Attachment 1 Range Control.PDF

P.O. Box 25 ♦ 232 Heilman Avenue Henderson, KY. 42419 Tel. (270) 830-8512 ♦ Fax (270) 228-4551 www.allstatetower.com Full Service Tower Company ♦ Licensed Engineering Firm ♦ Tower Steel

Maintenance ♦ Inspection♦ Design-Build Steel Manufacturing ♦ Modification Structural Steel ♦ Material Handling Solutions

CUSTOMER:

SITE NAME:

JOB NO:

TYPE OF TOWER:

TOWER HEIGHT:

A&T Systems

RANGE CONTROL

IN-078128

Guyed 260'

INSPECTION DATE: 2019-04-08

For questions or concerns regarding your Allstate Tower Inspection Report please contact:

Von Hannah Director of Inspections

O 270-228-4934 C 812-664-2762 vhannah@pttg.com

©2014.ALLSTATE TOWER ALL RIGHTS RESERVED. REPRODUCTION OR TRANSLATION OF ANY PART OF THIS INSPECTION REPORT BY ANY MEANS, ELECTRONIC OR MECHANICAL, WITHOUT THE EXPRESSED WRITTEN CONDITION OF ALLSTATE TOWER UNLAWFUL AND A VIOLATION OF UNITED STATES COPYRIGHT LAWS. SUBMIT WRITTEN REQUESTS TO:

ALLSTATE TOWER, P.O. BOX 25, HENDERSON, KY 42419.

http://www.allstatetower.com

Allstate Tower Inspection Report Table of Contents

Definition of Terminology i Detail of Repair Work ii Work Required Within 3-5 Years iii Recommendations Concluded iv Tower Inspection Report 1

1. General Site Connections 1

2. Anchors 1

3. Guy Cables and Connections 2

4. Tower Foundations 2

5. Tower Structure 2

6. Waveguide/Coax Ice Bridge & Entry Point 3

7. Climbing 3

8. Grounding 3

9. Antennas Bridge & Entry Point 3

10. Waveguide Supports 4

11. FAA Required Lighting 4

12. Tower Paint/Galvanizing 4 Tables 5 Explanation of Bolt Torque Check 6 Hardware Standards Used 7 Guy Wire Tensions 8 Tower Plumb Check 9 Distance From Tower Anchors to Tower Leg 9

DEFINITION OF TERMINOLOGY

EXPLANATION OF COLUMN HEADINGS:

EMERGENCY: ITEM JUDGED TO HAVE A DEFICIENCY REQUIRING IMMEDIATE ATTENTION. FAILURE TO REPAIR THIS DEFICIENCY MAY RESULT IN TOWER FAILURE, PROPERTY DAMAGE, OR INJURY TO

PERSONEL ON THE TOWER AND GROUND.

OFF AIR: ITEM JUDGED TO HAVE A DEFICIENCY REQUIRING IMMEDIATE ATTENTION. FAILURE TO

REPAIR THIS DEFICIENCY MAY RESULT IN LOSS OF AIRTIME.

SAFETY: ITEM JUDGED TO HAVE A SAFETY DEFICIENCY REQUIRING IMMEDIATE ATTENTION. FAILURE TO REPAIR THIS DEFICIENCY MAY RESULT IN PHYSICAL HARM TO PERSONEL ON THE TOWER AND

GROUND.

ROUTINE: ITEM WAS JUDGED TO HAVE A DEFICIENCY THAT REQUIRES IMMEDIATE ATTENTION.

FAILURE TO REPAIR THIS DEFICIENCY MAY ESCALATE INTO A SAFETY, EMERGENCY, OR OFF AIR

CONDITION.

THE CRITERIA USED IN MAKING OUR RECOMMENDATIONS AND OBSERVATIONS ARE BASED ON

THE FOUR LEVLS OF PRIORITY:

FIRST: "KEEP THE TOWER STANDING". THESE ARE STRUCTURAL INTEGRITY ITEMS THAT AFFECT THE

STABILITY OF THE TOWER.

SECOND: "AVOID OFF AIR / DOWN TIME". THESE ARE SYSTEM INTEGRITY ITEMS, WHICH CAN AFFECT

THE SIGNAL OR ABILITY TO REMAIN ON-AIR.

THIRD: "AVOID LIABILITY RISK". THESE ARE LIABILITY RISK ITEMS SUCH AS HAZARDS TO CLIMBERS OR

PERSONS AT OR AROUND THE STRUCTURE, INCLUDING "ATTRACTIVE NUISANCE" POTENTIALS.

FOURTH: "KEEP THE COST OF OWNERSHIP AS LOW AS PRACTICAL". THROUGH APPROPRIATE

MAINTENANCE AND PREVENTATIVE MAINTENANCE, THE UTILITY VALUE OF THE STRUCTURE CAN BE

MAXIMIZED AND THE COST MINIMIZED.

Emergency Repair Work Section Description of Emergency Repair

2E Anchors Not Lined Up Properly With Tower Legs And Center. We Recommend Furnishing And Installing New Anchor(S) And Relocating Existing Wires To The Anchors.

3O Guy Wires Not Properly Tensioned. As Soon As Possible Guy Wires Should Be Re-Tensioned.

5D Bent/Rusty/Damaged Diagonal(S). This Significantly Reduces The Strength Of The Tower. We Recommend Repairing.

7B Safety Climb Device Is Rusty. Rust Can Cause The Safety Climb To Deteriorate. We Recommend Furnishing And Installing A New Safety Climb Device.

Safety Repair Work Section Safety

1H Large Trees Growing Within Falling Distance Of Tower. These Trees Could Fall Resulting In A Potential Tower Collapse. We Recommend That A Local Contractor Be Contacted.

1I Tower Site Does Not Have RF Radiation Warning And/Or High Voltage Broadcast Equipment Signs Posted. We Recommend Furnishing And Installing Signs.

3E Rusty Cotter Pins. These Pins Serve To Secure The Turnbuckles To The Fan Plate, Which Is The Weakest Link In Your Guy Wire System. We Recommend Replacing All Rusty Cotter Pins With Stainless Steel Cotter Pins.

4A Concrete Foundation Not Sealed. We Recommend Applying A Waterproof Sealer To Prevent Water From Entering And Causing Deterioration To The Foundation.

11N There Is No FAA Alarm Controller On Tower. We Recommend To Furnish And Install A FAA Alarm Controller Or Alarm Contacts.

11B Lenses have cracks, UV Damage, Hazing Or Excessive Dirt Buildup. We Recommend Lenses Be Cleaned Or Replaced.

Off Air Repair Work Section Off Air Repair Work 8B Anchor Heads Are Not Grounded. We Recommend Furnishing And Installing Grounding.

8D Waveguide/Ice Bridge Not Properly Grounded And/Or Has Broken Grounding. We Recommend Furnishing And Installing Grounding.

8E Waveguide/Coax Not Properly Grounded At Top And Bottom Of Run. We Recommend Furnishing And Installing Grounding.

8F Missing Buss Bars. We Recommend Furnishing And Installing Buss Bars.

8K Perimeter Fence Not Grounded And/Or Has Broken Grounding. We Recommend Furnishing And Installing Grounding.

10E Chafing/Worn Feedline. We Recommend Weather Proofing And Properly Securing The Coax.

Routine Repair Work Section Routine

1B Access Road Not Readily Accessible To Tower Site(Due To Weeds, Brush, Potholes, Mud, Water, Etc.). We Recommend To Repair The Access Road.

1G Weeds, Trees And/Or Brush Growing Around The Tower Base. We Recommend To Clear Away All Weeds, Trees And/Or Brush Away From The Tower Base.

1G Weeds, Trees And/Or Brush Growing Inside The Perimeter Fence. We Recommend To Clear Away All Weeds, Trees And/Or Brush Away From The Fence.

1G Weeds Growing Around Anchor Heads. This Can Cause Deterioration Of Anchor Heads And Guy Wire Hardware. We Recommend All Weeds Be Cleared Away From The Anchor Heads.

1G Weeds, Trees And/Or Brush Growing Around The Guy Wire. We Recommend To Clear Away All Weeds, Trees And/Or Brush Away From The Guy Wire.

2C Anchor(S) Below Grade. We Recommend Excavating Around The Anchor For Positive Drainage And/Or Replacing The Anchor(S) If Found To Be Necessary.

3I Dead Ends Of Cables Not Secured Properly. We Recommend Properly Securing The Cables By Furnishing And Installing Tie Wires To Prevent Unraveling.

Work Required Within 3 to 5 Years Perform and annual Inspection report.

Check to see if bolts are of proper torque value.

Retention safety climb device (if applicable).

Re-lamp tower (if applicable).

Clean and paint.

Recommendations Concluded We also recommend our annual maintenance agreement to ensure the tower is maintained on a yearly basis. As ample maintenance agreement is enclosed. This report and comments reflect the general condition of the tower on the date of inspection.

Recommendations listed on the preceding pages may be incorporated into a 3-5 year program. If so, the price does not include the additional repair of latent defects if found during this work. If latent defects are found, Allstate Tower INC. will submit a lump-sum bid to the owner to perform the necessary additional repairs. Under no circumstances will the additional repair work be done without owner's written authorization in the form of a separate repair contract agreed to by both parties. Owner agrees to undertake all measures necessary to expedite decisions regarding repairs and avoid delaying the work outlined under the terms of the contract. We recommend $5,000 be set aside for latent defects.

Handling, removing, and/or disposal of hazardous or contaminated material (asbestos, lead, or any substance requiring special handling) are not include in any price submitted or work Herein.

STATED HEIGHTS ARE APPROXIMATE

FOR PURPOSES OF REPAIR ONLY. THESE

STATED VALUES MAY NOT CORRESPOND

EXACTLY TO OFFICIAL HEIGHT.

Tower Inspection Report

JOB NO: IN-078128 INSPECTION DATE: 2019-04-08

CUSTOMER: A&T Systems INSPECTOR: 1 SITE NAME: RANGE CONTROL WEATHER Clear STATE: MO WIND: Mild TOWER TYPE Guyed TEMPERATURE: 70

HEIGHT: 260' LATITUDE: N37.6833036

MANUFACTURER Unknown LONGITUDE: W-92.152546

TOP WIDTH 18" BOTTOM WIDTH: 18"

Section 1 - General Site Conditions A. Is tower reliable for complete survey? Satisfactory B. Access road in good condition? Routine Repair Work C. Tower and Building area are secure (adequate fence, gates, locks)? Satisfactory D. Site is draining properly? Satisfactory E. Equipment Shelter in good condition? Satisfactory F. Condition of equipment on site in good condition (Generator, Fuel Tank)? Satisfactory G. Fence, tower, guy anchors, guy wires. entry port, waveguide/ice bridge clear of vines or vegetation growing on them and no weeds growing inside of fence? Routine Repair Work

H. Tower or guy cables clear of any large trees within falling distance? Safety Repair Work I. RF radiation warning signs, fcc signs, and/or dangerous high voltage broadcast equipment signs in accordance with fcc requirements? Safety Repair Work

J. Tower free of excessive birds roosting? Satisfactory

Section 2 - Anchors A. Guy Anchors Protected From Vehicle, Farm Machinery, And Cattle Damage? Satisfactory B. Anchor location are readily accessible to maintenance crew? Satisfactory C. Anchor heads are above grade and free of twist? Routine Repair Work D. Anchor heads/rods/shaft are free of rust, corrsion and damage? Satisfactory E. Anchors line up properly with tower legs? Emergency Work F. Cathodic protection has been installed on anchors? Satisfactory G. Anchors free of cracking/spalling or evidence of movement? Satisfactory H. Proper drainage and anchors free from erosion? Satisfactory

Section 3 - Guy Cables and Connections A. Turnbuckles free of (rust, corrosion, and deformities)? Satisfactory B. Turnbuckles are of proper size and adjustable in either direction? Satisfactory C. Turnbuckles distributed evenly to fan plate? Satisfactory D. Turnbuckle safety cables adequately sized and properly installed in a figure 8 formation? Satisfactory

E. Cotter pins in place, secure, and free of rust? Safety Repair Work F. Guy thimbles of proper size, installed correctly and free of rust and corrosion Satisfactory G. Cables clamps installed correctly, evenly spaced, and properly torqued and free of rust and corrosion? Satisfactory

H. Cable ends properly project from pre-formed dead end grips? Satisfactory I. Dead ends of cables are of proper length and secured to prevent unraveling? Routine Repair Work J. Guy cables free from splices, strands fractures or rust? Satisfactory K. Guy cables free from kinks/deformities? Satisfactory L. U-bolt(s) are installed correctly on dead side of cable, evenly spaced, properly torqued and free of rust and corrosion? N/A M. Preform guy grips at anchors, pull-offs have safety end sleeves are adequately installed and free of rust? N/A

N. Guy insulators appear to be in good condition? N/A O. Guy wires properly tensioned Emergency P. Are guy wires at pull-offs attached with proper hardware? Satisfactory Q. Does tower have proper pull-off points? Satisfactory

R. Do guy wires have a protective coating on wire sizes ¾" and larger? N/A

S. Are yellow guy markers present? N/A

Section 4 - Tower Foundations A. Concrete foundation above grade, in good condition, no cracking/spalling and properly sealed? Safety Repair Work

B. Grouting under tower legs properly installed?

N/A

Section 5 - Tower Structure A. Tower legs correctly line with tower center and appropriate anchors? Satisfactory B. Visual check indicates tower is plumb and free of twist? Satisfactory C. All structural members installed correctly with no missing members? Satisfactory D. Members and attachments are in good condition (no bent, broken, or otherwise damaged members or attachments)? Emergency Work

E. Structural bolts installed correctly with proper torque and locking devices? Satisfactory F. Welds conform to standards? Satisfactory G. Flange plates free of gap and achieving 50% load bearing? Satisfactory

H. Weep holes are unobstructed? N/A

I. Are tower legs capped? N/A J. Check indicates tower legs free of damage? Satisfactory

Section 6 - Waveguide/Coax Ice Bridge and Entry Port A. Waveguide/Ice Bridge provides adequate line protection? Satisfactory

B. Waveguide/Ice Bridge line hangers are installed correctly, securely and evenly spaced? Satisfactory C. Waveguide/coax entry port hole covers in good condition? Satisfactory D. Waveguide/coax lines properly installed and sealed with boot hardware? Satisfactory

Section 7 - Climbing Apparatus A. Tower has OSHA-approved safety climb device installed? Satisfactory B. Safety climb device properly installed, free of rust, and in good working condition? Emergency Work C. All ladder splices complete and sections firmly attached to tower? Satisfactory D. All climbing hardware is properly installed and rust free?

E. All ladder rungs or climbing pegs are present and in good condition? Satisfactory

F. Tower is protected by anti-climb device?

N/A

Section 8 - Grounding A. Individual guy cables are properly grounded? Satisfactory B. Anchor head plates or shafts are grounded? Off Air Work C. Tower base is properly grounded? Satisfactory D. Waveguide/ice bridge is properly grounded? Off Air Work E. Waveguide/coax properly grounded to bus bar, down conductor, and at every 200 ft? Off Air Work F. Are bus bars installed correctly? Off Air Work G. Waveguide/coax properly grounded at building port entry? Satisfactory H. Ground wires routed in downward direction with no sharp bends? Satisfactory I. Hoisting grip installed below upper ground kit? Satisfactory

J. Tower has proper lightning protection, down conductor, and is properly installed?

N/A

K. Fence is properly grounded? Off Air Work

Section 9 - Antennas A. Antennas or antenna components are in good condition? Satisfactory B. Hardware is present and free from rust? Satisfactory C. All stiff-arm tiebacks are properly connected to antenna and tower? Satisfactory

D. All appropriate feed horn guy spring hangers properly in place?

N/A

E. Radomes covers are present and free from any cracks or tears?

N/A

F. Antenna mount structural members appear adequate and secure? Satisfactory G. All tower lines and antenna(s)/equipment are in use? Satisfactory

Section 10 - Waveguides A. Line to feed connection secure with no excessive movement allowed? Satisfactory B. Line to feed connection is free from excessive bends or twists? Satisfactory C. All lines run straight with drip loops, end connections weatherproofed and in good condition? Satisfactory

D. All waveguide/coax runs supported at proper intervals? Satisfactory E. Line protective coating if "tied" to tower members is free from chafing? Off Air Work F. All lines properly supported at top with hoisting grips that are in good condition and properly attached? Satisfactory

G. Feedline is free from any visible air leaks?

N/A

Section 11 - FAA Required Lighting A. Is lighting system updated and in compliance with current FAA/FCC standards. Satisfactory B. Beacon, obstruction light, and strobe unit glass are free from any cracks or breaks?

C. Are lamp units clean with wires, terminals, and sockets corrosion free? Satisfactory D. Lamp unit closure bolts or spring fasteners functioning properly and free of rust? Satisfactory E. Beacon or strobe unit cord in good condition and unit cord drip loop not rubbing on tower members?

F. Obstruction lights correctly positioned and properly secured to tower? Satisfactory

G. Conduit supported at max. 8 ft. Intervals and all joints tight, free of rust and breathers clear and clean? N/A H. Wire correctly installed over wire supports in junction boxes and terminal blocks tight and free of corrosion?

I. Junction box terminals tight and free of corrosion?

J. Photocell positioned so that it has unobstructed view of the north sky? Satisfactory K. All lights functional? Satisfactory

M. Approved light monitoring device or site component installed?

N/A

N. Does current light system have a FAA approved alarm controller? Safety Repair Work

Section 12 - Tower Paint/Galvanizing A. Tower paint/galvanizing is free from fading, chipping, peeling or general failure? Satisfactory

B. If required, proper FAA approved colors and banding? N/A

C. Paint visually effective as warning to aircraft?

N/A

D. Feed Lines Properly Branded?

N/A

Safety Repair Work

Explanation of Bolt Torque Check Structural bolt connections are "sampled" at the rate of at least 10 bolts per each 20 vertical feet of tower height. The tower is considered to be in acceptable condition if the number of under-torqued bolts is found to be no more than 5% of the total sampled.

The tower is said to have a "maintenance deficiency" if the number of under-torqued bolts is 6% to 30% of the total sampled. If this is the case, the tower should be re-checked, at least annually. Since each under-torqued bolt found during the random sampling process is re-tightened to the proper level, the number of under-torqued bolts will eventually drop back below the structurally acceptable condition and all bolts should be checked and re-tightened to correct levels.

The controlling bolt torque values used are:

Hardware Standards Used:

Guy Tensions Size Type Anchor Location Guy Elevation Required Tension Actual Tension ehs A 62' 1200 1/4" ehs B 62' 552.0 - 674.6 1200 1/4" ehs C 62' 551.9 - 674.5 1200 1/4" ehs A 124' 561.7 - 686.5 1100 1/4" ehs B 124' 561.9 - 686.7 1100 1/4" ehs C 124' 561.7 - 686.5 1100 5/16" ehs A 186' 961.3 - 1174.9 1120 5/16" ehs B 186' 961.7 - 1175.5 1120 5/16" ehs C 186' 961.3 - 1174.9 1120 5/16" ehs A 247' 973.5 - 1189.9 1120 5/16" ehs B 247' 974.0 - 1190.4 1120 5/16" ehs C 247' 973.5 - 1189.9 1120

551.9 - 674.51/4"

Tower Plumb Guy Sighting A Sighting B Sighting C Level Left Right Left Right Left Right

Initial Final Initial Final Initial Final Inital Final Initial Final Initial Final Bottom 0 0 1/4 1/4" 1/4 2nd 3" 3" 1.1/2" 1.1/2" 3rd 3" 3" 2" 2" 4th 3" 3" 4" 4" 5th 6th 7th 8th 9th 10th

DISTANCE FROM TOWER ANCHORS TO TOWER LEG

Anchor: A B C D Inner:

Middle:

Outer

Tower Loading and Specifics

Customer Status Mount Height

# of Antennas

# of Sectors

Antenna Make/Model

Total # of Lines

Lines Size Tower Azimuth

Mount Type

Field Notes

A&T Systems active 135' 1 6' Low Band

Two-way 1 7/8_heliax 42 leg C

A&T Systems active 212' 1 20' Whip Two-way 1 7/8_heliax 45 leg C

A&T Systems active 241' 1 15' Whip Two-way 1 7/8_heliax 45 leg C

Section 1 Photos

Routine:

B. Access Road Not Readily Accessible To Tower Site(Due To Weeds, Brush, Potholes, Mud, Water, Etc.). We Recommend To Repair The Access Road.

Routine:

G. Weeds, Trees And/Or Brush Growing Around The Tower Base.

We Recommend To Clear Away All Weeds, Trees And/Or Brush Away From The Tower Base.

G. Weeds, Trees And/Or Brush Growing Inside The Perimeter Fence. We Recommend To Clear Away All Weeds, Trees And/Or Brush Away From The Fence.

Routine:

G. Weeds, Trees And/Or Brush Growing Inside The Perimeter Fence. We Recommend To Clear Away All Weeds, Trees And/Or Brush Away

Fence.

G. Weeds Growing Around Anchor Heads. This Can Cause Deterioration Of Anchor Heads And Guy Wire Hardware.

We Recommend All Weeds Be Cleared Away From The Anchor Heads.

Routine:

G. Weeds Growing Around Anchor Heads. This Can Cause Deterioration Of Anchor Heads And Guy Wire Hardware.

We Recommend All Weeds Be Cleared Away From The Anchor Heads.

Growing Around Anchor Heads. This Can Cause Deterioration Of Anchor Heads And Guy Wire Hardware.

We Recommend All Weeds Be Cleared Away From The Anchor Heads.

Routine:

G. Weeds Growing Around Anchor Heads. This Can Cause Deterioration Of Anchor Heads And Guy Wire Hardware.

We Recommend All Weeds Be Cleared Away From The

Growing Around Anchor Heads. This Can Cause Deterioration Of Anchor Heads And Guy Wire Hardware.

We Recommend All Weeds Be Cleared Away From The Anchor Heads.

Routine:

G. Weeds Growing Around Anchor Heads. This Can Cause Deterioration Of Anchor Heads And Guy Wire Hardware.

We Recommend All Weeds Be Cleared Away From The

Growing Around Anchor Heads. This Can Cause Deterioration Of Anchor Heads And Guy Wire Hardware.

We Recommend All Weeds Be Cleared Away From The Anchor Heads.

Routine:

G. Weeds Growing Around Anchor Heads. This Can Cause Deterioration Of Anchor Heads And Guy Wire Hardware.

We Recommend All Weeds Be Cleared Away From The

Growing Around Anchor Heads. This Can Cause Deterioration Of Anchor Heads And Guy Wire Hardware.

We Recommend All Weeds Be Cleared Away From The Anchor Heads.

Routine:

G. Weeds, Trees And/Or Brush Growing Around The Guy Wire.

We Recommend To Clear Away All Weeds, Trees And/Or Brush Away

Guy Wire.

Safety:

H. Large Trees Growing Within Falling Distance Of Tower.

These Trees Could Fall Resulting In A Potential Tower Collapse.

We Recommend That A Local Contractor Be Contacted.

Safety:

I. Tower Site Does Not Have

RF

Radiation Warning And/Or High Voltage Broadcast Equipment Signs Posted. We Recommend Furnishing And Installing Signs.

I. Tower Site Does Not Have

RF

Radiation Warning And/Or High Voltage Broadcast Equipment Signs Posted. We Recommend Furnishing And Installing Signs.

Access Road

Entrance and Compound

Section 2 Photos

Routine:

C.

Anchor(S) Below Grade. We Recommend Excavating Around The Anchor For Positive Drainage And/Or Replacing The Anchor(S) If Found To Be Necessary.

A

C.

Anchor(S) Below Grade. We Recommend Excavating Around The Anchor For Positive Drainage And/Or Replacing The Anchor(S) If Found To Be Necessary.

B

Routine:

C.

Anchor(S) Below Grade. We Recommend Excavating Around The Anchor For Positive Drainage And/Or Replacing The Anchor(S) If Found To Be Necessary.

C

Emergency:

E. Anchors Not Lined Up Properly With Tower Legs And Center. We Recommend Furnishing And Installing New Anchor(S) And Relocating Existing Wires To The Anchors.

Emergency:

E. Anchors Not Lined Up Properly With Tower Legs And Center. We Recommend Furnishing And Installing New Anchor(S) And Relocating Existing Wires To The Anchors.

E. Anchors Not Lined Up Properly With Tower Legs And Center. We Recommend Furnishing And Installing New Anchor(S) And Relocating Existing Wires To The Anchors.

Anchors

Anchor A Normal surface rust.

B

C

E. Rusty Cotter Pins.

These Pins Serve To Secure The Turnbuckles To The Fan Plate, Which Is The Weakest Link In Your Guy Wire System. We Recommend Replacing All Rusty Cotter Pins With Stainless Steel Cotter Pins. Tower

Safety:

E. Rusty Cotter Pins.

These Pins Serve To Secure The Turnbuckles To The Fan Plate, Which Is The Weakest Link In Your Guy Wire System. We Recommend Replacing All Rusty Cotter Pins With Stainless Steel Cotter Pins.

Section 3 Photos

E. Rusty Cotter Pins.

These Pins Serve To Secure The Turnbuckles To The Fan Plate, Which Is The Weakest Link In Your Guy Wire System. We Recommend Replacing All Rusty Cotter Pins With Stainless Steel Cotter Pins.

Safety:

E. Rusty Cotter Pins.

These Pins Serve To Secure The Turnbuckles To The Fan Plate, Which Is The Weakest Link In Your Guy Wire System. We Recommend Replacing All Rusty Cotter Pins With Stainless Steel Cotter Pins.

I. Dead Ends Of Cables Not Secured Properly.

We Recommend Properly Securing The Cables By Furnishing And Installing Tie Wires To Prevent Unraveling.

Routine:

I. Dead Ends Of Cables Not Secured Properly.

We Recommend Properly Securing The Cables By Furnishing And Installing Tie Wires To Prevent Unraveling.

I. Dead Ends Of Cables Not Secured Properly.

We Recommend Properly Securing The Cables By Furnishing And Installing Tie Wires To Prevent Unraveling.

Routine:

I. Dead Ends Of Cables Not Secured Properly.

We Recommend Properly Securing The Cables By Furnishing And Installing Tie Wires To Prevent Unraveling.

O. Guy Wires Not Properly Tensioned. As Soon As Possible Guy Wires Should Be Re- Tensioned.

Section 4 Photos

Safety:

A. Concrete Foundation Not Sealed.

We Recommend Applying A Waterproof Sealer To Prevent Water From Entering And Causing Deterioration To The Foundation.

Foundation

- Tower Base

Foundation

Base

Foundation

Base

Section 5 Photos

Emergency:

D.

Bent/Rusty/Damaged Diagonal(S). This Significantly Reduces The Strength Of The Tower. We Recommend Repairing. Face A 250' Bent member.

Entry Port

Waveguide Ice Bridge

Entry Port and Waveguide Ice Bridge

Section 6 Photos

Feed Lines

Section 7 Photos

A. Safety- Climb Device.

A. Safety-

Device.

A. Safety-

A. Safety-

Device.

Emergency:

B. Safety Climb Device Is Rusty. Rust Can Cause The Safety Climb To Deteriorate.

We Recommend Furnishing And Installing A New Safety

B. Safety Climb Device Is Rusty. Rust Can Cause The Safety Climb To Deteriorate.

We Recommend Furnishing And Installing A New Safety Climb Device.

Emergency:

B. Safety Climb Device Is Rusty. Rust Can Cause The Safety Climb To Deteriorate.

We Recommend Furnishing And Installing A New Safety

Off Air:

B. Anchor Heads Are Not Grounded.

We Recommend Furnishing And Installing Grounding.

Off Air:

B. Anchor Heads Are Not Grounded.

We Recommend Furnishing And Installing Grounding.

Section 8 Photos

B. Anchor Heads Are Not Grounded.

We Recommend Furnishing And Installing Grounding.

Off Air:

D.

Waveguide/Ice Bridge Not Properly Grounded And/Or Has Broken Grounding.

We Recommend Furnishing And Installing

E. Waveguide/Coax Not Properly Grounded At Top And Bottom Of Run. We Recommend Furnishing And Installing Grounding.

Off Air:

F. Missing Buss Bars.

We Recommend Furnishing And

Buss Bars.

F. Missing Buss Bars.

We Recommend Furnishing And Installing Buss Bars.

Off Air:

F. Missing Buss Bars.

We Recommend Furnishing And

Buss Bars.

We Recommend Furnishing And Installing Buss Bars.

Off Air:

F. Missing Buss Bars.

We Recommend Furnishing And

Buss Bars.

We Recommend Furnishing And Installing Buss Bars.

Off Air:

F. Missing Buss Bars.

We Recommend Furnishing And

K.

Perimeter Fence Not Grounded And/Or Has Broken Grounding.

We Recommend Furnishing And Installing Grounding.

Off Air:

K.

Perimeter Fence Not Grounded And/Or Has Broken Grounding.

We Recommend Furnishing And

Perimeter Fence Not Grounded And/Or Has Broken Grounding.

We Recommend Furnishing And Installing Grounding.

Off Air:

K.

Perimeter Fence Not Grounded And/Or Has Broken Grounding.

We Recommend Furnishing And

Perimeter Fence Not Grounded And/Or Has Broken Grounding.

We Recommend Furnishing And Installing Grounding.

Section 9 Photos

Antennas

Mounts

Antennas

Mounts

Antennas

Mounts

E.

Chafing/Worn Feedline. We Recommend Weather Proofing And Properly Securing The Coax. 241'

Section 11 Photos

Safety:

O. There Is No FAA Alarm Controller On Tower.

We Recommend To Furnish And Install

A FAA

Alarm Controller Or Alarm Contacts.

Section 10 Photos

Light

Top Light

Top Light

Lightning Rod

Safety:

B. Lenses have cracks, UV Damage, Hazing Or Excessive Dirt Buildup. We Recommend Lenses Be Cleaned Or Replaced.

View Down

View Down

Blank Page