2.01 RFP SPRMM126RRA08.pdf

CAUTION TO OFFERORS - NO CONTRACT WILL BE AWARDED UNDER

THIS SOLICITATION AT GREATER THAN FAIR AND REASONABLE PRICES.

SECTION A - COVER SHEET

(See Section L of the Table of Contents in

You are cautioned to note the "Certification of Non-Segregated Facilities" in the solicitation. Failure to agree to the certification will render your reply nonresponsive to the terms of solicitations involving awards of contracts exceeding $25,000 which are not exempt from the provisions of the Equal Opportunity clause.

"Fill-ins" are provided on the face and reverse of Standard Form 18 and Parts I and IV of Standard Form 33, or other solicitation documents and Sections of Table of Contents in this solicitation and should be examined for applicability.

See the provision of this solicitation entitled "Late Bids, Modifications of Bids or Withdrawal of Bids" or "Late Proposals, Modifications of Proposals and Withdrawals of Proposals."

When submitting your reply,the envelope used must be plainly marked with the Solicitation Number, as shown above and the date and local time set forth for bid opening or receipt of proposals in the solicitation document.

If NO RESPONSE is to be submitted, detach this sheet from the solicitation, complete the information requested on reverse,fold, affix postage, and mail. NO ENVELOPE IS NECESSARY.

Replies must set forth full, accurate, and complete information as required by this solicitation The penalty for making false statements is prescribed in 18 U.S.C.1001.

(X one).

a. SEALED BID

c. NEGOTIATED (RFQ)

INSTRUCTIONS

NOTE THE AFFIRMATIVE ACTION REQUIREMENT OF THE EQUAL OPPORTUNITY CLAUSE WHICH MAY APPLY TO THE CONTRACT

RESULTING FROM THIS SOLICITATION.

3. ISSUING OFFICE

(including attachments).

4. ITEMS TO BE PURCHASED

5 PROCUREMENT INFORMATION

a. THIS PROCUREMENT IS UNRESTRICTED

b. THIS PROCUREMENT IS A ______% SET-ASIDE FOR ONE OF THE FOLLOWING

1. SOLICITATION NUMBER

INFORMATION TO OFFERORS OR QUOTERS

6. ADDITIONAL INFORMATION

(1) Small Business (2) Labor Surplus Area Concerns (3) Combined Small Business/Labor Area Concerns

DD Form 1707, MAR 89 Previous editions are obsolete.

(Brief description)

(Complete mailing address, including Zip Code)

(X one) this solicitation for details of the set-aside.)

(X and complete as applicable)

461/089

2.

b. NEGOTIATED (RFP)

7. POINT OF CONTACT FOR INFORMATION

a. NAME (Last, First, Middle Initial) b. ADDRESS (Include Zip Code)

c. TELEPHONE NUMBER (Include Area Code and Extension) (NO COLLECT CALLS)

SPRMM1-26-R-RA08

X

25198-0080 (IDIQ T)

SPRMM1 DLA MECHANICSBURG

DLR PROCUREMENT OPS DSCC-ZI COC W5

P. O. BOX 2020, 5450 CARLISLE PIKE

MECHANICSBURG PA 17055-0788

SEE SCHEDULE

X

S. MCDONNELL ZIL1

SPRMM1 DLA MECHANICSBURG

( ) - MECHANICSBURG PA 17055-0788

KKKKKKKKKKKKKKKKKKKJ

KKKKKKKKKKKKKKKKKKKJ

e. OTHER

8. REASONS FOR NO RESPONSE

DD Form 1707 Reverse, MAR 89

(1) Typed or Printed Name

d. DO NOT REGULARLY MANUFACTURE OR SELL THE TYPE OF ITEMS INVOLVED

b. CANNOT MEET DELIVERY REQUIREMENT

c. UNABLE TO IDENTIFY THE ITEM(S)

a. CANNOT COMPLY WITH SPECIFICATIONS

9. MAILING LIST INFORMATION

WE DESIRE TO BE RETAINED ON THE MAILING LIST FOR FUTURE PROCUREMENT OF THE TYPE OF ITEM(S) INVOLVEDYES NO

10. RESPONDING FIRM

a. COMPANY NAME b. ADDRESS

c. ACTION OFFICER

(4) Date Signed

AFFIX

STAMP

HERE

(X all that apply)

FROM

DATE (YYMMDD)

SOLICITATION NUMBER

LOCAL TIME TO

(Last, First, Middle Initial) (YYMMDD)

(2) Title (3) Signature

FOLDFOLD

FOLD FOLD

(Specify)

(X one)

(INCLUDE ZIP CODE)

SPRMM1-26-R-RA08

03:00 P.M.227 FEB 2026

SOLICITATION, OFFER AND AWARD

2. CONTRACT NUMBER

PAGE OF PAGES

1 64

6. REQUISITION/PURCHASE NUMBER

7. ISSUED BY

CODE

8. ADDRESS OFFER TO (If other than item 7)

25198-0080

DLA WEAPONS SUPPORT - MECHANICSBURG

DLA PROCUREMENT OPS DLA - ZI

DLA MECHANICSBURG - CODE ZIL1

P.O. 2020, 5450 CARLISLE PIKE

MECHANICSBURG, PA 17055-0788

NOTE: In sealed bid solicitations "offer" and "offeror" mean "bid" and "bidder".

SOLICITATION

9. Sealed offers in original and copies for furnishings the supplies or services in the Schedule will be received at the place specified in item 8, or if hand carried, in the depository located in BLDG. 203, NORTH END, CODE ZIL1 until 5:00 PM local time 2/27/2026 (Hour) (Date)

CAUTION - LATE Submissions, Modifications, and Withdrawals: See Section L, Provision No. 52.214-7 or 52.215-1. All offers are subject to all terms and conditions contained in this solicitation.

10. FOR

INFORMATION

CALL:

A. NAME

SEAN MCDONNELL

B. TELEPHONE (NO COLLECT CALLS) C. E-MAIL ADDRESS

sean.mcdonnell@dla.mil

AREA CODE

NUMBER

EXTENSION

11. TABLE OF CONTENTS

(X) SEC. DESCRIPTION PAGE(S) (X) SEC. DESCRIPTION PAGE(S)

PART I - THE SCHEDULE PART II - CONTRACT CLAUSES

A SOLICITATION/CONTRACT FORM 1 I CONTRACT CLAUSES 25

B SUPPLIES OR SERVICES AND PRICES/COSTS 3 PART III - LIST OF DOCUMENTS, EXHIBITS AND OTHER ATTACH.

C DESCRIPTION/SPECS./WORK STATEMENT 4-5 J LIST OF ATTACHMENTS 42

D PACKAGING AND MARKING 10-19 PART IV - REPRESENTATIONS AND INSTRUCTIONS

E INSPECTION AND ACCEPTANCE 19

K REPRESENTATIONS, CERTIFICATIONS AND OTHER

STATEMENTS OF OFFERORS 43

F DELIVERIES OR PERFORMANCE 21

G CONTRACT ADMINISTRATION DATA 23-25 L INSTRUCTIONS, CONDITIONS, AND NOTICES TO OFFERORS 60

H SPECIAL CONTRACT REQUIREMENTS 25 M EVALUATION FACTORS FOR AWARD 62

OFFER (Must be fully completed by offeror) NOTE: Item 12 does not apply if the solicitation includes the provisions at 52.214-16, Minimum Bid Acceptance Period.

12. In compliance with the above, the undersigned agrees, if this offer is accepted within calendar days (60 calendar days unless a different period is inserted by the offeror) from the date for receipt of offers specified above, to furnish any or all items upon which prices are offered at the set opposite each item, delivered at the designated point(s), within the time specified in the schedule.

13. DISCOUNT FOR PROMPT PAYMENT

(See Section I, Clause No. 52.232-8)

10 CALENDAR DAYS (%) 20 CALENDAR DAYS (%) 30 CALENDAR DAYS (%) CALENDAR DAYS(%)

14. ACKNOWLEDGMENT OF AMENDMENTS

(The offeror acknowledges receipt of amendments to the SOLICITATION for offerors and related documents numbered and dated):

AMENDMENT NO. DATE AMENDMENT NO. DATE

15A. NAME AND

ADDRESS

OF OFFEROR

CODE FACILITY 16. NAME AND THE TITLE OF PERSON AUTHORIZED TO SIGN

OFFER(Type or print)

15B. TELEPHONE NUMBER 15C. CHECK IF REMITTANCE ADDRESS IS

DIFFERENT FROM ABOVE - ENTER SUCH

ADDRESS IN SCHEDULE.

17. SIGNATURE 18. OFFER DATE

AREA CODE NUMBER EXTENSION

AWARD (To be completed by Government)

19. ACCEPTED AS TO ITEMS NUMBERED 20. AMOUNT 21. ACCOUNTING AND APPROPRIATION

22. AUTHORITY FOR USING OTHER THAN FULL OPEN COMPETITION:

10 U.S.C. 2304 (c) 41 U.S.C. 3304(a) ( )

23. SUBMIT INVOICES TO ADDRESS SHOWN IN ITEM

(4 copies unless otherwise specified)

24. ADMINISTERED BY (If other than Item 7) 25. PAYMENT WILL BE MADE BY CODE

26. NAME OF CONTRACTING OFFICER (Type or print) 27. UNITED STATES OF AMERICA

(Signature of Contracting Officer)

28. AWARD DATE

IMPORTANT - Award will be made on this Form, or on Standard Form 26, or by other authorized official written notice.

AUTHORIZED FOR LOCAL REPRODUCTION

Previous edition is unusable

STANDARD FORM 33 (REV. 6/2014)

Prescribed by GSA - FAR (48 CFR) 53.214 (c)

SPRMM1

5. DATE ISSUED

1/26/2026

4. TYPE OF SOLICITATION

SEALED BID (IFB)

NEGOTIATED (RFP)

3. SOLICITATION NUMBER

SPRMM126RRA08

RATING

DO-A3

1. THIS CONTRACT IS A RATED ORDER

UNDER DPAS (15 CFR 700)

mailto:sean.mcdonnell@dla.mil

SPRMM126RRA08

(PLEASE NOTE THAT SECTIONS B THROUGH H MAY NOT BE IN ALPHABETICAL ORDER. PLEASE READ SOLICITATION

IN ITS ENTIRETY).

SECTION A

GENERAL INFORMATION FOR OFFERORS

1. The purpose of this solicitation is to establish an indefinite-delivery type contract for the supplies listed in Section B, that will provide stock coverage for customers both overseas and in the United States, including Alaska and Hawaii, and our possessions.

2. Under this solicitation, the resulting contract will be a Firm-Fixed-Price, Indefinite-Quantity Contract issued under FAR Part 15, with a 3-year base period and 2 one-year option periods. The total contract period will be five years. The terms “year” or “contract year,” as used in this solicitation, mean a period of 365 days beginning on the contract start date and every 365 days thereafter, except for a leap year, in which the contract year shall be 366 days.

3. The method used to place orders under this contract will be: Delivery Orders placed by DLA Weapons Support at Mechanicsburg (DLA-Mech). DLA-Mech will issue delivery orders with the awardee for the supplies cited in Section B. This contract is not obligating any funds. Funding will be provided on each delivery order placed under the contract.

4. The proposals received in response to this solicitation will be evaluated under Lowest Price Technically Acceptable “LPTA” procedures as described in Section M of this solicitation.

5. Please note that contractors shall complete all contractor required fill-ins and submit the pricing spreadsheet along with all pages of the solicitation to sean.mcdonnell@dla.mil, regardless of the number of CLINs that are proposed on. These sections are pertinent to understanding the requirements of the solicitation.

6. Some clauses/provisions may not appear in the correct section (D-M) due to system constraints.

7. NOTE TO POTENTIAL OFFERORS: Due to repetitive demands, the Government may place multiple awards.

Offers should be aware that the only guarantee upon award is for the contract minimum split equally among awardees.

8. Pursuant to FAR 16.504 (c)(1)(ii)(C), a single award will be made for the planned ID-IQs because: Only one contractor is capable of providing performance at the level of quality required because the supplies and services are unique or highly specialized. Spectral Labs Inc. is the Sole Source, Original Equipment Manufacturer (OEM) of the items and multiple awards would not be in the best interest of the Government.

CONTRACT MINIMUM VALUE – Qty 1 each CONTRACT MAXIMUM VALUE - $6,975,450.00 (calculated as 7.5 x ADV for each NSN) mailto:sean.mcdonnell@dla.mil

SECTION B – SCHEDULE OF SUPPLIES

1. This solicitation is for the acquisition of parts specified under Section B Spreadsheet information/ instructions below. Offerors shall provide their pricing in the Section B Pricing Spreadsheet found below.

2. Section B Spreadsheet Information/Instructions.

FSC NIIN Part Number Item Unit of Measure

6350 016903471 8602252 DETETCTOR SUPPORT EA

6120 016904087 8602255 PSMC ASSEMBLY EA

5980 016905244 8602261 DISPLAY ASSEMBLY EA

5998 016905248 8602246 CONTROL ASSEMBLY EA

5930 016905713 8602245 SWITCH ASSEMBLY EA

Place of Inspection Supplies & Packaging: Offeror fills in the CAGE code of the place of inspection for supplies and packaging. If locations are the same as offeror’s address, offeror can indicate “SAME”.

3. Section B – Pricing Spreadsheet

CLIN NSN ADQ Qty Ranges From

Qty Ranges To

Base Year 1

Base Year 2

Base Year 3

Option Year 1

Option Year 2

0001 6350 016903471 15 1 10

11 20

21 30

0002 6120 016904087 15 1 10

11 20

21 30

0003 5980 016905244 15 1 10

11 20

21 30

0004 5998 016905248 15 1 10

11 20

21 30

0005 5930 016905713 15 1 10

11 20

21 30

***NOTE: Basic drawing or specification indicating the item is manufactured by Government drawing or specification. The offeror upon completing pricing for this item, certifies that the item is manufactured IAW all drawing/specifications stated within the solicitation. This column gives only the basic drawing/specification number. See basic specification for basic secondary drawing information.

CLIN(s)/NSN: Self-Explanatory

ADQ: ADQ = Estimated Annual Demand Quantity

Quantity Ranges: Self-Explanatory

Year One – Year Five: Offeror should fill in the base year and each option year unit price for each quantity range.

For all CLINs the unit prices shall be priced as FOB Origin. Unit prices proposed should include all costs associated with providing the item in accordance with all terms and conditions stated in the solicitation and resultant contract.

SECTION D – PACKAGING AND MARKING

Packaging shall be in accordance with MIL-STD-2073 unless otherwise specified in the delivery order, as certain immediate use requirements may allow for commercial packaging in accordance with ASTM-D-3951 - Standard Practice for Commercial items.

The MIL-STD-2073 packaging shall be in conformance with the following Packaging Requirement Code (PRC) on page 2 of this solicitation.

NSN: 6350 016903471 PCK CTGY CD: ZZZ0

HM QUP ICQ PMT CD PM WM CUD CT UC LP IC UCL SP MK PACK UNIT PKWT

N 001 000 41 1 00 EA GE D ED A 00 B 00 EFF 9.5

UNIT PKCU OPI CAGE SPI NUMBER REV SPI DATE CONTAINER NSN

.145 O

NSN: 6120 016904087 PCK CTGY CD: ZZZ0

HM QUP ICQ PMT CD PM WM CUD CT UC LP IC UCL SP MK PACK UNIT PKWT

N 001 000 41 1 00 EA GE D ED A 00 B 00 EFF 3.5

UNIT PKCU OPI CAGE SPI NUMBER REV SPI DATE CONTAINER NSN

.290 O

NSN: 5980 016905244 PCK CTGY CD: ZZZ0

HM QUP ICQ PMT CD PM WM CUD CT UC LP IC UCL SP MK PACK UNIT PKWT

N 001 000 41 1 00 EA GE D ED A 00 B 00 EFF 3.1

UNIT PKCU OPI CAGE SPI NUMBER REV SPI DATE CONTAINER NSN

.257 O

NSN: 5998 016905248 PCK CTGY CD: ZZZ0

HM QUP ICQ PMT CD PM WM CUD CT UC LP IC UCL SP MK PACK UNIT PKWT

N 001 000 41 1 00 EA GE D ED A 00 B 00 EFF 2.2

UNIT PKCU OPI CAGE SPI NUMBER REV SPI DATE CONTAINER NSN

.223 O

NSN: 5930 016905713 PCK CTGY CD: ZZZ0

HM QUP ICQ PMT CD PM WM CUD CT UC LP IC UCL SP MK PACK UNIT PKWT

N 001 000 41 1 00 EA GE D ED A 00 B 00 EFF 3.1

UNIT PKCU OPI CAGE SPI NUMBER REV SPI DATE CONTAINER NSN

.233 O

SECTION E – INSPECTION & ACCEPTANCE

Please identify the following, if different from your facility/cage. If locations are the same as offeror’s address, offeror can indicate “SAME”.

CAGE for performance: ________________ CAGE for inspection: ________________ CAGE for acceptance: ________________

SECTION F – DELIVERIES OR PERFORMANCE

PLACE OF DELIVERY: The place of delivery for all items to be acquired hereunder will be specified in individual delivery orders issued under this Indefinite Delivery – Indefinite Quantity contract.

TIME OF DELIVERY:

Offeror's Proposed Delivery Time: ____ days

ACCELERATED DELIVERIES: Accelerated deliveries in advance of the specified delivery schedule are authorized. Any accelerated delivery will be at no additional expense to the Government, unless specifically authorized by the Procuring or Administrative Contracting Officer.

PARTIAL SHIPMENTS: Shipments of item quantities less than each line item quantity specified in the delivery order schedule are authorized. Multiple shipments to one destination are authorized. Any partial shipment will be at no additional expense to the Government, unless specifically authorized by the Procuring or Administrative Contracting Officer.

*NOTE - See Section I, FAR clause 52.216-18, Ordering

All contractual documents (i.e. contracts, purchase orders, task orders, delivery orders and modifications) related to the instant procurement are considered to be issued by the Government when copies are either deposited in the mail, transmitted by facsimile, or sent by other electronic commerce methods, such as email. The Government's acceptance of the contractor's proposal constitutes bilateral agreement to issue contractual documents as detailed herein.

SPRMM1-26-R-RA08 PAGE 6 OF 64

PART I - THE SCHEDULE

SECTION B

SUPPLIES OR SERVICES AND PRICES/COSTS

WSSTERMBZ04

IMPORTANT NOTICE REGARDING HAZARDOUS MATERIAL

FAR clause 52.223-3, Hazardous Material Identification and Material Safety Data, is incorporated by reference in Section I in this solicitation ad required offerors to--

(1) identify any hazardous material (defined in FED STD 313 as an item or chemical which is a "health or physical hazard" per OSHA in 29 CFR 1910.1200) that will be delivered under a resultant contract, and

(2) provide a Material Safety Data Sheet meeting OSHA/FED STD 313 requirements for all hazardous material identified.

While not an all-inclusive listing of hazardous material, at a minimum, any it em with a four-digit Federal Supply Code (FSC), which correlates to the first four positions of the National Stock Number (NSN), of 6810, 6820, 6830, 6840, 6850, 7930, 8010, 8030, 8040, 9110, 9135, 9140, 9150, or 9160 is considered hazardous material and requires submission of a Material Safety Data Sheet or an appropriate representation that there is no hazardous material contained in the item.

Failure to provide the required information and documentation may render you ineligible for award. If you have questions about whether a solicited item is classified as hazardous, contact the NAVSUP WSS HAZMAT point of contact, NAVSUP WSS Code 0772, at (717)605-1361. (10-06)

PART I - THE SCHEDULE

SECTION C

DESCRIPTION/SPECIFICATIONS/WORK STATEMENT

CLIN: 0001

NIIN: 016903471 ACTIVITY USE ONLY: TDP VERSION NO.: 001

ITEM NAME: DETECTOR SUPPORT AS

1. SCOPE

1.1 This contract/purchase order contains the requirements for manufacture and the contract quality requirements for the DETECTOR SUPPORT AS .

2. APPLICABLE DOCUMENTS

2.1 Applicable Documents - The document(s) listed below form a part of this contract/purchase order including modifications or exclusions.

2.1.1 "Document References" listed below must be obtained by the Contractor. Ordering information is included as an attachment to this contract/purchase order.

3. REQUIREMENTS

3.1 Cage Code/Reference Number Items - The DETECTOR SUPPORT AS furnished under this contract/purchase order shall be the design represented by Cage Code(s) reference number(s). Cage _______ ref. no.

<549W5 8602252>

3.2 Marking - This item shall be physically identified in accordance with <MIL-STD-130, REV N, 16 NOV 2012> .

3.3 Changes in Design, Material Servicing, or Part Number - Except for a Code 1 change, which shall be processed as provided in the code statement shown below, no substitution of items shall be made until the NAVICP-MECH Contracting Officer has notified and approval has been given by issuance of a written change order. When any change in design, material, servicing or part number is made to replace or substitute any item to be furnished on this contract/purchase order, the Contractor shall furnish, for the substituting/replacement item, a drawing and an explanation of the reason for the change, explaining the reason therefor. If finished detail drawings are not available, shop drawings in the form used by the manufacturer will be acceptable for Government evaluation. When notifying the Procurement Contracting Officer of the reasons for making substitutions, the type of change shall be indicated by code number in accordance with one of the following statements:

SPRMM1-26-R-RA08 PAGE 7 OF 64

Code 1: PART NUMBER CHANGE ONLY - If the Manufacturer's Part Number indicated thereon has changed, but the parts are identical in all respects, supply the item and advise NAVICP-MECH immediately of the new part number.

Code 2: Assembly (or set or kit) not furnished - Used following detail parts.

Code 3: Part not furnished separately - Use assembly.

Code 4: Part redesigned - Old and new parts are completely interchangeable.

Code 5: Part redesigned - New part replaces old. Old part cannot replace new.

Code 6: Part redesigned - Parts not interchangeable.

CLIN: 0002

NIIN: 016904087 ACTIVITY USE ONLY: TDP VERSION NO.: 001

ITEM NAME: PSMC ASSEMBLY

1. SCOPE

1.1 This contract/purchase order contains the requirements for manufacture and the contract quality requirements for the PSMC ASSEMBLY .

2. APPLICABLE DOCUMENTS

2.1 Applicable Documents - The document(s) listed below form a part of this contract/purchase order including modifications or exclusions.

2.1.1 "Document References" listed below must be obtained by the Contractor. Ordering information is included as an attachment to this contract/purchase order.

3. REQUIREMENTS

3.1 Cage Code/Reference Number Items - The PSMC ASSEMBLY furnished under this contract/purchase order shall be the design represented by Cage Code(s) reference number(s). Cage _______ ref. no.

<53711 8602255>

3.2 Marking - This item shall be physically identified in accordance with <MIL-STD-130, REV N, 16 NOV 2012> .

3.3 Changes in Design, Material Servicing, or Part Number - Except for a Code 1 change, which shall be processed as provided in the code statement shown below, no substitution of items shall be made until the NAVICP-MECH Contracting Officer has notified and approval has been given by issuance of a written change order. When any change in design, material, servicing or part number is made to replace or substitute any item to be furnished on this contract/purchase order, the Contractor shall furnish, for the substituting/replacement item, a drawing and an explanation of the reason for the change, explaining the reason therefor. If finished detail drawings are not available, shop drawings in the form used by the manufacturer will be acceptable for Government evaluation. When notifying the Procurement Contracting Officer of the reasons for making substitutions, the type of change shall be indicated by code number in accordance with one of the following statements:

Code 1: PART NUMBER CHANGE ONLY - If the Manufacturer's Part Number indicated thereon has changed, but the parts are identical in all respects, supply the item and advise NAVICP-MECH immediately of the new part number.

Code 2: Assembly (or set or kit) not furnished - Used following detail parts.

Code 3: Part not furnished separately - Use assembly.

Code 4: Part redesigned - Old and new parts are completely interchangeable.

Code 5: Part redesigned - New part replaces old. Old part cannot replace new.

Code 6: Part redesigned - Parts not interchangeable.

CLIN: 0003

NIIN: 016905244 ACTIVITY USE ONLY: TDP VERSION NO.: 001

ITEM NAME: ASSEMBLY, DISPLAY M

1. SCOPE

SPRMM1-26-R-RA08 PAGE 8 OF 64

1.1 This contract/purchase order contains the requirements for manufacture and the contract quality requirements for the ASSEMBLY, DISPLAY M .

2. APPLICABLE DOCUMENTS

2.1 Applicable Documents - The document(s) listed below form a part of this contract/purchase order including modifications or exclusions.

2.1.1 "Document References" listed below must be obtained by the Contractor. Ordering information is included as an attachment to this contract/purchase order.

3. REQUIREMENTS

3.1 Cage Code/Reference Number Items - The ASSEMBLY, DISPLAY M furnished under this contract/purchase order shall be the design represented by Cage Code(s) reference number(s). Cage _______ ref. no.

<549W5 8602261>

3.2 Marking - This item shall be physically identified in accordance with <MIL-STD-130, REV N, 16 NOV 2012> .

3.3 Changes in Design, Material Servicing, or Part Number - Except for a Code 1 change, which shall be processed as provided in the code statement shown below, no substitution of items shall be made until the NAVICP-MECH Contracting Officer has notified and approval has been given by issuance of a written change order. When any change in design, material, servicing or part number is made to replace or substitute any item to be furnished on this contract/purchase order, the Contractor shall furnish, for the substituting/replacement item, a drawing and an explanation of the reason for the change, explaining the reason therefor. If finished detail drawings are not available, shop drawings in the form used by the manufacturer will be acceptable for Government evaluation. When notifying the Procurement Contracting Officer of the reasons for making substitutions, the type of change shall be indicated by code number in accordance with one of the following statements:

Code 1: PART NUMBER CHANGE ONLY - If the Manufacturer's Part Number indicated thereon has changed, but the parts are identical in all respects, supply the item and advise NAVICP-MECH immediately of the new part number.

Code 2: Assembly (or set or kit) not furnished - Used following detail parts.

Code 3: Part not furnished separately - Use assembly.

Code 4: Part redesigned - Old and new parts are completely interchangeable.

Code 5: Part redesigned - New part replaces old. Old part cannot replace new.

Code 6: Part redesigned - Parts not interchangeable.

CLIN: 0004

NIIN: 016905713 ACTIVITY USE ONLY: TDP VERSION NO.: 001

ITEM NAME: ASSEMBLY, SWITCH MO

1. SCOPE

1.1 This contract/purchase order contains the requirements for manufacture and the contract quality requirements for the ASSEMBLY, SWITCH MO .

2. APPLICABLE DOCUMENTS

2.1 Applicable Documents - The document(s) listed below form a part of this contract/purchase order including modifications or exclusions.

2.1.1 "Document References" listed below must be obtained by the Contractor. Ordering information is included as an attachment to this contract/purchase order.

3. REQUIREMENTS

3.1 Cage Code/Reference Number Items - The ASSEMBLY, SWITCH MO furnished under this contract/purchase order shall be the design represented by Cage Code(s) reference number(s). Cage _______ ref. no.

<549W5 8602245>

3.2 Marking - This item shall be physically identified in accordance

SPRMM1-26-R-RA08 PAGE 9 OF 64

with <MIL-STD-130, REV N, 16 NOV 2012> .

3.3 Changes in Design, Material Servicing, or Part Number - Except for a Code 1 change, which shall be processed as provided in the code statement shown below, no substitution of items shall be made until the NAVICP-MECH Contracting Officer has notified and approval has been given by issuance of a written change order. When any change in design, material, servicing or part number is made to replace or substitute any item to be furnished on this contract/purchase order, the Contractor shall furnish, for the substituting/replacement item, a drawing and an explanation of the reason for the change, explaining the reason therefor. If finished detail drawings are not available, shop drawings in the form used by the manufacturer will be acceptable for Government evaluation. When notifying the Procurement Contracting Officer of the reasons for making substitutions, the type of change shall be indicated by code number in accordance with one of the following statements:

Code 1: PART NUMBER CHANGE ONLY - If the Manufacturer's Part Number indicated thereon has changed, but the parts are identical in all respects, supply the item and advise NAVICP-MECH immediately of the new part number.

Code 2: Assembly (or set or kit) not furnished - Used following detail parts.

Code 3: Part not furnished separately - Use assembly.

Code 4: Part redesigned - Old and new parts are completely interchangeable.

Code 5: Part redesigned - New part replaces old. Old part cannot replace new.

Code 6: Part redesigned - Parts not interchangeable.

WSSTERMCZ05

CONFIGURATION MANAGEMENT - MARITIME

1.0 Configuration Management

1.1 The cognizant systems command (SYSCOM), Naval Sea Systems Command (NAVSEA) or Naval Information Warfare Systems Command (NAVWAR), Program Manager will maintain configuration control and change authority for all items in this contract.

1.2 In accordance with the configuration management provisions of this contract, the Contractor must maintain the total Equipment baseline configuration of the parts on this contract including, but not limited to, hardware, software and firmware.

NOTE: The latest revisions of the DOD Forms referenced in this term can be found at https://www.esd.whs.mil/dd. The latest revisions of the DIDs referenced in this term can be found at https://quicksearch.dla.mil/.

2.0 Engineering Changes

2.1 The Government will not be responsible for any contract delay or disruption or any increased costs of performance of the Contractor due to a misclassification of an Engineering Change Proposal (ECP) by the Contractor, including those costs associated with replacement of delivered items resulting from such a misclassification. ECP's are classified as either Class I (Major) or Class II (Minor). For detailed classification criteria refer to DD Form 1692 instructions sheet. ECPs must be prepared in accordance with DI-SESS-80639E, Engineering Change Proposal (ECP).

NOTE: Any ECP or notification of an ECP submitted to the PCO in accordance with this paragraph must also be copied to the NAVSUP WSS CM Team at usn.philadelphia.navsupwssphil.mbx.configuration-management@us.navy.mil.

2.1.1 Class I (Major) Changes: The Contractor must coordinate with the cognizant SYSCOM Program Office prior to any Class I ECP submission. The Contractor must notify the Procurement Contracting Officer (PCO) of any pending or approved Class I engineering changes with another Government activity that the Contractor proposes to incorporate under this contract. The cognizant SYSCOM Program Office will approve or disapprove of Class I changes. Any approved Class I change may necessitate contract changes by the PCO, which changes may be handled under the Changes clause of this contract, FAR 52.243-1 The Contractor must not implement a Class I change on this contract until a contract modification is issued by the PCO.

2.1.2 Class II (Minor) Changes: Class II changes must be submitted to the cognizant Defense Contract Management Agency (DCMA) Contract Management Office (CMO), or to the Supervisor of Shipbuilding (SUPSHIP) Groton, for concurrence in classification and may be implemented only upon receiving DCMA, SUPSHIP, or NAVSEA/NAVWAR Technical Warrant Holder (TWH) concurrence. On Navy Special Emphasis Program contracts/purchase orders, the Contractor must submit the Class II (Minor) change to the PCO for approval or disapproval. Class II changes must be made at no additional cost to the Government.

SPRMM1-26-R-RA08 PAGE 10 OF 64

WSSTERMCZ05 (CONT)

CONFIGURATION MANAGEMENT - MARITIME

2.2 The Contractor is not entitled to any equitable adjustment to the contract price or terms based on the Government's disapproval of a Class I or Class II ECP.

3.0 Variances

3.1 The Contractor must not deliver any item for acceptance by the Government that incorporates a known departure from product definition information unless a Request for Variance (RFV) has been approved. Authorized variances are a temporary departure from the requirements only and do not authorize a change to the item's configuration baseline.

RFVs are classified as Critical, Major, or Minor. For detailed classification criteria refer to the DD Form 1694 instructions sheet. Variance requests must be prepared in accordance with DI-SESS-80640E - Request for Variance

(RFV).

NOTE: Any RFV submitted to the PCO in accordance with this paragraph must also be copied to the NAVSUP WSS RFV Review Team at usn.philadelphia.navsupwssphil.mbx.rfv-review-team@us.navy.mil.

3.1.1 Critical/Major Variances: The Contractor must submit all critical/major variance requests via DCMA or SUPSHIP and the PCO, to the SYCOM Program Office or their delegated representative, for approval or disapproval. All approved critical/major variances require a contract modification by the PCO prior to final inspection and acceptance of the items.

3.1.2 Minor Variances: For minor RFVs, delivery and/or shipment of such items under this contract is not permitted until the request is approved by the cognizant DCMA CMO, SUPSHIP, or SYSCOM TWH. On Navy Special Emphasis Program contracts/purchase orders, the Contractor must submit minor variance requests via DCMA or SUPSHIP and the PCO, to the SYSCOM Program Office or their delegated representative, for approval or disapproval.

3.2 The Contractor is not entitled to any equitable adjustment to the contract price or terms based on the Government's disapproval of a major/critical or minor variance.

(12-23)

PART I - THE SCHEDULE

SECTION D

PACKAGING AND MARKING

ACTIVITY USE ONLY: TDP VERSION NO.: 001NIIN: 016903471

ITEM NAME: DETECTOR SUPPORT AS

5. PACKAGING

5.1 Preservation, Packaging, Packing and Marking - Preservation, Packaging, Packing and Marking shall be in accordance with the Contract/Purchase Order Schedule and as specified below.

MIL-STD 2073 PACKAGING APPLIES AS FOUND ELSEWHERE IN THE SCHEDULE

ACTIVITY USE ONLY: TDP VERSION NO.: 001NIIN: 016904087

ITEM NAME: PSMC ASSEMBLY

5. PACKAGING

5.1 Preservation, Packaging, Packing and Marking - Preservation, Packaging, Packing and Marking shall be in accordance with the Contract/Purchase Order Schedule and as specified below.

MIL-STD 2073 PACKAGING APPLIES AS FOUND ELSEWHERE IN THE SCHEDULE

NIIN: 016905244

ACTIVITY USE ONLY: TDP VERSION NO.: 001

SPRMM1-26-R-RA08 PAGE 11 OF 64

ITEM NAME: ASSEMBLY, DISPLAY M

5. PACKAGING

5.1 Preservation, Packaging, Packing and Marking - Preservation, Packaging, Packing and Marking shall be in accordance with the Contract/Purchase Order Schedule and as specified below.

MIL-STD 2073 PACKAGING APPLIES AS FOUND ELSEWHERE IN THE SCHEDULE

ACTIVITY USE ONLY: TDP VERSION NO.: 001NIIN: 016905713

ITEM NAME: ASSEMBLY, SWITCH MO

5. PACKAGING

5.1 Preservation, Packaging, Packing and Marking - Preservation, Packaging, Packing and Marking shall be in accordance with the Contract/Purchase Order Schedule and as specified below.

MIL-STD 2073 PACKAGING APPLIES AS FOUND ELSEWHERE IN THE SCHEDULE

252.211-7003

ITEM UNIQUE IDENTIFICATION AND VALUATION (JAN 2023)

(a) Definitions. As used in this clause-

"Automatic identification device" means a device, such as a reader or interrogator, used to retrieve data encoded on machine-readable media.

"Concatenated unique item identifier" means-

(1) For items that are serialized within the enterprise identifier, the linking together of the unique identifier data elements in order of the issuing agency code, enterprise identifier, and unique serial number within the enterprise identifier; or

(2) For items that are serialized within the original part, lot, or batch number, the linking together of the unique identifier data elements in order of the issuing agency code; enterprise identifier; original part, lot, or batch number; and serial number within the original part, lot, or batch number.

"Data matrix" means a two-dimensional matrix symbology, which is made up of square or, in some cases, round modules arranged within a perimeter finder pattern and uses the Error Checking and Correction 200 (ECC200) specification found within International Standards Organization (ISO)/International Electrotechnical Commission (IEC) 16022.

"Data qualifier' means a specified character (or string of characters) that immediately precedes a data field that defines the general category or intended use of the data that follows.

"DoD recognized unique identification equivalent" means a unique identification method that is in commercial use and has been recognized by DoD. All DoD recognized unique identification equivalents are listed at https://www.acq.osd.mil/asda/dpc/ce/ds/unique-id.html

"DoD item unique identification" means a system of marking items delivered to DoD with unique item identifiers that have machine-readable data elements to distinguish an item from all other like and unlike items. For items that are serialized within the enterprise identifier, the unique item identifier shall include the data elements of the enterprise identifier and a unique serial number. For items that are serialized within the part, lot, or batch number within the enterprise identifier, the unique item identifier shall include the data elements of the enterprise identifier; the original part, lot or batch number; and the serial number.

"Enterprise" means the entity (e.g., a manufacturer or vendor) responsible for assigning unique item identifiers to items.

"Enterprise identifier" means a code that is uniquely assigned to an enterprise by an issuing agency.

"Government's unit acquisition cost" means-

(1) For fixed-price type line, subline, or exhibit line items, the unit price identified in the contract at the time of delivery;

(2) For cost-type or undefinitized line, subline, or exhibit line items, the Contractor's estimated fully burdened unit cost to the Government at the time of delivery; and

(3) For items produced under a time-and-materials contract, the Contractor's estimated fully burdened unit

SPRMM1-26-R-RA08 PAGE 12 OF 64

252.211-7003 (CONT)

ITEM UNIQUE IDENTIFICATION AND VALUATION (JAN 2023)

cost to the Government at the time of delivery.

"Issuing agency" means an organization responsible for assigning a globally unique identifier to an enterprise, as indicated in the Register of Issuing Agency Codes for ISO/IEC 15459, located at http://www.aimglobal.org/?Reg_Authority15459.

"Issuing agency code" means a code that designates the registration (or controlling) authority for the enterprise identifier.

"Item" means a single hardware article or a single unit formed by a grouping of subassemblies, components, or constituent parts.

"Lot or batch number" means an identifying number assigned by the enterprise to a designated group of items, usually referred to as either a lot or a batch, all of which were manufactured under identical conditions.

"Machine-readable" means an automatic identification technology media, such as bar codes, contact memory buttons, radio frequency identification, or optical memory cards.

"Original part number" means a combination of numbers or letters assigned by the enterprise at item creation to a class of items with the same form, fit, function, and interface.

"Parent item" means the item assembly, intermediate component, or subassembly that has an embedded item with a unique item identifier or DoD recognized unique identification equivalent.

"Serial number within the enterprise identifier" means a combination of numbers, letters, or symbols assigned by the enterprise to an item that provides for the differentiation of that item from any other like and unlike item and is never used again within the enterprise.

"Serial number within the part, lot, or batch number" means a combination of numbers or letters assigned by the enterprise to an item that provides for the differentiation of that item from any other like item within a part, lot, or batch number assignment.

"Serialization within the enterprise identifier" means each item produced is assigned a serial number that is unique among all the tangible items produced by the enterprise and is never used again. The enterprise is responsible for ensuring unique serialization within the enterprise identifier.

"Serialization within the part, lot, or batch number" means each item of a particular part, lot, or batch number is assigned a unique serial number within that part, lot, or batch number assignment. The enterprise is responsible for ensuring unique serialization within the part, lot, or batch number within the enterprise identifier.

"Type designation" means a combination of letters and numerals assigned by the Government to a major end item, assembly or subassembly, as appropriate, to provide a convenient means of differentiating between items having the same basic name and to indicate modifications and changes thereto.

"Unique item identifier" means a set of data elements marked on items that is globally unique and unambiguous. The term includes a concatenated unique item identifier or a DoD recognized unique identification equivalent.

"Unique item identifier type" means a designator to indicate which method of uniquely identifying a part has been used. The current list of accepted unique item identifier types is maintained at https://www.acq.osd.mil/asda/dpc/ce/ds/unique-id.html

(b) The Contractor shall deliver all items under a contract line, subline, or exhibit line item.

(c) Unique item identifier.

(1) The Contractor shall provide a unique item identifier for the following:

(i) Delivered items for which the Government's unit acquisition cost is $5,000 or more; except for the

SPRMM1-26-R-RA08 PAGE 13 OF 64

ITEM UNIQUE IDENTIFICATION AND VALUATION (JAN 2023)

following line items:

Contract Line, Subline, or Exhibit Line Item Number Item Description

(ii) Items for which the Government's unit acquisition cost is less than $5,000 that are identified in the Schedule or the following table:

Contract Line, Subline, or Exhibit Line Item Number Item Description

(If items are identified in the Schedule, insert "See Schedule" in this table.)

(iii) Subassemblies, components, and parts embedded within delivered items, items with warranty requirements, DoD serially managed reparables and DoD serially managed nonreparables as specified in Attachment Number < > .

(iv) Any item of special tooling or special test equipment as defined in FAR 2.101 that have been designated for preservation and storage for a Major Defense Acquisition Program as specified in Attachment Number < >

(v) Any item not included in paragraphs (c)(1)(i), (ii), (iii), or (iv) of this clause for which the contractor creates and marks a unique item identifier for traceability.

(2) The unique item identifier assignment and its component data element combination shall not be duplicated on any other item marked or registered in the DoD Item Unique Identification Registry by the contractor.

(3) The unique item identifier component data elements shall be marked on an item using two dimensional data matrix symbology that complies with ISO/IEC International Standard 16022, Information technology - International symbology specification - Data matrix; ECC200 data matrix specification.

(4) Data syntax and semantics of unique item identifiers. The Contractor shall ensure that --

(i) The data elements (except issuing agency code) of the unique item identifier are encoded within the data matrix symbol that is marked on the item using one of the following three types of data qualifiers, as determined by the Contractor:

(A) Application Identifiers (AIs) (Format Indicator 05 of ISO/IEC International Standard 15434), in accordance with ISO/IEC International Standard 15418, Information Technology - EAN/UCC Application Identifiers and Fact Data Identifiers and Maintenance and ANSI MH 10.8.2 Data Identifier and Application Identifier Standard.

(B) Data Identifiers (DIs) (Format Indicator 06 of ISO/IEC International Standard 15434), in accordance with ISO/IEC International Standard 15418, Information Technology - EAN/UCC Application Identifiers and Fact Data Identifiers and Maintenance and ANSI MH 10.8.2 Data Identifier and Application Identifier Standard.

(C) Text Element Identifiers (TEIs)(Format Indicator 12 of ISO/IEC International Standard 15434), in accordance with the Air Transport Association Common Support Data Dictionary; and

(ii) The encoded data elements of the unique item identifier conform to the transfer structure, syntax, and coding of messages and data formats specified for Format Indicators 05, 06, and 12 in ISO/IEC International Standard 15434, Information Technology - Transfer Syntax for High Capacity Automatic Data Capture Media.

(5) Unique item identifier.

(i) The Contractor shall-

(A) Determine whether to-

(1) Serialize within the enterprise identifier;

(2) Serialize within the part, lot, or batch number; or

(3) Use a DoD recognized unique identification equivalent; (e.g. Vehicle Identification Number):

and

(B) Place the data elements of the unique item identifier (enterprise identifier; serial number: DoD recognized unique identification equivalent; and for serialization within the part, lot, or batch number only:

original part, lot or batch number) on items requiring marking by paragraph (c)(1) of this clause, based on the criteria provided in MIL-STD-130, Identification Marking of U.S. Military Property, latest version:

(C) Label shipments, storage containers and packages that contain uniquely identified items in accordance with the requirements of MIL-STD-129, Military Marking for Shipment and Storage, latest version; and

(D) Verify that the marks on items and labels on shipments, storage containers, and packages are machine readable and conform to the applicable standards. The contractor shall use an automatic identification technology device for this verification that has been programmed to the requirements of Appendix A, MIL-STD-130, SPRMM1-26-R-RA08 PAGE 14 OF 64

ITEM UNIQUE IDENTIFICATION AND VALUATION (JAN 2023)

latest version.

(ii) The issuing agency code-

(A) Shall not be placed on the item; and

(B) Shall be derived from the data qualifier for the enterprise identifier.

(d) For each item that requires item unique identification under paragraph (c)(1)(i), (ii) or (iv) of this clause or when item unique identification is provided under paragraph (c)(1)(v), in addition to the information provided as part of the Material Inspection and Receiving Report specified elsewhere in this contract, the Contractor shall report at the time of delivery, as part of the Material Inspection and Receiving Report, the following information:

(1) Unique item identifier.

(2) Unique item identifier type.

(3) Issuing agency code (if concatenated unique item identifier is used).

(4) Enterprise identifier (if concatenated unique item identifier is used).

(5) Original part number (if there is serialization within the original part number)

(6) Lot or batch number (if there is serialization within the lot or batch number).

(7) Current part number (optional and only if not the same as the original part number).

(8) Current part number effective date (optional and only if current part number is used).

(9) Serial number (if concatenated unique item identifier is used).

(10) Government's unit acquisition cost.

(11) Unit of measure.

(12) Type designation of the item as specified in the contract schedule, if any.

(13) Whether the item is an item of Special Tooling or Special Test Equipment.

(14) Whether the item is covered by a warranty.

(e) For embedded subassemblies, components, and parts that require DoD item unique identification under paragraph (c)(1)(iii) of this clause or when item unique identification is provided under paragraph (c)(1)(v), the Contractor shall report as part of the Material Inspection and Receiving Report specified elsewhere in this contract, the following information:

(1) Unique item identifier of the parent item under paragraph (c)(1) of this clause that contains the embedded subassembly, component, or part.

(2) Unique item identifier of the embedded subassembly, component, or part.

(3) Unique item identifier type.**

(4) Issuing agency code (if concatenated unique item identifier is used).**

(5) Enterprise identifier (if concatenated unique item identifier is used)**

(6) Original part number (if there is serialization within the original part number).**

(7) Lot or batch number (if there is serialization within the lot or batch number).**

(8) Current part number (optional and only if not the same as the original part number).**

(9) Current part number effective date (optional and only if current part number is used).**

(10) Serial number (if concatenated unique item identifier is used.)**

(11) Description.

** Once per item.

(f) The Contractor shall submit the information required by paragraphs (d) and (e) of this clause as follows:

(1) End items shall be reported using the receiving report capability in Wide Area WorkFlow (WAWF) in accordance with the clause at 252.232-7003. If WAWF is not required by this contract, and the contractor is not using WAWF, follow the procedures at http://dodprocurementtoolbox.com/site/uidregistry/.

(2) Embedded items shall be reported by one of the following methods-

(i) Use of the embedded items capability in WAWF;

(ii) Direct data submission to the IUID Registry following the procedures and formats at http:/dodprocurementtoolbox.com/site/uidregistry/; or

(iii) Via WAWF as a deliverable attachment for exhibit line item number < > , Unique Item Identifier

Report for Embedded Items, Contract Data Requirements List, DD Form 1423.

(g) Subcontracts. If the Contractor acquires by subcontract any item(s) for which item unique identification is required in accordance with paragraph (c)(1) of this clause, the Contractor shall include this clause, including this paragraph (g), in the applicable subcontract(s), including subcontracts for commercial products or commercial services.

WSSTERMDZ03

PRESERVATION, PACKAGING, PACKING AND MARKING

The contractor shall preserve, package, pack and mark all items as cited below. Where specifications or standards are cited herein the latest revision of that specification or standard shall apply.

1. PRESERVATION REQUIREMENTS

a. SYSTEM STOCK SHIPMENTS - The contractor shall preserve all items intended to enter the military distribution

SPRMM1-26-R-RA08 PAGE 15 OF 64

WSSTERMDZ03 (CONT)

PRESERVATION, PACKAGING, PACKING AND MARKING

system for stock in accordance with the MIL-STD-2073-1, "Standard Practice for Military Packaging", Packaging Requirements Code specified in the Section B, Part I of the Schedule. When a Specialized Preservation Code/Method of Preservation (MOP) (Table J-Ia) is specified, and one or more of the following packaging fields (WM, CUD, CT, UC) value is a 00 (numeric), the Specialized Preservation/MOP procedure and materials takes precedence. Contractors should disregard the LP field and third digit of the PACK field and use the Unit Container Level (UCL) to identify the level of packing protection the unit container meets for packing requirements. When HM = D, the item is regulated in accordance with Title 49 Code of Federal Regulations (CFR); when HM = N the item is not regulated for transportation.

1) When a specified packaging material has an associated Qualified Products List (QPL), the contractor shall use only packaging materials produced by a manufacturer listed on the applicable QPL. Barrier materials that have QPLs are MIL-PRF-131, MIL-PRF-81705, MIL-PRF-22191, MIL-PRF-3420 and MIL-PRF-22019. Sources for QPL material can be obtained from the Qualified Products Database at http://qpldocs.dla.mil/.

b. IMMEDIATE USE/INSTALLATION AND PART NUMBER BUY SHIPMENTS - Government PCO or ACO approval is required to use the packaging standards outlined in this paragraph. Any national stock numbered (NSN) item required for immediate use (used or consumed within 7 days of receipt) or direct installation, or part numbered item (authority granted to ship without NSN) shall be preserved and packed in accordance with ASTM D3951-18 (2023), "Standard Practice for Commercial Packaging", for all shipments to a Continental United States (CONUS) government activity or contractor-owned facility. All material destined for overseas shipment (OCONUS) shall be preserved in accordance with MIL-STD-2073-1.

c. GOVERNMENT-OWNED MATERIAL - In the event that the contract expires, is terminated, or completed, and Government-owned material is to be returned to the supply system, the contractor shall preserve…