ATTACH_Tech_Data_03996.pdf

SLACKS, WOMEN'S (FLAT FRONT), WASH & WEAR

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL

AND QUALITY REQUIREMENTS FOUND ON THE WEB AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx. FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON

REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

shall be made in accordance with CG/PD 14-01, dated 10 March 2014.

Pattern Date: 18 March 2014.

CLOTH, TROPICAL: 75/25 Percent Polyester/Wool(Washable) CG Blue 3362, CG/PD 10-299, dated March 8, 2012.

STANDARD SAMPLE FOR THE CG BLUE 3362 IS IDENTIFIED

AS PIECE NUMBER 402122970 AND IS APPLICABLE

FOR SHADE and APPEARANCE ONLY.

INTERIM SPECIFICATION CHANGES CG/PD 14-01,dated 10 March 2014.

Page 6, after paragraph "3.5.2" insert the following paragraph:

"3.5.3 Each pair of slacks shall have the DLA Exclusive Woven Label. The jacquard woven Exclusive label shall specify "Made exclusively for Defense Logistics Agency" and shall include "by" and the contractor's name. The label shall be sewn to the bottom of the waistband opposite the size label, two inches off center back. The proposed finished label's design shall be submitted to the contracting officer for approval."

Page 6, Paragraph 3.7 Patterns, delete in its entirety and substitute, "Paragraph 3.7.

The Government will furnish a complete set of graded patterns. The pattern provides 1/2 inch for side seams, 1/2 inch for inseams tapered at knee notch to 7/8 inch at crotch for back leg outlet, 3/8 inch seam allowance starting at the crotch and gradually increasing to 1-1/4 inch at seat outlet seam for seat outlet seam, 3/8 inch seam allowance for front crotch, waistband attachment, and fly assemblies, and 1/4 inch for pocket facing and pocket assembly. The working patterns shall be identical to the Government patterns but may be modified to accommodate automation; however, if the working patterns are modified, the design and measurements must be maintained as intended by this document and the Government patterns."

Page 9, paragraph 3.8.11. Belt loops, line 1, delete "6" and substitute "0", line two, delete "4" and substitute "0", and line 3, delete "22" and substitute "28".

THE CONTRACTOR SHALL STAMP LEGIBLY WITH INDELIBLE INK THE LOT NUMBER ON EACH END ITEM

AND OUTER CONTAINER IN THE LOT.

LIST OF DOCUMENTS, EXHIBITS, AND OTHER ATTACHMENTS

a. This solicitation/award consists of the following documents, exhibits, and other attachments

b. DLA Troop Support Clothing & Textiles Additional Quality Assurance Requirements dated October 2018, which has superseded

DSCPM 4155.3, QUALITY SYSTEMS REQUIREMENTS, dated NOVEMBER 3, 1997.

c. DLA Troop Support Clothing and Textiles Additional Quality Assurance Requirements dated October 2018 additional changes:

Page 10 of 38, par. 2.1, line 4, after "(DCMA QAS)" add ", or Supplier's Source Sampling Representative, as applicable"

Page 11 of 38, par. 2.3, line 2, delete "to the source QAS".

Line 4, delete "source QAS" and replace with "Supplier's Source Sampling Representative". Page 12, par 2.3 (continued), delete "source QAS" and replace with "Supplier's Source Sampling Representative".

Page 12 of 38, par. 2.4, line 5, delete "as required" and replace with "if required".

Page 12 of 38, par. 3.1.1, after "entirely" add the following:

"For routine shade or physical testing of fabric lots, Government sampling is not required. The DD Form 1222 for routine shade or physical testing of fabric lots shall be signed and dated by the Supplier's Source Sampling Representative in Box 15."

Page 13 of 38, par. 3.1.2 - line 10, after "Government QAS" add the following: "or Supplier's Source Sampling Representative, as applicable,"

Page 14 of 38, par. 3.2.1 -line 4, delete "source QAS" and replace with "Supplier's Source Sampling Representative".

Page 14 of 38, par. 3.2.1.1 - cutting swatches, delete "DCMA QAS" and replace with "Supplier's Source Sampling Representative". After "single color rolls - 4"x 24"" delete "QAS" and replace with "Supplier's Source Sampling Representative". After "multi-color camouflage"... delete "QAS" and replace with "Supplier's Source Sampling Representative".

Page 14 of 38, par. 3.2.1.2 - line 3, delete "stamped,". Line 4, Delete "source QAS" and replace with "Supplier's Source Sampling Representative"

Page 15 of 38, par. 3.2.1.4 - subpar. 2, delete "source QAS" and replace with "Supplier's Source Sampling Representative"

Page 15 of 38, par. 3.2.2 - Line 3, delete "stamped,", delete "source QAS" and replace with "Supplier's Source Sampling

Representative". Line 4, delete "QAS" and replace with "Supplier's Source Sampling Representative".

Page 16 of 38, par. 3.3.1 - Line 2, after "(30)" add, "calendar". Line 3 and Line 6, after "QAS" add, "or Supplier's Source Sampling Representative"

Page 16 of 38, par. 3.3.2 - Delete the paragraph in its entirety, including subparagraphs labeled "a" through "i", and replace with the following:

"3.3.2. Contractor Furnished Material (CFM). DLA Troop Support Clothing and Textiles contracts require source sampling of CFM at finishing plants. The following provisions apply to sample selection and lot acceptance.

(a) The samples shall be randomly selected by the Supplier's Source Sampling Representative.

(b) Upon presentation of a lot, the Supplier's Source Sampling Representative will draw samples and forward the samples to the contractor's laboratory specified in the contract for testing.

(c) Shipment of Component Lots from the source to the prime contractor need not be deferred except for Government Acceptance Testing (i.e., shade evaluation). Commencement of production prior to receipt of a passing test report from the contractor's authorized laboratory is solely at the contractor's risk.

(d) The contractor will provide copies of Certificates of Compliance to the QAS.

(e) The contractor is required to ensure that a complete test report for all lots is furnished to the source's QAS and the appropriate DLA-PTC representative."

Pages 24, 25, 36 add to block 16: "By signing in box 15, I certify that the samples referenced above were randomly selected and represent the lot identified above.

**Special note: Contractors shall ensure that blocks 2 and 15 of the form DD1222 are updated to reflect the correct information.

Historically, both blocks contained the information of the DCMA QAR and their stamp/signature. When contractor's representative samples, these blocks shall include the contractor's representative's information. Block 17 shall still include the DCMA QAR to receive the results of the report even though they may not be sampling the material to be tested.

[End of interim changes.]

INCLUDE T0043 OBJECT TEXT ID ST

GOVERNMENT LABORATORY TESTING OF COMPONENTS FOR ACCEPTANCE

PURPOSE.

52.246-9030 SHADE EVALUATION OF CONTRACTOR FURNISHED MATERIALS:

SHADE SAMPLING IS APPLICABLE

The color of the test specimen shall match the standard sample viewed using AATCC Evaluation Procedure 9, Option A, with sources simulating artificial daylight D75 illuminant with a color temperature of 7500 (+/- 200)K, with illumination of 100 (+/- 20) foot candles, and shall be a good match to the standard sample under incandescent lamplight at 2856 (+/- 200)K.

FOR SHADE TESTING: THE COMPLETED DD FORM 1222 AND THE SWATCHES

SHALL BE FORWARDED TO:

DLA Product Testing Center Analytical 700 Robbins Avenue Philadelphia, PA 19111

ATTN: BLDG 5D

EMAIL: Uraina.Gray-Scully@dla.mil

PHONE: 215-737-3265

52.209-4, 52.209-9P01, WHEN 52.210-9P06 IS NOT INCLUDED, INSERT

THE FOLLOWING: "IF THE EXAMINATION INDICATES ONE OF THE

FOLLOWING: WHICHEVER IS APPLICABLE:

(1) NO DIMENSIONAL DEFECT IS FOUND AND NO MORE THAN 10% OF THE

UNITS EXAMINED ARE FOUND TO CONTAIN MAJOR OR MINOR "A" DEFECTS,

OR

(2) NO DIMENSIONAL DEFECT OR SELECTED DEFECT IS FOUND NOR MORE

THAN 10% OF UNITS EXAMINED ARE FOUND TO CONTAIN 3 OR 2 POINT

DEFECTS, OR

(3) WHEN THE CLASSIFICATION OF DEFECTS CONTAINS ONLY MAJOR OR

MINOR DEFECTS OR ONE CLASS OF DEFECTS ONLY, NO DIMENSIONAL

DEFECT IS FOUND NOR MORE THAN 10% OF THE UNITS EXAMINED ARE

FOUND TO CONTAIN A DEFECT.

INCLUDE T0029 OBJECT TEXT ID ST

THE FIRST ARTICLE SHALL BE 50 UNITS EXAMINED AT THE CONTRACTOR'S

PLANT FOR VISUAL AND DIMENSIONAL CONFORMANCE IN ACCORDANCE WITH

THOSE PARAS. CONTAINED IN SECTION 4 OF THE END ITEM

SPECIFICATION ENTITLED "END ITEM VISUAL EXAMINATION" (OR "VISUAL

EXAMINATION", AS APPLICABLE) AND "END ITEM DIMENSIONAL

EXAMINATION" (OR "DIMENSIONAL EXAMINATION" OR "EXAMINATION OF

FINISHED MEASUREMENTS", AS APPLICABLE) WITH THE EXCEPTION THAT

ALL 50 UNITS WILL BE VISUALLY EXAMINED AND THE SAMPLE SIZE FOR

DIMENSIONAL EXAMINATION SHALL BE 8: OR, WHEN SECTION 4 OF THE

END ITEM SPECIFICATION CITES A MILITARY STANDARD PROVISION FOR

EVALUATING QUALITY, THE VISUAL AND DIMENSIONAL EXAMINATION SHALL

BE MADE IN ACCORDANCE WITH THOSE PARAS. OF THE MIL-STD ENTITLED

"END ITEM EXAMINATION" AND "DIMENSIONAL EXAMINATION" WITH THE

EXCEPTIONS NOTED ABOVE.

ADD THIS PARA TO 52.209-4

SIGNIFICANT NOTE - "PALLETIZATION IS REQUIRED FOR THESE

SUPPLIES".

NOTE: THE FOLLOWING APPLIES TO ALL NON-MANUFACTURED WOOD

PACKAGING MATERIALS:

"All Wood Packaging Material (WPM) acquired by DOD must meet requirements of International Standards for Phytosanitary Measures (ISPM) 15, "Guidelines for Regulating Wood Packaging Materials in International Trade." DOD shipments inside and outside of the United States must meet ISPM 15 whenever WPM is used to ship DOD cargo, or when wood is being acquired by DLA for future use as packaging material. WPM is defined as wood pallets, skids, load boards, pallet collars, wooden boxes, reels, dunnage, crates, frame and cleats. Packaging materials exempt from the requirements are materials that have undergone a manufacturing process, such as corrugated fiberboard, plywood, particleboard, veneer, and oriented strand board (OSD). All WPM shall comply with one of the following official quality control programs:

Heat Treatment (HT) or Kiln Dried Heat Treatment (KD HT) in accordance with American Lumber Standard Committee, Incorporated (ALSC) Wood Packaging Material Program and WPM Enforcement Regulations (see http://www.alsc.org/; or

All WPM shall include certification/quality markings in accordance with the ALSC or NWPCA standards, as applicable.

Markings shall be placed in an unobstructed area that will be readily visible to inspectors. Pallet markings shall be applied to the stringer or block on diagonally opposite sides of the pallet and be contrasting and clearly visible.

All containers shall be marked on a side other than the top or bottom, contrasting and clearly visible. All dunnage used in configuring and/or securing the load shall also comply with ISPM 15 and be marked with an ASLC approved DUNNAGE stamp. Failure to comply with the requirements of this restriction may result in refusal, destruction, or treatment of materials at the point of entry. The Agency reserves the right to recoup from the Contractor any remediation costs incurred by the Government."

PALLET SHALL BE 4 WAY ENTRY, WINGED TYPE. PALLETIZED LOAD

DIMENSIONS SHALL NOT EXCEED 43 INCHES IN LENGTH, 52 INCHES IN

WIDTH, AND 54 INCHES IN HEIGHT (INCLUDING THE PALLET).

THE PALLETIZED LOAD SHALL BE BONDED USING APPROVED COMMERCIAL

BONDING MATERIALS. THE USE OF METAL BANDING, IN SECURING BOXES

TO PALLETS, IS DISCOURAGED. PALLET LOADS SHALL CONTAIN THE SAME

NUMBER OF CARTONS, OF IDENTICAL QUANTITIES, OF ONE NSN, TO THE

MAXIMUM EXTENT POSSIBLE.

PALLET LOADS CONTAINING MORE THAN ONE NSN SHALL BE CLEARLY

MARKED TO LIST ALL THE NSN'S CONTAINED IN THE LOAD. NO CARTON

SHALL HAVE MORE THAN ONE NSN. AT THE END OF A SIZE RUN, NO MORE

THAN ONE CARTON PER NSN MAY BE SHORT OR OVER THE SPECIFIED

QUANTITY. SAID CARTON SHALL BE CLEARLY MARKED "SHORT" OR

"OVER".

MIL-STD-147 IS REFERENCED FOR PALLETIZED LOADS.

IN ADDITION TO REQUIREMENTS SPECIFIED ABOVE THE FOLLOWING CLAUSE

ALSO APPLIES:

52.247-9012 - REQUIREMENTS FOR TREATEMENT OF WOOD PACKAGING

MATERIALS (WPM) - (JULY 2006)

INSPECTION AT SOURCE/ACCEPTANCE AT SOURCE

INCLUDE T1721 OBJECT TEXT ID ST

ADDITIONAL INFORMATION FOR ASL:

THE ACCEPTABLE SUPPLIER LISTING (ASL) AND QUALIFIED LABORATORY

LISTING (QLL) ARE NO LONGER VALID DOCUMENTS AND WILL NOT BE

PUBLISHED IN THE FUTURE. THE POINT OF CONTACT FOR QUESTIONS

PERTAINING TO LABORATORIES AND SUPPLIERS IS THE PROCUREMENT

BUYER, INDICATED IN THE SOLICITATION OR CONTRACT. QUESTIONS

SHOULD BE PROVIDED IN WRITING TO THE DESIGNATED BUYER.

CLAUSE 52.246-9032 IDENTIFICATION OF QUALIFIED LABORATORY AND

SOURCE SAMPLING APPLIES.

SHADE EVALUATION OF CONTRACTOR FURNISHED The color of the test specimen shall match the standard sample viewed using AATCC Evaluation Procedure 9, Option A, with sources simulating artificial daylight D75 illuminant with a color temperature of 7500 (+/-200) °K , with illumination of 100 (+/- 20) foot candles, and shall be a good match to the standard sample under incandescent lamplight at 2856 (+/- 200) °K.

MANDATORY USE OF STATISTICAL PROCESS CONTROLS

I. GENERAL REQUIREMENTS:

A. THE OFFEROR AGREES TO MANAGE AND IMPROVE PROCESS PERFORMANCE

THROUGH THE EVALUATION OF THE QUALITY OF THE PRODUCT AT THE

PRIME CONTRACTOR AND/OR SUBCONTRACTOR FACILITIES, USING

STATISTICAL PROCESS CONTROL (SPC) TECHNIQUES.

B. MINIMUM CRITERIA ARE ESTABLISHED IN THE AMERICAN SOCIETY OF

QUALITY CONTROL (ASQC) STANDARDS B.1, B.2 AND B.3 (FORMERLY THE

ANSI STANDARDS Z1.A, Z1.2 AND Z1.3). ALTERNATE SPC TECHNIQUES,

SUCH AS SHORT RUN METHODS ARE ALSO ALLOWED WHERE APPLICABLE.

C. THIS QUALITY ASSURANCE PROVISION (QAP) APPLIES TO ALL WORK

PERFORMED AT THE PRIME AND/OR SUBCONTRACTOR FACILITIES.

D. EXCLUSION OF SPC PLAN SUBMISSION: OFFERORS WHO CONSIDER

THEMSELVES ELIGIBLE FOR EXCLUSION OF THE SPC PLAN SUBMISSION

BASED ON SATISFACTORY UTILIZATION OF A PREVIOUSLY APPROVED SPC

PLAN FOR THE IDENTICAL OR SIMILAR SUPPLIES ARE TO SUBMIT A

WRITTEN REQUEST FOR EXCLUSION (RFE) TO THE PROCURING ACTIVITY.

INCLUDE 93390 OBJECT TEXT ID ST

REVIEW OF THIS ITEM HAS DETERMINED THAT THE SPECIFICATIONS,

STANDARDS, PRODUCT DESCRIPTIONS OR OTHER TECHNICAL DATA

APPLICABLE TO THIS PROCUREMENT ACTION DO NOT REQUIRE THE USE

OF CLASS I OZONE DEPLETING SUBSTANCES (ODS) OR ODC(S).

INCLUDE T0044 OBJECT TEXT ID ST

52.246-15 CERTIFICATE OF CONFORMANCE

ADDITIONAL INFORMATION FOR MIL-STD-656:

INTERIM CHANGES TO MIL-STD-656C

PAGE 18, DEFECT XV. POCKET OR FLAPS, S.

HIP POCKET: ADD NEW DEFECT:

"3. CORD (WELTS) OUT OF HORIZONTAL ALIGNMENT

WITH WAISTBAND WHEN MEASURED FROM BOTTOM OF

WAISTBAND TO TOP CORNERS OF WELT BY:

. D S U

-MORE THAN 1/2 INCH * 3 2

-MORE THAN 1/4 UP TO 1/2 INCH 3 3 2

-UP TO 1/8 MORE 1/4 INCH 2 2 1

INTERIM CHANGES TO MIL-STD-656C:

PAGE 5, TABLE I DELETE IN ITS ENTIRETY AND

SUBSTITUTE "TABLE I SAMPLING PROVISIONS FOR END

ITEM VISUAL EXAMINATION OF DRESS (D) SLACKS:

NORMAL INSPECTION:

LOT SIZE SAMP SIZE MAX ACCP PT VALUE

. 3&2 PT 3.2 &1 PT

. DEFECTS DEFECTS

UP THRU 90 20 3 PT 6 PT

91 - 150 32 5 PT 9 PT

151 - 280 50 7 PT 13 PT

281 - 500 80 9 PT 17 PT

501 - 1200 125 14 PT 25 PT

1201 - 3200 200 18 PT 33 PT

REINSTATE NORMAL INSPECTION (SEE 5.5.4B). THE

3201 - 10,000 315 24 PT 48 PT

SECOND VALUE IS THE MAXIMUM ACCEPTABLE POINT

10,001 - 35,000 500 35 PT 72 PT

35,001 AND OVER 800 55 PT 110 PT

TIGHTENED INSPECTION:

UP THRU 150 32 2 PT 5 PT

151 - 280 50 3 PT 7 PT

281 - 500 80 5 PT 11 PT

501 - 1200 125 9 PT 17 PT

1201 - 3200 200 13 PT 26 PT

3201 - 10,000 315 20 PT 39 PT

10,001 - 35,000 500 30 PT 59 PT

35,001 AND OVER 800 45 PT 89 PT

REDUCED INSPECTION:

UP THRU 280 20 2-6 PT 11 PT

281 - 500 32 3-9 PT 15 PT

501 - 1200 50 5-10 PT 18 PT

1201 - 3200 80 8-13 PT 24 PT

3201 - 10,000 125 12-17 PT 28 PT

10,001 - 35,000 200 17-21 PT 33 PT

35, 001 AND OVER 315 23-29 PT 47 PT

1/ IF THE FIRST VALUE IS EXCEEDED BUT THE SECOND

VALUE HAS NOT BEEN EXCEEDED, ACCEPT THE LOT BUT

REINSTATE NORMAL INSPECTION (SEE 5.5.4B). THE

SECOND VALUE IS THE MAXIMUM ACCEPTABLE POINT

VALUE.

TABLE II DELETE IN ITS ENTIRETY AND SUBSTITUTE

"TABLE II SAMPLING PROVISIONS FOR END ITEM

VISUAL EXAMINATION OF SEMI-DERSS (SD) SLACKS"

NORMAL INSPECTION:

LOT SIZE SAMP SIZE MAX ACCP PT VALUE

. 3&2 PT 3.2.&1 PT

. DEFECTS DEFECTS

UP THRU 500 50 7 PT 14 PT

501 THRU 1200 80 9 PT 20 PT

1201 THRU 3200 125 14 PT 26 PT

3201 THRU 10,000 200 19 PT 38 PT

10,001 THRU 35,000 315 27 PT 57 PT

35,001 AND OVER 500 41 PT 85 PT

TIGHTENED INSPECTION:

UP THRU 500 50 3 PT 10 PT

501 THRU 1200 80 5 PT 15 PT

1201 THRU 3200 125 8 PT 23 PT

3201 THRU 10,000 200 12 PT 34 PT

10,001 THRU 35,000 315 19 PT 52 PT

35,001 AND OVER 500 27 PT 78 PT

REDUCED INSPECTION:

UP THRU 1200 32 3-8 PT 15 PT

1200 THRU 3200 50 5-9 PT 18 PT

3201 THRU 10,000 80 8-12 PT 24 PT

10,001 THRU 35,000 125 11-15 PT 31 PT

35,001 AND OVER 200 15-53 PT 43 PT

1/ IF THE FIRST VALUE IS EXCEEDED BUT THE SECOND

VALUE HAS NOT BEEN EXCEEDED, ACCEPT THE LOT BUT

REINSTATE NORMAL INSPECTION (SEE 5.5.4B). THE

SECOND VALUE IS THE MAXIMUM ACCEPTABLE POINT

VALUE.

TABLE III DELETE IN ITS ENTIRETY AND SUBSTITUTE

"TABLE III SAMPLING PROVISIONS FOR END ITEM

VISUAL EXAMINATION OF UTILITY (U) SLACKS"

NORMAL INSPECTION:

LOT SIZE SAMP SIZE MAX ACCP PT VALUE

. 3&2 PT 3.2 & 1 PT

. DEFECTS DEFECTS

UP THRU 500 50 9 PT 17 PT

501 THRU 1200 80 13 PT 20 PT

1201 THRU 3200 125 18 PT 29 PT

3201 THRU 10,000 200 25 PT 42 PT

10,001 AND OVER 315 39 PT 62 PT

TIGHTENED INSPECTION:

UP THRU 500 50 5 PT 11 PT

501 THRU 1200 80 8 PT 17 PT

1201 THRU 3200 125 12 PT 25 PT

3201 THRU 10,000 200 19 PT 38 PT

10,001 AND OVER 315 27 PT 57 PT

REDUCED INSPECTION:

UP THRU 1200 32 5-9 PT 16 PT

1201 THRU 3200 50 8-12 PT 20 PT

3201 THRU 10,000 80 11-14 PT 25 PT

10,001 AND OVER 125 15-19 PT 29 PT

1/ IF THE FIRST VALUE IS EXCEEDED BUT THE SECOND

VALUE HAS NOT BEEN EXCEEDED, ACCEPT THE LOT BUT

REINSTATE NORMAL INSPECTION (SEE 5.5.4B). THE

SECOND VALUE IS THE MAXIMUM ACCEPTABLE POINT

VALUE.

PAGE 20, UNDER XX LABEL ADD THE FOLLOWING:

D. BAR CODE LABEL/TAG

DEFECT POINT VALUE

. D SD U

1. BAR CODE OMITTED OR NOT

. READABLE BY SCANNER. 1 1 1

2. HUMAN READABLE INTERPRETATION

. (HRI) OMITTED OR

. ILLEGIBLE 1 1 1

3. NOT VISIBLE ON FOLDED,

. PACKAGED ITEM. 1 1 1

4. CAUSES DAMAGE TO THE

. ITEM. 3 3 3".

(Ref. T0320)

ADDITIONAL INFORMATION FOR MIL-STD-984:

MIL-STD-984A: PROVISION FOR SIZE LABELING FOR

WOMEN'S UNIFORM CLOTHING 13 SEPT 1994.

EACH WOMAN'S ITEM SHALL HAVE A SEPARATE

SIZE LABEL CONFORMING TO TYPE VI CLASS 2 OF

MIL-DTL-32075 AND BODY DIMENSION LABELING

REQUIREMENT CONFORMING TO MIL-STD-984. THE

LABEL SHALL INDICATE SIZE, BODY DIMENSIONS,

AND STOCK NUMBER AS SHOWN BELOW:

FOR DRESS COATS:

SIZE CODE: 12JP (EXAMPLE)

BUST CIRC: 37-1/2 (EXAMPLE)

HIP CIRC: 38 (EXAMPLE)

HEIGHT: LESS THAN 63 1/2 (P) (EXAMPLE)

FOR SLACKS AND SKIRTS:

SIZE CODE: 12 JP (EXAMPLE)

WAIST CIRC: 29-1/2 (EXAMPLE)

HIP CIRC: 38 (EXAMPLE)

HEIGHT: LESS THAN 63 1/2 (P) (EXAMPLE)

PAGE 5, TABLE 1, ADD THE FOLLOWING SIZES:

HEIGHT: LESS THAN 63 1/2 (P) (EXAMPLE)

STOCK NO: 8410-00-000-0000 (EXAMPLE)

NOTE: ABBREVIATIONS FOR THE APPLICABLE BODY TYPE

SHALL BE "J" FOR JUNIORS , "M" FOR MISSES AND

"W" FOR WOMEN'S.

ABBREVIATIONS FOR THE APPLICABLE LENGTHS SHALL

BE "P" FOR PETITE, "R" FOR REGULAR, AND "T" FOR

TALL.

NOTE: THE INFORMATION FOR EACH SIZE LABEL IS

CONTAINED IN MIL-STD-984 AND IS NOT TO BE

CONFUSED WITH THE FINISHED DIMENSIONS OF THE END

ITEM IN THE SPECIFICATION.

INTERIM CHANGES TO MIL-STD-984:

PAGE 5, TABLE I, DELETE IN ITS ENTIRETY AND

SUBSTITUTE THE FOLLOWING:

SIZE CODE BUST CIRC WAIST CIRC HIP CIRC

INCHES INCHES INCHES INCHES

2M 31-1/2 23-1/2 34 4J 32-1/2 24-1/2 33 4M 32-1/2 24-1/2 35 4W 32-1/2 24-1/2 37 6J 33-1/2 25-1/2 34 6M 33-1/2 25-1/2 36 6W 33-1/2 25-1/2 38 8J 34-1/2 26-1/2 35 8M 34-1/2 26-1/2 37 8W 34-1/2 26-1/2 39 10J 36 28 36-1/2 10M 36 28 38-1/2 10W 36 28 40-1/2 12J 37-1/2 29-1/2 38 12M 37-1/2 29-1/2 40 12W 37-1/2 29-1/2 42 14J 39 31 39-1/2 14M 39 31 41-1/2 14W 39 31 43-1/2 16J 41 33 41-1/2 16M 41 33 43-1/2 16W 41 33 45-1/2

18J 43 35 43-1/2 18M 43 35 45-1/2 18W 43 35 47-1/2 20J 45 37 45-1/2 20M 45 37 47-1/2 20W 45 37 49-1/2 22J 47 39 47-1/2 22M 47 39 49-1/2 22W 47 39 51-1/2 24J 49 41 49-1/2 24M 49 41 51-1/2 24W 49 41 53-1/2 26J 51 43 51-1/2 26M 51 43 53-1/2 26W 51 43 55-1/2 28J 53 45 53-1/2 28M 53 45 55-1/2 28W 53 45 57-1/2

ADDITIONAL INFORMATION FOR MIL-C-44296:

INTERIM SPECIFICATION CHANGES TO MIL-C-44296A:

PAGE 1, PARAGRAPH 1.1, SCOPE., LINE 1: AFTER "AND" INSERT "STITCH-REINFORCED

NONWOVEN".

PAGE 1, PARAGRAPH 1.2, LINE 12: BETWEEN "TYPE X-CIRCULAR KNIT SUBSTRATE" AND "CLASS 1"

INSERT "TYPE X1- "STITCH-REINFORCED NONWOVEN".

PAGE 1, PARAGRAPH 1.2. CLASSIFICATION. BELOW "TYPE IX" ADD "TYPE X - CIRCULAR KNIT

SUBSTRATE"

PAGE 2, PARAGRAPH 2. APPLICABLE DOCUMENTS ADD FOLLOWING NEW PARAGRAPH: "2.1.3 OTHER

PUBLICATIONS. THE FOLLOWING DOCUMENTS FORM A PART OF THIS DOCUMENT TO THE EXTENT

SPECIFIED HEREIN. UNLESS OTHERWISE SPECIFIED, THE ISSUES OF THE DOCUMENTS WHICH ARE

DOD ADOPTED SHALL BE THOSE LISTED IN THE ISSUE OF THE DODISS SPECIFIED IN THE

SOLICITATION. UNLESS OTHERWISE SPECIFIED, THE ISSUES OF THE DOCUMENTS NOT LISTED IN THE DODISS SHALL BE THE ISSUES OF THE NONGOVERNMENT DOCUMENTS WHICH ARE CURRENT ON THE

DATE OF THE SOLICITATION.

AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS (AATCC) AATCC 20 - FIBER

ANALYSIS QUALITATIVE (APPLICATIONS FOR COPIES SHOULD BE ADDRESSED TO AMERICAN

ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS (AATCC), P.O. BOX 12215, TRIANGLE PARK, NC 27709-2215)"

PAGE 3, ADD THE FOLLOWING NEW PARAGRAPH: "3.1.2.10 TYPE X. TYPE X SHALL BE A CIRCULAR

KNIT. WHEN SPECIFIED (SEE 6.2), THE FACE SIDE SHALL BE NAPPED."

PAGE 3: AFTER PARAGRAPH 3.1.2.10,ADD THE FOLLOWING: "3.1.2.11 TYPE X1. TYPE X1 SHALL

BE STITCH- REINFORCED NONWOVEN WHEREBY A SERIES OF CHAINSTITCHING IS SEWN IN THE

MACHINE DIRECTION OF THE SUBSTRATE IN ORDER TO REINFORCE THE NONWOVEN CONSTRUCTION."

PAGE 7, PARAGRAPH 3.4. PHYSICAL REQUIREMENTS. ADD THE FOLLOWING NEW TABLE AFTER TABLE

VII:

"TABLE VII. A PHYSICAL REQUIREMENTS FOR TYPE X

STYLE CLASS WEIGHT (INCLUDING BURSTING

ADHESIVE) STRENGTH

OZ/SQ/YD. LBS. (MIN.

MINIMUM MAXIMUM

A 1,2,3 OR 4 1.4 1.8 60

FIBER CONTENT

1/

1/ 100% NYLON OR POLYESTER."

PAGE 7,PARAGRAPH 3.4 PHYSICAL REQUIREMENTS.: AFTER TABLE"V111" ADD NEW TABLE 1X:

"TABLE 1X,PHYSICAL REQUIREMENTS FOR TYPE X1

BREAKING STRENGTH

WGT, OZ/YD2 LBS, (MIN) STITCHING

STYLE CLASS MIN MAX MACH X-MACH CONTENT REIN

FORCEMENT

A 1,2,3 1.0 1.8 10.0 1.0 1/ 2/

1/ 50 TO 100 PERCENT POLYESTER WITH REMAINING PERCENTAGE NYLON OR RAYON.

2/ STITCH REINFORCEMENT CONDUCTED WITH SINGLE MULTIFILAMENT THREAD USING CHAINSTITCH

STITCH TYPE WITH CHAINSTITCH LOOPS ON FUSIBLE SIDE TO PROTECT FROM UNRAVELING."

PAGE 7, PARAGRAPH 3.4.1. BONDING STRENGTH.

- LINE 2, DELETE "(EXCEPT CLASS 5)" AND SUBSTITUTE "(EXCEPT TYPE IX WHEN USED AS

FUSIBLE SEAM TAPE AND CLASS 5)".

- LINES 7 AND 8, DELETE "OR SHEETING MATERIAL".

PAGE 9, PARA. 4.2.2.1, LINE 22, DELETE "30" AND SUBSTITUTE "20". LINE 24, DELETE "45"

AND SUBSTITUTE "30".

PAGE 11, TABLE VIII. END ITEM TESTS UNDER TEST METHOD COLUMN, LINES 2 AND 3 DELETE

"1600" AND SUBSTITUTE "AATCC 20".

PAGE 12, PARAGRAPH 4.3.1.1. BONDING STRENGTH PROCEDURE (INITIAL AND AFTER

LAUNDERING/DRY CLEANING). DELETE THE FIRST AND SECOND SENTENCES IN THEIR ENTIRETY AND SUBSTITUTE: "CUT A 12 INCH WARP BY 11 INCH FILLING SAMPLE FROM BOTH THE OUTERSHELL AND

FUSIBLE MATERIALS SPECIFIED FOR CONTRACT USE (SEE 6.5)."

PAGE 15: AT THE END OF PARAGRAPH 6.1.1,ADD THE FOLLOWING:

" E. STITCH REINFORCED NONWOVEN TYPE X1 OFFERS HIGH DEGREE STRENGTH/STABILIZATION FOR TAPE AND STAY APPLICATION FOR LARGE OR SMALL PART FUSIBLES AND IS INTENDED TO PROVIDE

VERTICAL STABILITY AND ABRASION RESISTANCE."

PAGE 16, PARAGRAPH 6.5. BONDING STRENGTH DISPUTE PROCEDURE. INSERT THE FOLLOWING

BETWEEN THE FIRST AND SECOND SENTENCES: "IN SOME CASES, OUTERSHELL SAMPLES

REPRESENTATIVE OF SEPARATE PRODUCTION LOTS MAY BE USED TO DETERMINE IF DIFFERENT

FINISHES MAY AFFECT BONDING STRENGTH."

(ref. T0998 - 5/23/06)

MIL-DTL-32075: LABEL FOR CLOTHING, EQUIPAGE,

AND TENTAGE, GENERAL USE REPLACES DDD-L-20

(Ref. T0451 - June 19, 2007)

INTERIM SPECIFICATION CHANGES TO MIL-DTL-32075:

PAGE 4, PARA. 3.3.5, AFTER "TYPE III OR IV, CLASS 4 OF" DELETE "DDD-L-20" AND REPLACE

"MIL-DTL-32075,".

PAGE 6, TABLE I, "PHYSICAL REQUIREMENTS OF THE

TYPE VI FINISHED LABEL." UNDER "TEARING

STRENGTH" DELETE: "(LB.) MINIMUM" AND

SUBSTITUTE: "(GNS) MINIMUM."

PAGE 12, PARA 3.3.2.17, AFTER "NSN" ADD

"AND THE UNIVERSAL PRODUCT CODE (UPC)

SUPPLIED BY THE GOVERNMENT, FOR ALL NSNs."

INTERIM SPECIFICATION CHANGES TO MIL-C-44296A:

PAGE 1, PARAGRAPH 1.1, SCOPE., LINE 1: AFTER

"AND" INSERT "STITCH-REINFORCED NONWOVEN".

PAGE 1, PARAGRAPH 1.2, LINE 12: BETWEEN

"TYPE X-CIRCULAR KNIT SUBSTRATE" AND "CLASS 1"

INSERT "TYPE X1- "STITCH-REINFORCED NONWOVEN".

PAGE 1, PARAGRAPH 1.2. CLASSIFICATION. BELOW

"TYPE IX" ADD "TYPE X - CIRCULAR KNIT SUBSTRATE"

PAGE 2, PARAGRAPH 2. APPLICABLE DOCUMENTS ADD

FOLLOWING NEW PARAGRAPH: "2.1.3 OTHER

PUBLICATIONS. THE FOLLOWING DOCUMENTS FORM A

PART OF THIS DOCUMENT TO THE EXTENT SPECIFIED

HEREIN. UNLESS OTHERWISE SPECIFIED,THE ISSUES OF

THE DOCUMENTS WHICH ARE DOD ADOPTED SHALL BE

THOSE LISTED IN THE ISSUE OF THE DODISS

SPECIFIED IN THE SOLICITATION. UNLESS OTHERWISE

SPECIFIED, THE ISSUES OF THE DOCUMENTS NOT

LISTED IN THE DODISS SHALL BE THE ISSUES OF THE

NONGOVERNMENT DOCUMENTS WHICH ARE CURRENT ON THE

DATE OF THE SOLICITATION.

AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND

COLORISTS (AATCC) AATCC 20 - FIBER ANALYSIS

QUALITATIVE (APPLICATIONS FOR COPIES SHOULD BE

ADDRESSED TO AMERICAN ASSOCIATION OF TEXTILE

CHEMISTS AND COLORISTS (AATCC), P.O. BOX 12215,

TRIANGLE PARK, NC 27709-2215)"

PAGE 3, ADD THE FOLLOWING NEW PARAGRAPH:

"3.1.2.10 TYPE X. TYPE X SHALL BE A CIRCULAR

KNIT. WHEN SPECIFIED (SEE 6.2), THE FACE SIDE

SHALL BE NAPPED."

PAGE 3: AFTER PARAGRAPH 3.1.2.10,ADD THE

FOLLOWING:

"3.1.2.11 TYPE X1. TYPE X1 SHALL BE STITCH-

REINFORCED NONWOVEN WHEREBY A SERIES OF

CHAINSTITCHING IS SEWN IN THE MACHINE

DIRECTION OF THE SUBSTRATE IN ORDER TO

REINFORCE THE NONWOVEN CONSTRUCTION."

PAGE 7, PARAGRAPH 3.4. PHYSICAL REQUIREMENTS.

ADD THE FOLLOWING NEW TABLE AFTER TABLE VII:

"TABLE VII. A PHYSICAL REQUIREMENTS FOR TYPE X

STYLE CLASS WEIGHT (INCLUDING BURSTING

. ADHESIVE) STRENGTH

. OZ/SQ/YD. LBS. (MIN.

. MINIMUM MAXIMUM

A 1,2,3 OR 4 1.4 1.8 60

FIBER CONTENT

1/

1/ 100% NYLON OR POLYESTER."

PAGE 7,PARAGRAPH 3.4 PHYSICAL REQUIREMENTS.:

AFTER TABLE"V111" ADD NEW TABLE 1X:

"TABLE 1X,PHYSICAL REQUIREMENTS FOR TYPE X1

. BREAKING STRENGTH

. WGT, OZ/YD2 LBS, (MIN) STITCHING

STYLE CLASS MIN MAX MACH X-MACH CONTENT REIN

. FORCEMENT

. A 1,2,3 1.0 1.8 10.0 1.0 1/ 2/

1/ 50 TO 100 PERCENT POLYESTER WITH REMAINING

PERCENTAGE NYLON OR RAYON.

2/ STITCH REINFORCEMENT CONDUCTED WITH SINGLE

MULTIFILAMENT THREAD USING CHAINSTITCH STITCH

TYPE WITH CHAINSTITCH LOOPS ON FUSIBLE SIDE TO

PROTECT FROM UNRAVELING."

PAGE 7, PARAGRAPH 3.4.1. BONDING STRENGTH.

- LINE 2, DELETE "(EXCEPT CLASS 5)" AND

SUBSTITUTE "(EXCEPT TYPE IX WHEN USED AS FUSIBLE

SEAM TAPE AND CLASS 5)".

- LINES 7 AND 8, DELETE "OR SHEETING MATERIAL".

PAGE 9, PARA. 4.2.2.1, LINE 22, DELETE "30" AND

SUBSTITUTE "20". LINE 24, DELETE "45" AND

SUBSTITUTE "30".

PAGE 11, TABLE VIII. END ITEM TESTS UNDER TEST

METHOD COLUMN, LINES 2 AND 3 DELETE "1600" AND

SUBSTITUTE "AATCC 20".

PAGE 12, PARAGRAPH 4.3.1.1. BONDING STRENGTH

PROCEDURE (INITIAL AND AFTER LAUNDERING/DRY

CLEANING). DELETE THE FIRST AND SECOND SENTENCES

IN THEIR ENTIRETY AND SUBSTITUTE: "CUT A 12 INCH

WARP BY 11 INCH FILLING SAMPLE FROM BOTH THE

OUTERSHELL AND FUSIBLE MATERIALS SPECIFIED FOR

CONTRACT USE (SEE 6.5)."

PAGE 15: AT THE END OF PARAGRAPH 6.1.1,ADD THE

FOLLOWING:

" E. STITCH REINFORCED NONWOVEN TYPE X1 OFFERS

HIGH DEGREE STRENGTH/STABILIZATION FOR TAPE AND

STAY APPLICATION FOR LARGE OR SMALL PART

FUSIBLES AND IS INTENDED TO PROVIDE VERTICAL

STABILITY AND ABRASION RESISTANCE."

PAGE 16, PARAGRAPH 6.5. BONDING STRENGTH DISPUTE

PROCEDURE. INSERT THE FOLLOWING BETWEEN THE

FIRST AND SECOND SENTENCES: "IN SOME CASES,

OUTERSHELL SAMPLES REPRESENTATIVE OF SEPARATE

PRODUCTION LOTS MAY BE USED TO DETERMINE IF

DIFFERENT FINISHES MAY AFFECT BONDING STRENGTH."

ADDITIONAL INFORMATION FOR A-A-52094A THREAD, COTTON

NO ADDITIONAL INFORMATION

(ref. T1481)

ADDITIONAL INFORMATION FOR A-A-52106:

INTERIM CHANGES TO A-A-52106:

PAGE 1, UNDER ABSTRACT. AFTER "THE CLASS 3 CLOTH IS

INTENDED FOR USE AS LINING MATERIAL IN DRESS COATS."

ADD "CLASS 4 CLOTH IS INTENDED TO BE USED AS A

GARMENT LINING. CLASS 5 CLOTH IS INTENDED FOR USE

AS A NECKTIE AND NECKTAB OUTERSHELL FABRIC."

PAGE 1, CLASSIFICATION. ADD CLASS 4 - LIGHT WEIGHT

2.4 OZ; 2/1 RIGHT HAND TWILL USING 100% FILAMENT

POLYESTER SINGLE PLY YARNS FOR BOTH CLASS 4 AND CLASS 5.

CLASS 5 - MEDIUM WEIGHT 3.0 OZ; 5/1 HERRINGBONE TWILL

PAGE 1, PARAGRAPH 1.1 CLASSIFICATION: ADD PAGE 1,

GENERAL DESCRIPTION. LINE 5 AFTER "YARNS" ADD

"THE CLASS 4 CLOTH SHALL BE A TW0 UP-ONE DOWN RIGHT

HAND TWILL. THE CLASS 5 CLOTH SHALL BE A FIVE UP-ONE

DOWN HERRINGBONE TWILL. THE YARNS FOR CLASS 4 CLOTH

SHALL BE SINGLE PLY WITH A NOMINAL DENIER OF 70 FOR

THE WARP YARNS AND 150 FOR THE FILLING YARNS.

PAGE 2, TABLE I CLOTH REQUIREMENTS AFTER CLASS 3"

ADD INFORMATION FOR "CLASSES 4 AND 5"

CHARACTERISTIC CLASS 4 CLASS 5

MATERIAL CONTENT, PERCENT:

POLYESTER 100% 100%

COTTON 0 0

RAYON 0 0

COLORFASTNESS TO:

PERSPIRATION GOOD GOOD

SUBLIMATION GOOD GOOD

WET DRY-CLEANING GOOD GOOD

CROCKING (MIN.) 3.5 3/ 3.5 3/

(BLACK OR DARK

BLUE COLORS) 1.0 3/ 1.0 3/

LABILE SULFUR CONTENT 4/ 4/

WEIGHT, OZ. /SQ. YD.(MIN.) 2.4 3.0

YARNS PER INCH (MIN.)

WARP 124 140

FILLING 76 75

BREAKING STRENGTH POUNDS (MIN.)

WARP 140 160

FILLING 110 130

TEARING STRENGTH POUNDS (MIN.)

WARP 5.0 14.0

FILLING 3.0 10.5

PAGE 2, PARAGRAPH 2.1 GENERAL DESCRIPTION: AFTER

"THE CLASS 5 CLOTH SHALL BE A FIVE UP-ONE DOWN

"THE CLASS 5 CLOTH, USING 100 % FILAMENT HERRINGBONE

TWILL." INSERT "THE CLASS 6 CLOTH POLYESTER SINGLE PLY

WITH BLACK 70 DENIER NOMINAL WARP AND AIR FORCE

BLUE 1622 150 DENIER NOMINAL FILLING YARNS." USING

100% FILAMENT POLYESTER SINGLE PLY WITH 70 DENIER NOMINAL

IN THE WARP AND 150 DENIER NOMINAL IN THE FILLING DIRECTION."

PAGE 2, PARAGRAPH 2.2 PHYSICAL REQUIREMENTS:

TABLE I. CLOTH REQUIREMENTS, ADD THE FOLLOWING:

PAGE 3, AFTER 2.3 LENGTH AND PUT-UP. ADD THE FOLLOWING

NEW PARAGRAPH: "2.4 COLOR. THE COLOR OF THE FINISHED

CLOTH SHALL BE AS SPECIFIED (SEE 5.1) AND SHALL MATCH THE STANDARD SAMPLE FOR SHADE.

CLASS 5 FABRIC IS MADE

FROM DYED WARP AND DYED FILLING IN TWO DIFFERENT COLORS.

CLASS 5 FABRIC SHALL BE AIR FORCE SHADE BLUE 1622 ROLL #89-2.

(ref. T1514 - 5/23/06)

ADDITIONAL INFORMATION FOR A-A-52108:

NO ADDITIONAL INFORMATION FOLLOWS.

ADDITIONAL INFORMATION FOR A-A-55634A, 23 MARCH 2004:

SPECIAL NOTE!! ALL SLIDE FASTENERS USED ARE TO BE MEASURED FROM "STOP TO STOP".

RECOMMEND THAT THIS MEASUREMENT BE TAKEN RANDOMLY BEFORE SLIDE FASTENERS ARE SEWN TO

THE ITEMS, COVERALL, OR ANY ITEM REFERRED TO IN THE SOLICITATION. "THE QAR WILL

REJECT ANY SLIDE THAT IS NOT LAYING FLAT AFTER IT IS SEWN INTO/ONTO AN ITEM." SPECIAL INFO ON ITEMS THAT UTILIZE SLIDE FASTENERS IS GIVEN BY "ALL USING MILITARY PERSONNEL".

ADDITIONAL INFORMATION FOR V-B-871: NO ADDITIONAL INFORMATION FOLLOWS.

MIL-STD-129R - DEPARTMENT OF DEFENSE STANDARD PRACTICE

- MILITARY MARKING FOR SHIPMENT AND STORAGE

DATED 18 FEBRUARY 2014

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE MATERIAL) SHALL

BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA TROOP SUPPORT C&T ITEMS,

REGARDLESS OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER TO BE LOADED FOR EACH SHIPMENT. THE WORDS

"PACKING LIST HERE" SHALL BE STENCILED, NOT HAND LETTERED, ON THE CONTAINER.

NOTE: UNIVERSAL PRODUCT CODE INFORMATION THE GOVERMENT ASSIGNED UNIVERSAL PRODUCT CODE

(UPC) MUST BE PLACED ON ALL SHIPPING CARTONS ON WHICH THE NSN APPEARS.

THE FOLLOWING DEFECTS APPLY FOR BARCODE LABELS/TAGS:

BAR CODE OMITTED OR NOT READABLE BY SCANNER

HUMAN-READABLE INTERPRETATION (HRI) OMITTED OR ILLEGIBLE

NOT VISIBLE ON FOLDED, PACKAGED ITEM CAUSES DAMAGE TO THE ITEM

MIL-STD-147E

w/CHANGE 1 23 December 2013

SUPERSEDING

MIL-STD-147E

16 May 2008

DEPARTMENT OF DEFENSE

STANDARD PRACTICE

PALLETIZED UNIT LOADS

ADDITIONAL INFORMATION FOR ANSI/ASQC Z1.4:

NOTE: THE MOST RECENT VERSION OF THIS DOCUMENT SHOULD BE USED.

APPLICATION FOR COPIES SHOULD BE ADDRESSED TO:

AMERICAN SOCIETY FOR QUALITY

600 NORTH PLANKINTON AVENUE

MILWAUKEE, WISCONSIN 53203

(Ref. T0795 - May 17, 2006)ACCEPTABILITY OF LOTS SHALL BE DETERMINED BY THE USE OF

"SAMPLING PROCEDURES AND TABLES FOR INSPECTION BY ATTRIBUTES",

ANSI/ASQC Z1.4

GENERAL INSPECTION LEVEL 2

AQL's FOR PURCHASE DESCRIPTION

END ITEM DIMENSIONAL 4.0

VISUAL 6.5