Attachment_0025_8796522_Distribution_A.pdf

D

C

B

A

D

C

B

A

8 7 6 5 4 3 12

DESIGN ACTIVITY

SIZE CAGE CODE

SCALE UNIT WT.

DRAWN BY DATE(YEAR-MO-DA)

CHECKER ENGINEER

ENGINEER QUALITY ENGINEER

DRAWING APPROVAL

DESIGN APPROVALMATL ENGR MODELED BY

CONTRACT NUMBER

CONTRACTOR

SHEET

DRAWING SIZE D

TOLERANCES ON ANGLES �#� �$�

2 PLACE DECIMALS �#�

3 PLACE DECIMALS �#�

FORMAT: D_TACOM_ENG_1_0 12345678

DWG NO.

DIMENSION H

REVISIONS

APPROVEDDATE (YEAR-MO-DA)DESCRIPTIONREVISION

GJC2017-04-26

REDRAWN WITH CHANGE

NOR R16K2017 / 2017-04-20

BU

879652219203D

MARKING DIAGRAM AND

SEALING FOR WOOD

PACKING BOXES

US ARMY

PICATINNY ARSENAL

DOVER, NEW JERSEY

2017-04-20T. CORADESCHI

2017-04-20J. SLIKER

D. WALLSB. PETERS

1947-08-21R. BROWN

APPLICATION

USED ONNEXT ASSY

PMIC

MECHANICAL

PROPERTIES

YP

TS

EL2

RA

BH

RH R. BROWN

THIRD ANGLE PROJECTION

UNLESS OTHERWISE SPECIFIED

DIMENSIONS ARE IN INCHES

DO NOT SCALE DRAWING

PART NO. 8796522

THIS DRAWING WAS GENERATED FROM A SOLID MODEL

AND IS CAD MAINTAINED. CHANGES SHALL BE

INCORPORATED BY THE DESIGN ACTIVITY.

NSN

CURRENT DESIGN ACTIVITY CAGE CODE 19200

US ARMY

ARMAMENT RESEARCH, DEVELOPMENT AND ENGINEERING CENTER

PICATINNY ARSENAL, NEW JERSEY 07806-5000

REV STATUS

OF SHEETS

REV BU BU BU

SHEET 1 2 3

FIGURE 1

DISTRIBUTION STATEMENT A. APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.

MARKING ON SIDE OF BOX

NOTE M18 NOTE M18D

NOTE M21

NOTE M17

NOTE M16

NOTE M15

NOTE M14

NOTE M11

POP 5NOTE M10

NOTE M9 NOTE M8

MARKING ON TOP OF BOX

MARKING ON BOTH ENDS OF BOX

NOTE M19

NOTE M22

NOTE M20

POP 3

POP 2

MARKING ON OPPOSITE SIDE OF BOX

MARKING ON TOP OF SMALL BOX

NOTE M8

NOTE M10 NOTE M9

NATO SYMBOL OF INTERCHANGEABILITY

NOTE M21

DIMENSION H: NOT LESS THAN HEIGHT NOR MORE

THAN TWICE HEIGHT OF NOMENCLATURE MARKING

ONLY MARK WHEN SPECIFIED ON THE

ITEM PACKING AND MARKING DRAWING

H/10 = R

H/10 = R

SOLID COLOR

B

A

D

C

B

A

8 7 6 5 4 3 12

DESIGN ACTIVITY

SIZE CAGE CODE

SCALE UNIT WT. SHEET

DRAWING SIZE D

FORMAT: D_TACOM_ENG_1_0 12345678

DWG NO.

PART NO. 8796522

879652219203D

MARKING DIAGRAM AND

SEALING FOR WOOD

PACKING BOXES

US ARMY

PICATINNY ARSENAL

DOVER, NEW JERSEY

REVISIONS

APPROVEDDATE (YEAR-MO-DA)DESCRIPTIONREVISION

GJC2017-04-26

REDRAWN WITH CHANGE

NOR R16K2017 / 2017-04-20

BU

PACKAGING COMPONENTS:

SEAL, METALLIC - 8794342

PACKING FOR LIGHT BOXES - 9325874

NOTES:

1. MATERIAL: INK, STENCIL, BLACK NO. 37038, TYPE II, III, OR IV, IAW CID A-A-208.

A. ALTERNATIVE MATERIAL: INK, BLACK NO. 37038, IAW CID A-A-59383.

B. ALTERNATIVE MATERIAL: PAINT, STENCIL, FLAT, BLACK NO. 37038, IAW CID A-A-1558.

2. MATERIAL: INK, STENCIL, ORANGE NO. 32246, TYPE II, III, OR IV, IAW CID A-A-208.

A. ALTERNATIVE MATERIAL: INK, ORANGE NO. 32246, IAW CID A-A-59383.

B. ALTERNATIVE MATERIAL: PAINT, STENCIL, FLAT, ORANGE NO. 32246, IAW CID A-A-1558.

3. MATERIAL: STRAPPING, FLAT, REGULAR DUTY AND SEALS PER ASTM D3953.

A. FINISH B (GALVANIZED), GRADE 2, TYPE I USED FOR OCONUS (LEVEL A OR B).

B. FINISH A (ORGANIC) MAY BE USED FOR INTERPLANT SHIPMENTS OR ITEMS THAT ARE PACKED

COMMERCIALLY ONLY. (CONUS USE ONLY.)

4. MATERIAL: STRAPPING, WIRE, ROUND, CLASS 1, HARD PER ASTM A641/A641M.

A. WIRE OF DIAMETER BETWEEN 0.04 AND 0.182 INCHES MAY BE USED.

B. THE STRAPPING USED SHALL PASS THE NOMINAL DIAMETER, TENSILE STRENGTH, AND COATING

TESTS OF ASTM A641/A641M.

C. TENSILE STRENGTH REQUIRED: 90,000 PSI MIN.

5. MATERIAL: STRAPPING, NON-METALLIC, TYPE Ill OR IV OF ASTM D3950.

6. MATERIAL: LABEL, BAR CODE IAW DRAWING 12999545.

MARKING INSTRUCTIONS:

M1. THE MARKING OF WOOD SHIPPING BOXES FOR AMMUNITION ITEMS SHALL BE PLACED ON TOP, ONE LONG SIDE, AND BOTH ENDS (BOTH ENDS TO BE MARKED ALIKE) IAW TYPICAL MARKING DIAGRAMS, NOTES, AND MARKING INSTRUCTIONS CONTAINED ON THIS DRAWING AND APPLICABLE PACKING AND

MARKING BOX DRAWING.

M2. LETTERS AND FIGURES SHALL BE MARKED WITH BLACK STENCIL INK (NOTE 1). MARKING SHALL BE APPLIED BY STAMPING, STENCILING, OR ROLLER COATING. HAND LETTERING OR LABELING OF EXTERIOR CONTAINERS IS NOT AUTHORIZED FOR AMMUNITION AND EXPLOSIVE (CLASS V) ITEMS.

M3. THE DESIRED HEIGHT OF LETTERS AND FIGURES AND MINIMUM SIZE ALLOWED ARE AS FOLLOWS:

MARKING: DESIRED SIZE MINIMUM SIZE

A. NATIONAL STOCK NUMBER AND

DOD IDENTIFICATION CODE (DODIC) 1 INCH (25 MM) HIGH 7/16 INCH (11 MM) HIGH

B. LOT NUMBER 1 INCH (25 MM) HIGH 7/16 INCH (11 MM) HIGH

THE LETTERS AND FIGURES OF THE LOT NUMBER MAY BE 7/16 INCH (11 MM) MIN HEIGHT ON

CLEATS OF SHALLOW DEPTH BOXES AND ON SIDE OF BOXES ONLY IN CASES WHERE ALLOWABLE

SPACE IS INSUFFICIENT FOR 1 INCH (25 MM) CHARACTERS.

C. DESCRIPTIVE NOMENCLATURE,

CALIBER, AND WEAPON DESIGNATION 1 INCH (25 MM) HIGH 7/16 INCH (11 MM) HIGH

D. ALL OTHER MARKING 1 INCH (25 MM) HIGH 7/16 INCH (11 MM) HIGH

E. THE SIZES AND SPACES OF LETTER BLOCKS ARE REPRESENTATIVE OF STANDARD MACHINE CUT

STENCIL LETTERING.

F. DEVIATIONS IN SIZE OF LETTERS AND FIGURES WITHIN LIMITS SPECIFIED ABOVE WILL BE

PERMITTED ONLY WITH GOVERNMENT APPROVAL.

G. THE SIZE OF THE LETTERING SELECTED SHALL BE THE LARGEST PRACTICAL FOR THE PACKAGE

SIZE WITHIN THE ACCEPTABLE RANGE OF THE DESIRED SIZE AND THE MINIMUM. IF THE

NOMENCLATURE MARKINGS CANNOT FIT ON ONE LINE, THEN A SECOND LINE MAY BE USED.

H. THE RELATIVE POSITIONS OF THE VARIOUS MARKINGS SHALL BE AS SHOWN. STRAP POSITIONS AND MARKING SCHEME SHALL BE PLANNED OUT AHEAD OF TIME, SO THAT THE STRAPPING DOES NOT INTERFERE WITH BOX MARKINGS. MARKINGS WILL BE SEPARATED, AS NEEDED, TO PROVIDE

A 1.5 INCH (38 MM) VERTICAL AREA, VOID OF MARKINGS, WHERE THE STRAP(S) WILL BE

PLACED ONCE SECURED.

J. THE MARKING BLOCKS (�o�) SHOWN ARE FOR ILLUSTRATION PURPOSES ONLY AND DO NOT

NECESSARILY REPRESENT THE REQUIRED INFORMATION TO BE ENTERED.

K. LETTER SIZE FOR POP SYMBOL INFORMATION MUST BE AT LEAST 1/2 INCH (12 MM) HIGH FOR BOXES WEIGHING OVER 30 KG (66 LB). FOR BOXES UNDER 30 KG (66 LB), THE LETTER SIZE MAY BE REDUCED TO A MINIMUM OF 1/4 INCH (6 MM) IF ABSOLUTELY NECESSARY DUE TO SPACE

RESTRAINTS.

L. PUNCTUATION MARKS [E.G., COMMAS (,), PERIODS (.)] SHALL NOT BE MARKED IN THE

DESCRIPTIVE NOMENCLATURE (M17) UNLESS SPECIFICALLY INSTRUCTED. EXCEPTION: THE

MARKINGS FOR THE PROPER SHIPPING NAME (PSN) WILL INCLUDE ALL PUNCTUATION.

M. IF DETAILED MARKING INSTRUCTIONS PROVIDED IN THE CONTRACT OR PURCHASE ORDER

CONFLICT WITH THE INSTRUCTIONS ON THIS DRAWING, THEN THEY SHALL TAKE PRECEDENCE OVER

THE INSTRUCTIONS CONTAINED ON THIS DRAWING.

M4. WHEN HINGE AND HASP FITTINGS ARE USED, THE MARKING SHALL APPEAR ON THE SIDE TO WHICH

THE HASP IS FASTENED.

M5. WHEN FLAT BAND STRAPPING IS USED, LOCATE MARKING WITH CLEAR SPACE 1 INCH (25 MM) WIDE

AT STRAPPING LOCATION.

M6. THE WORDS "FLASHLESS" OR "SMOKELESS," WHEN REQUIRED IN THE DESCRIPTIVE NOMENCLATURE OF

THE ITEM PACKED. WILL BE SPELLED OUT COMPLETELY. IF NOT PART OF THE DESCRIPTIVE

NOMENCLATURE, THEN THE WORDS "FLASHLESS" OR "SMOKELESS" MAY BE ABBREVIATED, WHEN

NECESSARY, AS FOLLOWS: "FLHLS" OR "SMKLS."

M7. MARKING SHALL NOT BE EMBOSSED OR INDENTED BELOW THE SURFACE OF THE WOOD.

M8. INSERT PSN AND IDENTIFICATION NUMBER AS REQUIRED BY PACKING AND MARKING BOX DRAWING.

PSN AND IDENTIFICATION NUMBER ARE TO BE SEPARATED WITH A SPACE. A SPACE SHALL ALSO BE BETWEEN THE "UN" (OR "NA") AND THE FOUR-DIGIT NUMERAL IN THE IDENTIFICATION NUMBER

(E.G., UN 0012, NOT UN0012).

A. THE PSN AND UN NUMBER (OR NA NUMBER) SHALL BE MARKED ON THE TOP OF THE PACKAGE IN A

CLEAR AREA AWAY FROM ANY OTHER BOX MARKINGS.

B. ALTERNATIVE: FOR SMALL BOX WITH TOP HANDLES, MAY BE PLACED ON SIDE OF BOX, SPACED

1/4 INCH MINIMUM FROM TOP EDGE, WITH OTHER MARKING PRESCRIBED FOR SIDE OF BOX

PLACED BELOW PROPER SHIPPING NAME/IDENTIFICATION NUMBER MARKING SPACED AS SHOWN.

C. THE PSN IS REQUIRED, EVEN THOUGH IT MAY BE IDENTICAL TO THE ITEM DESCRIPTION

(NOMENCLATURE) AND SPACED AWAY FROM THE OTHER IDENTIFICATION MARKINGS.

M9. APPLY THE STORAGE TEMPERATURE LIMIT INDICATED, WHEN PACKING ROCKET AMMUNITION

(INCLUDING ROCKETS, ROCKET MOTORS, AND JATO UNITS) CONTAINING NITROCELLULOSE

PROPELLANT. STORAGE TEMPERATURE LIMITS SHALL BE ENCLOSED IN A SQUARE WITH THE WORDS

"STORAGE TEMPERATURE LIMITS." THE TEMPERATURE SHALL BE INDICATED BY A FIGURE,

FOLLOWED BY THE LETTER "C" (CELSIUS) OR "F" (FAHRENHEIT), AS APPROPRIATE.

M10. NOSE END MARKING IS REQUIRED FOR ROCKET AMMUNITION (INCLUDING ROCKETS, ROCKET MOTORS AND JATO UNITS) AND WHITE PHOSPHORUS (WP) SMOKE ARTILLERY AMMUNITION. THE END OF THE BOX CONTAINING THE ROCKET NOSE OR ARTILLERY FUZE SHALL BE IDENTIFIED WITH THE MARKING "NOSE END." THE END OR SIDE EDGE OF BOX TOP OVER NOSE OF ROCKET AMMUNITION MUST BE

MARKED "NOSE END." MARKING MAY BE PLACED AT EITHER END OF BOX TO COINCIDE WITH

AMMUNITION POSITION.

M11. INSERT GROSS WEIGHT BY WEIGH ING TWO REPRESENTATIVE SAMPLES AND AVERAGING THE WEIGHT.

THE CAPITAL LETTERS "WT" SHALL PRECEDE THE NUMERICAL GROSS WEIGHT, EXPRESSED IN

POUNDS, ROUNDED TO THE NEAREST WHOLE NUMBER, FOLLOWED BY THE CAPITAL LETTERS "LBS."

M12. REMOVED.

M13. REMOVED.

M14. THE LOT NUMBER AND SERIAL NUMBER (MARKED ON SIDE OF CONTAINER): THE LOWER-MOST MARKING ON THE PACKAGE SIDE CONTAINING THE ITEM DESCRIPTION (NOMENCLATURE) SHALL BE THE AMMUNITION LOT NUMBER. THE LOT NUMBER SHALL BE PRECEDED BY THE WORD "LOT" AND SHALL BE UNDERLINED WITH A SOLID LINE APPROXIMATELY 0.13 INCH (3.3 MM) THICK. IF A

SERIAL NUMBER IS REQUIRED FOR THE ITEM(S), THEN THE WORD "SER" AND THE SPECIFIC

NUMBER(S) SHALL BE MARKED ABOVE THE LOT NUMBER.

M15. INSERT ZONE MARKING, IF APPLICABLE. THE ZONE MARKING WILL BE MARKED ON THE BOX WHEN

INDICATED ON THE PROJECTILE PACKED. SOLID SQUARES OF THE SAME COLOR AS THE OTHER

LETTERING ON THE BOX SHALL BE USED TO INDICATE THE WEIGHT ZONE OF ALL AMMUNITION.

M16. INSERT BURSTING CHARGE, IF APPLICABLE. THE BURSTING CHARGE WILL BE MARKED ON THE

BOXES OF ALL HIGH EXPLOSIVE AMMUNITION.

M17. INSERT APPROPRIATE QUANTITY, DESCRIPTIVE NOMENCLATURE, CALIBER, AND WEAPON

DESIGNATION AS SHOWN ON APPLICABLE PACKING AND MARKING BOX DRAWING.

M18. INSERT NATIONAL STOCK NUMBER AND DOD IDENTIFICATION CODE (DODIC) TO BE LOCATED AS

FOLLOWS:

A. CENTERED ON THE SPACE DIRECTLY BELOW THE HASP, IF ONE IS PRESENT. EXCEPTION: ON

SHALLOW DEPTH BOXES, THE NSN MAY BE IN LINE WITH THE HASP.

B. WILL READ ON ONE CONTINUOUS LINE BUT MAY BE PLACED BELOW HARDWARE ON SMALL BOXES OF

INSUFFICIENT LENGTH.

C. TO BE PLACED ON THE TOP LINE OF THE MARKING ON THE LONG SIDE OF THE BOX.

D. THE DODIC WILL BE SET APART FROM NSN BY A DASH.

M19. INSERT DOD IDENTIFICATION CODE (DODIC), IF APPLICABLE. DODIC STARTS AT BOTTOM OF

CLEAT OR END BATTEN (WIREBOUND BOXES).

M20. INSERT LOT NUMBER. THE WORD "LOT" SHALL NOT BE USED. LOT NUMBERS SHALL BE ON ONE OR TWO LINES, STARTING AT BOTTOM OF END CLEAT OR END BATTEN (WIREBOUND BOXES). WHEN

TWO LINES ARE USED, LOT NUMBER SHALL BE DIVIDED BETWEEN DATE DESIGNATION AND LOT

INTERFIX NUMBERS.

M21. MARK ONLY WHEN REQUIRED BY ITEM SPECIFICATION OR PACKING AND MARKING BOX DRAWING.

APPLY NATO SYMBOL OF INTERCHANGEABILITY TO LEFT (AS SHOWN) OR RIGHT OF NOMENCLATURE

ON LONG SIDE OF BOX USING SAME INK AND COLOR AS REQUIRED FOR LETTERING. IF

SPECIFIED, THEN SYMBOL MAY BE COMPLETELY ENCLOSED IN A BOX MADE FROM A SOLID BLACK

LINE APPROXIMATELY 1/8 INCH (3 MM) WIDE.

M22. ALL NON-MANUFACTURED WOOD USED WILL BE HEAT TREATED AND MARKED IN AN UNOBSTRUCTED AREA TO SHOW CONFORMANCE TO THE INTERNATIONAL PLANT PROTECTION CONVENTION STANDARDS

(IPPC) AND INTERNATIONAL STANDARD FOR PHYTOSANITARY MEASURES-15 (ISPM-15). THE

QUALITY MARK SHALL BE PLACED ON BOTH ENDS OF THE OUTER PACKAGING, BETWEEN THE END

CLEATS OR END BATTENS.

M23. IN ADDITION TO ALL OTHER MARKINGS, EVERY BOX SHALL HAVE A BAR CODE LABEL APPLIED TO

THE BOX IAW DRAWING 12999545. (SEE FIGURE 1.)

DISTRIBUTION STATEMENT A. APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.

B

A

D

C

B

A

8 7 6 5 4 3 12

DESIGN ACTIVITY

SIZE CAGE CODE

SCALE UNIT WT. SHEET

DRAWING SIZE D

FORMAT: D_TACOM_ENG_1_0 12345678

DWG NO.

PART NO. 8796522

879652219203D

MARKING DIAGRAM AND

SEALING FOR WOOD

PACKING BOXES

US ARMY

PICATINNY ARSENAL

DOVER, NEW JERSEY

REVISIONS

APPROVEDDATE (YEAR-MO-DA)DESCRIPTIONREVISION

GJC2017-04-26

REDRAWN WITH CHANGE

NOR R16K2017 / 2017-04-20

BU

CORRECTION OF MARKING AND RE-MARKING

WHEN MARKING IS TO BE CORRECTED OR RE-PLACED, THE OLD MARKING SHALL BE OBLITERATED, SO THAT NO "SHOW-THROUGH" IS VISIBLE. NEW MARKING SHALL BE APPLIED AS STATED HEREON. RE- MARKING THROUGHOUT A LOT SHALL BE UNIFORM, CLEAN, AND CLEARLY LEGIBLE. RE-MARKING TO CORRECT POOR WORKMANSHIP SHALL BE KEPT TO A MINIMUM. RE-MARKING MAY BE ACCOMPLISHED THROUGH COMPLETE OBLITERATION OF A PANEL OR SPOT OBLITERATION AS DEEMED ACCEPTABLE BY THE RESPONSIBLE GOVERNMENT ACTIVITY. OBLITERATING MATERIALS SUCH AS LACQUER, ENAMEL, OR

PAINTS SHALL APPROXIMATE THE COLOR OF THE CONTAINER.

MARKING INSTRUCTIONS FOR INTERPLANT SHIPMENT

MIS 1. WHEN THE ITEMS PACKED ARE INTENDED ONLY FOR INTERPLANT SHIPMENT, THE INFORMATION REQUIRED ON THIS DRAWING, EXCEPT FOR PROPER SHIPPING NAME AND IDENTIFICATION NUMBER

AND POP MARKING, MAY BE PLACED ON LABELS.

MlS 2. TWO LABELS SHALL BE SECURELY ATTACHED TO EACH BOX. ONE LABEL SHALL BE ATTACHED TO THE FRONT (HASP) SIDE AND ONE ON THE END OF THE BOX TO THE RIGHT OF THE FRONT. IF

END PLACEMENT IS IMPRACTICAL, THEN THE END LABEL MAY BE PLACED ON THE BOX TOP,

CLEARLY SEPARATED FROM PROPER SHIPPING NAME/IDENTIFICATION NUMBER MARKING.

MIS 3. LETTER HEIGHT SPECIFIED IN MARKING INSTRUCTIONS DO NOT APPLY TO LABELS.

MIS 4. LABELS SHALL BE ATTACHED BY ANY METHOD THAT WILL PERMIT EASY REMOVAL (E.G., TACKS, STAPLES).

MIS 5. PROPER SHIPPING NAME AND IDENTIFICATION NUMBER AND POP MARKING SHALL BE APPLIED

DIRECTLY TO THE BOX AS SHOWN IN NOTES M8 AND POP 2 / POP 3 ON THIS DRAWING.

MIS 6. WHEN SPECIFIED ON PACKING AND MARKING DRAWING, THE WORDS "FOR CONUS SHIPMENT ONLY"

SHALL BE APPLIED TO THE BOX, DIRECTLY BELOW THE POP MARKING.

MARKING INSTRUCTIONS FOR METAL PARTS SHIPMENT

MMP 1. WHEN METAL PARTS ARE SHIPPED IN END ITEM BOXES, MARKING INFORMATION WILL BE APPLIED

ON BOX LABELS.

MMP 2. ATTACH 2 LABELS. (NOTES MIS 2, MIS 3, AND MIS 4.)

MMP 3. LETTER HEIGHT SHALL BE 1/4 INCH MINIMUM.

MMP 4. THE FOLLOWING INFORMATION SHALL BE SHOWN:

PART NUMBER

(QUANTITY) (NOMENCLATURE)

LOT NO.

CONTRACT NO.:

WT:

MARKING INSTRUCTIONS FOR LESS-THAN-FULL BOXES

MLF 1. REMOVED.

MLF 2. A LIGHT (LITE) BOX SHALL BE IDENTIFIED AS SUCH BY MARKING OR STENCILING THE WORDS "LIGHT BOX" ("LITE BOX"), IN CONTRASTING ORANGE PAINT (SEE NOTE 2) SCHEME, ON THE

IDENTIFICATION SIDE, SPACE PERMITTING, IN THE LARGEST PRACTICAL SIZE LETTERS. AN

ADDITIONAL MARKING OR STENCILING SHALL BE PLACED ON THE TOP, SIDE, AND ENDS OF THE

BOX. IF THE BOTTOM IS VISIBLE DURING SHIPMENT, THEN THIS TOO SHALL BE MARKED.

MLF 3. FOR DEFINITION AND PACKING OF LIGHT BOX, SEE DRAWING 9325874 (REF).

MLF 4. REMOVED.

MARKING FOR PERFORMANCE ORIENTED PACKAGING

POP 1. WHEN SPECIFIED ON THE APPLICABLE PACKING AND MARKING DRAWING, PERFORMANCE ORIENTED

PACKAGING (POP) MARKINGS SHALL BE APPLIED TO THE SIDE OF THE BOX OPPOSITE THE

NOMENCLATURE MARKING. LETTERS AND CHARACTERS SHALL BE 1/2 INCH (12 MM) MINIMUM AND

THE SAME COLOR AS THE NOMENCLATURE MARKING (SEE NOTE 1).

POP 2. INSERT THE SYMBOL SHOWN. THE LETTERS "u" AND "n" SHALL BE LOWERCASE AND ENCLOSED IN A ClRCLE OF SUFFICIENT SIZE TO PROVIDE A MINIMUM CLEAR SPACE AROUND THE LETTERS "u" AND "n."

POP 3. THE UN POP MARKING CODE AS SPECIFIED ON THE PACKING AND MARKING DRAWING WILL BE

INSERTED TO THE RIGHT OF THE SYMBOL SHOWN.

POP 4. PERFORMANCE ORIENTED PACKAGING (POP) VERIFICATION. IN NO CASE SHALL A CONTAINER BE

SHIPPED, IF THE GROSS WEIGHT MARKED ON THE PACKAGE IS GREATER THAN THE POP

CERTIFIED WEIGHT. IF THE AVERAGE GROSS WEIGHT OF THE PACKED CONTAINERS (DETERMINED

BY WEIGHING TWO REPRESENTATIVE SAMPLES AND AVERAGING THE WEIGHT) IS GREATER THAN

THE CERTIFIED WEIGHT, THEN CONTAINER MARKING OPERATIONS SHALL CEASE, AND THE

PROCURING ACTIVITY SHALL BE CONTACTED IMMEDIATELY.

POP 5. IF THE EXTERIOR CONTAINER IS AN OVERPACK CONTAINING "POP" MARKED AND CERTIFIED

INNER CONTAINERS, THEN "OVERPACK" SHALL BE MARKED ON THE WOOD BOX. THE MARKING

SHALL BE A MINIMUM OF 2 INCHES (50 MM) HIGH.

SEALING INSTRUCTIONS (NAILED WOOD)

SN 1. METHOD OF SEALING HASP AND HINGE HARDWARE:

A. CLOSE COVER. FASTEN HASP WITH SWIVELS AND PASS METALLIC SEAL WIRE THROUGH

EYELETS OF HASPS AND SWIVELS.

B. WITH WIRE PULLED TIGHT, SECURE METALLIC SEAL WITH SEALING TOOL IAW DRAWING

8794342.

C. METALLIC SEAL SHALL BE APPLIED IN A MANNER THAT THE ONLY MEANS OF

OPENING/REMOVING THE SEAL WILL BE TO DESTROY THE SEAL OR TO CUT THE WIRE. ANY

IMPROPERLY CRIMPED AND/OR LOOSE SEALS DETECTED AT THE LOAD PLANT SHALL BE

DISCARDED, AND A NEW SEAL APPLIED CORRECTLY.

SN 2. REMOVED.

SN 3. STRAPPING OF BOX:

A. ALL BOXES SHALL BE STRAPPED GIRTHWISE, WITH THE STRAPPING BEING APPLIED OVER THE

SIDES, TOP, AND BOTTOM. UNLESS OTHERWISE SPECIFIED, BOXES LESS THAN 18 INCHES

(457 MM) IN OVERALL LENGTH SHALL HAVE ONE STRAP; BOXES 18 INCHES (457 MM) TO 36

INCHES (914 MM) IN LENGTH SHALL HAVE TWO STRAPS; AND BOXES OVER 36 INCHES (914

MM) IN LENGTH SHALL HAVE THREE STRAPS. STRAPPING SHALL BE EITHER ROUND WIRE (SEE

NOTE 4) OR FLAT STEEL (SEE NOTE 3). BOXES REQUIRING ONE STRAP SHALL HAVE THE

STRAP PLACED AT THE CENTER OF THE BOX OR ADJACENT TO THE HASP, WHEN HARDWARE IS

USED. BOXES REQUIRING TWO STRAPS SHALL HAVE THE STRAPS LOCATED JUST INSIDE THE

COVER CLEATS OR BETWEEN THE COVER CLEATS AND THE HINGES, WHEN HARDWARE IS USED.

BOXES REQUIRING THREE STRAPS SHALL HAVE TWO STRAPS PLACED AS DESCRIBED FOR THE

TWO-STRAP BOX AND THE THIRD STRAP PLACED AS DESCRIBED FOR A ONE-STRAP BOX. WHEN

A CENTER COVER CLEAT IS REQUIRED, THE THIRD STRAP SHALL BE PLACED BETWEEN THE

CLEAT AND THE HASP. STRAP POSITIONS AND MARKING SCHEME SHALL BE PLANNED OUT

AHEAD OF TIME, SO THAT THE STRAPPING DOES NOT INTERFERE WITH BOX MARKINGS.

MARKINGS WILL BE SEPARATED, AS NEEDED, TO PROVIDE A 1.5 INCH (38 MM) VERTICAL

AREA, VOID OF MARKINGS, WHERE THE STRAP(S) WILL BE PLACED ONCE SECURED.

B. THE LOCATION OF THE CONNECTORS IS OPTIONAL.

C. PULL TIGHT, UNTIL STRAPPING CUTS INTO THE EDGE OF THE BOX. FOR FLAT STRAPPING, SEAL STRAPPING WITH CONNECTOR (SEE NOTE 3). FOR ROUND WIRE STRAPPING, TWIST

CLOSED (SEE NOTE 4).

D. THE SIZE OF FLAT STEEL STRAPPING SHALL BE 5/8 INCH (15 MM) BY .020 INCH (0.51 MM)

FOR ALL BOXES EXCEPT TYPE I, CLASS 3. STRAPPING FOR TYPE I, CLASS 3 BOXES SHALL

CONSIST OF NOT LESS THAN TWO STRAPS 3/8 (9 MM) INCH BY .015 INCH (0.38 MM).

E. ALTERNATIVELY, FOR DOMESTIC USE (SEE NOTE 3B), NON-METALLIC STRAPPING (SEE NOTE

5) MAY BE USED ON ALL BOXES. SEALS SHALL BE IAW MANUFACTURER'S INSTRUCTIONS.

JOINED STRENGTH SHALL BE IAW ASTM D3950 (REF). SIZE OF STRAPPING SHALL BE 1/2

INCH (12 MM) BY .020 INCH (0.51 MM). UNLESS SPECIFIED, ALL AMMUNITION AND

EXPLOSIVE ITEMS (CLASS V) WILL BE PACKAGED FOR USE IN SHIPMENTS OCONUS (LEVEL A

OR B).

SEALING INSTRUCTIONS (WIREBOUND)

SW 1. METHOD OF SEALING BY CLOSING LOOPS:

A. WIREBOUND BOXES SHALL BE SEALED WITH A SALLEE CLOSER (AVAILABLE FROM ANY

WIREBOUND BOX SUPPLIER) AND THE FOLLOWING INSTRUCTIONS:

(1) CLOSE BOX SO THAT LOOP ON BOX SIDE PROTRUDES THROUGH CORRESPONDING COVER

LOOP.

(2) INSERT THE SALLEE CLOSER THROUGH SIDE LOOP AND CATCH TOP LOOP IN NOTCH ON END

OF TOOL.

(3) RAISE HANDLE OF SALLEE CLOSER TO SLIGHTLY BEYOND VERTICAL POSITION AND PUSH

TOP LOOP DOWN AGAINST SIDE OF BOX.

(4) COMPLETE CLOSING BY SWINGING HANDLE OF SALLEE CLOSER DOWN AS FAR AS POSSIBLE.

SW 2. METHOD OF SEALING WI TH METALLIC SEAL:

A. METALLIC SEAL (8794342) SHALL BE APPLIED TO WIREBOUND BOX AS SHOWN ON PROCEDURE 3

OF DRAWING 12977298-3.

B. REMOVED.

C. METALLIC SEAL SHALL BE APPLIED IN A MANNER THAT THE ONLY MEANS OF

OPENING/REMOVING THE SEAL WILL BE TO DESTROY THE SEAL OR TO CUT THE WIRE. ANY

IMPROPERLY CRIMPED AND/OR LOOSE SEALS DETECTED AT THE LOAD PLANT SHALL BE

DISCARDED, AND A NEW SEAL APPLIED CORRECTLY.

REPAIR INSTRUCTIONS (WIREBOUND)

ALL BROKEN LOOPS SHALL BE REPAIRED BEFORE SHIPMENT. REPAIR PROCEDURES SHALL BE AS

SPECIFIED IN APPROPRIATE BOX SPECIFICATION.

INSTRUCTIONS FOR RE-USE OF WOOD BOXES AND PACKAGING MATERIALS (INTERPLANT ONLY)

IR 1. RE-USE OF PACKAGING MATERIALS (EXCEPT PACKAGING MADE OF PAPER, PLASTIC FI LM, OR TEXTILES AND SPECIFICALLY BARRIER BAGS) IS PERMISSIBLE IF CONSIDERED ECONOMICALLY

FEASIBLE AND IN USABLE CONDITION BY THE PROCURING ACTIVITY.

IR 2. WOOD BOXES SHALL BE REJECTED FOR RE-USE UPON DETECTION OF ANY OF THE FOLLOWING:

A. CONTAMINATION FROM EXPLOSIVE MATERIAL, OIL, OR GREASE ON INTERIOR.

B. NAILS MISSING, LOOSE, OR MISSING KNOTS.

DISTRIBUTION STATEMENT A. APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.

u n u n