A10_Amendment_03_to_Solicitation_W912DR-16-T-0043.pdf

AMENDMENT OF SOLICITATION/MODIFICATION OF CONTRACT

Except as provided herein, all terms and conditions of the document referenced in Item 9A or 10A, as heretofore changed, remains unchanged and in full force and effect.

15A. NAME AND TITLE OF SIGNER (Type or print)

30-105-04EXCEPTION TO SF 30

APPROVED BY OIRM 11-84

STANDARD FORM 30 (Rev. 10-83) Prescribed by GSA

FAR (48 CFR) 53.243

The purpose of this amendment is to add a revised statement of w ork dated 16 August 2016. All other terms and conditions remain unchanged.

Contracting POC: Tamara Udasco, tamara.c.udasco@usace.army.mil

1. CONTRACT ID CODE PAGE OF PAGES

1 6

16A. NAME AND TITLE OF CONTRACTING OFFICER (Type or print)

16C. DATE SIGNED

BY 16-Aug-2016

16B. UNITED STATES OF AMERICA15C. DATE SIGNED15B. CONTRACTOR/OFFEROR

(Signature of Contracting Officer)(Signature of person authorized to sign)

8. NAME AND ADDRESS OF CONTRACTOR (No., Street, County, State and Zip Code) X W912DR-16-T-0043

X 9B. DATED (SEE ITEM 11)

11-Jul-2016

10B. DATED (SEE ITEM 13)

9A. AMENDMENT OF SOLICITATION NO.

11. THIS ITEM ONLY APPLIES TO AMENDMENTS OF SOLICITATIONS

X The above numbered solicitation is amended as set forth in Item 14. The hour and date specified for receipt of Offer is extended, X is not extended.

Offer must acknowledge receipt of this amendment prior to the hour and date specified in the solicitation or as amended by one of the following methods:

(a) By completing Items 8 and 15, and returning copies of the amendment; (b) By acknowledging receipt of this amendment on each copy of the offer submitted;

or (c) By separate letter or telegram which includes a reference to the solicitation and amendment numbers. FAILURE OF YOUR ACKNOWLEDGMENT TO BE RECEIVED AT THE PLACE DESIGNATED FOR THE RECEIPT OF OFFERS PRIOR TO THE HOUR AND DATE SPECIFIED MAY RESULT IN

REJECTION OF YOUR OFFER. If by virtue of this amendment you desire to change an offer already submitted, such change may be made by telegram or letter, provided each telegram or letter makes reference to the solicitation and this amendment, and is received prior to the opening hour and date specified.

12. ACCOUNTING AND APPROPRIATION DATA (If required)

13. THIS ITEM APPLIES ONLY TO MODIFICATIONS OF CONTRACTS/ORDERS.

IT MODIFIES THE CONTRACT/ORDER NO. AS DESCRIBED IN ITEM 14.

A. THIS CHANGE ORDER IS ISSUED PURSUANT TO: (Specify authority) THE CHANGES SET FORTH IN ITEM 14 ARE MADE IN THE

CONTRACT ORDER NO. IN ITEM 10A.

B. THE ABOVE NUMBERED CONTRACT/ORDER IS MODIFIED TO REFLECT THE ADMINISTRATIVE CHANGES (such as changes in paying office, appropriation date, etc.) SET FORTH IN ITEM 14, PURSUANT TO THE AUTHORITY OF FAR 43.103(B).

C. THIS SUPPLEMENTAL AGREEMENT IS ENTERED INTO PURSUANT TO AUTHORITY OF:

D. OTHER (Specify type of modification and authority)

E. IMPORTANT: Contractor is not, is required to sign this document and return copies to the issuing office.

14. DESCRIPTION OF AMENDMENT/MODIFICATION (Organized by UCF section headings, including solicitation/contract subject matter where feasible.)

10A. MOD. OF CONTRACT/ORDER NO.

2. AMENDMENT/MODIFICATION NO. 5. PROJECT NO.(If applicable)

6. ISSUED BY

3. EFFECTIVE DATE

16-Aug-2016

CODE

U.S. ARMY CORPS OF ENGINEERS, BALTIMORE

10 S. HOWARD STREET

ROOM 7000

BALTIMORE MD 21201

W912DR 7. ADMINISTERED BY (If other than item 6)

4. REQUISITION/PURCHASE REQ. NO.

CODE

See Item 6

FACILITY CODECODE

EMAIL:TEL:

W912DR-16-T-0043

SECTION SF 30 BLOCK 14 CONTINUATION PAGE

SUMMARY OF CHANGES

SECTION SF 30 - BLOCK 14 CONTINUATION PAGE

The following have been modified:

STATEMENT OF WORK

STATEMENT OF WORK

Track Mount Tilt Bed Drill Rig

U.S. Army Corps of Engineers – Baltimore District

16 August 2016

1.0 Introduction

This requirement is for supplies for the U.S. Army Corps of Engineers (USACE), Baltimore District’s Field Exploration Unit (FEU). This a firm fixed-price purchase order for the purchase of commercial supplies to include:

Fabrication, 1-Year Warranty, and Training for a new Track Mount Tilt Bed Drill Rig

The U.S. Army Corps of Engineers, Baltimore District Field Exploration Unit (FEU) performs critical in-house drilling services, requires information on procuring a drill rig. The FEU is requesting a new Track-Mount Tilt-Bed Drill Rig be built to replace an aging track mount tilt bed drill rig. The track mount tilt bed rig will be utilized to perform drilling on steep embankments often associated with dam and levee evaluations. The ability to access locations along steep embankments is critical to performing in-house services within the North Atlantic Division as well as Corps-wide. The two features which make this rig ideal for steep embankment access are the track mounted and tilt bed capabilities. The track mounted capabilities allow the rig to easily maneuver over tough, rocky terrain.

2.0 Requirements and Technical Specifications

The vendor shall adhere to the specifications provided by USACE herein for the fabrication of track mount tilt bed drill rig. The unit shall be completely assembled and fully equipped in accordance with the specifications and ready for operation when delivered. The drill unit shall be thoroughly field tested and ready for immediate and continuous operation at time of delivery.

The drill rig shall meet the following Technical Specifications:

1) Integrated Track and Carrier System (from same designer)

2) On Rig Storage for Augers (racks should not impede approach angle ability), Rods (rod box and rod slide), and Drilling Tools (such as hammer pocket for handling 6” and 8” bits)

3) Independent Track Control and Wireless Remote Control

4) 4 Derrick Winches including 1 Mainline with jib (Mainline with jib not required if using top head drive for tooling), Wireline/Sandline Winches (greater than 18,000 lbs (1), greater than 5,000 lbs (1), and greater than 2,500 lbs (1), 1 hydraulic jib boom with hydraulic swing and extension and 4,000 lbs.

5) Steel Skid Pan

6) < = 8 foot width (maximum 8’ 6” width only if required due to rig load)

7) > = 24,500 lbs. pull back

8) > = 18,000 lbs. pull down

9) > 45 degree Tilt-bed Angle Drilling Ability with all braces and legs included (stowable in-place during movement), for work area uphill of rig

10) > = 15” in/out table movement -

11) > = 6” side table/head movement

12) > = 14,500 ft lbs. rotary torque

13) > = 600 RPM for coring operation

14) 140/300 lb Auto Hammer

15) >= 24 inch track width, steel track shoe with bolted rubber pads

16) >= 40,000 lbs tractive force

17) < = 3 psi ground bearing pressure

18) < = 11’ inside turning radius

19) Rotary drilling transmission 4 speed fwd, 1 speed rev., or hydrostatic

20) Carrier transmission 2-speed hydrostatic with forward and reverse

21) Rig corner anchor eyes (for anchoring while on slopes without brakes engaged)

22) 7.5” x 10” Duplex Hydraulic Mud Pump with gardner denver type valves with bolt down valve caps, and shear type relief valve (Centerline Manufacturing Co. CLM 7½" x 10" Duplex Hydraulic Mud Pump or equivalent)

23) 3-Stage Progressive Cavity Pump with > =100 gpm, 225psi, 15HP motor (Moyno 3L8 or equivalent)

24) > = 27 foot Derrick

25) 4 Jack Tubes > = 30 inches in length (outrigger H-style “out and down type” w/ min. 24” extension and residual release valves on cylinder) with valves built into cylinder no hose between cylinder and valve.

26) Mud plumbing all steel (Schedule. 80) with pressure fittings (boss fittings, hammer lock unions and whip checks) on the pressure side of pump, no cam locks overhead.

27) Complete set of chucks and table slips with hydraulic chuck system

28) 36", 48" and 60" break out wrenches

29) Anchor Point in Derrick Crown for Fall Protection and Derrick Ladder if Tubular Mast

30) Front and rear hydraulic winches (30,000 lbs. each) (Ramsey RPH 30,000 or equivalent), capable of full power while simultaneously fully powering the tracks.

31) All required subs and gimbal for augering

32) > = 23 foot stroke

33) onboard > =1050/350 air compressor and down the hole hammer line oiler

34) Water injection pump > = 15 gpm at 600 psi (Bean E0413 or equivalent)

35) Mast strength >= 50,000 lbs.

36) Bank of four open hydraulic valves for future applications

37) 565 Horse Power Deck Engine (Caterpillar C15 or equivalent)

38) Low oil and high temperature shutdown sensors for compressor, engine, and hydraulic systems.

39) Fuel system capacity minimum of 12 hours at full load.

40) On-board removable vise for breaking split-spoon samplers.

41) All periodic maintenance items must be accessible and user serviceable.

42) Operation of all systems within an environmental temperature range of 10 to 120 degrees

Fahrenheit.

43) Six tool hangers on driller side, and six tool hangers on helper side.

44) Anchors on derrick to secure winch cables during transport.

Additional Requirements:

The drill rig is to be delivered in operating condition with acceptance subject to inspection and approval to the USACE Baltimore District’s Field Exploration Unit Warehouse located at Aberdeen Proving Ground – Edgewood Area, Edgewood, MD 21040.

The successful vendor shall provide manufacturer’s approved training to familiarize personnel with the correct operation and servicing procedures for the equipment delivered at a time and place agreed upon by the Government.

The successful vendor shall provide a minimum one year warranty on the drill rig.

All items which require periodic lubrication shall be provided with a suitable lubrication fitting.

Two hard copies and two CD-ROM electronic versions of the manufacturer's service manual containing operating instructions, maintenance instructions and a bill of material or parts list shall be furnished by the manufacturer.

All pressure systems shall be provided with suitable pressure relief valves. With the exception of the drilling tools, all moving parts that may present a potential hazard to personnel while operating or performing maintenance shall be fully enclosed or properly guarded to ensure the safety of personnel conducting operating and performing maintenance. Protective devices shall not impair the operating functions.

All water and mud pumps shall have easily accessible drain plugs. Exception allowed for water injection pump.

All pumps will be easily accessible for maintenance.

All valves on mud system will be designed for use on a mud rotary with controls at driller’s station. No ball valves or gate valves.

The equipment to be furnished under these specifications shall be warranted against defective design, materials and workmanship as standard with the manufacturer. Two hard copies and two CD-ROM electronic versions of the manufacturer's standard guaranty or warranty shall be furnished.

3.0 Period of Performance

This is a firm–fixed-price purchase order. The period of performance on this purchase order is eighteen (18) months from date of award.

(End of Summary of Changes)