2.01 RFP SPRMM126RRA08.pdf

CAUTION TO OFFERORS - NO CONTRACT WILL BE AWARDED UNDER

THIS SOLICITATION AT GREATER THAN FAIR AND REASONABLE PRICES.

SECTION A - COVER SHEET

(See Section L of the Table of Contents in

You are cautioned to note the "Certification of Non-Segregated Facilities" in the solicitation. Failure to agree to the certification will render your reply nonresponsive to the terms of solicitations involving awards of contracts exceeding $25,000 which are not exempt from the provisions of the Equal Opportunity clause.

"Fill-ins" are provided on the face and reverse of Standard Form 18 and Parts I and IV of Standard Form 33, or other solicitation documents and Sections of Table of Contents in this solicitation and should be examined for applicability.

See the provision of this solicitation entitled "Late Bids, Modifications of Bids or Withdrawal of Bids" or "Late Proposals, Modifications of Proposals and Withdrawals of Proposals."

When submitting your reply,the envelope used must be plainly marked with the Solicitation Number, as shown above and the date and local time set forth for bid opening or receipt of proposals in the solicitation document.

If NO RESPONSE is to be submitted, detach this sheet from the solicitation, complete the information requested on reverse,fold, affix postage, and mail. NO ENVELOPE IS NECESSARY.

Replies must set forth full, accurate, and complete information as required by this solicitation The penalty for making false statements is prescribed in 18 U.S.C.1001.

(X one).

a. SEALED BID

c. NEGOTIATED (RFQ)

INSTRUCTIONS

NOTE THE AFFIRMATIVE ACTION REQUIREMENT OF THE EQUAL OPPORTUNITY CLAUSE WHICH MAY APPLY TO THE CONTRACT

RESULTING FROM THIS SOLICITATION.

3. ISSUING OFFICE

(including attachments).

4. ITEMS TO BE PURCHASED

5 PROCUREMENT INFORMATION

a. THIS PROCUREMENT IS UNRESTRICTED

b. THIS PROCUREMENT IS A ______% SET-ASIDE FOR ONE OF THE FOLLOWING

1. SOLICITATION NUMBER

INFORMATION TO OFFERORS OR QUOTERS

6. ADDITIONAL INFORMATION

(1) Small Business (2) Labor Surplus Area Concerns (3) Combined Small Business/Labor Area Concerns

DD Form 1707, MAR 89 Previous editions are obsolete.

(Brief description)

(Complete mailing address, including Zip Code)

(X one) this solicitation for details of the set-aside.)

(X and complete as applicable)

461/089

2.

b. NEGOTIATED (RFP)

7. POINT OF CONTACT FOR INFORMATION

a. NAME (Last, First, Middle Initial) b. ADDRESS (Include Zip Code)

c. TELEPHONE NUMBER (Include Area Code and Extension) (NO COLLECT CALLS)

SPRMM1-26-R-RA08

X

25198-0080 (IDIQ T)

SPRMM1 DLA MECHANICSBURG

DLR PROCUREMENT OPS DSCC-ZI COC W5

P. O. BOX 2020, 5450 CARLISLE PIKE

MECHANICSBURG PA 17055-0788

SEE SCHEDULE

X

S. MCDONNELL ZIL1

SPRMM1 DLA MECHANICSBURG

( ) - MECHANICSBURG PA 17055-0788

KKKKKKKKKKKKKKKKKKKJ

KKKKKKKKKKKKKKKKKKKJ

e. OTHER

8. REASONS FOR NO RESPONSE

DD Form 1707 Reverse, MAR 89

(1) Typed or Printed Name

d. DO NOT REGULARLY MANUFACTURE OR SELL THE TYPE OF ITEMS INVOLVED

b. CANNOT MEET DELIVERY REQUIREMENT

c. UNABLE TO IDENTIFY THE ITEM(S)

a. CANNOT COMPLY WITH SPECIFICATIONS

9. MAILING LIST INFORMATION

WE DESIRE TO BE RETAINED ON THE MAILING LIST FOR FUTURE PROCUREMENT OF THE TYPE OF ITEM(S) INVOLVEDYES NO

10. RESPONDING FIRM

a. COMPANY NAME b. ADDRESS

c. ACTION OFFICER

(4) Date Signed

AFFIX

STAMP

HERE

(X all that apply)

FROM

DATE (YYMMDD)

SOLICITATION NUMBER

LOCAL TIME TO

(Last, First, Middle Initial) (YYMMDD)

(2) Title (3) Signature

FOLDFOLD

FOLD FOLD

(Specify)

(X one)

(INCLUDE ZIP CODE)

SPRMM1-26-R-RA08

03:00 P.M.227 FEB 2026

SOLICITATION, OFFER AND AWARD

2. CONTRACT NUMBER

PAGE OF PAGES

1 64

6. REQUISITION/PURCHASE NUMBER

7. ISSUED BY

CODE

8. ADDRESS OFFER TO (If other than item 7)

25198-0080

DLA WEAPONS SUPPORT - MECHANICSBURG

DLA PROCUREMENT OPS DLA - ZI

DLA MECHANICSBURG - CODE ZIL1

P.O. 2020, 5450 CARLISLE PIKE

MECHANICSBURG, PA 17055-0788

NOTE: In sealed bid solicitations "offer" and "offeror" mean "bid" and "bidder".

SOLICITATION

9. Sealed offers in original and copies for furnishings the supplies or services in the Schedule will be received at the place specified in item 8, or if hand carried, in the depository located in BLDG. 203, NORTH END, CODE ZIL1 until 5:00 PM local time 2/27/2026 (Hour) (Date)

CAUTION - LATE Submissions, Modifications, and Withdrawals: See Section L, Provision No. 52.214-7 or 52.215-1. All offers are subject to all terms and conditions contained in this solicitation.

10. FOR

INFORMATION

CALL:

A. NAME

SEAN MCDONNELL

B. TELEPHONE (NO COLLECT CALLS) C. E-MAIL ADDRESS

sean.mcdonnell@dla.mil

AREA CODE

NUMBER

EXTENSION

11. TABLE OF CONTENTS

(X) SEC. DESCRIPTION PAGE(S) (X) SEC. DESCRIPTION PAGE(S)

PART I - THE SCHEDULE PART II - CONTRACT CLAUSES

A SOLICITATION/CONTRACT FORM 1 I CONTRACT CLAUSES 25

B SUPPLIES OR SERVICES AND PRICES/COSTS 3 PART III - LIST OF DOCUMENTS, EXHIBITS AND OTHER ATTACH.

C DESCRIPTION/SPECS./WORK STATEMENT 4-5 J LIST OF ATTACHMENTS 42

D PACKAGING AND MARKING 10-19 PART IV - REPRESENTATIONS AND INSTRUCTIONS

E INSPECTION AND ACCEPTANCE 20

K REPRESENTATIONS, CERTIFICATIONS AND OTHER

STATEMENTS OF OFFERORS 43

F DELIVERIES OR PERFORMANCE 21

G CONTRACT ADMINISTRATION DATA 23-25 L INSTRUCTIONS, CONDITIONS, AND NOTICES TO OFFERORS 60

H SPECIAL CONTRACT REQUIREMENTS 25 M EVALUATION FACTORS FOR AWARD 62

OFFER (Must be fully completed by offeror) NOTE: Item 12 does not apply if the solicitation includes the provisions at 52.214-16, Minimum Bid Acceptance Period.

12. In compliance with the above, the undersigned agrees, if this offer is accepted within calendar days (60 calendar days unless a different period is inserted by the offeror) from the date for receipt of offers specified above, to furnish any or all items upon which prices are offered at the set opposite each item, delivered at the designated point(s), within the time specified in the schedule.

13. DISCOUNT FOR PROMPT PAYMENT

(See Section I, Clause No. 52.232-8)

10 CALENDAR DAYS (%) 20 CALENDAR DAYS (%) 30 CALENDAR DAYS (%) CALENDAR DAYS(%)

14. ACKNOWLEDGMENT OF AMENDMENTS

(The offeror acknowledges receipt of amendments to the SOLICITATION for offerors and related documents numbered and dated):

AMENDMENT NO. DATE AMENDMENT NO. DATE

15A. NAME AND

ADDRESS

OF OFFEROR

CODE FACILITY 16. NAME AND THE TITLE OF PERSON AUTHORIZED TO SIGN

OFFER(Type or print)

15B. TELEPHONE NUMBER 15C. CHECK IF REMITTANCE ADDRESS IS

DIFFERENT FROM ABOVE - ENTER SUCH

ADDRESS IN SCHEDULE.

17. SIGNATURE 18. OFFER DATE

AREA CODE NUMBER EXTENSION

AWARD (To be completed by Government)

19. ACCEPTED AS TO ITEMS NUMBERED 20. AMOUNT 21. ACCOUNTING AND APPROPRIATION

22. AUTHORITY FOR USING OTHER THAN FULL OPEN COMPETITION:

10 U.S.C. 2304 (c) 41 U.S.C. 3304(a) ( )

23. SUBMIT INVOICES TO ADDRESS SHOWN IN ITEM

(4 copies unless otherwise specified)

24. ADMINISTERED BY (If other than Item 7) 25. PAYMENT WILL BE MADE BY CODE

26. NAME OF CONTRACTING OFFICER (Type or print) 27. UNITED STATES OF AMERICA

(Signature of Contracting Officer)

28. AWARD DATE

IMPORTANT - Award will be made on this Form, or on Standard Form 26, or by other authorized official written notice.

AUTHORIZED FOR LOCAL REPRODUCTION

Previous edition is unusable

STANDARD FORM 33 (REV. 6/2014)

Prescribed by GSA - FAR (48 CFR) 53.214 (c)

SPRMM1

5. DATE ISSUED

1/26/2026

4. TYPE OF SOLICITATION

SEALED BID (IFB)

NEGOTIATED (RFP)

3. SOLICITATION NUMBER

SPRMM126RRA08

RATING

DO-A3

1. THIS CONTRACT IS A RATED ORDER

UNDER DPAS (15 CFR 700)

mailto:sean.mcdonnell@dla.mil

SPRMM126RRA08

(PLEASE NOTE THAT SECTIONS B THROUGH H MAY NOT BE IN ALPHABETICAL ORDER. PLEASE READ SOLICITATION

IN ITS ENTIRETY).

SECTION A

GENERAL INFORMATION FOR OFFERORS

1. The purpose of this solicitation is to establish an indefinite-delivery type contract for the supplies listed in Section B, that will provide stock coverage for customers both overseas and in the United States, including Alaska and Hawaii, and our possessions.

2. Under this solicitation, the resulting contract will be a Firm-Fixed-Price, Indefinite-Quantity Contract issued under FAR Part 15, with a 3-year base period and 2 one-year option periods. The total contract period will be five years. The terms “year” or “contract year,” as used in this solicitation, mean a period of 365 days beginning on the contract start date and every 365 days thereafter, except for a leap year, in which the contract year shall be 366 days.

3. The method used to place orders under this contract will be: Delivery Orders placed by DLA Weapons Support at Mechanicsburg (DLA-Mech). DLA-Mech will issue delivery orders with the awardee for the supplies cited in Section B. This contract is not obligating any funds. Funding will be provided on each delivery order placed under the contract.

4. The proposals received in response to this solicitation will be evaluated under Lowest Price Technically Acceptable “LPTA” procedures as described in Section M of this solicitation.

5. Please note that contractors shall complete all contractor required fill-ins and submit the pricing spreadsheet along with all pages of the solicitation to sean.mcdonnell@dla.mil, regardless of the number of CLINs that are proposed on. These sections are pertinent to understanding the requirements of the solicitation.

6. Some clauses/provisions may not appear in the correct section (D-M) due to system constraints.

7. NOTE TO POTENTIAL OFFERORS: Due to repetitive demands, the Government may place multiple awards.

Offers should be aware that the only guarantee upon award is for the contract minimum split equally among awardees.

8. Pursuant to FAR 16.504 (c)(1)(ii)(C), a single award will be made for the planned ID-IQs because: Only one contractor is capable of providing performance at the level of quality required because the supplies and services are unique or highly specialized. Spectral Labs Inc. is the Sole Source, Original Equipment Manufacturer (OEM) of the items and multiple awards would not be in the best interest of the Government.

CONTRACT MINIMUM VALUE – Qty 1 each CONTRACT MAXIMUM VALUE - $6,975,450.00 (calculated as 7.5 x ADV for each NSN) mailto:sean.mcdonnell@dla.mil

SECTION B – SCHEDULE OF SUPPLIES

1. This solicitation is for the acquisition of parts specified under Section B Spreadsheet information/ instructions below. Offerors shall provide their pricing in the Section B Pricing Spreadsheet found below.

2. Section B Spreadsheet Information/Instructions.

FSC NIIN Part Number Item Unit of Measure

6350 016903471 8602252 DETETCTOR SUPPORT EA

6120 016904087 8602255 PSMC ASSEMBLY EA

5980 016905244 8602261 DISPLAY ASSEMBLY EA

5998 016905248 8602246 CONTROL ASSEMBLY EA

5930 016905713 8602245 SWITCH ASSEMBLY EA

Place of Inspection Supplies & Packaging: Offeror fills in the CAGE code of the place of inspection for supplies and packaging. If locations are the same as offeror’s address, offeror can indicate “SAME”.

3. Section B – Pricing Spreadsheet

CLIN NSN ADQ Qty Ranges From

Qty Ranges To

Base Year 1

Base Year 2

Base Year 3

Option Year 1

Option Year 2

0001 6350 016903471 15 1 10

11 20

21 30

0002 6120 016904087 15 1 10

11 20

21 30

0003 5980 016905244 15 1 10

11 20

21 30

0004 5998 016905248 15 1 10

11 20

21 30

0005 5930 016905713 15 1 10

11 20

21 30

***NOTE: Basic drawing or specification indicating the item is manufactured by Government drawing or specification. The offeror upon completing pricing for this item, certifies that the item is manufactured IAW all drawing/specifications stated within the solicitation. This column gives only the basic drawing/specification number. See basic specification for basic secondary drawing information.

CLIN(s)/NSN: Self-Explanatory

ADQ: ADQ = Estimated Annual Demand Quantity

Quantity Ranges: Self-Explanatory

Year One – Year Five: Offeror should fill in the base year and each option year unit price for each quantity range.

For all CLINs the unit prices shall be priced as FOB Origin. Unit prices proposed should include all costs associated with providing the item in accordance with all terms and conditions stated in the solicitation and resultant contract.

SECTION D – PACKAGING AND MARKING

Packaging shall be in accordance with MIL-STD-2073 unless otherwise specified in the delivery order, as certain immediate use requirements may allow for commercial packaging in accordance with ASTM-D-3951 - Standard Practice for Commercial items.

The MIL-STD-2073 packaging shall be in conformance with the following Packaging Requirement Code (PRC) on page 2 of this solicitation.

NSN: 6350 016903471 PCK CTGY CD: ZZZ0

HM QUP ICQ PMT CD PM WM CUD CT UC LP IC UCL SP MK PACK UNIT PKWT

N 001 000 41 1 00 EA GE D ED A 00 B 00 EFF 9.5

UNIT PKCU OPI CAGE SPI NUMBER REV SPI DATE CONTAINER NSN

.145 O

NSN: 6120 016904087 PCK CTGY CD: ZZZ0

HM QUP ICQ PMT CD PM WM CUD CT UC LP IC UCL SP MK PACK UNIT PKWT

N 001 000 41 1 00 EA GE D ED A 00 B 00 EFF 3.5

UNIT PKCU OPI CAGE SPI NUMBER REV SPI DATE CONTAINER NSN

.290 O

NSN: 5980 016905244 PCK CTGY CD: ZZZ0

HM QUP ICQ PMT CD PM WM CUD CT UC LP IC UCL SP MK PACK UNIT PKWT

N 001 000 41 1 00 EA GE D ED A 00 B 00 EFF 3.1

UNIT PKCU OPI CAGE SPI NUMBER REV SPI DATE CONTAINER NSN

.257 O

NSN: 5998 016905248 PCK CTGY CD: ZZZ0

HM QUP ICQ PMT CD PM WM CUD CT UC LP IC UCL SP MK PACK UNIT PKWT

N 001 000 41 1 00 EA GE D ED A 00 B 00 EFF 2.2

UNIT PKCU OPI CAGE SPI NUMBER REV SPI DATE CONTAINER NSN

.223 O

NSN: 5930 016905713 PCK CTGY CD: ZZZ0

HM QUP ICQ PMT CD PM WM CUD CT UC LP IC UCL SP MK PACK UNIT PKWT

N 001 000 41 1 00 EA GE D ED A 00 B 00 EFF 3.1

UNIT PKCU OPI CAGE SPI NUMBER REV SPI DATE CONTAINER NSN

.233 O

SECTION E – INSPECTION & ACCEPTANCE

Please identify the following, if different from your facility/cage. If locations are the same as offeror’s address, offeror can indicate “SAME”.

CAGE for performance: ________________ CAGE for inspection: ________________ CAGE for acceptance: ________________

SECTION F – DELIVERIES OR PERFORMANCE

PLACE OF DELIVERY: The place of delivery for all items to be acquired hereunder will be specified in individual delivery orders issued under this Indefinite Delivery – Indefinite Quantity contract.

TIME OF DELIVERY:

Offeror's Proposed Delivery Time: ____ days

ACCELERATED DELIVERIES: Accelerated deliveries in advance of the specified delivery schedule are authorized. Any accelerated delivery will be at no additional expense to the Government, unless specifically authorized by the Procuring or Administrative Contracting Officer.

PARTIAL SHIPMENTS: Shipments of item quantities less than each line item quantity specified in the delivery order schedule are authorized. Multiple shipments to one destination are authorized. Any partial shipment will be at no additional expense to the Government, unless specifically authorized by the Procuring or Administrative Contracting Officer.

*NOTE - See Section I, FAR clause 52.216-18, Ordering

All contractual documents (i.e. contracts, purchase orders, task orders, delivery orders and modifications) related to the instant procurement are considered to be issued by the Government when copies are either deposited in the mail, transmitted by facsimile, or sent by other electronic commerce methods, such as email. The Government's acceptance of the contractor's proposal constitutes bilateral agreement to issue contractual documents as detailed herein.

SPRMM1-26-R-RA08 PAGE 6 OF 64

PART I - THE SCHEDULE

SECTION B

SUPPLIES OR SERVICES AND PRICES/COSTS

WSSTERMBZ04

IMPORTANT NOTICE REGARDING HAZARDOUS MATERIAL

FAR clause 52.223-3, Hazardous Material Identification and Material Safety Data, is incorporated by reference in Section I in this solicitation ad required offerors to--

(1) identify any hazardous material (defined in FED STD 313 as an item or chemical which is a "health or physical hazard" per OSHA in 29 CFR 1910.1200) that will be delivered under a resultant contract, and

(2) provide a Material Safety Data Sheet meeting OSHA/FED STD 313 requirements for all hazardous material identified.

While not an all-inclusive listing of hazardous material, at a minimum, any it em with a four-digit Federal Supply Code (FSC), which correlates to the first four positions of the National Stock Number (NSN), of 6810, 6820, 6830, 6840, 6850, 7930, 8010, 8030, 8040, 9110, 9135, 9140, 9150, or 9160 is considered hazardous material and requires submission of a Material Safety Data Sheet or an appropriate representation that there is no hazardous material contained in the item.

Failure to provide the required information and documentation may render you ineligible for award. If you have questions about whether a solicited item is classified as hazardous, contact the NAVSUP WSS HAZMAT point of contact, NAVSUP WSS Code 0772, at (717)605-1361. (10-06)

PART I - THE SCHEDULE

SECTION C

DESCRIPTION/SPECIFICATIONS/WORK STATEMENT

ACTIVITY USE ONLY: TDP VERSION NO.: 001NIIN: 016903471

ITEM NAME: DETECTOR SUPPORT AS

1. SCOPE

1.1 This contract/purchase order contains the requirements for manufacture and the contract quality requirements for the DETECTOR SUPPORT AS .

2. APPLICABLE DOCUMENTS

2.1 Applicable Documents - The document(s) listed below form a part of this contract/purchase order including modifications or exclusions.

2.1.1 "Document References" listed below must be obtained by the Contractor. Ordering information is included as an attachment to this contract/purchase order.

3. REQUIREMENTS

3.1 Cage Code/Reference Number Items - The DETECTOR SUPPORT AS furnished under this contract/purchase order shall be the design represented by Cage Code(s) reference number(s). Cage _______ ref. no.

<549W5 8602252>

3.2 Marking - This item shall be physically identified in accordance with <MIL-STD-130, REV N, 16 NOV 2012> .

3.3 Changes in Design, Material Servicing, or Part Number - Except for a Code 1 change, which shall be processed as provided in the code statement shown below, no substitution of items shall be made until the NAVICP-MECH Contracting Officer has notified and approval has been given by issuance of a written change order. When any change in design, material, servicing or part number is made to replace or substitute any item to be furnished on this contract/purchase order, the Contractor shall furnish, for the substituting/replacement item, a drawing and an explanation of the reason for the change, explaining the reason therefor. If finished detail drawings are not available, shop drawings in the form used by the manufacturer will be acceptable for Government evaluation. When notifying the Procurement Contracting Officer of the reasons for making substitutions, the type of change shall be indicated by code number in accordance with one of the following statements:

SPRMM1-26-R-RA08 PAGE 7 OF 64

Code 1: PART NUMBER CHANGE ONLY - If the Manufacturer's Part Number indicated thereon has changed, but the parts are identical in all respects, supply the item and advise NAVICP-MECH immediately of the new part number.

Code 2: Assembly (or set or kit) not furnished - Used following detail parts.

Code 3: Part not furnished separately - Use assembly.

Code 4: Part redesigned - Old and new parts are completely interchangeable.

Code 5: Part redesigned - New part replaces old. Old part cannot replace new.

Code 6: Part redesigned - Parts not interchangeable.

ACTIVITY USE ONLY: TDP VERSION NO.: 001NIIN: 016904087

ITEM NAME: PSMC ASSEMBLY

1. SCOPE

1.1 This contract/purchase order contains the requirements for manufacture and the contract quality requirements for the PSMC ASSEMBLY .

2. APPLICABLE DOCUMENTS

2.1 Applicable Documents - The document(s) listed below form a part of this contract/purchase order including modifications or exclusions.

2.1.1 "Document References" listed below must be obtained by the Contractor. Ordering information is included as an attachment to this contract/purchase order.

3. REQUIREMENTS

3.1 Cage Code/Reference Number Items - The PSMC ASSEMBLY furnished under this contract/purchase order shall be the design represented by Cage Code(s) reference number(s). Cage _______ ref. no.

<53711 8602255>

3.2 Marking - This item shall be physically identified in accordance with <MIL-STD-130, REV N, 16 NOV 2012> .

3.3 Changes in Design, Material Servicing, or Part Number - Except for a Code 1 change, which shall be processed as provided in the code statement shown below, no substitution of items shall be made until the NAVICP-MECH Contracting Officer has notified and approval has been given by issuance of a written change order. When any change in design, material, servicing or part number is made to replace or substitute any item to be furnished on this contract/purchase order, the Contractor shall furnish, for the substituting/replacement item, a drawing and an explanation of the reason for the change, explaining the reason therefor. If finished detail drawings are not available, shop drawings in the form used by the manufacturer will be acceptable for Government evaluation. When notifying the Procurement Contracting Officer of the reasons for making substitutions, the type of change shall be indicated by code number in accordance with one of the following statements:

Code 1: PART NUMBER CHANGE ONLY - If the Manufacturer's Part Number indicated thereon has changed, but the parts are identical in all respects, supply the item and advise NAVICP-MECH immediately of the new part number.

Code 2: Assembly (or set or kit) not furnished - Used following detail parts.

Code 3: Part not furnished separately - Use assembly.

Code 4: Part redesigned - Old and new parts are completely interchangeable.

Code 5: Part redesigned - New part replaces old. Old part cannot replace new.

Code 6: Part redesigned - Parts not interchangeable.

ACTIVITY USE ONLY: TDP VERSION NO.: 001NIIN: 016905244

ITEM NAME: ASSEMBLY, DISPLAY M

1. SCOPE

SPRMM1-26-R-RA08 PAGE 8 OF 64

1.1 This contract/purchase order contains the requirements for manufacture and the contract quality requirements for the ASSEMBLY, DISPLAY M .

2. APPLICABLE DOCUMENTS

2.1 Applicable Documents - The document(s) listed below form a part of this contract/purchase order including modifications or exclusions.

2.1.1 "Document References" listed below must be obtained by the Contractor. Ordering information is included as an attachment to this contract/purchase order.

3. REQUIREMENTS

3.1 Cage Code/Reference Number Items - The ASSEMBLY, DISPLAY M furnished under this contract/purchase order shall be the design represented by Cage Code(s) reference number(s). Cage _______ ref. no.

<549W5 8602261>

3.2 Marking - This item shall be physically identified in accordance with <MIL-STD-130, REV N, 16 NOV 2012> .

3.3 Changes in Design, Material Servicing, or Part Number - Except for a Code 1 change, which shall be processed as provided in the code statement shown below, no substitution of items shall be made until the NAVICP-MECH Contracting Officer has notified and approval has been given by issuance of a written change order. When any change in design, material, servicing or part number is made to replace or substitute any item to be furnished on this contract/purchase order, the Contractor shall furnish, for the substituting/replacement item, a drawing and an explanation of the reason for the change, explaining the reason therefor. If finished detail drawings are not available, shop drawings in the form used by the manufacturer will be acceptable for Government evaluation. When notifying the Procurement Contracting Officer of the reasons for making substitutions, the type of change shall be indicated by code number in accordance with one of the following statements:

Code 1: PART NUMBER CHANGE ONLY - If the Manufacturer's Part Number indicated thereon has changed, but the parts are identical in all respects, supply the item and advise NAVICP-MECH immediately of the new part number.

Code 2: Assembly (or set or kit) not furnished - Used following detail parts.

Code 3: Part not furnished separately - Use assembly.

Code 4: Part redesigned - Old and new parts are completely interchangeable.

Code 5: Part redesigned - New part replaces old. Old part cannot replace new.

Code 6: Part redesigned - Parts not interchangeable.

ACTIVITY USE ONLY: TDP VERSION NO.: 001NIIN: 016905713

ITEM NAME: ASSEMBLY, SWITCH MO

1. SCOPE

1.1 This contract/purchase order contains the requirements for manufacture and the contract quality requirements for the ASSEMBLY, SWITCH MO .

2. APPLICABLE DOCUMENTS

2.1 Applicable Documents - The document(s) listed below form a part of this contract/purchase order including modifications or exclusions.

2.1.1 "Document References" listed below must be obtained by the Contractor. Ordering information is included as an attachment to this contract/purchase order.

3. REQUIREMENTS

3.1 Cage Code/Reference Number Items - The ASSEMBLY, SWITCH MO furnished under this contract/purchase order shall be the design represented by Cage Code(s) reference number(s). Cage _______ ref. no.

<549W5 8602245>

3.2 Marking - This item shall be physically identified in accordance

SPRMM1-26-R-RA08 PAGE 9 OF 64

with <MIL-STD-130, REV N, 16 NOV 2012> .

3.3 Changes in Design, Material Servicing, or Part Number - Except for a Code 1 change, which shall be processed as provided in the code statement shown below, no substitution of items shall be made until the NAVICP-MECH Contracting Officer has notified and approval has been given by issuance of a written change order. When any change in design, material, servicing or part number is made to replace or substitute any item to be furnished on this contract/purchase order, the Contractor shall furnish, for the substituting/replacement item, a drawing and an explanation of the reason for the change, explaining the reason therefor. If finished detail drawings are not available, shop drawings in the form used by the manufacturer will be acceptable for Government evaluation. When notifying the Procurement Contracting Officer of the reasons for making substitutions, the type of change shall be indicated by code number in accordance with one of the following statements:

Code 1: PART NUMBER CHANGE ONLY - If the Manufacturer's Part Number indicated thereon has changed, but the parts are identical in all respects, supply the item and advise NAVICP-MECH immediately of the new part number.

Code 2: Assembly (or set or kit) not furnished - Used following detail parts.

Code 3: Part not furnished separately - Use assembly.

Code 4: Part redesigned - Old and new parts are completely interchangeable.

Code 5: Part redesigned - New part replaces old. Old part cannot replace new.

Code 6: Part redesigned - Parts not interchangeable.

WSSTERMCZ05

CONFIGURATION MANAGEMENT - MARITIME

1.0 Configuration Management

1.1 The cognizant systems command (SYSCOM), Naval Sea Systems Command (NAVSEA) or Naval Information Warfare Systems Command (NAVWAR), Program Manager will maintain configuration control and change authority for all items in this contract.

1.2 In accordance with the configuration management provisions of this contract, the Contractor must maintain the total Equipment baseline configuration of the parts on this contract including, but not limited to, hardware, software and firmware.

NOTE: The latest revisions of the DOD Forms referenced in this term can be found at https://www.esd.whs.mil/dd. The latest revisions of the DIDs referenced in this term can be found at https://quicksearch.dla.mil/.

2.0 Engineering Changes

2.1 The Government will not be responsible for any contract delay or disruption or any increased costs of performance of the Contractor due to a misclassification of an Engineering Change Proposal (ECP) by the Contractor, including those costs associated with replacement of delivered items resulting from such a misclassification. ECP's are classified as either Class I (Major) or Class II (Minor). For detailed classification criteria refer to DD Form 1692 instructions sheet. ECPs must be prepared in accordance with DI-SESS-80639E, Engineering Change Proposal (ECP).

NOTE: Any ECP or notification of an ECP submitted to the PCO in accordance with this paragraph must also be copied to the NAVSUP WSS CM Team at usn.philadelphia.navsupwssphil.mbx.configuration-management@us.navy.mil.

2.1.1 Class I (Major) Changes: The Contractor must coordinate with the cognizant SYSCOM Program Office prior to any Class I ECP submission. The Contractor must notify the Procurement Contracting Officer (PCO) of any pending or approved Class I engineering changes with another Government activity that the Contractor proposes to incorporate under this contract. The cognizant SYSCOM Program Office will approve or disapprove of Class I changes. Any approved Class I change may necessitate contract changes by the PCO, which changes may be handled under the Changes clause of this contract, FAR 52.243-1 The Contractor must not implement a Class I change on this contract until a contract modification is issued by the PCO.

2.1.2 Class II (Minor) Changes: Class II changes must be submitted to the cognizant Defense Contract Management Agency (DCMA) Contract Management Office (CMO), or to the Supervisor of Shipbuilding (SUPSHIP) Groton, for concurrence in classification and may be implemented only upon receiving DCMA, SUPSHIP, or NAVSEA/NAVWAR Technical Warrant Holder (TWH) concurrence. On Navy Special Emphasis Program contracts/purchase orders, the Contractor must submit the Class II (Minor) change to the PCO for approval or disapproval. Class II changes must be made at no additional cost to the Government.

SPRMM1-26-R-RA08 PAGE 10 OF 64

WSSTERMCZ05 (CONT)

CONFIGURATION MANAGEMENT - MARITIME

2.2 The Contractor is not entitled to any equitable adjustment to the contract price or terms based on the Government's disapproval of a Class I or Class II ECP.

3.0 Variances

3.1 The Contractor must not deliver any item for acceptance by the Government that incorporates a known departure from product definition information unless a Request for Variance (RFV) has been approved. Authorized variances are a temporary departure from the requirements only and do not authorize a change to the item's configuration baseline.

RFVs are classified as Critical, Major, or Minor. For detailed classification criteria refer to the DD Form 1694 instructions sheet. Variance requests must be prepared in accordance with DI-SESS-80640E - Request for Variance

(RFV).

NOTE: Any RFV submitted to the PCO in accordance with this paragraph must also be copied to the NAVSUP WSS RFV Review Team at usn.philadelphia.navsupwssphil.mbx.rfv-review-team@us.navy.mil.

3.1.1 Critical/Major Variances: The Contractor must submit all critical/major variance requests via DCMA or SUPSHIP and the PCO, to the SYCOM Program Office or their delegated representative, for approval or disapproval. All approved critical/major variances require a contract modification by the PCO prior to final inspection and acceptance of the items.

3.1.2 Minor Variances: For minor RFVs, delivery and/or shipment of such items under this contract is not permitted until the request is approved by the cognizant DCMA CMO, SUPSHIP, or SYSCOM TWH. On Navy Special Emphasis Program contracts/purchase orders, the Contractor must submit minor variance requests via DCMA or SUPSHIP and the PCO, to the SYSCOM Program Office or their delegated representative, for approval or disapproval.

3.2 The Contractor is not entitled to any equitable adjustment to the contract price or terms based on the Government's disapproval of a major/critical or minor variance.

(12-23)

PART I - THE SCHEDULE

SECTION D

PACKAGING AND MARKING

ACTIVITY USE ONLY: TDP VERSION NO.: 001NIIN: 016903471

ITEM NAME: DETECTOR SUPPORT AS

5. PACKAGING

5.1 Preservation, Packaging, Packing and Marking - Preservation, Packaging, Packing and Marking shall be in accordance with the Contract/Purchase Order Schedule and as specified below.

MIL-STD 2073 PACKAGING APPLIES AS FOUND ELSEWHERE IN THE SCHEDULE

ACTIVITY USE ONLY: TDP VERSION NO.: 001NIIN: 016904087

ITEM NAME: PSMC ASSEMBLY

5. PACKAGING

5.1 Preservation, Packaging, Packing and Marking - Preservation, Packaging, Packing and Marking shall be in accordance with the Contract/Purchase Order Schedule and as specified below.

MIL-STD 2073 PACKAGING APPLIES AS FOUND ELSEWHERE IN THE SCHEDULE

NIIN: 016905244

ACTIVITY USE ONLY: TDP VERSION NO.: 001

SPRMM1-26-R-RA08 PAGE 11 OF 64

ITEM NAME: ASSEMBLY, DISPLAY M

5. PACKAGING

5.1 Preservation, Packaging, Packing and Marking - Preservation, Packaging, Packing and Marking shall be in accordance with the Contract/Purchase Order Schedule and as specified below.

MIL-STD 2073 PACKAGING APPLIES AS FOUND ELSEWHERE IN THE SCHEDULE

ACTIVITY USE ONLY: TDP VERSION NO.: 001NIIN: 016905713

ITEM NAME: ASSEMBLY, SWITCH MO

5. PACKAGING

5.1 Preservation, Packaging, Packing and Marking - Preservation, Packaging, Packing and Marking shall be in accordance with the Contract/Purchase Order Schedule and as specified below.

MIL-STD 2073 PACKAGING APPLIES AS FOUND ELSEWHERE IN THE SCHEDULE

252.211-7003

ITEM UNIQUE IDENTIFICATION AND VALUATION (JAN 2023)

(a) Definitions. As used in this clause-

"Automatic identification device" means a device, such as a reader or interrogator, used to retrieve data encoded on machine-readable media.

"Concatenated unique item identifier" means-

(1) For items that are serialized within the enterprise identifier, the linking together of the unique identifier data elements in order of the issuing agency code, enterprise identifier, and unique serial number within the enterprise identifier; or

(2) For items that are serialized within the original part, lot, or batch number, the linking together of the unique identifier data elements in order of the issuing agency code; enterprise identifier; original part, lot, or batch number; and serial number within the original part, lot, or batch number.

"Data matrix" means a two-dimensional matrix symbology, which is made up of square or, in some cases, round modules arranged within a perimeter finder pattern and uses the Error Checking and Correction 200 (ECC200) specification found within International Standards Organization (ISO)/International Electrotechnical Commission (IEC) 16022.

"Data qualifier' means a specified character (or string of characters) that immediately precedes a data field that defines the general category or intended use of the data that follows.

"DoD recognized unique identification equivalent" means a unique identification method that is in commercial use and has been recognized by DoD. All DoD recognized unique identification equivalents are listed at https://www.acq.osd.mil/asda/dpc/ce/ds/unique-id.html

"DoD item unique identification" means a system of marking items delivered to DoD with unique item identifiers that have machine-readable data elements to distinguish an item from all other like and unlike items. For items that are serialized within the enterprise identifier, the unique item identifier shall include the data elements of the enterprise identifier and a unique serial number. For items that are serialized within the part, lot, or batch number within the enterprise identifier, the unique item identifier shall include the data elements of the enterprise identifier; the original part, lot or batch number; and the serial number.

"Enterprise" means the entity (e.g., a manufacturer or vendor) responsible for assigning unique item identifiers to items.

"Enterprise identifier" means a code that is uniquely assigned to an enterprise by an issuing agency.

"Government's unit acquisition cost" means-

(1) For fixed-price type line, subline, or exhibit line items, the unit price identified in the contract at the time of delivery;

(2) For cost-type or undefinitized line, subline, or exhibit line items, the Contractor's estimated fully burdened unit cost to the Government at the time of delivery; and

(3) For items produced under a time-and-materials contract, the Contractor's estimated fully burdened unit

TECHNICAL DATA PACKAGE

NIIN: 016905248 VERSION: 001 PAGE 1

ITEM NAME: ASSEMBLY, CONTROL E OCTOBER 14, 2025

1. SCOPE

1.1 This contract/purchase order contains the requirements for manufacture and the contract quality requirements for the ASSEMBLY, CONTROL E .

2. APPLICABLE DOCUMENTS

2.1 Applicable Documents - The document(s) listed below form a part of this contract/purchase order including modifications or exclusions.

2.1.1 "Document References" listed below must be obtained by the Contractor. Ordering information is included as an attachment to this contract/purchase order.

3. REQUIREMENTS

3.1 Cage Code/Reference Number Items - The ASSEMBLY, CONTROL E furnished under this contract/purchase order shall be the design represented by Cage Code(s) reference number(s). Cage _______ ref. no.

<53711 8602246>

3.2 Marking - This item shall be physically identified in accordance with <MIL-STD-130, REV N, 16 NOV 2012> .

3.3 Changes in Design, Material Servicing, or Part Number - Except for a Code 1 change, which shall be processed as provided in the code statement shown below, no substitution of items shall be made until the NAVICP-MECH Contracting Officer has notified and approval has been given by issuance of a written change order. When any change in design, material, servicing or part number is made to replace or substitute any item to be furnished on this contract/purchase order, the Contractor shall furnish, for the substituting/replacement item, a drawing and an explanation of the reason for the change, explaining the reason therefor. If finished detail drawings are not available, shop drawings in the form used by the manufacturer will be acceptable for Government evaluation. When notifying the Procurement Contracting Officer of the reasons for making substitutions, the type of change shall be indicated by code number in accordance with one of the following statements:

Code 1: PART NUMBER CHANGE ONLY - If the Manufacturer's Part Number indicated thereon has changed, but the parts are identical in all respects, supply the item and advise NAVICP-MECH immediately of the new part number.

Code 2: Assembly (or set or kit) not furnished - Used following detail parts.

Code 3: Part not furnished separately - Use assembly.

Code 4: Part redesigned - Old and new parts are completely interchangeable.

Code 5: Part redesigned - New part replaces old. Old part cannot replace new.

Code 6: Part redesigned - Parts not interchangeable.

4. QUALITY ASSURANCE

4.1 Responsibility for Inspection - Unless otherwise specified in the contract/purchase order, the Contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract/purchase order, the Contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements.

4.2 Responsibility for Compliance - All items must meet all requirements of this contract/purchase order. The inspection set forth in this specification shall become a part of the Contractor's overall inspection system or quality program. The absence of any inspection requirements shall not relieve the Contractor of the responsibility of assuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract/purchase order. Sampling in quality conformance does not authorize submission of known defective material, either indicated or actual, not does it commit the Government to acceptance of defective material.

4.3 Records - Records of all inspection work by the Contractor shall be kept complete and available to the Government during the performance of contract/purchase order and for a period of 365 calendar days after final delivery of supplies.

5. PACKAGING

5.1 Preservation, Packaging, Packing and Marking - Preservation, Packaging, Packing and Marking shall be in accordance with the Contract/Purchase Order Schedule and as specified below.

MIL-STD 2073 PACKAGING APPLIES AS FOUND ELSEWHERE IN THE SCHEDULE

6. NOTES

NIIN: 016905248 VERSION: 001 PAGE 2

ITEM NAME: ASSEMBLY, CONTROL E OCTOBER 14, 2025

6.1 Ordering Information for Document References - The Department of Defense Single Stock Point (DODSSP), Website http://www.dsp.dla.mil/, provides product information for the Department Of Defense Index Of Specifications and Standards (DODISS) (i.e.Military/Federal Specifications and Standards), Data Item Descriptions (DIDs), and other DODSSP Products. Most Specifications can obtained directly from http://quicksearch.dla.mil/

A. Availability of Cancelled Documents - The DODSSP offers cancelled documentsthat are required by private industry in fulfillment of contractual obligationsin paper format. Documents can be requested by phoning the Subscription Services Desk.

B. Commercial Specifications, Standards, and Descriptions - These specifications, standards and descriptions are not available from Government sources. Theymay be obtained from the publishers of the applicable societies.

C. Ordnance Standards (OS), Weapons Specifications (WS), and NAVORD OSTD 600 Pages - These type publications may be obtained by submitting a request to:

Commander, Indian Head Division, Naval Surface Warfare Center Code 8410P, 101 Strauss Avenue Indian Head, MD 20640-5035

D. On post-award actions, requests for "Official Use Only" and "NOFORN" (Not Releasable To Foreign Nationals) documents must identify the Government ContractNumber, and must be submitted via the cognizant Defense Contract Management Command (DCMC) for certification of need for the document. On pre-award actions such requests must be submitted to the PCO for certification of need for the document.

E. NOFORN Military Specifications and Standards (including Amendments, Change Notices and Supplements, but NOT interim Changes) to be ordered from:

Contracting Officer

NAVSUP-WSS

Code 87321 5450 Carlisle Pike P.O. Box 2020 Mechanicsburg, Pa. 17055-0788

F. Nuclear Reactor Publications Assigned NAVSEA Documents and Identification Numbers (i.e. NAVSEA Welding Standard, NAVSEA 250-1500-1) are to be ordered enue:

Commanding Officer

NAVSUP-WSS

Code 009 5450 Carlisle Pike P.O. Box 2020 Mechanicsburg, Pa. 17055-0788

G. Technical Manuals Assigned NAVSEA Identification Numbers (i.e. NAVSEA Welding And Brazing Procedure, NAVSEA S9074-AQ-GIB-010/248) are to be ordered from:

Commanding Officer

NAVSUP-WSS

Code 1 Support Branch 700 Robbins Avenue Philadelphia, Pa. 19111-5094

H. Interim Changes and Classified Specifications must be obtained by submitting a request on DD Form 1425 to

NAVSUP-WSS.

6.2 Notice To Distributors/Offerors - Consideration for award of contract shall be given only to authorized distributors of the original manufacturer's item represented in this solicitation. If you desire to be considered as a potential source for award of this contract, proof of being an authorized distributor shall be provided on company letterhead signed by a responsible company official and sent with your offer to the Procurement Contracting Officer.

6.3 In accordance with OPNAVINST 5510.1 all documents and drawings provided by the U.S. Navy to perspective Contractors must include a "Distribution Statement" to inform the contractor of the limits of distribution, and the safeguarding of the information contained on those documents and drawings.

There are 7 (seven) seperate distribution statement codes used for non-classified documents and drawings. The definition for each is as follows:

A... approved for public release; distribution is unlimited.

B... distribution authorized to US Governments agencies only.

C... distribution authorized to US Government agencies and their contractors.

D... distribution authorized to DoD and DoD contractors only.

E... distribution authorized to DoD Components only.

F... further distribution only as directed by Commander, Naval Sea

Systems Command, code 09T.

X... distribution is authorized to US Government agencies and private individuals or enterprises eligible to

NIIN: 016905248 VERSION: 001 PAGE 3

ITEM NAME: ASSEMBLY, CONTROL E OCTOBER 14, 2025

obtain export controlled technical data in accordance with OPNAVINST 5510.161.

SPRMM1-26-R-RA08 PAGE 12 OF 64

252.211-7003 (CONT)

ITEM UNIQUE IDENTIFICATION AND VALUATION (JAN 2023)

cost to the Government at the time of delivery.

"Issuing agency" means an organization responsible for assigning a globally unique identifier to an enterprise, as indicated in the Register of Issuing Agency Codes for ISO/IEC 15459, located at http://www.aimglobal.org/?Reg_Authority15459.

"Issuing agency code" means a code that designates the registration (or controlling) authority for the enterprise identifier.

"Item" means a single hardware article or a single unit formed by a grouping of subassemblies, components, or constituent parts.

"Lot or batch number" means an identifying number assigned by the enterprise to a designated group of items, usually referred to as either a lot or a batch, all of which were manufactured under identical conditions.

"Machine-readable" means an automatic identification technology media, such as bar codes, contact memory buttons, radio frequency identification, or optical memory cards.

"Original part number" means a combination of numbers or letters assigned by the enterprise at item creation to a class of items with the same form, fit, function, and interface.

"Parent item" means the item assembly, intermediate component, or subassembly that has an embedded item with a unique item identifier or DoD recognized unique identification equivalent.

"Serial number within the enterprise identifier" means a combination of numbers, letters, or symbols assigned by the enterprise to an item that provides for the differentiation of that item from any other like and unlike item and is never used again within the enterprise.

"Serial number within the part, lot, or batch number" means a combination of numbers or letters assigned by the enterprise to an item that provides for the differentiation of that item from any other like item within a part, lot, or batch number assignment.

"Serialization within the enterprise identifier" means each item produced is assigned a serial number that is unique among all the tangible items produced by the enterprise and is never used again. The enterprise is responsible for ensuring unique serialization within the enterprise identifier.

"Serialization within the part, lot, or batch number" means each item of a particular part, lot, or batch number is assigned a unique serial number within that part, lot, or batch number assignment. The enterprise is responsible for ensuring unique serialization within the part, lot, or batch number within the enterprise identifier.

"Type designation" means a combination of letters and numerals assigned by the Government to a major end item, assembly or subassembly, as appropriate, to provide a convenient means of differentiating between items having the same basic name and to indicate modifications and changes thereto.

"Unique item identifier" means a set of data elements marked on items that is globally unique and unambiguous. The term includes a concatenated unique item identifier or a DoD recognized unique identification equivalent.

"Unique item identifier type" means a designator to indicate which method of uniquely identifying a part has been used. The current list of accepted unique item identifier types is maintained at https://www.acq.osd.mil/asda/dpc/ce/ds/unique-id.html

(b) The Contractor shall deliver all items under a contract line, subline, or exhibit line item.

(c) Unique item identifier.

(1) The Contractor shall provide a unique item identifier for the following:

(i) Delivered items for which the Government's unit acquisition cost is $5,000 or more; except for the

SPRMM1-26-R-RA08 PAGE 13 OF 64

ITEM UNIQUE IDENTIFICATION AND VALUATION (JAN 2023)

following line items:

Contract Line, Subline, or Exhibit Line Item Number Item Description

(ii) Items for which the Government's unit acquisition cost is less than $5,000 that are identified in the Schedule or the following table:

Contract Line, Subline, or Exhibit Line Item Number Item Description

(If items are identified in the Schedule, insert "See Schedule" in this table.)

(iii) Subassemblies, components, and parts embedded within delivered items, items with warranty requirements, DoD serially managed reparables and DoD serially managed nonreparables as specified in Attachment Number < > .

(iv) Any item of special tooling or special test equipment as defined in FAR 2.101 that have been designated for preservation and storage for a Major Defense Acquisition Program as specified in Attachment Number < >

(v) Any item not included in paragraphs (c)(1)(i), (ii), (iii), or (iv) of this clause for which the contractor creates and marks a unique item identifier for traceability.

(2) The unique item identifier assignment and its component data element combination shall not be duplicated on any other item marked or registered in the DoD Item Unique Identification Registry by the contractor.

(3) The unique item identifier component data elements shall be marked on an item using two dimensional data matrix symbology that complies with ISO/IEC International Standard 16022, Information technology - International symbology specification - Data matrix; ECC200 data matrix specification.

(4) Data syntax and semantics of unique item identifiers. The Contractor shall ensure that --

(i) The data elements (except issuing agency code) of the unique item identifier are encoded within the data matrix symbol that is marked on the item using one of the following three types of data qualifiers, as determined by the Contractor:

(A) Application Identifiers (AIs) (Format Indicator 05 of ISO/IEC International Standard 15434), in accordance with ISO/IEC International Standard 15418, Information Technology - EAN/UCC Application Identifiers and Fact Data Identifiers and Maintenance and ANSI MH 10.8.2 Data Identifier and Application Identifier Standard.

(B) Data Identifiers (DIs) (Format Indicator 06 of ISO/IEC International Standard 15434), in accordance with ISO/IEC International Standard 15418, Information Technology - EAN/UCC Application Identifiers and Fact Data Identifiers and Maintenance and ANSI MH 10.8.2 Data Identifier and Application Identifier…