Pages from UST_AST BoDR_60 Percent_Final_Compiled.pdf

A AMPERES

AFF ABOVE FINISH FLOOR

AFG ABOVE FINISH GRADE

AHJ AUTHORITY HAVING JURISDICTION

AIC AMPERE INTERRUPTING CAPACITY

AL ALUMINUM

APPROX APPROXIMATELY

ATS AUTOMATIC TRANSFER SWITCH

AWG AMERICAN WIRE GAUGE

AXL ACROSS THE LINE STARTER

BLDG BUILDING

BOD BASIS OF DESIGN

C CONDUIT

CB CIRCUIT BREAKER

CHG&E CENTRAL HUDSON GAS & ELECTRIC

CKT CIRCUIT

CL CENTERLINE

CLF CURRENT LIMITING FUSE

CONT CONTRACT

CPT CONTROL POWER TRANSFORMER

CT CURRENT TRANSFORMER

CU COPPER

DB DUCT BANK

DISC DISCONNECT

DP DIFFERENTIAL PRESSURE SWITCH

DR DIRECTOR'S REPRESENTATIVE

DWG DRAWING

EC ELECTRICAL CONTRACTOR

ECS EQUIPMENT CONNECTION SCHEDULE

EM EMERGENCY

EMT ELECTRICAL METALLIC TUBING

ETR EXISTING TO REMAIN

FLA FULL LOAD AMPERES

FMC FLEXIBLE METAL CONDUIT

FOMC FIBER OPTIC MEDIA CONVERTER

FT FEET

FURN FURNISHED

FVR FULL VOLTAGE REVERSING STARTER

FVNR FULL VOLTAGE NON-REVERSING STARTER

GC GENERAL CONTRACTOR

GF GROUND FAULT

GFCI,GFI GROUND-FAULT CIRCUIT INTERRUPTER

GND,G GROUND OR GROUNDING

HH HANDHOLE

HMI HUMAN MACHINE INTERFACE

HOA HAND, OFF, AUTOMATIC SWITCH

HP HORSEPOWER

HT HEAT TRACE

HVAC HEATING, VENTILATING, & AIR CONDITIONING

IBC INTERNATIONAL BUILDING CODE

IFC INTERNATIONAL FIRE CODE

INST INSTALLED

JB JUNCTION BOX

KCMIL THOUSAND CIRCULAR MILS

KVA KILOVOLT AMPERES

KW KILOWATTS

LCS LOCAL CONTROL STATION

LPS LIGHTNING PROTECTION SYSTEM

LTG LIGHTING

LFMC LIQUID TIGHT FLEXIBLE METAL CONDUIT

MC METAL CLAD CABLE

MCC MOTOR CONTROL CENTER

MCB MAIN CIRCUIT BREAKER

MCP MOTOR CIRCUIT PROTECTOR

MDP MAIN DISTRIBUTION PANELBOARD

MFG MANUFACTURER

MIN MINIMUM

MLO MAIN LUGS ONLY

MS MOTOR STARTER

MTS MANUAL TRANSFER SWITCH

MWTP MOTOR WINDING THERMAL PROTECTOR

NC NORMALLY CLOSED

NEC NATIONAL ELECTRICAL CODE

NEMA NAT'L ELECTRICAL MANUFACTURER'S ASSOC.

NESC NATIONAL ELECTRICAL SAFETY CODE

NF NON FUSED

NIC NOT IN CONTRACT

NP NAME PLATE

NTS NOT TO SCALE

NVR NETWORK VIDEO RECORDER

OC ON CENTER

OEM ORIGINAL EQUIPMENT MANUFACTURER

OHE OVERHEAD ELECTRIC

OIU OPERATOR INTERFACE UNIT

OL OVERLOADS

P POLE

PH PHASE

POE ETHERNET SWITCH W/ POWER OVER ETHERNET

PS PUMP STATION

PVC POLYVINYL CHLORIDE

QTY QUANTITY

REQ'D REQUIRED

RGS RIGID GALVANIZED STEEL

RMC RIGID METAL CONDUIT

RUGE REINFORCED UNDERGROUND ELECTRIC

SLD SINGLE LINE DIAGRAM

SP SPARE

STP SHIELDED TWISTED PAIR

TBR TO BE REMOVED

TSTAT THERMOSTAT

TYP TYPICAL

TVSS TRANSIENT VOLTAGE SURGE SUPPRESSION

UGE UNDERGROUND ELECTRIC

UOI UNLESS OTHERWISE INDICATED

UON UNLESS OTHERWISE NOTED

V VOLT

VFD VARIABLE FREQUENCY DRIVE

VFI VACUUM FAULT INTERRUPTER

W WIRE

WP WEATHER PROOF RATED DEVICE

XFMR TRANSFORMER

∆ DELTA

Υ WYE

ɸ PHASE

L2PA-2

LP2A-1,3,5

HOMERUN TO PANEL "LP2A", CIRCUITS #1,3,5 (VIA

20A-3P C/B). PROVIDE INSULATED GROUND

CONDUCTOR IN ACCORDANCE WITH

SPECIFICATIONS. NUMBER OF CIRCUITS INDICATED

BY QUANTITY OF ARROW HEADS

HOMERUN TO PANEL "L2PA" VIA 20A/1P CKT BKR.

SEE BELOW PARAGRAPH 'HASH MARKS' FOR

CONDUCTOR SIZING:

HASH MARKS INDICATE QUANTITY OF #12 AWG

COPPER CONDUCTORS IN CONDUIT. WHEN NO

HASH MARKS ARE INDICATED, CONDUIT SHALL

CONTAIN (2) #12 WIRES AND #12 GROUND WIRE.

ASSUME 1/2" DIAMETER CONDUIT, UNLESS NOTED

OTHERWISE NOTED

EXAMPLE SHOWN AT LEFT INDICATES 2 HOT

(SHORT LINES), 2 NEUTRAL (LONG LINES), AND 1

GROUND WIRES (LONG LINE WITH TAIL).

AMMETER

DRAWING NOTATION

CIRCUITING

DB-XX

**NOTE**

CONDUCTORS REQUIRED FOR LUMINAIRE SWITCHING ARE NOT

ACCOUNTED FOR ON THE PLANS USING HASH MARKS. CONTRACTOR

SHALL INCLUDE ANY NECESSARY CONDUCTORS REQUIRED FOR

SWITCHING IN BID. SWITCHING DESIGNATIONS (LOWER CASE LETTERS)

ARE SHOWN TO ILLUSTRATE SWITCHING INTENT.

CIRCUIT ROUTING SHOWN ON DRAWINGS SHALL BE CONSIDERED

DIAGRAMMATIC ONLY. CONTRACTOR SHALL PROVIDE NECESSARY

OFFSETS AND ROUTE FEEDERS AFTER HAVING CONSIDERED ALL FIELD

OBSTACLES

TEXT ADJACENT TO EQUIPMENT IS SOMETIMES ADDED FOR EXTRA

CLARIFICATION ON REMOVAL/EXISTING TO REMAIN ITEMS. REFER

TO LIST BELOW FOR DEFINITIONS.

TBR EXISTING EQUIPMENT TO BE REMOVED BY THIS

CONTRACT.

ETR EXISTING EQUIPMENT TO REMAIN.

ERE EXISTING EQUIPMENT TO BE REMOVED AND

RELOCATED AS SHOWN BY THIS CONTRACT.

ETN EXISTING EQUIPMENT TO BE REMOVED AND

REPLACED BY THIS CONTRACT.

UGE UNDERGROUND ELECTRIC (SAND FILL)

UNDERGROUND ELECTRIC (REINFORCED CONCRETE)

OHE OVERHEAD ELECTRIC

HT HEAT TRACE

HEAVY & DOTTED AND/OR HATCHED INDICATES

EXISTING EQUIPMENT TO BE REMOVED BY THIS

CONTRACT.

SOLID & LIGHT INDICATES EXISTING EQUIPMENT TO

REMAIN.

HEAVY & SOLID INDICATES EQUIPMENT TO BE

PROVIDED BY THIS CONTRACT.

DESIGNATION FOR UNDERGROUND ELECTRICAL DUCT

BANK

AMPS

G E N

E R

A L

A

B B

R E V

I A

T I O

N S

G E N

E R

A L

N

O T

A T

I O

N C

I R

C U

I T

I N

G

L E G

E N

D

HP

EXISTING ELECTRICAL CONNECTION.

('HP' DENOTES HORSEPOWER.)

THRU WALL WATERTIGHT

PENETRATION

VOLTMETER

VOLTS

400AF

300AT

200A

**AF

**AT

SURFACE MTD BRANCH CIRCUIT PANELBOARD.

HEAVY DUTY NON-FUSED DISCONNECT SWITCH.

"AF" - INDICATES FRAME SIZE

"P" - INDICATES # OF POLESAF/P

AF/AT/P

HEAVY DUTY FUSED DISCONNECT SWITCH.

"AF" - INDICATES FRAME SIZE

"AT" - INDICATES FUSE TRIP SIZE

"P" - INDICATES # OF POLES

JUNCTION AND/OR PULL BOX

ELECTRICAL CONNECTION AS DEFINED IN

EQUIPMENT CONNECTION SCHEDULE.

SINGLE LINE DIAGRAM FLOOR PLAN

PANELBOARD WITH

MAIN CIRCUIT BREAKER

PANELBOARD WITH

MAIN LUGS ONLY

RECESSED MTD BRANCH CIRCUIT PANELBOARD.

EMERGENCY

GENERATOR

M

METER

ATS / MTS

POWER TRANSFORMER

POTENTIAL TRANSFORMER

CURRENT TRANSFORMER

FUSE

MOLDED CASE CIRCUIT BREAKER

"AF" INDICATES AMPERE FRAME SIZE

"AT" INDICATES AMPERE TRIP SETTINGS

FUSED DISCONNECT

"400AF" INDICATES AMPERE SWITCH SIZE

"300AT" INDICATES AMPERE FUSE SIZE

DISCONNECT SWITCH (NON-FUSED)

"200A" INDICATES AMPERE SWITCH SIZE

SYSTEM GROUND OR EQUIPMENT GROUND

P O

W E R

Q

U I P

M E N

T

CONTACTOR

(NORMALLY OPEN)

CONTACTOR

(NORMALLY CLOSED)

LOCAL PUSH BUTTON

CONTROL STATION

E

FLEX CONNECTION

(E DENOTES EXPLOSION PROOF)

CONDUIT

SEALING FITTING

CONDUIT

UNION

CONDUIT

BUSHING

CONTROL

DEVICE/INSTRUMENT

UTILITY POLE

VARIABLE FREQUENCY

DRIVE (VFD)

PT

CT

ACROSS-THE-LINE

STARTER

(AXL)

SURGE SUPPRESSION DEVICESPD

JB

ALARM/ INDICATION LIGHT

POWER METER

KWHD

RUGE

SURVEILLANCE CAMERA

SURVEILLANCE CAMERA

INPUT LINE REACTOR

KDR

CARBON MONOXIDE DETECTORCO

SYMBOLS AND ABBREVIATIONS

1. THIS SHEET CONTAINS SYMBOLS AND ABBREVIATIONS TYPICALLY SHOWN ON ELECTRICAL DRAWINGS AND SCHEMATICS. THIS CONTRACT

DRAWING SET MAY NOT CONTAIN ALL SYMBOLS AND ABBREVIATIONS SHOWN ON THIS SHEET.

SAFEGUARDS DURING CONSTRUCTION

1. ALL CONSTRUCTION WORK COVERED IN THE UNIFORM CODE, INCLUDING ANY REMOVAL, SHALL COMPLY WITH THE REQUIREMENTS OF

CHAPTER 33 OF THE 2020 FCNYS AND CHAPTER 33 OF THE 2020 BCNYS.

PERMITS AND INSPECTIONS

1. OBTAIN ALL REQUIRED PERMITS AND ARRANGE FOR ALL REQUIRED INSPECTIONS IN ACCORDANCE WITH STATE AND LOCAL GOVERNING

AUTHORITIES.

2. COMPLETE WORK IN ACCORDANCE WITH THE 2017 NEC, AND STATE AND LOCAL GOVERNING REGULATIONS.

3. PERFORM WORK AS REQUIRED BY CODES, REGULATIONS, LAWS OF LOCAL, STATE AND FEDERAL GOVERNMENTS, AND OTHER AUTHORITIES

WITH LAWFUL JURISDICTION. ALL MATERIAL AND EQUIPMENT SHALL BE UL LISTED.

SCOPE

1. UNLESS OTHERWISE INDICATED, PROVIDE A COMPLETE AND OPERATIONAL ELECTRICAL SYSTEM INCLUDING ALL NECESSARY MATERIAL, LABOR, AND EQUIPMENT.

2. ALL DISCONNECTS REQUIRED BY CODE MAY NOT BE SHOWN. CONTRACTOR SHALL PROVIDE ALL NECESSARY DISCONNECTS PER 2017

NEC.

3. ALL EQUIPMENT AND MATERIAL SHALL BE LABELED AND LISTED, AND INSTALLED IN ACCORDANCE WITH THEIR LISTING.

4. PROVIDE ELECTRICAL CONNECTION FOR EVERY FIXTURE, OR ITEM OF EQUIPMENT REQUIRING SAME, WHICH IS SHOWN OR LISTED ON ANY

CONTRACT DRAWING

5. CONTRACTOR SHALL PROVIDE NECESSARY SUPPORT FRAMING, STIFFENERS, BRACING, AND HANGERS WHETHER SHOWN OR NOT TO

ENSURE A COMPLETE AND DURABLE SYSTEM. SUPPORT FRAMING CONNECTIONS SHALL BE WELDED UNLESS SPECIFICALLY SHOWN

OTHERWISE. ACTUAL SUPPORTS MAY VARY FROM THOSE SHOWN IN DETAILS TO ACCOMMODATE EXISTING FIELD CONDITIONS.

6. THE WORK INCLUDED IN THIS CONTRACT ENCOMPASSES THE DRAWINGS AND SPECIFICATIONS. WORK INCLUDED ON THE DRAWINGS

ONLY, OR IN THE SPECIFICATIONS ONLY, SHALL BE INCORPORATED AS IF INCLUDED IN BOTH. ALL SYSTEMS SHOWN ARE INTENDED TO BE

COMPLETE AND FULLY FUNCTIONING. THE CONTRACTOR SHALL PROVIDE SUCH COMPONENTS AS NECESSARY FOR A FULLY FUNCTIONING

SYSTEM.

7. ALL EQUIPMENT SHALL BE INSTALLED IN A NEAT AND WORKMANLIKE MANNER, RECTILINEAR TO BUILDING STRUCTURE.

8. FIELD VERIFY ALL SITE CONDITIONS AND DIMENSIONS PRIOR TO COMMENCEMENT OF ANY WORK OR SHOP FABRICATION. REPORT ANY

DISCREPANCIES TO THE DIRECTOR'S REPRESENTATIVE IN WRITING, PRIOR TO COMMENCEMENT OF ANY WORK.

COORDINATION OF WORK

1. COORDINATE AND VERIFY THAT WORKING AND DEDICATED EQUIPMENT SPACE REQUIREMENTS ARE MET PER NEC.

2. FIELD LOCATE ALL CORE DRILL LOCATIONS.

3. BEFORE CUTTING OR DRILLING INTO BUILDING ELEMENTS INSPECT AND LAYOUT WORK TO AVOID DAMAGING STRUCTURAL ELEMENTS

AND BUILDING UTILITIES.

4. BEFORE SELECTING MATERIAL/EQUIPMENT AND PROCEEDING WITH WORK, INSPECT AREAS WHERE MATERIAL AND EQUIPMENT ARE TO BE

INSTALLED TO INSURE SUITABILITY, AND CHECK NEEDED SPACE FOR PLACEMENT, CLEARANCES AND INTERCONNECTIONS.

5. POSSIBLE SYSTEM SHUT-DOWNS AND WORK AREAS CLOSURES MUST BE COORDINATED WELL IN ADVANCE WITH THE CONTRACTOR

OFFICER'S REPRESENTATIVE.

6. VERIFY RECEPTACLE, SWITCH, & COVER PLATE COLORS WITH THE CONTRACTOR OFFICER'S REPRESENTATIVE.

7. TURN OVER TO THE CONTRACTOR OFFICER'S REPRESENTATIVE ALL MANUFACTURER'S WARRANTIES FOR EQUIPMENT AND MATERIALS

PROVIDED.

8. COORDINATE ANY REQUIRED CONTRACTOR STAGING AREA WITH THE CONTRACTOR OFFICER'S REPRESENTATIVE.

DEFINITIONS

1. THE DEFINITION OF ELECTRICAL TERMS USED SHALL BE AS DEFINED IN THE 2017 EDITION OF THE NATIONAL ELECTRICAL CODE (NEC) AS

REFERENCED IN THE BUILDING CODE OF NEW YORK STATE.

2. THE TERM "INDICATED" SHALL MEAN "AS SHOWN ON CONTRACT DOCUMENTS (SPECIFICATIONS, DRAWINGS, AND RELATED

ATTACHMENTS)".

3. THE TERM "PROVIDE" SHALL MEAN "TO FURNISH, INSTALL, AND CONNECT COMPLETELY".

4. THE TERM "SIZE" SHALL MEAN ONE OR MORE OF THE FOLLOWING: "LENGTH, CURRENT AND VOLTAGE RATING, NUMBER OF POLES, NEMA

SIZE, AND OTHER SIMILAR ELECTRICAL CHARACTERISTICS".

PLANS

1. ELECTRICAL PLANS, DETAILS, AND ONE LINE DIAGRAMS SHOW THE GENERAL LOCATION AND ARRANGEMENT OF THE ELECTRICAL SYSTEM.

THEY ARE DIAGRAMMATIC AND DO NOT SHOW ALL CONDUIT BODIES, CONNECTORS, BENDS, FITTINGS, HANGERS, AND ADDITIONAL PULL

BOXES WHICH THE CONTRACTOR MUST PROVIDE TO COMPLETE THE ELECTRICAL SYSTEM.

2. ELECTRICAL PLANS AND DETAILS DO NOT SHOW ALL INTERFERENCES AND CONDITIONS, VISIBLE AND/OR HIDDEN, THAT MAY EXIST.

CONTRACTOR MUST INSPECT AND SURVEY THE SPACE BEFORE PERFORMING THE WORK.

3. THESE DRAWINGS ARE SCHEMATIC IN NATURE AND REPRESENT A COMPLETED PROJECT. MINOR MODIFICATIONS OF WORK SHALL BE

PROVIDED BY THE CONTRACTOR TO COMPLY WITH PROJECT REQUIREMENTS, LOCATIONS OF DEVICES AND EQUIPMENT SHOW A GENERAL

ARRANGEMENT AND INTENDED FUNCTION. ALL COMPONENTS SHOWN ON THE RISER DIAGRAMS, BUT NOT ON THE PLAN OR VICE VERSA, SHALL BE INCLUDED AS IF SHOWN ON BOTH. EXACT LOCATION OF MECHANICAL EQUIPMENT THAT REQUIRE ELECTRICAL CONNECTIONS

ARE SHOWN ON THE MECHANICAL DRAWINGS. BEFORE INSTALLATION OF WORK, CHECK FOR SWINGS AND ALL REQUIRED CLEARANCES, TO AVOID INTERFERENCE WITH OTHER TRADES. COORDINATE WITH ALL CONTRACT DOCUMENTS, SHOP DRAWINGS AND EQUIPMENT

DRAWINGS. THE CONTRACTOR IS RESPONSIBLE FOR OBTAINING ALL REQUIRED CONTRACT DRAWINGS.

METHODS

1. CORE DRILL ALL THRU WALL & THRU FLOOR PENETRATIONS. ALL THRU FLOOR CONDUIT PENETRATIONS TO BE PROPERLY SEALED TO

ELIMINATE POTENTIAL FOR WATER TO ENTER CONDUIT SYSTEM OR PASS THRU FLOOR PENETRATION.

2. ALL EXTERIOR CONDUITS TO HAVE DUCT SEAL INSTALLED AT ALL ENDS, BOXES, WEATHERHEADS, PENETRATIONS TO INTERIOR SPACES, ETC.

3. DUCT BANKS SHALL NOT BE ROUTED DIRECTLY ABOVE OR BELOW EXISTING/NEW UTILITIES EXCEPT WHEN CROSSING. WHERE CROSSING

EXISTING OR NEW UTILITY DUCT BANKS SHALL CROSS AT 90 DEGREE ANGLES.

4. ALL CONDUIT SYSTEMS EXPOSED TO TEMPERATURE DIFFERENTIALS, IN POTENTIAL CONDENSING ATMOSPHERES, EXTERIOR INSTALLED, OR

INSTALLED UNDERGROUND SHALL HAVE PROVISIONS FOR DRAINING WATER OUT OF CONDUIT SYSTEMS.

5. WHERE WIRE SIZE IS NOT NOTED ON DRAWINGS, CONTRACTOR SHALL SIZE ACCORDING TO THE NEC AND SHALL ADHERE TO THE

FOLLOWING CRITERIA:

· EQUIPMENT CIRCUITS AND FEEDERS LESS THAN OR EQUAL TO 100A SHALL BE SIZED USING THE 60°C COPPER AMPACITY COLUMN (NEC

T310.16).

· EQUIPMENT CIRCUITS AND FEEDERS GREATER THAN 100A SHALL BE SIZED USING THE 75°C COPPER AMPACITY COLUMN (NEC T310.16).

MINIMUM WIRE SIZE SHALL BE #12 THHN/THWN.

· ALUMINUM SHALL NOT BE USED. CONDUCTORS SHALL BE SOLID UP THROUGH #10.

6. FASTENERS ON THE UNDERSIDE OF PRECAST/PRESTRESSED CONCRETE MEMBERS (PLANKS OR DOUBLE TEES) WHICH SERVE FOR DIRECT

ATTACHMENT FOR HANGERS OF CONDUIT, ELECTRICAL EQUIPMENT, ETC., MAY NOT BE DRILLED-IN OR SHOT-IN IN THE VACINITY OF THE

PRESTRESSING TENDONS. THIS MEANS THAT THE FASTENERS AT THE CONCRETE PLANKS CAN BE PLACED ONLY AT THE JOINT BETWEEN

UNITS (UNITS ARE APPROXIMATELY 40" WIDE). ANY INTERMEDIATE SUPPORTS NEEDED TO ACCOMPLISH THIS SHALL BE PROVIDED BY THE

CONTRACTOR. AT DOUBLE TEES, ATTACHMENT TO THE FLANGES IS ALLOWED. HOWEVER, BECAUSE OF THEIR THIN CROSS SECTIONS, HEAVY LOADS MUST BE CARRIED BY THROUGH-BOLTS WHICH MUST BE INSTALLED BEFORE THE ROOFING IS APPLIED.

UNDERGROUND UTILITIES

1. UNDERGROUND UTILITY LOCATIONS ARE NOT GUARANTEED, NOR IS THERE ANY GUARANTEE THAT ALL EXISTING UTILITIES WHETHER

FUNCTIONAL OR ABANDONED WITHIN THE PROJECT AREA ARE SHOWN ON THESE DRAWINGS.

2. THE CONTRACTOR SHALL DETERMINE THE EXACT LOCATION OF ALL UNDERGROUND UTILITIES BEFORE BEGINNING WORK & SHALL BE

RESPONSIBLE FOR ALL DAMAGE RESULTING FROM HIS/HER WORK.

3. THE CONTRACTOR SHALL NOTIFY "DIG SAFELY NEW YORK" 1-800-962-7962 PRIOR TO ANY EXCAVATION.

4. NO ATTEMPT WAS MADE TO LOCATE SUBSURFACE STRUCTURES, ABOVEGROUND STRUCTURES AND/OR UTILITIES BELIEVED TO EXIST IN

THE WORKING AREA. IT SHALL BE THE CONTRACTOR'S RESPONSIBILITY TO LOCATE EXISTING UTILITIES NEEDED TO COMPLETE THE WORK

AND IT SHALL BE HIS RESPONSIBILITY TO PROCEED WITH GREAT CARE IN EXECUTING ANY WORK. CONTRACTOR SHALL COMPLY WITH THE

STATE OF NEW YORK DEPARTMENT OF PUBLIC SERVICE, 16NYCRR PART 753.

5. THE DIRECTOR'S REPRESENTATIVE SHALL BE NOTIFIED IN WRITING OF ANY CONDITIONS THAT VARY FROM THOSE SHOWN ON THE PLANS.

THE CONTRACTOR'S WORK SHALL NOT VARY FROM THE PLANS WITHOUT THE EXPRESSED APPROVAL OF THE DIRECTOR'S REPRESENTATIVE

AND DIRECTOR'S REPRESENTATIVE.

6. CONTRACTOR SHALL PROTECT ALL EXISTING STORM WATER DRAINAGE FACILITIES, INCLUDING PIPES, DRAINAGE STRUCTURES, SWALES, DITCHES, ETC. CONTRACTOR SHALL REPLACE AND RESTORE ANY AND ALL OF THESE FACILITIES, AFFECTED BY CONSTRUCTION ACTIVITIES, AT NO ADDITIONAL COST TO THE DIRECTOR'S REPRESENTATIVE.

7. CONTRACTOR SHALL BE RESPONSIBLE FOR PROTECTING EXISTING UTILITIES DURING OPERATIONS.

8. THE CONTRACTOR SHALL BE RESPONSIBLE FOR RESTORING ANY SURVEY OR RIGHT-OF-WAY MONUMENTS DISTURBED DURING

CONSTRUCTION. THE CONTRACTOR SHALL EMPLOY A LICENSED LAND SURVEYOR TO RESTORE ALL DISTURBED MONUMENTS TO THEIR

ORIGINAL LOCATION.

9. RESTORE ALL SURFACES TO AS GOOD OR BETTER CONDITION THAN BEFORE CONSTRUCTION AS SOON AS POSSIBLE FOLLOWING

COMPLETION OF WORK IN ANY AREA.

10. THE CONTRACTOR SHALL BECOME FAMILIAR WITH SITE CONDITIONS AND SHALL INCLUDE PROVISIONS TO AVOID CONFLICTS WITH

AND/OR RESTORE SITE FEATURES IN THE BID.

11. ALL SUITABLE EXCAVATED MATERIAL SHALL BE REUSED ON SITE AND BE SUITABLY STABILIZED SO THAT IT CANNOT REASONABLY RE-ENTER

ANY BODY OF WATER.

12. ALL EXCAVATION SHALL BE CONDUCTED IN ACCORDANCE WITH OSHA STANDARDS, LOCAL REGULATIONS, STATE REGULATIONS, AND

FEDERAL REGULATIONS.

G E N

E R

A L

N

O T

E S

RECEPTACLES

TEXT ADJACENT TO RECEPTACLES INDICATES CONFIGURATION OR

ACCESSORIES. REFER TO LIST BELOW FOR DEFINITIONS.

# INDICATES PANELBOARD CIRCUIT TO WHICH RECEPTACLE SHALL BE

CIRCUITED. REFER TO HOMERUN FOR PANELBOARD DESIGNATION.

WP EXTERIOR RECEPTACLES SUBJECT TO DAMP ENVIRONMENTS SHALL HAVE

WEATHER-PROOF-IN-USE BUBBLE COVER WITH PADLOCK CAPABILITY.

WEATHER-PROOF RECEPTACLES ARE TO HAVE INTEGRAL GFI

PROTECTION (SEE BELOW)

GFI RECEPTACLE EQUIPPED WITH INTEGRAL GROUND FAULT CIRCUIT

INTERRUPTER

XP EXPLOSION PROOF. RATED FOR CLASS I DIVISION I INSTALLATION.

125 VOLT, 2 POLE, 3 WIRE, 20 AMP., HEAVY DUTY DUPLEX

RECEPTACLE, MOUNTING HEIGHT 18" AFF (UON).

125 VOLT, 2 POLE, 3 WIRE, 20 AMP., HEAVY DUTY DUPLEX

RECEPTACLE MOUNTED ABOVE COUNTER (UON).

125 VOLT, 2 POLE, 3 WIRE, 20 AMP., HEAVY DUTY DUPLEX

RECEPTACLE, STANCHION-MOUNTED. PROVIDE NECESSARY

UNISTRUT/MOUNTING HARDWARE @ 24" A.F.G. (UON)

TEXT ADJACENT TO SWITCH INDICATES SPECIAL CONFIGURATION

OR ACCESSORIES. REFER TO LIST BELOW FOR DEFINITIONS.

a,b LOWER CASE LETTER INDICATES SWITCH DESIGNATION.

3,4 INDICATES A 3-WAY OR 4-WAY SWITCH.

WP EXTERIOR SWITCHES SUBJECT TO DAMP ENVIRONMENTS

SHALL HAVE WEATHER-PROOF-IN-USE BUBLE COVER WITH

PADLOCK CAPABILITY.

M MOTOR RATED SNAP SWITCH WITH OVERLOADS.

CONTRACTOR SHALL SIZE SWITCH AND OVERLOADS BASED

ON ACTUAL NAMEPLATE DATA OF EQUIPMENT

SUPPLIED/PURCHASED.

D DIMMING SWITCH (SLIDER TYPE). SWITCH SHALL BE

COMPATIBLE WITH INSTALLED FIXTURES. PROVIDE WITH

MANUAL "ON/OFF" CONTROL OF LIGHTING FIXTURES

CONTROLLED.

XP EXPLOSION PROOF. RATED FOR CLASS I DIVISION I

INSTALLATION.

1. FACEPLATE COLOR - STAINLESS STEEL, UON.

2. DEVICE COLOR - GRAY, UON.

125V, 20A HEAVY DUTY SWITCH.

SWITCHES

1. FACEPLATE COLOR - STAINLESS STEEL, UON.

2. DEVICE COLOR - GRAY, UON.

W I R

I N

G

D

E V

I C

E S

S O

L I C

I T

A T

I O

N

N

O

D E

S I G

N E

D

B

Y

D E

S C

R I P

T I O

N

M A

R K

S I Z

E

S U

B M

I T

T E

D

B

Y

D A

T E

C O

N T

R A

C T

N

O

C H

E C

K E

D

B

Y

D R

A W

N

B

Y

I S

S U

E

D

A T

E

SHEET ID

G

2 3 4 5 6 7 8 9 10

F

E

D

C

B

A

U S

A

R M

Y

C

O R

P S

F

E

N G

I N

E E

R S

US Army Corps of Engineers

U S

E R

F

I L

E N

A M

E

P

J S

E

P

R O

J E

C T

S

W

A T

E R

V L

I E

T

A

S T

U

S T

A

C T

I V

E

D

R A

W I N

G S

M

P E

E

D

W G

A V

E

D

A T

E

M

L O

T

D

A T

E

A

M

N E

W

Y

O R

K

D

I S

T R

I C

T

F

E D

E R

A L

P

L A

Z A

N E

W

Y

O R

K

N

Y

R

K

A N

S I

D

U S

T A

D

S

I G

N

P

R O

J E

C T

60% DESIGN

OF 70

NEW YORK LAW, SECTION 7209.2.

THE ALTERING PERSON SHALL COMPLY WITH THE REQUIREMENTS OF

SURVEYOR, TO ALTER THIS DOCUMENT IN ANY WAY. IF ALTERED,

THE DIRECTION OF A LICENSED PROFESSIONAL ENGINEER OR LAND

SECTION 7209.2, FOR ANY PERSON, UNLESS HE IS ACTING UNDER

WARNING - IT IS A VIOLATION OF NEW YORK EDUCATION LAW,

D

E S

I G

N

S

U B

M I T

T A

L

N

N

S T

R U

C T

I O

N

W A

T E

R V

L I E

T

A

R S

E N

J

R

O B

I N

S O

N

B

W

A L L

D R

O F

F

D

S

A N

F O

R D

J

R

O B

I N

S O

N J A

N U

A R

Y

X X

X X

X X

W

D R

D

J A

O

G

I N

E E

R I N

G

M E

C H

A N

I C

A L

E

L E

C T

R I C

A L

P

L U

M B

I N

G

V

A N

D U

Z E

E

S

T

W

A T

E R

T O

P

T O

N E

E N

G C

O M

AutoCAD SHX Text C

AutoCAD SHX Text ENERGY CODE NOTE TO THE BEST OF THE ENGINEER'S KNOWLEDGE, BELIEF AND PROFESSIONAL JUDGEMENT, THESE PLANS AND/OR SPECIFICATIONS, ARE IN COMPLIANCE WITH THE 2020 ENERGY CONSERVATION CONSTRUCTION CODE OF NEW YORK STATE.

AutoCAD SHX Text BUILDING CODE NOTE TO THE BEST OF THE ENGINEER'S KNOWLEDGE, BELIEF AND PROFESSIONAL JUDGEMENT, THESE PLANS AND/OR SPECIFICATIONS, ARE IN COMPLIANCE WITH THE 2020 UNIFORM CODE.

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text E-01

AutoCAD SHX Text

ELECTRICAL LEGEND, ABBREVIATIONS, AND NOTES

U

G

E

R

U

G

E

R

U

G

E

BUILDING 123

(REFER TO E-05)

BUILDING 152

(REFER TO E-07)

BUILDING 145

(REFER TO E-06)

BUILDING 35

(REFER TO E-04)

BUILDING 15

(REFER TO E-03)

WVA-14

(T.B.R.)

WVA-28

ROLL-OFF FACILITY

(REFER TO E-09)

ROLL-OFF FACILITY

(REFER TO E-09)

GASOLINE FUELING FACILITY

(REFER TO E-08)

DIESEL FUELING FACILITY

(REFER TO E-08)

BUILDING 116

REFER TO ADJACENT

ENLARGED SITE PLAN

DB-01

BUILDING 135

(REFER TO E-10)

WVA-28

(T.B.R.)

GASOLINE FUELING FACILITY

(REFER TO E-08)

DIESEL FUELING FACILITY

(REFER TO E-08)

R

U

G

E

DB-02

DB-03

BUILDING 116

GENERAL DEMOLITION NOTES:

1. REFER TO E-01 FOR ELECTRICAL LEGENDS, ABBREVIATIONS, AND GENERAL PROJECT NOTES.

2. ITEMS INDICATED TO BE REMOVED:

2.1. REMOVE ALL CONDUCTORS AND EXPOSED CONDUIT BACK TO SOURCE (UOI).

2.2. REMOVE CIRCUIT WIRING AND CIRCUIT BREAKER FROM SOURCE PANEL (UOI).

2.3. REMOVE ALL ASSOCIATED CONTROL CONDUCTORS, CONDUITS, AND DEVICES (UOI).

2.4. REMOVE ASSOCIATED STARTERS, DISCONNECTS, CONTROL STATIONS, AND ALL ASSOCIATED CIRCUITRY (UOI).

2.5. REMOVE EQUIPMENT PADS & MOUNTING HARDWARE, BRACKETS, ACCESSORIES, ETC... (UOI).

2.6. REVISE PANELBOARD DIRECTORIES/NAME PLATES AS CHANGES OCCUR (UOI).

3. THESE REMOVAL DRAWINGS ARE SCHEMATIC IN NATURE AND ARE BASED ON CURSORY FIELD OBSERVATION AND EXISTING DRAWINGS. IT IS NOT THE INTENTION

OF THESE DRAWINGS TO INDICATE EVERY DEVICE/FIXTURE REQUIRING REMOVAL RATHER GENERAL SYSTEMS WHICH ARE TO BE REMOVED. COORDINATE REMOVAL

EFFORTS CLOSELY WITH CONTRACTOR OFFICER'S REPRESENTATIVE.

4. CIRCUITS NOT IN AREA OF WORK THAT ARE AFFECTED BY WORK SHALL BE OPERATIONAL DURING PROJECT. PROVIDE TEMPORARY CIRCUITS AS NECESSARY.

5. CIRCUIT, EQUIPMENT, AND DEVICE REMOVAL SHALL NOT AFFECT THE INTEGRITY OR FUNCTIONALITY OF CIRCUITS TO REMAIN. ALL CIRCUITS TO REMAIN SHALL BE

MAINTAINED. PROVIDE ALL NECESSARY CIRCUIT MODIFICATIONS AND EXTENSIONS.

6. WHERE REMOVALS LEAVE HOLES AND DAMAGED SURFACES EXPOSED IN THE FINISHED WORK, PATCH AND REPAIR THESE HOLES AND DAMAGED SURFACES TO

MATCH ADJACENT FINISHED SURFACES. WHERE WORK IS TO BE APPLIED TO EXISTING SURFACES, PERFORM REMOVALS, AND PATCHING IN A MANNER TO

PRODUCE SURFACES SUITABLE FOR RECEIVING WORK. COORDINATE ALL WORK WITH CONTRACTOR OFFICER'S REPRESENTATIVE.

7. NOT ALL ELECTRICAL EQUIPMENT/DEVICES ARE SHOWN FOR CLARITY. CONTRACTOR SHALL FIELD VERIFY ALL EXISTING CONDITIONS AND REPORT DISCREPANCIES

TO CONTRACTOR OFFICER'S REPRESENTATIVE PRIOR TO COMMENCEMENT OF REMOVAL.

8. WHERE REMOVAL OF CONDUIT SYSTEM IS NOT FEASIBLE, REMOVE ALL CONDUCTORS FROM CONDUIT SYSTEM, CUT FLUSH, CAP CONDUIT SYSTEM, AND

ABANDON IN PLACE. FEASIBLE IS DEFINED AS BEING LOCATED WITHIN A CONCRETE DUCT BANK OR CONCRETE SLAB. ALL OTHER INSTANCES TO HAVE THE

CONDUIT & CIRCUITRY TO BE REMOVED IN THERE ENTIRETY. FIELD VERIFY AND COORDINATE FINAL REQUIREMENTS WITH THE CONTRACTOR OFFICER'S

REPRESENTATIVE, TYPICAL.

9. NOT ALL EXISTING UNDERGROUND UTILITIES SHOWN FOR CLARITY. REFER TO SITE PLANS AND GENERAL NOTES ON SHEET E-01 FOR ADDITIONAL SITE

INFORMATION. FIELD VERIFY AS REQUIRED.

10. ALL EXISTING UNDERGROUND/SUB-SURFACE ELECTRICAL DUCT BANKS, FEEDERS, AND BRANCH CIRCUITS NOT SHOWN FOR CLARITY. REFER TO ELECTRICAL SINGLE

LINE DIAGRAM - DEMOLITION FOR REMOVAL INFORMATION.

11. CONTRACTOR TO COORDINATE SEQUENCE OF REMOVALS WITH THE CONTRACTOR OFFICER'S REPRESENTATIVE. REFER TO SPECIFICATIONS AND DEMOLITION

SINGLE LINE DIAGRAM FOR ADDITIONAL INFO.

A. ALL WORK MUST BE PERFORMED IN SUCH A MANNER SO AS TO MAINTAIN FACILITY SECURITY AT ALL TIMES IN STRICT

ACCORDANCE WITH THE PROJECT MANUAL.

B. ALL WORK NEAR THE PERIMETER SECURITY FENCES MUST BE PERFORMED IN SUCH A MANNER SO AS TO MAINTAIN PERIMETER

SECURITY AT ALL TIMES IN STRICT ACCORDANCE WITH THE PROJECT MANUAL.

C. THE FACILITY IS PROTECTED BY PERIMETER FENCES, PERIMETER FENCE LIGHTING SYSTEM, PERIMETER ALARM SYSTEMS, AND

PERIMETER SURVEILLANCE CCTV SYSTEM, WHICH ARE INTEGRATED TOGETHER TO WORK AS A SINGLE PERIMETER SECURITY

SYSTEM. THESE SYSTEMS SHALL BE FULLY OPPERATIONAL AT ALL TIMES DURING THE WORK OF THIS CONTRACT. THE WORK

REQUIRED BY THIS CONTRACT NEAR THESE SYSTEMS, SHALL BE PERFORMED IN SUCH A MANNER SO AS TO PREVENT ANY DOWN

TIME (INTERRUPTIONS) TO ANY OF THESE SYSTEMS.

D. THE EXACT LOCATIONS OF EXISTING UNDERGROUND UTILITIES AND PERIMETER SECURITY LINES ARE UNKNOWN AND SHOWN

APPROXIMATE ONLY. BEFORE ANY WORK IS STARTED NEAR THE PERIMETER FENCES, DETERMINE EXACT LOCATION OF ALL

UNDERGROUND UTILITIES AND PERIMETER SECURITY SYSTEM LINES (WHETHER SHOWN ON DRAWINGS OR NOT) BY USE OF AN

UNDERGROUND UTILITY LOCATOR SERVICE. MARK AND PROTECT ALL UNDERGROUND UTILITIES AND PERIMETER SECURITY

SYSTEM LINES. CONTRACTOR SHALL BE HELD RESPONSIBLE FOR ANY DAMAGE TO ANY UNDERGROUND UTILITIES AND PERIMETER

SECURITY SYSTEM LINES.

E. EXTREME CAUTION SHALL BE USED WHEN WORKING NEAR THE PERIMETER SECURITY SYSTEMS AND THEIR ASSOCIATED CIRCUITS.

THE CONTRACTOR SHALL BE HELD RESPONSIBLE FOR ANY DAMAGE TO THESE SYSTEMS AND/OR LOSSES DUE TO DAMAGE TO

THESE SYSTEMS, INCLUDING THE COST TO REPAIR THE DAMAGE AND ANY COST INCURRED BY THE CONTRACTOR OFFICER'S

REPRESENTATIVE FOR ADDITIONAL SECURITY STAFF TO PROTECT THE PERIMETER OF THE FACILITY DUE TO ANY OUTAGES OF THE

SECURITY SYSTEMS.

S O

L I C

I T

A T

I O

N

N

O

D E

S I G

N E

D

B

Y

D E

S C

R I P

T I O

N

M A

R K

S I Z

E

S U

B M

I T

T E

D

B

Y

D A

T E

C O

N T

R A

C H

E C

K E

D

B

Y

D R

A W

N

B

Y

I S

S U

E

D

A T

E

SHEET ID

G

2 3 4 5 6 7 8 9 10

F

E

D

C

B

A

U S

A

R M

Y

C

O R

E

N G

I N

E E

R S

US Army Corps of Engineers

U S

E R

F

I L

E N

A M

E

P

J S

E

P

R O

J E

C T

S

W

A T

E R

V L

I E

T

A

S T

U

S T

A

C T

I V

E

D

R A

W I N

G S

M

P E

E

D

G

V

E

D

A T

E

M

O

T

D

A T

E

A

M

N E

W

Y

O R

K

D

I S

T R

I C

T

F

E D

E R

A L

P

L A

Z A

N E

W

Y

O R

K

N

R

K

A N

S I

D

U S

T A

S

I G

N

P

R O

J E

C T

60% DESIGN

OF 70

NEW YORK LAW, SECTION 7209.2.

THE ALTERING PERSON SHALL COMPLY WITH THE REQUIREMENTS OF

SURVEYOR, TO ALTER THIS DOCUMENT IN ANY WAY. IF ALTERED,

THE DIRECTION OF A LICENSED PROFESSIONAL ENGINEER OR LAND

SECTION 7209.2, FOR ANY PERSON, UNLESS HE IS ACTING UNDER

WARNING - IT IS A VIOLATION OF NEW YORK EDUCATION LAW,

D

E S

I G

N

S

U B

M I T

T A

L

N

N

S T

R U

C T

I O

N

W A

T E

R V

L I E

T

A

R S

E N

R

O B

I N

S O

N

B

W

A L L

D R

O F

F

D

S

A N

F O

R D

J

R

O B

I N

S O

N J A

N U

A R

Y

X X

X X

X X

W

D

R

D

J A

O

G

I N

E E

R I N

G

M E

C H

A N

I C

A L

E

L E

C T

R I C

A L

P

L U

M B

I N

G

V

A N

D U

Z E

E

S

T

W

A T

E R

T O

P

T O

N E

E N

G C

O M

SHEET KEY NOTES:

CONTRACTOR TO PROVIDE COMPLETE ELECTRICAL DEMOLITION OF EXISTING FUELING SYSTEM AND ALL ASSOCIATED

ACCESSORIES. REMOVE THE FOLLOWING DEVICES INCLUDING BUT NOT LIMITED TO THE FOLLOWING; DISPENSERS, PUMPS

(DISCONNECT & REMOVE BRANCH CIRCUITRY), JUNCTION BOXES, ELECTRIC VALVES, AND INSTRUMENTS/CONTROLS.

COORDINATE REMOVAL EFFORTS CLOSELY WITH CONTRACTOR OFFICER'S REPRESENTATIVE.

CONTRACTOR TO CLOSELY COORDINATE THE REMOVAL EFFORTS OF ALL EQUIPMENT/DEVICES SCHEDULED FOR REMOVAL

WITH CONTRACTOR OFFICER'S REPRESENTATIVE.

CONTRACTOR TO DEMOLISH ALL EXISTING JUNCTION BOXES (POWER & CONTROL) AND LOCAL CONTROL STATIONS

ASSOCIATED WITH THE FUELING SYSTEM EQUIPMENT REMOVALS. CONTRACTOR TO REMOVE ALL ASSOCIATED CIRCUITRY

(CONDUIT & CONDUCTORS) BACK TO SOURCE. CONTRACTOR TO FIELD VERIFY AND COORDINATE CLOSELY WITH

CONTRACTOR OFFICER'S REPRESENTATIVE. TYPICAL OF TWO (2) FUELING SYSTEMS.

CONTRACTOR TO COORDINATE FINAL DUCT BANK ROUTING/REQUIREMENTS WITH EXISTING FIELD CONDITIONS, PROPOSED

WORK, AND CONTRACTOR OFFICER'S REPRESENTATIVE PRIOR TO ROUGH-IN. TYPICAL OF ALL PROPOSED DUCT BANKS.

CONTRACTOR RESPONSIBLE TO RESTORE ALL DISTURBED SURFACES AS PART OF THIS PROJECT TO SIMILAR CONDITIONS OF

THAT BEFORE THE PROJECT COMMENCED. COORDINATE FINAL REQUIREMENTS WITH THE OWNER. REFER TO DUCT BANK

SECTION DETAIL FOR ADDITIONAL INFORMATION. TYPICAL OF ALL PROPOSED DUCT BANKS.

GENERAL NEW WORK NOTES:

1. REFER TO E-01 FOR ELECTRICAL LEGENDS, ABBREVIATIONS AND GENERAL PROJECT NOTES.

2. PROPOSED UG DUCT BANKS AND STRUCTURES SHOWN ARE APPROXIMATE IN LOCATION. ROUTE UG DUCT BANKS WITH

GENERAL ROUTING AS SHOWN ON PLANS. ROUTE DUCT BANKS AS NECESSARY TO AVOID CONFLICTS WITH SITE CONDITIONS

AND PROPOSED PIPING SYSTEMS.

3. PROVIDE A DEDICATED GROUNDING CONDUCTOR FOR ALL ELECTRICAL EQUIPMENT AND ASSOCIATED EQUIPMENT/DEVICES.

4. EQUIPMENT AND DEVICE LOCATIONS ARE SHOWN AS GENERAL IN NATURE. COORDINATE WITH THE CONTRACTOR OFFICER'S

REPRESENTATIVE FOR EXACT LOCATIONS.

5. REFER TO ELECTRICAL SINGLE LINE DIAGRAMS, FLOOR PLANS, RISER DIAGRAMS, SCHEDULES, & DETAILS FOR ADDITIONAL

INFORMATION/REQUIREMENTS.

6. REFER TO OVERALL SITE PLANS ON CONSTRUCTION CONTRACT DRAWINGS FOR ADDITIONAL SITE INFORMATION.

7. NOT ALL EXISTING SITE UTILITIES SHOWN FOR CLARITY.

8. COORDINATE PARKING & LAYDOWN AREA WITH THE CONTRACTOR OFFICER'S REPRESENTATIVE.

9. DUCT BANKS SHALL NOT BE LOCATED ABOVE OTHER PIPING SYSTEMS EXCEPT WHERE CROSSING. MAINTAIN NESC SEPARATION

BETWEEN UTILITIES.

10. REFER TO UNDERGROUND UTILITIES (GENERAL NOTES) ON SHEET E-01 FOR ADDITIONAL INFORMATION.

11. COORDINATE FINAL DUCT BANK LOCATIONS (PRIOR TO ROUGH-IN) WITH CONTRACTOR OFFICER'S REPRESENTATIVE TO AVOID

CONFLICT WITH PROPOSED WORK AND EXISTING CONDITIONS.

12. CONTRACTOR TO COORDINATE ALL ASPECTS OF SEQUENCE OF CONSTRUCTION WITH THE CONTRACTOR OFFICER'S

REPRESENTATIVE.

13. CONTRACTOR IS RESPONSIBLE FOR ALL SITE RESTORATION. REFER TO TYPICAL DUCT BANK SECTION DETAILS FOR ADDITIONAL

INFORMATION.

GENERAL SECURITY NOTES:

AutoCAD SHX Text

GILLESPIE ROAD

AutoCAD SHX Text

PARKER ROAD

AutoCAD SHX Text

MONROE STREET

AutoCAD SHX Text

BUFFINGTON STREET

AutoCAD SHX Text

POOL

AutoCAD SHX Text

WESTERVELT AVENUE

AutoCAD SHX Text

HUDSON RIVER

AutoCAD SHX Text I-787

AutoCAD SHX Text

DALLIBA AVENUE

AutoCAD SHX Text

FARLEY DRIVE

AutoCAD SHX Text E-02

AutoCAD SHX Text

ELECTRICAL OVERALL SITE - PLAN

AutoCAD SHX Text

OVERALL SITE - PLAN

AutoCAD SHX Text

SCALE: 1" = 200'-0"

AutoCAD SHX Text 400'

AutoCAD SHX Text 200'

AutoCAD SHX Text

AutoCAD SHX Text

ENLARGED SITE - PLAN

AutoCAD SHX Text

SCALE: 1" = 50'-0"

AutoCAD SHX Text 100'

AutoCAD SHX Text 50'

AutoCAD SHX Text