICROPHONE. (TYPICAL)

AutoCAD SHX Text

VGA AMP

AutoCAD SHX Text

SND MIXER

AutoCAD SHX Text

DSCP

AutoCAD SHX Text

ACPS

AutoCAD SHX Text

ACP

AutoCAD SHX Text

DISCUSSION CONT

AutoCAD SHX Text

FLORIDA STATE P.E. NUMBER: 5131

AutoCAD SHX Text

TELEPHONE: 407.628.0882

AutoCAD SHX Text

150 CIRCLE DRIVE, MAITLAND, FL 32751

AutoCAD SHX Text

E-MAIL: INFO@BOBESENG.COM

AutoCAD SHX Text

STATE OF

AutoCAD SHX Text No 39410

AutoCAD SHX Text

VESTIBULE

AutoCAD SHX Text

ENTRY

AutoCAD SHX Text

LOBBY

AutoCAD SHX Text

ATRIUM

AutoCAD SHX Text

LOBBY

AutoCAD SHX Text

ELEVATOR

AutoCAD SHX Text

VESTIBULE

AutoCAD SHX Text

VESTIBULE

AutoCAD SHX Text

ELECTRICAL

AutoCAD SHX Text

TELEPHONE

AutoCAD SHX Text

VESTIBULE

AutoCAD SHX Text

ELECTRICAL

AutoCAD SHX Text

TELEPHONE

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

OPEN

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

STORAGE

AutoCAD SHX Text

PLAN…

This is the start of the file's text. The full file is on GovTribe.

File details come from the government source that posted it. Updated Apr 13, 2026.