VA 620A4-22-101 Combined Drawing Set.pdf
PDF 16 MB Posted
- Attached to
- Y1DZ--620A4-22-101 Replace Fan Coils in Building 18 at the Castle Point VA Medical Center
- Solicitation number
- 36C24226B0001
About this file
This document is a comprehensive set of construction design and engineering drawings for a fan coil unit replacement project at the Castle Point VA Medical Center, Building 18. The project involves a fully sprinklered renovation to replace existing fan coil units across multiple floors, including basement, first, second, third floors, and the penthouse. The detailed drawing set includes architectural, mechanical, electrical, and abatement plans with specific focus on phasing the replacement of heating and cooling infrastructure while maintaining facility operations.
The project scope encompasses comprehensive mechanical system upgrades, including removing existing two-pipe fan coil units and replacing them with new four-pipe units from Daikin, updating piping distribution systems, modifying electrical connections, and implementing careful infection control measures. The design documents outline specific demolition and installation procedures for each floor, with meticulous attention to maintaining negative air pressure, managing dust control, and ensuring minimal disruption to the medical facility's ongoing functions. The project is scheduled for completion by December 10, 2024, with work to be performed under VA solicitation number 36C24226B0001.
View the file
Other files
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
Project Number
Building Number
Drawing Number
Project Title
Location
Issue Date Checked Drawn
Drawing Title
Approved:
VA FORM 08 - 6231
A
Office of Construction and Facilities Management
U.S. Department of Veterans Affairs
B
C
D
E
F
A
B
C
D
E
F
21 4 5 6 7 8 9 10
PhaseARCHITECT/ENGINEER OF RECORDCONSULTANT
321 4 5 6 7 8 9 10
Project Director
Revisions: Date:
TITLE SHEET & DRAWING INDEX CONTRACT DOCUMENTS
FULLY SPRINKLERED
REPLACE FAN COIL UNITS, BLDG 18
41 CASTLE POINT RD.
WAPPINGERS FALLS, NY 12590
2024-12-10
GI001
620A4-22-101
ELK KRL
REV 0 CONTRACT DOCUMENTS 2024/12/10
"Unauthorized alteration or addition to any plans, specifications or reports bearing a Licensed Professional Engineer's seal is a violation of Section 7209, subdivision 2, of the New York State Education Law".
CERTIFICATE OF AUTHORIZATION NUMBER: 0020000
CASTLE POINT VAMC
REPLACE FAN COIL UNITS
BUILDING 18
NORTH ARROW
DETAIL NUMBER
DETAIL IDENTIFIER
DETAIL TITLE NUMBER /
SHEET REF NUMBER
SECTION IDENTIFIER
SHEET REF NUMBER
DETAIL
IDENTIFIER
SHEET REF
NUMBER
DETAIL SECTION IDENTIFIER
VIEWING
DIRECTION
VIEW TITLE
BUILDING/WALL SECTION CUT
EXTERIOR ELEVATION
DETAIL SECTION CUT
DETAIL CALLOUT
DRAWING SYMBOLS
N
INTERIOR ELEVATION
DD###
DD###
X
DD###
X
SCALE: 1'-0" = 1'-0"
DETAIL TITLEX
1 / DD###
DD###
X
DD###
X
TRUE NORTH
PLAN NORTH
VIEWING
DIRECTION
SHEET REF NUMBER
SHEET REF NUMBER
DRAWING LIST
DRAWING
NUMBER DRAWING TITLE
GENERAL
GI001 TITLE SHEET & DRAWING INDEX
GC101 GENERAL PHASING PLAN - ROOF-PENTHOUSE
GC102 GENERAL PHASING PLAN - ROOF-CRAWLSPACE
GC103 GENERAL PHASING PLAN - BASEMENT FLOOR
GC104 GENERAL PHASING PLAN - FIRST FLOOR
GC105 GENERAL PHASING PLAN - SECOND FLOOR
GC106 GENERAL PHASING PLAN - THIRD FLOOR
GC107 GENERAL PHASING PLAN - ROOF-CRAWLSPACE
GC401 ICRA PLAN - PHASE 3 - RISER 1
GC402 ICRA PLAN - PHASE 3 - RISER 2
GC403 ICRA PLAN - PHASE 3 - RISER 3
GC404 ICRA PLAN - PHASE 3 - RISER 4
GC405 ICRA PLAN - PHASE 3 - RISER 5
GC406 ICRA PLAN - PHASE 3 - RISER 6
GC407 ICRA PLAN - PHASE 3 - RISER 7
GC408 ICRA PLAN - PHASE 3 - RISER 8
GC409 ICRA PLAN - PHASE 3 - RISER 9
GC410 ICRA PLAN - PHASE 3 - RISER 10
GC411 ICRA PLAN - PHASE 3 - RISER 11
GC412 ICRA PLAN - PHASE 3 - RISER 12
HAZARDOUS MATERIALS
H-101 ABATEMENT DESIGN PLAN - BASEMENT
H-121 ABATEMENT DESIGN PLAN - FIRST FLOOR
H-141 ABATEMENT DESIGN PLAN - SECOND FLOOR
H-161 ABATEMENT DESIGN PLAN - THIRD FLOOR
ARCHITECTURAL
A-001 ARCHITECTURAL NOTES & LEGENDS
AD121 ARCHITECTURAL DEMOLITION PLAN - FIRST FLOOR
AD141 ARCHITECTURAL DEMOLITION PLAN - SECOND FLOOR
AD161 ARCHITECTURAL DEMOLITION PLAN - THIRD FLOOR
AE121 ARCHITECTURAL PLAN - FIRST FLOOR
AE141 ARCHITECTURAL PLAN - SECOND FLOOR
AE161 ARCHITECTURAL PLAN - THIRD FLOOR
AE401 ARCHITECTURAL ENLARGED PLAN - FIRST FLOOR
AE501 ARCHITECTURAL WALL TYPES AND DETAILS
MECHANICAL
M-001 MECHANICAL NOTES AND LEGEND
MD101 MECHANICAL DEMOLITION PLAN - BASEMENT
MD121 MECHANICAL DEMOLITION PLAN - FIRST FLOOR
MD141 MECHANICAL DEMOLITION PLAN - SECOND FLOOR
MD161 MECHANICAL DEMOLITION PLAN - THIRD FLOOR
MD191 MECHANICAL DEMOLITION PLAN - ROOF-PENTHOUSE
MD406 MECHANICAL DEMOLITION PLAN - ROOF-PENTHOUSE
MH601 MECHANICAL SCHEDULES
MH602 MECHANICAL SCHEDULES
MI601 MECHANICAL CONTROLS DIAGRAMS
MI602 MECHANICAL CONTROLS DIAGRAMS
MP111 MECHANICAL PIPING PLAN - BASEMENT FLOOR AT CEILING
MP121 MECHANICAL PIPING PLAN - FIRST FLOOR
MP131 MECHANICAL PIPING PLAN - FIRST FLOOR AT CEILING
MP141 MECHANICAL PIPING PLAN - SECOND FLOOR
MP151 MECHANICAL PIPING PLAN - SECOND FLOOR AT CEILING
MP161 MECHANICAL PIPING PLAN - THIRD FLOOR
MP171 MECHANICAL PIPING PLAN - THIRD FLOOR AT CEILING
MP181 MECHANICAL PIPING PLAN - ROOF-CRAWLSPACE
MP191 MECHANICAL PIPING PLAN - ROOF-PENTHOUSE
MP201 MECHANICAL PIPING SCHEMATIC - ROOF-PENTHOUSE
MP301 MECHANICAL PIPING SECTIONS
MP401 MECHANICAL ENLARGED PIPING PLAN - ROOF PENTHOUSE
MP501 MECHANICAL PIPING DETAILS
MP601 MECHANICAL PIPING RISER - ROOF PENTHOUSE
MP602 MECHANICAL PIPING RISER - ROOF PENTHOUSE
MP603 MECHANICAL PIPING RISER - ROOF PENTHOUSE
ELECTRICAL
E-001 ELECTRICAL NOTES AND LEGENDS
ED101 ELECTRICAL DEMOLITION PLAN - BASEMENT
ED121 ELECTRICAL DEMOLITION PLAN - FIRST FLOOR
ED141 ELECTRICAL DEMOLITION PLAN - SECOND FLOOR
ED161 ELECTRICAL DEMOLITION PLAN - THIRD FLOOR
ED191 ELECTRICAL DEMOLITION PLAN - PENTHOUSE
EP101 ELECTRICAL POWER PLAN - BASEMENT
EP121 ELECTRICAL POWER PLAN - FIRST FLOOR
EP141 ELECTRICAL POWER PLAN - SECOND FLOOR
EP161 ELECTRICAL POWER PLAN - THIRD FLOOR
EP191 ELECTRICAL POWER PLAN - PENTHOUSE
Exp. 11/30/2027
23 Mechanic Street, Springville, NY 14141
12/10/2024
MULTICORELINK:DWG-22187-GC101.REVX GENERAL PHASING PLAN - ROOF-PENTHOUSE-DWG-22187-GC101.REVX GENERAL PHASING PLAN - ROOF-PENTHOUSE MULTICORELINK:DWG-22187-GC101.REVX GENERAL PHASING PLAN - ROOF-PENTHOUSE-DWG-22187-GC101.REVX GENERAL PHASING PLAN - ROOF-PENTHOUSE MULTICORELINK:DWG-22187-GC102.REVX GENERAL PHASING PLAN - ROOF-CRAWLSPACE-DWG-22187-GC102.REVX GENERAL PHASING PLAN - ROOF-CRAWLSPACE MULTICORELINK:DWG-22187-GC102.REVX GENERAL PHASING PLAN - ROOF-CRAWLSPACE-DWG-22187-GC102.REVX GENERAL PHASING PLAN - ROOF-CRAWLSPACE MULTICORELINK:DWG-22187-GC103.REVX GENERAL PHSNG PLN - BASEMENT FL-DWG-22187-GC103.REVX GENERAL PHSNG PLN - BASEMENT FL MULTICORELINK:DWG-22187-GC103.REVX GENERAL PHSNG PLN - BASEMENT FL-DWG-22187-GC103.REVX GENERAL PHSNG PLN - BASEMENT FL MULTICORELINK:DWG-22187-GC104.REVX GENERAL PHSNG PLN - FIRST FL-DWG-22187-GC104.REVX GENERAL PHSNG PLN - FIRST FL MULTICORELINK:DWG-22187-GC104.REVX GENERAL PHSNG PLN - FIRST FL-DWG-22187-GC104.REVX GENERAL PHSNG PLN - FIRST FL MULTICORELINK:DWG-22187-GC105.REVX GENERAL PHASING PLAN - SCND FL-DWG-22187-GC105.REVX GENERAL PHASING PLAN - SCND FL MULTICORELINK:DWG-22187-GC105.REVX GENERAL PHASING PLAN - SCND FL-DWG-22187-GC105.REVX GENERAL PHASING PLAN - SCND FL MULTICORELINK:DWG-22187-GC106.REVX GENERAL PHASING PLAN - THIRD FL-DWG-22187-GC106.REVX GENERAL PHASING PLAN - THIRD FL MULTICORELINK:DWG-22187-GC106.REVX GENERAL PHASING PLAN - THIRD FL-DWG-22187-GC106.REVX GENERAL PHASING PLAN - THIRD FL MULTICORELINK:DWG-22187-GC107.REVX GENERAL PHASING PLAN - ROOF-CRAWLSPACE-DWG-22187-GC107.REVX GENERAL PHASING PLAN - ROOF-CRAWLSPACE MULTICORELINK:DWG-22187-GC107.REVX GENERAL PHASING PLAN - ROOF-CRAWLSPACE-DWG-22187-GC107.REVX GENERAL PHASING PLAN - ROOF-CRAWLSPACE MULTICORELINK:DWG-22187-GC401.REVX ICRA PLAN - PHASE 3 - RISER 1-DWG-22187-GC401.REVX ICRA PLAN - PHASE 3 - RISER 1 MULTICORELINK:DWG-22187-GC401.REVX ICRA PLAN - PHASE 3 - RISER 1-DWG-22187-GC401.REVX ICRA PLAN - PHASE 3 - RISER 1 MULTICORELINK:DWG-22187-GC402.REVX ICRA PLAN - PHASE 3 - RISER 2-DWG-22187-GC402.REVX ICRA PLAN - PHASE 3 - RISER 2 MULTICORELINK:DWG-22187-GC402.REVX ICRA PLAN - PHASE 3 - RISER 2-DWG-22187-GC402.REVX ICRA PLAN - PHASE 3 - RISER 2 MULTICORELINK:DWG-22187-GC403.REVX ICRA PLAN - PHASE 3 - RISER 3-DWG-22187-GC403.REVX ICRA PLAN - PHASE 3 - RISER 3 MULTICORELINK:DWG-22187-GC403.REVX ICRA PLAN - PHASE 3 - RISER 3-DWG-22187-GC403.REVX ICRA PLAN - PHASE 3 - RISER 3 MULTICORELINK:DWG-22187-GC404.REVX ICRA PLAN - PHASE 3 - RISER 4-DWG-22187-GC404.REVX ICRA PLAN - PHASE 3 - RISER 4 MULTICORELINK:DWG-22187-GC404.REVX ICRA PLAN - PHASE 3 - RISER 4-DWG-22187-GC404.REVX ICRA PLAN - PHASE 3 - RISER 4 MULTICORELINK:DWG-22187-GC405.REVX ICRA PLAN - PHASE 3 - RISER 5-DWG-22187-GC405.REVX ICRA PLAN - PHASE 3 - RISER 5 MULTICORELINK:DWG-22187-GC405.REVX ICRA PLAN - PHASE 3 - RISER 5-DWG-22187-GC405.REVX ICRA PLAN - PHASE 3 - RISER 5 MULTICORELINK:DWG-22187-GC406.REVX ICRA PLAN - PHASE 3 - RISER 6-DWG-22187-GC406.REVX ICRA PLAN - PHASE 3 - RISER 6 MULTICORELINK:DWG-22187-GC406.REVX ICRA PLAN - PHASE 3 - RISER 6-DWG-22187-GC406.REVX ICRA PLAN - PHASE 3 - RISER 6 MULTICORELINK:DWG-22187-GC407.REVX ICRA PLAN - PHASE 3 - RISER 7-DWG-22187-GC407.REVX ICRA PLAN - PHASE 3 - RISER 7 MULTICORELINK:DWG-22187-GC407.REVX ICRA PLAN - PHASE 3 - RISER 7-DWG-22187-GC407.REVX ICRA PLAN - PHASE 3 - RISER 7 MULTICORELINK:DWG-22187-GC408.REVX ICRA PLAN - PHASE 3 - RISER 8-DWG-22187-GC408.REVX ICRA PLAN - PHASE 3 - RISER 8 MULTICORELINK:DWG-22187-GC408.REVX ICRA PLAN - PHASE 3 - RISER 8-DWG-22187-GC408.REVX ICRA PLAN - PHASE 3 - RISER 8 MULTICORELINK:DWG-22187-GC409.REVX ICRA PLAN - PHASE 3 - RISER 9-DWG-22187-GC409.REVX ICRA PLAN - PHASE 3 - RISER 9 MULTICORELINK:DWG-22187-GC409.REVX ICRA PLAN - PHASE 3 - RISER 9-DWG-22187-GC409.REVX ICRA PLAN - PHASE 3 - RISER 9 MULTICORELINK:DWG-22187-GC410.REVX ICRA PLAN - PHASE 3 - RISER 10-DWG-22187-GC410.REVX ICRA PLAN - PHASE 3 - RISER 10 MULTICORELINK:DWG-22187-GC410.REVX ICRA PLAN - PHASE 3 - RISER 10-DWG-22187-GC410.REVX ICRA PLAN - PHASE 3 - RISER 10 MULTICORELINK:DWG-22187-GC411.REVX ICRA PLAN - PHASE 3 - RISER 11-DWG-22187-GC411.REVX ICRA PLAN - PHASE 3 - RISER 11 MULTICORELINK:DWG-22187-GC411.REVX ICRA PLAN - PHASE 3 - RISER 11-DWG-22187-GC411.REVX ICRA PLAN - PHASE 3 - RISER 11 MULTICORELINK:DWG-22187-GC412.REVX ICRA PLAN - PHASE 3 - RISER 12-DWG-22187-GC412.REVX ICRA PLAN - PHASE 3 - RISER 12 MULTICORELINK:DWG-22187-GC412.REVX ICRA PLAN - PHASE 3 - RISER 12-DWG-22187-GC412.REVX ICRA PLAN - PHASE 3 - RISER 12 MULTICORELINK:DWG-22187-H-101-REV.X ABATEMENT DESIGN PLAN - BASEMENT-DWG-22187-H-101-REV.X ABATEMENT DESIGN PLAN - BASEMENT MULTICORELINK:DWG-22187-H-101-REV.X ABATEMENT DESIGN PLAN - BASEMENT-DWG-22187-H-101-REV.X ABATEMENT DESIGN PLAN - BASEMENT MULTICORELINK:DWG-22187-H-121-REV.X ABATEMENT DESIGN PLAN FIRST FLOOR-DWG-22187-H-121-REV.X ABATEMENT DESIGN PLAN FIRST FLOOR MULTICORELINK:DWG-22187-H-121-REV.X ABATEMENT DESIGN PLAN FIRST FLOOR-DWG-22187-H-121-REV.X ABATEMENT DESIGN PLAN FIRST FLOOR MULTICORELINK:DWG-22187-H-141-REV.X ABATEMENT DESIGN PLAN SECOND FLOOR-DWG-22187-H-141-REV.X ABATEMENT DESIGN PLAN SECOND FLOOR MULTICORELINK:DWG-22187-H-141-REV.X ABATEMENT DESIGN PLAN SECOND FLOOR-DWG-22187-H-141-REV.X ABATEMENT DESIGN PLAN SECOND FLOOR MULTICORELINK:DWG-22187-H-161-REV.X ABATEMENT DESIGN PLAN THIRD FLOOR-DWG-22187-H-161-REV.X ABATEMENT DESIGN PLAN THIRD FLOOR MULTICORELINK:DWG-22187-H-161-REV.X ABATEMENT DESIGN PLAN THIRD FLOOR-DWG-22187-H-161-REV.X ABATEMENT DESIGN PLAN THIRD FLOOR MULTICORELINK:DWG-22187-A-001.REVX ARCHITECTURAL NOTES & LEGENDS-DWG-22187-A-001.REVX ARCHITECTURAL NOTES & LEGENDS MULTICORELINK:DWG-22187-A-001.REVX ARCHITECTURAL NOTES & LEGENDS-DWG-22187-A-001.REVX ARCHITECTURAL NOTES & LEGENDS MULTICORELINK:DWG-22187-AD121.REVX ARCHITECTURAL DEMOLITION PLAN - FIRST FLOOR-DWG-22187-AD121.REVX ARCHITECTURAL DEMOLITION PLAN - FIRST FLOOR MULTICORELINK:DWG-22187-AD121.REVX ARCHITECTURAL DEMOLITION PLAN - FIRST FLOOR-DWG-22187-AD121.REVX ARCHITECTURAL DEMOLITION PLAN - FIRST FLOOR MULTICORELINK:DWG-22187-AD141.REVX ARCHITECTURAL DEMOLITION PLAN - SECOND FL-DWG-22187-AD141.REVX ARCHITECTURAL DEMOLITION PLAN - SECOND FL MULTICORELINK:DWG-22187-AD141.REVX ARCHITECTURAL DEMOLITION PLAN - SECOND FL-DWG-22187-AD141.REVX ARCHITECTURAL DEMOLITION PLAN - SECOND FL MULTICORELINK:DWG-22187-AD161.REVX ARCHITECTURAL DEMOLITION PLAN - THIRD FLOOR-DWG-22187-AD161.REVX ARCHITECTURAL DEMOLITION PLAN - THIRD FLOOR MULTICORELINK:DWG-22187-AD161.REVX ARCHITECTURAL DEMOLITION PLAN - THIRD FLOOR-DWG-22187-AD161.REVX ARCHITECTURAL DEMOLITION PLAN - THIRD FLOOR MULTICORELINK:DWG-22187-AE121.REVX ARCHITECTURAL PLAN - FIRST FLOOR-DWG-22187-AE121.REVX ARCHITECTURAL PLAN - FIRST FLOOR MULTICORELINK:DWG-22187-AE121.REVX ARCHITECTURAL PLAN - FIRST FLOOR-DWG-22187-AE121.REVX ARCHITECTURAL PLAN - FIRST FLOOR MULTICORELINK:DWG-22187-AE141.REVX ARCHITECTURAL PLAN - SECOND FLOOR-DWG-22187-AE141.REVX ARCHITECTURAL PLAN - SECOND FLOOR MULTICORELINK:DWG-22187-AE141.REVX ARCHITECTURAL PLAN - SECOND FLOOR-DWG-22187-AE141.REVX ARCHITECTURAL PLAN - SECOND FLOOR MULTICORELINK:DWG-22187-AE161.REVX ARCHITECTURAL PLAN - THIRD FLOOR-DWG-22187-AE161.REVX ARCHITECTURAL PLAN - THIRD FLOOR MULTICORELINK:DWG-22187-AE161.REVX ARCHITECTURAL PLAN - THIRD FLOOR-DWG-22187-AE161.REVX ARCHITECTURAL PLAN - THIRD FLOOR MULTICORELINK:DWG-22187-AE401.REVX ARCHITECTURAL ENLARGED PLAN - FIRST FLOOR-DWG-22187-AE401.REVX ARCHITECTURAL ENLARGED PLAN - FIRST FLOOR MULTICORELINK:DWG-22187-AE401.REVX ARCHITECTURAL ENLARGED PLAN - FIRST FLOOR-DWG-22187-AE401.REVX ARCHITECTURAL ENLARGED PLAN - FIRST FLOOR MULTICORELINK:DWG-22187-AE501.REVX ARCHITECTURAL WALL TYPES AND DETAILS-DWG-22187-AE501.REVX ARCHITECTURAL WALL TYPES AND DETAILS MULTICORELINK:DWG-22187-AE501.REVX ARCHITECTURAL WALL TYPES AND DETAILS-DWG-22187-AE501.REVX ARCHITECTURAL WALL TYPES AND DETAILS MULTICORELINK:DWG-22187-M-001.REVX MECHANICAL NOTES AND LEGEND-DWG-22187-M-001.REVX MECHANICAL NOTES AND LEGEND MULTICORELINK:DWG-22187-M-001.REVX MECHANICAL NOTES AND LEGEND-DWG-22187-M-001.REVX MECHANICAL NOTES AND LEGEND MULTICORELINK:DWG-22187-MD101.REVX MECHANICAL DEMOLITION PLAN - BASEMENT-DWG-22187-MD101.REVX MECHANICAL DEMOLITION PLAN - BASEMENT MULTICORELINK:DWG-22187-MD101.REVX MECHANICAL DEMOLITION PLAN - BASEMENT-DWG-22187-MD101.REVX MECHANICAL DEMOLITION PLAN - BASEMENT MULTICORELINK:DWG-22187-MD121.REVX MECHANICAL DEMOLITION PLAN - FIRST FLOOR-DWG-22187-MD121.REVX MECHANICAL DEMOLITION PLAN - FIRST FLOOR MULTICORELINK:DWG-22187-MD121.REVX MECHANICAL DEMOLITION PLAN - FIRST FLOOR-DWG-22187-MD121.REVX MECHANICAL DEMOLITION PLAN - FIRST FLOOR MULTICORELINK:DWG-22187-MD141.REVX MECHANICAL DEMOLITION PLAN - SECOND FLOOR-DWG-22187-MD141.REVX MECHANICAL DEMOLITION PLAN - SECOND FLOOR MULTICORELINK:DWG-22187-MD141.REVX MECHANICAL DEMOLITION PLAN - SECOND FLOOR-DWG-22187-MD141.REVX MECHANICAL DEMOLITION PLAN - SECOND FLOOR MULTICORELINK:DWG-22187-MD161.REVX MECHANICAL DEMOLITION PLAN - THIRD FLOOR-DWG-22187-MD161.REVX MECHANICAL DEMOLITION PLAN - THIRD FLOOR MULTICORELINK:DWG-22187-MD161.REVX MECHANICAL DEMOLITION PLAN - THIRD FLOOR-DWG-22187-MD161.REVX MECHANICAL DEMOLITION PLAN - THIRD FLOOR MULTICORELINK:DWG-22187-MD191.REVX MECHANICAL DEMOLITION PLAN - ROOF-PENTHOUSE-DWG-22187-MD191.REVX MECHANICAL DEMOLITION PLAN - ROOF-PENTHOUSE MULTICORELINK:DWG-22187-MD191.REVX MECHANICAL DEMOLITION PLAN - ROOF-PENTHOUSE-DWG-22187-MD191.REVX MECHANICAL DEMOLITION PLAN - ROOF-PENTHOUSE MULTICORELINK:DWG-22187-MD406.REVX MECHANICAL DEMO PLAN - ROOF-PENTHOUSE-DWG-22187-MD406.REVX MECHANICAL DEMO PLAN - ROOF-PENTHOUSE MULTICORELINK:DWG-22187-MD406.REVX MECHANICAL DEMO PLAN - ROOF-PENTHOUSE-DWG-22187-MD406.REVX MECHANICAL DEMO PLAN - ROOF-PENTHOUSE MULTICORELINK:DWG-22187-MH601.REVX MECHANICAL SCHEDULES-DWG-22187-MH601.REVX MECHANICAL SCHEDULES MULTICORELINK:DWG-22187-MH601.REVX MECHANICAL SCHEDULES-DWG-22187-MH601.REVX MECHANICAL SCHEDULES MULTICORELINK:DWG-22187-MH602.REVX MECHANICAL SCHEDULES-DWG-22187-MH602.REVX MECHANICAL SCHEDULES MULTICORELINK:DWG-22187-MH602.REVX MECHANICAL SCHEDULES-DWG-22187-MH602.REVX MECHANICAL SCHEDULES MULTICORELINK:DWG-22187-MI601.REVX MECHANICAL CONTROLS DIAGRAMS-DWG-22187-MI601.REVX MECHANICAL CONTROLS DIAGRAMS MULTICORELINK:DWG-22187-MI601.REVX MECHANICAL CONTROLS DIAGRAMS-DWG-22187-MI601.REVX MECHANICAL CONTROLS DIAGRAMS MULTICORELINK:DWG-22187-MI602.REVX MECHANICAL CONTROLS DIAGRAMS-DWG-22187-MI602.REVX MECHANICAL CONTROLS DIAGRAMS MULTICORELINK:DWG-22187-MI602.REVX MECHANICAL CONTROLS DIAGRAMS-DWG-22187-MI602.REVX MECHANICAL CONTROLS DIAGRAMS MULTICORELINK:DWG-22187-MP111.REVX MECHANICAL PIPING PLAN - BASEMENT CEILING-DWG-22187-MP111.REVX MECHANICAL PIPING PLAN - BASEMENT CEILING MULTICORELINK:DWG-22187-MP111.REVX MECHANICAL PIPING PLAN - BASEMENT CEILING-DWG-22187-MP111.REVX MECHANICAL PIPING PLAN - BASEMENT CEILING MULTICORELINK:DWG-22187-MP121.REVX MECHANICAL PIPING PLAN - FIRST FLOOR-DWG-22187-MP121.REVX MECHANICAL PIPING PLAN - FIRST FLOOR MULTICORELINK:DWG-22187-MP121.REVX MECHANICAL PIPING PLAN - FIRST FLOOR-DWG-22187-MP121.REVX MECHANICAL PIPING PLAN - FIRST FLOOR MULTICORELINK:DWG-22187-MP131.REVX MECHANICAL PIPING PLAN - FIRST FLOOR CEILING-DWG-22187-MP131.REVX MECHANICAL PIPING PLAN - 1ST FLOOR CEILING MULTICORELINK:DWG-22187-MP131.REVX MECHANICAL PIPING PLAN - FIRST FLOOR CEILING-DWG-22187-MP131.REVX MECHANICAL PIPING PLAN - 1ST FLOOR CEILING MULTICORELINK:DWG-22187-MP141.REVX MECHANICAL PIPING PLAN - SECOND FLOOR-DWG-22187-MP141.REVX MECHANICAL PIPING PLAN - SECOND FLOOR MULTICORELINK:DWG-22187-MP141.REVX MECHANICAL PIPING PLAN - SECOND FLOOR-DWG-22187-MP141.REVX MECHANICAL PIPING PLAN - SECOND FLOOR MULTICORELINK:DWG-22187-MP151.REVX MECHANICAL PIPING PLAN - SECOND FLOOR AT CEILING-DWG-22187-MP151.REVX MECHANICAL PIPING PLAN - 2ND FLOOR CEILING MULTICORELINK:DWG-22187-MP151.REVX MECHANICAL PIPING PLAN - SECOND FLOOR AT CEILING-DWG-22187-MP151.REVX MECHANICAL PIPING PLAN - 2ND FLOOR CEILING MULTICORELINK:DWG-22187-MP161.REVX MECHANICAL PIPING PLAN - THIRD FLOOR-DWG-22187-MP161.REVX MECHANICAL PIPING PLAN - THIRD FLOOR MULTICORELINK:DWG-22187-MP161.REVX MECHANICAL PIPING PLAN - THIRD FLOOR-DWG-22187-MP161.REVX MECHANICAL PIPING PLAN - THIRD FLOOR MULTICORELINK:DWG-22187-MP171.REVX MECHANICAL PIPING PLAN - THIRD FLOOR AT CEILING-DWG-22187-MP171.REVX MECHANICAL PIPING PLAN - 3RD FLOOR CEILING MULTICORELINK:DWG-22187-MP171.REVX MECHANICAL PIPING PLAN - THIRD FLOOR AT CEILING-DWG-22187-MP171.REVX MECHANICAL PIPING PLAN - 3RD FLOOR CEILING MULTICORELINK:DWG-22187-MP181.REVX MECHANICAL PIPING PLAN - ROOF-CRAWLSPACE-DWG-22187-MP181.REVX MECHANICAL PIPING PLAN - ROOF-CRAWLSPACE MULTICORELINK:DWG-22187-MP181.REVX MECHANICAL PIPING PLAN - ROOF-CRAWLSPACE-DWG-22187-MP181.REVX MECHANICAL PIPING PLAN - ROOF-CRAWLSPACE MULTICORELINK:DWG-22187-MP191.REVX MECHANICAL PIPING PLAN - ROOF-PENTHOUSE-DWG-22187-MP191.REVX MECHANICAL PIPING PLAN - ROOF-PENTHOUSE MULTICORELINK:DWG-22187-MP191.REVX MECHANICAL PIPING PLAN - ROOF-PENTHOUSE-DWG-22187-MP191.REVX MECHANICAL PIPING PLAN - ROOF-PENTHOUSE MULTICORELINK:DWG-22187-MP201.REVX MECHANICAL PIPING SCHEMATIC-ROOF-PENTHOUSE-DWG-22187-MP201.REVX MECHANICAL PIPING SCHEMATIC-ROOF-PENTHOUSE MULTICORELINK:DWG-22187-MP201.REVX MECHANICAL PIPING SCHEMATIC-ROOF-PENTHOUSE-DWG-22187-MP201.REVX MECHANICAL PIPING SCHEMATIC-ROOF-PENTHOUSE MULTICORELINK:DWG-22187-MP301.REVX MECHANICAL SECTIONS-DWG-22187-MP301.REVX MECHANICAL SECTIONS MULTICORELINK:DWG-22187-MP301.REVX MECHANICAL SECTIONS-DWG-22187-MP301.REVX MECHANICAL SECTIONS MULTICORELINK:DWG-22187-MP401.REVX MECHANICAL ENLARGED PIPING PLAN - ROOF PENTHOUSE-DWG-22187-MP401.REVX MECHANICAL ENLARGED PIPING PLAN - ROOF PENTHOUSE MULTICORELINK:DWG-22187-MP401.REVX MECHANICAL ENLARGED PIPING PLAN - ROOF PENTHOUSE-DWG-22187-MP401.REVX MECHANICAL ENLARGED PIPING PLAN - ROOF PENTHOUSE MULTICORELINK:DWG-22187-MP501.REVX MECHANICAL PIPING DETAILS-DWG-22187-MP501.REVX MECHANICAL PIPING DETAILS MULTICORELINK:DWG-22187-MP501.REVX MECHANICAL PIPING DETAILS-DWG-22187-MP501.REVX MECHANICAL PIPING DETAILS MULTICORELINK:DWG-22187-MP601.REVX MECHANICAL PIPING RISER - RF PENTHOUSE-DWG-22187-MP601.REVX MECHANICAL PIPING RISER - ROOF PENTHOUSE MULTICORELINK:DWG-22187-MP601.REVX MECHANICAL PIPING RISER - RF PENTHOUSE-DWG-22187-MP601.REVX MECHANICAL PIPING RISER - ROOF PENTHOUSE MULTICORELINK:DWG-22187-MP602.REVX MECHANICAL PIPING RISER-DWG-22187-MP602.REVX MECHANICAL PIPING RISER MULTICORELINK:DWG-22187-MP602.REVX MECHANICAL PIPING RISER-DWG-22187-MP602.REVX MECHANICAL PIPING RISER MULTICORELINK:DWG-22187-MP603.REVX MECHANICAL PIPING RISER-DWG-22187-MP603.REVX MECHANICAL PIPING RISER MULTICORELINK:DWG-22187-MP603.REVX MECHANICAL PIPING RISER-DWG-22187-MP603.REVX MECHANICAL PIPING RISER MULTICORELINK:DWG-22187-E-001-REVX ELECTRICAL NOTES AND LEGENDS-DWG-22187-E-001-REVX ELECTRICAL NOTES AND LEGENDS MULTICORELINK:DWG-22187-E-001-REVX ELECTRICAL NOTES AND LEGENDS-DWG-22187-E-001-REVX ELECTRICAL NOTES AND LEGENDS MULTICORELINK:DWG-22187-ED101-REVX ELECTRICAL DEMOLITION PLAN - BASEMENT-DWG-22187-ED101-REVX ELECTRICAL DEMOLITION PLAN - BASEMENT MULTICORELINK:DWG-22187-ED101-REVX ELECTRICAL DEMOLITION PLAN - BASEMENT-DWG-22187-ED101-REVX ELECTRICAL DEMOLITION PLAN - BASEMENT MULTICORELINK:DWG-22187-ED121-REVX ELECTRICAL DEMOLITION PLAN - FIRST FLOOR-DWG-22187-ED121-REVX ELECTRICAL DEMOLITION PLAN - FIRST FLOOR MULTICORELINK:DWG-22187-ED121-REVX ELECTRICAL DEMOLITION PLAN - FIRST FLOOR-DWG-22187-ED121-REVX ELECTRICAL DEMOLITION PLAN - FIRST FLOOR MULTICORELINK:DWG-22187-ED141-REVX ELECTRICAL DEMOLITION PLAN - SECOND FLOOR-DWG-22187-ED141-REVX ELECTRICAL DEMOLITION PLAN - SECOND FLOOR MULTICORELINK:DWG-22187-ED141-REVX ELECTRICAL DEMOLITION PLAN - SECOND FLOOR-DWG-22187-ED141-REVX ELECTRICAL DEMOLITION PLAN - SECOND FLOOR MULTICORELINK:DWG-22187-ED161-REVX ELECTRICAL DEMOLITION PLAN - THIRD FLOOR-DWG-22187-ED161-REVX ELECTRICAL DEMOLITION PLAN - THIRD FLOOR MULTICORELINK:DWG-22187-ED161-REVX ELECTRICAL DEMOLITION PLAN - THIRD FLOOR-DWG-22187-ED161-REVX ELECTRICAL DEMOLITION PLAN - THIRD FLOOR MULTICORELINK:DWG-22187-ED191-REVX ELECTRICAL DEMOLITION PLAN - PENTHOUSE-DWG-22187-ED191-REVX ELECTRICAL DEMOLITION PLAN - PENTHOUSE MULTICORELINK:DWG-22187-ED191-REVX ELECTRICAL DEMOLITION PLAN - PENTHOUSE-DWG-22187-ED191-REVX ELECTRICAL DEMOLITION PLAN - PENTHOUSE MULTICORELINK:DWG-22187-EP101-REVX ELECTRICAL POWER PLAN - BASEMENT-DWG-22187-EP101-REVX ELECTRICAL POWER PLAN - BASEMENT MULTICORELINK:DWG-22187-EP101-REVX ELECTRICAL POWER PLAN - BASEMENT-DWG-22187-EP101-REVX ELECTRICAL POWER PLAN - BASEMENT MULTICORELINK:DWG-22187-EP121-REVX ELECTRICAL POWER PLAN - FIRST FLOOR-DWG-22187-EP121-REVX ELECTRICAL POWER PLAN - FIRST FLOOR MULTICORELINK:DWG-22187-EP121-REVX ELECTRICAL POWER PLAN - FIRST FLOOR-DWG-22187-EP121-REVX ELECTRICAL POWER PLAN - FIRST FLOOR MULTICORELINK:DWG-22187-EP141-REVX ELECTRICAL POWER PLAN - SECOND FLOOR-DWG-22187-EP141-REVX ELECTRICAL POWER PLAN - SECOND FLOOR MULTICORELINK:DWG-22187-EP141-REVX ELECTRICAL POWER PLAN - SECOND FLOOR-DWG-22187-EP141-REVX ELECTRICAL POWER PLAN - SECOND FLOOR MULTICORELINK:DWG-22187-EP161-REVX ELECTRICAL POWER PLAN - THIRD FLOOR-DWG-22187-EP161-REVX ELECTRICAL POWER PLAN - THIRD FLOOR MULTICORELINK:DWG-22187-EP161-REVX ELECTRICAL POWER PLAN - THIRD FLOOR-DWG-22187-EP161-REVX ELECTRICAL POWER PLAN - THIRD FLOOR MULTICORELINK:DWG-22187-EP191-REVX ELECTRICAL POWER PLAN - PENTHOUSE-DWG-22187-EP191-REVX ELECTRICAL POWER PLAN - PENTHOUSE MULTICORELINK:DWG-22187-EP191-REVX ELECTRICAL POWER PLAN - PENTHOUSE-DWG-22187-EP191-REVX ELECTRICAL POWER PLAN - PENTHOUSE AutoCAD SHX Text one eighth inch = one foot
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text three inches = one foot
AutoCAD SHX Text 6"
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text 6"
AutoCAD SHX Text one and one half inches = one foot
AutoCAD SHX Text one inch = one foot
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text 6"
AutoCAD SHX Text 6"
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text three quarters inch = one foot
AutoCAD SHX Text one half inch = one foot
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text three eighths inch = one foot
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text one quarter inch = one foot
AutoCAD SHX Text
DRAWING INDEX
AutoCAD SHX Text DEPARTMENT OF VETERANS AFFAIRS PROJECT NO. 620A4-22-101 41 CASTLE POINT RD. WAPPINGERS FALLS, NY
AutoCAD SHX Text
SCALE: NONE
AutoCAD SHX Text
SITE PLAN
AutoCAD SHX Text
SCALE: NONE
AutoCAD SHX Text
SITE LOCATION
B
A
PENTHOUSE 03
ELEV. MECH.
ROOM
CENTER
STAIR HALL
PENTHOUSE 02 -
ROOF
P-2
P-1
1.1
Project Number
Building Number
Drawing Number
Project Title
Location
Issue Date Checked Drawn
Drawing Title
Approved:
VA FORM 08 - 6231
A
Office of Construction and Facilities Management
U.S. Department of Veterans Affairs
B
C
D
E
F
A
B
C
D
E
F
21 4 5 6 7 8 9 10
PhaseARCHITECT/ENGINEER OF RECORDCONSULTANT
321 4 5 6 7 8 9 10
Project Director
Revisions: Date:
GENERAL PHASING PLAN -
ROOF-PENTHOUSE
CONTRACT DOCUMENTS
FULLY SPRINKLERED
REPLACE FAN COIL UNITS, BLDG 18
41 CASTLE POINT RD.
WAPPINGERS FALLS, NY 12590
2024-12-10
GC101
620A4-22-101
DJU IJS
REV 0 CONTRACT DOCUMENTS 2024/12/10
"Unauthorized alteration or addition to any plans, specifications or reports bearing a Licensed Professional Engineer's seal is a violation of Section 7209, subdivision 2, of the New York State Education Law".
CERTIFICATE OF AUTHORIZATION NUMBER: 0020000
SCALE: 1/8" = 1'-0"
GENERAL PHASING PLAN - ROOF/PENTHOUSE1
N
GENERAL NOTES
1. PHASING IS DESIGNATED THROUGHOUT THE DRAWING SET VIA
2.
CONTRACTOR SHALL BE RESPONSIBLE FOR ALL WORK AREA AND LAY DOWN FENCING AREAS.
MAINTAIN SAFE AND CLEAN CONDITIONS THROUGHOUT DURATION OF PROJECT. COORDINATE
FINAL LOCATION/LAYOUT/DIMENSIONS WITH VA FOR FINAL APPROVAL.
3.
PHASING NOTES INDICATE GENERAL WORK ITEMS TO BE PERFORMED. PHASE NOTES DO NOT
IMPLY SEQUENCE OF OPERATION. CONTRACTOR IS RESPONSIBLE FOR CREATING
CONSTRUCTION SCHEDULE AND COORDINATION OF SCHEDULE AMONGST TRADES.
4.
WORK OUTSIDE THE DESIGNATED PHASE AREA MAY BE REQUIRED TO COMPLETE PHASED
WORK. CONTRACTOR IS TO COORDINATE ALL WORK WITH COR AND BETWEEN ANY AND ALL
SUBCONTRACTORS TO ENSURE CONTINUED OPERATIONS AND INTENT SHOWN THROUGHOUT
THIS DRAWING SET.
5. REFER TO SPECIFICATION 010000 GENERAL REQUIREMENTS FOR ADDITIONAL PHASING
INFORMATION.
6. REFER TO H-SERIES DRAWINGS FOR HAZARDOUS MATERIAL REQUIREMENTS
7. EXCECUTE WORK BY METHODS TO MINIMIZE RAISING DUST.
8. IMMEDIATELY REPLACE CEILING TILE IF DISPLACED.
9. PROVIDE ACTIVE MEANS TO PREVENT AIRBORNE DUST FROM DISPERSING INTO ATMOSPHERE.
10. WATER-MIST WORK SURFACES TO CONTROL DUST WHILE CUTTING.
11. SEAL UNUSED DOORS WITH DUCT TAPE
12. ISOLATE HVAC SYSTEM IN AREAS WHERE WORK IS BEING PERFORMED TO PREVENT
CONTAMINATION OF DUCT SYSTEM.
13. PLACE DUST MAT AT ENTRANCE AND EXIT OF WORK AREA.
14. COVER CONSTRUCTION WASTE BEFORE TRANSPORT IN COVERED CONTAINERS.
15. WET MOP AND/OR VACUUM WITH HEPA FILTERED VACUUM BEFORE LEAVING WORK AREA.
16. OPEN PREVIOUSLY SEALED HVAC REGISTERS AND GRILLS.
17. HOUSEKEEPING TO WIPE WORK SURFACES AND FLOORS WITH DISINFECTANT.
18. ALL PENETRATIONS THROUGH FLOORS AND/OR RATED WALLS SHALL BE FIRE SEALED PRIOR
TO THE END OF EACH SHIFT.
PHASE NOTES
1. REMOVE PUMPS, HEAT EXCHANGER AND PIPING
2. INSTALL NEW PUMPS, HEAT EXCHANGER, AND TIE IN TO STEAM AND CHILLED WATER
PHASE & RISER SCHEDULE
PHASE # RISER ASSOCIATED
1.1 PENTHOUSE
2.1 PENTHOUSE
2.2 CRAWLSPACE (1 THRU 12)
3.1 1
3.2 3
3.3 2
3.4 12
3.5 8
3.6 9, 10
3.7 11
3.8 7
3.9 6
3.10 5
3.11 4
15H 15E
17G 18D
16F
111 19C
20B
75A
21A
73A
59A
N
Exp. 11/30/2027
23 Mechanic Street, Springville, NY 14141
12/10/2024
AutoCAD SHX Text one eighth inch = one foot
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text three inches = one foot
AutoCAD SHX Text 6"
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text 6"
AutoCAD SHX Text one and one half inches = one foot
AutoCAD SHX Text one inch = one foot
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text 6"
AutoCAD SHX Text 6"
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text three quarters inch = one foot
AutoCAD SHX Text one half inch = one foot
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text three eighths inch = one foot
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text one quarter inch = one foot
A
PENTHOUSE 03
ELEV. MECH.
ROOM
CENTER
STAIR HALL
PENTHOUSE 02 -
ROOF
P-2
P-1
■■ 7
2 8
2.2
2.1
Project Number
Building Number
Drawing Number
Project Title
Location
Issue Date Checked Drawn
Drawing Title
Approved:
VA FORM 08 - 6231
A
Office of Construction and Facilities Management
U.S. Department of Veterans Affairs
B
C
D
E
F
A
B
C
D
E
F
21 4 5 6 7 8 9 10
PhaseARCHITECT/ENGINEER OF RECORDCONSULTANT
321 4 5 6 7 8 9 10
Project Director
Revisions: Date:
GENERAL PHASING PLAN -
ROOF-CRAWLSPACE
CONTRACT DOCUMENTS
FULLY SPRINKLERED
REPLACE FAN COIL UNITS, BLDG 18
41 CASTLE POINT RD.
WAPPINGERS FALLS, NY 12590
2024-12-10
GC102
620A4-22-101
DJU IJS
REV 0 CONTRACT DOCUMENTS 2024/12/10
"Unauthorized alteration or addition to any plans, specifications or reports bearing a Licensed Professional Engineer's seal is a violation of Section 7209, subdivision 2, of the New York State Education Law".
CERTIFICATE OF AUTHORIZATION NUMBER: 0020000
SCALE: 1/8" = 1'-0"
GENERAL PHASING PLAN - ROOF/CRAWLSPACE1
N
GENERAL NOTES
1. PHASING IS DESIGNATED THROUGHOUT THE DRAWING SET VIA
2.
CONTRACTOR SHALL BE RESPONSIBLE FOR ALL WORK AREA AND LAY DOWN FENCING AREAS.
MAINTAIN SAFE AND CLEAN CONDITIONS THROUGHOUT DURATION OF PROJECT. COORDINATE
FINAL LOCATION/LAYOUT/DIMENSIONS WITH VA FOR FINAL APPROVAL.
3.
PHASING NOTES INDICATE GENERAL WORK ITEMS TO BE PERFORMED. PHASE NOTES DO NOT
IMPLY SEQUENCE OF OPERATION. CONTRACTOR IS RESPONSIBLE FOR CREATING
CONSTRUCTION SCHEDULE AND COORDINATION OF SCHEDULE AMONGST TRADES.
4.
WORK OUTSIDE THE DESIGNATED PHASE AREA MAY BE REQUIRED TO COMPLETE PHASED
WORK. CONTRACTOR IS TO COORDINATE ALL WORK WITH COR AND BETWEEN ANY AND ALL
SUBCONTRACTORS TO ENSURE CONTINUED OPERATIONS AND INTENT SHOWN THROUGHOUT
THIS DRAWING SET.
5. REFER TO SPECIFICATION 010000 GENERAL REQUIREMENTS FOR ADDITIONAL PHASING
INFORMATION.
6. REFER TO H-SERIES DRAWINGS FOR HAZARDOUS MATERIAL REQUIREMENTS
7. EXCECUTE WORK BY METHODS TO MINIMIZE RAISING DUST.
8. IMMEDIATELY REPLACE CEILING TILE IF DISPLACED.
9. PROVIDE ACTIVE MEANS TO PREVENT AIRBORNE DUST FROM DISPERSING INTO ATMOSPHERE.
10. WATER-MIST WORK SURFACES TO CONTROL DUST WHILE CUTTING.
11. SEAL UNUSED DOORS WITH DUCT TAPE
12. ISOLATE HVAC SYSTEM IN AREAS WHERE WORK IS BEING PERFORMED TO PREVENT
CONTAMINATION OF DUCT SYSTEM.
13. PLACE DUST MAT AT ENTRANCE AND EXIT OF WORK AREA.
14. COVER CONSTRUCTION WASTE BEFORE TRANSPORT IN COVERED CONTAINERS.
15. WET MOP AND/OR VACUUM WITH HEPA FILTERED VACUUM BEFORE LEAVING WORK AREA.
16. OPEN PREVIOUSLY SEALED HVAC REGISTERS AND GRILLS.
17. HOUSEKEEPING TO WIPE WORK SURFACES AND FLOORS WITH DISINFECTANT.
18. ALL PENETRATIONS THROUGH FLOORS AND/OR RATED WALLS SHALL BE FIRE SEALED PRIOR
TO THE END OF EACH SHIFT.
PHASE NOTES
1. PERFORM ROUTING OF NEW 4 PIPE DISTRIBUTION PARALLEL TO EXISTING.
PHASE & RISER SCHEDULE
PHASE # RISER ASSOCIATED
1.1 PENTHOUSE
2.1 PENTHOUSE
2.2 CRAWLSPACE (1 THRU 12)
3.1 1
3.2 3
3.3 2
3.4 12
3.5 8
3.6 9, 10
3.7 11
3.8 7
3.9 6
3.10 5
3.11 4
15H 15E
17G 18D
16F
111 19C
20B
75A
21A
73A
59A
N
Exp. 11/30/2027
23 Mechanic Street, Springville, NY 14141
12/10/2024
AutoCAD SHX Text one eighth inch = one foot
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text three inches = one foot
AutoCAD SHX Text 6"
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text 6"
AutoCAD SHX Text one and one half inches = one foot
AutoCAD SHX Text one inch = one foot
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text 6"
AutoCAD SHX Text 6"
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text three quarters inch = one foot
AutoCAD SHX Text one half inch = one foot
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text three eighths inch = one foot
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
A
ELEVATOR
CLEAN
PREPARATION
SCOPE
PROCESS
WASHER
DECONTAMINATION
CART AUTO.
WASH
SCOPE
DECON.
ANTE RM. 03
ANTE RM. 04
H.A.C.
FEMALE
LOCKER
MALE
LOCKER 17
MALE
BATH.
FEMALE
BATH.
STERILE/
NON-STERILE
STERILIZERS
ANTE RM. 02 32
CLEAN
STORAGE
ENTRY
CHIEF OFFICE
SYSTEMS RM.
TECH. OFFICE
ANTE RM. 01
H.A.C.
MALE
BATH.
FEMALE
LOCKER 39
O.I.F.
OFFICE
FEMALE
TOILET
MALE
TOILET
CORRIDOR 1 017
MECHANICAL
RM.
TOILET
CORRIDOR 2
- (008)
VEST. 01
- (008A)
VEST. 02
CENTER
STAIR HALL
EMERGENCY POWER
ELEC RM
001H
ELEC RM
001I
OFFICE C
001J
OFFICE B
001N.3
EQUIP STOR001N.2
OFFICE A
001H.1
STORAGE
001F
ULTRASOUND 1
001K
R/F ROOM
001N.4
STAFF
TOILET
001K.1
TOILET
001L
SOILED
UTILITY
WAITING
001M
RADIOLOGY
001N.5
RECEPTION
001F.1
TOILET
001E.1
TOILET
001E
ULTRASOUND 2
001D
CLEAN
UTILITY
001C
TOUCHDOWN
SPACE
001B
BONE
DENSITOMETRY
001A
ULTRASOUND 3
C001
CORRIDOR
001A.1
TOILET
001N.1
STORAGE
TOILET
001N
WORK AREA
001G
STAIR
HALL 03
ELEC
DISTRIB
45678910 3 2 1
11109
12 3.6 3.7
3.10
3.9
3.4
3.5
3.8
3.11
Project Number
Building Number
Drawing Number
Project Title
Location
Issue Date Checked Drawn
Drawing Title
Approved:
VA FORM 08 - 6231
A
Office of Construction and Facilities Management
U.S. Department of Veterans Affairs
B
C
D
E
F
A
B
C
D
E
F
21 4 5 6 7 8 9 10
PhaseARCHITECT/ENGINEER OF RECORDCONSULTANT
321 4 5 6 7 8 9 10
Project Director
Revisions: Date:
GENERAL PHASING PLAN -
BASEMENT FLOOR
CONTRACT DOCUMENTS
FULLY SPRINKLERED
REPLACE FAN COIL UNITS, BLDG 18
41 CASTLE POINT RD.
WAPPINGERS FALLS, NY 12590
2024-12-10
GC103
620A4-22-101
DJU IJS
REV 0 CONTRACT DOCUMENTS 2024/12/10
"Unauthorized alteration or addition to any plans, specifications or reports bearing a Licensed Professional Engineer's seal is a violation of Section 7209, subdivision 2, of the New York State Education Law".
CERTIFICATE OF AUTHORIZATION NUMBER: 0020000
SCALE: 1/8" = 1'-0"
GENERAL PHASING PLAN - BASEMENT FLOOR1
N
GENERAL NOTES
1. PHASING IS DESIGNATED THROUGHOUT THE DRAWING SET VIA
2.
CONTRACTOR SHALL BE RESPONSIBLE FOR ALL WORK AREA AND LAY DOWN FENCING AREAS.
MAINTAIN SAFE AND CLEAN CONDITIONS THROUGHOUT DURATION OF PROJECT. COORDINATE
FINAL LOCATION/LAYOUT/DIMENSIONS WITH VA FOR FINAL APPROVAL.
3.
PHASING NOTES INDICATE GENERAL WORK ITEMS TO BE PERFORMED. PHASE NOTES DO NOT
IMPLY SEQUENCE OF OPERATION. CONTRACTOR IS RESPONSIBLE FOR CREATING
CONSTRUCTION SCHEDULE AND COORDINATION OF SCHEDULE AMONGST TRADES.
4.
WORK OUTSIDE THE DESIGNATED PHASE AREA MAY BE REQUIRED TO COMPLETE PHASED
WORK. CONTRACTOR IS TO COORDINATE ALL WORK WITH COR AND BETWEEN ANY AND ALL
SUBCONTRACTORS TO ENSURE CONTINUED OPERATIONS AND INTENT SHOWN THROUGHOUT
THIS DRAWING SET.
5. REFER TO SPECIFICATION 010000 GENERAL REQUIREMENTS FOR ADDITIONAL PHASING
INFORMATION.
6. REFER TO H-SERIES DRAWINGS FOR HAZARDOUS MATERIAL REQUIREMENTS
7.
INSTALL PLASTIC DUST BARRIERS TO SEAL AREA FROM NON-WORK AREA OR IMPLEMENT
CONTROL CUBE METHOD (CART WITH PLASTIC COVERING AND SEALED CONNECTION TO WORK
SITE WITH HEPA VACUUM FOR VACUUMING PRIOR TO EXIT) BEFORE CONSTRUCTION BEGINS.
8.
WHERE CEILING TILES ARE TO REMAIN DISPLACED FOR LONGER THAN A SINGLE SHIFT,
CONTRACTOR SHALL PROVIDED UL APPROVED 1-HOUR RATED CONSTRUCTION BARRIERS FOR
THAT WORK AREA.
9. ISOLATE HVAC SYSTEM IN AREAS WHERE WORK IS BEING PERFORMED TO PREVENT
CONTAMINATION OF DUCT SYSTEM.
10. MAINTAIN NEGATIVE PRESSURE WITHIN WORK SITE UTILIZING HEPA EQUIPPED AIR FILTRATION
UNITS.
11. PLACE DUST MAT AT ENTRANCE AND EXIT OF WORK AREA.
12. COVER CONSTRUCTION WASTE BEFORE TRANSPORT IN COVERED CONTAINERS.
13. ALL WORK ASSOCIATED WITH A MAJOR PROJECT THAT HAS AN APPROVED ICRA
AUTHORIZATION FORM WILL BE ASSESSED ON AN INDIVIDUAL BASIS.
14. WET MOP AND VACUUM WITH HEPA FILTER VACUUM BEFORE LEAVING WORK AREA.
15. DO NOT REMOVE BARRIES FROM WORK AREA UNTIL A HEALTH SYSTEM RESPONSIBLE PERSON
INSPECTS COMPLETED PROJECT.
16. REMOVE BARRIER MATERIALS CAREFULLY TO MINIMIZE SPREAD OF DIRT AND DEBRIS
ASSOCIATED WITH CONSTRUCTION.
17. REMOVE ISOLATION OF HVAC SYSTEM IN AREAS WHERE WORK WAS BEING PERFORMED.
18. HOUSEKEEPING TO WIPE WORK SURFACES AND FLOORS WITH DISINFECTANT.
19. ALL PENETRATIONS THROUGH FLOORS AND/OR RATED WALLS SHALL BE FIRE SEALED PRIOR
TO THE END OF EACH SHIFT.
PHASE NOTES
1. REMOVE FCUS, DISTRIBUTION PIPING AND RISE PIPING UP TO FLOOR ABOVE.
2. INSTALL NEW PIPING AND FCUS.
3. REPAIR PIPING CHASE.
PHASE & RISER SCHEDULE
PHASE # RISER ASSOCIATED
1.1 PENTHOUSE
2.1 PENTHOUSE
2.2 CRAWLSPACE (1 THRU 12)
3.1 1
3.2 3
3.3 2
3.4 12
3.5 8
3.6 9, 10
3.7 11
3.8 7
3.9 6
3.10 5
3.11 4
15H 15E
17G 18D
16F
111 19C
20B
75A
21A
73A
59A
N
Exp. 11/30/2027
23 Mechanic Street, Springville, NY 14141
12/10/2024
AutoCAD SHX Text one eighth inch = one foot
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text three inches = one foot
AutoCAD SHX Text 6"
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text 6"
AutoCAD SHX Text one and one half inches = one foot
AutoCAD SHX Text one inch = one foot
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text 6"
AutoCAD SHX Text 6"
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text three quarters inch = one foot
AutoCAD SHX Text one half inch = one foot
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text three eighths inch = one foot
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
ELEVATOR
ROOF
CONNECTING
CORRIDOR
B
5678910 3 2 1
A
EXAM
ROOM
OFFICE
EXAM
ROOM
ANTE
CORRIDOR
WEST
STAIR HALL
EXAM
ROOM
TOILET
ANTE
CORRIDOR
EXAM
ROOM
OFFICE
SOCIAL WORKER
OFFICE
SUPPLY
CLOSET
NUTRITION
CLINIC
WAITING
AREA
CENTER
STAIR HALL
CHECK-IN
RECEPTION 02
PROVIDER
SOCIAL WORKER
OFFICE
STORAGE
ROOM
CONFERENCE
ROOM
STOCK
ROOM -
EAST
STAIR HALL
STAFF
LOUNGE
PROVIDER
WAITING
ROOM
PATIENT
EDUCATION
E.M.S.
CLOSET
TOILET
DATA
CLOSET
SPRINKLER
CLOSET
WAITING
AREA
144A
TOILET
ANTE
CORRIDOR
148A
BATHROOM
OFFICE
OFFICE
OFFICE
OFFICE 138
OFFICE
OFFICE
OFFICE144
EXAM
ROOM
EXAM
ROOM
EXAM
ROOM
TOILET
ANTE
CORRIDOR
CORRIDOR 03 132
CORRIDOR 01
CORRIDOR 03
CORRIDOR 05
OFFICE
OFFICE
OFFICE 101
OFFICE
OFFICE
OFFICE
OFFICE
EXAM
ROOM 104
EXAM
ROOM
EXAM
ROOM125
EXAM
ROOM131
OFFICE
CORRIDOR 02
RECEPTION 02
ANTE
CORRIDOR 120
ANTE
CORRIDOR
ANTE
CORRIDOR 109
ANTE
CORRIDOR
CORRIDOR 06
TOILET
TOILET
CCC
2 8
3.43.33.1
3.5
3.6 3.7 3.8
3.2
3.10
3.9
3.11
Project Number
Building Number
Drawing Number
Project Title
Location
Issue Date Checked Drawn
Drawing Title
Approved:
VA FORM 08 - 6231
A
Office of Construction and Facilities Management
U.S. Department of Veterans Affairs
B
C
D
E
F
A
B
C
D
E
F
21 4 5 6 7 8 9 10
PhaseARCHITECT/ENGINEER OF RECORDCONSULTANT
321 4 5 6 7 8 9 10
Project Director
Revisions: Date:
GENERAL PHASING PLAN - FIRST
FLOOR
CONTRACT DOCUMENTS
FULLY SPRINKLERED
REPLACE FAN COIL UNITS, BLDG 18
41 CASTLE POINT RD.
WAPPINGERS FALLS, NY 12590
2024-12-10
GC104
620A4-22-101
DJU IJS
REV 0 CONTRACT DOCUMENTS 2024/12/10
"Unauthorized alteration or addition to any plans, specifications or reports bearing a Licensed Professional Engineer's seal is a violation of Section 7209, subdivision 2, of the New York State Education Law".
CERTIFICATE OF AUTHORIZATION NUMBER: 0020000
SCALE: 1/8" = 1'-0"
GENERAL PHASING PLAN - FIRST FLOOR1
N
GENERAL NOTES
1. PHASING IS DESIGNATED THROUGHOUT THE DRAWING SET VIA
2.
CONTRACTOR SHALL BE RESPONSIBLE FOR ALL WORK AREA AND LAY DOWN FENCING AREAS.
MAINTAIN SAFE AND CLEAN CONDITIONS THROUGHOUT DURATION OF PROJECT. COORDINATE
FINAL LOCATION/LAYOUT/DIMENSIONS WITH VA FOR FINAL APPROVAL.
3.
PHASING NOTES INDICATE GENERAL WORK ITEMS TO BE PERFORMED. PHASE NOTES DO NOT
IMPLY SEQUENCE OF OPERATION. CONTRACTOR IS RESPONSIBLE FOR CREATING
CONSTRUCTION SCHEDULE AND COORDINATION OF SCHEDULE AMONGST TRADES.
4.
WORK OUTSIDE THE DESIGNATED PHASE AREA MAY BE REQUIRED TO COMPLETE PHASED
WORK. CONTRACTOR IS TO COORDINATE ALL WORK WITH COR AND BETWEEN ANY AND ALL
SUBCONTRACTORS TO ENSURE CONTINUED OPERATIONS AND INTENT SHOWN THROUGHOUT
THIS DRAWING SET.
5. REFER TO SPECIFICATION 010000 GENERAL REQUIREMENTS FOR ADDITIONAL PHASING
INFORMATION.
6. REFER TO H-SERIES DRAWINGS FOR HAZARDOUS MATERIAL REQUIREMENTS
7.
INSTALL PLASTIC DUST BARRIERS TO SEAL AREA FROM NON-WORK AREA OR IMPLEMENT
CONTROL CUBE METHOD (CART WITH PLASTIC COVERING AND SEALED CONNECTION TO WORK
SITE WITH HEPA VACUUM FOR VACUUMING PRIOR TO EXIT) BEFORE CONSTRUCTION BEGINS.
8.
WHERE CEILING TILES ARE TO REMAIN DISPLACED FOR LONGER THAN A SINGLE SHIFT,
CONTRACTOR SHALL PROVIDE UL APPROVED 1-HOUR RATED CONSTRUCTION BARRIERS FOR
THAT WORK AREA
9. ISOLATE HVAC SYSTEM IN AREAS WHERE WORK IS BEING PERFORMED TO PREVENT
CONTAMINATION OF DUCT SYSTEM.
10. MAINTAIN NEGATIVE PRESSURE WITHIN WORK SITE UTILIZING HEPA EQUIPPED AIR FILTRATION
UNITS.
11. PLACE DUST MAT AT ENTRANCE AND EXIT OF WORK AREA.
12. COVER CONSTRUCTION WASTE BEFORE TRANSPORT IN COVERED CONTAINERS.
13. ALL WORK ASSOCIATED WITH A MAJOR PROJECT THAT HAS AN APPROVED ICRA
AUTHORIZATION FORM WILL BE ASSESSED ON AN INDIVIDUAL BASIS.
14. WET MOP AND VACUUM WITH HEPA FILTER VACUUM BEFORE LEAVING WORK AREA.
15. DO NOT REMOVE BARRIES FROM WORK AREA UNTIL A HEALTH SYSTEM RESPONSIBLE PERSON
INSPECTS COMPLETED PROJECT.
16. REMOVE BARRIER MATERIALS CAREFULLY TO MINIMIZE SPREAD OF DIRT AND DEBRIS
ASSOCIATED WITH CONSTRUCTION.
17. REMOVE ISOLATION OF HVAC SYSTEM IN AREAS WHERE WORK WAS BEING PERFORMED.
18. HOUSEKEEPING TO WIPE WORK SURFACES AND FLOORS WITH DISINFECTANT.
19. ALL PENETRATIONS THROUGH FLOORS AND/OR RATED WALLS SHALL BE FIRE SEALED PRIOR
TO THE END OF EACH SHIFT.
PHASE NOTES
1. REMOVE FCUS, DISTRIBUTION PIPING AND RISE PIPING UP TO FLOOR ABOVE.
2. INSTALL NEW PIPING AND FCUS.
3. REPAIR PIPING CHASE.
PHASE & RISER SCHEDULE
PHASE # RISER ASSOCIATED
1.1 PENTHOUSE
2.1 PENTHOUSE
2.2 CRAWLSPACE (1 THRU 12)
3.1 1
3.2 3
3.3 2
3.4 12
3.5 8
3.6 9, 10
3.7 11
3.8 7
3.9 6
3.10 5
3.11 4
15H 15E
17G 18D
16F
111 19C
20B
75A
21A
73A
59A
N
Exp. 11/30/2027
23 Mechanic Street, Springville, NY 14141
12/10/2024
AutoCAD SHX Text one eighth inch = one foot
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text three inches = one foot
AutoCAD SHX Text 6"
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text 6"
AutoCAD SHX Text one and one half inches = one foot
AutoCAD SHX Text one inch = one foot
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text 6"
AutoCAD SHX Text 6"
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text three quarters inch = one foot
AutoCAD SHX Text one half inch = one foot
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text three eighths inch = one foot
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
5678910 3 2 1
A
EXAM
ROOM
EXAM
ROOM
OFFICE
OFFICE
OFFICE
OFFICE
OFFICE222
OFFICE
223B2
OFFICE
TOILET
214C
TOILETS
208A
TOILET
206A
TOILET
207A
TOILET
211A
TOILET
223U4A
WOMENS
TOILET
EXAM
ROOM
EAST
STAIR HALL
JEFFERSON
CONFERENCE RM.
212B
ACCU. 01
208D
ACCU. 02
212A
ACCUPUNCTURE
CLINIC
WELLNESS
CLINIC
215B
SCHEDULING
WAITING
ROOM
OFFICE
214B
SHOWER
ROOM
UTILITY
ROOM
214A
SHOWER
ROOM
ENTRY
212C
BREAK
215A
CLOSET
E.M.S.
CLOSET
CORRIDOR 03
CORRIDOR 04
CORRIDOR 01
223B
RECEPTION
223A
WAITING
ROOM
223B1
STORAGE
223B3
ANTE
223C
DARK
ROOM
223D
PANORAMIC
X-RAY
223E
OPERATORY
#02
223F
OPERATORY
#01223G
OPERATORY
#03
223H
OFFICE
223I
OPERATORY
#04
223J
OPERATORY
#05
223K
OPERATORY
#06
223L
OPERATORY
#07
223M
OPERATORY
#08
CORRIDOR 02223V1
CORRIDOR 05
223V2
CORRIDOR 06
223V3
CORRIDOR 07
DENTAL ENTRY
WEST
STAIR HALL
223R1
RESIN CAST.
223Q
MECH. CL.
223R
LAB.
223U1
BREAK
ROOM
223U5A
CL.
223O
CL.
223N
CL.
223T
CL.223P
CORRIDOR 08
223S
INSTR.
PREP
223U2
CL.
223U
ANTE
223U5A
MENS
TOILET
223U5
MENS
LOCKER
223U4
WOMENS
LOCKER
223U3
CONFERENCE
ROOM
CENTER
STAIR HALL CC
C
1110912
3.43.33.1 3.5 3.6 3.7 3.8
3.2
3.10
3.9
3.11
Project Number
Building Number
Drawing Number
Project Title
Location
Issue Date Checked Drawn
Drawing Title
Approved:
VA FORM 08 - 6231
A
Office of Construction and Facilities Management
U.S. Department of Veterans Affairs
B
C
D
E
F
A
B
C
D
E
F
21 4 5 6 7 8 9 10
PhaseARCHITECT/ENGINEER OF RECORDCONSULTANT
321 4 5 6 7 8 9 10
Project Director
Revisions: Date:
GENERAL PHASING PLAN - SECOND
FLOOR
CONTRACT DOCUMENTS
FULLY SPRINKLERED
REPLACE FAN COIL UNITS, BLDG 18
41 CASTLE POINT RD.
WAPPINGERS FALLS, NY 12590
2024-12-10
GC105
620A4-22-101
DJU IJS
REV 0 CONTRACT DOCUMENTS 2024/12/10
"Unauthorized alteration or addition to any plans, specifications or reports bearing a Licensed Professional Engineer's seal is a violation of Section 7209, subdivision 2, of the New York State Education Law".
CERTIFICATE OF AUTHORIZATION NUMBER: 0020000
SCALE: 1/8" = 1'-0"
GENERAL PHASING PLAN - SECOND FLOOR1
GENERAL NOTES
1. PHASING IS DESIGNATED THROUGHOUT THE DRAWING SET VIA
2.
CONTRACTOR SHALL BE RESPONSIBLE FOR ALL WORK AREA AND LAY DOWN FENCING AREAS.
MAINTAIN SAFE AND CLEAN CONDITIONS THROUGHOUT DURATION OF PROJECT. COORDINATE
FINAL LOCATION/LAYOUT/DIMENSIONS WITH VA FOR FINAL APPROVAL.
3.
PHASING NOTES INDICATE GENERAL WORK ITEMS TO BE PERFORMED. PHASE NOTES DO NOT
IMPLY SEQUENCE OF OPERATION. CONTRACTOR IS RESPONSIBLE FOR CREATING
CONSTRUCTION SCHEDULE AND COORDINATION OF SCHEDULE AMONGST TRADES.
4.
WORK OUTSIDE THE DESIGNATED PHASE AREA MAY BE REQUIRED TO COMPLETE PHASED
WORK. CONTRACTOR IS TO COORDINATE ALL WORK WITH COR AND BETWEEN ANY AND ALL
SUBCONTRACTORS TO ENSURE CONTINUED OPERATIONS AND INTENT SHOWN THROUGHOUT
THIS DRAWING SET.
5. REFER TO SPECIFICATION 010000 GENERAL REQUIREMENTS FOR ADDITIONAL PHASING
INFORMATION.
6. REFER TO H-SERIES DRAWINGS FOR HAZARDOUS MATERIAL REQUIREMENTS
7.
INSTALL PLASTIC DUST BARRIERS TO SEAL AREA FROM NON-WORK AREA OR IMPLEMENT
CONTROL CUBE METHOD (CART WITH PLASTIC COVERING AND SEALED CONNECTION TO WORK
SITE WITH HEPA VACUUM FOR VACUUMING PRIOR TO EXIT) BEFORE CONSTRUCTION BEGINS.
8.
WHERE CEILING TILES ARE TO REMAIN DISPLACED FOR LONGER THAN A SINGLE SHIFT,
CONTRACTOR SHALL PROVIDE 1-HOUR RATED CONSTRUCTION BARRIERS FOR THAT WORK
AREA.
9. ISOLATE HVAC SYSTEM IN AREAS WHERE WORK IS BEING PERFORMED TO PREVENT
CONTAMINATION OF DUCT SYSTEM.
10. MAINTAIN NEGATIVE PRESSURE WITHIN WORK SITE UTILIZING HEPA EQUIPPED AIR FILTRATION
UNITS.
11. PLACE DUST MAT AT ENTRANCE AND EXIT OF WORK AREA.
12. COVER CONSTRUCTION WASTE BEFORE TRANSPORT IN COVERED CONTAINERS.
13. ALL WORK ASSOCIATED WITH A MAJOR PROJECT THAT HAS AN APPROVED ICRA
AUTHORIZATION FORM WILL BE ASSESSED ON AN INDIVIDUAL BASIS.
14. WET MOP AND VACUUM WITH HEPA FILTER VACUUM BEFORE LEAVING WORK AREA.
15. DO NOT REMOVE BARRIES FROM WORK AREA UNTIL A HEALTH SYSTEM RESPONSIBLE PERSON
INSPECTS COMPLETED PROJECT.
16. REMOVE BARRIER MATERIALS CAREFULLY TO MINIMIZE SPREAD OF DIRT AND DEBRIS
ASSOCIATED WITH CONSTRUCTION.
17. REMOVE ISOLATION OF HVAC SYSTEM IN AREAS WHERE WORK WAS BEING PERFORMED.
18. HOUSEKEEPING TO WIPE WORK SURFACES AND FLOORS WITH DISINFECTANT.
19. ALL PENETRATIONS THROUGH FLOORS AND/OR RATED WALLS SHALL BE FIRE SEALED PRIOR
TO THE END OF EACH SHIFT.
PHASE NOTES
1. REMOVE FCUS, DISTRIBUTION PIPING AND RISE PIPING UP TO FLOOR ABOVE.
2. INSTALL NEW PIPING AND FCUS.
3. REPAIR PIPING CHASE.
PHASE & RISER SCHEDULE
PHASE # RISER ASSOCIATED
1.1 PENTHOUSE
2.1 PENTHOUSE
2.2 CRAWLSPACE (1 THRU 12)
3.1 1
3.2 3
3.3 2
3.4 12
3.5 8
3.6 9, 10
3.7 11
3.8 7
3.9 6
3.10 5
3.11 4
15H 15E
17G 18D
16F
111 19C
20B
75A
21A
73A
59A
N
N
Exp. 11/30/2027
23 Mechanic Street, Springville, NY 14141
12/10/2024
AutoCAD SHX Text
ELEVATOR
AutoCAD SHX Text
ROOF
AutoCAD SHX Text
FD
AutoCAD SHX Text 215A
AutoCAD SHX Text one eighth inch = one foot
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text three inches = one foot
AutoCAD SHX Text 6"
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text 6"
AutoCAD SHX Text one and one half inches = one foot
AutoCAD SHX Text one inch = one foot
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text 6"
AutoCAD SHX Text 6"
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text three quarters inch = one foot
AutoCAD SHX Text one half inch = one foot
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text three eighths inch = one foot
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
5678910 3 2 1
A
ELEVATOR
SHAFT
GU CLINIC
GU CLINIC
GU CLINIC
GU CLINIC
GU CLINIC
GU CLINIC
GU CLINIC
CORRIDOR 08-
CORRIDOR 07-
CORRIDOR 06
CORRIDOR 02
CORRIDOR 03
307A
TOILET
306A
TOILET308A
TOILET
EAST
STAIR HALL
MINOR
PROCEDURE RM.
UROLOGY
PROCEDURE RM.
312C
CONFERENCE
ROOM
WAITING
ROOM
STAFF
LOUNGE
CHECK-IN
314A
LOGISTICS
STORAGE
312F
TOILET
312G
KICH.
312B
COPY
311A
TOILET
CART ON
WHEELS
ANTE
314B
EMS
STORAGE
314C
PHARMACY CARE
STORAGE
UTILITY
ROOM
321B
OFFICE
OFFICE
DATA
CLOSET
E.M.S.
CLOSET
321A
OFFICE
315A
WAITING
ROOM
OFFICE
CENTER
STAIR HALL
CORRIDOR 01
BATHROOM
324A
MAIL ROOM
IN-TAKE
RM. 01
OFFICE
CONFERENCE
ROOM
330A
TOILET
IN-TAKE
RM. 02
RECOVERY
ROOM
STORE
ROOM
IN-TAKE
RM. 03336
OFFICE
PROCEDURE
RM. 02
PROCEDURE
RM. 02
331A
CONTROL RM.
338A
CONTROL RM.
DARK ROOM
SOILED UTILITY
CLEAN
UTILITY 339
ANTE
CORRIDOR
WEST
STAIR HALL
329A
TOILET
G.U. WORK
ROOM
327A
HOUSE-
KEEPING
CC C
1110912
3.43.33.1 3.5 3.6 3.7 3.8
3.2
3.10
3.9
3.11
Project Number
Building Number
Drawing Number
Project Title
Location
Issue Date Checked Drawn
Drawing Title
Approved:
VA FORM 08 - 6231
A
Office of Construction and Facilities Management
U.S. Department of Veterans Affairs
B
C
D
E
F
A
B
C
D
E
F
21 4 5 6 7 8 9 10
PhaseARCHITECT/ENGINEER OF RECORDCONSULTANT
321 4 5 6 7 8 9 10
Project Director
Revisions: Date:
GENERAL PHASING PLAN - THIRD
FLOOR
CONTRACT DOCUMENTS
FULLY SPRINKLERED
REPLACE FAN COIL UNITS, BLDG 18
41 CASTLE POINT RD.
WAPPINGERS FALLS, NY 12590
2024-12-10
GC106
620A4-22-101
DJU IJS
REV 0 CONTRACT DOCUMENTS 2024/12/10
"Unauthorized alteration or addition to any plans, specifications or reports bearing a Licensed Professional Engineer's seal is a violation of Section 7209, subdivision 2, of the New York State Education Law".
CERTIFICATE OF AUTHORIZATION NUMBER: 0020000
SCALE: 1/8" = 1'-0"
GENERAL PHASING PLAN - THIRD FLOOR1
N
GENERAL NOTES
1. PHASING IS DESIGNATED THROUGHOUT THE DRAWING SET VIA
2.
CONTRACTOR SHALL BE RESPONSIBLE FOR ALL WORK AREA AND LAY DOWN FENCING AREAS.
MAINTAIN SAFE AND CLEAN CONDITIONS THROUGHOUT DURATION OF PROJECT. COORDINATE
FINAL LOCATION/LAYOUT/DIMENSIONS WITH VA FOR FINAL APPROVAL.
3.
PHASING NOTES INDICATE GENERAL WORK ITEMS TO BE PERFORMED. PHASE NOTES DO NOT
IMPLY SEQUENCE OF OPERATION. CONTRACTOR IS RESPONSIBLE FOR CREATING
CONSTRUCTION SCHEDULE AND COORDINATION OF SCHEDULE AMONGST TRADES.
4.
WORK OUTSIDE THE DESIGNATED PHASE AREA MAY BE REQUIRED TO COMPLETE PHASED
WORK. CONTRACTOR IS TO COORDINATE ALL WORK WITH COR AND BETWEEN ANY AND ALL
SUBCONTRACTORS TO ENSURE CONTINUED OPERATIONS AND INTENT SHOWN THROUGHOUT
THIS DRAWING SET.
5. REFER TO SPECIFICATION 010000 GENERAL REQUIREMENTS FOR ADDITIONAL PHASING
INFORMATION.
6. REFER TO H-SERIES DRAWINGS FOR HAZARDOUS MATERIAL REQUIREMENTS
7.
INSTALL PLASTIC DUST BARRIERS TO SEAL AREA FROM NON-WORK AREA OR IMPLEMENT
CONTROL CUBE METHOD (CART WITH PLASTIC COVERING AND SEALED CONNECTION TO WORK
SITE WITH HEPA VACUUM FOR VACUUMING PRIOR TO EXIT) BEFORE CONSTRUCTION BEGINS.
8.
WHERE CEILING TILES ARE TO REMAIN DISPLACED FOR LONGER THAN A SINGLE SHIFT,
CONTRACTOR SHALL PROVIDE UL APPROVED 1-HOUR RATED CONSTRUCTION BARRIERS FOR
THAT WORK AREA.
9. ISOLATE HVAC SYSTEM IN AREAS WHERE WORK IS BEING PERFORMED TO PREVENT
CONTAMINATION OF DUCT SYSTEM.
10. MAINTAIN NEGATIVE PRESSURE WITHIN WORK SITE UTILIZING HEPA EQUIPPED AIR FILTRATION
UNITS.
11. PLACE DUST MAT AT ENTRANCE AND EXIT OF WORK AREA.
12. COVER CONSTRUCTION WASTE BEFORE TRANSPORT IN COVERED CONTAINERS.
13. ALL WORK ASSOCIATED WITH A MAJOR PROJECT THAT HAS AN APPROVED ICRA
AUTHORIZATION FORM WILL BE ASSESSED ON AN INDIVIDUAL BASIS.
14. WET MOP AND VACUUM WITH HEPA FILTER VACUUM BEFORE LEAVING WORK AREA.
15. DO NOT REMOVE BARRIES FROM WORK AREA UNTIL A HEALTH SYSTEM RESPONSIBLE PERSON
INSPECTS COMPLETED PROJECT.
16. REMOVE BARRIER MATERIALS CAREFULLY TO MINIMIZE SPREAD OF DIRT AND DEBRIS
ASSOCIATED WITH CONSTRUCTION.
17. REMOVE ISOLATION OF HVAC SYSTEM IN AREAS WHERE WORK WAS BEING PERFORMED.
18. HOUSEKEEPING TO WIPE WORK SURFACES AND FLOORS WITH DISINFECTANT.
19. ALL PENETRATIONS THROUGH FLOORS AND/OR RATED WALLS SHALL BE FIRE SEALED PRIOR
TO THE END OF EACH SHIFT.
PHASE NOTES
1. REMOVE FCUS, DISTRIBUTION PIPING AND RISE PIPING UP TO FLOOR ABOVE.
2. INSTALL NEW PIPING AND FCUS.
3. REPAIR PIPING CHASE.
PHASE & RISER SCHEDULE
PHASE # RISER ASSOCIATED
1.1 PENTHOUSE
2.1 PENTHOUSE
2.2 CRAWLSPACE (1 THRU 12)
3.1 1
3.2 3
3.3 2
3.4 12
3.5 8
3.6 9, 10
3.7 11
3.8 7
3.9 6
3.10 5
3.11 4
15H 15E
17G 18D
16F
111 19C
20B
75A
21A
73A
59A
N
Exp. 11/30/2027
23 Mechanic Street, Springville, NY 14141
12/10/2024
AutoCAD SHX Text E.P.
AutoCAD SHX Text one eighth inch = one foot
AutoCAD SHX Text
Auto…
This is the start of the file's text. The full file is on GovTribe.
File details come from the government source that posted it. Updated .