18R3013vol2.PDF

Fort Benning, Georgia

Solicitation Number

W912HN-18-R-3013

Flight Control Tower Volume 2 of 4: Specification Divisions 06 - 21

PN 55112

August 2018

U.S. ARMY ENGINEER DISTRICT, SAVANNAH

CORPS OF ENGINEERS

100 WEST OGLETHORPE AVENUE

SAVANNAH, GEORGIA 31401-3640

US Army Corps of Engineers Savannah District

Fl i ght Cont r ol Tower 18R3013 Ft . Benni ng, GA

PROJECT TABLE OF CONTENTS

DI VI SI ON 01 - GENERAL REQUI REMENTS

01 11 00 SUMMARY OF WORK

01 32 01. 00 10 PROJECT SCHEDULE

01 33 00 SUBMI TTAL PROCEDURES

01 33 29 SUSTAI NABI LI TY REPORTI NG

01 35 26 GOVERNMENTAL SAFETY REQUI REMENTS

01 42 00 SOURCES FOR REFERENCE PUBLI CATI ONS

01 45 00. 00 10 QUALI TY CONTROL

01 45 00. 15 10 RESI DENT MANAGEMENT SYSTEM CONTRACTOR MODE( RMS CM)

01 45 35 SPECI AL I NSPECTI ONS

01 50 00 TEMPORARY CONSTRUCTI ON FACI LI TI ES AND CONTROLS

01 57 19 TEMPORARY ENVI RONMENTAL CONTROLS

01 74 19 CONSTRUCTI ON AND DEMOLI TI ON WASTE MANAGEMENT

01 78 00 CLOSEOUT SUBMI TTALS

01 78 23 OPERATI ON AND MAI NTENANCE DATA

01 91 00. 15 TOTAL BUI LDI NG COMMI SSI ONI NG

DI VI SI ON 03 - CONCRETE

03 30 00 CAST- I N- PLACE CONCRETE

DI VI SI ON 04 - MASONRY

04 20 00 UNI T MASONRY

DI VI SI ON 05 - METALS

05 05 23. 16 STRUCTURAL WELDI NG

05 12 00 STRUCTURAL STEEL

05 21 00 STEEL JOI ST FRAMI NG

05 30 00 STEEL DECKS

05 40 00 COLD- FORMED METAL FRAMI NG

05 50 13 MI SCELLANEOUS METAL FABRI CATI ONS

05 51 00 METAL STAI RS

DI VI SI ON 06 - WOOD, PLASTI CS, AND COMPOSI TES

06 10 00 ROUGH CARPENTRY

06 20 00 FI NI SH CARPENTRY

06 41 16. 00 10 PLASTI C- LAMI NATE- CLAD ARCHI TECTURAL CABI NETS

06 61 16 SOLI D SURFACI NG FABRI CATI ONS

DI VI SI ON 07 - THERMAL AND MOI STURE PROTECTI ON

07 05 23 PRESSURE TESTI NG AN AI R BARRI ER SYSTEM FOR AI R TI GHTNESS

07 13 53 ELASTOMERI C SHEET WATERPROOFI NG

07 21 13 BOARD AND BLOCK I NSULATI ON

07 21 16 MI NERAL FI BER BLANKET I NSULATI ON

07 22 00 ROOF AND DECK I NSULATI ON

07 27 10. 00 10 BUI LDI NG AI R BARRI ER SYSTEM

07 27 19. 01 SELF- ADHERI NG AI R BARRI ERS

07 27 26 FLUI D- APPLI ED MEMBRANE AI R BARRI ERS

07 41 63 FABRI CATED ROOF PANEL ASSEMBLI ES

07 42 13 METAL WALL PANELS

07 57 13 SPRAYED POLYURETHANE FOAM ( SPF) ROOFI NG

07 60 00 FLASHI NG AND SHEET METAL

PROJECT TABLE OF CONTENTS Page 1

07 84 00 FIRESTOPPING

07 92 00 JOI NT SEALANTS

DI VI SI ON 08 - OPENI NGS

08 11 13 STEEL DOORS AND FRAMES

08 14 00 WOOD DOORS

08 44 00 CURTAI N WALL AND GLAZED ASSEMBLI ES

08 71 00 DOOR HARDWARE

08 81 00 GLAZING

08 88 58 AI R TRAFFI C CONTROL TOWER CAB GLASS

08 91 00 METAL WALL AND DOOR LOUVERS

DI VI SI ON 09 - FI NI SHES

09 06 00 SCHEDULES FOR FI NI SHES

09 22 00 SUPPORTS FOR PLASTER AND GYPSUM BOARD

09 29 00 GYPSUM BOARD

09 30 10 CERAMI C, QUARRY, AND GLASS TI LI NG

09 51 00 ACOUSTI CAL CEI LI NGS

09 65 00 RESI LI ENT FLOORI NG

09 67 23. 13 STANDARD RESI NOUS FLOORI NG

09 69 13 RI GI D GRI D ACCESS FLOORI NG

09 90 00 PAI NTS AND COATI NGS

DI VI SI ON 10 - SPECI ALTI ES

10 14 00. 10 EXTERI OR SI GNAGE

10 14 00. 20 I NTERI OR SI GNAGE

10 26 00 WALL PROTECTI ON

10 28 13 TOI LET ACCESSORI ES

10 44 43. 00 37 FI RE EXTI NGUI SHER ACCESSORI ES

10 51 13 METAL LOCKERS

DI VI SI ON 12 - FURNI SHI NGS

12 24 13 ROLLER WI NDOW SHADES

12 35 13. 00 37 AI R TRAFFI C CONTROL CASEWORK

12 48 13 ENTRANCE FLOOR MATS AND FRAMES

DI VI SI ON 13 - SPECI AL CONSTRUCTI ON

13 48 00 SEI SMI C PROTECTI ON FOR MI SCELLANEOUS EQUI PMENT

13 48 00. 00 10 SEI SMI C PROTECTI ON FOR MECHANI CAL EQUI PMENT

DI VI SI ON 14 - CONVEYI NG EQUI PMENT

14 21 23 ELECTRI C TRACTI ON PASSENGER ELEVATORS

DI VI SI ON 21 - FI RE SUPPRESSI ON

21 12 00 STANDPI PE SYSTEMS

21 13 13. 00 10 WET PI PE SPRI NKLER SYSTEM, FI RE PROTECTI ON

21 30 00 FI RE PUMPS

DI VI SI ON 22 - PLUMBI NG

22 00 00 PLUMBI NG, GENERAL PURPOSE

PROJECT TABLE OF CONTENTS Page 2

DI VI SI ON 23 - HEATI NG, VENTI LATI NG, AND AI R CONDI TI ONI NG ( HVAC)

23 00 00 AI R SUPPLY, DI STRI BUTI ON, VENTI LATI ON, AND EXHAUST SYSTEMS

23 05 93 TESTI NG, ADJUSTI NG, AND BALANCI NG FOR HVAC

23 07 00 THERMAL I NSULATI ON FOR MECHANI CAL SYSTEMS

23 09 00 I NSTRUMENTATI ON AND CONTROL FOR HVAC

23 09 13 I NSTRUMENTATI ON AND CONTROL DEVI CES FOR HVAC

23 09 23. 01 LONWORKS DI RECT DI GI TAL CONTROL FOR HVAC AND OTHER

BUI LDI NG CONTROL SYSTEMS

23 11 25 FACI LI TY GAS PI PI NG

23 23 00 REFRI GERANT PI PI NG

23 52 00 HEATI NG BOI LERS

23 57 10. 00 10 FORCED HOT WATER HEATI NG SYSTEMS USI NG WATER AND STEAM

HEAT EXCHANGERS

23 64 10 WATER CHI LLERS, VAPOR COMPRESSI ON TYPE

23 64 26 CHI LLED, CHI LLED- HOT, AND CONDENSER WATER PI PI NG SYSTEMS

23 82 02. 00 10 UNI TARY HEATI NG AND COOLI NG EQUI PMENT

DI VI SI ON 25 - I NTEGRATED AUTOMATI ON

25 05 11 CYBERSECURI TY FOR FACI LI TY- RELATED CONTROL SYSTEMS

25 08 10 UTI LI TY MONI TORI NG AND CONTROL SYSTEM TESTI NG

DI VI SI ON 26 - ELECTRI CAL

26 05 19. 10 10 I NSULATED WI RE AND CABLE

26 05 48. 00 10 SEI SMI C PROTECTI ON FOR ELECTRI CAL EQUI PMENT

26 20 00 I NTERI OR DI STRI BUTI ON SYSTEM

26 28 01. 00 10 COORDI NATED POWER SYSTEM PROTECTI ON

26 29 23 VARI ABLE FREQUENCY DRI VE SYSTEMS UNDER 600 VOLTS

26 32 14. 00 10 DI ESEL- GENERATOR SET, STATI ONARY 15- 300 KW, STANDBY

APPLICATIONS

26 36 00. 00 10 AUTOMATI C TRANSFER SWI TCH AND BY- PASS/ I SOLATI ON SWI TCH

26 41 00 LI GHTNI NG PROTECTI ON SYSTEM

26 51 00 I NTERI OR LI GHTI NG

DI VI SI ON 27 - COMMUNI CATI ONS

27 05 14. 00 10 CABLE TELEVI SI ON PREMI SES DI STRI BUTI ON SYSTEM

27 10 00 BUI LDI NG TELECOMMUNI CATI ONS CABLI NG SYSTEM

27 51 23. 10 I NTERCOMMUNI CATI ON SYSTEM

DI VI SI ON 28 - ELECTRONI C SAFETY AND SECURI TY

28 10 05 ELECTRONI C SECURI TY SYSTEMS ( ESS)

28 31 76 I NTERI OR FI RE ALARM AND MASS NOTI FI CATI ON SYSTEM

DI VI SI ON 31 - EARTHWORK

31 00 00 EARTHWORK

31 63 29 DRI LLED CONCRETE PI ERS AND SHAFTS

DI VI SI ON 32 - EXTERI OR I MPROVEMENTS

32 01 19 FI ELD MOLDED SEALANTS FOR SEALI NG JOI NTS I N RI GI D

PAVEMENTS

32 11 16 BASE COURSE FOR RI GI D PAVI NG

32 11 23 AGGREGATE AND/ OR GRADED- CRUSHED AGGREGATE BASE COURSE

32 13 13. 06 PORTLAND CEMENT CONCRETE PAVEMENT FOR ROADS AND SI TE

PROJECT TABLE OF CONTENTS Page 3

FACILITIES

32 16 13 CONCRETE SI DEWALKS AND CURBS AND GUTTERS

32 17 24. 00 10 PAVEMENT MARKI NGS

32 31 13. 53 HI GH- SECURI TY CHAI N LI NK FENCES AND GATES

32 92 19 SEEDING

32 92 23 SODDING

DI VI SI ON 33 - UTI LI TI ES

33 08 55 COMMI SSI ONI NG OF FUEL FACI LI TY SYSTEMS

33 11 00 WATER DI STRI BUTI ON

33 30 00 SANI TARY SEWERS

33 52 10 SERVI CE PI PI NG, FUEL SYSTEMS

33 56 10 FACTORY- FABRI CATED FUEL STORAGE TANKS

33 71 02 UNDERGROUND ELECTRI CAL DI STRI BUTI ON

33 82 00 TELECOMMUNI CATI ONS OUTSI DE PLANT ( OSP)

- - End of Pr oj ect Tabl e of Cont ent s - -

PROJECT TABLE OF CONTENTS Page 4

SECTI ON TABLE OF CONTENTS

DI VI SI ON 06 - WOOD, PLASTI CS, AND COMPOSI TES

SECTI ON 06 10 00

ROUGH CARPENTRY

08/16

PART 1 GENERAL

1. 1 REFERENCES

1. 2 SUBMI TTALS

1. 3 DELI VERY AND STORAGE

1. 4 GRADI NG AND MARKI NG

1. 4. 1 Lumber

1. 4. 2 Pl ywood

1. 4. 3 Pr eser vat i ve- Tr eat ed Lumber and Pl ywood

1. 5 SI ZES AND SURFACI NG

1. 6 MOI STURE CONTENT

1. 7 PRESERVATI VE TREATMENT

1. 8 CERTI FI CATI ONS

1. 8. 1 Cer t i f i ed Wood Gr ades

PART 2 PRODUCTS

2. 1 LUMBER

2. 1. 1 Fr ami ng Lumber

2. 2 OTHER MATERI ALS

2. 2. 1 Mi scel l aneous Wood Member s

2. 2. 1. 1 Nonst r ess Gr aded Member s

2. 2. 1. 2 Si l l Pl at es

2. 2. 1. 3 Bl ocki ng

2. 2. 2 Adhesi ves

2. 3 ROUGH HARDWARE

2. 3. 1 Bol t s, Nut s, St uds, and Ri vet s

2. 3. 2 Anchor Bol t s

2. 3. 3 Expansi on Shi el ds

2. 3. 4 Lag Scr ews and Lag Bol t s

2. 3. 5 Wood Scr ews

2. 3. 6 Nai l s

2. 3. 7 Wi r e Nai l s

2. 3. 8 Cl i p Angl es

2. 3. 9 Met al Fr ami ng Anchor s

2. 3. 10 Panel Edge Cl i ps

PART 3 EXECUTI ON

3. 1 I NSTALLATI ON

3. 1. 1 Si l l s

3. 1. 1. 1 Anchor s i n Masonr y

3. 1. 1. 2 Anchor s i n Concr et e

3. 2 MI SCELLANEOUS

3. 2. 1 Wood Roof Nai l er s, Edge St r i ps, Cr i cket s, Cur bs, and Cant s

3. 2. 1. 1 Roof Edge St r i ps and Nai l er s

SECTI ON 06 10 00 Page 1

3. 2. 1. 2 Cr i cket s, Cant s, and Cur bs

3. 2. 2 Wood Bl ocki ng

3. 2. 3 Wood Gr ounds

3. 2. 4 Wood Fur r i ng

3. 2. 5 Tempor ar y Cl osur es

3. 2. 6 Tempor ar y Cent er i ng, Br aci ng, and Shor i ng

3. 2. 7 Si l l Pl at es

- - End of Sect i on Tabl e of Cont ent s - -

SECTI ON 06 10 00 Page 2

SECTI ON 06 10 00

ROUGH CARPENTRY

08/16

PART 1 GENERAL

1. 1 REFERENCES

The publ i cat i ons l i s t ed bel ow f or m a par t of t hi s speci f i cat i on t o t he ext ent r ef er enced. The publ i cat i ons ar e r ef er r ed t o wi t hi n t he t ext by t he basi c desi gnat i on onl y.

AMERI CAN LUMBER STANDARDS COMMI TTEE ( ALSC)

ALSC PS 20 ( 2015) Amer i can Sof t wood Lumber St andar d

AMERI CAN WOOD COUNCI L ( AWC)

AWC NDS ( 2015) Nat i onal Desi gn Speci f i cat i on ( NDS) f or Wood Const r uct i on

AWC WFCM ( 2012) Wood Fr ame Const r uct i on Manual f or One- and Two- Fami l y Dwel l i ngs

AMERI CAN WOOD PROTECTI ON ASSOCI ATI ON ( AWPA)

AWPA M2 ( 2016) St andar d f or t he I nspect i on of Pr eser vat i ve Tr eat ed Wood Pr oduct s f or I ndust r i al Use

AWPA M6 ( 2013) Br ands Used on Pr eser vat i ve Tr eat ed Materials

APA - THE ENGI NEERED WOOD ASSOCI ATI ON ( APA)

APA L870 ( 2010) Vol unt ar y Pr oduct St andar d, PS 1- 09, St r uct ur al Pl ywood

ASME I NTERNATI ONAL ( ASME)

ASME B18. 2. 1 ( 2012; Er r at a 2013) Squar e and Hex Bol t s and Scr ews ( I nch Ser i es)

ASME B18. 2. 2 ( 2015) Nut s f or Gener al Appl i cat i ons:

Machi ne Scr ew Nut s, Hex, Squar e, Hex Fl ange, and Coupl i ng Nut s ( I nch Ser i es)

ASME B18. 5. 2. 1M ( 2006; R 2011) Met r i c Round Head Shor t Squar e Neck Bol t s

ASME B18. 5. 2. 2M ( 1982; R 2010) Met r i c Round Head Squar e Neck Bol t s

ASME B18. 6. 1 ( 2016) Wood Scr ews ( I nch Ser i es)

SECTI ON 06 10 00 Page 3

ASTM I NTERNATI ONAL ( ASTM)

ASTM A153/ A153M ( 2016) St andar d Speci f i cat i on f or Zi nc Coat i ng ( Hot - Di p) on I r on and St eel Hardware

ASTM A307 ( 2014; E 2017) St andar d Speci f i cat i on f or Car bon St eel Bol t s, St uds, and Thr eaded Rod 60 000 PSI Tensi l e St r engt h

ASTM A653/ A653M ( 2017) St andar d Speci f i cat i on f or St eel Sheet , Zi nc- Coat ed ( Gal vani zed) or Zi nc- I r on Al l oy- Coat ed ( Gal vanneal ed) by t he Hot - Di p Pr ocess

ASTM F1667 ( 2017) St andar d Speci f i cat i on f or Dr i ven Fast ener s: Nai l s, Spi kes, and St apl es

ASTM F547 ( 2017) St andar d Ter mi nol ogy of Nai l s f or Use wi t h Wood and Wood- Base Mat er i al s

FM GLOBAL ( FM)

FM 4435 ( 2013) Roof Per i met er Fl ashi ng

I NTERNATI ONAL CODE COUNCI L ( I CC)

I CC I BC ( 2018) I nt er nat i onal Bui l di ng Code

NATI ONAL HARDWOOD LUMBER ASSOCI ATI ON ( NHLA)

NHLA Rul es ( 2015) Rul es f or t he Measur ement & I nspect i on of Har dwood & Cypr ess

NORTHEASTERN LUMBER MANUFACTURERS ASSOCI ATI ON ( NELMA)

NELMA Gr adi ng Rul es ( 2013) St andar d Gr adi ng Rul es f or Nor t heast er n Lumber

REDWOOD I NSPECTI ON SERVI CE ( RI S) OF THE CALI FORNI A REDWOOD

ASSOCI ATI ON ( CRA)

RI S Gr ade Use ( 1998) Redwood Lumber Gr ades and Uses

SOUTHERN CYPRESS MANUFACTURERS ASSOCI ATI ON ( SCMA)

SCMA Spec ( 1986; Suppl e. No. 1, Aug 1993) St andar d Speci f i cat i ons f or Gr ades of Sout her n Cypress

SOUTHERN PI NE I NSPECTI ON BUREAU ( SPI B)

SPI B 1003 ( 2014) St andar d Gr adi ng Rul es f or Sout her n Pi ne Lumber

U. S. GENERAL SERVI CES ADMI NI STRATI ON ( GSA)

CI D A- A- 1923 ( Rev A; Not i ce 3) Shi el d, Expansi on ( Lag, Machi ne and Ext er nal l y Thr eaded Wedge Bol t

SECTI ON 06 10 00 Page 4

Anchors)

CI D A- A- 1924 ( Rev A; Not i ce 2) Shi el d, Expansi on ( Sel f Dr i l l i ng Tubul ar Expansi on Shel l Bol t Anchors

CI D A- A- 1925 ( Rev A; Not i ce 3) Shi el d Expansi on ( Nai l Anchors)

WEST COAST LUMBER I NSPECTI ON BUREAU ( WCLI B)

WCLI B 17 ( 2015) St andar d Gr adi ng Rul es

WESTERN WOOD PRODUCTS ASSOCI ATI ON ( WWPA)

WWPA G- 5 ( 2017) West er n Lumber Gr adi ng Rul es

1. 2 SUBMITTALS

Gover nment appr oval i s r equi r ed f or submi t t al s wi t h a " G" desi gnat i on;

submi t t al s not havi ng a " G" desi gnat i on ar e f or i nf or mat i on onl y. When used, a desi gnat i on f ol l owi ng t he " G" desi gnat i on i dent i f i es t he of f i ce t hat wi l l r evi ew t he submi t t al f or t he Gover nment . Submi t t al s wi t h an " S" ar e f or i ncl usi on i n t he Sust ai nabi l i t y eNot ebook, i n conf or mance wi t h Section 01 33 29 SUSTAI NABI LI TY REPORTI NG. Submi t t he f ol l owi ng i n accor dance wi t h Sect i on 01 33 00 SUBMI TTAL PROCEDURES:

SD- 02 Shop Dr awi ngs

Nai l er s and Nai l i ng St r i ps; G, RO

Dr awi ngs of f i el d er ect i on det ai l s , i ncl udi ng mat er i al s and met hods of f ast eni ng nai l er s i n conf or mance wi t h Fact or y Mut ual wi nd upl i f t r at ed syst ems speci f i ed i n ot her Sect i ons of t hese specifications.

SD- 03 Pr oduct Dat a

Adhesives

SD- 06 Test Repor t s

Preservative-treated Lumber and Pl ywood

SD- 07 Cer t i f i cat es

Cer t i f i cat es of Gr ade

Pr eser vat i ve Tr eat ment

I ndoor Ai r Qual i t y f or Aer osol Adhesi ves; S

SECTI ON 06 10 00 Page 5

I ndoor Ai r Qual i t y f or Non- aer osol Adhesi ves; S

1. 3 DELI VERY AND STORAGE

Del i ver mat er i al s t o t he s i t e i n an undamaged condi t i on. St or e, pr ot ect , handl e, and i nst al l pr ef abr i cat ed st r uct ur al el ement s i n accor dance wi t h manuf act ur er ' s i nst r uct i ons and as speci f i ed. St or e mat er i al s of f t he gr ound t o pr ovi de pr oper vent i l at i on, wi t h dr ai nage t o avoi d st andi ng wat er , and pr ot ect i on agai nst gr ound moi st ur e and dampness. St or e mat er i al s wi t h a moi st ur e bar r i er at bot h t he gr ound l evel and as a cover f or mi ng a wel l vent i l at ed encl osur e. St or e wood I - beams and gl ue- l ami nat ed beams and j oi st s on edge. Adher e t o r equi r ement s f or st acki ng, l i f t i ng, br aci ng, cut t i ng, not chi ng, and speci al f ast eni ng r equi r ement s. Do not use mat er i al s t hat have vi s i bl e moi st ur e or bi ol ogi cal gr owt h. Remove def ect i ve and damaged mat er i al s and pr ovi de new mat er i al s. St or e separ at ed r eusabl e wood wast e conveni ent t o cut t i ng st at i on and ar ea of wor k.

1. 4 GRADI NG AND MARKI NG

1. 4. 1 Lumber

Mar k each pi ece of f r ami ng and boar d l umber or each bundl e of smal l pi eces of l umber wi t h t he gr ade mar k of a r ecogni zed associ at i on or i ndependent i nspect i on agency. Such associ at i on or agency must be cer t i f i ed by t he Boar d of Revi ew, Amer i can Lumber St andar ds Commi t t ee, t o gr ade t he speci es used. Sur f aces t hat ar e t o be exposed t o v i ew must not bear gr ademar ks, st amps, or any t ype of i dent i f y i ng mar k. Hammer mar ki ng wi l l be per mi t t ed on t i mber s when al l sur f aces wi l l be exposed t o v i ew.

1. 4. 2 Plywood

Mar k each sheet wi t h t he mar k of a r ecogni zed associ at i on or i ndependent i nspect i on agency t hat mai nt ai ns cont i nui ng cont r ol over t he qual i t y of t he pl ywood. The mar k must i dent i f y t he pl ywood by speci es gr oup or span r at i ng, exposur e dur abi l i t y c l assi f i cat i on, gr ade, and compl i ance wi t h APA L870. Sur f aces t hat ar e t o be exposed t o v i ew must not bear gr ademar ks or ot her t ypes of i dent i f y i ng mar ks.

1. 4. 3 Preservative-Treated Lumber and Pl ywood

The Cont r act or i s r esponsi bl e f or t he qual i t y of t r eat ed wood pr oduct s.

Each t r eat ed pi ece must be i nspect ed i n accor dance wi t h AWPA M2 and per manent l y mar ked or br anded, by t he pr oducer , i n accor dance wi t h AWPA M6.

The Cont r act or must pr ovi de Cont r act i ng Of f i cer ' s Repr esent at i ve ( COR) wi t h t he i nspect i on r epor t of an appr oved i ndependent i nspect i on agency t hat of f er ed pr oduct s compl y wi t h appl i cabl e AWPA St andar ds. The appr opr i at e Qual i t y Mar k on each pi ece wi l l be accept ed, i n l i eu of i nspect i on r epor t s, as evi dence of compl i ance wi t h appl i cabl e AWPA t r eat ment st andar ds.

1. 5 SI ZES AND SURFACI NG

ALSC PS 20 f or dr essed si zes of yar d and st r uct ur al l umber . Lumber must be sur f aced f our s i des. Si ze r ef er ences, unl ess ot her wi se speci f i ed, ar e nomi nal s i zes, and act ual s i zes must be wi t hi n manuf act ur i ng t ol er ances al l owed by t he st andar d under whi ch t he pr oduct i s pr oduced. Ot her measur ement s ar e I P or SI st andar d.

SECTI ON 06 10 00 Page 6

1. 6 MOI STURE CONTENT

Ai r - dr y or k i l n- dr y l umber . Ki l n- dr y t r eat ed l umber af t er t r eat ment .

Maxi mum moi st ur e cont ent of wood pr oduct s must be as f ol l ows at t he t i me of del i ver y t o t he j ob s i t e:

a. Fr ami ng l umber and boar d, 19 per cent maxi mum

b. Ti mber s 5 i nches and t hi cker , 25 per cent maxi mum

d. Mat er i al s ot her t han l umber ; moi st ur e cont ent must be i n accor dance wi t h st andar d under whi ch t he pr oduct i s pr oduced

1. 7 PRESERVATI VE TREATMENT

a. 0. 25 pcf i nt ended f or above gr ound use.

b. 0. 40 pcf i nt ended f or gr ound cont act and f r esh wat er use. 0. 60 pcf i nt ended f or Ammoni acal Copper Quat er nar y Compound ( ACQ) - t r eat ed foundations. 0. 80 t o 1. 00 pcf i nt ended f or ACQ- t r eat ed pi l i ngs. Al l wood must be ai r or k i l n dr i ed af t er t r eat ment . Speci f i c t r eat ment s must be ver i f i ed by t he r epor t of an appr oved i ndependent i nspect i on agency, or t he AWPA Qual i t y Mar k on each pi ece. Br ush coat ar eas t hat ar e cut or dr i l l ed af t er t r eat ment wi t h ei t her t he same pr eser vat i ve used i n t he t r eat ment or wi t h a 2 per cent copper napht henat e sol ut i on. Pl ast i c l umber must not be pr eser vat i ve t r eat ed. The f ol l owi ng i t ems must be pr eser vat i ve t r eat ed:

( 1) Wood f r ami ng, woodwor k, and pl ywood up t o and i ncl udi ng t he subf l oor i ng at t he f i r st - f l oor l evel of st r uct ur es havi ng cr awl spaces when t he bot t oms of such i t ems ar e 24 i nches or l ess f r om t he ear t h under neat h.

( 2) Wood member s t hat ar e i n cont act wi t h wat er .

( 3) Ext er i or wood st eps, pl at f or ms, and r ai l i ngs; and al l wood f r ami ng of open, r oof ed st r uct ur es.

( 4) Wood si l l s , sol es, pl at es, f ur r i ng, and sl eeper s t hat ar e l ess t han 24 i nches f r om t he gr ound, f ur r i ng and nai l er s t hat ar e set i nt o or i n cont act wi t h concr et e or masonr y.

( 5) Nai l er s, edge st r i ps, cr i cket s, cur bs, and cant s f or r oof decks.

1. 8 CERTIFICATIONS

1. 8. 1 Cer t i f i ed Wood Gr ades

Provide cer t i f i cat es of gr ade f r om t he gr adi ng agency on gr aded but unmar ked l umber or pl ywood at t est i ng t hat mat er i al s meet t he gr ade r equi r ement s speci f i ed her ei n.

PART 2 PRODUCTS

2. 1 LUMBER

2. 1. 1 Fr ami ng Lumber

Fr ami ng l umber such as st uds, pl at es, caps, col l ar beams, cant st r i ps, SECTI ON 06 10 00 Page 7 bucks, s l eeper s, nai l i ng st r i ps, and nai l er s and boar d l umber such as subf l oor i ng and wal l and r oof sheat hi ng must be one of t he speci es l i s t ed i n t he t abl e bel ow. Mi ni mum gr ade of speci es must be as l i s t ed.

Tabl e of Gr ades f or Fr ami ng and Boar d Lumber

Gr adi ng Rul es Species Framing Boar d Lumber

WWPA G- 5 st andar d gr adi ng r ul es

Aspen, Dougl as Fi r - Lar ch, Dougl as Fi r Sout h, Engelmann Spruce-Lodgepole Pi ne, Engel mann Spr uce, Hem- Fi r , I daho Whi t e Pi ne, Lodgepol e Pi ne, Mount ai n Heml ock, Mountain Hemlock-Hem-Fir, Ponderosa Pi ne- Sugar Pi ne, Ponderosa Pine-Lodgepole Pi ne, Subal pi ne Fi r , Whi t e Woods, West er n Woods, West er n Cedar s, West er n Heml ock

Al l Speci es:

St andar d Li ght Fr ami ng or No. 3 St r uct ur al Li ght Fr ami ng ( St ud Gr ade f or 2x4 nomi nal s i ze, 10 feet and shor t er )

Al l Speci es:

No. 3 Common

WCLI B 17 st andar d gr adi ng r ul es

Dougl as Fi r - Lar ch, Hem- Fi r , Mount ai n Heml ock, Si t ka Spr uce, West er n Cedar s, West er n Hemlock

Al l Speci es:

St andar d Li ght Fr ami ng or No. 3 St r uct ur al Li ght Fr ami ng ( St ud Gr ade f or 2x4 nomi nal s i ze, 10 feet and shor t er )

Al l Speci es:

Standard

SECTI ON 06 10 00 Page 8

Tabl e of Gr ades f or Fr ami ng and Boar d Lumber

Gr adi ng Rul es Species Framing Boar d Lumber

SPI B 1003 st andar d gr adi ng r ul es

Sout her n Pi ne Al l Speci es:

St andar d Li ght Fr ami ng or No. 3 St r uct ur al Li ght Fr ami ng ( St ud Gr ade f or 2x4 nomi nal s i ze, 10 feet and shor t er )

No. 2 Boar ds

SCMA Spec st andar d specifications

Cypress No. 2 Common No. 2 Common

NELMA Gr adi ng Rul es st andar d gr adi ng r ul es

Bal sam Fi r , East er n Hemlock-Tamarack, East er n Spr uce, East er n Whi t e Pi ne, Nor t her n Pi ne, Nor t her n Pi ne- Cedar

Al l Speci es:

St andar d Li ght Fr ami ng or No. 3 St r uct ur al Li ght Fr ami ng ( St ud Gr ade f or 2x4 nomi nal s i ze, 10 feet and shor t er )

Al l Speci es:

No. 3 Common except St andar d f or East er n Whi t e and Nor t her n Pi ne

RI S Gr ade Use standard specifications

Redwood Al l Speci es:

St andar d Li ght Fr ami ng or No. 3 St r uct ur al Li ght Fr ami ng ( St ud Gr ade f or 2x4 nomi nal s i ze, 10 feet and shor t er )

Const r uct i on Hear t

SECTI ON 06 10 00 Page 9

Tabl e of Gr ades f or Fr ami ng and Boar d Lumber

Gr adi ng Rul es Species Framing Boar d Lumber

NHLA Rul es r ul es f or t he measur ement and i nspect i on of har dwood and cypr ess lumber

Cypress No. 2 Di mensi on No. 2 Common

2. 2 OTHER MATERI ALS

2. 2. 1 Mi scel l aneous Wood Member s

2. 2. 1. 1 Nonst r ess Gr aded Member s

Member s must i nc l ude br i dgi ng, cor ner br aci ng, f ur r i ng, gr ounds, and nai l i ng st r i ps. Member s must be i n accor dance wi t h TABLE I f or t he speci es used. Si zes must be as f ol l ows unl ess ot her wi se shown:

Member Size i nch

Bridging 1 x 3 or 1 x 4 f or use bet ween member s 2 x 12 and smal l er ; 2 x 4 f or use bet ween member s l ar ger t han 2 x 12.

Cor ner br aci ng 1 x 4.

Furring 1 x 2

Grounds Pl ast er t hi ckness by 38.

Nai l i ng st r i ps 1 x 3 or 1 x 4 when used as shi ngl e base or i nt er i or f i ni sh, otherwise 2 i nch st ock.

2. 2. 1. 2 Si l l Pl at es

Si l l pl at es must be st andar d or number 2 gr ade.

2. 2. 1. 3 Blocking

Bl ocki ng must be st andar d or number 2 gr ade.

2. 2. 2 Adhesives

Compl y wi t h appl i cabl e r egul at i ons r egar di ng t oxi c and hazar dous mat er i al s

SECTI ON 06 10 00 Page 10 and as speci f i ed. Pr ovi de cer t i f i cat i on of i ndoor ai r qual i t y f or non- aer osol adhesi ves appl i ed on t he i nt er i or of t he bui l di ng ( i nsi de of t he weat her pr oof i ng syst em) . Pr ovi de cer t i f i cat i on of i ndoor ai r qual i t y f or aer osol adhesi ves used on t he i nt er i or of t he bui l di ng ( i nsi de of t he weat her pr oof i ng syst em) .

2. 3 ROUGH HARDWARE

Unl ess ot her wi se i ndi cat ed or speci f i ed, r ough har dwar e must be of t he t ype and si ze necessar y f or t he pr oj ect r equi r ement s. Si zes, t ypes, and spaci ng of f ast eni ngs of manuf act ur ed bui l di ng mat er i al s UST be as r ecommended by t he pr oduct manuf act ur er unl ess ot her wi se i ndi cat ed or speci f i ed. Rough har dwar e exposed t o t he weat her or embedded i n or i n cont act wi t h pr eser vat i ve t r eat ed wood, ext er i or masonr y, or concr et e wal l s or s l abs must be hot - di p z i nc- coat ed i n accor dance wi t h ASTM A153/ A153M. Nai l s and f ast eni ngs f or f i r e- r et ar dant t r eat ed l umber and woodwor k exposed t o t he weat her must be copper al l oy or hot - di pped gal vani zed f ast ener s as r ecommended by t he t r eat ed wood manuf act ur er .

2. 3. 1 Bol t s, Nut s, St uds, and Ri vet s

ASME B18. 2. 1, ASME B18. 5. 2. 1M, ASME B18. 5. 2. 2M and ASME B18. 2. 2.

2. 3. 2 Anchor Bol t s

ASTM A307, s i ze as i ndi cat ed, compl et e wi t h nut s and washer s.

2. 3. 3 Expansi on Shi el ds

CI D A- A- 1923, CI D A- A- 1924, and CI D A- A- 1925. Except as shown ot her wi se, maxi mum si ze of devi ces must be 3/ 8 i nch.

2. 3. 4 Lag Scr ews and Lag Bol t s

ASME B18. 2. 1.

2. 3. 5 Wood Scr ews

ASME B18. 6. 1.

2. 3. 6 Nails

ASTM F547, s i ze and t ype best sui t ed f or pur pose. For sheat hi ng and subf l oor i ng, l engt h of nai l s must be suf f i c i ent t o ext end 1 i nch i nt o suppor t s. I n gener al , 8- penny or l ar ger nai l s must be used f or nai l i ng through 1 i nch t hi ck l umber and f or t oe nai l i ng 2 i nch t hi ck l umber ;

16- penny or l ar ger nai l s must be used f or nai l i ng t hr ough 2 i nch t hi ck l umber . Nai l s used wi t h t r eat ed l umber and sheat hi ng must be hot - di pped gal vani zed i n accor dance wi t h ASTM A153/ A153M. Nai l i ng must be i n accor dance wi t h t he r ecommended nai l i ng schedul e cont ai ned i n AWC WFCM.

Wher e det ai l ed nai l i ng r equi r ement s ar e not speci f i ed, nai l s i ze and spaci ng must be suf f i c i ent t o devel op an adequat e st r engt h f or t he connect i on. The connect i on' s st r engt h must be ver i f i ed agai nst t he nai l capaci t y t abl es i n AWC NDS. Reasonabl e j udgment backed by exper i ence must ensur e t hat t he desi gned connect i on wi l l not cause t he wood t o spl i t . I f a l oad s i t uat i on exceeds a r easonabl e l i mi t f or nai l s, a speci al i zed connect or must be used.

SECTI ON 06 10 00 Page 11

2. 3. 7 Wi r e Nai l s

ASTM F1667.

2. 3. 8 Cl i p Angl es

Steel, 3/ 16 i nch t hi ck, s i ze as i ndi cat ed; or z i nc- coat ed st eel or i r on commer ci al c l i ps desi gned f or connect i ng wood member s.

2. 3. 9 Met al Fr ami ng Anchor s

Const r uct anchor s t o t he conf i gur at i on shown usi ng hot di p z i nc- coat ed st eel conf or mi ng t o ASTM A653/ A653M, G90. Except wher e ot her wi se shown, St eel must be not l i ght er t han 18 gage. Speci al nai l s suppl i ed by t he manuf act ur er must be used f or al l nai l i ng.

2. 3. 10 Panel Edge Cl i ps

Ext r uded al umi num or gal vani zed st eel , H- shaped cl i ps t o pr event di f f er ent i al def l ect i on of r oof sheat hi ng.

PART 3 EXECUTI ON

3. 1 INSTALLATION

Do not i nst al l bui l di ng const r uct i on mat er i al s t hat show vi sual evi dence of bi ol ogi cal gr owt h.

Conf or m t o AWC WFCM unl ess ot her wi se i ndi cat ed or speci f i ed. Sel ect l umber s i zes t o mi ni mi ze wast e. Fi t f r ami ng l umber and ot her r ough car pent r y, set accur at el y t o t he r equi r ed l i nes and l evel s, and secur e i n pl ace i n a r i gi d manner . Do not spl i ce f r ami ng member s bet ween bear i ng poi nt s. Set j oi st s, r af t er s, and pur l i ns wi t h t hei r cr own edge up. Fr ame member s f or t he passage of pi pes, condui t s, and duct s. Do not cut or bor e st r uct ur al member s f or t he passage of duct s or pi pes wi t hout appr oval . Rei nf or ce al l member s damaged by such cut t i ng or bor i ng by means of speci al l y f or med and appr oved sheet met al or bar st eel shapes, or r emove and pr ovi de new, as appr oved. Pr ovi de as necessar y f or t he pr oper compl et i on of t he wor k al l f r ami ng member s not i ndi cat ed or speci f i ed. Spi k i ng and nai l i ng not i ndi cat ed or speci f i ed ot her wi se must be i n accor dance wi t h t he Nai l i ng Schedul e cont ai ned i n I CC I BC; per f or m bol t i ng i n an appr oved manner .

Spi kes, nai l s, and bol t s must be dr awn up t i ght . Use sl at e or st eel shi ms when l evel i ng j oi st s, beams, and gi r der s on masonr y or concr et e. Do not use shi mmi ng on wood or met al bear i ngs. When j oi st s, beams, and gi r der s ar e pl aced on masonr y or concr et e, a wood base pl at e must be posi t i oned and l evel ed wi t h gr out . The j oi st , beam, or gi r der must t hen be pl aced on t he pl at e. When j oi st s, beams, and gi r der s ar e set i nt o masonr y or concr et e, a pocket must be f or med i nt o t he wal l . The j oi st , beam, or gi r der must t hen be pl aced i nt o t he pocket and l evel ed wi t h a st eel shi m.

3. 1. 1 Sills

Set s i l l s l evel and squar e and wedge wi t h st eel or s l at e shi ms; poi nt or gr out wi t h non- shr i nki ng cement mor t ar t o pr ovi de cont i nuous and sol i d bear i ng. Anchor s i l l s t o t he f oundat i ons as i ndi cat ed. Wher e s i zes and spaci ng of anchor bol t s ar e not i ndi cat ed, pr ovi de not l ess t han 5/ 8 i nch di amet er bol t s at al l cor ner s and spl i ces and space at a maxi mum of 6 f eet

o. c. bet ween cor ner bol t s. Pr ovi de at l east t wo bol t s f or each si l l member . Lap and spl i ce s i l l s at cor ner s and bol t t hr ough t he l aps or but t

SECTI ON 06 10 00 Page 12 t he ends and t hr ough- bol t not mor e t han 6 i nches f r om t he ends. Pr ovi de bol t s wi t h pl at e washer s and nut s. Bol t s i n ext er i or wal l s must be zinc-coated.

3. 1. 1. 1 Anchor s i n Masonr y

Except wher e i ndi cat ed ot her wi se, embed anchor bol t s not l ess t han 15 i nches i n masonr y uni t wal l s and pr ovi de each wi t h a nut and a 2 i nch di amet er washer at bot t om end. Ful l y gr out bol t s wi t h mor t ar .

3. 1. 1. 2 Anchor s i n Concr et e

Except wher e i ndi cat ed ot her wi se, embed anchor bol t s not l ess t han 8 i nches i n pour ed concr et e wal l s and pr ovi de each wi t h a nut and a 2 i nch di amet er washer at bot t om end. A bent end may be subst i t ut ed f or t he nut and washer ; bend must be not l ess t han 90 degr ees. Powder - act uat ed f ast ener s spaced 3 f eet o. c. may be pr ovi ded i n l i eu of bol t s f or s i ngl e t hi ckness pl at es on concr et e.

3. 2 MISCELLANEOUS

3. 2. 1 Wood Roof Nai l er s, Edge St r i ps, Cr i cket s, Cur bs, and Cant s

Pr ovi de s i zes and conf i gur at i ons i ndi cat ed or speci f i ed and anchor ed secur el y t o cont i nuous const r uct i on.

3. 2. 1. 1 Roof Edge St r i ps and Nai l er s

Pr ovi de at per i met er of r oof , ar ound openi ngs t hr ough r oof , and wher e r oof s abut wal l s, cur bs, and ot her ver t i cal sur f aces. Except wher e i ndi cat ed ot her wi se, nai l er s must be 6 i nches wi de and t he same t hi ckness as t he i nsul at i on. Anchor nai l er s secur el y t o under l y i ng const r uct i on. Anchor per i met er nai l er s i n accor dance wi t h FM 4435.

3. 2. 1. 2 Cr i cket s, Cant s, and Cur bs

Pr ovi de wood saddl es or cr i cket s, cant st r i ps, cur bs f or scut t l es and vent i l at or s, and wood nai l er s bol t ed t o t ops of concr et e or masonr y cur bs and at expansi on j oi nt s, as i ndi cat ed, speci f i ed, or necessar y and of lumber.

3. 2. 2 Wood Bl ocki ng

Pr ovi de pr oper s i zes and shapes at pr oper l ocat i ons f or t he i nst al l at i on and at t achment of wood and ot her f i ni sh mat er i al s, f i x t ur es, equi pment , and i t ems i ndi cat ed or speci f i ed.

3. 2. 3 Wood Gr ounds

Pr ovi de f or f ast eni ng wood t r i m, f i ni sh mat er i al s, and ot her i t ems t o pl ast er ed wal l s and cei l i ngs. I nst al l gr ounds i n pr oper al i gnment and t r ue wi t h an 8 f oot st r ai ght edge.

3. 2. 4 Wood Fur r i ng

Pr ovi de wher e shown and as necessar y f or f aci ng mat er i al s speci f i ed. Except as shown ot her wi se, f ur r i ng st r i ps must be nomi nal one by 3, cont i nuous, and spaced 16 i nches o. c. Er ect f ur r i ng ver t i cal l y or hor i zont al l y as necessar y. Nai l f ur r i ng st r i ps t o masonr y. Do not use wood pl ugs.

SECTI ON 06 10 00 Page 13

Pr ovi de f ur r i ng st r i ps ar ound openi ngs, behi nd bases, and at angl es and cor ner s. Fur r i ng must be pl umb, r i gi d, and l evel and must be shi mmed as necessar y t o pr ovi de a t r ue, even pl ane wi t h sur f aces sui t abl e t o r ecei ve t he f i ni sh r equi r ed. For m f ur r i ng f or of f set s and br eaks i n wal l s or cei l i ngs on 1 by 4 wood st r i ps spaced 16 i nches o. c.

3. 2. 5 Tempor ar y Cl osur es

Pr ovi de wi t h hi nged door s and padl ocks and i nst al l dur i ng const r uct i on at ext er i or door ways and ot her gr ound l evel openi ngs t hat ar e not ot her wi se c l osed. Cover wi ndows and ot her unpr ot ect ed openi ngs wi t h pol yet hyl ene or ot her appr oved mat er i al , s t r et ched on wood f r ames. Pr ovi de dust pr oof bar r i er par t i t i ons t o i sol at e ar eas as di r ect ed.

3. 2. 6 Tempor ar y Cent er i ng, Br aci ng, and Shor i ng

For ms and cent er i ng f or cast - i n- pl ace concr et e wor k ar e speci f i ed i n Section 03 30 00 CAST- I N- PLACE CONCRETE.

3. 2. 7 Si l l Pl at es

Si l l pl at es must be set l evel and squar e and anchor bol t ed at not mor e t han 6 f eet on cent er s and not mor e t han 12 i nches f r om end of each pi ece. A mi ni mum of t wo anchor s must be used f or each pi ece.

- - End of Sect i on - -

SECTI ON 06 10 00 Page 14

SECTI ON TABLE OF CONTENTS

DI VI SI ON 06 - WOOD, PLASTI CS, AND COMPOSI TES

SECTI ON 06 20 00

FI NI SH CARPENTRY

08/16

PART 1 GENERAL

1. 1 REFERENCES

1. 2 SUBMI TTALS

1. 3 DETAI L DRAWI NGS

1. 4 PRODUCT DATA

1. 5 SAMPLES

1. 6 DELI VERY, STORAGE, AND HANDLI NG

1. 7 QUALI TY ASSURANCE

1. 7. 1 Lumber

1. 7. 2 Pl ywood

1. 7. 3 Pr essur e Tr eat ed Lumber and Pl ywood

1. 7. 4 Non- Pr essur e Tr eat ed Woodwor k and Mi l l wor k

1. 7. 5 Fi r e- Ret ar dant Tr eat ed Lumber

PART 2 PRODUCTS

2. 1 PRODUCT SUSTAI NABI LI TY CRI TERI A

2. 1. 1 Cer t i f i ed Sust ai nabl y Har vest ed Wood

2. 1. 2 Recycl ed Cont ent f or Wood Pr oduct s

2. 1. 3 Reduce Vol at i l e Or gani c Compounds ( VOC) ( Low- Emi t t i ng

Mat er i al s) f or Pr oduct s

2. 2 WOOD PRODUCTS

2. 2. 1 Si zes and Pat t er ns of Wood Pr oduct s

2. 2. 2 Tr i m, Fi ni sh, and Fr ames

2. 2. 3 Sof t wood Pl ywood

2. 2. 4 Har dwood Pl ywood

2. 3 MOI STURE CONTENT OF WOOD PRODUCTS

2. 4 PRESERVATI VE TREATMENT OF WOOD PRODUCTS

2. 4. 1 Pr essur e Tr eat ment

2. 5 FI RE- RETARDANT TREATMENT

2. 5. 1 Wood Pr oduct s

2. 6 HARDWARE AND ACCESSORI ES

2. 6. 1 Wood Scr ews

2. 6. 2 Bol t s, Nut s, Lag Scr ews, and St uds

2. 6. 3 Nai l s

2. 7 FABRI CATI ON

2. 7. 1 Qual i t y St andar ds ( QS)

2. 7. 2 Cabi net s

2. 7. 2. 1 Cabi net Har dwar e

2. 7. 2. 2 Fi ni sh

2. 7. 3 Casewor k wi t h Hi gh Pr essur e Lami nat e Fi ni sh

2. 7. 3. 1 AWI Qual i t y Gr ade

2. 7. 3. 2 Const r uct i on

2. 7. 3. 3 Exposed Sur f aces

2. 7. 3. 4 Semi - Exposed Sur f aces

SECTI ON 06 20 00 Page 1

2. 7. 3. 5 Edge Bandi ng

PART 3 EXECUTI ON

3. 1 FI NI SH WORK

3. 2 SHELVI NG

SECTI ON 06 20 00 Page 2

SECTI ON 06 20 00

FI NI SH CARPENTRY

08/16

PART 1 GENERAL

1. 1 REFERENCES

The publ i cat i ons l i s t ed bel ow f or m a par t of t hi s speci f i cat i on t o t he ext ent r ef er enced. The publ i cat i ons ar e r ef er r ed t o wi t hi n t he t ext by t he basi c desi gnat i on onl y.

AMERI CAN LUMBER STANDARDS COMMI TTEE ( ALSC)

ALSC PS 20 ( 2015) Amer i can Sof t wood Lumber St andar d

AMERI CAN WOOD PROTECTI ON ASSOCI ATI ON ( AWPA)

AWPA M4 ( 2015) St andar d f or t he Car e of Pr eser vat i ve- Tr eat ed Wood Pr oduct s

AWPA U1 ( 2017) Use Cat egor y Syst em: User Speci f i cat i on f or Tr eat ed Wood

APA - THE ENGI NEERED WOOD ASSOCI ATI ON ( APA)

APA L870 ( 2010) Vol unt ar y Pr oduct St andar d, PS 1- 09, St r uct ur al Pl ywood

ARCHI TECTURAL WOODWORK I NSTI TUTE ( AWI )

AWI AWS ( 2nd Edi t i on) Ar chi t ect ur al Woodwor k Standards

ASME I NTERNATI ONAL ( ASME)

ASME B18. 2. 1 ( 2012; Er r at a 2013) Squar e and Hex Bol t s and Scr ews ( I nch Ser i es)

ASME B18. 2. 2 ( 2015) Nut s f or Gener al Appl i cat i ons:

Machi ne Scr ew Nut s, Hex, Squar e, Hex Fl ange, and Coupl i ng Nut s ( I nch Ser i es)

ASME B18. 6. 1 ( 2016) Wood Scr ews ( I nch Ser i es)

ASTM I NTERNATI ONAL ( ASTM)

ASTM D2898 ( 2010; R 2017) St andar d Pr act i ce f or Accel er at ed Weat her i ng of Fi r e- Ret ar dant - Tr eat ed Wood f or Fi r e Testing

ASTM F547 ( 2017) St andar d Ter mi nol ogy of Nai l s f or Use wi t h Wood and Wood- Base Mat er i al s

SECTI ON 06 20 00 Page 3

BUI LDERS HARDWARE MANUFACTURERS ASSOCI ATI ON ( BHMA)

ANSI / BHMA A156. 9 ( 2015) Cabi net Har dwar e

HARDWOOD PLYWOOD AND VENEER ASSOCI ATI ON ( HPVA)

HPVA HP- 1 ( 2016) Amer i can Nat i onal St andar d f or Har dwood and Decor at i ve Pl ywood

NATI ONAL HARDWOOD LUMBER ASSOCI ATI ON ( NHLA)

NHLA Rul es ( 2015) Rul es f or t he Measur ement & I nspect i on of Har dwood & Cypr ess

NORTHEASTERN LUMBER MANUFACTURERS ASSOCI ATI ON ( NELMA)

NELMA Gr adi ng Rul es ( 2013) St andar d Gr adi ng Rul es f or Nor t heast er n Lumber

REDWOOD I NSPECTI ON SERVI CE ( RI S) OF THE CALI FORNI A REDWOOD

ASSOCI ATI ON ( CRA)

RI S Gr ade Use ( 1998) Redwood Lumber Gr ades and Uses

SOUTHERN PI NE I NSPECTI ON BUREAU ( SPI B)

SPI B 1003 ( 2014) St andar d Gr adi ng Rul es f or Sout her n Pi ne Lumber

WEST COAST LUMBER I NSPECTI ON BUREAU ( WCLI B)

WCLI B 17 ( 2015) St andar d Gr adi ng Rul es

WESTERN WOOD PRODUCTS ASSOCI ATI ON ( WWPA)

WWPA G- 5 ( 2017) West er n Lumber Gr adi ng Rul es

WI NDOW AND DOOR MANUFACTURERS ASSOCI ATI ON ( WDMA)

WDMA I . S. 4 ( 2015A) Pr eser vat i ve Tr eat ment f or Mi l l wor k

WOOD MOULDI NG AND MI LLWORK PRODUCERS ASSOCI ATI ON ( WMMPA)

WMMPA WM 6 ( 2007) Qual i t y I ndust r y St andar ds Bookl et

1. 2 SUBMITTALS

Gover nment appr oval i s r equi r ed f or submi t t al s wi t h a " G" desi gnat i on;

submi t t al s not havi ng a " G" desi gnat i on ar e f or i nf or mat i on onl y. When used, a desi gnat i on f ol l owi ng t he " G" desi gnat i on i dent i f i es t he of f i ce t hat wi l l r evi ew t he submi t t al f or t he Gover nment . Submi t t he f ol l owi ng i n accor dance wi t h Sect i on 01 33 00 SUBMI TTAL PROCEDURES:

SD- 02 Shop Dr awi ngs

Det ai l Dr awi ngs I ndi cat i ng Al l Wood Assembl i es

SD- 03 Pr oduct Dat a

SECTI ON 06 20 00 Page 4

Tr eat ed Wood Pr oduct s

Har dwar e and Accessor i es

SD- 04 Sampl es

Samples

1. 3 DETAI L DRAWI NGS

Submit det ai l dr awi ngs i ndi cat i ng al l wood assembl i es pr oposed f or use i n t he pr oj ect . I ndi cat e mat er i al s, speci es, gr ade, densi t y, gr ai n, f i ni sh det ai l s of const r uct i on, l ocat i on of use i n t he pr oj ect , f i ni shes, t ypes, met hod and ar r angement of f ast ener s, and i nst al l at i on det ai l s . Thi s i ncl udes al l f abr i cat ed assembl i es.

1. 4 PRODUCT DATA

Submi t Manuf act ur er s pr i nt ed dat a i ncl udi ng pr oposed speci es, gr ade, densi t y gr ai n, and f i ni sh as appl i cabl e; suf f i c i ent t o demonst r at e compl i ance wi t h t hi s speci f i cat i on f or each t ype of wood pr oduct speci f i ed. For t r eat ed wood pr oduct s al so pr ovi de document at i on of envi r onment al l y saf e pr eser vat i ves f or each t ype of wood pr oduct speci f i ed.

Pr ovi de Manuf act ur er s pr i nt ed dat a f or har dwar e and al l wood accessor i es i ncl udi ng but not l i mi t ed t o edge bandi ng, adhesi ves, and seal er s.

1. 5 SAMPLES

Sampl es i ndi cat i ng pr oposed speci es, gr ade, densi t y gr ai n, and f i ni sh f or each t ype of wood pr oduct speci f i ed. Pr ovi de sampl es of suf f i c i ent s i ze t o show pat t er n and col or r anges of pr oposed pr oduct s.

1. 6 DELI VERY, STORAGE, AND HANDLI NG

Del i ver wood pr oduct s t o t he j obsi t e i n an undamaged condi t i on. St ack mat er i al s t o ensur e vent i l at i on and dr ai nage. Pr ot ect agai nst dampness bef or e and af t er del i ver y. St or e mat er i al s under cover i n a wel l vent i l at ed encl osur e and pr ot ect agai nst ext r eme changes i n t emper at ur e and humi di t y. Keep mat er i al s wr apped and separ at ed f r om of f - gassi ng mat er i al s ( such as dr y i ng pai nt s and adhesi ves) . Do not use mat er i al s t hat have vi s i bl e moi st ur e or bi ol ogi cal gr owt h. Do not st or e pr oduct s i n bui l di ng unt i l wet t r ade mat er i al s ar e dr y and humi di t y of t he space i s wi t hi n wood manuf act ur er ' s t ol er ance l i mi t s f or st or age.

1. 7 QUALI TY ASSURANCE

1. 7. 1 Lumber

I dent i f y each pi ece or each bundl e of l umber , mi l l wor k, and t r i m by t he gr ade mar k of a r ecogni zed associ at i on or i ndependent i nspect i on agency cer t i f i ed by t he Boar d of Revi ew of t he ALSC t o gr ade t he speci es.

1. 7. 2 Plywood

Pr ovi de each sheet of pl ywood wi t h t he mar k of a r ecogni zed associ at i on or i ndependent i nspect i on agency t hat mai nt ai ns cont i nui ng cont r ol over t he qual i t y of t he pl ywood. Mar ks must i dent i f y pl ywood by speci es gr oup or span r at i ng, exposur e dur abi l i t y c l assi f i cat i on, gr ade, and compl i ance wi t h

SECTI ON 06 20 00 Page 5

APA L870.

1. 7. 3 Pr essur e Tr eat ed Lumber and Pl ywood

I nspect each t r eat ed pi ece i n accor dance wi t h AWPA U1.

1. 7. 4 Non- Pr essur e Tr eat ed Woodwor k and Mi l l wor k

Mar k, st amp, or l abel t o i ndi cat e compl i ance wi t h WDMA I . S. 4.

1. 7. 5 Fi r e- Ret ar dant Tr eat ed Lumber

Each pi ece must bear an Under wr i t er s Labor at or i es f i r e r esi st ance l abel or compar abl e l abel of anot her nat i onal l y r ecogni zed i ndependent f i r e r et ar dant mat er i al s t est i ng l abor at or y.

PART 2 PRODUCTS

2. 1 PRODUCT SUSTAI NABI LI TY CRI TERI A

For pr oduct s i n t hi s sect i on, wher e appl i cabl e and t o ext ent al l owed by per f or mance cr i t er i a, pr ovi de and document t he f ol l owi ng:

2. 1. 1 Cer t i f i ed Sust ai nabl y Har vest ed Wood

Cer t i f i ed sust ai nabl y har vest ed wood i s i dent i f i ed f or some pr oduct s i n t hi s sect i on; pr ovi de document at i on i n accor dance wi t h Sect i on 01 33 29 SUSTAI NABI LI TY REPORTI NG par agr aph BI OBASED PRODUCTS. Ot her pr oduct s l i s t ed i n t hi s sect i on may be avai l abl e as cer t i f i ed sust ai nabl y har vest ed wood;

i dent i f y t hose pr oduct s t hat meet pr oj ect r equi r ement s f or cer t i f i ed sust ai nabl y har vest ed wood, and pr ovi de document at i on i n accor dance wi t h Section 01 33 29 SUSTAI NABI LI TY REPORTI NG par agr aph BI OBASED PRODUCTS.

2. 1. 2 Recycl ed Cont ent f or Wood Pr oduct s

Recycl ed cont ent i s i dent i f i ed f or some pr oduct s i n t hi s sect i on; pr ovi de document at i on i n accor dance wi t h Sect i on 01 33 29 SUSTAI NABI LI TY REPORTI NG par agr aph RECYCLED CONTENT. Ot her pr oduct s l i s t ed i n t hi s sect i on may be avai l abl e wi t h r ecycl ed cont ent ; i dent i f y t hose pr oduct s t hat meet pr oj ect r equi r ement s f or r ecycl ed cont ent , and pr ovi de document at i on i n accor dance wi t h Sect i on 01 33 29 SUSTAI NABI LI TY REPORTI NG par agr aph RECYCLED CONTENT.

2. 1. 3 Reduce Vol at i l e Or gani c Compounds ( VOC) ( Low- Emi t t i ng Mat er i al s) f or Products

Reduced VOC cont ent i s i dent i f i ed f or some pr oduct s i n t hi s sect i on;

pr ovi de document at i on i n accor dance wi t h Sect i on 01 33 29 SUSTAI NABI LI TY REPORTI NG par agr aph REDUCE VOLATI LE ORGANI C COMPOUNDS ( VOC) ( LOW- EMI TTI NG MATERI ALS) . Ot her pr oduct s l i s t ed i n t hi s sect i on may be avai l abl e wi t h r educed VOC cont ent ; i dent i f y t hose pr oduct s t hat meet pr oj ect r equi r ement s f or r educed VOC cont ent , and pr ovi de document at i on i n accor dance wi t h Section 01 33 29 SUSTAI NABI LI TY REPORTI NG par agr aph REDUCE VOLATI LE ORGANI C

COMPOUNDS ( VOC) ( LOW- EMI TTI NG MATERI ALS) .

2. 2 WOOD PRODUCTS

2. 2. 1 Si zes and Pat t er ns of Wood Pr oduct s

Pr ovi de yar d and boar d l umber s i zes i n accor dance wi t h ALSC PS 20. Pr ovi de

SECTI ON 06 20 00 Page 6 shaped l umber and mi l l wor k i n t he pat t er ns i ndi cat ed and i n st andar d pat t er ns of t he associ at i on cover i ng t he speci es. Si ze r ef er ences, unl ess ot her wi se speci f i ed, ar e nomi nal s i zes. Pr ovi de act ual s i zes wi t hi n manuf act ur i ng t ol er ances al l owed by t he appl i cabl e st andar d.

2. 2. 2 Tr i m, Fi ni sh, and Fr ames

Pr ovi de speci es and gr ades l i s t ed i n t he t abl e bel ow f or wood mat er i al s t hat must be pai nt ed. For mat er i al s t hat must be st ai ned, have a nat ur al , or a t r anspar ent f i ni sh, pr ovi de mat er i al s one gr ade hi gher t han t hose l i s t ed i n t he t abl e bel ow. Pr ovi de t r i m, except wi ndow st ool s and apr ons wi t h hol l ow backs.

TABLE OF GRADES FOR WOOD TO RECEI VE PAI NT FI NI SH

Gr adi ng Rul es Species Ext er i or and I nt er i or Tr i m, Fi ni sh, and Fr ames

WWPA G- 5 st andar d gr adi ng r ul es

Aspen, Dougl as Fi r - Lar ch, Dougl as Fi r Sout h, Engel mann Spr uce- Lodgepol e Pi ne, Engel mann Spr uce, Hem- Fi r , I daho Whi t e Pi ne, Lodgepol e Pi ne, Mount ai n Heml ock, Mount ai n Heml ock- Hem- Fi r , Ponder osa Pi ne- Sugar Pi ne, ( Ponder osa Pi ne- Lodgepol e Pi ne, ) Whi t e Woods, ( West er n Woods, ) West er n Cedar s, West er n Heml ock

Al l Speci es: C & BTR. Sel ect ( Choi ce & BTR I daho Whi t e Pi ne) or Super i or Fi ni sh.

West er n Red Cedar may be gr aded C & BTR. Sel ect or A & BTR i n accor dance wi t h Speci al West er n Red Cedar Rules.

WCLI B 17 st andar d gr adi ng r ul es

Dougl as Fi r - Lar ch, Hem- Fi r , Mount ai n Heml ock, Si t ka Spr uce, West er n Cedar s, West er n Heml ock

Al l Speci es: C & BTR VG, except A f or West er n Red Cedar

SPI B 1003 st andar d gr adi ng r ul es

Sout her n Pi ne C & BTR

NHLA Rul es Cypress C-Select

NELMA Gr adi ng Rul es st andar d gr adi ng r ul es * *

Bal sam Fi r , East er n Heml ock- Tamar ack, East er n Spr uce, East er n Whi t e Pi ne, Nor t her n Pi ne, Nor t her n Pi ne, Nor t her n Whi t e Cedar

Al l Speci es: C- Sel ect except C & BTR f or East er n Whi t e Pi ne and Nor way Pi ne

SECTI ON 06 20 00 Page 7

TABLE OF GRADES FOR WOOD TO RECEI VE PAI NT FI NI SH

Gr adi ng Rul es Species Ext er i or and I nt er i or Tr i m, Fi ni sh, and Fr ames

RI S Gr ade Use standard specifications

Redwood Cl ear , Cl ear Al l Hear t

NHLA Rul es Cypress B Fi ni sh

Red Gum, Sof t El m, Bi r ch Sel ect or BTR ( f or i nt er i or use onl y)

Not e: * * http://www.nelma.org/library/2013-standard-grading-rules-for-northeastern-lumber/

2. 2. 3 Sof t wood Pl ywood

Pr ovi de i n accor dance wi t h APA L870.

a. Pl ywood f or Shel v i ng: I nt er i or t ype, A- B Gr ade, any speci es gr oup.

2. 2. 4 Har dwood Pl ywood

HPVA HP- 1, Type I I ( I nt er i or ) , Pr emi um ( A) l umber cor e const r uct i on, f ace veneer s of r ed oak, of t hi ckness i ndi cat ed.

2. 3 MOI STURE CONTENT OF WOOD PRODUCTS

Ai r dr y or k i l n dr y l umber . Ki l n dr y t r eat ed l umber af t er t r eat ment .

Maxi mum moi st ur e cont ent of wood pr oduct s at t i me of del i ver y t o t he j obsi t e, and when i nst al l ed, must be as f ol l ows:

a. I nt er i or Fi ni sh Lumber , Tr i m, and Mi l l wor k: 1- 1/ 4 I nches Nomi nal or Less i n Thi ckness: 6 per cent on 85 per cent of t he pi eces and 8 per cent on r emai nder .

b. Pr ovi de moi st ur e cont ent of ot her mat er i al s i n accor dance wi t h t he appl i cabl e st andar ds.

2. 4 PRESERVATI VE TREATMENT OF WOOD PRODUCTS

2. 4. 1 Pr essur e Tr eat ment

Lumber and pl ywood used on t he ext er i or of bui l di ngs or i n cont act wi t h masonr y or concr et e shal l be pr essur e- t r eat ed wi t h wat er bor ne pr eser vat i ve

SECTI ON 06 20 00 Page 8 l i st ed i n AWPA U1 ( P ser i es i s i ncl uded t her ei n by r ef er ence) as appl i cabl e, and i nspect ed i n accor dance wi t h AWPA U1. I dent i f y t r eat ment on each pi ece of mat er i al by t he qual i t y mar k of an agency accr edi t ed by t he Boar d of Revi ew of t he Amer i can Lumber St andar ds Commi t t ee. Pr ovi de t r eat ed pl ywood t o a r ef l ect i on l evel as f ol l ows:

Pr eser vat i ve t r eat ext er i or wood moul di ng and mi l l wor k t hat wi l l be wi t hi n 18 i nches of soi l or i n cont act wi t h wat er or concr et e i n accor dance wi t h WMMPA WM 6. Pr ovi de a f i el d t r eat ment i n accor dance wi t h AWPA M4 of exposed ar eas of t r eat ed wood t hat have been cut or dr i l l ed. I t ems of al l - hear t mat er i al of cedar , cypr ess, or r edwood do not r equi r e pr eser vat i ve t r eat ment except when i n di r ect cont act wi t h soi l .

2. 5 FI RE- RETARDANT TREATMENT

2. 5. 1 Wood Pr oduct s

Pr essur e t r eat f i r e- r et ar dant t r eat ed l umber and pl ywood i n accor dance wi t h AWPA U1. Compl y wi t h mat er i al use as def i ned i n AWPA U1 f or I nt er i or Type A and Ext er i or Type. Tr eat ment and per f or mance i nspect i on must be conduct ed by a qual i f i ed i ndependent t est i ng agency t hat est abl i shes per f or mance r at i ngs. Each pi ece or bundl e of t r eat ed mat er i al must bear i dent i f i cat i on of t he t est i ng agency t o i ndi cat e per f or mance wi t h such r at i ng. Subj ect t r eat ed mat er i al s t hat wi l l be exposed t o r ai n wet t i ng t o an accel er at ed weat her i ng t echni que i n accor dance wi t h ASTM D2898, Met hod A, pr i or t o bei ng t est ed f or compl i ance wi t h AWPA U1.

2. 6 HARDWARE AND ACCESSORI ES

Pr ovi de s i zes, t ypes, and spaci ngs of har dwar e and accessor i es as r ecommended i n wr i t i ng by t he wood pr oduct manuf act ur er , except as ot her wi se speci f i ed.

2. 6. 1 Wood Scr ews

ASME B18. 6. 1.

2. 6. 2 Bol t s, Nut s, Lag Scr ews, and St uds

ASME B18. 2. 1 and ASME B18. 2. 2.

2. 6. 3 Nails

Use nai l s of a s i ze and t ype best sui t ed f or each appl i cat i on and i n accor dance wi t h ASTM F547. Use hot - di pped gal vani zed or al umi num nai l s f or ext er i or appl i cat i ons. For s i di ng, pr ovi de nai l s of suf f i c i ent l engt h t o extend 1- 1/ 2 i nches i nt o suppor t s, i ncl udi ng wood sheat hi ng over f r ami ng.

Wher e nai l i ng i s i mpr act i cal , pr ovi de scr ews of a s i ze and t ype best sui t ed f or each appl i cat i on.

2. 7 FABRICATION

2. 7. 1 Qual i t y St andar ds ( QS)

The t er ms " Pr emi um, " " Cust om, " and " Economy" r ef er t o t he qual i t y gr ades def i ned i n AWI AWS. Pr ovi de i t ems not ot her wi se speci f i ed i n a speci f i c gr ade as " Cust om" gr ade.

SECTI ON 06 20 00 Page 9

2. 7. 2 Cabinets

Unl ess speci f i ed ot her wi se, pr ovi de wal l and base cabi net s of t he same const r uct i on, mat er i al s, and f i ni shes as count er t ops. Count er t ops shal l be i n accor dance wi t h Sect i on 06 61 16 SOLI D SURFACI NG FABRI CATI ONS. Fabr i cat e cabi net s wi t h sol i d ends and f r ame f r ont s, or wi t h f r ames al l ar ound.

Pr ovi de f r ames of sol i d har dwood not l ess t han 3/ 4 by 1- 1/ 2 i nches.

Pr ovi de ends, bot t oms, backs, par t i…