SPECIFICATIONS FOR A CUSTOM BUILT - WEBSTER FIRE~1.pdf

Webster Fire Department 55 Thompson Rd

Webster, Massachusetts 01570

SPECIFICATIONS FOR A CUSTOM BUILT

FIRE FIGHTING & RESCUE VESSEL

TECHNICAL SPECIFICATIONS

1. SCOPE OF THE CONTRACT

The work performed under this contract shall consist of the complete construction, outfitting, testing, and delivery of a 22’ Landing Craft Fireboat or equal brand of aluminum vessel.

Construction of this vessel shall be in accordance with this specification and to the highest standards of marine construction. The vessel shall conform to all regulatory standards in effect at the time of construction.

Does your RFP comply with this requirement? YES ( ) NO ( )

A qualified representative shall familiarize the purchaser in the operation, care, and maintenance of the vessel and vendor supplied equipment. The final inspection trip shall be dedicated to the familiarization of all boat systems and equipment as well as sea trails.

Does your RFP comply with this requirement? YES ( ) NO ( )

The vendor shall provide all labor, engineering, equipment, materials, supplies, tools, transportation, storage, design, administration, financing, and quality control for the construction of the vessel and successful completion of the project.

Does your RFP comply with this requirement? YES ( ) NO ( )

2. GENERAL DESCRIPTION

Vendor will provide a marine aluminum boat ready with Firefighting and Search & Rescue capabilities with the following specifications.

• All 5083 marine grade aluminum construction, hull

• ¼ bottom, 3/16 sides, 3/1 five-bar non-skid self-bailing deck

• Reinforced hull framing and bow grounding package - INCLUDED

• Vee bottom hull with outside reverse chines and directional strakes

• Bow Push Knees, port and starboard

• Square bow with 60” electric/power drop gate and side stowage lockers at bow. Power gate has dual controls, at bow and at helm

• Two (2) foredeck flush-mounted cargo lugs to secure ATV/Four-Wheeler, or other

• One removable manual lifting davit, can be used port or starboard near bow

• Safety rail on top of dive door, to act as lower step when in the water

• Fold-down divers’ side door with integral ladder

• Two (2) waterline divers’ grab bars, port and starboard sides

• Center Console with Plexiglas windscreen, safety grab bars

• 200W Solar Panel on roof top

• Pre-wired Battery Charger

• Two marine batteries

• In-dash VHF Marine Radio

• One 60-gallon below-deck fuel tank

• Six (6) mooring cleats

• Port and starboard gunnel height storage lockers

• HD Stern Tow Post/Bollard

• Heavy-duty dual bar motor guard with Stokes basket location

• Aluminum hard top roof with Two (2) White and Red Overhead Dome lights

• Dive flag holder on roof, fold-down or removable

• Rub rails with integrated grab rails

• One (1) Go Light roof-mounted search light or equivalent

• Navigation lights, six gang breaker panel, horn, bilge pump and high-water alarm

• One (1) Power Point Plug-USB Combo receptacle

• Six (6) LED Diffused Lights on Roof for scene lighting

• Four (4) Red LED under-gunnel deck lights

• Two (2) LED Docking Lights

Propulsion Drive System

• One (1) New, current model Single O/B YAMAHA 200 HP Motor

• Digital/Electronic Controls

• Water Fuel Separators, S/S Prop, Tie Bar and PDI

Trailer

• Tandem-axle aluminum bunk trailer, tongue jack, 2” coupler, rubber-mounted lighting, safety chains with snap hooks, spare tire.

Emergency Lighting

• Whelen IT9P Mini Liberty II Perm MT (color TBD)

• Whelen SA315P Speaker

• Whelen WPA3BM Water Proof Control Head, Bail Mount

• Whelen 112 Waterproof Siren Amp

3. DIMENSIONS and PRINCIPAL CHARACTERISTICS

Length Overall 22'

Beam Overall 8’- 8’6”

Height Overall 10’- 10’6” trailer ride height

Weight (Light) 4,500 pounds

Fuel Capacity 60 gallons

Top Speed 30-40 knots

4. WARRANTIES and SERVICE

Hull and deck: minimum 10 years on materials and workmanship.

Does your RFP comply with this requirement? YES ( ) NO ( )

Engine, full manufacturer’s warranty.

Does your RFP comply with this requirement? YES ( ) NO ( )

Equipment: manufacturer’s warranty.

Does your RFP comply with this requirement? YES ( ) NO ( )

Vendor shall maintain factory authorized services and complete all warranty repairs in a timely manner. All warranty work shall be done on site whenever possible. In the event warranty work cannot be completed on site and the vessel needs to be transported back to the manufacturer’s plant or other designated repair facility(s), it shall be the responsibility of the manufacturer to transport the vessel and incur the cost of same.

5. TRIALS:

The vessel must successfully complete, to the satisfaction of the Buyer, the trials listed below at the builder’s facility:

Maneuverability in various conditions.

Does your RFP comply with this requirement? YES ( ) NO ( )

Acceleration and deceleration maximum thrust.

Does your RFP comply with this requirement? YES ( ) NO ( )

Testing of all equipment on fireboat. The successful Vendor shall make repairs, corrections, or re-designs, as appropriate, at no additional cost, if the boat fails the tests during sea trials.

Does your RFP comply with this requirement? YES ( ) NO ( )

These trials shall be at the manufacturers’ or vendors’ expense. Testing of all equipment in

6. MANUALS

Vendor shall provide two copies of the vessels service/parts manuals as supplied to the builder by the equipment’s manufacturer. The manuals will contain a recommend spare parts listing and a drawings package. Systems covered shall be navigation, main propulsion, pumps, electrical, lubrication, firefighting systems, communication, and vessel-operating procedures. The drawings package will contain as built drawings of the craft, including GA, Fore & Aft Sections, Piping

Arrangement, including fuel piping, Machinery and a detailed electrical schematic.