MEO_d1986.pdf

MAINTENANCE ENGINEERING ORDER

(AMCOM Reg. 750-2)

MEO NO.

DATE PAGE 1 of

TITLE Tolerances Unless otherwise noted, dimensions are in inches and tolerances are:

Fractional ………………… ± 1/32 Decimal ………………... ± 0.010 Angular ………………… ± ½°

APPLICABILITY CSI Critical Characteristic Affected?

Impact Statement Attached?

REFERENCES FOR RDECOM USE ONLY

DOCUMENT(S) AFFECTED

PURPOSE OR PROBLEM

PROJECT ENGINEER ENGINEERING REVIEW ENGINEERING RELEASE

MED FORM 5-DEC-09 1401-R-E

D 1986 Apr 19, 2017 7

IUID Parts Marking for Chapter 1, Variable Displacement Axial Piston Pump Assembly, P/Ns PV3-075-20 (145HS100-3) and PV3-075-20A

(145HS100-5)

Technical

INTERIM USE OF THIS MEO IS AUTHORIZED

UNTIL AFFECTED DOCUMENT IS UPDATED.

MEO CHANGE TYPE

4) Normal - Can be implemented with normal priorityPRIORITY IMPLEMENTATION CATEGORY

CH47 DAA

DMWR 55-4320-278 dated 15 April 2016 TN 165683 8/29/2016

DOCUMENT CHANGE IS REQUIRED Verification: Hands-On Table-Top None

Changes based on IUID MEO review (TN 165347). Implement MEOs D1986, D1988 and D1989 concurrently.

CASTILLO.NO

EL.1089736990

Digitally signed by

CASTILLO.NOEL.1089736990

DN: c=US, o=U.S. Government, ou=DoD, ou=PKI, ou=USA, cn=CASTILLO.NOEL.1089736990 Date: 2016.09.01 10:23:46 -05'00'

NOLEN.OTIS.

F.1231157146

Digitally signed by

NOLEN.OTIS.F.1231157146

DN: c=US, o=U.S. Government, ou=DoD, ou=PKI, ou=CONTRACTOR, cn=NOLEN.OTIS.F.1231157146 Date: 2016.09.01 10:17:37 -05'00'

Otis Nolen (Camber Corporation)

PETER.ROBERT.

ARTHUR.JR.108

7823942

Digitally signed by

PETER.ROBERT.ARTHUR.JR.1087823942

DN: c=US, o=U.S. Government, ou=DoD, ou=PKI, ou=USA, cn=PETER.ROBERT.ARTHUR.JR.108782394 Date: 2016.09.20 10:10:27 -05'00'

Noel Castillo Robert A. Peter, Jr.

PUBLICATION CHANGE REQUEST: REQUEST THAT THE FOLLOWING DATA BE INCLUDED IN THE NEXT

CHANGE OR REVISION TO THE PUBLICATION IDENTIFIED ABOVE.

WP NO. PAGE

NO.

PARA-

GRAPH

FIGURE/

TABLE

NO.

CHANGES

(EXACT WORDING OF CHANGES MUST BE GIVEN)

1-6.d.(1) (a)

REPLACE paragraph to read:

“(a) A Construct 1 UII shall be encoded into an ECC 200 compliant 2-D data matrix. The CAGE and Unique Component Number (UCN) shall be acquired from AMCOM's The Army Maintenance Management System - Aviation (TAMMS-A/MCDS), Unique Identification (UID) database at https://tamms-a.redstone.army.mil. The Text Element Identifiers (TEIs) SPL and UCN shall be used as the data qualifiers. The component's manufacturer serial number as found at PSA (minus any maintenance inspection codes) shall not be used to develop the UII, but shall reside as HRI on the IUID data plates (Reference Figure 1-6, Sheet 3 of 4 for SPL and UCN configuration).”

Distribution Statement D:- Distribution authorized to Department of Defense and U.S. DoD contractors only to protect critical technology effective as of 26 June 2014. Other requests for this document must be referred to U.S. Army Aviation and Missile Research, Development and Engineering Center, ATTN: RDMR -AEM , Corpus Christi, TX 78419-5211

MED FORM 24 FEB 2016

Continuation Sheet

MEO NO.

PAGE of

WP NO. PAGE

NO.

PARA-

GRAPH

FIGURE/

TABLE

NO.

CHANGES

(EXACT WORDING OF CHANGES MUST BE GIVEN)

MED FORM 15-DEC-09 1401-R-E

1-6.d.(2)

1-6.d.(2) (b)

1-6.d.(3)

REPLACE paragraph to read:

“(2) If the Variable Displacement Axial Piston Pump Assembly has an original identification data plate, an UII is registered in the DoD IUID Registry (whether or not OPM IUID labels are present), and the registry record matches data on the component (paragraph 3-7), IUID data plates (paragraph 1-6.c) shall be fabricated in the format of Option B or C, Figure 1-6, Sheets 3 and 4 of 4, using the data as found in the DoD IUID Registry record. OPM IUID labels, if applicable, shall be removed from the component, however they may be kept with the component's documentation for reference only.”

“(b) The second ECC 200 compliant 2-D data matrix shall be encoded with the current Boeing part number using the TEI PNR or DI 30P (current Part Number) as the data qualifier. The PNR or 30P is the component’s Boeing part number upon completion of the M&O event.”

“(3) If the Variable Displacement Axial Piston Pump Assembly has compliant IUID data plates, and the registry record data matches data on the component (paragraph 3-7), but the IUID data plates must be replaced due to damage and/or change to component data (e.g., part number roll, additional inspection code required, etc.), replacement IUID data plates (paragraph 1-6.c) shall be fabricated in the format of Figure 1-6, Option A, B or C, whichever is applicable. The newly fabricated IUID data plates shall replicate the originally installed IUID data plates with the exception of any data that may have changed as a result of the M&O event.”

D 1986

Continuation Sheet

MEO NO.

PAGE of

WP NO. PAGE

NO.

PARA-

GRAPH

FIGURE/

TABLE

NO.

CHANGES

(EXACT WORDING OF CHANGES MUST BE GIVEN)

MED FORM 15-DEC-09 1401-R-E

1-6.d.(3) (b)

1-6.d.(4)

1-6.e

1-6.e Note

REPLACE paragraph to read:

“(b) The second ECC 200 compliant 2-D data matrix shall be encoded with the current Boeing part number using the TEI PNR or DI 30P (current Part Number) as the data qualifier. The PNR or 30P is the component’s Boeing part number upon completion of the M&O event.”

REPLACE paragraph 1-6.d.(4) to read:

“(4) If the Variable Displacement Axial Piston Pump Assembly has compliant IUID data plates, are registered in the DoD IUID Registry and the registry record matches data on the component (paragraph 3-7), the IUID data plates are undamaged, and no data changes are required, the IUID data plates can be reapplied to the component on which it was applied at PSA, provided the MRI meets the verification requirement for minimum print quality grade per MIL-STD-130. As an exception, the grading requirements for verification of laser etched black anodized aluminum plates can be per Table 1-1. If the 2-D data matrices do not meet the minimum grade requirements, replacement IUID data plate shall be fabricated 1-6.d.

ADD paragraph “1-6.e. IUID Data Plate Application ” after paragraph 1-6.d.(5).

REPLACE first Note after paragraph 1-6.e to read:

"NOTE

If applying overcoat to the IUID data plates prior to installation, refer to paragraph 1-6.e(2)."

Continuation Sheet

MEO NO.

PAGE of

WP NO. PAGE

NO.

PARA-

GRAPH

FIGURE/

TABLE

NO.

CHANGES

(EXACT WORDING OF CHANGES MUST BE GIVEN)

MED FORM 15-DEC-09 1401-R-E

1-6.e.(1)

1-6.e.(2)

1-6.e.(3)

1-6.f

Figure 1-6

CHANGE existing paragraph number “(6)” to read: “(1)”.

CHANGE existing paragraph number “(7)” to read: “(2)”.

CHANGE existing paragraph number "(8)" to read: "(3)".

CHANGE existing paragraph “(e)” to read: “(f)”.

REPLACE Figure 1-6, Sheet 2 of 4 with figure found on page 5 of this

MEO

REPLACE Figure 1-6, Sheet 3 of 4 with figure found on page 6 of this

REPLACE Figure 1-6, Sheet 4 of 4 with figure found on page 7 of this

Continuation Sheet

MEO NO.

PAGE of

MED FORM 15-DEC-09 1401-R-E

NOTES:

1. IF THE ITEM ARRIVES WITHOUT A REGISTERED UII, IUID DATA PLATES SHALL BE FABRICATED IN THE FORMAT OF

OPTION B AND INSTALLED IN PLACE OF THE ORIGINAL IDENTIFICATION DATA PLATE.

2. IF THE ITEM ARRIVES WITH ORIGINAL IDENTIFICATION DATA PLATE AND HAS A DOD REGISTERED UII, THE ORIGINAL IDENTIFICATION DATA PLATE AND ANY OPM IUID LABELS SHALL BE REPLACED WITH IUID DATA PLATES IN THE FORMAT OF OPTION B OR C. THE UII SHALL BE REPLICATED USING THE DOD IUID REGISTRY DATA. NO OPM IUID

LABELS SHALL REMAIN ON THE PART.

3. IF THE ITEM ARRIVES WITH A REGISTERED UII ON COMPLIANT IUID DATA PLATES (OPTION A, B OR C), IUID DATA PLATES SHALL BE REPLICATED (TO CONFIGURATION/FORMAT FOUND AT PSA) WHEN REPLACEMENT IS NECESSARY DUE TO DAMAGE AND/OR CHANGE TO COMPONENT DATA (E.G., PART NUMBER ROLL, ADDITIONAL INSPECTION CODE REQUIRED, ETC…). OPTION A MAY ARRIVE ON THE ITEM WITHOUT AN MII FIELD; PLACE AN MII FIELD ON THE

REPLICATED/REPLACEMENT IUID DATA PLATE AS SHOWN.

27807600

OPTION C

MFR XXXXX

SER XXXXXXXX

MII

Eaton Aerospace EATON PUMP, HYD. VAR

PUMP, HYD. VAR

MODEL NO. PV3-075-20A

P/N 3030434-001 SPEC NO. 145HS100

GPM 16.35 FLUID 83282-A

PSI 3060 RPM 5358

CONTRACT NO. Eaton Aerospace, Jackson, MS, U.S.A.

Eaton Aerospace Hydraulic Systems Divisions EATON

PNR 145HS100-5

77272 SOCN 145HS100-X

NSN

OPTION A

OPTION B

PUMP, HYD. VAR

MODEL NO. PV3-075-20A

P/N 3030434-001 SPEC NO. 145HS100

GPM 16.35 FLUID 83282-A

PSI 3060 RPM 5358

CONTRACT NO. Eaton Aerospace, Jackson, MS, U.S.A.

Eaton Aerospace Hydraulic Systems Divisions

EATON

PNR 145HS100-5

77272 SOCN 145HS100-X

NSN

Eaton Aerospace EATON PUMP, HYD. VAR

SPL XXXXX

UCN XXXXXXXX

S/N

MII

PUMP, HYD. VAR

MODEL NO. PV3-075-20A

P/N 3030434-001 SPEC NO. 145HS100

GPM 16.35 FLUID 83282-A

PSI 3060 RPM 5358

CONTRACT NO. Eaton Aerospace, Jackson, MS, U.S.A.

Eaton Aerospace Hydraulic Systems Divisions EATON

(30P) 145HS100-5

77272 SOCN 145HS100-X

NSN

Eaton Aerospace EATON PUMP, HYD. VAR

(17V) XXXXX

(1P) XXXXXXXX

(S) XXXXXX

MII

Figure 1-6. IUID Data Plates (Sheet 2 of 4)

MED FORM 24 FEB 2016

Continuation Sheet

MEO NO.

PAGE of

MED FORM 15-DEC-09 1401-R-E

NOTES:

1. ALL DIMENSIONS IN INCHES.

2. DRAWING NOT TO SCALE. USE LARGEST FONT SIZE THAT FITS FIELD AREA.

3. IUID MARKING PER MIL-STD-130.

4. LASER MARK .001 DEEP MAX ON BLACK ANODIZED PER MIL-A-8625.

5. MATERIAL: ALUMINUM ALLOY 1100-O, PER ASTM B209, STOCK 0.032 INCH +/- 0.0015 INCH THICK.

6. ALL TEXT TO BE UPPER GOTHIC.

7 QUIET ZONE (FREE SPACE) AROUND THE 2-D MATRIX CODE SHALL BE 0.050 MINIMUM IN ALL DIRECTIONS.

8 2-D DATA MATRIX CODE TO CONTAIN THE BOEING CURRENT PART NUMBER (PNR) AFTER AN M&O EVENT.

9 2-D DATA MATRIX CODE TO CONTAIN MFR (MANUFACTUER CAGE CODE) AND SER (MANUFACTURE SERIAL

NUMBER).

10 2-D DATA MATRIX CODE TO CONTAIN THE SPL XXXXX (CAGE CODE OF THE ENITIY SUPPLYING THE UII) AND

UCN (UNIQUE COMPONENT NUMBER OF THE ENITIY SUPPLYING THE UII).

11. FOR METAL PHOTOGRAPHIC PROCESS: USE PHOTOSENSITIVE ANODIZED ALUMINUM PER GG-P-455, TYPE I, CLASS 1, GRADE A.

12. OVERCOAT (683-3-2 OR 683-3-20) MAY BE APPLIED PRIOR TO INSTALLATION, REFER TO PARAGRAPH 1-6.e.(2).

.125 R 4 pls

MFR XXXXX

SER XXXXXXXX

MII

Eaton Aerospace EATON PUMP, HYD. VAR 7 9

2.00

0.60

.125 R 4 pls

PUMP, HYD. VAR

MODEL NO. PV3-075-20A

P/N 3030434-001 SPEC NO.

145HS100

GPM 16.35 FLUID 83282-A

PSI 3060 RPM 5358 Eaton Aerospace, Jackson, MS, U.S.A.

Eaton Aerospace Hydraulic Systems Divisions

PNR 145HS100-5

77272 SOCN 145HS100-X

NSN

EATON

2.00

7 8

0.60

OPTION A (Local Fabrication)

OPTION B (Local Fabrication)

2.00

PUMP, HYD. VAR

MODEL NO. PV3-075-20A

P/N 3030434-001 SPEC NO. 145HS100

GPM 16.35 FLUID 83282-A

PSI 3060 RPM 5358

CONTRACT NO. Eaton Aerospace, Jackson, MS, U.S.A.

Eaton Aerospace Hydraulic Systems Divisions

PNR 145HS100-5

77272 SOCN 145HS100-X

NSN

EATON

0.60

7 8.125 R 4 pls

.125 R 4 pls

Eaton Aerospace EATON PUMP, HYD. VAR

SPL XXXXX

UCN XXXXXXXX

S/N

MII

7 10

2.00

0.60

Figure 1-6. IUID Data Plates (Sheet 3 of 4)

MED FORM 24 FEB 2016

Continuation Sheet

MEO NO.

PAGE of

MED FORM 15-DEC-09 1401-R-E

NOTES:

1. ALL DIMENSIONS IN INCHES.

2. DRAWING NOT TO SCALE. USE LARGEST FONT SIZE THAT FITS FIELD AREA.

3. IUID MARKING PER MIL-STD-130.

4. LASER MARK .001 DEEP MAX ON BLACK ANODIZED PER MIL-A-8625.

5. MATERIAL: ALUMINUM ALLOY 1100-O, PER ASTM B209, STOCK 0.032 INCH +/- 0.0015 INCH THICK.

6. ALL TEXT TO BE UPPER GOTHIC.

7 QUIET ZONE (FREE SPACE) AROUND THE 2-D MATRIX CODE SHALL BE 0.050 MINIMUM IN ALL

DIRECTIONS.

8 2-D DATA MATRIX ENCODED WITH BOEING’S CURRENT PART NUMBER USING DI (30P) AFTER AN

M&O EVENT.

9 2-D DATA MATRIX ENCODED WITH CONSTRUCT 2 UII USING DIs, (17V) (MANUFACTURER’S CAGE

CODE), (1P) (ORIGINAL PART NUMBER) AND (S) (MANUFACTURER’S SERIAL NUMBER).

10. FOR METAL PHOTOGRAPHIC PROCESS: USE PHOTOSENSITIVE ANODIZED ALUMINUM PER

GG-P-455, TYPE I, CLASS 1, GRADE A.

11. OVERCOAT (683-3-2 OR 683-3-20) MAY BE APPLIED PRIOR TO INSTALLATION, REFER TO PARAGRAPH 1-6.e.(2).

27807800

2.00

PUMP, HYD. VAR

MODEL NO. PV3-075-20A

P/N 3030434-001 SPEC NO. 145HS100

GPM 16.35 FLUID 83282-A

PSI 3060 RPM 5358

CONTRACT NO. Eaton Aerospace, Jackson, MS, U.S.A.

Eaton Aerospace Hydraulic Systems Divisions

(30P) 145HS100-5

77272 SOCN 145HS100-X

NSN

EATON

0.60

7 8 .125 R 4 pls

.125 R 4 pls

Eaton Aerospace EATON PUMP, HYD. VAR

(17V) XXXXX

(1P) XXXXXXXX

(S)

MII

7 10

2.00

0.60

OPTION C (Local Fabrication)

Figure 1-6. IUID Data Plates (Sheet 4 of 4)

MED FORM 24 FEB 2016