TAB 9 Attachment G _ DLA Energy C QAPS.pdf

For the best experience, open this PDF portfolio in

Acrobat X or Adobe Reader X, or later.

Get Adobe Reader Now!

http://www.adobe.com/go/reader

DEFENSE LOGISTICS AGENCY ENERGY Page 1 of 1

8725 JOHN J. KINGMAN ROAD

FORT BELVOIR, VIRGINIA 22060-6222

Signature

Prepared by:

Quality / Technical Support Office Approval:

Contracting Approval:

DISTRIBUTION STATEMENT – A: APPROVED FOR PUBLIC RELEASE. DISTRIBUTION IS UNLIMITED

C16.23-2 COMMERCIAL MARINE GAS OIL MINIMUM REQUIREMENTS (DLA ENERGY APR 2021)

Product Classification

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE DLA ENERGY PRODUCT CODE UNIT OF ISSUE

9140-01-313-7776 Marine Gas Oil MGO Gallons 9140-01-417-6843 Marine Gas Oil MGT Metric Tons

Supplies delivered under this contract, the Contractor shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. The Contractor shall also comply with all applicable International Agreements, Treaties, Conventions, and the like to which the United States is a party or with whose terms the receiving activity has otherwise agreed to comply, including but not limited to, the requirements of MARPOL 73/78 Annex VI Regulations 14 & 18. The Contractor shall be responsible for determining the existence of all such requirements prior to the time deliveries are made. This includes delivery of fuel and documentation in a manner consistent with any existing or after-imposed Title V (Clean Air Act) Permits.

The list of such requirements contained in this contract is not intended to be a complete list, and the Contractor shall be responsible for determining the existence of all such requirements. Selected regional environmental requirements are highlighted in the SPECIFICATIONS (CONT’D) clause. In the event that an International, Federal, State, and /or local environmental requirement, as identified above, is more stringent than a requirement contained in this contract, the Contractor shall deliver product(s) that complies with the more stringent requirement. Product(s) that fails to meet the more stringent requirement will be considered nonconforming supply. Product(s) to be supplied shall fully meet the requirements of the applicable specification(s). In the event that compliance with the more stringent requirement causes the contractor to incur additional costs, the contractor may request an equitable adjustment.

Product shall conform to the requirements of the latest revision of ISO 8217, Category ISO-F-DMA. In Accordance with Annex A of ISO 8217, the de minimis value of FAME shall be 0.5 volume %. Offeror/Supplier shall ensure product offered meets ISO 8217 de minimis FAME requirement. The following are additional requirements or approved modifications to specifications.

(a) SPECIFICATION MODIFICATIONS

(1) TESTING

(i) Hydrogen sulfide testing is not required

(ii) In addition to ISO 8217 approved sulfur tests, the following test methods are approved for Sulfur testing: ASTM D129, D5453, D1266, D1552, D2622, D3120, D6920, D7039, or ISO16591. See section 6.3 of ISO 8217 for referee test method. For a total sulfur content of less than 0.05 mass % (500 ppm), the latest revision of ASTM D5453 is the recommended ASTM method.

(iii) The following test methods are approved for FAME testing per ISO 8217: IP 579 or ASTM D 7963. Test method EN 14078 is an equivalent test method for IP 579 and approved for FAME testing. See section 6.10 ISO 8217 for referee test method.

(iv) ASTM International Test Methods equivalent to ISO test methods referenced in ISO 8217, DMA testing, are approved for use.

(2) Environmental

(i) As of 01 JAN 2020, under the requirements listed in MARPOL 73/78 Annex VI Regulation 14, MGO-DMA (MGO & MGT) purchased under DLA Energy programs shall not exceed a revised maximum sulfur weight percent of 0.5 (% m/m). This requirement does not supersede more stringent federal, state, and local environmental requirements.

(ii) Per MARPOL 73/78 Annex VI Regulation 14, for ships operating in the most current emission control areas, the sulfur content of marine gas oil shall not exceed 0.10% mass (1000 ppm).

(iii) Per 40 CFR Section 80.510, the Marine Gas Oil sulfur requirement for all refineries and deliveries to ports within Continuous United States (CONUS) shall not exceed 0.0015 mass % (15 ppm) sulfur.

(b) ADDITIVES: Marine Gas Oil shall contain no black dye.

(c) OTHER REQUIREMENTS: Unless otherwise indicated by the Contractor in writing, prior to award, and in accordance with the

EVALUATION (SHIP’S BUNKERS) provision, the product offered shall fully meet the applicable specification. The supplier shall provide to the receiving vessel a “Statutory Sample” of at least 500 mL in volume, taken from the receiving vessel’s inlet bunker manifold, together with a Bunker Delivery Note (BDN). This sample will be sealed and carry a sample tag that provides the documentation required per MARPOL 73/78 Annex VI Regulation 18.

2021-04-08T08:59:19-0400

ATKINS.RENRICK.L.1024389320

2021-04-08T10:18:20-0400

BANISZEWSKI.DANIEL.J.1287388698

2021-04-09T08:55:33-0400

SHILLINGFORD.JAMES.V.1046542440

C16.27 FUEL, BIODIESEL (B20) (DLA ENERGY OCT 2014)

In the event that a Federal, State, or local environmental requirement is more stringent than a specification contained in this contract, the Contractor shall deliver product that complies with the more stringent requirement. Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. Offered product shall conform to the following requirements that define a fuel suitable for use in automotive diesel engines:

(a) PRODUCT COMPOSITIONAL AND PERFORMANCE REQUIREMENTS. The finished fuel shall conform to ASTM D7467, with a biodiesel blend percentage of 20 +/- 1 percent, with the exception that the biodiesel component, per ASTM D6751, shall be derived solely from either virgin or used vegetable oils. Biodiesel derived from animal fats or tallows shall not be used. Product classification is shown below:

MAXIMUM

DLA ENERGY PRODUCT SULFUR

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE CODE CONTENT RED DYE

9140-01-470-4520 Grade Number B20 S15 BDI 15 µg/g (ppm) No

Suppliers of biodiesel blends shall be certified as either BQ-9000 Producers or BQ-9000 Marketers as set forth by standards adhering to The National Biodiesel Accreditation Program. Documentation of BQ-9000 certification shall be submitted at time of offer.

(b) BLENDING. Product shall be blended prior to delivery. Manifold blending at time of delivery and blending in the receipt tank is not permitted. The resultant blended product must meet all performance requirements specified in the contract.

(c) LOW TEMPERATURE OPERABILITY. For fuel supplied during the months of October through March, the low temperature performance of B20 biodiesel shall be defined by the following property:

CLOUD POINT. Unless a more restrictive cloud point limit is specified in the contract schedule, the cloud point shall be equal to or lower than the tenth percentile minimum ambient temperature specified in Appendix X3 of ASTM D 7467.

(d) ENVIRONMENTAL PROTECTION AGENCY (EPA) REGISTRATION. B100 product must be EPA registered in accordance with 40 CFR Part 79, Registration of Fuels and Fuel Additives. The Contractor shall provide a copy of the EPA registration letter to the Contracting Officer at the time of offer.

Office Approval: Prior approval as contract provision

Contracting Approval: Prior approval as contract provision

Legal Approval:

(Only required for E QAPs)

DMM0076

Typewritten Text

DISTRIBUTION STATEMENT - A: APPROVED FOR PUBLIC RELEASE. DISTRIBUTION IS UNLIMITED

2014-12-09T09:37:22-0500

ATKINS.RENRICK.L.1024389320

Quality/Technical Support Office Approval

C16.69-1 GASOLINE AUTOMOTIVE, UNLEADED, REGULAR (PC&S) (DLA ENERGY JUN 2017)

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE DLA ENERGY PRODUCT CODE

9130-00-148-7103 Gasoline, Regular Unleaded MUR

Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with existing or future Title V (Clean Air Act) Permits. In the event that a Federal, State, or local environmental requirement is more stringent than a similar requirement in a fuel specification contained in this contract, the Contractor shall deliver product that complies with the more stringent requirement. Product that fails to meet the more stringent environmental requirement will be considered to be a nonconforming supply. All supplies furnished under this contract shall fully meet the requirements of the applicable specification(s) as cited below. In the event that compliance with the more stringent requirement causes the contractor to incur additional costs, the contractor may request an equitable adjustment.

NOTE: Gasoline Reid Vapor Pressure (RVP) specification requirements are seasonal and vary geographically. Therefore, Contractors are expected to know the In-country, State, or Federal RVP requirements of areas being supplied and comply with those requirements.

GASOLINE AUTOMOTIVE, UNLEADED, REGULAR. Gasoline shall conform to each country specification as listed below:

COUNTRY SPECIFICATION NATIONAL STOCK NUMBER

AUSTRALIA FUEL STANDARD (PETROL) 2001

CANADA CAN/CGSB-3.5-2001

JAPAN JIS K 2202

PHILIPINES PNS/DOE QS 008:2012 9130-00-148-7103

MIDDLE EAST EN 228

ALL OTHER REGIONS ASTM D4814

LOCAL SPECIFICATIONS: In-country specifications not meeting the specification requirements in the chart above, but meet local requirements may also be submitted for review and approval.

(a) OCTANE REQUIREMENTS

(1) Unleaded regular automotive gasoline shall meet the Motor Octane Number (MON), Research Octane Number (RON) and/or

Anti-Knock Index (AKI) limits described in the specification listed for each country or the in-country requirements when applicable.

(2) Reductions for altitude and seasonal variations are allowed for all AKI values in accordance with specification listed for each country requirements when applicable.

(b) OXYGENATE REQUIREMENTS.

(1) In order to achieve minimum/maximum oxygen content limits specified per Federal, State, and local environmental requirements, supplies shall only include oxygenates that are permitted by environmental regulations applicable to the time and place of delivery.

(2) Blending of oxygenates into gasoline to meet oxygenated fuel requirements shall be accomplished by mechanical mixing or agitation in a tank, or by in-line blending, prior to loading the product into transport equipment, and the resultant product must meet contract requirements.

2017-06-07T13:33:14-0400

MEREDITH.MICHAEL.E.1290973453

2017-06-07T14:14:28-0400

BANISZEWSKI.DANIEL.J.1287388698

2017-08-24T07:15:59-0400

PETERSON.DAVID.W.1074069483

C16.69-10 DIESEL FUEL SPECIFICATION (PC&S) (DLA ENERGY DEC 2016)

9140-01-524-5174 Grade Number 1-D S15 (ULSD) DS1

Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with any existing or after-imposed Title V (Clean Air Act) Permits. The list of such requirements contained in this contract is not intended to be a complete list, and the Contractor shall be responsible for determining the existence of all such requirements. Selected regional environmental requirements are highlighted in the SPECIFICATIONS (CONT’D) clause. In the event that a Federal, State, or local environmental requirement is more stringent than a fuel specification contained in this contract, the Contractor shall deliver product that complies with the more stringent fuel specification. Product that fails to meet the more stringent fuel specification will be considered to be a nonconforming supply. Product(s) to be supplied shall fully meet the requirements of the applicable specification(s) as cited below. In the event that compliance with the more stringent fuel specification causes the contractor to incur additional costs, the contractor may request an equitable adjustment.

Product shall conform to commercial specification ASTM D 975, Grade Number 1-D S15. In accordance with this specification, product shall be visually free of undissolved water, sediment, and suspended matter. Product classification is shown above.

(a) ADDITIVES.

(1) A fuel stabilizer additive conforming to MIL-S-53021, latest revision, may be blended into the fuel to improve the suitability of fuel for long term storage. Permissible additive concentrations are specified in the latest revision of QPL-53021.

(2) A corrosion inhibitor/lubricity improver additive may be blended into the fuel to inhibit corrosion and improve fuel lubricity.

Permissible additive concentration limits are specified in the latest revision of QPL 25017.

(3) A fuel system icing inhibitor may be blended into the fuel to purge small quantities of water from the fuel and prevent the formulation of ice crystals. The additive concentration shall not exceed 0.15 volume percent when tested in accordance with ASTM D 5006.

(b) BLENDING. Blending one grade of diesel fuel with another grade, or other compatible components, to produce a different grade or a variation within a grade is permitted. However, such blending shall be accomplished by mechanical mixing or agitation in a tank, or in-line blending, prior to loading the product into transport equipment, and the resultant product must meet all the requirements of the desired fuel.

(c) LOW TEMPERATURE OPERABILITY / CLOUD POINT REQUIRMENTS. The low temperature performance of diesel fuel shall be defined by the following property. Unless a more restrictive cloud point limit is specified in the contract schedule, the cloud point shall be equal to or lower than the tenth percentile minimum ambient temperature specified in Appendix X5 of ASTM D 975.

Within Alaska for activities where fuel support is limited to April-September, for example "JUN/JUL", "MAY 15 - JUN 15", "DURING SUMMER MONTHS", etc, and fuel will be used year-round in support of continuing operations, the cloud point shall be equal to or lower than the tenth percentile minimum temperature specified in Appendix X5 of ASTM D 975 for the month of January.

MEREDITH.MICHAEL.E.1290973453 Digitally signed by MEREDITH.MICHAEL.E.1290973453 Date: 2016.12.22 15:09:22 -05'00'

BANISZEWSKI.DANIEL.J.1287388698 Digitally signed by BANISZEWSKI.DANIEL.J.1287388698 Date: 2016.12.28 09:10:15 -05'00'

PETERSON.DAVID.W.1074069483 Digitally signed by PETERSON.DAVID.W.1074069483 Date: 2017.01.06 16:49:52 -05'00'

C16.69-11 DIESEL FUEL SPECIFICATION (PC&S) (DLA ENERGY DEC 2016)

9140-01-524-0139 Grade Number 2-D S15 (ULSD) DS2

Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with any existing or after-imposed Title V (Clean Air Act) Permits. The list of such requirements contained in this contract is not intended to be a complete list, and the Contractor shall be responsible for determining the existence of all such requirements. Selected regional environmental requirements are highlighted in the SPECIFICATIONS (CONT’D) clause. In the event that a Federal, State, or local environmental requirement is more stringent than a fuel specification contained in this contract, the Contractor shall deliver product that complies with the more stringent fuel specification. Product that fails to meet the more stringent fuel specification will be considered to be a nonconforming supply. Product(s) to be supplied shall fully meet the requirements of the applicable specification(s) as cited above. In the event that compliance with the more stringent fuel specification causes the contractor to incur additional costs, the contractor may

Product shall conform to commercial specification ASTM D 975. In accordance with this specification, product shall be visually free of undissolved water, sediment, and suspended matter. Product classification is shown above. Maximum sulfur content shall be 0.0015 wt%.

(1) A fuel stabilizer additive conforming to MIL-S-53021, latest revision, may be blended into the fuel to improve the suitability of fuel for long term storage. Permissible additive concentrations are specified in the latest revision of QPL-53021.

(2) A corrosion inhibitor/lubricity improver additive may be blended into the fuel to inhibit corrosion and improve fuel lubricity.

(3) A fuel system icing inhibitor may be blended into the fuel to purge small quantities of water from the fuel and prevent the formulation of ice crystals. The additive concentration shall not exceed 0.15 volume percent when tested in accordance with ASTM

(b) BLENDING. Blending one grade of diesel fuel with another grade, or other compatible components, to produce a different grade or a variation within a grade is permitted. However, such blending shall be accomplished by mechanical mixing or agitation in a tank, or in-line blending, prior to loading the product into transport equipment, and the resultant product must meet all the requirements of the

(c) LOW TEMPERATURE OPERABILITY. The low temperature performance of diesel fuel shall be defined by the following property:

CLOUD POINT. Unless a more restrictive cloud point limit is specified in the contract schedule, the cloud point shall be equal to or lower than the tenth percentile minimum ambient temperature specified in Appendix X5 of ASTM D 975. Within Alaska for activities where fuel support is limited to April-September, for example "JUN/JUL", "MAY 15 - JUN 15", "DURING SUMMER MONTHS", etc, and fuel will be used year-round in support of continuing operations, the cloud point shall be equal to or lower than the tenth percentile minimum temperature specified in Appendix X5 of ASTM D 975 for the month of January.

Date: 2016.12.22 15:09:43 -05'00'

Date: 2016.12.28 09:07:05 -05'00'

Date: 2017.01.06 16:51:05 -05'00'

C16.69-12 DIESEL FUEL SPECIFICATION (PC&S) (DLA ENERGY DEC 2016)

9140-01-541-6760 Grade Number 2-D S15 (ULSD) DSS

Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with any existing or after-imposed Title V (Clean Air Act) Permits. The list of such requirements contained in this contract is not intended to be a complete list, and the Contractor shall be responsible for determining the existence of all such requirements. Selected regional environmental requirements are highlighted in the SPECIFICATIONS (CONT’D) clause. In the event that a Federal, State, or local environmental requirement is more stringent than a fuel specification contained in this contract, the Contractor shall deliver product that complies with the more stringent fuel specification. Product that fails to meet the more stringent fuel specification will be considered to be a nonconforming supply. Product(s) to be supplied shall fully meet the requirements of the applicable specification(s) as cited below. In the event that compliance with the more stringent fuel specification causes the contractor to incur additional costs, the contractor may

Product shall conform to commercial specification ASTM D 975, Grade Number 2-D S15. In accordance with this specification, product shall be visually free of undissolved water, sediment, and suspended matter. Product classification is shown above

(1) A fuel system icing inhibitor may be blended into the fuel to purge small quantities of water from the fuel and prevent the formulation of ice crystals. The additive concentration shall not exceed 0.15 volume percent when tested in accordance with ASTM D 5006.

(2) A corrosion inhibitor/lubricity improver additive may be blended into the fuel to inhibit corrosion and improve fuel lubricity.

(3) A fuel stabilizer additive conforming to MIL-S-53021, latest revision, may be blended into the fuel to improve the suitability of fuel for long term storage. Permissible additive concentrations are specified in the latest revision of QPL-53021.

(b) BLENDING. Blending one grade of diesel fuel with another grade, or other compatible components, to produce a different grade or a variation within a grade is permitted. However, such blending shall be accomplished by mechanical mixing or agitation in a tank, or in-line blending, prior to loading the product into transport equipment, and the resultant product must meet all the requirements of the

(c) LOW TEMPERATURE OPERABILITY. The low temperature performance of diesel fuel shall be defined by the following

CLOUD POINT. Unless a more restrictive cloud point limit is specified in the contract schedule, the cloud point shall be equal to or lower than the tenth percentile minimum ambient temperature specified in Appendix X5 of ASTM D 975. Within Alaska for activities where fuel support is limited to April-September, for example "JUN/JUL", "MAY 15 - JUN 15", "DURING SUMMER MONTHS", etc, and fuel will be used year-round in support of continuing operations, the cloud point shall be equal to or lower than the tenth percentile minimum temperature specified in Appendix X5 of ASTM D 975 for the month of January.

(d) DYE REQUIREMENT. Product shall have addition of red dye. As a means of identification, the Internal Revenue Service (IRS) requires that a red dye, identified as Solvent Red 164 (alky derivatives of azo benzene azo naphthol), must be added to all nontaxable diesel and all nontaxable kerosene used for purposes other than military jet fuel. The definitions of diesel and kerosene are provided in 26 CFR Section 48.4081-1. The minimum concentration is provided in 40 CFR Part 80.

Date: 2016.12.22 15:10:02 -05'00'

Date: 2016.12.28 09:07:38 -05'00'

Date: 2017.01.06 16:52:23 -05'00'

C16.69-13 DIESEL FUEL SPECIFICATION (PC&S) (DLA ENERGY DEC 2016)

9140-01-541-6767 Grade Number 1-D S15 (ULSD) DSW

Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with any existing or after-imposed Title V (Clean Air Act) Permits. The list of such requirements contained in this contract is not intended to be a complete list, and the Contractor shall be responsible for determining the existence of all such requirements. Selected regional environmental requirements are highlighted in the SPECIFICATIONS (CONT’D) clause. In the event that a Federal, State, or local environmental requirement is more stringent than a fuel specification contained in this contract, the Contractor shall deliver product that complies with the more stringent fuel specification. Product that fails to meet the more stringent fuel specification will be considered to be a nonconforming supply. Product(s) to be supplied shall fully meet the requirements of the applicable specification(s) as cited below. In the event that compliance with the more stringent fuel specification causes the contractor to incur additional costs, the contractor may

Product shall conform to commercial specification ASTM D 975, Grade Number 1-D S15. In accordance with this specification, product shall be visually free of undissolved water, sediment, and suspended matter. Product classification is shown above. Maximum sulfur content shall be 0.0015 wt%. Product shall have addition of red dye

(1) A fuel system icing inhibitor may be blended into the fuel to purge small quantities of water from the fuel and prevent the formulation of ice crystals. The additive concentration shall not exceed 0.15 volume percent when tested in accordance with ASTM

(2) A corrosion inhibitor/lubricity improver additive may be blended into the fuel to inhibit corrosion and improve fuel lubricity.

(3) A fuel stabilizer additive conforming to MIL-S-53021, latest revision, may be blended into the fuel to improve the suitability of fuel for long term storage. Permissible additive concentrations are specified in the latest revision of QPL-53021.

(b) BLENDING. Blending one grade of diesel fuel with another grade, or other compatible components, to produce a different grade or a variation within a grade is permitted. However, such blending shall be accomplished by mechanical mixing or agitation in a tank, or in-line blending, prior to loading the product into transport equipment, and the resultant product must meet all the requirements of the

(c) LOW TEMPERATURE OPERABILITY. The low temperature performance of diesel fuel shall be defined by the following

CLOUD POINT. Unless a more restrictive cloud point limit is specified in the contract schedule, the cloud point shall be equal to or lower than the tenth percentile minimum ambient temperature specified in Appendix X5 of ASTM D 975. Within Alaska for activities where fuel support is limited to April-September, for example "JUN/JUL", "MAY 15 - JUN 15", "DURING SUMMER MONTHS", etc, and fuel will be used year-round in support of continuing operations, the cloud point shall be equal to or lower than the tenth percentile minimum temperature specified in Appendix X5 of ASTM D 975 for the month of January.

(d) DYE. As a means of identification, the Internal Revenue Service (IRS) requires that a red dye, identified as Solvent Red 164 (alky derivatives of azo benzene azo naphthol), must be added to all nontaxable diesel and all nontaxable kerosene used for purposes other than military jet fuel. The definitions of diesel and kerosene are provided in 26 CFR Section 48.4081-1. The minimum concentration is provided in 40 CFR Part 80.

Date: 2016.12.22 15:10:43 -05'00'

Date: 2016.12.28 09:07:56 -05'00'

Date: 2017.01.06 16:53:42 -05'00'

Office Approval:

C16.69-17 FUEL OIL, BURNER SPECIFICATION (PC&S) (FL2) (DLA ENERGY DEC 2016)

9140-01-546-1786 Fuel Oil, Burner No. 2 S500 FL2

Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with any existing or after-imposed Title V (Clean Air Act) Permits. The list of such requirements contained in this contract is not intended to be a complete list, and the Contractor shall be responsible for determining the existence of all such requirements. Selected regional environmental requirements are highlighted below. In the event that a Federal, State, or local environmental requirement is more stringent than a fuel specification contained in this contract, the Contractor shall deliver product that complies with the more stringent fuel specification. Product that fails to meet the more stringent fuel specification will be considered to be a nonconforming supply. Product(s) to be supplied shall fully meet the requirements of the applicable specification(s) as cited below. In the event that compliance with the more stringent fuel specification causes the contractor to incur additional costs, the contractor may request an equitable adjustment.

Product shall conform to the latest revision of commercial specification ASTM D 396, as modified by the requirement (a).

Product classification is shown in the table above.

(a) ADDITIONAL REQUIREMENT: Under this provision, PRODUCT CONTAINING USED OIL SHALL NOT BE SUPPLIED.

(b) HIGHLIGHT OF SPECIFICATION REQUIREMENTS:

(1) SULFUR REQUIREMENT: As per D396, No. 2 S500, the maximum allowable sulfur content for Burner Oil, Grade No. 2 S500 shall be 0.05 weight percent.

(2) DYE REQUIREMENT: Under United States regulations, Grade No. 2 S500 is required by 40 CFR Part 80 to contain a sufficient amount of the dye Solvent Red 164 so its presence is visually apparent. At or beyond terminal storage tanks, they are required by CFR Part 48 to contain the dye Solvent Red 164 at a concentration spectrally equivalent to 3.9 pounds per thousand barrels of the solid dye standard Solvent Red 26. As a means of identification, the Internal Revenue Service (IRS) requires that a red dye, must be added to all nontaxable diesel and all nontaxable kerosene used for purposes other than military jet fuel.

(c) BLENDING REQUIRMENT: Blending of various compatible grades of burner oil to produce an intermediate grade is permitted, however, such blending shall be accomplished by mechanical mixing or agitation in a tank, or by in-line blending, prior to loading the product into transport equipment, and the resultant product must meet all the requirements of the grade produced (Fuel Oil, Burner No. 2 S500).

Date: 2016.12.22 15:12:20 -05'00'

Date: 2016.12.28 09:09:17 -05'00'

Date: 2017.01.06 16:54:55 -05'00'

C16.69-2 GASOLINE AUTOMOTIVE, UNLEADED, MIDGRADE (MUM) (PC&S) (DLA ENERGY JUN 2017)

9130-01-272-0983 Gasoline, Midgrade Unleaded MUM

Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with existing or future Title V (Clean Air Act) Permits. In the event that a Federal, State, or local environmental requirement is more stringent than a similar requirement in a fuel specification contained in this contract, the Contractor shall deliver product that complies with the more stringent requirement. Product that fails to meet the more stringent environmental requirement will be considered to be a nonconforming supply. All supplies furnished under this contract shall fully meet the requirements of the applicable specification(s) as cited below. In the event that compliance with the more stringent requirement causes the contractor to incur additional costs, the contractor may request an equitable adjustment.

NOTE: Gasoline Reid Vapor Pressure (RVP) specification requirements are seasonal and vary geographically. Therefore, Contractors are expected to know the In-country, State, or Federal RVP requirements of areas being supplied and comply with those

GASOLINE AUTOMOTIVE, UNLEADED, MIDGRADE. Gasoline shall conform to each countries specification as listed below:

LOCAL SPECIFICATIONS: In-country specifications not meeting the specification requirements in the chart above, but meet local requirements may also be submitted for review and approval.

(1) Unleaded midgrade automotive gasoline shall meet the Motor Octane Number (MON), Research Octane Number (RON) and/or Anti-Knock Index (AKI) limits described in the specification listed for each country or the in-country requirements when

(2) Reductions for altitude and seasonal variations are allowed for all AKI values in accordance with specification listed for each

(1) In order to achieve minimum/maximum oxygen content limits specified per Federal, State, and local environmental requirements, supplies shall only include oxygenates that are permitted by environmental regulations applicable to the time and place of delivery.

(2) Blending of oxygenates into gasoline to meet oxygenated fuel requirements shall be accomplished by mechanical mixing or agitation in a tank, or by in-line blending, prior to loading the product into transport equipment, and the resultant product must

CANADA CAN/CGSB-3.5-2001

COSTA RICA RTCA 75.01.20:04

EL SALVADOR RTCA 75.01.20:04

GUATEMALA RTCA 75.01.20:04

HONDURAS RTCA 75.01.20:04 9130-01-272-0983

NICARAGUA RTCA 75.01.20:04

PHILLIPINES PNS/DOE QS 008:2012

2017-06-07T13:33:52-0400

MEREDITH.MICHAEL.E.1290973453

2017-06-07T14:15:28-0400

BANISZEWSKI.DANIEL.J.1287388698

2017-08-24T07:16:28-0400

PETERSON.DAVID.W.1074069483

C16.69-21 GASOLINE AUTOMOTIVE, ETHANOL FREE, UNLEADED, MIDGRADE (PC&S) (DLA ENERGY FEB 2020)

9130-01-686-0488 Gasoline, Ethanol Free Midgrade Unleaded EFM

Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with existing or future Title V (Clean Air Act) Permits. In the event that a Federal, State, or local environmental requirement is more stringent than a similar requirement in a fuel specification contained in this contract, the Contractor shall deliver product that complies with the more stringent requirement. Product that fails to meet the more stringent environmental requirement will be considered to be a nonconforming supply. All supplies furnished under this contract shall fully meet the requirements of the applicable specification(s) as cited below. In the event that compliance with the more stringent requirement causes the contractor to incur additional costs, the contractor may request an equitable adjustment.

Product shall conform to the latest revision of commercial specification ASTM D4814, Gasoline, Automotive, Unleaded, Midgrade. Product shall not have any ethanol added/blended in and have a de minimis of 0.5% v/v Ethanol at delivery. Product may contain oxygenate compounds, other than ethanol, that are approved by environmental regulations applicable to the time and place of delivery and commercial specification ASTM D4814.

NOTE: Gasoline Reid Vapor Pressure (RVP) specification requirements are seasonal and vary geographically. Therefore, Contractors are expected to know the In-country, State, or Federal RVP requirements of areas being supplied and comply with those

(a) TESTING:

(1) Ethanol Testing: Supplier shall be able to supply testing that delivered product meets ethanol free requirement. Testing shall be in accordance with ASTM D4815 or ASTM D5845; ASTM D4815 shall be referee method.

(2) Distillation Testing: Per ASTM D4814, Table 1, Note G, “Gasolines known from the origin to retail that will not be blended with ethanol may meet a minimum 50% evaporated distillation temperature of 66 °C (150 °F) for volatility classes D and E only.”

(b) OCTANE REQUIREMENTS

(1) Unleaded midgrade automotive gasoline shall meet the Motor Octane Number (MON), Research Octane Number (RON) and/or

Anti-Knock Index (AKI) limits described in the specification requirement.

(2) Reductions for altitude and seasonal variations are allowed for all AKI values in accordance with specification ASTM D4814 requirements when applicable.

(c) OXYGENATE REQUIREMENTS.

(1) In order to achieve minimum/maximum oxygen content limits specified per Federal, State, and local environmental requirements, supplies shall only include oxygenates, other than ethanol, that are permitted by environmental regulations applicable to the time and place of delivery.

(2) Blending of oxygenates into gasoline to meet oxygenated fuel requirements shall be accomplished by mechanical mixing or agitation in a tank, or by in-line blending, prior to loading the product into transport equipment, and the resultant product must

2020-02-21T15:19:48-0500

MEREDITH.MICHAEL.E.1290973453

2020-02-21T15:29:14-0500

BANISZEWSKI.DANIEL.J.1287388698

2020-02-27T13:08:47-0500

ROSE.JAMAAL.R.1050293366

C16.69-3 GASOLINE AUTOMOTIVE, UNLEADED, PREMIUM (MUP) (DLA ENERGY JUN 2017)

9130-00-148-7104 Gasoline, Premium Unleaded MUP

Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with existing or future Title V (Clean Air Act) Permits. In the event that a Federal, State, or local environmental requirement is more stringent than a similar requirement in a fuel specification contained in this contract, the Contractor shall deliver product that complies with the more stringent requirement. Product that fails to meet the more stringent environmental requirement will be considered to be a nonconforming supply. All supplies furnished under this contract shall fully meet the requirements of the applicable specification(s) as cited below. In the event that compliance with the more stringent requirement causes the contractor to incur additional costs, the contractor may request an equitable adjustment.

NOTE: Gasoline Reid Vapor Pressure (RVP) specification requirements are seasonal and vary geographically. Therefore, Contractors are expected to know the In-country, State, or Federal RVP requirements of areas being supplied and comply with those

GASOLINE AUTOMOTIVE, UNLEADED, PREMIUM. Gasoline shall conform to each countries specification as listed below:

CANADA CAN/CGSB-3.5-2011

JAPAN JIS K 2202

PHILIPPINES PNS/DOE QS 008:2012 9130-00-148-7104

LOCAL SPECIFICATIONS: In-country specifications not meeting the specification requirements in the chart above, but meet local requirements may also be submitted for review and approval.

(1) Unleaded premium automotive gasoline shall meet the Motor Octane Number (MON), Research Octane Number (RON) and/or

Anti-Knock Index (AKI) limits described in the specification listed for each country or the in-country requirements when

(2) Reductions for altitude and seasonal variations are allowed for all AKI values in accordance with specification listed for each

(1) In order to achieve minimum/maximum oxygen content limits specified per Federal, State, and local environmental requirements, supplies shall only include oxygenates that are permitted by environmental regulations applicable to the time and place of delivery.

(2) Blending of oxygenates into gasoline to meet oxygenated fuel requirements shall be accomplished by mechanical mixing or agitation in a tank, or by in-line blending, prior to loading the product into transport equipment, and the resultant product must

2017-06-07T13:34:12-0400

MEREDITH.MICHAEL.E.1290973453

2017-06-07T14:16:13-0400

BANISZEWSKI.DANIEL.J.1287388698

2017-08-24T07:16:56-0400

PETERSON.DAVID.W.1074069483

C16.69-7 GASOLINE, AUTOMOTIVE, UNLEADED (REFORMULATED GASOLINE) (PC&S) (DLA ENERGY DEC 2016)

9130-01-388-4080 Reformulated Gasoline, Regular MRR

Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with any existing or after-imposed Title V (Clean Air Act) Permits. The list of such requirements contained in this contract is not intended to be a complete list, and the Contractor shall be responsible for determining the existence of all such requirements. Selected regional environmental requirements are highlighted. In the event that a Federal, State, or local environmental requirement is more stringent than a fuel specification contained in this contract, the Contractor shall deliver product that complies with the more stringent fuel specification. Product that fails to meet the more stringent fuel specification will be considered to be a nonconforming supply. Product(s) to be supplied shall fully meet the requirements of the applicable specification(s) as cited below. In the event that compliance with the more stringent fuel specification causes the contractor to incur additional costs, the contractor may request an equitable adjustment.

GASOLINE Product shall conform to the latest revision of ASTM D4814, as modified by the Environmental Protection Agency (EPA) requirements detailed in 40 CFR Part 80 - "Regulation of Fuels and Fuel Additives; Subpart D Reformulated Gasoline”. In part, these regulations mandate that the Phase II complex model reformulated gasoline must meet three emissions performance requirements when compared to the baseline gasoline marketed by a refiner in 1990: a 27 percent reduction in emissions of volatile organic compounds (VOCs), a 22 percent reduction in emissions of toxic pollutants, and a 7 percent reduction in emissions of oxides of nitrogen (NOx).

Further, Phase II complex model reformulated gasoline must meet two compositional requirements: 1.3 volume percent maximum benzene and no heavy metals (lead and manganese are examples of such metals).

The latest revision of specification ASTM D 4814 applies with the following specific requirements:

(1) OCTANE REQUIREMENTS.

(i) Reformulated gasoline shall meet the minimum AKI of 87.

(ii) Reductions for altitude and seasonal variations are allowed for all AKI values in accordance with figures X1.2 and X1.3 of ASTM D 4814.

(iii) For regular unleaded gasohol, in addition to an AKI of 87 minimum, the MON must not be less than 82.

(2) OXYGENATE REQUIREMENTS.

(i) In order to achieve minimum/maximum oxygen content limits specified per Federal, State, and local environmental requirements, suppliers shall only include oxygenates that are permitted by environmental regulations applicable to the time and place of delivery.

(ii) Blending of permissible oxygenate into reformulated gasoline shall be accomplished by mechanical mixing or agitation in a tank, or by in-line blending, prior to loading the product into transport equipment, and the resultant product must meet contract requirements.

Date: 2016.12.22 15:08:13 -05'00'

Date: 2016.12.28 08:56:47 -05'00'

Date: 2017.01.06 13:37:50 -05'00'

C02 Prescription: 11.9001(a) All solicitations and contracts shall include procurement note C02.

C02 Manufacturing Phase-Out or Discontinuation of Production, Diminishing Sources, and Obsolete Materials or Components (DEC 2016) The contractor shall notify the contracting officer immediately upon determining the unavailability of obsolete materials or components. The contractor may recommend a solution to include the impact on the contract price and delivery. The contractor shall not initiate any item redesign or incur any additional costs without the express, written authorization of the contracting officer. In the event that manufacturing phase-out or discontinuance of production of such items is contemplated, the contractor is required to notify the contracting officer and publish the discontinuance in the Government-Industry Data Exchange Program (GIDEP), where feasible; and to provide immediate advance notice of production phase-out to DLA DMSMS at dscc.dmsms@dla.mil.

C03 Prescription: 4.703(a) Contracting officers shall include procurement note C03 in solicitations and awards.

C03 Contractor Retention of Supply Chain Traceability Documentation (JUN 2020) (1) By submitting a quotation or offer, the contractor, if it is not the manufacturer of the item, is confirming it currently has, or will obtain before delivery, and shall retain documented evidence (supply chain traceability documentation), as described in paragraph (2) of this procurement note, demonstrating the item is from the approved manufacturer and conforms to the technical requirements. (2) At a minimum, the supply chain traceability documentation for the item shall include: basic item description, part number and/or national stock number, manufacturing source, manufacturing source’s Commercial and Government Entity (CAGE) code, and clear identification of the name and location of all supply chain intermediaries between the manufacturer to the contractor to item(s) acceptance by the Government. The documentation should also include, if available, the manufacturer's batch identification for the item(s), such as date codes, lot codes, or serial numbers. (3) Contractors can find examples of acceptable supply chain traceability documentation at the Counterfeit Detection and Avoidance Program (CDAP) website (http://www.dla.mil/LandandMaritime/Business/Selling/Counterfeit-Detection-AvoidanceProgram/). 1

(4) The contractor shall immediately make documentation available to the contracting officer upon request. The contracting officer determines the acceptability and sufficiency of documentation. The contractor shall retain supply chain traceability documentation for six years after final payment under this contract for audit and other valid government purposes. If the contractor fails to retain or provide the documentation, or the contracting officer finds the documentation to be unacceptable, the contracting officer may take corrective action, including, but not limited to, cancellation of undelivered orders or rejection of delivered supplies.

C14 Prescription: 46.407(b)(S-92) Contracting officers shall include procurement note C14 in solicitations and awards.

C14 Correction of Nonconforming Packaging or Marking (MAY 2020) (1) The Government may correct nonconforming packaging or marking for receipts of DLA owned materiel if the estimated costs of correction are $1,000 or less. The contracting officer will advise the contractor of the discrepancy and that the Government has corrected the packaging or marking. The contracting officer will make a determination concerning appropriate reimbursement by the contractor for the Government’s costs to correct the deficiencies. Upon determining that reimbursement is required, the contracting officer will send a notice to the contractor. Upon receipt of notice from the contracting officer, the contractor shall reimburse the Government for the costs incurred by the Government to correct the deficiencies. (2) If the estimated costs of correction for receipts of DLA-owned materiel are more than $1,000, the contracting officer will advise the contractor of the discrepancy and have the materiel returned to the contractor for correction/resubmittal; or, if there are urgent requirements, have the Government remediate the discrepancy at the contractor’s expense. If the Government remediates the discrepancy, the contracting officer will make a determination concerning appropriate reimbursement by the contractor for the Government’s costs to correct the deficiencies. Upon determining that reimbursement is required, the contracting officer will send a notice to the contractor. Upon receipt of notice from the contracting officer, the contractor shall reimburse the Government for the costs incurred by the Government to correct the deficiencies.

DEFENSE LOGISTICS AGENCY ENERGY

C16.08-1 TURBINE FUEL, AVIATION (JET A) (DLA ENERGY JUL 2022)

NATIONAL STOCK NUMBER PRODUCT NOMENCLATURE PRODUCT CODE

9130-00-359-2026 Turbine Fuel, Aviation, Jet A JAA

Supplies delivered under this contract shall conform to all Federal, State, and local environmental requirements applicable to the geographic location of the receiving activity on the date of delivery. This includes delivery of fuel and documentation in a manner consistent with any existing or after-imposed Title V (Clean Air Act) Permits.

(a) PRODUCT REQUIREMENTS. Jet A shall conform to the requirements of the latest version of ASTM D 1655, Standard Specification for Aviation Turbine Fuels, except as modified below, at the custody transfer point.

(b) SPECIFICATION MODIFICATIONS

(1) Microseparometer (MSEP).

(i) The following MSEP ratings apply in the presence of the additives listed below. Values apply at point of manufacture:

Jet-A Additive MSEP Rating, min.

Fuel System Icing Inhibitor (FSII) 85

Corrosion Inhibitor/Lubricity Improver (CI/LI) 80 Fuel System Icing Inhibitor (FSII) and Corrosion

Inhibitor/Lubricity Improver (CI/LI)

(ii) MSEP shall be performed on unadditized Jet A that has a custody transfer point on the distribution system using, D7224 or D8073. If either method is not available testing may be conducted with D3948. Passing results (min 85) for D3948 will be considered acceptable. Test failures using D3948 shall be retested using D7224 or D8073. If fuel passes D7224 with a minimum limit of 85 or D8073 with a limit of 88, the fuel is acceptable with no further action.

(2) Fatty Acid Methyl Ester (FAME)

(i) For offerors that will be offering Jet A FOB Destination and/or Origin TT, which involves staging jet fuel at a terminal via a multi-product pipeline, a Certificate of Quality of the issue tank must include testing for FAME for Acceptance of the fuel. The Test method to be used is either IP 585, IP 583, IP 590, IP 599, or ASTM D 7797. The Referee Method is IP

585. Current ASTM D1655 Jet A specification allows no more than 50 parts per million of FAME in jet fuel.

(c) ADDITIVES.

(1) Additives shall not be premixed with other additives before injection into the fuel.

(2) FUEL SYSTEM ICING INHIBITOR (FSII). When required by contract line item-

(i) FSII shall be added to the fuel and shall be Diethylene Glycol Monomethyl Ether (DIEGME) conforming to the latest version of ASTM D4171, Standard Specification for FSIIs, Type III or MIL-DTL-85470B, dated June 15, 1999, revalidated August 28, 2019, Inhibitor, Icing, Fuel System, High Flash, NATO Code Number S-1745.

(ii) FSII shall be added to the fuel so that the resulting concentration in the final blend is between 0.07% and 0.10% by volume.

(iii) When using the 20-ounce aerosol can to introduce FSII during over the wing refueling, determine the fuel quantity and calculate the amount of required additive. This additive shall be added gradually during filling to permit proper blending in the fuel. One can of aerosol additive will inhibit 180 gallons of fuel to 0.087 percent by volume. The use of aerosol FSII is not permitted for U.S. Navy aircraft refueling.

(3) CORROSION INHIBITOR/LUBRICITY IMPROVER (CI/LI). When required by contract line item-

(i) The additive must conform to MIL-PRF-25017H with Amendment 1, dated August 4, 2011, revalidated May 25, 2021, Inhibitor, Corrosion/Lubricity Improver, Fuel Soluble (NATO S-1747), found in ASSIST and shall be listed in the electronic Qualified Products List (QPL)-25017, located in the Qualified Products Database (QPD) found at https://assist.dla.mil (or…