Tab 02. 6645011064303.pdf

ITEM PURCHASE DESCRIPTION

General Services Administration

Printed on: 2/13/2020, 1:09:49 PM

6645-01-106-4303 UI: EA

STOPWATCH

DESCRIPTION

ITEM NAME STOPWATCH

MINIMUM LENGTH OF NYLON LANYARD 36.00 INCHES

MINIMUM OPERATING TEMPERATURE 14.00 DEGREES FAHRENHEIT

MAXIMUM OPERATING TEMPERATURE 122.0 DEGREES FAHRENHEIT

OVERALL HIGH TEMP RELATIVE HUMIDITY 50.00 PERCENT (+ /- 20 PERCENT)

ACCURACY WITHIN 0.03 PERCENT AT 25 DEGREES

CELSIUS

UNIT TYPE DIGITAL STOPWATCH

DISPLAY SIZE JUMBO

DIGITAL DISPLAY TYPE HOUR, MINUTE, SECOND, TENTHS AND

HUNDRETHS

OF A SECOND, MONTH, DAY, DATE AND ALARM

CONTROLS TIME-OUT MODE, TWO SEPARATE CONTROLS

FOR

START/STOP AND RESET

BUTTON TYPE EXTRA LARGE GRIP BUTTONS

FIT TYPE MADE TO FIT IN PALM OF HAND

POWER SOURCE BATTERY

TIME DISPLAY LIQUID CRYSTAL

CASE AND INNER WORKINGS QUALITY AND STRENGTH / DURABILITY MADE

TO

LAST MINIMUM OF TWO YEARS OR NORMAL USE.

WARRANTY WARRANTED BY CONTRACTOR FOR PARTS

AND

LABOR FOR TWO YEARS FROM DATE OF DELIVERY

TO GOVERNMENT

SPECIAL FEATURE SPLIT MODE DISPLAY WHILE TIMING

CONTINUES;

RESOLUTION IS 1/100 SECOND FOR FIRST 30

MINUTES AND THEN 1 SECOND INCREMENTS FOR

UP TO 24 HOURS

ENVIRONMENTAL PROTECTION WATER, DUST, AND SHOCK RESISTANT

PACKAGING/PACKING

PACKAGING/PACKING: Each item shall be packaged in accordance with normal commercial practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage.

The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.

For additional references, see below link:

https://vsc.gsa.gov/Marking_Labeling_Packaging/

MARKING

For civilian destinations - In accordance with FED-STD-123H, dated August 8, 2007. For military destinations - In accordance with MIL-STD-129R, dated February 18, 2014. Bar code marking shall be included for both civilian and military destinations.

For additional references, see below link:

FED-STD-123H

https://vsc.gsa.gov/administration/files/FEDSTD123H.pdf

MIL-STD-129R

http://www.dla.mil/Portals/104/Documents/LandAndMaritime/V/VS/Packaging/LM_MILSTD 129R_151007.pdf

PALLETIZATION

PALLETIZATION & PREPARATION FOR DELIVERY: The item(s) shall be packaged and packed to afford adequate protection against physical damage during shipment from the supplier to the first receiving activity. The pack shall comply with the rules and regulations applicable to the mode of transportation. The package shall be the same as that normally provided by the supplier. If pallet or skid is used for shipping, it shall be made in accordance with normal industry standards. In the event a wooden pallet or skid is used for shipping, the following notice shall apply:

Notice of special requirements for shipment to all countries that have endorsed the IPPC Guidelines for treatment of non-manufactured wood packaging: The International Plant Protection Convention (IPPC) has approved and published on March 15, 2002, Guidelines for Regulating Wood Packaging Material in International Trade . Countries endorsing the IPPC Guidelines are found at http://www.aphis.usda.gov/ppq/swp/. Clause D-FSS-468 requires non-manufactured wood pallets and other non-manufactured wood packaging material used in shipments destined to IPPC compliant countries require the appropriate wood treatment. Additionally, shipments delivered to DOD distribution facilities or freight consolidation points for eventual delivery to or through EU/IPPC countries shall comply with applicable DLA Regulations and Procurement Letter PROCLTR 02-17.

PCM

Regulatory Requirements: The offerer/contractor is encouraged to provide energy-efficient products to the maximum extent practicable in accordance with paragraph 23.203 of the Federal Acquisition Regulations (FAR).

The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract.

QUALITY ASSURANCE

PRODUCT CONFORMANCE. The product provided shall meet the salient characteristics of this commercial item description. The quality of the product sold to the government shall be equal to or better than the quality of the product sold by the manufacturer in the commercial market. The government reserves the right to require proof of such conformance.

WORKMANSHIP: The material shall be uniformly fabricated in accordance with good commercial practice, and free from cracks, cuts, holes, chafed spots, or other defects which impair its usefulness. The material shall be free from dirt, contamination, mold release compounds, or other foreign matter.