ATTACH_Tech_Data_03522.pdf

SLACKS, WOMAN'S, SERVICE DRESS BLUE SHALL BE MADE IN ACCORDANCE WITH

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL

AND QUALITY REQUIREMENTS FOUND ON THE WEB AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE

MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT

INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

CG/PD 11-04A DATE, 10 March 2014.

PATTERN DATE: 30 SEPT 2010

FINISHED MATERIAL SHALL MATCH THE STANDARD SAMPLE FOR COAST GUARD BLUE 3362, ROLL # 9-

310611 FOR SHADE ONLY.

THE CONTRACTOR SHALL STAMP LEGIBLY WITH INDELIBLE INK THE LOT NUMBER ON EACH END ITEM

AND OUTER CONTAINER IN THE LOT.

LIST OF DOCUMENTS, EXHIBITS, AND OTHER ATTACHMENTS

A. THIS SOLICITATION/AWARD CONSISTS OF THE FOLLOWING DOCUMENTS, EXHIBITS, AND OTHER

ATTACHMENTS.

B. DLA TROOP SUPPORT CLOTHING AND TEXTILES #ADDITIONAL QUALITY ASSURANCE REQUIREEMENTS

DATED OCTOBER 2018#, SUPERSEDES DSCP 4155.3, QUALITY SYSTEMS REQUIREMENTS, DATED

NOVEMBER 3, 1997.

c. DLA Troop Support Clothing and Textiles Additional Quality Assurance Requirements dated October 2018 additional changes:

Page 10 of 38, par. 2.1, line 4, after "(DCMA QAS)" add ", or Supplier's Source Sampling Representative, as applicable"

Page 11 of 38, par. 2.3, line 2, delete "to the source QAS". Line 4, delete "source QAS" and replace with "Supplier's Source Sampling Representative". Page 12, par 2.3 (continued), delete "source QAS" and replace with "Supplier's Source Sampling Representative".

Page 12 of 38, par. 2.4, line 5, delete "as required" and replace with "if required".

Page 12 of 38, par. 3.1.1, after "entirely" add the following: "For routine shade or physical testing of fabric lots, Government sampling is not required. The DD Form 1222 for routine shade or physical testing of fabric lots shall be signed and dated by the Supplier's Source Sampling Representative in Box 15."

Page 13 of 38, par. 3.1.2 - line 10, after "Government QAS" add the following: "or Supplier's Source Sampling Representative, as applicable,"

Page 14 of 38, par. 3.2.1 -line 4, delete "source QAS" and replace with "Supplier's Source Sampling Representative".

Page 14 of 38, par. 3.2.1.1 - cutting swatches, delete "DCMA QAS" and replace with "Supplier's Source Sampling Representative". After "single color rolls - 4"x 24"" delete "QAS" and replace with "Supplier's Source Sampling Representative". After "multi-color camouflage"... delete "QAS" and replace with "Supplier's Source Sampling Representative".

Page 14 of 38, par. 3.2.1.2 - line 3, delete "stamped,". Line 4, Delete "source QAS" and replace with "Supplier's Source Sampling Representative"

Page 15 of 38, par. 3.2.1.4 - subpar. 2, delete "source QAS" and replace with "Supplier's Source Sampling Representative"

Page 15 of 38, par. 3.2.2 - Line 3, delete "stamped,", delete "source QAS" and replace with "Supplier's Source Sampling Representative". Line 4, delete "QAS" and replace with "Supplier's Source Sampling Representative".

Page 16 of 38, par. 3.3.1 - Line 2, after "(30)" add, "calendar". Line 3 and Line 6, after "QAS" add, "or Supplier's Source Sampling Representative"

Page 16 of 38, par. 3.3.2 - Delete the paragraph in its entirety, including subparagraphs labeled "a" through "i", and replace with the following:

"3.3.2. Contractor Furnished Material (CFM). DLA Troop Support Clothing and Textiles contracts require source sampling of CFM at finishing plants. The following provisions apply to sample selection and lot acceptance.

(a) The samples shall be randomly selected by the Supplier's Source Sampling Representative.

(b) Upon presentation of a lot, the Supplier's Source Sampling Representative will draw samples and forward the samples to the contractor's laboratory specified in the contract for testing.

(c) Shipment of Component Lots from the source to the prime contractor need not be deferred except for Government Acceptance Testing (i.e., shade evaluation).

Commencement of production prior to receipt of a passing test report from the contractor's authorized laboratory is solely at the contractor's risk.

(d) The contractor will provide copies of Certificates of Compliance to the QAS.

(e) The contractor is required to ensure that a complete test report for all lots is furnished to the source's QAS and the appropriate DLA-PTC representative."

Pages 24, 25, 36 add to block 16: "By signing in box 15, I certify that the samples referenced above were randomly selected and represent the lot identified above.

**Special note: Contractors shall ensure that blocks 2 and 15 of the form DD1222 are updated to reflect the correct information. Historically, both blocks contained the information of the DCMA QAR and their stamp/signature. When contractor's representative samples, these blocks shall include the contractor's representative's information. Block 17 shall still include the DCMA QAR to receive the results of the report even though they may not be sampling the material to be tested.

Page 5, after paragraph "3.5.2" insert the following paragraph:

"3.5.3 Each pair of slacks shall have the DLA Exclusive Woven Label. The jacquard woven Exclusive label shall specify "Made exclusively for Defense Logistics Agency" and shall include "by" and the contractor's name. The label shall be sewn to the bottom of the waistband opposite the size label, two inches off center back. The proposed finished label's design shall be submitted to the contracting officer for approval."

Page 5, Paragraph 3.7 Patterns, delete in its entirety and substitute, "Paragraph 3.7 Patterns. The Government will furnish a complete set of graded patterns. The pattern provides 1/2 inch for side seams, 1/2 inch for inseams tapered at knee notch to 7/8 inch at crotch for back leg outlet, 3/8 inch seam allowance starting at the crotch and gradually increasing to 1-1/4 inch at seat outlet seam for seat outlet seam, 3/8 inch seam allowance for front crotch, waistband attachment, and fly assemblies, and 1/4 inch for pocket facing and pocket assembly. The working patterns shall be identical to the Government patterns but may be modified to accommodate automation;

however, if the working patterns are modified, the design and measurements must be maintained as intended by this document and the Government patterns."

Page 8, paragraph 3.8.10. Belt loops, line 1, delete "6" and substitute "0", line two, delete "4" and substitute "0", and line 3, delete "22" and substitute "28".

ADDITIONAL INFORMATION FOR MIL-STD-656:

INTERIM CHANGES TO MIL-STD-656C

PAGE 18, DEFECT XV. POCKET OR FLAPS, S.

HIP POCKET: ADD NEW DEFECT:

"3. CORD (WELTS) OUT OF HORIZONTAL ALIGNMENT

WITH WAISTBAND WHEN MEASURED FROM BOTTOM OF

WAISTBAND TO TOP CORNERS OF WELT BY:

. D S U

-MORE THAN 1/2 INCH * 3 2

-MORE THAN 1/4 UP TO 1/2 INCH 3 3 2

-UP TO 1/8 MORE 1/4 INCH 2 2 1

INTERIM CHANGES TO MIL-STD-656C:

PAGE 5, TABLE I DELETE IN ITS ENTIRETY AND

SUBSTITUTE "TABLE I SAMPLING PROVISIONS FOR END

ITEM VISUAL EXAMINATION OF DRESS (D) SLACKS:

NORMAL INSPECTION:

LOT SIZE SAMP SIZE MAX ACCP PT VALUE

. 3&2 PT 3.2 &1 PT

. DEFECTS DEFECTS

UP THRU 90 20 3 PT 6 PT

91 - 150 32 5 PT 9 PT

151 - 280 50 7 PT 13 PT

281 - 500 80 9 PT 17 PT

501 - 1200 125 14 PT 25 PT

1201 - 3200 200 18 PT 33 PT

REINSTATE NORMAL INSPECTION (SEE 5.5.4B). THE

3201 - 10,000 315 24 PT 48 PT

SECOND VALUE IS THE MAXIMUM ACCEPTABLE POINT

10,001 - 35,000 500 35 PT 72 PT

35,001 AND OVER 800 55 PT 110 PT

TIGHTENED INSPECTION:

UP THRU 150 32 2 PT 5 PT

151 - 280 50 3 PT 7 PT

281 - 500 80 5 PT 11 PT

501 - 1200 125 9 PT 17 PT

1201 - 3200 200 13 PT 26 PT

3201 - 10,000 315 20 PT 39 PT

10,001 - 35,000 500 30 PT 59 PT

35,001 AND OVER 800 45 PT 89 PT

REDUCED INSPECTION:

UP THRU 280 20 2-6 PT 11 PT

281 - 500 32 3-9 PT 15 PT

501 - 1200 50 5-10 PT 18 PT

1201 - 3200 80 8-13 PT 24 PT

3201 - 10,000 125 12-17 PT 28 PT

10,001 - 35,000 200 17-21 PT 33 PT

35, 001 AND OVER 315 23-29 PT 47 PT

1/ IF THE FIRST VALUE IS EXCEEDED BUT THE SECOND

VALUE HAS NOT BEEN EXCEEDED, ACCEPT THE LOT BUT

REINSTATE NORMAL INSPECTION (SEE 5.5.4B). THE

SECOND VALUE IS THE MAXIMUM ACCEPTABLE POINT

VALUE.

TABLE II DELETE IN ITS ENTIRETY AND SUBSTITUTE

"TABLE II SAMPLING PROVISIONS FOR END ITEM

VISUAL EXAMINATION OF SEMI-DERSS (SD) SLACKS"

NORMAL INSPECTION:

LOT SIZE SAMP SIZE MAX ACCP PT VALUE

. 3&2 PT 3.2.&1 PT

. DEFECTS DEFECTS

UP THRU 500 50 7 PT 14 PT

501 THRU 1200 80 9 PT 20 PT

1201 THRU 3200 125 14 PT 26 PT

3201 THRU 10,000 200 19 PT 38 PT

10,001 THRU 35,000 315 27 PT 57 PT

35,001 AND OVER 500 41 PT 85 PT

TIGHTENED INSPECTION:

UP THRU 500 50 3 PT 10 PT

501 THRU 1200 80 5 PT 15 PT

1201 THRU 3200 125 8 PT 23 PT

3201 THRU 10,000 200 12 PT 34 PT

10,001 THRU 35,000 315 19 PT 52 PT

35,001 AND OVER 500 27 PT 78 PT

REDUCED INSPECTION:

UP THRU 1200 32 3-8 PT 15 PT

1200 THRU 3200 50 5-9 PT 18 PT

3201 THRU 10,000 80 8-12 PT 24 PT

10,001 THRU 35,000 125 11-15 PT 31 PT

35,001 AND OVER 200 15-53 PT 43 PT

1/ IF THE FIRST VALUE IS EXCEEDED BUT THE SECOND

VALUE HAS NOT BEEN EXCEEDED, ACCEPT THE LOT BUT

REINSTATE NORMAL INSPECTION (SEE 5.5.4B). THE

SECOND VALUE IS THE MAXIMUM ACCEPTABLE POINT

VALUE.

TABLE III DELETE IN ITS ENTIRETY AND SUBSTITUTE

"TABLE III SAMPLING PROVISIONS FOR END ITEM

VISUAL EXAMINATION OF UTILITY (U) SLACKS"

NORMAL INSPECTION:

LOT SIZE SAMP SIZE MAX ACCP PT VALUE

. 3&2 PT 3.2 & 1 PT

. DEFECTS DEFECTS

UP THRU 500 50 9 PT 17 PT

501 THRU 1200 80 13 PT 20 PT

1201 THRU 3200 125 18 PT 29 PT

3201 THRU 10,000 200 25 PT 42 PT

10,001 AND OVER 315 39 PT 62 PT

TIGHTENED INSPECTION:

UP THRU 500 50 5 PT 11 PT

501 THRU 1200 80 8 PT 17 PT

1201 THRU 3200 125 12 PT 25 PT

3201 THRU 10,000 200 19 PT 38 PT

10,001 AND OVER 315 27 PT 57 PT

REDUCED INSPECTION:

UP THRU 1200 32 5-9 PT 16 PT

1201 THRU 3200 50 8-12 PT 20 PT

3201 THRU 10,000 80 11-14 PT 25 PT

10,001 AND OVER 125 15-19 PT 29 PT

1/ IF THE FIRST VALUE IS EXCEEDED BUT THE SECOND

VALUE HAS NOT BEEN EXCEEDED, ACCEPT THE LOT BUT

REINSTATE NORMAL INSPECTION (SEE 5.5.4B). THE

SECOND VALUE IS THE MAXIMUM ACCEPTABLE POINT

VALUE.

PAGE 20, UNDER XX LABEL ADD THE FOLLOWING:

D. BAR CODE LABEL/TAG

DEFECT POINT VALUE

. D SD U

1. BAR CODE OMITTED OR NOT

. READABLE BY SCANNER. 1 1 1

2. HUMAN READABLE INTERPRETATION

. (HRI) OMITTED OR

. ILLEGIBLE 1 1 1

3. NOT VISIBLE ON FOLDED,

. PACKAGED ITEM. 1 1 1

4. CAUSES DAMAGE TO THE

. ITEM. 3 3 3".

(Ref. T0320)

ADDITIONAL INFORMATION FOR MIL-STD-984:

MIL-STD-984A: PROVISION FOR SIZE LABELING FOR

WOMEN'S UNIFORM CLOTHING 13 SEPT 1994.

EACH WOMAN'S ITEM SHALL HAVE A SEPARATE

SIZE LABEL CONFORMING TO TYPE VI CLASS 2 OF

MIL-DTL-32075 AND BODY DIMENSION LABELING

REQUIREMENT CONFORMING TO MIL-STD-984. THE

LABEL SHALL INDICATE SIZE, BODY DIMENSIONS,

AND STOCK NUMBER AS SHOWN BELOW:

FOR DRESS COATS:

SIZE CODE: 12JP (EXAMPLE)

BUST CIRC: 37-1/2 (EXAMPLE)

HIP CIRC: 38 (EXAMPLE)

HEIGHT: LESS THAN 63 1/2 (P) (EXAMPLE)

FOR SLACKS AND SKIRTS:

SIZE CODE: 12 JP (EXAMPLE)

WAIST CIRC: 29-1/2 (EXAMPLE)

HIP CIRC: 38 (EXAMPLE)

HEIGHT: LESS THAN 63 1/2 (P) (EXAMPLE)

PAGE 5, TABLE 1, ADD THE FOLLOWING SIZES:

HEIGHT: LESS THAN 63 1/2 (P) (EXAMPLE)

STOCK NO: 8410-00-000-0000 (EXAMPLE)

NOTE: ABBREVIATIONS FOR THE APPLICABLE BODY TYPE

SHALL BE "J" FOR JUNIORS , "M" FOR MISSES AND

"W" FOR WOMEN'S.

ABBREVIATIONS FOR THE APPLICABLE LENGTHS SHALL

BE "P" FOR PETITE, "R" FOR REGULAR, AND "T" FOR

TALL.

NOTE: THE INFORMATION FOR EACH SIZE LABEL IS

CONTAINED IN MIL-STD-984 AND IS NOT TO BE

CONFUSED WITH THE FINISHED DIMENSIONS OF THE END

ITEM IN THE SPECIFICATION.

INTERIM CHANGES TO MIL-STD-984:

PAGE 5, TABLE I, DELETE IN ITS ENTIRETY AND

SUBSTITUTE THE FOLLOWING:

SIZE CODE BUST CIRC WAIST CIRC HIP CIRC

INCHES INCHES INCHES INCHES

2M 31-1/2 23-1/2 34 4J 32-1/2 24-1/2 33 4M 32-1/2 24-1/2 35 4W 32-1/2 24-1/2 37 6J 33-1/2 25-1/2 34 6M 33-1/2 25-1/2 36 6W 33-1/2 25-1/2 38 8J 34-1/2 26-1/2 35 8M 34-1/2 26-1/2 37 8W 34-1/2 26-1/2 39 10J 36 28 36-1/2 10M 36 28 38-1/2 10W 36 28 40-1/2 12J 37-1/2 29-1/2 38 12M 37-1/2 29-1/2 40 12W 37-1/2 29-1/2 42 14J 39 31 39-1/2 14M 39 31 41-1/2 14W 39 31 43-1/2 16J 41 33 41-1/2 16M 41 33 43-1/2 16W 41 33 45-1/2 18J 43 35 43-1/2 18M 43 35 45-1/2 18W 43 35 47-1/2 20J 45 37 45-1/2 20M 45 37 47-1/2 20W 45 37 49-1/2 22J 47 39 47-1/2 22M 47 39 49-1/2 22W 47 39 51-1/2 24J 49 41 49-1/2 24M 49 41 51-1/2 24W 49 41 53-1/2 26J 51 43 51-1/2 26M 51 43 53-1/2 26W 51 43 55-1/2 28J 53 45 53-1/2 28M 53 45 55-1/2 28W 53 45 57-1/2

"MIL-DTL-32075: LABEL FOR CLOTHING, EQUIPAGE,

AND TENTAGE, GENERAL USE REPLACES DDD-L-20

(Ref. T0451 - June 19, 2007)

INTERIM SPECIFICATION CHANGES TO MIL-DTL-32075:

PAGE 6, TABLE I, "PHYSICAL REQUIREMENTS OF THE

TYPE VI FINISHED LABEL." UNDER "TEARING

STRENGTH" DELETE: "(LB.) MINIMUM" AND

SUBSTITUTE: "(GNS) MINIMUM."

PAGE 12, PARA 3.3.2.17, AFTER "NSN" ADD

"AND THE UNIVERSAL PRODUCT CODE (UPC)

SUPPLIED BY THE GOVERNMENT, FOR ALL NSNs."

INTERIM SPECIFICATION CHANGES TO MIL-C-44296A:

PAGE 1, PARAGRAPH 1.1, SCOPE., LINE 1: AFTER

"AND" INSERT "STITCH-REINFORCED NONWOVEN".

PAGE 1, PARAGRAPH 1.2, LINE 12: BETWEEN

"TYPE X-CIRCULAR KNIT SUBSTRATE" AND "CLASS 1"

INSERT "TYPE X1- "STITCH-REINFORCED NONWOVEN".

PAGE 1, PARAGRAPH 1.2. CLASSIFICATION. BELOW

"TYPE IX" ADD "TYPE X - CIRCULAR KNIT SUBSTRATE"

PAGE 2, PARAGRAPH 2. APPLICABLE DOCUMENTS ADD

FOLLOWING NEW PARAGRAPH: "2.1.3 OTHER

PUBLICATIONS. THE FOLLOWING DOCUMENTS FORM A

PART OF THIS DOCUMENT TO THE EXTENT SPECIFIED

HEREIN. UNLESS OTHERWISE SPECIFIED,THE ISSUES OF

THE DOCUMENTS WHICH ARE DOD ADOPTED SHALL BE

THOSE LISTED IN THE ISSUE OF THE DODISS

SPECIFIED IN THE SOLICITATION. UNLESS OTHERWISE

SPECIFIED, THE ISSUES OF THE DOCUMENTS NOT

LISTED IN THE DODISS SHALL BE THE ISSUES OF THE

NONGOVERNMENT DOCUMENTS WHICH ARE CURRENT ON THE

DATE OF THE SOLICITATION.

AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND

COLORISTS (AATCC) AATCC 20 - FIBER ANALYSIS

QUALITATIVE (APPLICATIONS FOR COPIES SHOULD BE

ADDRESSED TO AMERICAN ASSOCIATION OF TEXTILE

CHEMISTS AND COLORISTS (AATCC), P.O. BOX 12215,

TRIANGLE PARK, NC 27709-2215)"

PAGE 3, ADD THE FOLLOWING NEW PARAGRAPH:

"3.1.2.10 TYPE X. TYPE X SHALL BE A CIRCULAR

KNIT. WHEN SPECIFIED (SEE 6.2), THE FACE SIDE

SHALL BE NAPPED."

PAGE 3: AFTER PARAGRAPH 3.1.2.10,ADD THE

FOLLOWING:

"3.1.2.11 TYPE X1. TYPE X1 SHALL BE STITCH-

REINFORCED NONWOVEN WHEREBY A SERIES OF

CHAINSTITCHING IS SEWN IN THE MACHINE

DIRECTION OF THE SUBSTRATE IN ORDER TO

REINFORCE THE NONWOVEN CONSTRUCTION."

PAGE 7, PARAGRAPH 3.4. PHYSICAL REQUIREMENTS.

ADD THE FOLLOWING NEW TABLE AFTER TABLE VII:

"TABLE VII. A PHYSICAL REQUIREMENTS FOR TYPE X

STYLE CLASS WEIGHT (INCLUDING BURSTING

. ADHESIVE) STRENGTH

. OZ/SQ/YD. LBS. (MIN.

. MINIMUM MAXIMUM

A 1,2,3 OR 4 1.4 1.8 60

FIBER CONTENT

1/

1/ 100% NYLON OR POLYESTER."

PAGE 7,PARAGRAPH 3.4 PHYSICAL REQUIREMENTS.:

AFTER TABLE"V111" ADD NEW TABLE 1X:

"TABLE 1X,PHYSICAL REQUIREMENTS FOR TYPE X1

. BREAKING STRENGTH

. WGT, OZ/YD2 LBS, (MIN) STITCHING

STYLE CLASS MIN MAX MACH X-MACH CONTENT REIN

. FORCEMENT

. A 1,2,3 1.0 1.8 10.0 1.0 1/ 2/

1/ 50 TO 100 PERCENT POLYESTER WITH REMAINING

PERCENTAGE NYLON OR RAYON.

2/ STITCH REINFORCEMENT CONDUCTED WITH SINGLE

MULTIFILAMENT THREAD USING CHAINSTITCH STITCH

TYPE WITH CHAINSTITCH LOOPS ON FUSIBLE SIDE TO

PROTECT FROM UNRAVELING."

PAGE 7, PARAGRAPH 3.4.1. BONDING STRENGTH.

- LINE 2, DELETE "(EXCEPT CLASS 5)" AND

SUBSTITUTE "(EXCEPT TYPE IX WHEN USED AS FUSIBLE

SEAM TAPE AND CLASS 5)".

- LINES 7 AND 8, DELETE "OR SHEETING MATERIAL".

PAGE 9, PARA. 4.2.2.1, LINE 22, DELETE "30" AND

SUBSTITUTE "20". LINE 24, DELETE "45" AND

SUBSTITUTE "30".

PAGE 11, TABLE VIII. END ITEM TESTS UNDER TEST

METHOD COLUMN, LINES 2 AND 3 DELETE "1600" AND

SUBSTITUTE "AATCC 20".

PAGE 12, PARAGRAPH 4.3.1.1. BONDING STRENGTH

PROCEDURE (INITIAL AND AFTER LAUNDERING/DRY

CLEANING). DELETE THE FIRST AND SECOND SENTENCES

IN THEIR ENTIRETY AND SUBSTITUTE: "CUT A 12 INCH

WARP BY 11 INCH FILLING SAMPLE FROM BOTH THE

OUTERSHELL AND FUSIBLE MATERIALS SPECIFIED FOR

CONTRACT USE (SEE 6.5)."

PAGE 15: AT THE END OF PARAGRAPH 6.1.1,ADD THE

FOLLOWING:

" E. STITCH REINFORCED NONWOVEN TYPE X1 OFFERS

HIGH DEGREE STRENGTH/STABILIZATION FOR TAPE AND

STAY APPLICATION FOR LARGE OR SMALL PART

FUSIBLES AND IS INTENDED TO PROVIDE VERTICAL

STABILITY AND ABRASION RESISTANCE."

PAGE 16, PARAGRAPH 6.5. BONDING STRENGTH DISPUTE

PROCEDURE. INSERT THE FOLLOWING BETWEEN THE

FIRST AND SECOND SENTENCES: "IN SOME CASES,

OUTERSHELL SAMPLES REPRESENTATIVE OF SEPARATE

PRODUCTION LOTS MAY BE USED TO DETERMINE IF

DIFFERENT FINISHES MAY AFFECT BONDING STRENGTH."

A-A-52094B Thread, Cotton dated 01 May 2019 No Additional Information (ref. T1481) A-A-52016A Cloth, Twill or Plain Weave, Polyester & Polyester Blend dated 19 Nov 2019 No Additional Information (ref. T1514) A-A-52108 Cloth, Interlining, Cotton & Synthetic or Synthetic is cancelled and replaced by A-A-59992 Cloth, Interlinings: Woven, Cotton and Synthetic dated 29 Nov 2018 (ref. T1524)

ADDITIONAL INFORMATION FOR A-A-55634A, 23 MARCH 2004:

SPECIAL NOTE!! ALL SLIDE FASTENERS USED ARE TO BE MEASURED FROM "STOP TO STOP".

RECOMMEND THAT THIS MEASUREMENT BE TAKEN RANDOMLY BEFORE SLIDE FASTENERS ARE SEWN TO

THE ITEMS, COVERALL, OR ANY ITEM REFERRED TO IN THE SOLICITATION. "THE QAR WILL

REJECT ANY SLIDE THAT IS NOT LAYING FLAT AFTER IT IS SEWN INTO/ONTO AN ITEM." SPECIAL INFO ON ITEMS THAT UTILIZE SLIDE FASTENERS IS GIVEN BY "ALL USING MILITARY PERSONNEL".

V-B-871F Button, Sewing Hole, and Button, Staple, (plastic) has been canceled and is superseded by A-A-59994 Button, Sewing Hole, and Button, Staple, (Plastic) dated 04 Dec 2018

No Information Follows

MIL-STD-129R w/CHANGE 2 - DEPARTMENT OF DEFENSE STANDARD PRACTICE MILITARY MARKING FOR

SHIPMENT AND STORAGE

DATED: 27 SEPTEMBER 2019

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE MATERIAL) SHALL

BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA TROOP SUPPORT C&T ITEMS,

REGARDLESS OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER TO BE LOADED FOR EACH SHIPMENT. THE WORDS

"PACKING LIST HERE" SHALL BE STENCILED, NOT HAND LETTERED, ON THE CONTAINER.

NOTE: UNIVERSAL PRODUCT CODE INFORMATION THE GOVERMENT ASSIGNED UNIVERSAL PRODUCT CODE

(UPC) MUST BE PLACED ON ALL SHIPPING CARTONS ON WHICH THE NSN APPEARS.

THE FOLLOWING DEFECTS APPLY FOR BARCODE LABELS/TAGS:

BAR CODE OMITTED OR NOT READABLE BY SCANNER

HUMAN-READABLE INTERPRETATION (HRI) OMITTED OR ILLEGIBLE

NOT VISIBLE ON FOLDED, PACKAGED ITEM CAUSES DAMAGE TO THE ITEM

MIL-STD-147E w/CHANGE 2

27 JUNE 2019

DEPARTMENT OF DEFENSE

STANDARD PRACTICE

PALLETIZED UNIT LOADS

ADDITIONAL INFORMATION FOR ANSI/ASQC Z1.4:

NOTE: THE MOST RECENT VERSION OF THIS DOCUMENT SHOULD BE USED.

APPLICATION FOR COPIES SHOULD BE ADDRESSED TO:

AMERICAN SOCIETY FOR QUALITY

600 NORTH PLANKINTON AVENUE

MILWAUKEE, WISCONSIN 53203

(Ref. T0795 - May 17, 2006)ACCEPTABILITY OF LOTS SHALL BE DETERMINED BY THE USE OF

"SAMPLING PROCEDURES AND TABLES FOR INSPECTION BY ATTRIBUTES",

ANSI/ASQC Z1.4

GENERAL INSPECTION LEVEL 2

AQL's FOR PURCHASE DESCRIPTION

END ITEM DIMENSIONAL 4.0

VISUAL 6.5