SR1 Mtrl Sbmtl 19B - As-Builts 3.pdf

T T

E E

SYMBOL DESCRIPTION

POWER DISTRIBUTION

SURFACE/FLUSH MOUNTED BRANCH

CIRCUIT PANELBOARD. 208Y/120V OR

240/120V. REFER TO PANELBOARD

SCHEDULE

MANUAL MOTOR STARTER OR MOTOR

RATED SWITCH. DESIGNATION REFERS TO

ELECTRIC EQUIPMENT AND CONTROL

SCHEDULE

NON-FUSED DISCONNECT SWITCH.

DESIGNATION REFERS TO ELECTRIC

EQUIPMENT AND CONTROL SCHEDULE

ELECTRICAL

SYMBOL DESCRIPTION

DUPLEX RECEPTACLE,

SUBSCRIPTS AS FOLLOWS:

AFI

CR

EP

GFI

H

IG

SS

WP

TR

WR

USB

ARC FAULT INTERRUPTER

CORROSION RESISTANT

EXPLOSION PROOF

GROUND FAULT INTERRUPTER

HOSPITAL GRADE

ISOLATED GROUND

SURGE SUPPRESSION

WEATHER PROOF

TAMPER RESISTANT

WEATHER RESISTANT

UNIVERSAL SERIAL BUS

SYMBOL LIST

JUNCTION BOX

MOTORM

MS

J

EMERGENCY POWER OFF PUSHBUTTONEPO

120 VOLT CONNECTION TO EQUIPMENT

E-3

SYMBOL DESCRIPTION

MISCELLANEOUS

REFERENCE TO DRAWING NOTE

REFERENCE TO EQUIPMENT OR

FEEDER NUMBER

DETAIL REFERENCE SYMBOL

SYMBOL DESCRIPTION

LINE STYLES

INDICATES NEW DEVICE OR EQUIPMENT

REFERENCE TO DEMOLITION NOTE2

INDICATES EXISTING DEVICE OR EQUIPMENT

TO REMAIN

INDICATES DEVICE OR EQUIPMENT TO BE

REMOVED OR RELOCATED

INDICATES ELECTRIC SERVICE LINE

INDICATES TELEPHONE SERVICE LINE

NUMBER INDICATES CIRCUIT BREAKER NO.1

GENERAL SITE NOTES APPLY TO ALL SITE ELECTRICAL DRAWINGS.

OBTAIN ALL PERMITS AND INSPECTIONS REQUIRED BY THE CITY OF

CORNELL.

THE ELECTRICAL CONTRACTOR SHALL ENGAGE THE SERVICES OF A

QUALIFIED SUBCONTRACTOR FOR EXCAVATION, BACKFILL AND CONCRETE

WORK.

A MINIMUM OF TWO DAYS PRIOR TO EXCAVATION, CONTACT DIG SAFELY

NEW YORK, INC (1-800-962-7962) AND OBTAIN A STAKEOUT OF ALL PUBLIC

AND PRIVATE UTILITIES LOCATED IN THE AREA OF EXCAVATION.

COORDINATE PRIVATE UTILITIES WITH THE OWNER PRIOR TO EXCAVATION.

HAND EXCAVATE ADJACENT EXISTING UTILITIES INCLUDING STORM AND

SANITARY SYSTEMS TO AVOID DAMAGE. REPORT ANY DAMAGED UTILITIES

TO THE OWNERS REPRESENTATIVE IMMEDIATELY.

PROVIDE BRACING, SHORING, SHEATHING AND OTHER WORK FOR

PROTECTION OF PERSONNEL, THE CONTRACT WORK, EXCAVATIONS,

TREES, SHRUBS, EXISTING STRUCTURES, AND SURROUNDING PROPERTIES.

PROVIDE AND MAINTAIN BARRICADES, WARNING SIGNS, FLAGS, AND

LIGHTS TO PROVIDE PROTECTION FOR WORK, WORKMEN, PUBLIC, AND

PROPERTY. COORDINATE PARKING LOT AND/OR PARKING GARAGE

DISRUPTIONS WITH THE OWNER IN ADVANCE.

PROVIDE PUMPS, HOSES, PIPE, LABOR AND FUEL NECESSARY TO KEEP

EXCAVATIONS FREE OF WATER ACCUMULATION. OPERATE AND MAINTAIN

EQUIPMENT. DISCHARGE WATER IN MANNER NOT TO UNDERMINE OR

DISTURB EXISTING OR ADJACENT STRUCTURES OR LAND. DO NOT

DISCHARGE DIRT, BACKFILL, DEBRIS, INTO SANITARY OR STORM

DRAINAGE SYSTEMS.

INSTALL TELEPHONE, CABLE AND ELECTRIC CONDUITS AS STRAIGHT AS

POSSIBLE. INSTALL CONDUITS BELOW SITE LIGHTING CONDUITS AND GAS

LINES AND ABOVE WATER, STORM, AND SANITARY PIPING.

TRANSITION ALL CONDUITS TO GRS PRIOR TO RISING ABOVE GRADE.

MAINTAIN ROAD ACCESS AT ALL TIMES. PROVIDE STEEL PLATES OVER

TRENCH AS REQUIRED.

PROTECT UTILITIES, SIDEWALKS, STRUCTURES, PAVEMENTS AND OTHER

FACILITIES FROM DAMAGE CAUSED BY SETTLING, LATERAL MOVEMENTS,

UNDERMINING, WASHOUTS AND OTHER HAZARDS CREATED BY EXCAVATION

WORK.

COMPLETELY RESTORE THE AREA TO THE CONDITION PRIOR TO THE

START OF EXCAVATION AND TRENCHING WORK.

GENERAL SITE NOTES:

A.

B.

C.

D.

E.

F.

G.

H.

I.

J.

K.

L.

M.

SYMBOL DESCRIPTION

ABBREVIATIONS AND TAGS

LINETYPE LEGEND

SYMBOL DESCRIPTION

AFF ABOVE FINISHED FLOOR

(E) EXISTING

EC ELECTRICAL CONTRACTOR

ERL EXISTING TO RELOCATE

EXISTING TO REMAINETR

GC GENERAL CONTRACTOR

MC MECHANICAL CONTRACTOR

NC NORMALLY CLOSED

NO NORMALLY OPEN

NTS NOT TO SCALE

PUMPP

POINT OF CONNECTION

POINT OF DISCONNECTION

INSTALLATION KEYNOTE

REMOVAL KEYNOTE

WPCO WALL PLATE CLEANOUT

WH WALL HYDRANT

VTR VENT THROUGH ROOF

RPZ REDUCED PRESSURE ZONE

PD PUMP DISCHARGE

PLUMBING CONTRACTORPC

COLD WATER PIPING (C)

HOT WATER PIPING (H)

HW RECIRCULATION PIPING (HWR)

VENT PIPING (V)

STORM PIPING (ST)

SANITARY OR WASTE PIPING

(SAN or W)

G NATURAL GAS PIPING (G)

IW INDIRECT WASTE PIPING (IW)

W WATER MAIN (EXTERIOR)

DIRECTION OF FLOW

EXISTING PIPING

PIPING TO BE REMOVED

PIPING SYMBOLS

SYMBOL DESCRIPTION

ELBOW UP, ELBOW DOWN

DROP CONNECTION

ROLL DOWN

CLEANOUT (CO)

STRAINER

UNION

CAP OR PLUG

SHUT OFF VALVE

AQUASTAT

CHECK VALVE

PRESSURE REGULATING VALVE

BALANCE VALVE

ANGLE VALVE

REGULATOR

SOLENOID VALVE

3-WAY VALVE

RELIEF VALVE

PLUG VALVE

BUTTERFLY VALVE

NEEDLE VALVE

TS VALVE WITH TAMPER SWITCH

FS FLOW SWITCH

SS

ST

V

HWR

CO

TURNER

E N G I N E E R I N G , P C

One Woodbury Boulevard Rochester, NY 14604

585.381.3360 Tel

Project No.

IT IS A VIOLATION OF LAW FOR ANY PERSONS,

UNLESS ACTING UNDER THE DIRECTION OF A

LICENSED PROFESSIONAL ENGINEER, TO ALTER

ANY ITEM ON THIS DOCUMENT IN ANY WAY. ANY

LICENSEE WHO ALTERS THIS DOCUMENT IS

REQUIRED BY LAW TO AFFIX HIS OR HER SEAL

AND THE NOTATION "ALTERED BY", FOLLOWED

BY HIS OR HER SIGNATURE AND A SPECIFIC

DESCRIPTION OF THE ALTERATIONS.

Client

Project

Drawing

Issue Date:

Proj. No.

Sheet

Proj. Status:

EP001

GENERAL NOTES,

SPECIFICATIONS, AND

SYMBOLS

19223

CORNELL USDA

GENERATOR

CORNELL COOPERATIVE

EXTENSION

19223

01/02/2020

ISSUED FOR BID

ELECTRICAL SPECIFICATIONS

1. PROVIDE ALL LABOR, MATERIALS, EQUIPMENT AND SERVICES TO PERFORM

ALL OPERATIONS REQUIRED FOR THE COMPLETE INSTALLATION AND

RELATED WORK AS SHOWN ON DRAWINGS AND SPECIFIED HEREIN. ELECTRIC

EQUIPMENT SHALL BE INSTALLED IN A NEAT AND WORKMAN LIKE MANNER.

PROVIDE ALL ELECTRICAL EQUIPMENT CONNECTIONS. PROVIDE ALL

REQUIRED SUPPORTS AND ACCESSORIES. INSTALL ALL WORK IN

COMPLIANCE WITH LATEST EDITION OF THE NATIONAL ELECTRICAL CODE,

NFPA-70, NEW YORK STATE UNIFORM FIRE PREVENTION AND BUILDING CODE,

NEW YORK STATE ENERGY CONSERVATION CONSTRUCTION CODE, OSHA

REQUIREMENTS, AND LOCAL ORDINANCES.

2. INSTALL ALL WIRING AND EQUIPMENT IN ACCORDANCE WITH THE 2014

NATIONAL ELECTRICAL CODE.

3. OBTAIN AN UNDERWRITERS CERTIFICATE UPON SUBSTANTIAL COMPLETION.

4. COORDINATE ALL WORK WITH OTHER TRADES.

5. WIRE SHALL BE STRANDED COPPER WITH THHN/THWN INSULATION, MINIMUM

#12 AWG.

6. INTERIOR CONDUIT SHALL BE EMT WITH COMPRESSION FITTINGS.

7. EXTERIOR, ABOVE GRADE CONDUIT SHALL BE RIGID STEEL WITH THREADED

FITTINGS.

8. EXTERIOR, BELOW GRADE CONDUIT SHALL BE PVC, SCHEDULE 80, DIRECT

BURIED.

9. TYPE MC CABLE WITH A SEPARATE INSULATED GROUND IS PERMITTED. IN

INTERIOR, CONCEALED LOCATIONS. SUPPORT CABLE ON MINIMUM 4.5'

CENTERS.

10. EMERGENCY GENERATOR SHALL BE AS FOLLOWS:

•25 KW/31.25 KVA

•208Y/120 VOLTS

•NATURAL GAS FIRED

•ALUMINUM, WEATHER RESISTANT HOUSING, BISQUE COLOR

•100A-3P OUTPUT CIRCUIT BREAKER

•GENERATOR ANNUNCIATOR PANEL

•DESIGN MAKE: GENERAC PROTECTOR SERIES, MODEL RG025, OR

APPROVED EQUAL

11. AUTOMATIC TRANSFER SWITCH SHALL BE AS FOLLOWS:

•250 VOLT, 100 AMPERE, THREE POLE

•NEMA 3R

•BREAK BEFORE MAKE

•DESIGN MAKE: GENERAC, OR APPROVED EQUAL

12. ALL HOMERUNS TO PANELBOARDS SHALL BE INSTALLED IN EMT CONDUIT.

TYPE MC CABLE MAY BE USED FROM OUTLET BOXES IN THE CEILING TO

DEVICES AND LUMINAIRES, AND MAY BE RUN HORIZONTALLY IN THE METAL

STUD PARTITIONS.

13. PROVIDE UPDATED TYPE-WRITTEN DIRECTORIES FOR ALL PANELBOARDS

AFFECTED BY THIS PROJECT.

14. ALL EXPOSED WIRING SHALL BE INSTALLED IN CONDUIT OR SURFACE METAL

RACEWAY.

15. WHEREVER POSSIBLE, INSTALL ALL RACEWAYS CONCEALED AND DEVICES

FLUSH MOUNTED. WHERE REQUIRED DUE TO FIELD CONDITIONS, PROVIDE

SURFACE METAL RACEWAY. PAINT TO MATCH EXISTING SURFACES.

16. OUTLET BOXES AND COVERS SHALL BE GALVANIZED STEEL, NOT LESS THAN

1-1/2" DEEP, 4" SQUARE OR OCTAGONAL, WITH KNOCKOUTS. OUTLET BOXES

EXPOSED TO MOISTURE, EXTERIOR, WET OR DAMP LOCATIONS SHALL BE

CADMIUM CAST ALLOY COMPLETE WITH THREADED HUBS AND GASKETED

SCREW FASTENED COVERS. MINIMUM BOX SIZE SHALL BE AS INDICATED IN

ARTICLE 370 OF THE NATIONAL ELECTRIC CODE FOR THE CONDUCTORS AND

DEVICES INSTALLED. MAKE SHALL BE STEEL CITY OR EQUAL.

17. DUPLEX RECEPTACLES SHALL BE CONSTRUCTION GRADE. INTERIOR TYPE

SHALL BE DUPLEX, 20 AMPERE, TWO-POLE, THREE-WIRE, 125 VOLTS AC,

GROUNDING, WITH SIDE AND BACK TERMINAL CONNECTIONS AND SPLITWIRING

LINK, U.L. LISTED, WITH THERMOPLASTIC COVERPLATES. COLOR TO BE LIGHT

ALMOND. MAKE SHALL BE HUBBELL OR EQUAL.

18. PROVIDE LABELS ON ALL RECEPTACLES INDICATING BRANCH CIRCUIT PANEL

AND CIRCUIT NUMBER.

19. WIRING DEVICES SHALL BE CONSTRUCTION GRADE, LIGHT ALMOND IN

COLOR, WITH THERMOPLASTIC COVERPLATES. MAKE SHALL BE HUBBELL OR

EQUAL.

20. WEATHER RESISTANT DEVICE COVERS SHALL BE UL LISTED WITH THE DEVICE

PLUGGED IN. MAKE SHALL BE HUBBELL OR EQUAL.

21. PANELBOARDS SHALL HAVE ALUMINUM BUS WITH PLUG-ON CIRCUIT BREAKERS

AND HINGED TRIM. COORDINATE TRIM TYPE IN THE FIELD. MAKE SHALL BE

SQUARE D OR EQUAL.

22. DISCONNECT SWITCHES SHALL BE HEAVY DUTY WITH COPPER BUS. KNIVES

SHALL BE VISIBLE IN THE OPEN POSITION. MAKE SHALL BE SQUARE D OR

EQUAL.

23. MANUAL MOTOR STARTERS AND MOTOR RATED SWITCHES SHALL BE 277

VOLT, 30 AMPERE RATED, IN A NEMA 1 ENCLOSURE WITH A H-O-A SELECTOR

SWITCH AND A RELAY FOR REMOTE CONTROL OF THE EQUIPMENT IN THE

AUTO MODE. PROVIDE OVERLOADS AS REQUIRED. MAKE SHALL BE SQUARE

D CLASS 2510 OR EQUAL.

24. PROVIDE FIRE STOPPING FOR ALL PENETRATIONS THROUGH FLOORS, WALLS

AND ALL OTHER RELATED ASSEMBLIES. PROVIDE FIRE STOPPING SYSTEMS

IN ACCORDANCE WITH ASTM E814.

ELECTRICAL GENERAL NOTES

A. GENERAL NOTES APPLY TO ALL ELECTRICAL DRAWINGS.

B. PROVIDE UPDATED TYPE WRITTEN PANELBOARD SCHEDULES FOR ALL

PANELS USED IN THIS PROJECT.

C. REFER TO CORNELL STANDARD 260526 GROUNDING AND DETAILS

2.3.1 - 2.3.6.

D. PROVIDE BLANK COVERPLATES ON ALL EXISTING AND NEW UNUSED

OUTLET BOXES.

E. COORDINATE ALL CONDUIT RUNS WITH OTHER TRADES PRIOR TO

ROUGH-IN. RELOCATE ANY CONDUITS AS NECESSARY TO PERMIT

INSTALLATION OF DUCTWORK, PIPING OR ANY SUPPORTS.

F. PROVIDE CUTTING, PATCHING TO MATCH, AND FIRE SEAL AS REQUIRED

WHERE EXISTING COMMUNICATION OR ELECTRICAL WORK HAS BEEN

REMOVED AND WHERE NEW WORK IS INSTALLED. COORDINATE WITH

GENERAL CONTRACTOR.

G. REFER TO ATTACHEMENT 4 - NYSEG PAD MOUNTED TRANSFORMER

FOR TRANSFORMER PAD, METERING, AND TRANSFORMER

LOCATION/SET BACK REQUIREMENTS.

H. NOT USED.

I. COORDINATE MOUNTING HEIGHTS OF DEVICES WITH ARCHITECTURAL

ELEVATIONS AND OWNER PRIOR TO ROUGH-IN.

J. REFER TO ARCHITECTURAL PLANS FOR PHASING.

ALL WORK AND MATERIALS SHALL CONFORM TO AND BE INSTALLED,

INSPECTED AND TESTED IN ACCORDANCE WITH THE GOVERNING RULES AND

ALL REGULATIONS OF FEDERAL, STATE AND LOCAL GOVERNMENTAL

AGENCIES.

EACH CONTRACTOR SHALL HOLD A LICENSE AND/OR CERTIFICATION TO

PERFORM THE WORK REQUIRED WITHIN THE CONTRACT DOCUMENTS. COPIES OF

CURRENT LICENSE AND/OR CERTIFICATION SHALL BE SUBMITTED TO ENGINEER

AND OWNER’S REPRESENTATIVE FOR APPROVAL PRIOR TO START OF WORK.

APPLY AND INSTALL MATERIALS, EQUIPMENT, AND SPECIALTIES IN

ACCORDANCE WITH MANUFACTURER'S WRITTEN INSTRUCTIONS. CONFLICTS

BETWEEN THE MANUFACTURER'S INSTRUCTIONS AND THE CONTRACT DOCUMENTS

SHALL BE REFERRED TO THE ENGINEER AND OWNER'S REPRESENTATIVE FOR

RESOLUTION.

ALL WORK SHALL BE DONE IN A NEAT AND WORKMANLIKE MANNER. ALL

METHODS OF CONSTRUCTION, DETAILS OF WORKMANSHIP, THAT ARE NOT

SPECIFICALLY DESCRIBED OR INDICATED IN THE CONTRACT DOCUMENTS,

SHALL BE SUBJECT TO THE CONTROL AND APPROVAL OF THE ENGINEER AND

OWNER'S REPRESENTATIVE. EQUIPMENT AND MATERIALS SHALL BE OF THE

QUALITY AND MANUFACTURE INDICATED. THE EQUIPMENT SPECIFIED IS BASED

UPON THE ACCEPTABLE MANUFACTURERS LISTED. WHERE "APPROVED EQUAL" IS

STATED, EQUIPMENT SHALL BE EQUIVALENT IN EVERY WAY TO THE EQUIPMENT

SPECIFIED AND WILL BE ALLOWED SUBJECT TO APPROVAL.

MATERIALS SHALL HAVE A FLAME SPREAD RATING OF 25 OR LESS AND A

SMOKE DEVELOPED RATING OF 50 OR LESS, IN ACCORDANCE WITH NFPA 255.

EQUIPMENT SHALL BEAR THE UNDERWRITER'S LABORATORIES (UL), OR OTHER

APPROVED AGENCY-LISTING/LABEL. THIS LISTING REQUIREMENT APPLIES TO

THE ENTIRE ASSEMBLY. ANY MODIFICATIONS TO EQUIPMENT TO SUIT THE INTENT

OF THE SPECIFICATIONS SHALL BE PERFORMED IN ACCORDANCE WITH THE

NATIONAL ELECTRIC CODE AND LISTED BY U.L. POTABLE WATER SYSTEMS AND

EQUIPMENT SHALL BE BUILT ACCORDING TO AWWA STANDARDS. GAS-FIRED

EQUIPMENT AND SYSTEM SHALL MEET AGA REGULATIONS AND SHALL HAVE AGA

LABEL. ALL MATERIALS, UNLESS OTHERWISE SPECIFIED, SHALL BE NEW AND BE

THE STANDARD PRODUCTS OF THE MANUFACTURER. USED EQUIPMENT OR

DAMAGED MATERIAL WILL BE REJECTED. CATALOG NUMBERS ARE SOMETIMES

LISTED IN THE SPECIFICATIONS TO AID SELECTION OF THE EQUIPMENT AND ARE

FOR REFERENCE ONLY. ALL EQUIPMENT MUST MEET THE WRITTEN DESCRIPTION

OF THE SPECIFICATION, INCLUDING ALL REQUIRED ACCESSORIES, POWER

SUPPLIES, HARDWARE, ETC., REGARDLESS OF THE LISTED CATALOG NUMBER.

ERRORS IN THE CATALOG NUMBER DO NOT ALLEVIATE THE RESPONSIBILITY OF

PROVIDING THE PROPER EQUIPMENT REQUIRED FOR THE INSTALLATION AND

FIELD CONDITIONS. THE MATERIALS, PRODUCTS AND EQUIPMENT DESCRIBED IN

THE CONTRACT DOCUMENTS ESTABLISH A STANDARD OF QUALITY, FUNCTION,

DIMENSIONS AND APPEARANCE THAT MUST BE MET BY ANY PROPOSED

SUBSTITUTION.

EACH CONTRACTOR SHALL ASSUME RESPONSIBILITY FOR CONSTRUCTION

SAFETY AT ALL TIMES AND PROVIDE, AS PART OF CONTRACT, ALL TRENCH OR

BUILDING SHORING, SCAFFOLDING, SHIELDING, DUST/FUME PROTECTION,

MECHANICAL/ELECTRICAL PROTECTION, SPECIAL GROUNDING, SAFETY

RAILINGS, BARRIERS, AND OTHER SAFETY FEATURE REQUIRED TO PROVIDE

SAFE CONDITIONS FOR ALL WORKMEN AND SITE VISITORS.

IT IS THE CONTRACTOR'S RESPONSIBILITY TO KEEP CLEAN ALL EQUIPMENT AND

PLUMBING FIXTURES PROVIDED UNDER THIS CONTRACT FOR THE DURATION OF

THE PROJECT. EACH TRADE SHALL KEEP THE PREMISES FREE FROM AN

ACCUMULATION OF WASTE MATERIAL OR RUBBISH CAUSED BY THEIR

OPERATIONS. IN FACILITIES REQUIRING AN ENVIRONMENT OF EXTREME

CLEANLINESS, AND IT IS THE CONTRACTOR'S RESPONSIBILITY TO ADHERE TO

THE STRICT REGULATIONS REGARDING PROCEDURES ON THE EXISTING

PREMISES. AFTER ALL TESTS ARE MADE AND INSTALLATIONS COMPLETED

SATISFACTORILY. THOROUGHLY CLEAN ENTIRE INSTALLATION, BOTH EXPOSED

SURFACES AND INTERIORS. REMOVE ALL DEBRIS CAUSED BY WORK. REMOVE

TOOLS, SURPLUS, MATERIALS, WHEN WORK IS FINALLY ACCEPTED.

ALL FINISHED EQUIPMENT SURFACES DAMAGED DURING CONSTRUCTION SHALL

BE BROUGHT TO "AS NEW" CONDITION BY TOUCH UP OR REPAINTING. ANY RUST

SHALL BE REMOVED AND PRIMED PRIOR TO REPAINTING. TAKE ALL

NECESSARY PRECAUTIONS WITH EQUIPMENT, SYSTEMS AND BUILDING TO

PREVENT DAMAGE DUE TO FREEZING AND/OR WATER DAMAGE. REPAIR OR

REPLACE, AT NO CHANGE IN CONTRACT, ANY SUCH DAMAGE TO EQUIPMENT,

SYSTEMS AND BUILDING. PERFORM FIRST SEASONS WINTERIZING IN PRESENCE

OF OWNER'S OPERATING STAFF.

ALL PIPING AND FITTINGS USED ON THIS PROJECT SHALL BE NEW AND MARKED

WITH MANUFACTURER'S NAME AND SHALL COMPLY WITH ALL APPLICABLE ASTM

AND ANSI STANDARDS. ALL PIPING SHALL BE LABELED AND INSULATED AS

NOTED.

NO PLUMBING EQUIPMENT SHALL BE HIDDEN OR COVERED UP PRIOR TO

INSPECTION BY THE ENGINEER AND OWNER'S REPRESENTATIVE. ALL WORK THAT

IS DETERMINED TO BE UNSATISFACTORY SHALL BE CORRECTED IMMEDIATELY

AT NO ADDITIONAL COST. CONCEAL ALL CONTRACT WORK ABOVE CEILINGS

AND IN WALLS, BELOW SLABS, AND ELSEWHERE THROUGHOUT BUILDING. IF

CONCEALMENT IS IMPOSSIBLE OR IMPRACTICAL, NOTIFY ENGINEER AND

OWNER'S REPRESENTATIVE BEFORE STARTING THAT PART OF THE WORK AND

INSTALL ONLY AFTER THEIR APPROVAL. IN AREAS WITH NO CEILINGS, INSTALL

ONLY AFTER ENGINEER AND OWNER'S REPRESENTATIVE REVIEWS AND

COMMENTS ON ARRANGEMENT AND APPEARANCE.

BEFORE ACCEPTANCE OF THE WORK, FURNISH NECESSARY SKILLED LABOR TO

OPERATE ALL SYSTEMS BY SEASONS. INSTRUCT THE OWNER'S DESIGNATED

PERSONNEL ON THE PROPER OPERATION AND MAINTENANCE OF SYSTEMS AND

EQUIPMENT. OBTAIN WRITTEN ACKNOWLEDGMENT FROM PERSON INSTRUCTED

PRIOR TO ACCEPTANCE REPEAT THE INSTRUCTIONS IF ASKED TO DO SO.

CONTRACTOR IS FULLY RESPONSIBLE FOR SYSTEMS UNTIL ACCEPTANCE, EVEN

THOUGH OPERATED BY OWNER'S PERSONNEL, UNLESS OTHERWISE AGREED IN

WRITING. PROVIDE OPERATING, MAINTENANCE AND STARTING PRECAUTIONS

AND PROCEDURES TO BE FOLLOWED BY THE OWNER FOR OPERATING

SYSTEMS AND EQUIPMENT. MOUNT THE INSTRUCTION IN CLEAR PLASTIC HOLDER

ON OR ADJACENT TO THE EQUIPMENT.

FIRE-STOPPING FOR OPENINGS THROUGH FIRE AND SMOKE RATED WALL AND

FLOOR ASSEMBLIES: PROVIDE MATERIALS AND PRODUCTS LISTED OR

CLASSIFIED BY AN APPROVED INDEPENDENT TESTING LABORATORY FOR

"THROUGH-PENETRATION FIRE-STOP SYSTEMS." THE SYSTEM SHALL MEET THE

REQUIREMENTS OF "FIRE TESTS OF "THROUGH-PENETRATION FIRE-STOPS"

DESIGNATED ASTM E814. PROVIDE FIRE-STOP SYSTEM SEALS AT ALL

LOCATIONS WHERE PIPING, TUBING, CONDUIT, ELECTRICAL

BUSWAYS/CABLES/WIRES, DUCTWORK AND SIMILAR UTILITIES PASS THROUGH OR

PENETRATE FIRE RATED WALL OR FLOOR ASSEMBLY. PROVIDE FIRE-STOP

SEAL BETWEEN SLEEVE AND WALL FOR DRYWALL CONSTRUCTION. THE MINIMUM

REQUIRED FIRE RESISTANCE RATINGS OF THE WALL OR FLOOR ASSEMBLY

SHALL BE MAINTAINED BY THE FIRE-STOP SYSTEM. THE INSTALLATION SHALL

PROVIDE AN AIR AND WATERTIGHT SEAL. THE METHODS USED SHALL

INCORPORATE QUALITIES, WHICH PERMIT THE EASY REMOVAL OR ADDITION OF

ELECTRICAL CONDUITS OR CABLES WITHOUT DRILLING OR USE OF SPECIAL

TOOLS. THE PRODUCT SHALL ADHERE TO ITSELF TO ALLOW REPAIRS TO BE

MADE WITH THE SAME MATERIAL AND PERMIT THE VIBRATION, EXPANSION

AND/OR CONTRACTION OF ANY ITEMS PASSING THROUGH THE PENETRATION

WITHOUT CRACKING, CRUMBLING AND RESULTING REDUCTION IN FIRE RATING.

PROVIDE ALL REQUIRED SUPPORTS, BEAMS, ANGLES, HANGERS, RODS,

BASES, BRACES, AND OTHER ITEMS TO PROPERLY SUPPORT CONTRACT

WORK. SUPPORTS SHALL MEET THE APPROVAL OF THE ENGINEER AND

OWNER'S REPRESENTATIVE. MODIFY STUDS, ADD STUDS, ADD FRAMING, OR

OTHERWISE REINFORCE STUDS IN METAL STUD WALLS AND PARTITIONS AS

REQUIRED TO SUIT CONTRACT WORK. IF NECESSARY, IN STUD WALLS, PROVIDE

SPECIAL SUPPORTS FROM FLOOR TO STRUCTURE ABOVE. FOR PRECAST

PANELS/PLANKS AND METAL DECKS, SUPPORT MECHANICAL/ELECTRICAL

WORK AS DETERMINED BY MANUFACTURER, ENGINEER, AND OWNER'S

REPRESENTATIVE. PROVIDE HEAVY GAUGE STEEL MOUNTING PLATES FOR

MOUNTING CONTRACT WORK. MOUNTING PLATES SHALL SPAN TWO OR MORE

STUDS. SIZE, GAUGE, AND STRENGTH OF MOUNTING PLATES SHALL BE

SUFFICIENT FOR EQUIPMENT SIZE, WEIGHT, AND DESIRED RIGIDITY.

PIPING SHALL NOT BE SUPPORTED BY WIRES, BAND IRON, CHAINS, OR FROM

OTHER PIPING OR DUCT WORK, NOR BY VERTICAL EXPANSION BOLTS.

SUPPORT PIPING WITH INDIVIDUAL HANGERS FROM CONCRETE INSERTS,

WELDED SUPPORTS, OR BEAM CLAMPS OF PROPER CONFIGURATION AND

LOADING DESIGN REQUIREMENTS FOR EACH LOCATION; REPLACE IF NOT

SUITABLE. FOLLOW MANUFACTURER'S SAFE LOADING RECOMMENDATIONS.

SUSPEND WITH RODS OF SUFFICIENT LENGTH FOR SWING, USING PROPER

DIAMETER ROD FOR PIPE SIZE. PROVIDE ADDITIONAL STRUCTURAL STEEL

MEMBERS, HAVING ONE COAT RUSTPROOF PAINT, WHERE REQUIRED FOR

PROPER SUPPORT. PROVIDE OVERSIZED HANGERS WHERE

INSULATION/SUPPORTS MUST PASS BETWEEN PIPE AND HANGER. PROVIDE

CONTINUOUS SUPPORT OR EXTRA SUPPORTS FOR PLASTIC PIPE PER

MANUFACTURER'S REQUIREMENTS. HANGERS, WHEN ATTACHED TO JOISTS,

SHALL ONLY BE PLACED AT THE TOP OR BOTTOM CHORD PANEL POINT. ONLY

CONCENTRIC TYPE HANGERS ARE PERMISSIBLE; "C" TYPE NOT PERMITTED ON

JOISTS. PROVIDE RISER CLAMPS FOR EACH RISER AT EACH FLOOR. USE

TRAPEZE HANGERS WHERE A GROUP OF PIPING CAN BE INSTALLED.

PROVIDE COMPLETE PLUMBING CONNECTIONS TO ALL PLUMBING EQUIPMENT.

PROVIDE CONTROL CONNECTIONS TO EQUIPMENT WHERE INDICATED ON THE

DRAWINGS. PROVIDE VALVES ON PIPING AHEAD OF EACH PIECE OF

EQUIPMENT. PROVIDE ALL PIPING, TRIM, ACCESSORIES AND CONNECTIONS AS

REQUIRED FOR PROPER EQUIPMENT OPERATION OF EQUIPMENT PROVIDED BY

THIS CONTRACT, OWNER-FURNISHED EQUIPMENT AND EQUIPMENT FURNISHED BY

OTHER CONTRACTS. REFER TO MANUFACTURER'S DRAWINGS/SPECIFICATIONS

FOR REQUIREMENTS OF SPECIAL EQUIPMENT. VERIFY CONNECTION

REQUIREMENTS BEFORE BIDDING AND CONFIRM PRIOR TO ROUGHING.

PROVIDE ALL EXCAVATION AND BACKFILL, ROCK AND DEBRIS REMOVAL AND

RELATED WORK REQUIRED FOR ALL PLUMBING WORK.

TRENCH EXCAVATION: BY OPEN CUT, TO PROPER DEPTH AND GRADE NO

WIDER THAN REQUIRED FOR PLACEMENT OF WORK AND NOT MORE THAN 50

FT. IN ADVANCE OF UTILITY BEING INSTALLED. SHOULD TRENCH BOTTOM BE

WET, UNSTABLE, AND/OR OTHERWISE INCAPABLE OF SUPPORTING THE

CONTRACT WORK, IMMEDIATELY REPORT SAME TO OWNER'S REPRESENTATIVE.

SHOULD IT BE DEEMED UNSUITABLE, EXCAVATE TO DEPTH AS DIRECTED AND

BACKFILL WITH GRAVEL TO TRENCH DEPTH, OR PROVIDE CONCRETE

CRADLING. IN ADDITION TO GOVERNING CODES, PROTECT SIDES OF

EXCAVATIONS WITH SHEETING AND BRACING WHERE NECESSARY TO PREVENT

SLIDING OR CAVING OF BANKS AND TO PROTECT ADJACENT STRUCTURES.

REMOVE AS BACKFILL IS PLACED. PROVIDE AT LOCATIONS ADJACENT TO

EXISTING MANHOLES, HYDRANTS, AND SIMILAR ITEMS.

CUSHION AND BEDDING SAND: CLEAN, COARSE, FREE OF ORGANIC MATTER,

CONFORMING TO NEW YORK SATE DOT ITEM NO. 703-06. CRUSHED STONE:

CRUSHED STONE, GRADED, FREE OF ORGANIC MATERIALS, NO. 1 TO NO. 4

SIZE. CONFORMING TO NEW YORK STATE DOT ITEM NO. 703-0201. GRAVEL

FILL: WELL-GRADED NATURAL INORGANIC SAND AND GRAVEL CONFORMING

TO NEW YORK STATE DOT ITEM NO. 703-0202.

BEDDING: PROVIDE AROUND ALL PIPING WITH COARSE SAND FROM 6 IN.

BELOW TO 8 IN. ABOVE. APPLY BY HAND AND COMPACT UNDER AND AT

SIDES BY MECHANICAL MEANS. PIPING, JACKETS AND SAND BED MUST BE

INSPECTED AND TESTED PRIOR TO BACKFILL OF ANY NATURE. PROVIDE

NECESSARY ANCHORS, THRUST BLOCKS, FOR TESTING. FILL REMAINDER OF

TRENCH IN 12 IN. LAYERS, USE ORDINARY FILL MATERIAL, EXCEPT AS

OTHERWISE SPECIFIED. DO NOT USE FROZEN MATERIAL. REMOVE BOULDERS,

STONES, BROKEN ROCK, WOOD, BRICKS, BLOCKS, AND DEBRIS FROM FILL

MATERIAL BEFORE BACKFILL OPERATION. PROVIDE FINAL COMPACTION FOR

ALL TRENCHES BY MECHANICAL MEANS. USE MECHANICAL TAMPING

MACHINERY.

ORDINARY FILL: WELL-GRADED, NATURAL SOIL, MEETING THE FOLLOWING

REQUIREMENTS. FREE OF ORGANIC AND OTHER COMPRESSIBLE MATERIALS,

DEBRIS AND FROZEN MATERIALS, AND OF STONES LARGER THAN 4 IN.

MAXIMUM DIMENSION. BE OF SUCH NATURE AND CHARACTER THAT IT CAN BE

COMPACTED TO THE SPECIFIED DENSITIES. FREE OF ANY CLAY, HIGHLY

PLASTIC CLAYS, OF MATERIALS SUBJECT TO DECAY, DECOMPOSITION, OR

DISSOLUTION, AND OF CINDERS, ASH AND OTHER CORROSIVE MATERIALS.

FREE OF WOOD, STUMPS, ROOTS, ETC. MAXIMUM DRY DENSITY OF NOT LESS

THAN 115 LBS. PER CU. FT. MATERIAL FROM EXCAVATION ON THE SITE MAY BE

USED AS ORDINARY FILL IF IT MEETS THE ABOVE REQUIREMENTS.

BUILD LINES TO GRADE AND ELEVATIONS SHOWN. PROVIDE STAKES, GRADE

BOARDS, CLEATS, NAILS, INSTRUMENTS. LOCATE AND STAKE EACH NEW RUN

FOR ITS ENTIRE LENGTH. VERIFY ELEVATIONS GIVEN. START EACH

EXCAVATION AT LOW POINT. NOTIFY ENGINEER OF ELEVATION

DISCREPANCIES. PROTECT MARKS AND STATIONS. BEFORE STARTING

EXCAVATING WORK, COORDINATE WITH OWNER'S SITE REPRESENTATIVE AND

FURNISH SCHEDULE OF OPERATIONS TO OWNER. REMOVE MATERIALS

INCLUDING MASONRY WORK, RUBBLE, EARTH, BRICKWORK, CONCRETE, SAND,

DEBRIS, ABANDONED PIPE LINES, DRAINS AND SEWERS, ROCKS, BOULDERS,

AND CONCRETE, ALL OF WHICH IS CONSIDERED "EARTH EXCAVATION."

PROVIDE FOR LEGAL DISPOSITION OF EXCESS EXCAVATED MATERIALS. MAKE

ALLOWANCE FOR GRAVEL FILL, SAND BASES, THRUST BLOCKS, SHEET PIPING,

DRAINAGE PUMPS, AND WORK SPACE. START EXCAVATION AT ROUGH GRADE

AND PROVIDE FORM WORK AND SHEET PILING WHERE REQUIRED.

NATURAL GAS PIPING SHALL BE SCHEDULE 40 BLACK STEEL, WELDED

CONNECTIONS AND FITTINGS FOR PIPE SIZES LARGER THAN 21/2'', THREADED

AND SCREWED FITTINGS FOR PIPE SIZES 2'' AND SMALLER (USE TEFLON TAPE

FOR ALL THREADED CONNECTIONS). UNDERGROUND NATURAL GAS PIPING

SHALL BE SDR11 POLYETHYLENE TUBING WITH FUSION WELDED JOINTS AND

FITTINGS. TUBING SHALL BE VISIBLY MARKED FOR USE IN BURIED NATURAL

GAS SYSTEMS AND CONTAIN LOCATING WIRING. PROVIDE ALL NATURAL GAS

SYSTEMS IN COMPLIANCE WITH 2015 INTERNATIONAL FUEL GAS CODE AND

NYSEG REQUIREMENTS.

ACCURATELY ESTABLISH GRADE AND ELEVATION OF PIPING BEFORE SETTING

SLEEVES. INSTALL PIPING WITHOUT SPRINGING OR FORCING (EXCEPT WHERE

SPECIFICALLY CALLED FOR), MAKING PROPER ALLOWANCE FOR EXPANSION

AND ANCHORING. ARRANGE PIPING AT EQUIPMENT WITH NECESSARY OFFSETS,

UNIONS, FLANGES, AND VALVES, TO ALLOW FOR EASY PART REMOVAL AND

MAINTENANCE. OFFSET PIPING AND CHANGE ELEVATION AS REQUIRED TO

COORDINATE WITH OTHER WORK. AVOID CONTACT WITH OTHER MECHANICAL

OR ELECTRICAL SYSTEMS. PROVIDE ADEQUATE MEANS OF DRAINING AND

VENTING UNITS, RISERS, CIRCUITS AND SYSTEMS. CONCEAL PIPING UNLESS

OTHERWISE CALLED FOR. REAM PIPES AFTER CUTTING AND CLEAN BEFORE

INSTALLING. CAP OR PLUG EQUIPMENT AND PIPE OPENINGS DURING

CONSTRUCTION. INSTALL PIPING PARALLEL WITH LINES OF BUILDING,

PROPERLY SPACED TO PROVIDE CLEARANCE FOR INSULATION. MAKE

CHANGES IN DIRECTION AND BRANCH CONNECTIONS WITH FITTINGS. DO NOT

INSTALL VALVES, UNIONS AND FLANGES IN INACCESSIBLE LOCATIONS.

MATERIALS WITHIN A SYSTEM AND BETWEEN SYSTEMS SHALL BE CONSISTENT.

IF THIS IS NOT POSSIBLE, INSTALL DIELECTRIC FITTINGS.

PROVIDE ALL HANGERS AND SUPPORTS FOR PIPING IN ACCORDANCE WITH

THE 2015 INTERNATIONAL PLUMBING CODE.

NATURAL GAS VALVES: BRONZE BODY, SCREWED ENDS, AGA APPROVED AND

UL LISTED. MILWAUKEE BB2-100.

LABEL ALL PLUMBING PIPING ON PROJECT WITH ACRYLIC WRAP-AROUND

LABELS WITH FLOW ARROWS. LABEL PIPING EVERY 20'-0'' O.C. AND ON BOTH

SIDES OF WALL AND FLOOR PENETRATIONS.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

PLUMBING SPECIFICATIONS

13.

14.

15.

16.

17.

18.

19.

20.

21.

22.

23.

24.

25.

26.

PLUMBING CONTRACTOR SHALL REQUEST A COMPLETE SET OF BID

DOCUMENTS (DRAWINGS AND SPECIFICATIONS) INCLUDING BUT NOT LIMITED

TO, ARCHITECTURAL, STRUCTURAL, MECHANICAL, ELECTRICAL, CIVIL, FIRE

PROTECTION, ETC. FOR BIDDING AND COORDINATION PURPOSES.

INCLUDE IN PLUMBING BID ALL LABOR, MATERIALS, TOOLS, PLANT,

TRANSPORTATION, EXCAVATION, EQUIPMENT, INSURANCE, TEMPORARY

PROTECTION, PERMITS, INSPECTIONS, TAXES AND ALL NECESSARY AND

RELATED ITEMS REQUIRED TO PROVIDE COMPLETE AND OPERATIONAL

PLUMBING SYSTEMS SHOWN AND DESCRIBED. PROVIDE ALL SCAFFOLDING,

RIGGING, HOISTING AND SERVICES NECESSARY FOR ERECTION AND

DELIVERY OF EQUIPMENT AND APPARATUS FURNISHED INTO THE PREMISES.

THESE ITEMS SHALL BE REMOVED FROM PREMISES WHEN NO LONGER

REQUIRED.

REFERENCES TO CODES AND STANDARDS CALLED FOR IN THE CONTRACT

DOCUMENTS MEAN THE LATEST EDITION, AMENDMENT AND REVISIONS TO

THE CODES AND STANDARDS IN EFFECT ON THE DATE OF THESE

CONTRACT DOCUMENTS, UNLESS OTHERWISE NOTED.

THE DRAWINGS ARE DIAGRAMMATIC. DRAWINGS SHOW APPROXIMATE

LOCATIONS OF EQUIPMENT, AND FIXTURES. COORDINATE ALL PLUMBING

AND SYSTEMS, EQUIPMENT, AND MATERIALS INSTALLATION WITH ALL OTHER

BUILDING COMPONENTS. THE PLUMBING CONTRACTOR SHALL BE

RESPONSIBLE FOR ANY CHANGES IN OPENINGS AND LOCATIONS

NECESSITATED BY THE EQUIPMENT INSTALLED. THE ARCHITECTURAL

DRAWINGS SHALL INDICATE THE PLACEMENT OF ALL WALL AND CEILING

MOUNTED PLUMBING EQUIPMENT AND DEVICES IN ALL ROOMS WITH THE

EXCEPTION OF MECHANICAL AND ELECTRICAL EQUIPMENT ROOMS. EXACT

LOCATIONS ARE SUBJECT TO THE APPROVAL OF THE ENGINEER AND

OWNER'S REPRESENTATIVE.

DUE TO THE SMALL SCALE OF THE DRAWINGS, IT IS NOT POSSIBLE TO

INDICATE ALL OFFSETS, FITTINGS, CHANGES IN ELEVATION, ETC. VERIFY

FINAL LOCATIONS FOR ROUGH-INS WITH FIELD MEASUREMENTS AND WITH

THE EQUIPMENT BEING CONNECTED. VERIFY EXACT LOCATION AND

ELEVATIONS AT WORK SITE PRIOR TO ANY ROUGH IN WORK. DO NOT

SCALE PLANS. IF FIELD CONDITIONS, DETAILS, CHANGES IN EQUIPMENT OR

SUBMITTAL INFORMATION REQUIRE A SIGNIFICANT CHANGE TO THE

ORIGINAL DOCUMENTS, CONTACT THE ENGINEER AND OWNER'S

REPRESENTATIVE FOR APPROVAL BEFORE PROCEEDING. COORDINATE

WORK WITH OTHER TRADES AND DETERMINE EXACT ROUTING OF ALL

DUCT, PIPE, CONDUIT, ETC., BEFORE FABRICATION AND INSTALLATION.

ARRANGE FOR ALL CHASES, SLOTS AND OPENINGS IN OTHER BUILDING

COMPONENTS THAT ARE NOT INDICATED ON DRAWINGS, TO ALLOW FOR

PLUMBING INSTALLATIONS. COORDINATE WITH ARCHITECTURAL DRAWINGS.

VERIFY WITH ENGINEER AND OWNER'S REPRESENTATIVE EXACT LOCATION

OF ALL EQUIPMENT IN FINISHED AREAS, SUCH AS THERMOSTATS, FIXTURE

AND SWITCH MOUNTING HEIGHTS, AND EQUIPMENT MOUNTING HEIGHTS.

PROVIDE ALL NECESSARY PIPING, CONNECTIONS, ACCESSORIES,

SUPPORTS, HANGERS, ANCHORS, WIRING AND CONTROLS FOR COMPLETE

AND FUNCTIONAL INSTALLATION OF ALL THE ITEMS PROVIDED UNDER THIS

CONTRACT.

PROVIDE ALL REQUIRED EXCAVATION, BACKFILL AND COMPACTION FOR

UNDERGROUND WORK.

SLEEVE ALL PENETRATIONS THROUGH OUTSIDE OR FOUNDATION WALLS

WATERTIGHT.

FIRESTOP ALL PENETRATIONS THROUGH FIRE RATED ASSEMBLIES. REFER

TO ARCHITECTURAL DRAWINGS FOR LOCATIONS AND RATING OF ALL FIRE

RATED ASSEMBLIES.

FIELD VERIFY EXACT LOCATION, COMPOSITION AND CONDITION OF ALL

SITE PIPING, VALVES AND SYSTEMS AS REQUIRED FOR WORK OF THE

CONTRACT.

A.

B.

C.

D.

E.

F.

G.

H.

I.

J.

PLUMBING GENERAL NOTES

Revision Schedule

NO. DESC. DATE

1 PANEL SCHEDULE 2/4/2020

2 EP1 SCHEDULE 2/6/2020

3 OWNER REQUESTED

CHANGES

2/24/2020

4 UTILITY ADDITIONS 8/20/2020

TOTAL EST. DEMAND: 0 A

TOTAL CONN.: 0 A

TOTAL EST. DEMAND: 0 VA

TOTAL CONN. LOAD: 0 VA

LOAD CLASSIFICATION CONNECTED LOAD DEMAND FACTOR ESTIMATED DEMAND PANEL TOTALS

TOTAL AMPS: 112667 A 112667 A 112667 A

TOTAL LOAD: 13520000... 13520000 VA 13520000...

11 SPACE -- -- 0 0 -- -- SPACE 12

9 SPACE -- -- 0 0 -- -- SPACE 10

7 SPACE -- -- 0 0 -- -- SPACE 8

5 0 13520 6

3 0 13520 4

LVP1 200 A 3

0 13520

3 100 A ATS-1

CKT CIRCUIT DESCRIPTION TRIP POLES A (kVA) B (kVA) C (kVA) POLES TRIP CIRCUIT DESCRIPTION CKT

NOTES: PANELBOARD IS EXISTING. PROVIDE (1) NEW 100A/3P CIRCUIT BREAKER TO MATCH PANEL CONSTRUCTION.

MDP EAST GREENHOUSE 1 400 A 3Ø, 4W 120/208 WYE SURFACE 25kA I-LINE TYPE 1

MCB MLO

NAME LOCATION SOURCE

RATING (AMPS)

PHASE/WIRE VOLTAGE MOUNTING KAIC DESIGN MAKE NEMA TYPE

HINGED TRIM 200% NEUTRAL SUB-FEED LUGS SPD SIZE:PANELBOARD SCHEDULE SE RATED SUB-FEED BREAKER FEED-THRU LUGS INTEGRAL SPD

LIGHT FIXTURE SCHEDULE

TYPE DESCRIPTION LUMENS LAMP VOLTAGE

DESIGN MAKE ACCEPTABLE

MANUFACTURERMANUFACTURER MODEL NO.

EM1 WALL MOUNTED, LED, TWO-HEAD EMERGENCY BATTERY PACK WITH SELF DIAGNOSTICS AND TESTING. SUITABLE

FOR DAMP LOCATIONS.

650 EACH HEAD (2) 6 WATT LED EA 120 ISOLITE LIGHTING BUG6W WH MTB SD APPROVED EQUAL

X1 SINGLE FACED UNIVERSAL MOUNT LED EXIT SIGN WITH WHITE THERMOPLASTIC HOUSING, RED LETTERS, AND

REMOVABLE CHEVRONS

- 2.76 WATT LED 120 ISOLITE LIGHTING RL-AC-R-U-WH-MTEBP APPROVED EQUAL

X2 SINGLE FACED UNIVERSAL MOUNT LED EXIT SIGN AND EMERGENCY BATTERY PACK COMBINATION UNIT WITH WHITE

HOUSING, RED LETTERS, REMOVABLE CHEVRONS, AND NI-CAD BATTERY AND SELF DIAGNOSICS

125 EACH HEAD 2.76 WATT LED 120 ISOLITE LIGHTING RLC-LED-R-U-WH-MTEB APPROVED EQUAL

KM2

Text Box

AS-BUILTS

ChrisM.Wilson Typewritten Text 5 USDA Notes on As-Builts 09/24/2020 (CMW/EPM)