Medallist Filter.pdf

Culligan Medallist®

& Medallist Plus Series®

Automatic Water Filter

Owners Guide

Thank You

And Welcome To Your New World Of Better Living With Culligan Water.

The Culligan Medallist Plus Series® with Cullar® filter has been tested and certified by WQA against WQA S-200 for the effective reduction of chlorine taste and odor up to 180,000 gallons as verified and substantiated by test data.

The Culligan Medallist Plus Series with Cullneu® filter has been tested and certified by WQA against WQA S-200 for neutralization up to 21,750 gallons as verified and substantiated by test data.

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

For installations in Massachusetts, the Commonwealth of Massachusetts Plumbing Code 248 CMR shall be adhered to. Consult your licensed plumber for installation of the system. This system and its installation must comply with state and local regulations.

If this is your first experience having filtered, conditioned water in your home, you’ll be amazed at the marvelous difference it makes. We promise that you’ll never want to be without it again.

Congratulations, too, on selecting one of the “first family” of water filters in the prestigious Culligan Medallist Series. With Culligan’s many years of knowledge and experience in water treatment, you can be confident that the model you selected has been designed and engineered to provide years of service with a minimum of care and attention.

Products manufactured and marketed by Culligan International Company (Culligan) and its affiliates are protected by patents issued or pending in the United States and other countries. Culligan reserves the right to change the specifications referred to in this literature at any time, without prior notice.

Culligan, Culligan Medallist Series, Cullar, Filtr-Cleer, Cullneu, Accusoft, Culligan Man and www.

culligan.com are trademarks of Culligan International Company or its affiliates.

Performance Data Sheets are included in this manual for various Culligan Medallist Series® Filter models. Refer to the Performance Data Sheet for your specific filter, as there are slight differences between the models. The filter warranty is located on page 17 of this Owner’s Guide.

Filter Model

Medallist 8“ Medallist 10” Medallist Plus 10” General Mineral Tank Size1 8 x 44 in. 10 x 54 in. 10 x 54 in.

Control 3/4” Power Valve 3/4” Power Valve 1” Power Valve Timer Electronic Electronic Electronic Temperature Limits 33-120°F 33-120°F 33-120°F Water Pressure Limits 20-120 psi 20-120 psi 20-120 psi Water Pressure Limits (Canada) 20-90 psi 20-90 psi 20-90 psi Electrical Requirements 24V/60 Hz 24V/60 Hz 24V/60 Hz Electrical Power Consumption, Min./Max. 3 Watts/35 Watts 3 Watts/35 Watts 3 Watts/35 Watts Filtr-Cleer®

Rated Service Flow 7.8 gpm 8.9 gpm 12.0 gpm @ Initial Pressure Drop @ 15 psi @ 15 psi @ 15 psi Minimum Practical Filtration Size 10 microns 10 microns 10 microns Maximum Particulate Matter 150 NTU 150 NTU 150 NTU Maximum Suspended Solids 150 mg/L 150 mg/L 150 mg/L Drain Flow, Maximum3 4.5 gpm 7.0 gpm 7.0 gpm pH Limitation 6.0 - 9.5 6.0 - 9.5 6.0 - 9.5 Recharge Time4 80 min. 80 min. 30 min.

Recharge Water Consumption, Av.5 100 gal. 115 gal. 140 gal.

Freeboard2 10.5 ± 1 inches 11.5 ± 1 inches 19 ± 1.5 inches Height Overall 51 in. 63 in. 60 in.

Cullar®

Rated Service Flow 4.0 gpm 4.0 gpm 6.0 gpm @ Pressure Drop @ 5.0 psi @ 5.0 psi @ 6.0 psi Drain Flow, Maximum3 2 gpm 6.0 gpm 6.0 gpm pH Limitation 5.0 - 11.0 5.0 - 11.0 5.0 - 11.0 Recharge Time4 80 min. 80 min. 30 min.

Recharge Water Consumption, Av.5 53 gal. 83 gal. 110 gal.

Cullar Media Volume 0.75 cu. ft. 1.0 cu. ft. 1.5 cu. ft.

Cullsan® Underbedding Media Amount 10 lbs. (.1 ft3) 20 lbs. (.2 ft3) 20 lbs. (.2 ft3) Freeboard2 14 ± 1 inches 24 ± 1 inches 24 ± 1.5 inches Height Overall 51 in. 63 in. 60 in.

Rated Capacity 100,000 gallons 130,000 gallons 180,000 gallons Cullneu®

Rated Service Flow 2.7 gpm 4.0 gpm 6.0 gpm @ Pressure Drop @ 3.0 psi @ 4.0 psi @ 5.0 psi Drain Flow, Maximum3 3.5 gpm 6.0 gpm 6.0 gpm pH Limitation* 5.8 - 6.2 5.8 - 6.2 5.2 - 6.8 Recharge Time4 80 min. 80 min. 30 min.

Recharge Water Consumption, Av.5 53 gal. 83 gal. 110 gal.

Cullneu Media Volume 1.0 cu. ft. 1.5 cu. ft. 1.6 cu. ft.

Freeboard2 11 ± 1 inches 21 ± 1 inches 18 ± 1.5 inches Height Overall 51 in. 63 in. 60 in.

* Under dynamic conditions, it may be necessary to mix five parts Cullneu with one part Cullneu C to effectively raise the pH. The combination of Cullneu and Cullneu C is not certified by WQA.

Specifications

Filtr-Cleer®

The Filtr-Cleer Automatic Water Filter is capable of reducing particulate matter down to 10 microns particle size. It will not remove color, organics, colloidal turbidity or dissolved solids. Some applications follow:

NOTE: If sands cannot be reduced from the Filtr-Cleer tank during backwashing, a sand trap should be installed.

• After the retention tank when a Cul-Cleer® system is used to correct hydrogen sulfide or colloidal suspension problems.

The quality and number of gallons filtered water between backwashes will depend upon the amount, type, and size of the particulate matter being filtered. If a water sample is sent to our laboratory, where application of a Filtr-Cleer unit is contemplated, write “Filtr-Cleer Analysis” on the sample tag. Send an additional sample of water for a standard water analysis. The laboratory will test for Nephelometric Turbidity Units (NTU) and suspended solids (mg/L). The sample will also be filtered through 10 micron filter paper and NTU run on a filtered sample. If the NTU of the raw water exceeds 150, suspended solids exceed 150 mg/L or the filtered water through the 10 micron filter paper is of an unacceptable quality, a Filtr-Cleer filter may not be applicable. As a guide, the U.S. Public Health Drinking Water standards states the turbidity should not exceed 1 NTU. The exact number of gallons filtered between backwashes cannot be given because of many variables.

Cullar® Filter Medallist Water Filter with Cullar Media will reduce chlorine taste and odor and other common bad tastes and odors, and will also reduce most objectional organic colors. It will not remove hydrogen sulfide. It is important to note that whenever the cause of an objectionable taste or odor has not been established, Health Authorities should determine if water is safe to drink. If bacterial contamination is present, a Cul-Cleer system is indicated. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

Cullneu® Filter Medallist Water Filter with Cullneu Media will neutralize slightly acid water (pH of 5.8 - 6.2) and thus help to prevent unsightly brown or green stains due to corrosion of household plumbing. If the pH is from 5 to 6, one part of Cullneu C media should be mixed with 5 parts of Cullneu media to provide additional neutralizing capability. If the water to be treated has a pH less than 5, a high hardness, or a high carbon dioxide level, Cullneu may not be applicable; a solution feeder should be used. Since Cullneu adds hardness, it should be used prior to a softener.

In order to size and apply the equipment correctly, a complete analysis of the water supply should be obtained. This can best be accomplished by contacting your local Culligan dealer, who will be able to test the water supply right at the site, or arrange to have one or more water samples sent to the Culligan laboratory for a more detailed analysis.

Introduction

Power Loss The AccuSoft® circuit board is equipped with a Hi-Cap Capacitor and EEPROM memory chip. The capacitor is capable of maintaining the time, for at least two days, in the event of a power outage.

The EEPROM ensures that the individual programming parameters of your filter are not lost.

If the power outage lasts long enough to drain the Hi-Cap Capacitor, the control will flash “12:00 PM” when power is returned to the control. The unit will continue to keep time from the moment power is restored, and will initiate a full regeneration at the preset regeneration time. The time of day will need to be reset in order to return the regeneration to its preset time.

If you live in an area where power outages occur with a regular frequency, a battery backup option is available for ensuring that the time of day is properly maintained. Contact your Culligan Dealer for more information.

Regeneration To initiate a regeneration at the preset time, press the “REGEN” button. The “REG” light will light. To initiate an immediate regeneration, press and hold the “REGEN” button for at least five seconds. The “REG” will light and blink. An immediate regeneration will also occur if a power outage has lasted for more than four hours and the Immediate Regeneration option is chosen. Ask your Culligan Dealer about this feature.

A regeneration at the Time of Regeneration will occur if so signaled by the Soft-Minder meter. The “REG” enunciator on the display will also be lit.

Service The Culligan Medallist Series® water filter is equipped with a self diagnostic program to insure optimal operation of your water filter. Should service become necessary, a phone icon will appear in the display. If this condition occurs, call your local Culligan Dealer for assistance. The phone icon and error code will be the only items displayed when service is required on the control.

Familiarization

Setting the Microprocessor The microprocessor senses when it is installed as a Soft-Minder® control. Adding or removing any connection to the board will automatically reset the microprocessor to the factory settings.

Step 1 – Programming Time of Day Press the “STATUS” key.

The display will blink “tod” for 3 seconds and then change to time of day with the “minutes” digits blinking.

Adjust the “minutes” digits with the “+” or “-” keys.

Press the “REGEN” key to blink the “hours” digits.

Adjust the “hours” digits with the “+” or “-” keys.

Press the “REGEN” key to cycle back to “minutes” Note: The “hours” setting scrolls through 1-12 and 1-12 PM. Make sure the proper AM or PM indicator is shown when setting the time (AM is not displayed).

Step 2 – Programming Regeneration Time Press the “Status” key after setting the time of day.

The display will blink “tor” for 3 seconds and then change to the time setting with the “ones” digit blinking.

Adjust regeneration time as time of day above.

Note: This option will not show if the “dIP 2” option is set to immediate

Step 3 – Programming Backwash Time Press the “Status” key after programming “tor”.

The display will blink “bw” for 3 seconds and then display the backwash time in minutes.

Adjust the setting with “+” or “-” key. (1-40 minutes)

Step 4 – Programming Fast Rinse Time Press the “STATUS” key after programming the backwash time. The display will blink “Fr” for 3 seconds and then display the Fast Rinse Time in minutes.

Adjust the setting with “+” or “-” key. (5-30 minutes)

Programming

12:00PM

2:00

Step 5 – Days to Regeneration with Fast Rinse Press the “STATUS” key after programming the fast rinse time.

The display will blink “CAP” for 3 seconds and then display the number of days between regenerations.

Adjust the setting with the “+” or “-” key. (1-42 days)

Exiting Program Mode From Step 5 press the “Status” key.

The display will go blank.

Press the “Status” key again to exit programming.

Note: The control will exit the programming mode if no key press activity takes place within one minute.

Troubleshooting The Culligan Medallist Series Filter is equipped with an advanced error detection system. During all operating modes the filter’s electronics are performing self-diagnostics to ensure that the unit is operating correctly. There may be times, however, when something may occur that could cause the unit to improperly operate. In those instances the microprocessor will identify the exact problem and alert the user with a telephone handset symbol in the upper left corner of the display and the error code will be shown. Shown below is codes that would appear if an error is detected.

Display Error Description Response

E1 Motor will not stop turning Call Culligan service technician

E2 Motor stuck Call Culligan service technician

E3 Wrong position Call Culligan service technician

If an error code appears that requires an authorized service technician please contact your local Culligan Dealer.

For any additional troubleshooting or service needs please contact your local Culligan Dealer.

Programming (cont.)

If you unexpectedly experience problem water, make these simple checks before calling your Culligan dealer. One of the following conditions may be the reason for your interruption of service.

Important If any of the following conditions is found, the water filter should be manually recharged according to instructions on page 5 after you have corrected the problem.

Power Supply Check your power supply cord. Is it plugged fully into the electric outlet? Be certain that the outlet is not controlled by a wall switch which has been turned off. Reset conditioner to proper time of day and then plug in.

Blown Fuse Check the house fuse or circuit breaker panel. Replace a blown-out fuse or reset an open circuit breaker.

Power Failure Any interruption in your power supply or time changes - such as daylight savings - will disrupt your filter’s recharge schedule by causing the timer to run off-schedule. Reset timer to proper time of day.

Bypass Valves Check to see if they are in the proper position. Cul-Flo-Valv® Bypass, if used, should be in the “Push for Service” position. If hand valves are used, see that inlet and outlet valve are opened and that the bypass valve is closed.

No Water If you aren’t getting any water flow at all, make sure your water supply is working. Open a tap ahead of the filter (outside tap) to see if you have any water pressure. If you have water pressure, check the bypass valve. If it is in the Service position, put it into the bypass and call your Culligan dealer for service.

Increased Usage Guests, family additions, new water-using appliances, etc., all will result in more water usage and will require more capacity from your filter. You can reprogram your recharging schedule by following the directions on pages 7 and 8. Call your Culligan dealer for advice and save a service call.

Things to Check Before You Call For Service

Normally, all water except outside lines passes through the water filter. There are times when the water filter should be bypassed, using the push-button Cul-Flo-Valv® Bypass, or a 3-way bypass valve.

You should bypass:

1. If lines to outside faucets do not bypass the water filter, and you do not want to waste filtered water on lawn sprinkling or other outside uses.

Medallist Series Bypass Valve Culligan Bypass Valve In the back of Culligan water conditioners is a push-button Cul-Flo- Valv® Bypass. To bypass unit, simply turn the blue knob clockwise. To return to soft water service, reverse the procedure - turn the blue knob counter-clockwise.

To BYPASS, turn the blue knob clockwise (see directional arrow on end of knob) until the knob stops as shown.

DO NOT OVERTIGHTEN!

To return to SERVICE, turn the blue knob counter-clockwise (see directional arrow on end of knob) until the knob stops as shown.

DO NOT OVERTIGHTEN!

When & How to Bypass

Your Water Filter

Bypassed

About 1-1/4”

A screwdriver shank may be used in the slot as a lever for extra turning force if needed.Soft Water

Culligan Medallist Plus Series® 10” With Cullneu® Filter Important Notice — Read this data sheet and compare the capabilities of the unit to your actual water treatment needs. Culligan recommends that you have your water supply tested to determine these needs before purchasing a water treatment unit.

Culligan knows the more informed you are about your water treatment system, the more confident you will be about its performance. It’s because of this and more than seventy years of commitment to our customers that Culligan is providing this Performance Data Sheet to its customers.

Substance Reduction

This system has been tested according to WQA S-200 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in

WQA S-200.

While testing was performed under standard laboratory conditions, actual performance may vary.

Substance USEPA SDWA* SMCL Average Test Influent Concentration Level

Average Test Effluent Concentration Level pH 6.5 - 8.5 4.6 mg/L 7.1 mg/L

* United States Environmental Protection Agency Safe Drinking Water Act.

Operating Conditions

This filter is tested and certified by WQA against WQA S-200 for neutralization up to 21,750 gallons for the Medallist Plus 10” Cullneu as verified and substantiated by test data.

Performance Indicator: If water flow decreases or a noticeable taste change occurs, the filter should be backwashed. If conditions do not improve, contact your local Culligan Man. He can determine if your filter requires servicing. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

Regeneration Frequency: Replacement frequency will vary with water conditions.

Refer to the Installation and Operation Instructions, Parts List and Printed Warranties for more specific product information. To avoid contamination from improper handling and installation, your system should only be installed and serviced by your Culligan Man. Performance will vary based on local water conditions. The substances reduced by this product are not necessarily in your water.

Buyer Signature __________________________________________________ Date _ ________________

Seller Signature __________________________________________________ Date _ ________________

Performance Data Sheet

Performance

(cont.)

Culligan Medallist Plus Series® 10” With Cullar® Filter Important Notice — Read this data sheet and compare the capabilities of the unit to your actual water treatment needs. Culligan recommends that you have your water supply tested to determine these needs before purchasing a water treatment unit.

Culligan knows the more informed you are about your water treatment system, the more confident you will be about its performance. It’s because of this and more than seventy years of commitment to our customers that Culligan is providing this Performance Data Sheet to its customers.

Substance Reduction

This system has been tested according to WQA S-200 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in

WQA S-200.

While testing was performed under standard laboratory conditions, actual performance may vary.

Substance USEPA SDWA* SMCL Average Test Influent Concentration Level

Average Test Effluent Concentration Level

Chlorine Taste & Odor N/A 2.11 mg/L 0.02 mg/L

* United States Environmental Protection Agency Safe Drinking Water Act.

Operating Conditions

This filter is tested and certified by WQA against WQA S-200 for neutralization up to 180,000 gallons for the Medallist Plus 10” Cullar as verified and substantiated by test data.

Performance Indicator: If water flow decreases or a noticeable taste change occurs, the filter should be backwashed. If conditions do not improve, contact your local Culligan Man. He can determine if your filter requires servicing. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

Regeneration Frequency: Replacement frequency will vary with water conditions.

Refer to the Installation and Operation Instructions, Parts List and Printed Warranties for more specific product information. To avoid contamination from improper handling and installation, your system should only be installed and serviced by your Culligan Man. Performance will vary based on local water conditions. The substances reduced by this product are not necessarily in your water.

Buyer Signature __________________________________________________ Date _ ________________

Seller Signature __________________________________________________ Date _ ________________

(cont.)

Culligan Medallist Series® 8” and 10” With Cullneu® Filter Important Notice — Read this data sheet and compare the capabilities of the unit to your actual water treatment needs. Culligan recommends that you have your water supply tested to determine these needs before purchasing a water treatment unit.

Culligan knows the more informed you are about your water treatment system, the more confident you will be about its performance. It’s because of this and more than seventy years of commitment to our customers that Culligan is providing this Performance Data Sheet to its customers.

Substance Reduction

This system has been tested according to WQA S-200 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in

WQA S-200.

While testing was performed under standard laboratory conditions, actual performance may vary.

Substance USEPA SDWA* SMCL Average Test Influent Concentration Level

Average Test Effluent Concentration Level pH 6.5 - 8.5 4.3 mg/L 8.0 mg/L

* United States Environmental Protection Agency Safe Drinking Water Act.

Operating Conditions

Performance Indicator: If water flow decreases or a noticeable taste change occurs, the filter should be backwashed. If conditions do not improve, contact your local Culligan Man. He can determine if your filter requires servicing. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

Regeneration Frequency: Replacement frequency will vary with water conditions.

Refer to the Installation and Operation Instructions, Parts List and Printed Warranties for more specific product information. To avoid contamination from improper handling and installation, your system should only be installed and serviced by your Culligan Man. Performance will vary based on local water conditions. The substances reduced by this product are not necessarily in your water.

(cont.)

Culligan Medallist Series® 8” and 10” With Cullar® Filter Important Notice — Read this data sheet and compare the capabilities of the unit to your actual water treatment needs. Culligan recommends that you have your water supply tested to determine these needs before purchasing a water treatment unit.

Culligan knows the more informed you are about your water treatment system, the more confident you will be about its performance. It’s because of this and more than seventy years of commitment to our customers that Culligan is providing this Performance Data Sheet to its customers.

Substance Reduction

This system has been tested according to WQA S-200 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in

WQA S-200.

While testing was performed under standard laboratory conditions, actual performance may vary.

Substance USEPA SDWA* SMCL Average Test Influent Concentration Level

Average Test Effluent Concentration Level

Chlorine Taste & Odor N/A 2.11 mg/L 0.02 mg/L

* United States Environmental Protection Agency Safe Drinking Water Act.

Operating Conditions

Performance Indicator: If water flow decreases or a noticeable taste change occurs, the filter should be backwashed. If conditions do not improve, contact your local Culligan Man. He can determine if your filter requires servicing. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

Regeneration Frequency: Replacement frequency will vary with water conditions.

Refer to the Installation and Operation Instructions, Parts List and Printed Warranties for more specific product information. To avoid contamination from improper handling and installation, your system should only be installed and serviced by your Culligan Man. Performance will vary based on local water conditions. The substances reduced by this product are not necessarily in your water.

(cont.)

Culligan Medallist Series® 8” and 10” With Filtr-Cleer® Filter Important Notice — Read this data sheet and compare the capabilities of the unit to your actual water treatment needs. Culligan recommends that you have your water supply tested to determine these needs before purchasing a water treatment unit.

Culligan knows the more informed you are about your water treatment system, the more confident you will be about its performance. It’s because of this and more than seventy years of commitment to our customers that Culligan is providing this Performance Data Sheet to its customers.

Substance Reduction

This system has been tested according to WQA S-200 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in

WQA S-200.

While testing was performed under standard laboratory conditions, actual performance may vary.

Substance Average Influent Challenge Concentration

Reduction Required

Average % Reduction

Minimum % Reduction

Class III Particulate Particles > 5 - < 15 µm

45,746 particles/mL > 85% 91.8% 88.8%

Rated Service Flow at Pressure Drop:

7.8 gpm @ 15 psi (8” Filter) 9.0 gpm @ 15 psi (10” Filter)

Operating Conditions

Performance Indicator: If water flow decreases or a noticeable taste change occurs, the filter should be backwashed. If conditions do not improve, contact your local Culligan Man. He can determine if your filter requires servicing. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

Regeneration Frequency: Replacement frequency will vary with water conditions.

Refer to the Installation and Operation Instructions, Parts List and Printed Warranties for more specific product information. To avoid contamination from improper handling and installation, your system should only be installed and serviced by your Culligan Man. Performance will vary based on local water conditions. The substances reduced by this product are not necessarily in your water.

Records and Data

Important Data on Your Water Filter It is advisable to have the salesperson or installer fill in the information below for your future reference.

If this has not been done, please ask for it, as it is necessary if you contact your dealer.

Identification

Model Name ______________________________ Catalog No. ________________________________

Control Model No. _________________________ Control Serial No. ___________________________

Date of Installation __________________________ Tank Serial No. _ ____________________________

Settings

Time of Recharge: _____________ a.m. ________________ p.m.

Regeneration Interval ________________ days (Time clock models)

Gallons to signal ________________ gallons (Soft-Minder® models)

Number of people in household ___________________________________________________________

Water Analysis

Total Hardness __________ (gpg) Total Iron __________ (ppm) pH (acidity)_______________

Other __________________________________________________________________________________

Culligan Limited Warranty

Culligan Medallist Series® Automatic Water Conditioners

You have just purchased one of the finest water conditioners made. As an expression of our confidence in Culligan International Company products, your water conditioner is warranted to the original end-user, when installed in accordance with Culligan specifications, against defects in material and work manship from the date of original installation, as follows:

meter, if so equipped.

For a period of TEN YEARS The control valve body, excluding internal parts.

The conditioner tank

If a part described above is found defective within the specified period, you should notify your inde pendently operated Culligan dealer and arrange a time during normal business hours for the dealer to inspect the water conditioner on your premises. Any part found defective within the terms of this warranty will be repaired or replaced by the dealer. You pay only freight from our factory and local dealer charges.

We are not responsible for damage caused by accident, fire, flood, freezing, Act of God, misuse, misapplication, neglect, oxidizing agents (such as chlorine, ozone, chloramines and other related components), alteration, installation or operation contrary to our printed instructions, or by the use of accessories or components which do not meet Culligan specifications, is not covered by this warranty.

Refer to the specifications section in the Installation and Operating manual for application parameters.

Our product performance specifications are furnished with each water conditioning unit. To the extent permitted by law, culligan disclaims all implied warranties, including without limitation warranties of merchantability and fitness for particular purpose; to the extent required by law, any such implied warranties are limited in duration to the one-year period specified above for the entire conditioner. As a manufacturer, we do not know the characteristics of your water supply or the purpose for which you are purchasing a water conditioner. The quality of water supplies may vary seasonally or over a period of time, and your water usage rate may vary as well. Water characteristics can also differ considerably if your water conditioner is moved to a new location. For these reasons, we assume no liability for the determination of the proper equipment necessary to meet your requirements, and we do not authorize others to assume such obligations for us. Further, we assume no liability and extend no warranties, express or implied, for the use of this product with a non-potable water source. Our obligations under this warranty are limited to the repair or replacement of the failed parts of the water conditioner, and we assume no liability whatsoever for direct, indirect, incidental, consequential, special, general, or other damages.

Some states do not allow the exclusion of implied warranties or limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Similarly, some states do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Consult your telephone directory for your local independently operated Culligan dealer, or write Culligan International Company for warranty and service information.

Culligan International Company 9399 W. Higgins Rd., Suite 1100

Rosemont, IL 60018 USA 1-800-CULLIGAN or 1-847-430-2800 www.culligan.com

©2007 Culligan International Company 01017642C

With Culligan You Get More

Than a Quality Product

You Get Your Water Expert, The Culligan Man

We’re here to provide you with fast, dependable service, making sure any problems you have are taken care of. The Culligan Man has been around for over seventy years, delivering dependable service all along. That’s why people say “Hey, Culligan Man!®” Because we’re the water experts.

And that’s who you want taking care of your water.

The Culligan Promise

At Culligan, we understand that a water quality improvement system is an investment in your family’s well-being. That’s why our 1,350 independently operated dealers worldwide don’t just sell products;

they sell water quality you can count on. We stand behind our products with written limited warranties and our unequaled Culligan service. No matter where you live, you can depend on Culligan expertise to work for you — today and tomorrow.

Materials & Description: Medallist Filter Series Owners Guide 01017642

Size: 11” x 17”

Color: Black, 2 Sided

Stock: 20# White

Other: Collate, Bookletmaker (Fold to 8 1/2 x 11”)

Saddle Stitch with 2 Staples

Standard 3 Hole Drill

This page contains materials and DCO information.

IT DOES NOT PRINT AS PART OF THE DOCUMENT!

Let Change By Aprvd DCO Date

A New Art Created LR JS 7473 07/30/04

B1 Update WQA-move to 8780 LR JS 8671 08/22/05

B2 Update Art LR JS 8780 11/21/06

C1 Regl. Update LR JS 10083 06/04/07