Att_B_-_Paint_Spec_Sheet.pdf

SCHEDULE

Interior Finishes

Concrete/Cement Primer: B79W08810 - ProBlock® Interior Oil-Based Primer White Finish: B73W00111 - Waterbased Tile-Clad® Epoxy (Part A) Extra White/Tint Base

END OF SECTION

SURFACE PREPARATION

1) Previously Coated Surfaces Maintenance painting will frequently not permit or require complete removal of all old coatings prior to repainting. However, all surface contamination such as oil, grease, loose paint, mill scale, dirt, foreign matter, rust, mold, mildew, mortar, efflorescence, and sealers must be removed to assure sound bonding to the tightly adhering old paint. Glossy surfaces of old paint films must be clean and dull before repainting. Thorough washing with an abrasive cleanser will clean and dull in one operation, or, wash thoroughly and dull by sanding. Spot prime any bare areas with an appropriate primer.

Recognize that any surface preparation short of total removal of the old coating may compromise the service length of the system. Check for compatibility by applying a test patch of the recommended coating system, covering at least 2 to 3 square feet. Allow to dry one week before testing adhesion per ASTM D3359. If the coating system is incompatible, complete removal is required.

2) Hand Tool Cleaning Hand Tool Cleaning removes all loose mill scale, loose rust, and other detrimental foreign matter. It is not intended that adherent mill scale, rust, and paint be removed by this process. Mill scale, rust, and paint are considered adherent if they cannot be removed by lifting with a dull putty knife. Before hand tool cleaning, remove visible oil, grease, soluble residues, and salts by the methods outlined in SSPC- SP1. For complete instructions, refer to Steel Structures Paint Council Surface Preparation Specification No. 2 (SSPC-SP2)

3) Power Tool Cleaning Power Tool Cleaning removes all loose mill scale, loose rust, and other detrimental foreign matter. It is not intended that adherent mill scale, rust, and paint be removed by this process. Mill scale, rust, and paint are considered adherent if they cannot be removed by lifting with a dull putty knife. Before power tool cleaning, remove visible oil, grease, soluble residues, and salts by the methods outlined in SSPC- SP1. For complete instructions, refer to Steel Structures Paint Council Surface Preparation Specification No.3.(SSP-PC3)

END OF SPECIFICATION

Data Pages

109.34

PROBLOCK

Interior Oil-Based Primer

B79W8810

CHARACTERISTICS

Color: White Coverage: 350 - 400 sq ft/gal @ 4 mils wet; 2.1 mils dry Drying Time, @ 77°F, 50% RH:

Touch: 30 minutes Recoat: 60 - 90 minutes Drying and recoat times are temperature, humidity and film thickness dependent.

Finish: 5-15 units @ 85° Flash Point: 62°F, PMCC Vehicle Type: Linseed Vinyl Toluene

B79W08810 VOC (less exempt solvents):

349 g/L; 2.91 lb/gal Volume Solids: 54 ± 2% Weight Solids: 76 ± 2% Weight per Gallon: 12.3 lb WVP Perms (US) 1.4 grains/(hr ft2 in Hg)

Tinting Requires Blend-A-Color Toner for tinting.

For best color development, use the rec-ommended "P"-shade primer. If desired, up to 4 oz per gallon of Blend-A-Color Toner can be used to approximate the topcoat color. Check color before use.

When spot priming on some surfaces, a non-uniform appearance of the final coat may result, due to differences in holdout between primed and unprimed areas. To avoid this, prime the entire surface rather than spot priming.

For optimal performance, this primer must be topcoated with a latex or alkyd/ oil coating on architectural applications.

SURFACE PREPARATION

WARNING! Removal of old paint by sanding, scraping or other means may generate dust or fumes that contain lead.

Exposure to lead dust or fumes may cause brain damage or other adverse health effects, especially in children or pregnant women. Controlling exposure to lead or other hazardous substances re-quires the use of proper protective equip-ment, such as a properly fitted respirator (NIOSH approved) and proper contain-ment and cleanup. For more information, call the National Lead Information Center at 1-800-424-LEAD (in US) or contact your local health authority.

Remove all surface contamination by washing with an appropriate cleaner, rinse thoroughly and allow to dry. Scrape and sand peeled or checked paint to a sound surface. Sand glossy surfaces dull.

Smoke, fire, or stain damaged areas- Thoroughly clean the surface before ap-plying to smoke, fire or stained areas.

After priming, allow to dry 4 hours, test a small area for bleeding by applying the topcoat before painting the entire project.

If the stain bleeds through, apply a sec-ond coat of primer and allow to dry over-night and retest before topcoating. Use Multi-Purpose Latex Primer over solvent sensitive stains.

DESCRIPTION

• Seals out:

• water sensitive stains

• dried water stains

• smoke stains and related odors

• grease, ink, and pencil stains

• Quick drying

• Assures uniform appearance of top-coats

Use on these stained surfaces:

• Drywall

• Wood

• Cured Plaster

• Ceiling Tiles

• Paneling

• Nonporous Wallcovering

• Previously Painted surfaces

3/2013 www.sherwin-williams.com continued on back

As of 01/01/2013, Complies with:

OTC Yes LEED® 09 CI No SCAQMD No LEED® 09 NC No CARB No LEED® 09 CS No CARB SCM 2007 No LEED® H No MPI # 45, 46 NGBS No

The information and recommendations set forth in this Product Data Sheet are based upon tests con-ducted by or on behalf of The Sherwin-Williams Com-pany. Such information and recommendations set forth herein are subject to change and pertain to the product offered at the time of publication. Consult your Sherwin-Williams representative to obtain the most recent Product Data Sheet.

109.34

PROBLOCK

Interior Oil-Based Primer

B79W8810

APPLICATION

Do not reduce for stain blocking.

Apply at temperatures above 50°F.

No reduction needed.

Brush Use a natural bristle brush.

Roller Use a 1/4" - 1/2" nap synthetic or mohair roller cover.

Spray - Airless Pressure ................................ 2000 psi Tip ...................................... .015"-.017"

CLEANUP INFORMATION

Clean spills, spatters, and tools immedi-ately after use with mineral spirits. Follow manufacturer’s safety recommendations when using mineral spirits.

CAUTIONS

For interior use only.

LABEL CAUTIONS

ALIPHATIC HYDROCARBONS, CRYSTALLINE

SILICA. Contents are FLAMMABLE. Vapors may cause flash fires. Keep away from heat, sparks, and open flame. During use and until all vapors are gone:

Keep area ventilated - Do not smoke - Extinguish all flames, pilot lights, and heaters - Turn off stoves, electric tools and appliances, and any other sources of ignition. VAPOR HARMFUL. Use only with ade-quate ventilation. To avoid overexposure, open win-dows and doors or use other means to ensure fresh air entry during application and drying. If you experi-ence eye watering, headaches, or dizziness, increase fresh air, or wear respiratory protection (NIOSH ap-proved) or leave the area. Adequate ventilation re-quired when sanding or abrading the dried film. If adequate ventilation cannot be provided wear an approved particulate respirator (NIOSH approved).

Follow respirator manufacturer’s directions for respi-rator use. Avoid contact with eyes and skin. Wash hands after using. Keep container closed when not in use. Do not transfer contents to other containers for storage. FIRST AID: In case of eye contact, flush thoroughly with large amounts of water for 15 minutes and get medical attention. For skin contact, wash thoroughly with soap and water. In case of respiratory difficulty, provide fresh air and call physician. If swal-lowed, call Poison Control Center, hospital emer-gency room, or physician immediately. DELAYED

EFFECTS FROM LONG TERM OVEREXPOSURE.

Contains solvents which can cause permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents can be harmful or fatal. Abrading or sanding of the dry film may release crystalline silica which has been shown to cause lung damage and cancer under long term exposure. WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

DO NOT TAKE INTERNALLY. KEEP OUT OF THE

REACH OF CHILDREN. DANGER: Rags, steel wool, other waste soaked with this product, and sanding residue may spontaneously catch fire if improperly discarded. Immediately place rags, steel wool, other waste soaked with this product, and sanding residue in a sealed, water-filled, metal container. Dispose of in accordance with local fire regulations.

HOTW 04/01/2013 B79W08810 18 00

SURFACE PREPARATION

Drywall Fill cracks and nail holes with patching paste/spackle and sand smooth. Joint compounds must be cured and sanded smooth. Remove all sanding dust.

Plaster Bare plaster must be cured and hard.

Textured, soft, porous, or powdery plaster should be treated with a solution of 1 pint household vinegar to 1 gallon of water.

Repeat until the surface is hard, rinse with clear water and allow to dry.

Wood Sand any exposed wood to a fresh sur-face. Patch all holes and imperfections with a wood filler or putty and sand smooth.

Mildew Remove before painting by washing with a solution of 1 part liquid bleach and 3 parts water. Apply the solution and scrub the mildewed area. Allow the solution to remain on the surface for 10 minutes.

Rinse thoroughly with water and allow the surface to dry before painting. Wear pro-tective eyewear, waterproof gloves, and protective clothing. Quickly wash off any of the mixture that comes in contact with your skin. Do not add detergents or am-monia to the bleach/water solution.

Caulking Gaps between walls, ceilings, crown moldings, and other interior trim can be filled with the appropriate caulk after priming the surface.

Revised 4/12

WATERBASED TILE-CLAD®

EPOXY FINISH

PART A B73-100 SERIES

PART B B73V100 HARDENER

Protective

Marine Coatings

4.19 www.sherwin-williams.com/protective

PRODUCT DESCRIPTION

WATERBASED TILE-CLAD EPOXY FINISH is a two component, low VOC, high performance, water based, epoxy/cycloaliphatic amine fi nish coating. Developed for use in industrial environments.

Waterbased Tile-Clad is a high gloss, abrasion resistant, low yel-lowing epoxy fi nish with excellent weathering properties.

• Early moisture resistance • Resists yellowing

• Chemical resistant • Fast dry

• Impact and abrasion resistant • Nonfl ammable

• Low odor • Low VOC

• Outstanding application properties

PRODUCT CHARACTERISTICS

Finish: High Gloss

Color: Wide range of colors available

Volume Solids: 44% ± 2%, mixed

Weight Solids: 54% ± 2%, mixed

VOC (EPA Method 24): <200 g/L; 1.67 lb/gal, mixed

Mix Ratio: 4:1

Recommended Spreading Rate per coat:

Minimum Maximum

Wet mils (microns) 4.5 (112) 9.0 (225) Dry mils (microns) 2.0 (50) 4.0 (100) ~Coverage sq ft/gal (m2/L) 176 (4.3) 352 (8.6) Theoretical coverage sq ft/gal (m2/L) @ 1 mil / 25 microns dft 704 (17.2)

NOTE: Brush or roll application may require multiple coats to achieve maximum fi lm thickness and uniformity of appearance.

Drying Schedule @ 5.0 mils wet (125 microns):

@ 50°F/10°C @ 77°F/25°C @ 100°F/38°C

50% RH

To touch: 1.5 hours 45 minutes 25 minutes To handle: 5.5 hours 4.5 hours 2 hours To recoat:

minimum: 8 hours 6 hours 3 hours maximum: 30 days 30 days 30 days

To cure: 7 days 7 days 7 days If maximum recoat time is exceeded, abrade surface before recoating.

Drying time is temperature, humidity, and fi lm thickness dependent.

Pot Life: 4.5 hours 3.5 hours 1.5 hours Sweat-in-time: 30 minutes 30 minutes 10 minutes

Shelf Life: 36 months, unopened Store indoors at 40°F (4.5°C) to 100°F (38°C).

Flash Point: >200°F (93°C), SETA Flash, mixed

Reducer/Clean Up: Water continued on back

RECOMMENDED USES

For use over prepared steel and concrete surfaces in industrial exposures such as:

• Marine applications • Manufacturing plants

• Structural steel • Pulp and paper mills

• Storage tank exteriors • Pharmaceutical facilities

• Nuclear power facilities • Clean rooms

• Food processing facilities • Bridges

• Wastewater treatment facilities

• Suitable for use in USDA inspected facilities

• Conforms to AWWA D102 OCS #5

• Acceptable for general purpose use on fl oors.

• Acceptable for use in high performance architectural applications.

• Complies with performance criteria of SSPC Paint 34.

PERFORMANCE CHARACTERISTICS

Substrate*: Steel Surface Preparation*: SSPC-SP10 / NACE 2 System Tested*:

1 ct. Waterbased Tile-Clad Epoxy Primer @ 4.0 mils (100 microns) dft 1 ct. Waterbased Tile-Clad Epoxy @ 4.0 mils (100 microns) dft

*unless otherwise noted below

Test Name Test Method Results

Abrasion Resistance (topcoat only)

ASTM D4060,

CS17 wheel, 1000 cycles, 1 kg load

120 mg loss

Adhesion ASTM D4541 550 psi Corrosion Weathering

ASTM D5894, 20

cycles, 6720 hours Passes

Dry Heat Resistance ASTM D2485 250°F (121°C)

Flexibility

ASTM D522,

180° bend, 1/4" mandrel

Passes

Impace Resistance, Direct (topcoat only)

ASTM D2794 160 in. lb.

Impact Resistance, Indirect (topcoat only) ASTM D2794 100 in. lb.

Irradiation-Effects on Coatings used in Nuclear Power Plants

ANSI 5.12 / ASTM

D4082-89 Passes

Moisture Condensation Resistance

ASTM D4585,

100°F (38°C), 2000 hours

Passes

Pencil Hardness ASTM D3363 HB Salt Fog Resistance

ASTM B117, 2000

hours Passes

Surface Burning* ASTM E84/NFPA

Flame Spread Index 15; Smoke Development Index 5

Thermal Shock ASTM D2246, 20 cycles Passes

*Report No. IM54.1157-01-01

4.19

EPOXY FINISH

PART A B73-100 SERIES

PART B B73V100 HARDENER

Protective

Marine Coatings www.sherwin-williams.com/protective

SURFACE PREPARATION

Surface must be clean, dry, and in sound condition. Remove all oil, dust, grease, dirt, loose rust, and other foreign material to ensure adequate adhesion.

Refer to product Application Bulletin for detailed surface prepara-tion information.

Do not use hydrocarbon solvents for cleaning.

Minimum recommended surface preparation:

* Iron & Steel: SSPC-SP2 Galvanizing: SSPC-SP1 Concrete & Masonry: SSPC-SP13/NACE 6, or ICRI No. 310.2, CSP 1-3 Wood, interior: Clean, smooth, dust free

* Primer recommended

Surface Preparation Standards Condition of Surface

ISO 8501-1

BS7079:A1

Swedish Std.

SIS055900 SSPC NACE

White Metal Sa 3 Sa 3 SP 5 1 Near White Metal Sa 2.5 Sa 2.5 SP 10 2 Commercial Blast Sa 2 Sa 2 SP 6 3 Brush-Off Blast Sa 1 Sa 1 SP 7 4 Hand Tool Cleaning Rusted C St 2 C St 2 SP 2 -

Pitted & Rusted D St 2 D St 2 SP 2 - Power Tool Cleaning Rusted C St 3 C St 3 SP 3 -

Pitted & Rusted D St 3 D St 3 SP 3 -

TINTING

Tint Part A with EnviroToner Colorants at 100% strength. Five minutes minimum mixing on a mechanical shaker is required for complete mixing of color.

Do not use Blend-A-Color Toner.

APPLICATION CONDITIONS

Temperature: 50°F (10°C) minimum, 100°F (38°C) maximum (air, surface, and material) At least 5°F (2.8°C) above dew point Relative humidity: 85% maximum Refer to product Application Bulletin for detailed application infor-mation.

ORDERING INFORMATION

Packaging: 5 gallons (18.9L) mixed Part A: 4 gallons (15.1L) in a 5 gallon (18.9L) can and 1 gallon (3.78L) Part B: 1 gallon (3.78L) and 1 quart (0.94L)

Weight per gallon: 10.5 ± 0.2 lb ; 1.26 Kg/L, mixed

SAFETY PRECAUTIONS

Refer to the MSDS sheet before use.

Published technical data and instructions are subject to change without notice.

Contact your Sherwin-Williams representative for additional technical data and instructions.

WARRANTY

The Sherwin-Williams Company warrants our products to be free of manufactur-ing defects in accord with applicable Sherwin-Williams quality control procedures.

Liability for products proven defective, if any, is limited to replacement of the defec-tive product or the refund of the purchase price paid for the defective product as determined by Sherwin-Williams. NO OTHER WARRANTY OR GUARANTEE

OF ANY KIND IS MADE BY SHERWIN-WILLIAMS, EXPRESSED OR IMPLIED,

STATUTORY, BY OPERATION OF LAW OR OTHERWISE, INCLUDING MER-

CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

PRODUCT INFORMATION

RECOMMENDED SYSTEMS

Dry Film Thickness / ct.

Mils (Microns) Steel:

1 ct. Waterbased Tile-Clad Epoxy Primer 2.0-4.0 (50-100) 1-2 cts. Waterbased Tile-Clad Epoxy Finish 2.0-4.0 (50-100)

Steel:

1 ct. ProCryl Universal WB Primer 3.0-4.0 (75-100) 1-2 cts. Waterbased Tile-Clad Epoxy Finish 2.0-4.0 (50-100)

Steel:

1 ct. Recoatable Epoxy Primer 4.0-6.0 (100-150) 1-2 cts. Waterbased Tile-Clad Epoxy Finish 2.0-4.0 (50-100)

Steel:

1 ct. Zinc-Clad VI 2.0-3.0 (50-75) 1 ct. Waterbased Tile-Clad Epoxy Finish 2.0-4.0 (50-100) 1-2 cts. Water Based Acrolon 100 2.0-4.0 (50-100)

Concrete/Masonry:

1 ct. Cement-Plex 875 13.0-25.0 (325-625) (as required to fi ll voids and provide a continuous surface)

Other acceptable surfacers are:

Heavy Duty Block Filler Kem Cati-Coat HS Epoxy Filler/Sealer Topcoat 1-2 cts. Waterbased Tile-Clad Epoxy Finish 2.0-4.0 (50-100)

Concrete, smooth:

2 cts. Waterbased Tile-Clad Epoxy Finish 2.0-4.0 (50-100)

Galvanized Steel:

1 ct. Waterbased Tile-Clad Epoxy Primer 2.0-4.0 (50-100) 1-2 cts. Waterbased Tile-Clad Epoxy Finish 2.0-4.0 (50-100)

Drywall:

1 ct. ProMar 200 Interior Latex Primer 1.0-1.4 (25-35) 2 cts. Waterbased Tile-Clad Epoxy Finish 2.0-4.0 (50-100)

The systems listed above are representative of the product's use, other systems may be appropriate.

DISCLAIMER

The information and recommendations set forth in this Product Data Sheet are based upon tests conducted by or on behalf of The Sherwin-Williams Company. Such information and recommendations set forth herein are subject to change and pertain to the product offered at the time of publication. Consult your Sherwin-Williams representative to obtain the most recent Product Data Information and Application Bulletin.

Revised 4/12

EPOXY FINISH

PART A B73-100 SERIES

PART B B73V100 HARDENER

Protective

Marine Coatings

4.19 www.sherwin-williams.com/protective

SURFACE PREPARATIONS

Surface must be clean, dry, and in sound condition. Remove all oil, dust, grease, dirt, loose rust, and other foreign material to ensure adequate adhesion.

Do not use hydrocarbon solvents for cleaning.

Iron & Steel Minimum surface preparation is Hand Tool Clean per SSPC-SP2.

Remove all oil and grease from surface by Solvent Cleaning per SSPC-SP1 (recommended preparation is Steam Cleaning). For better performance, use Commercial Blast Cleaning per SSPC- SP6/NACE 3, blast clean all surfaces using a sharp, angular abrasive for optimum surface profi le (2 mils / 50 microns). Prime any bare steel within 8 hours or before fl ash rusting occurs. Primer required.

Masonry and Block For surface preparation, refer to SSPC-SP13/NACE 6, or ICRI No. 310.2, CSP 1-3. Surfaces should be thoroughly clean and dry.

Concrete and mortar must be cured at least 28 days @ 75°F (24oC).

Remove all loose mortar and foreign material. Surface must be free of laitance, concrete dust, dirt, form release agents, moisture curing membranes, loose cement and hardeners. Fill bug holes, air pockets and other voids with Cement-Plex 875. Weathered masonry and soft or porous cement board must be brush blasted or power tool cleaned to remove loosely adhering contamination and to get to a hard, fi rm surface. Laitance must be removed.

Galvanized Steel Allow to weather a minimum of six months prior to coating. Remove all oil, grease, dirt, oxide and other foreign material by Solvent Cleaning per SSPC-SP1 (recommended preparation is Steam Cleaning). When weathering is not possible, or the surface has been treated with chromates or silicates, fi rst Solvent Clean per SSPC-SP1 (recommended preparation is Steam Cleaning) and apply a test patch. Allow paint to dry at least one week before test-ing adhesion. If adhesion is poor, brush blasting per SSPC-SP7 is necessary to remove these treatments. Rusty galvanizing requires a minimum of Hand Tool Cleaning per SSPC-SP2, prime the area the same day as cleaned.

Previously Painted Surfaces If in sound condition, clean the surface of all foreign material.

Smooth, hard or glossy coatings and surfaces should be dulled by abrading the surface. Apply a test area, allowing paint to dry one week before testing adhesion. If adhesion is poor, or if this product attacks the previous fi nish, removal of the previous coating may be necessary. If paint is peeling or badly weathered, clean surface to sound substrate and treat as a new surface as above.

Surface Preparation Standards Condition of Surface

ISO 8501-1

BS7079:A1

Swedish Std.

SIS055900 SSPC NACE

White Metal Sa 3 Sa 3 SP 5 1 Near White Metal Sa 2.5 Sa 2.5 SP 10 2 Commercial Blast Sa 2 Sa 2 SP 6 3 Brush-Off Blast Sa 1 Sa 1 SP 7 4 Hand Tool Cleaning Rusted C St 2 C St 2 SP 2 -

Pitted & Rusted D St 2 D St 2 SP 2 - Power Tool Cleaning Rusted C St 3 C St 3 SP 3 -

Pitted & Rusted D St 3 D St 3 SP 3 -

APPLICATION BULLETIN

APPLICATION CONDITIONS

Temperature: 50°F (10°C) minimum, 100°F (38°C) maximum (air, surface, and material) At least 5°F (2.8°C) above dew point

Relative humidity: 85% maximum

APPLICATION EQUIPMENT

The following is a guide. Changes in pressures and tip sizes may be needed for proper spray characteristics. Always purge spray equipment before use with listed reducer. Any reduction must be compliant with existing VOC regulations and compatible with the existing environmental and application conditions.

Reducer/Clean Up ...........Water

Airless Spray Pressure.........................2000 psi Hose...............................1/4" ID Tip ...................................015" - .017" Filter ...............................60 mesh Reduction .......................As needed up to 10% by volume

Conventional Spray Gun ................................DeVilbiss MBC-510 Fluid Tip .........................E Air Nozzle Atomization Pressure .....40-60 psi Fluid Pressure ................10-20 psi Reduction .......................As needed up to 10% by volume

Brush Brush..............................Nylon/Polyester Reduction .......................Not recommended

Roller Cover .............................3/8" woven with solvent resistant core Reduction .......................Not recommended

If specifi c application equipment is not listed above, equivalent equipment may be substituted.

continued on back

4.19

EPOXY FINISH

PART A B73-100 SERIES

PART B B73V100 HARDENER

Protective

Marine Coatings www.sherwin-williams.com/protective

APPLICATION BULLETIN

APPLICATION PROCEDURES

Surface preparation must be completed as indicated.

Mix contents of each component thoroughly using low speed power agitation. Make certain no pigment remains on the bottom of the can. Then combine four parts by volume of Part A with one part by volume of Part B. Thoroughly agitate the mixture with power agitation. Allow the material to sweat-in as indicated prior to ap-plication. Re-stir before using.

If reducer is used, add only after both components have been thoroughly mixed, after sweat-in.

Apply paint at the recommended fi lm thickness and spreading rate as indicated below:

Recommended Spreading Rate per coat:

Minimum Maximum

Wet mils (microns) 4.5 (112) 9.0 (225) Dry mils (microns) 2.0 (50) 4.0 (100) ~Coverage sq ft/gal (m2/L) 176 (4.3) 352 (8.6) Theoretical coverage sq ft/gal (m2/L) @ 1 mil / 25 microns dft 704 (17.2)

NOTE: Brush or roll application may require multiple coats to achieve maximum fi lm thickness and uniformity of appearance.

Drying Schedule @ 5.0 mils wet (125 microns):

@ 50°F/10°C @ 77°F/25°C @ 100°F/38°C

50% RH

To touch: 1.5 hours 45 minutes 25 minutes To handle: 5.5 hours 4.5 hours 2 hours To recoat:

minimum: 8 hours 6 hours 3 hours maximum: 30 days 30 days 30 days

To cure: 7 days 7 days 7 days If maximum recoat time is exceeded, abrade surface before recoating.

Drying time is temperature, humidity, and fi lm thickness dependent.

Pot Life: 4.5 hours 3.5 hours 1.5 hours Sweat-in-time: 30 minutes 30 minutes 10 minutes

Application of coating above maximum or below minimum recommended spreading rate may adversely affect coating performance.

CLEAN UP INSTRUCTIONS

Clean spills and spatters immediately with soap and warm water.

Clean hands and tools immediately after use with soap and warm water. After cleaning, fl ush spray equipment with Mineral Spirits, R1K4, to prevent rusting of the equipment. Follow manufacturer's safety recommendations when using any solvent.

DISCLAIMER

The information and recommendations set forth in this Product Data Sheet are based upon tests conducted by or on behalf of The Sherwin-Williams Company.

Such information and recommendations set forth herein are subject to change and pertain to the product offered at the time of publication. Consult your Sherwin- Williams representative to obtain the most recent Product Data Information and Application Bulletin.

PERFORMANCE TIPS

Stripe coat all crevices, welds, and sharp angles to prevent early failure in these areas.

When using spray application, use a 50% overlap with each pass of the gun to avoid holidays, bare areas, and pinholes. If necessary, cross spray at a right angle

Spreading rates are calculated on volume solids and do not include an application loss factor due to surface profi le, roughness or po-rosity of the surface, skill and technique of the applicator, method of application, various surface irregularities, material lost during mixing, spillage, overthinning, climatic conditions, and excessive fi lm build.

Excessive reduction of material can affect fi lm build, appearance, and adhesion.

Do not mix previously catalyzed material with new.

Do not apply the material beyond recommended pot life.

In order to avoid blockage of spray equipment, clean equipment before use or before periods of extended downtime with water.

Do not use hydrocarbon solvents for cleaning.

Refer to Product Information sheet for additional performance characteristics and properties.

SAFETY PRECAUTIONS

Refer to the MSDS sheet before use.

Published technical data and instructions are subject to change without notice.

Contact your Sherwin-Williams representative for additional technical data and instructions.

WARRANTY

The Sherwin-Williams Company warrants our products to be free of manufacturing defects in accord with applicable Sherwin-Williams quality control procedures.

Liability for products proven defective, if any, is limited to replacement of the de-fective product or the refund of the purchase price paid for the defective product as determined by Sherwin-Williams. NO OTHER WARRANTY OR GUARANTEE

OF ANY KIND IS MADE BY SHERWIN-WILLIAMS, EXPRESSED OR IMPLIED,

STATUTORY, BY OPERATION OF LAW OR OTHERWISE, INCLUDING MER-

CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

Material Safety Data Sheets

HMIS Codes Health 2*

Flammability 3 Reactivity 0

DATE OF PREPARATION

Nov 4, 2014

MATERIAL SAFETY DATA SHEET

B79W8810 20 00

SECTION 1 — PRODUCT AND COMPANY IDENTIFICATION

PRODUCT NUMBER

B79W8810

PRODUCT NAME

ProBlock® Primer, Interior Oil-Based, White

MANUFACTURER'S NAME

THE SHERWIN-WILLIAMS COMPANY

101 Prospect Avenue N.W.

Cleveland, OH 44115

Telephone Numbers and Websites Product Information www.sherwin-williams.com

Regulatory Information (216) 566-2902 www.paintdocs.com

Medical Emergency (216) 566-2917 Transportation Emergency* (800) 424-9300 for Chemical Emergency ONLY (spill, leak, fire, exposure, or * accident)

SECTION 2 — COMPOSITION/INFORMATION ON INGREDIENTS

% by Weight CAS Number Ingredient Units Vapor Pressure 13 64742-89-8 Lt. Aliphatic Hydrocarbon Solvent

ACGIH TLV 300 PPM 12 mm

OSHA PEL 300 PPM

7 64742-88-7 Mineral Spirits 140-Flash ACGIH TLV 100 PPM 0.5 mm

OSHA PEL 100 PPM

0.4 100-41-4 Ethylbenzene ACGIH TLV 20 PPM 7.1 mm

OSHA PEL 100 PPM

OSHA PEL 125 PPM STEL

2 1330-20-7 Xylene ACGIH TLV 100 PPM 5.9 mm

ACGIH TLV 150 PPM STEL

OSHA PEL 100 PPM

OSHA PEL 150 PPM STEL

7 14808-60-7 Quartz ACGIH TLV 0.025 mg/m3 as Resp. Dust OSHA PEL 0.1 mg/m3 as Resp. Dust

6 14807-96-6 Talc ACGIH TLV 2 mg/m3 as Resp. Dust OSHA PEL 2 mg/m3 as Resp. Dust

4 12001-26-2 Mica ACGIH TLV 3 mg/m3 as Resp. Dust OSHA PEL 3 mg/m3 as Resp. Dust

10 13463-67-7 Titanium Dioxide ACGIH TLV 10 mg/m3 as Dust OSHA PEL 10 mg/m3 Total Dust OSHA PEL 5 mg/m3 Respirable Fraction

SECTION 3 — HAZARDS IDENTIFICATION

ROUTES OF EXPOSURE

INHALATION of vapor or spray mist.

EYE or SKIN contact with the product, vapor or spray mist.

B79W8810

UEL

7.0

LEL

0.9

FLASH POINT

62 °F PMCC

EFFECTS OF OVEREXPOSURE

EYES: Irritation.

SKIN: Prolonged or repeated exposure may cause irritation.

INHALATION: Irritation of the upper respiratory system.

May cause nervous system depression. Extreme overexposure may result in unconsciousness and possibly death.

Prolonged overexposure to hazardous ingredients in Section 2 may cause adverse chronic effects to the following organs or systems:

the liver the urinary system the reproductive system

SIGNS AND SYMPTOMS OF OVEREXPOSURE

Headache, dizziness, nausea, and loss of coordination are indications of excessive exposure to vapors or spray mists.

Redness and itching or burning sensation may indicate eye or excessive skin exposure.

MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE

None generally recognized.

CANCER INFORMATION

For complete discussion of toxicology data refer to Section 11.

SECTION 4 — FIRST AID MEASURES

EYES: Flush eyes with large amounts of water for 15 minutes. Get medical attention.

SKIN: Wash affected area thoroughly with soap and water.

Remove contaminated clothing and launder before re-use.

INHALATION: If affected, remove from exposure. Restore breathing. Keep warm and quiet.

INGESTION: Do not induce vomiting. Get medical attention immediately.

SECTION 5 — FIRE FIGHTING MEASURES

FLAMMABILITY CLASSIFICATION

RED LABEL -- Flammable, Flash below 100 °F (38 °C)

EXTINGUISHING MEDIA

Carbon Dioxide, Dry Chemical, Foam

UNUSUAL FIRE AND EXPLOSION HAZARDS

Closed containers may explode when exposed to extreme heat.

Application to hot surfaces requires special precautions.

During emergency conditions overexposure to decomposition products may cause a health hazard. Symptoms may not be immediately apparent. Obtain medical attention.

SPECIAL FIRE FIGHTING PROCEDURES

Full protective equipment including self-contained breathing apparatus should be used.

Water spray may be ineffective. If water is used, fog nozzles are preferable. Water may be used to cool closed containers to prevent pressure build-up and possible autoignition or explosion when exposed to extreme heat.

SECTION 6 — ACCIDENTAL RELEASE MEASURES

STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED

Remove all sources of ignition. Ventilate the area.

Remove with inert absorbent.

SECTION 7 — HANDLING AND STORAGE

STORAGE CATEGORY

DOL Storage Class IB

PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE

Contents are FLAMMABLE. Keep away from heat, sparks, and open flame.

During use and until all vapors are gone: Keep area ventilated - Do not smoke - Extinguish all flames, pilot lights, and heaters - Turn off stoves, electric tools and appliances, and any other sources of ignition.

Consult NFPA Code. Use approved Bonding and Grounding procedures.

Keep container closed when not in use. Transfer only to approved containers with complete and appropriate labeling. Do not take internally.

Keep out of the reach of children.

SECTION 8 — EXPOSURE CONTROLS/PERSONAL PROTECTION

PRECAUTIONS TO BE TAKEN IN USE

Use only with adequate ventilation.

Avoid contact with skin and eyes. Avoid breathing vapor and spray mist.

Wash hands after using.

This coating may contain materials classified as nuisance particulates (listed "as Dust" in Section 2) which may be present at hazardous levels only during sanding or abrading of the dried film. If no specific dusts are listed in Section 2, the applicable limits for nuisance dusts are ACGIH TLV 10 mg/m3 (total dust), 3 mg/m3 (respirable fraction), OSHA PEL 15 mg/m3 (total dust), 5 mg/m3 (respirable fraction).

Removal of old paint by sanding, scraping or other means may generate dust or fumes that contain lead. Exposure to lead dust or fumes may cause brain damage or other adverse health effects, especially in children or pregnant women. Controlling exposure to lead or other hazardous substances requires the use of proper protective equipment, such as a properly fitted respirator (NIOSH approved) and proper containment and cleanup. For more information, call the National Lead Information Center at 1-800-424-LEAD (in US) or contact your local health authority.

VENTILATION

Local exhaust preferable. General exhaust acceptable if the exposure to materials in Section 2 is maintained below applicable exposure limits. Refer to OSHA Standards 1910.94, 1910.107, 1910.108.

RESPIRATORY PROTECTION

If personal exposure cannot be controlled below applicable limits by ventilation, wear a properly fitted organic vapor/particulate respirator approved by NIOSH/MSHA for protection against materials in Section 2.

When sanding or abrading the dried film, wear a dust/mist respirator approved by NIOSH/MSHA for dust which may be generated from this product, underlying paint, or the abrasive.

PROTECTIVE GLOVES

Wear gloves which are recommended by glove supplier for protection against materials in Section 2.

EYE PROTECTION

Wear safety spectacles with unperforated sideshields.

OTHER PRECAUTIONS

Intentional misuse by deliberately concentrating and inhaling the contents can be harmful or fatal.

SECTION 9 — PHYSICAL AND CHEMICAL PROPERTIES

PRODUCT WEIGHT 12.27 lb/gal 1470 g/l

SPECIFIC GRAVITY 1.48

BOILING POINT 240 - 416 °F 115 - 213 °C

MELTING POINT Not Available

VOLATILE VOLUME 45%

EVAPORATION RATE Slower than ether VAPOR DENSITY Heavier than air

SOLUBILITY IN WATER Not Available VOLATILE ORGANIC COMPOUNDS (VOC Theoretical - As Packaged)

2.91 lb/gal 349 g/l Less Water and Federally Exempt Solvents

2.91 lb/gal 349 g/l Emitted VOC

SECTION 10 — STABILITY AND REACTIVITY

STABILITY — Stable

CONDITIONS TO AVOID

None known.

INCOMPATIBILITY

None known.

HAZARDOUS DECOMPOSITION PRODUCTS

By fire: Carbon Dioxide, Carbon Monoxide

HAZARDOUS POLYMERIZATION

Will not occur

SECTION 11 — TOXICOLOGICAL INFORMATION

CHRONIC HEALTH HAZARDS

Reports have associated repeated and prolonged overexposure to solvents with permanent brain and nervous system damage.

Ethylbenzene is classified by IARC as possibly carcinogenic to humans (2B) based on inadequate evidence in humans and sufficient evidence in laboratory animals. Lifetime inhalation exposure of rats and mice to high ethylbenzene concentrations resulted in increases in certain types of cancer, including kidney tumors in rats and lung and liver tumors in mice. These effects were not observed in animals exposed to lower concentrations. There is no evidence that ethylbenzene causes cancer in humans.

Crystalline Silica (Quartz, Cristobalite) is listed by IARC and NTP. Long term exposure to high levels of silica dust, which can occur only when sanding or abrading the dry film, may cause lung damage (silicosis) and possibly cancer.

IARC's Monograph No. 93 reports there is sufficient evidence of carcinogenicity in experimental rats exposed to titanium dioxide but inadequate evidence for carcinogenicity in humans and has assigned a Group 2B rating. In addition, the IARC summary concludes, "No significant exposure to titanium dioxide is thought to occur during the use of products in which titanium is bound to other materials, such as paint."

TOXICOLOGY DATA

CAS No. Ingredient Name 64742-89-8 Lt. Aliphatic Hydrocarbon Solvent

LC50 RAT 4HR Not Available LD50 RAT Not Available

64742-88-7 Mineral Spirits 140-Flash LC50 RAT 4HR Not Available LD50 RAT Not Available

100-41-4 Ethylbenzene LC50 RAT 4HR Not Available LD50 RAT 3500 mg/kg

1330-20-7 Xylene LC50 RAT 4HR 5000 ppm LD50 RAT 4300 mg/kg

14808-60-7 Quartz LC50 RAT 4HR Not Available LD50 RAT Not Available

14807-96-6 Talc LC50 RAT 4HR Not Available LD50 RAT Not Available

12001-26-2 Mica LC50 RAT 4HR Not Available LD50 RAT Not Available

13463-67-7 Titanium Dioxide LC50 RAT 4HR Not Available LD50 RAT Not Available

SECTION 12 — ECOLOGICAL INFORMATION

ECOTOXICOLOGICAL INFORMATION

No data available.

SECTION 13 — DISPOSAL CONSIDERATIONS

WASTE DISPOSAL METHOD

Waste from this product may be hazardous as defined under the Resource Conservation and Recovery Act (RCRA) 40 CFR 261.

Waste must be tested for ignitability to determine the applicable EPA hazardous waste numbers.

Incinerate in approved facility. Do not incinerate closed container. Dispose of in accordance with Federal, State/Provincial, and Local regulations regarding pollution.

SECTION 14 — TRANSPORT INFORMATION

Multi-modal shipping descriptions are provided for informational purposes and do not consider container sizes. The presence of a shipping description for a particular mode of transport (ocean, air, etc.), does not indicate that the product is packaged suitably for that mode of transport. All packaging must be reviewed for suitability prior to shipment, and compliance with the applicable regulations is the sole responsibility of the person offering the product for transport.

US Ground (DOT) 5 Liters (1.3 Gallons) and Less may be Classed as LTD. QTY. (PAINT OR RELATED).

Larger Containers are Regulated as:

UN1263, PAINT, 3, PG II, (ERG#128)

DOT (Dept of Transportation) Hazardous Substances & Reportable Quantities Xylenes (isomers and mixture) 100 lb RQ

Bulk Containers may be Shipped as (check reportable quantities):

UN1263, PAINT, 3, PG II, (ERG#128)

Canada (TDG)

UN1263, PAINT, CLASS 3, PG II, LIMITED QUANTITY, (ERG#128)

IMO

5 Liters (1.3 Gallons) and Less may be Shipped as Limited Quantity.

UN1263, PAINT, CLASS 3, PG II, (17 C c.c.), EmS F-E, S-E

IATA/ICAO

UN1263, PAINT, 3, PG II

SECTION 15 — REGULATORY INFORMATION

SARA 313 SUPPLIER NOTIFICATION(40 CFR 372.65C)

CAS No. CHEMICAL/COMPOUND % by WT % Element 100-41-4 Ethylbenzene 0.3 1330-20-7 Xylene 2

CALIFORNIA PROPOSITION 65

WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

TSCA CERTIFICATION

All chemicals in this product are listed, or are exempt from listing, on the TSCA Inventory.

SECTION 16 — OTHER INFORMATION

This product has been classified in accordance with the hazard criteria of the Canadian Controlled Products Regulations (CPR) and the MSDS contains all of the information required by the CPR.

The above information pertains to this product as currently formulated, and is based on the information available at this time. Addition of reducers or other additives to this product may substantially alter the composition and hazards of the product. Since conditions of use are outside our control, we make no warranties, express or implied, and assume no liability in connection with any use of this information.

HMIS Codes Health 2*

Flammability 0 Reactivity 0

DATE OF PREPARATION

Jul 25, 2013

MATERIAL SAFETY DATA SHEET

B73W111 07 00

SECTION 1 — PRODUCT AND COMPANY IDENTIFICATION

PRODUCT NUMBER

B73W111

PRODUCT NAME

Waterbased TILE-CLAD® Epoxy Finish (Part A), Extra White

MANUFACTURER'S NAME

THE SHERWIN-WILLIAMS COMPANY

101 Prospect Avenue N.W.

Cleveland, OH 44115

Telephone Numbers and Websites Product Information (800) 524-5979 www.sherwin-williams.com Regulatory Information (216) 566-2902 www.paintdocs.com Medical Emergency (216) 566-2917

Transportation Emergency* (800) 424-9300 for Chemical Emergency ONLY (spill, leak, fire, exposure, or * accident)

SECTION 2 — COMPOSITION/INFORMATION ON INGREDIENTS

% by Weight CAS Number Ingredient Units Vapor Pressure 6 2807-30-9 2-Propoxyethanol

ACGIH TLV Not Available 1.3 mm OSHA PEL Not Available

35 25068-38-6 Epoxy Polymer ACGIH TLV Not Available OSHA PEL Not Available

22 13463-67-7 Titanium Dioxide ACGIH TLV 10 mg/m3 as Dust OSHA PEL 10 mg/m3 Total Dust OSHA PEL 5 mg/m3 Respirable Fraction

SECTION 3 — HAZARDS IDENTIFICATION

ROUTES OF EXPOSURE

INHALATION of vapor or spray mist.

EYE or SKIN contact with the product, vapor or spray mist.

EFFECTS OF OVEREXPOSURE

EYES: Irritation.

SKIN: Prolonged or repeated exposure may cause irritation.

INHALATION: Irritation of the upper respiratory system.

In a confined area vapors in high concentration may cause headache, nausea or dizziness.

SIGNS AND SYMPTOMS OF OVEREXPOSURE

Redness and itching or burning sensation may indicate eye or excessive skin exposure.

MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE

May cause allergic skin reaction in susceptible persons or skin sensitization.

CANCER INFORMATION

For complete discussion of toxicology data refer to Section 11.

B73W111

UEL

Not Applicable

LEL

Not Applicable

FLASH POINT

Not Applicable

SECTION 4 — FIRST AID MEASURES

EYES: Flush eyes with large amounts of water for 15 minutes. Get medical attention.

SKIN: Wash affected area thoroughly with soap and water.

If irritation persists or occurs later, get medical attention.

Remove contaminated clothing and launder before re-use.

INHALATION: If affected, remove from exposure. Restore breathing. Keep warm and quiet.

INGESTION: Do not induce vomiting. Get medical attention immediately.

SECTION 5 — FIRE FIGHTING MEASURES

FLAMMABILITY CLASSIFICATION

Not Applicable

EXTINGUISHING MEDIA

Carbon Dioxide, Dry Chemical, Alcohol Foam

UNUSUAL FIRE AND EXPLOSION HAZARDS

Closed containers may explode (due to the build-up of pressure) when exposed to extreme heat.

During emergency conditions overexposure to decomposition products may cause a health hazard. Symptoms may not be immediately apparent. Obtain medical attention.

SPECIAL FIRE FIGHTING PROCEDURES

Full protective equipment including self-contained breathing apparatus should be used.

Water spray may be ineffective. If water is used, fog nozzles are preferable. Water may be used to cool closed containers to prevent pressure build-up and possible autoignition or explosion when exposed to extreme heat.

SECTION 6 — ACCIDENTAL RELEASE MEASURES

STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED

Remove all sources of ignition. Ventilate the area.

Remove with inert absorbent.

SECTION 7 — HANDLING AND STORAGE

STORAGE CATEGORY

Not Applicable

PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE

Keep container closed when not in use. Transfer only to approved containers with complete and appropriate labeling. Do not take internally.

Keep out of the reach of children.

SECTION 8 — EXPOSURE CONTROLS/PERSONAL PROTECTION

PRECAUTIONS TO BE TAKEN IN USE

Use only with adequate ventilation.

Avoid contact with skin and eyes. Avoid breathing vapor and spray mist.

Wash hands after using.

This coating may contain materials classified as nuisance particulates (listed "as Dust" in Section 2) which may be present at hazardous levels only during sanding or abrading of the dried film. If no specific dusts are listed in Section 2, the applicable limits for nuisance dusts are ACGIH TLV 10 mg/m3 (total dust), 3 mg/m3 (respirable fraction), OSHA PEL 15 mg/m3 (total dust), 5 mg/m3 (respirable fraction).

VENTILATION

Local exhaust preferable. General exhaust acceptable if the exposure to materials in Section 2 is maintained below applicable exposure limits. Refer to OSHA Standards 1910.94, 1910.107, 1910.108.

RESPIRATORY PROTECTION

If personal exposure cannot be controlled below applicable limits by ventilation, wear a properly fitted organic vapor/particulate respirator approved by NIOSH/MSHA for protection against materials in Section 2.

When sanding or abrading the dried film, wear a dust/mist respirator approved by NIOSH/MSHA for dust which may be generated from this product, underlying paint, or the abrasive.

PROTECTIVE GLOVES

Wear gloves which are recommended by glove supplier for protection against materials in Section 2.

EYE PROTECTION

Wear safety spectacles with unperforated sideshields.

OTHER PROTECTIVE EQUIPMENT

Use of barrier cream on exposed skin is recommended.

OTHER PRECAUTIONS

This product must be mixed with other components before use. Before opening the packages, READ AND FOLLOW WARNING LABELS ON

ALL COMPONENTS.

SECTION 9 — PHYSICAL AND CHEMICAL PROPERTIES

PRODUCT WEIGHT 10.60 lb/gal 1270 g/l

SPECIFIC GRAVITY 1.28

BOILING POINT 212 - 500 °F 100 - 260 °C

MELTING POINT Not Available

VOLATILE VOLUME 53%

EVAPORATION RATE Slower than ether VAPOR DENSITY Heavier than air

SOLUBILITY IN WATER Not Available pH 9.0

VOLATILE ORGANIC COMPOUNDS (VOC Theoretical - As Packaged)

1.75 lb/gal 210 g/l Less Water and Federally Exempt Solvents

1.05 lb/gal 126 g/l Emitted VOC

SECTION 10 — STABILITY AND REACTIVITY

STABILITY — Stable

CONDITIONS TO AVOID

None known.

INCOMPATIBILITY

None known.

HAZARDOUS DECOMPOSITION PRODUCTS

By fire: Carbon Dioxide, Carbon Monoxide

HAZARDOUS POLYMERIZATION

Will not occur

SECTION 11 — TOXICOLOGICAL INFORMATION

CHRONIC HEALTH HAZARDS

IARC's Monograph No. 93 reports there is sufficient evidence of carcinogenicity in experimental rats exposed to titanium dioxide but inadequate evidence for carcinogenicity in humans and has assigned a Group 2B rating. In addition, the IARC summary concludes, "No significant exposure to titanium dioxide is thought to occur during the use of products in which titanium is bound to other materials, such as paint."

TOXICOLOGY DATA

CAS No. Ingredient Name 2807-30-9 2-Propoxyethanol

LC50 RAT 4HR Not Available LD50 RAT 3090 mg/kg

25068-38-6 Epoxy Polymer LC50 RAT 4HR Not Available LD50 RAT Not Available

13463-67-7 Titanium Dioxide LC50 RAT 4HR Not Available LD50 RAT Not Available

SECTION 12 — ECOLOGICAL INFORMATION

ECOTOXICOLOGICAL INFORMATION

No data available.

SECTION 13 — DISPOSAL CONSIDERATIONS

WASTE DISPOSAL METHOD

Waste from this product is not hazardous as defined under the Resource Conservation and Recovery Act (RCRA) 40 CFR 261.

Incinerate in approved facility. Do not incinerate closed container. Dispose of in accordance with Federal, State/Provincial, and Local regulations regarding pollution.

SECTION 14 — TRANSPORT INFORMATION

Multi-modal shipping descriptions are provided for informational purposes and do not consider container sizes. The presence of a shipping description for a particular mode of transport (ocean, air, etc.), does not indicate that the product is packaged suitably for that mode of transport. All packaging must be reviewed for suitability prior to shipment, and compliance with the applicable regulations is the sole responsibility of the person offering the product for transport.

US Ground (DOT) Not Regulated for Transportation.

Canada (TDG) Not Regulated for Transportation.

IMO

Not Regulated for Transportation.

IATA/ICAO

Not Regulated for Transportation.

SECTION 15 — REGULATORY INFORMATION

SARA 313 SUPPLIER NOTIFICATION(40 CFR 372.65C)

CAS No. CHEMICAL/COMPOUND % by WT % Element

Glycol Ethers 6

CALIFORNIA PROPOSITION 65

WARNING: This product contains chemicals known to the State of California to cause cancer.

TSCA CERTIFICATION

All chemicals in this product are listed, or are exempt from listing, on the TSCA Inventory.

SECTION 16 — OTHER INFORMATION

This product has been classified in accordance with the hazard criteria of the Canadian Controlled Products Regulations (CPR) and the MSDS contains all of the information required by the CPR.

The above information pertains to this product as currently formulated, and is based on the information available at this time. Addition of reducers or other additives to this product may substantially alter the composition and hazards of the product. Since conditions of use are outside our control, we make no warranties, express or implied, and assume no liability in connection with any use of this information.