Addendum 3.pdf

130th Airlift Wing SUMMARY OF CHANGES TO SPECIFICATIONS – ADDENDUM 3 West Virginia Air National Guard Fuel System/Corrosion Control Hangar and Shops Yeager Airport, Charleston, West Virginia LYBH009134

The Benham Companies, LLC 1 of 1 August 25, 2009

Specification Section Change

1. Table of Contents Updated to reflect addition of Specification Section 10461

FIRE EXTINGUISHERS

2. 10461 FIRE EXTINGUISHERS Added this section in its entirety.

END OF CHANGES

Fuel System/Corrosion Control Hangar & Shops LYBH009134 WV National Guard, 130th Airlift Wing, Charleston, WV ADDENDUM 3

PROJECT TABLE OF CONTENTS

DIVISION 01 - GENERAL REQUIREMENTS

01001 AFFIRMATIVE PROCUREMENT

01330 GENERAL REQUIREMENTS

01332 LEED® DOCUMENTATION

01335 ENVIRONMENTAL PROTECTION

01572 CONSTRUCTION AND DEMOLITION WASTE MANAGEMENT

01575N TEMPORARY ENVIRONMENTAL CONTROLS

01670 RECYCLED / RECOVERED MATERIALS

01781 OPERATION AND MAINTENANCE DATA

01910 COMMISSIONING

DIVISION 02 - SITE CONSTRUCTION

02220S DEMOLITION

02231 CLEARING AND GRUBBING

02300S EARTHWORK

02390 MOORING AND GROUNDING POINTS FOR AIRCRAFT

02510 WATER DISTRIBUTION

02531S SANITARY SEWERS

02549 PREFABRICATED UNDERGROUND COOLING DISTRIBUTION SYSTEM

02556A GAS DISTRIBUTION SYSTEM

02582 ELECTRICAL HANDHOLES AND MANHOLES

02630 STORM DRAINAGE

02705 BASE COURSE FOR RIGID AND SUBBASES FOR FLEXIBLE PAVING

02742 HOT MIX BITUMINOUS PAVEMENT

02751 AIRFIELDS AND HEAVY-DUTY CONCRETE PAVEMENT LESS THAN

10000 CUBIC YARDS

02762 COMPRESSION JOINT SEALS FOR CONCRETE PAVEMENTS

02770 CONCRETE SIDEWALKS AND CURBS AND GUTTERS

02825S CHAIN LINK FENCES AND GATES

02921 SEEDING

02930 EXTERIOR PLANTS

02935 LANDSCAPE ESTABLISHMENT

DIVISION 03 - CONCRETE

03100A STRUCTURAL CONCRETE FORMWORK

03150A EXPANSION JOINTS, CONTRACTION JOINTS, AND WATERSTOPS

03200A CONCRETE REINFORCEMENT

03300A CAST-IN-PLACE CONCRETE

DIVISION 04 - MASONRY

04200 MASONRY

DIVISION 05 - METALS

05120 STRUCTURAL STEEL

05211 LONGSPAN STEEL JOIST FRAMING

05310 STEEL DECKS

05500 METAL: MISCELLANEOUS AND FABRICATIONS

DIVISION 06 - WOOD AND PLASTICS

06100 ROUGH CARPENTRY

06200 FINISH CARPENTRY

PROJECT TABLE OF CONTENTS Page 1

06603 PLASTIC-FACED WALL PANELS

06611 SOLID POLYMER (SOLID SURFACING) FABRICATIONS

DIVISION 07 - THERMAL AND MOISTURE PROTECTION

07190 WATER REPELLENTS

07211 PERIMETER WALL INSULATION

07600 FLASHING AND SHEET METAL

07611N STEEL STANDING SEAM ROOFING

07720 ROOF ACCESSORIES

07840 FIRESTOPPING

07920 JOINT SEALANTS

DIVISION 08 - DOORS AND WINDOWS

08110 STEEL DOORS AND FRAMES

08210 WOOD DOORS

08331S OVERHEAD COILING DOORS

08347 SOUND CONTROL DOOR ASSEMBLIES

08370 OVERHEAD HOIST-UP FABRIC DOOR

08410 ALUMINUM ENTRANCES AND STOREFRONTS

08565 BLAST RESISTANT ALUMINUM-FRAMED GLASS WINDOWS

08620 SKYLIGHTS

08710 DOOR HARDWARE

08800 GLAZING

08950 INSULATED TRANSLUCENT FIBERGLASS SANDWICH PANEL SYSTEM

DIVISION 09 - FINISHES

09250 GYPSUM BOARD

09310 CERAMIC TILE, QUARRY TILE, AND PAVER TILE

09510 ACOUSTICAL CEILINGS

09611 THIN FILM FLOORING SYSTEM FOR AIRCRAFT MAINTENANCE

FACILITIES

09612 ELECTRICAL GRADE DIELECTRIC SWITCHBOARD MATTING FLOORING

SYSTEM

09650 RESILIENT FLOORING

09680 CARPET

09840 PERFORATED METAL ACOUSTICAL PANEL SYSTEM

09900 PAINTS AND COATINGS

DIVISION 10 - SPECIALTIES

10100 VISUAL COMMUNICATIONS SPECIALTIES

10160S PLASTIC TOILET COMPARTMENTS

10430 EXTERIOR SIGNAGE

10440 INTERIOR SIGNAGE

10461 FIRE EXTINGUISHERS

10500S LOCKERS AND BENCHES

10510 FRONT LOAD SECURED MINI LOCKERS

10800 TOILET ACCESSORIES

DIVISION 11 - EQUIPMENT

11311 PARALLEL PLATE, GRAVITY OIL-WATER SEPARATOR

11312 PACKAGE LIFT STATION

DIVISION 12 - FURNISHINGS

PROJECT TABLE OF CONTENTS Page 2

12350 DISPLAY CASEWORK

12495S HORIZONTAL LOUVER BLINDS

DIVISION 13 - SPECIAL CONSTRUCTION

13100N LIGHTNING PROTECTION SYSTEM

13120 METAL BUILDING SYSTEMS

13700 DOOR CONTROL SYSTEM

13845 LIGHTING CONTROLS

13859 INTERIOR FIRE ALARM, FOAM RELEASING, AND MASS

NOTIFICATION SYSTEM

13921 ELECTRIC-DRIVE HORIZONTAL FIRE PUMPS

13930 WET PIPE SPRINKLER SYSTEM, FIRE PROTECTION

13955 HIGH-EXPANSION FOAM FIRE PROTECTION SYSTEM

DIVISION 14 - CONVEYING SYSTEMS

14240 LIMITED USE/LIMITED APPLICATION ELEVATORS

14605A MONORAILS WITH ELECTRIC, AIR, OR MANUAL POWERED HOIST

DIVISION 15 - MECHANICAL

15003S GENERAL MECHANICAL PROVISIONS

15050S BASIC MECHANICAL MATERIALS AND METHODS

15055S WELDING MECHANICAL

15070N MECHANICAL SOUND AND VIBRATION CONTROL

15080 THERMAL INSULATION FOR MECHANICAL SYSTEMS

15102S PLUMBING

15120S PIPING SPECIALTIES

15135S CENTRIFUGAL PUMPS

15181S CHILLED WATER PIPING SYSTEMS

15185N LOW TEMPERATURE WATER (LTW) HEATING SYSTEM

15190A GAS PIPING SYSTEMS

15211S LOW-PRESSURE COMPRESSED AIR SYSTEMS

15216N WELDING PRESSURE PIPING

15218 BREATHING AIR SYSTEM

15400 PLUMBING, GENERAL PURPOSE

15510S BOILERS

15565A HEATING SYSTEM; GAS-FIRED HEATERS

15620A LIQUID CHILLER

15720N AIR HANDLING UNITS

15764S FAN-COIL UNITS

15766S UNIT HEATERS

15810N DUCTWORK, DUCTWORK ACCESSORIES AND RELATED EQUIPMENT

15839 CEILING MOUNTED AIR MOVING FANS

15840 AIR TERMINAL UNITS

15910N DIRECT DIGITAL CONTROL SYSTEMS

15940A WELDING FUME EXHAUST REMOVAL SYSTEM(S)

15950N HVAC TESTING/ADJUSTING/BALANCING

15995A COMMISSIONING OF HVAC SYSTEMS

DIVISION 16 - ELECTRICAL

16050N BASIC ELECTRICAL MATERIALS AND METHODS

16081 APPARATUS INSPECTION AND TESTING

16135S CABLE TRAYS FOR COMMUNICATIONS SYSTEMS

16261 VARIABLE FREQUENCY DRIVE SYSTEMS UNDER 600 VOLTS

16268 400-HERTZ (HZ) SOLID STATE FREQUENCY CONVERTER

16302N UNDERGROUND TRANSMISSION AND DISTRIBUTION

PROJECT TABLE OF CONTENTS Page 3

16321 SINGLE OPERATION GENERATOR SETS

16402 INTERIOR DISTRIBUTION SYSTEM

16442 SWITCHBOARDS

16510 INTERIOR LIGHTING

16520 EXTERIOR LIGHTING

16710 BUILDING TELECOMMUNICATIONS CABLING SYSTEM

16711 TELECOMMUNICATIONS OUTSIDE PLANT (OSP)

16815A COMMUNITY ANTENNA TELEVISION (CATV) SYSTEMS

-- End of Project Table of Contents --

PROJECT TABLE OF CONTENTS Page 4

SECTION 10461

FIRE EXTINGUISHERS

05/09

PART 1 GENERAL

1.1 REFERENCES

The publications listed below form a part of this specification to the extent referenced. The publications are referred to within the text by the basic designation only.

INTERNATIONAL CODE COUNCIL (ICC)

IFC 906 (2004) Portable Fire Extinguishers

NATIONAL FIRE PROTECTION ASSOCIATION (NFPA)

NFPA 1 (2008) Uniform Fire Code, 2006 Edition

NFPA 10 (2007; Errata 2007; AMD 1 2007) Standard for Portable Fire Extinguishers

NFPA 101 (2008) Life Safety Code, 2006 Edition

NFPA 409 (2004; TIA 2005; TIA 2006) Standard on Aircraft Hangers

U.S. NATIONAL ARCHIVES AND RECORDS ADMINISTRATION (NARA)

29 CFR 1910.106 Flammable and Combustible Liquids

1.2 SUBMITTALS

Government approval is required for submittals with a "G" designation;

submittals not having a "G" designation are for information only. Submit the following in accordance with Section 01330 GENERAL REQUIREMENTS:

SD-01 Preconstruction Submittals

Manufacturer's Data for each type of required Fire Extinguisher with all related details, cabinets, accessories, and recommended operation manuals.

SD-02 Shop Drawings

Submit fabrication drawings for the following items consisting of fabrication and assembly details performed in the factory. Submit installation drawings for the following items in accordance with the paragraph entitled, "Installation," of this section.

Fire Extinguishers; G

Accessories; G

Cabinets; G

SECTION 10461 Page 1

Wall Brackets; G

SD-03 Product Data

Submit Manufacturer's catalog and warranty data for the following items:

Fire Extinguishers; G

Accessories; G

Cabinets; G

Wall Brackets; G

SD-04 Samples

One of each type of Fire Extinguisher being installed

One full-sized sample of each type of Cabinet being installed

Three samples of Wall Brackets and Accessories of each type being used

Approved samples may be used for installation, with proper identification and storage.

SD-07 Certificates

Submit Certificates showing the following:

Certification that Fire Extinguishers comply with local codes and regulations.

Certification that Fire Extinguishers comply with OSHA, NFPA, and UL requirements.

Submit Manufacturer's Warranty with Inspection Tag on each extinguisher.

Guarantee that Fire Extinguishers are free of defects in materials, fabrication, finish, and installation and that they will remain so for a period of not less than one year after completion.

1.3 DELIVERY, HANDLING, AND STORAGE

Protect materials from weather, soil, and damage during delivery, storage, and construction.

Deliver materials in their original packages, containers, or bundles bearing the brand name and the name and type of the material.

PART 2 PRODUCTS

2.1 TYPES

Provide Fire Extinguishers conforming to NFPA 10. Provide quantity and placement in compliance with the applicable sections of IFC 906, NFPA 1, SECTION 10461 Page 2

NFPA 101, NFPA 409, and 29 CFR 1910.106.

Submit Manufacturer's Data for each type of Fire Extinguisher required, detailing all related Cabinet, Wall Mounting and Accessories information, complete with Manufacturer's Warranty with Inspection Tag.

2.2 MATERIAL

Provide corrosion-resistant steel extinguisher shell.

2.3 SIZE

Extinguishers must be 10 pounds.

2.4 ACCESSORIES

Safety release

Pressure gage

2.5 CABINETS

2.5.1 Material

Provide enameled steel cabinets.

2.5.2 Type

Provide recessed type cabinets at locations as indicated on the drawings.

2.5.3 Size

Dimension cabinets to accommodate the specified fire extinguishers as indicated on the drawings.

2.6 WALL BRACKETS

Provide wall-hook fire extinguisher wall brackets at locations as indicated on the drawings.

Provide wall bracket and accessories as approved.

PART 3 EXECUTION

3.1 INSTALLATION

Install Fire Extinguishers where indicated on the drawings. Verify exact locations prior to installation.

Comply with the manufacturer's recommendations for all installations.

Provide extinguishers which are fully charged and ready for operation upon installation. Provide extinguishers complete with Manufacturer's Warranty with Inspection Tag attached.

SECTION 10461 Page 3

3.2 ACCEPTANCE PROVISIONS

3.2.1 Repairing

Remove and replace damaged and unacceptable portions of completed work with new work at no additional cost to the Government.

Provide Replacement Parts list indicating specified items replacement part, replacement cost, and name, address and contact for replacement parts distributor.

3.2.2 Cleaning

Clean all surfaces of the work, and adjacent surfaces which are soiled as a result of the work. Remove from the site all construction equipment, tools, surplus materials and rubbish resulting from the work.

-- End of Section --

SECTION 10461 Page 4

2.6 WALL BRACKETS