SPE1C1-20-R-0125 AMEND 002.pdf

AMENDMENT OF SOLICITATION/MODIFICATION OF CONTRACT

1. CONTRACT ID CODE PAGE F PAGES

2. AMENDMENT/MODIFICATION NO. 3. EFFECTIVE DATE 4. REQUISITION/PURCHASE REQ. NO. 5. PROJECT NO. (If applicable)

6. ISSUED BY CODE 7. ADMINISTERED BY (If other than Item 6) CODE

8. NAME AND ADDRESS OF CONTRACTOR No., street, county, State and ZIP Code) (X) 9A. AMENDMENT OF SOLICITATION NO.

9B. DATED (SEE ITEM 11)

10A. MODIFICATION OF CONTRACT/ORDER NO.

10B. DATED (SEE ITEM 13)

CODE FACILITY CODE

O

11. THIS ITEM ONLY APPLIES TO AMENDMENTS OF SOLICITATIONS

Offer must acknowledge receipt of this amendment prior to the hour and date specified in the solicitation or as amended, by one of the following methods:

The above numbered solicitation is amended as set forth in Item 14. The hour and date specified for receipt of Offers is extended, is not extended.

(a) By completing Items 8 and 15, and returning copies of the amendment; (b) By acknowledging receipt of this amendment on each copy of the offer submitted; or (c) By separate letter or telegram which includes a reference to the solicitation and amendment numbers. FAILURE OF YOUR ACKNOWLEDGMENT TO BE RECEIVED AT THE PLACE DESIGNATED FOR THE RECEIPT OF OFFERS PRIOR TO THE HOUR AND DATE SPECIFIED MAY RESULT IN REJECTION OF YOUR OFFER. If by virtue of this amendment you desire to change an offer already submitted, such change may be made by telegram or letter, provided each telegram or letter makes reference to the solicitation and this amendment, and is received prior to the opening hour and date specified.

12. Accounting and Appropriation Data (If required)

13. THIS ITEM APPLIES ONLY TO MODIFICATIONS OF CONTRACTS/ORDERS,

IT MODIFIES THE CONTRACT/ORDER NO. AS DESCRIBED IN ITEM 14.

(X) A. (Specify authority) THE CHANGES SET FORTH IN ITEM 14 ARE MADE IN

THE CONTRACT ORDER NO. IN ITEM 10A.

B. VE NUMBERED CONTRACT/ORDER IS MODIFIED TO REFLECT THE ADMINISTRATIVE CHANGES ( such as changes in paying office, appropriation date, etc .) SET FORTH IN ITEM 14, PURSUANT TO THE AUTHORITY OF FAR 43.103(b).

C. REEMENT IS ENTERED INTO

PURSUANT TO AUTHORITY OF:

D. HER (Specify type of modification and authority)

THIS CHANGE ORDER IS ISSUED PURSUANT TO:

THE ABO

THIS SUPPLEMENTAL AG

OT

E. IMPORTANT: Contractor is not, is required to sign this document and return copies to the issuing office.

14. DESCRIPTION OF AMENDMENT/MODIFICATION (Organized by UCF section headings, including solicitation/contract subject matter where feasible.)

Except as provided herein, all terms and conditions of the document referenced in Item 9A or 10A, as heretofore changed, remains unchanged and in full force and effect.

15A. NAME AND TITLE OF SIGNER (Type or print)

15B. CONTRACTOR/OFFEROR

(Signature of person authorized to sign)

15C. DATE SIGNED

16A. NAME AND TITLE OF SIGNER (Type or print)

16B. UNITED STATES OF AMERICA

(Signature of Contracting Officer)

16C. DATE SIGNED

BY

STANDARD FORM 30 (REV. 10-83)

Prescribed by GSA

FAR (48 CFR) 53.243

1. The following tech data is hereby incorporated into solicitation SPE1C1-20-R-0125 for the MDW Overcoat.

OVERCOAT, WITH REMOVABLE LINER, MAN’S MDW, WOOL, BLUE 150

shall be made in accordance with PD-319A dated 28 September 1972 STANDARD SAMPLE FOR CLOTH, ELASTIQUE, 100% WOOL, MIL-DTL-3738L, TYPE III, 16 OZ, BLUE 150, IS AVAILABLE ON ROLL NO. 2951, AND APPLICABLE FOR SHADE, FINISH AND COLORFASTNESS.

PATTERN DATE: 1 DECEMBER 2016

INTERIM CHANGES TO PD 319A:

PAGE 1, SPECIFICATION, FEDERAL: DELETE FEDERAL AND SUBSITUTE COMMERCIAL ITEM DESCRIPTIONS.

DELETE "V-B-871" AND SUBSTITUTE "A-A-59994”

DELETE "V-F-106" AND SUBSTITUTE "A-A-55634"

DELETE "V-T-276" AND SUBSTITUTE "A-A-52094"

DELETE "V-T-280" AND SUBSTITUTE "A-A-50198"

DELETE "V-T-295" AND SUBSTITUTE "A-A-59826"

DELETE ‘V-T-301”

DELETE "UU-P-268"

DELETE "CCC-C-438" AND SUBSTITUTE "A-A-50186"

DELETE "DDD-L-20" AND SUBSTITUTE "MIL-DTL-32075"

DELETE "DDD-T-86" AND SUBSTITUTE "A-A-52071"

DELETE "PPP-B-636"

PAGE 2, SPECIFICATIONS MILITARY:

DELETE "MIL-C-326" AND SUBSTITUTE "A-A-52106"

DELETE "MIL-C-368" AND SUBSTITUTE "A-A-52106"

DELETE "MIL-C-3191" AND SUBSTITUTE "A-A-50067"

DELETE "MIL-C-10176 CLOTH, WOOL, GABARDINE" AND

SUBSTITUTE "MIL-DTL-3738 CLOTH, WOOL, ELASTIQUE"

DELETE "MIL-C-15062" AND SUBSTITUTE "A-A-50067"

DELETE "MIL-C-16375" AND SUBSTITUTE "A-A-52097"

ADD “MIL-C-44296 CLOTH, FUSIBLES.

PAGE 2, UNDER "STANDARDS, FEDERAL", DELETE FED-STD-191,

TEXTILE TEST METHODS. DELETE FED-STD-751, STITCHES, SEAMS AND STITCHINGS.

PAGE 2, UNDER "STANDARDS, MILITARY ", DELETE MIL-STD-105,

DELETE MIL-STD-129

PAGE 2, AFTER MIL-C-44296, ADD NEW HEADING “DEPARTMENT OF DEFENSE STANDARDS”. UNDER “DEPARTMENT OF DEFENSE STANDARDS” ADD “MIL-STD-1391 – PROVISIONS FOR EVALUATING QUALITY OF OVERCOATS, MEN’S” (Copies of these documents are available online at https://quicksearch.dla.mil.)

PAGE 2 PARAGRAPH 2.2, DELETE “NATIONAL MOTOR FREIGHT TRAFFIC ASSOCIATION, INC, AGENT AND ALL

REFRENCES”

PAGE 2 PARAGRAPH 2.2, ADD THE FOLLOWING:

AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS (AATCC)

AATCC EP1 - Evaluation Procedure for Gray Scale for Color Change AATCC EP2 - Evaluation Procedure for Gray Scale for Staining https://quicksearch.dla.mil/

AATCC EP8 - Evaluation Procedure for AATCC 9-Step Chromatic Transference Scale AATCC TM132 - Test Method for Colorfastness to Drycleaning

(Copies of these documents are available online at https://www.aatcc.org.)

AMERICAN SOCIETY FOR QUALITY (ASQ)

ASQ/ANSI Z1.4 - Sampling Procedures and Tables for Inspection by Attributes

(Copies of this document are available online at https://asq.org.)

ASTM INTERNATIONAL

ASTM D276 - Standard Test Method for Identification of Fibers in Textiles ASTM D1776 - Standard Practice for Conditioning and Testing Textiles ASTM D3775 - Standard Test method for Warp (End) and Filling (Pick) Count of Woven Fabrics ASTM D3776/3776M - Standard Test Method for Mass Per Unit Area (Weight) of Fabric ASTM D5034 - Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test) ASTM D6193 - Standard Practice for Stitches and Seams

(Copies of these documents are available for purchase online at http://www.astm.org.)

INFORMA HEALTHCARE

Repeat Insult Patch Test - Modified Draize Procedure – Principles and Methods of Toxicology, A Wallace Hayes (editor).

(Copies of this document are available online at https://www.crcpress.com.)

SDL ATLAS

Part Number 402985 – Slub/Knot Replica Set (Replica set is available for purchase from SDL Atlas Customer Service, 1-803-329-2110.)

PAGE 3, PARA. 3.2.1, LINE 2, DELETE "GABARDINE"

AND SUBSTITUTE "ELASTIQUE". ALSO DELETE "TYPE I, CLASS 4 OF MIL-DTL-10176" AND

SUBSTITUTE "TYPE III- 16 OUNCE OF MIL-DTL-3738".

PAGE 3, PARA. 3.2.2, DELETE IN ITS ENTIRETY AND SUBSTITUTE THE FOLLOWING:

"3.2.2 BASIC MATERIAL FOR LINERS. THE BASIC MATERIAL FOR THE REMOVABLE LINER

SHALL BE A 12-OUNCE WOOL FLANNEL CONFORMING TO A-A-50067. THE COLOR SHALL BE BLUE 293 PAGE 3, PARA. 3.2.3 LINING. DELETE IN ITS ENTIRETY AND SUBSTITUTE "3.2.3 LINING. THE BASIC MATERIAL FOR LINING THE OVERCOAT FROM THE SHOULDERS TO THE WAIST, FOR LINING THE REMOVABLE LINER FROM THE TOP TO THE MID-BACK, ZIPPER BELLOWS, AND FOR BINDING SEAMS AND EDGES SHALL BE 100% POLYESTER, CONFORMING TO A-A-52106. AS AN ALTERNATE, ACETATE MAY BE USED. THE COLOR SHALL BE A GOOD MATCH TO

THE BASIC MATERIAL.

AT THE OPTION OF THE SUPPLIER, THE LINING MATERIAL SHALL BE USED FOR HANGER

LOOPS AND BUTTON LOOPS ON THE LINER SLEEVES (SEE 3.2.12 AND OPER. 1.J.)."

PAGE 3, PARA 3.2.5, LINE 3, DELETE "TYPE I,

CLASS 2 OF CCC-C-438" AND SUBSTITUTE "TYPE I OF A-A-50186".

https://asq.org/

PAGE 3, PARA 3.2.6, DELETE IN ITS ENTIRETY AND SUBSTITUTE:

UNDERCOLLAR MATERIAL. THE MATERIAL FOR THE UNDERCOLLAR SHALL BE A WOOL FLANNEL

CONFORMING TO A-A-50067, EXCEPT THE COLORFASTNESS REQUIREMENTS FOR PERSPIRATION

AND CROCKING SHALL NOT APPLY. THE COLOR SHALL BE DARK BLUE 237 OR BLACK 449.

PAGE 3, PARA 3.2.7 LINE 2, DELETE "MIL-C-16375" AND SUBSTITUTE "A-A-52097"

PAGE 4, PARA 3.2.8, LINE 3, DELETE "TYPE I OR II OF MIL-C-43718" AND SUBSTITUTE

"CLASS 1, 2, OR 3 OF A-A-52106"

PAGE 4, PARA 3.2.9, LINE 6, DELETE "TYPE I OR II OF MIL-C-43718" AND SUBSTITUTE

"CLASS 1, 2, OR 3 OF A-A-52106"

PAGE 4 PARA 3.2.10 : DELETE IN ITS ENTIRETY AND SUBSTITUTE:

SHOULDER PADS AND SLEEVE HEADS. THE SHOULDER PADS SHALL CONFORM TO TYPE I, CLASS 1 AND THE

SLEEVE HEADS SHALL CONFORM TO TYPE IV OF MIL-P-15064

PAGE 4, PARA 3.2.11, LINE 4 DELETE "DDD-T-86" AND SUBSTITUTE "A-A-52071"

PAGE 4 PARA 3.2.13 : DELETE IN ITS ENTIRETY AND SUBSTITUTE SLEEVE ORNAMENTATION.

THE SLEEVE ORNAMENTATION BRAID SHALL BE A 1/8-INCH WIDE NYLON SOUTACHE BRAID,

CONFORMING TO TYPE I, CLASS 1 OF MIL-B-13466.

THE BRAID SHALL MATCH SHADE GOLDENLITE; CABLE 67107

PAGE 5, PARA 3.2.14.1, LINE 1, DELETE "IA3" AND

SUBSTITUTE "I". LINE 2, DELETE "V-T-276" AND

SUBSTITUTE "A-A-52094". LINE 4, DELETE "IA3, OR

IB3," AND SUBSTITUTE "I, OR II". LINE 6, DELETE

"V-T-276" AND SUBSTITUTE "A-A-52094".

PAGE 5, PARA 3.2.14.2, DELETE "WAXED MONOCORD SPECIAL

NO. 5" AND SUBSTITUTE "TYPE III, CLASS 1, GOVERNMENT NUMBER SIZE 5 OF A-A-59826"

DELETE "V-T-295" AND SUBSTITUTE "A-A-59826"

PAGE 5, PARA 3.2.14.3, SILK THREAD DELETE PARAGRPH IN ITS ENTIRETY AND ALL ASSOCIATED

REFERENCES TO SILK.

PAGE 5, PARA 3.2.14.5, THE GIMP FOR REINFORCING THE BUTTONHOLES SHALL BE COTTON, SOFT FINISH OR GLAZED FINISH, SIZE 8 (TEX 210), CONFORMING TO TYPE I OR II OF A-A-50198. THE COLOR OF THE GIMP THREAD SHALL MATCH THE STANDARD SAMPLE FOR BLACK SHADE AA. THE DYED GIMP SHALL SHOW FASTNESS TO

DRYCLEANING EQUAL TO BETTER THAN THE STANDARD SAMPLE.

PAGE 5, PARA 3.2.14.6, DELETE IN ITS ENTIRETY AND SUBSTITUTE THE FOLLOWING: " THE COLOR OF THE COTTON, OR NYLON THREADS SHALL MATCH THE STANDARD SAMPLE FOR BLACK AA (C.A. 66043), EXCEPT THE THREAD FOR STITCHING THE SOUTACHE BRAID TO THE SLEEVE SHALL MATCH THE GOLDENLITE SHADE (SEE 3.6.2). THE THREAD FOR TACKING THE ARMHOLES AND ATTACHING THE SLEEVE-HEAD AND PADS SHALL BE WHITE. ALL DYED THREADS SHALL SHOW FASTNESS TO DRYCLEANING AND LIGHT EQUAL OR BETTER THAN THE STANDARD SAMPLE.

PAGE 6, PARA 3.2.15, THE ZIPPER FOR ATTACHING THE LINERS SHALL BE TYPE III,

STYLE 1, SIZE 3, CONFORMING TO A-A-55634. THE ZIPPER SHALL HAVE A SHORT PULL TAB

AND INDIVIDUAL ELEMENT BRASS CHAIN. THE LENGTH FOR SIZES EXTRA-SHORT AND SHORT

SHALL BE 74-INCHES AND FOR SIZES REGULAR, LONG AND EXTRA-LONG SHALL BE 80-INCHES.

THE COLOR FOR THE TAPE SHALL BE A GOOD MATCH TO THE BASIC MATERIAL. THE TAPES SHALL

MEET THE COLORFASTNESS REQUIREMENTS AS SPECIFIED IN 3.7.11.

PAGE 6, PARAGRAPH 3.2.16, DELETE "BLACK SHADE BT, CABLE NO. 62001" AND

SUBSTITUTE "A GOOD MATCH TO THE BASIC MATERIAL OF THE OVERCOAT"

PAGE 6, PARAGRAPH 3.2.17.1: DELETE IN ITS ENTIRETY AND SUBSTITUTE:

FRONT CLOSURE. THE BUTTONS FOR THE FRONT CLOSURE SHALL BE 24 KARAT GOLD PLATED METAL, 45-LIGNE

WITH SHORT SHANK, AND SHALL CONFORM TO TYPE I, STYLE 2, CLASS A OF MIL-B-3461.

PAGE 6, PARAGRAPH 3.2.17.2: DELETE IN ITS ENTIRETY AND SUBSTITUTE:

SHOULDER LOOP. THE BUTTONS FOR THE SHOULDER LOOP SHALL BE 24 KARAT GOLD PLATED METAL, 25-LIGNE

WITH SHORT SHANK AND CONFORM TO TYPE I, STYLE 2, CLASS B OF MIL-B-3461.

PAGE 6, PARAGRAPH 3.2.17.3: ANCHOR BUTTON. THE ANCHOR BUTTON SHALL BE A 45-LIGNE, WITH GLOSSY FINISH AND CONFORM TO TYPE I, CLASS 1, STYLE 20 OR 24 OF A-A-59994. THE COLOR SHALL BE BLACK.

PAGE 6, PARAGRAPH 3.2.18, DELETE IN ITS ENTIRETY AND SUBSTITUTE:

EACH OVERCOAT SHALL HAVE A SIZE LABEL, IDENTIFICATION LABEL, CARE INSTRUCTION, AND A BARCODE LABEL/TAG. THE SIZE AND IDENTIFICATION LABEL MAY BE COMBINED. EACH LINER SHALL HAVE A SIZE, IDENTIFICATION AND CARE INSTRUCTION LABEL. THE SIZE, IDENTIFICATION AND CARE INSTRUCTION LABEL MAY BE

COMBINED.

PAGE 6, PARAGRAPH 3.2.18.1, DELETE IN ITS ENTIRETY AND SUBSTITUTE: COMBINATION SIZE/IDENTIFICATION LABEL.

THE COMBINATION SIZE/IDENTIFICATION LABEL SHALL CONFORM TO TYPE VI, CLASS 14 OF MIL-DTL-32075. THE COMBINATION LABEL SHALL BE SEWN TO THE CENTER BACK OF THE LINER (SEE TABLE VIII, OPERATION 5.A).

PAGE 6, PARAGRAPH 3.2.18.2, DELETE IN ITS ENTIRETY.

PAGE 6, PARAGRAPH 3.2.18.3, CARE INSTRUCTION LABEL. THE CARE INSTRUCTION LABEL SHALL CONFORM TO TYPE VI, CLASS 3 OF MIL-DTL-32075. THE LABEL SHALL BE POSITIONED ON THE HANGING POCKET AS SPECIFIED IN TABLE VIII, OPERATION 22.A. THE LETTERS FOR THE CAPTION SHALL BE NO LESS THAN 3/16- INCH IN HEIGHT, AND ALL OTHER LETTERING SHALL BE NO LESS THAN 1/8-INCH IN HEIGHT. THE CONTENTS

OF THE LABEL SHALL BE AS FOLLOWS:

OVERCOAT, MAN’S, WOOL, BLUE, WITH REMOVABLE LINER

1. DRY CLEAN ONLY.

2. Use a damp cloth for outside pressing.

3. Remove wrinkles or gloss marks at edges and seams with a steam iron or an iron and damp press cloth. Press/iron temperature with steam shall be 325 (±5)oF on wool setting with steam.

4. Roll press (without creasing) sleeves and lapels.

DO NOT REMOVE THIS LABEL

PAGE 6, PARAGRAPH 3.2.18.4, DELETE IN ITS ENTIRETY AND SUBSTITUTE: BAR CODE HANG TAG. EACH OVERCOAT SHALL HAVE A BARCODE LABEL/HANGTAG CONFORMING TO TYPE VIII, CLASS 17 OF MIL-DTL-32075. THE BAR CODING ELEMENT SHALL BE A 13 DIGIT NATIONAL STOCK NUMBER (NSN). THERE SHALL BE A 12 DIGIT UNIVERSAL PRODUCT CODE (UPC) NUMBER ASSIGNED FOR ALL NSNS BY THE CONTRACTING ACTIVITY. THE INITIALS “UPC” MUST APPEAR BENEATH THE CODE. THE BARCODE FOR NSN AND UPC TYPE SHALL BE A MEDIUM TO HIGH DENSITY AND SHALL BE

LOCATED SO THAT IT IS COMPLETELY VISIBLE ON THE OVERCOAT WHEN IT IS FOLDED AND/OR PACKAGED AS

SPECIFIED AND SO IT CAUSES NO DAMAGE TO THE OVERCOAT.

PAGE 7, TABLE I, LINE 1, DELETE "GABARDINE" AND SUBSTITUTE "ELASTIQUE"

PAGE 8, TABLE I, LINES 5 AND 7 DELETE "RAYON CLOTH" AND SUBSTITUTE "POLYESTER CLOTH OR ACETATE”

PAGE 9, PARA 3.5.1, LINE 2, DELETE "FED-STD-751" AND SUBSTITUTE "ASTM-D6193"

PAGE 25, OPER. 19.B, DELETE IN ITS ENTIRETY AND SUBSTITUTE:

"19.B. POSITION BRAID (SEE 3.2.13) ON SLEEVE SO THAT ON THE FINISHED OVERCOAT, IT WILL BE 3 INCHES FROM BOTTOM OF SLEEVE AT UNDERARM SEAM, STITCH SOUTACHE BRAID TO SLEEVE WITH THE ROW OF STITCHING IN CENTER OF BRAID. CONTINUED ACROSS TOP SLEEVE AND UNDERSLEEVE BACK TO THE UNDERARM SEAM. A TOLERANCE OF 1/8 INCH SHALL BE ACCEPTABLE ON THE ABOVE DIMENSION. THE BRAID

SHALL NOT BE STAGGERED MORE THAN 1/16 INCH AT UNDERARM SEAM."

NOTE; SIZE 40 SHOULD BE 23 INCHES AND NOT 24 INCHES FOR 1/2 BREAST MEASUREMENT. IT IS TO BE NOTED THAT 1/2 BREAST MEASUREMENT IN TABLE III OF PURCHASE DESCRIPTION 319A SHOULD ALL BE ONE

INCH LESS THAN SHOWN ON PAGE 46 (EXCLUDING THE TOLERANCE).

PAGE 48, PARA 4.2, DELETE "MIL-STD-105" AND SUBSTITUTE "MIL-STD-191"

PAGE 48, PARA 4.2.1, DELETE "FED-STD-191" AND SUBSTITUTE "ASTM AND AATCC"

PAGE 49, TABLE V, UNDER TEST METHOD DELETE"1200" AND SUBSTITUTE "ASTM D-276";

DELETE "5041" AND SUBSTITUTE "ASTM D-3776";

DELETE "5050" AND SUBSTITUTE "ASTM D-3775";

DELETE "5100" AND SUBSTITUTE "ASTM D-5034";

DELETE "2020" AND SUBSTITUTE "2/";

DELETE "5622" AND SUBSTITUTE "AATCC 132"

PAGE 49, TABLE V, ADD NEW FOOTNOTE:

"2/ PRESENCE OF LABILE SULFUR:

IN THE DETERMINATION OF PRESENCE OF LABILE

SULFUR IN TEXTILE MATERIALS WITH LEAD ACETATE,

TWO 1/50 +/- 0.01 GRAM SAMPLES FROM EACH MATERIAL SUBMITTED FOR EVALUATION SHALL BE TESTED. EACH OF THE TWO SAMPLES SHALL BE CUT INTO VERY SMALL PIECES AND PLACED INTO

SEPARATE TEST TUBES. THE SAMPLES SHALL BE

SUBMERSED IN A STANNOUS CHLORIDE SOLUTION THAT

CONTAINS 100 GRAMS OF STANNOUS CHLORIDE CRYSTALS

ACS IN 100 MILLILITERS OF HYDROCHLORIC ACID ACS

(35 PERCENT CONCENTRATION) AND 50 MILLILITERS OF

DISTILLED WATER. A FILTER PAPER WET OUT WITH A

5.0 PERCENT LEAD ACETATE SOLUTION SHALL BE

PLACED OVER TOP OF THE TEST TUBE. THE LEAD

ACETATE SOLUTION CONTAINS 5.0 GRAMS OF LEAD

ACETATE CP REAGENT GRADE AND ENOUGH DISTILLED

WATER TO MAKE UP A 100 MILLILIETER SOLUTION;

IF THE SOLUTION IS NOT CLEAR, ADD A FEW DROPS

(ONE AT A TIME) OF GLACIAL ACETATE ACID UNTIL THE

SOLUTION IS CLEAR. THE TEST TUBE CONTAINING THE

TEXTILE SAMPLE, STANNOUS CHLORIDE AND WET FILTER

PAPER SHALL BE HEATED OVER A LOW FLAME UNTIL THE

SOLUTION IS BOILING. THE SOLUTION SHOULD NOT BE

HEATED FOR MORE THAN 15 SECONDS. A BROWN TO BLACK

STAIN ON THE FILTER PAPER SHOULD BE EVALUATED AS

FOLLOWS:

FREE- THE FILTER PAPER SHOWS NO DISCOLORATION OR STAINING OF ANY KIND.

SLIGHT- THE FILTER PAPER SHOWS A LIGHT TAN TO LIGHT BROWN DISCOLORATION STAIN.

MODERATE- THE FILTER PAPER SHOWS A DARK BROWN DISCOLORATION STAIN

SEVERE- THE FILTER PAPER SHOWS A BLACK COLOR STAIN

PAGE 70, PARA. 4.2.3.5, DELETE AQLS AS FOLLOWS:

CLASSIFICATION OF DEFECTS

(FOR VISUAL EXAMINATION): DELETE SUBSTITUTE

MAJOR 2.5 1.5

MAJOR & MINOR A COMBINED 10.0 6.5

MAJOR, MINOR A, MINOR B 25.0 15.0

FOR DIMENSIONAL EXAMINATION 4.0 2.5

NOTE: BAR CODE REQUIRED LABEL/TAG. EACH ITEM SHALL BE INDIVIDUALLY

BAR CODED WITH A TYPE VIII, CLASS 17, LABEL/TAG

OF MIL-DTL-32075 THE LABEL/TAG SHALL BE LOCATED SO THAT IT IS COMPLETELY VISIBLE ON THE ITEM WHEN

FOLDED AND/OR PACKAGED AS SPECIFIED AND SHALL CAUSE NO DAMAGE TO THE ITEM."

(Ref. W1835)

ADDITIONAL INFORMATION FOR V-B-871: NO ADDITIONAL INFORMATION FOLLOWS.

ADDITIONAL INFORMATION FOR A-A-55634A, 23 MARCH 2004:

SPECIAL NOTE!! ALL SLIDE FASTENERS USED ARE TO BE MEASURED FROM "STOP TO STOP". RECOMMEND THAT THIS MEASUREMENT BE TAKEN RANDOMLY BEFORE SLIDE FASTENERS ARE SEWN TO THE ITEMS, COVERALL, OR ANY ITEM REFERRED TO IN THE SOLICITATION. "THE QAR WILL REJECT ANY SLIDE THAT IS NOT LAYING FLAT AFTER IT IS SEWN INTO/ONTO AN ITEM." SPECIAL INFO ON ITEMS THAT UTILIZE SLIDE FASTENERS IS GIVEN BY "ALL USING

MILITARY PERSONNEL".

ADDITIONAL INFORMATION FOR A-A-52094A:

NO ADDITIONAL INFORMATION

(ref. T1481)

ADDITIONAL INFORMATION FOR A-A-50067:

PAGE 1 PARA 2.2, LINE 5, AFTER " SECTION 16"

DELETE "THE CLOTH SHALL HAVE A MAXIMUM SHRINKAGE

RATE OF 2.0 IN THE WARP AND FILLING DIRECTION."

AND SUBSTITUTE " THE CLOTH SHALL HAVE A MAXIMUM

SHRINKAGE RATE OF 4.0 IN BOTH THE WARP AND

FILLING DIRECTIONS."

(Ref. T0402)

ADDITIONAL INFORMATION FOR A-A-50198:

THE GIMP THREAD SHALL BE MADE IN ACCORDANCE

WITH A-A-50198A, DATED 6/21/00

NO ADDITIONAL INFORMATION FOLLOWS:

CHANGES TO V-T-295E:

THREAD, NYLON; V-T-295 DATED AUGUST 1, 1985 IS HEREBY CANCELLED; FUTURE ACQUISITONS SHOULD REFER TO

THREAD, NYLON, A-A-59826 DATED 03 MARCH 2009 AS A REPLACEMENT.

ADDITIONAL INFORMATION FOR A-A-50196:

(NO CURRENT CHANGES TO A-A-50196B)

ADDITIONAL INFO FOR UU-P-268: UU-P-268 IS CANCELLED.

USE A-A-203C DATED 1/3/96 AND A-A-1894A DATED 5/27/93.

(ref. T0688 - 9/11/06)

ADDITIONAL INFORMATION: INTERIM CHANGES TO A-A-50186:

PAGE 1:

PARA. 1.1 TYPES, NEXT TO TYPE V NON-WOVEN ADD

"(MEDIUM WEIGHT)", UNDER TYPE V ADD "TYPE VI

NON-WOVEN (LIGHT WEIGHT)".

PARAGRAPH 2.1, LINE 5. GENERAL.: DELETE

"SATURATION BONDED WITH ACRYLIC TYPE BINDER"

AND SUBSTITUTE "EITHER WET-LAID, SATURATION BONDED OR THERMAL BONDED".

PAGE 2:

TABLE 1. PHYSICAL REQUIREMENTS (WOVEN) UNDER TEST

METHOD COLUMN, LINE 3 DELETE "1600" AND SUBSTITUTE

"AATCC 20 3/".

TABLE I. PHYSICAL REQUIREMENTS (WOVEN) AT BOTTOM OF

PAGE UNDER FOOTNOTE 2/ ADD THE FOLLOWING: "3/ AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND

COLORISTS

TEST METHOD."

PAGE 3, TABLE II, PHYSICAL REQUIREMENTS (NONWOVEN) UNDER

TYPE V, AND VI, ACROSS "CONSTRUCTION": DELETE "WET-LAID"

AND "WET-LAID OR SATURATE, THERMAL BONDED" AND SUBSTITUTE

"SEE 2.1" FOR BOTH TYPES.

TABLE II, UNDER TYPE VI: ADD UNDER EACH CHARACTERISTIC:

"1.5, 12, 8, 2.5, 2.5, WET-LAID OR SATURATE THERMAL BONDED" RESPECTIVELY.

PAGE 3, PARA. 3.2 FINISH. LINE 1 DELETE "AN APPROVED" AND SUBSTITUTE " A COMMERCIALLY ACCEPTED".

PAGE 5: ADD THE FOLLOWING: "5.7 SUPER SESSION DATA.

THE TYPES OF CLOTH COVERED BY THIS COMMERCIAL ITEM

DESCRIPTION REPLACE TYPES COVERED BY CCC-C-438 AS FOLLOWS:

A-A-50186 CCC-C-438

TYPE I TYPE I, CLASSES 1 AND 2

TYPE II TYPE II, CLASS 1

TYPE III TYPE III, CLASS 1

TYPE IV TYPE III, CLASS 2

TYPE V TYPE IV, CLASS 1

TYPE VI TYPE IV, CLASS 2"

(ref. T1034 - May 19, 2006)

MIL-DTL-32075: LABEL FOR CLOTHING, EQUIPAGE,AND TENTAGE, GENERAL USE REPLACES DDD-L-20 (Ref. T0451 - June 19, 2007)

INTERIM SPECIFICATION CHANGES TO MIL-DTL-32075:

PAGE 4, PARA. 3.3.5, AFTER "TYPE III OR IV, CLASS 4 OF" DELETE "DDD-L-20" AND REPLACE "MIL-DTL-32075,".

PAGE 6, TABLE I, "PHYSICAL REQUIREMENTS OF THE TYPE VI FINISHED LABEL." UNDER "TEARING

STRENGTH" DELETE: "(LB.) MINIMUM" AND SUBSTITUTE: "(GNS) MINIMUM."

PAGE 12, PARA 3.3.2.17, AFTER "NSN" ADD "AND THE UNIVERSAL PRODUCT CODE (UPC)

SUPPLIED BY THE GOVERNMENT, FOR ALL NSNs."

COMMERCIAL ITEM DESCRIPTION A-A-52071

DATED 25 APRIL 1990 HAS BEEN AUTHORIZED FOR USE IN PLACE 0F DDD-T-86H.

"THE REQUIREMENT FOR THE HERRINGBONE TAPE IS TYPE I, 3/16 INCH WIDTH AND 58 PICKS PER INCH FROM TABLE

I. PHYSICAL REQUIREMENTS."

ADDITIONAL INFORMATION FOR A-A-52071:

TAPE, TEXTILE, COTTON, FOR GENERAL USE.

ADDITIONAL INFORMATION FOR PPP-B-636:

FEDERAL SPECIFICATION PPP-B-636 DATED JULY 12, 1981, INCLUDING INTERIM FEDERAL SPECIFICATION PPP-B-636L DATED JANUARY 1, 1991, IS HEREBY CANCELLED, AND REPLACED WITH ASTM-D-5118, STANDARD PRACTICE FOR FABRICATION OF FIBERBOARD SHIPPING BOXES, AND ASTM-D-1974, STANDARD PRACTICE FOR METHOD OF

CLOSING, SEALING AND REINFORCING FIBERBOARD SHIPPING CONTAINERS.

ADDITIONAL INFORMATION FOR MIL-B-371:

PAGE 2, AT THE TOP OF THE PAGE AFTER "CLASS 3" ADD "AND 4". DELETE "CLASS 4 -WATER AND MILDEW-

RESISTANT FINISH 2, 2' METHYLENE BIS (4-CHLOROPHENOL)".

PAGE 3, PARAGRAPH 2.2 OTHER PUBLICATIONS. ADD THE FOLLOWING BELOW "APPLICATION FOR COPIES SHOULD BE ADDRESSED TO: ASTM INTERNATIONAL, 100 BARR HARBOR DRIVE, WEST CONSHOHOCKEN, PA. 19428"

"AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS (AATCC) AATCC 20 - FIBER ANALYSIS: QUALITATIVE (APPLICATIONS FOR COPIES SHOULD BE ADDRESSED TO: AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND

COLORISTS (AATCC), P.O. BOX 12215, TRIANGLE PARK, NC 27709-2215)"

PAGE 4, PARA. 3.3.3, DELETE IN ITS ENTIRETY AND SUBSTITUTE THE FOLLOWING: "3.3.3 POLYPROPYLENE YARN (AS AN ALTERNATIVE FOR TYPES III AND VII BRAID). THE YARN SHALL BE TEXTURED POLYPROPYLENE OF SUITABLE DENIER TO MEET THE REQUIREMENTS OF THIS DOCUMENT. POLYPROPYLENE BRAID IS APPLICABLE ONLY TO THE

ITEMS LISTED IN PARAGRAPH 6.7."

AFTER PARA. 3.3.4: ADD THE FOLLOWING NEW PARA: "3.3.5. 100% TEXTURED POLYESTER(AS AN ALTERNATIVE FOR TYPES I, II, IV, AND VI).THE YARN SHALL BE TEXTURED POLYESTER OF A SUITABLE DENIER TO MEET THE

REQUIREMENTS OF THIS DOCUMENT."

PAGE 5, PARA. 3.5.3 AFTER "CLASS 3" ADD "CLASS 4." AFTER "THE CLASS 3" ADD "AND 4".

PARA. 3.5.4, DELETE IN ITS ENTIRETY.

PAGE 8, ADD THE FOLLOWING TABLE IIA:

"TABLE IIA PHYSICAL REQUIREMENTS FOR POLYESTER BRAID

TYPE DIAMETER WEIGHT PER NUMBER OF ENDS PER

(INCHES) 144 YARDS CARRIERS CARRIER

(OUNCES)

MIN.

II 5/32+/-1/32 28.0 8 1

VII 11/32+/-1/32 25.0 44 1

NUMBER YARN PLY PICKS BREAKING

OF ENDS BRAID CORE PER INCH STRENGTH

IN CORE MIN. (LBS.) MIN.

1/ 8 2 3 10 140

- - - 22 200

1/ UNDYED COTTON CORE YARNS."

PAGE 10, PARA. 4.4.2.1 YARD-BY-YARD EXAMINATION, LINE 9, DELETE "1.5" AND SUBSTITUTE "1.0"

PAGE 13, TABLE V. END ITEM TESTS UNDER REFERENCED TEST METHOD COLUMN, LINES 4 AND 5 DELETE "1600" AND

SUBSTITUTE "AATCC 20"

(ref. T0821 - May 18, 2006)

ADDITIONAL INFORMATION FOR MIL-B-1962:

MIL-B-1962 IS CANCELLED WITHOUT REPLACEMENT.

(Ref. T0832)

ADDITIONAL INFORMATION FOR MIL-C-3191:

MIL-C-3191 IS CANCELLED WITHOUT REPLACEMENT.

(Ref. T0935)

ADDITIONAL INFORMATION FOR MIL-C-3738:

WITH THE FOLLOWING INTERIM CHANGES TO MIL-C-3738:

NOTE: REDUCED AQL'S APPLY AS FOLLOWS:

PAGE 2, 2.1.2, DELETE LINES 4 THRU 7 AND

SUBSTITUTE:

"U.S. DEPARTMENT OF AGRICULTURE

METHODS OF TEST FOR GRADES OF WOOL TOP

(APPLICATION FOR TEST COPIES SHOULD BE ADDRESSED

TO THE U.S. DEPARTMENT OF AGRICULTURE, AGRI-

CULTURAL MARKETING SERVICE, WASHINGTON, DC

20402.)"

PAGE 6, AFTER 4.4.2, ADD THE FOLLOWING:

"4.4.2.1, WOOL. THE WOOL SHALL BE EXAMINED FOR

GRADE (SEE 3.3.1) IN THE UNDYED TOP FORM BY

COMPARISON WITH THE APPLICABLE U.S. STANDARD

(SEE 2.1.2). IN THE EVENT OF A DISPUTE, THE WOOL

GRADE SHALL BE DETERMINED BY THE WIDTH METHOD

(WEDGE). THE SAMPLE UNIT SHALL BE 1 YARD OF TOP,

PRIOR TO DYEING. THE SAMPLE SIZE (NUMBER OF

SAMPLE UNITS) SHALL BE AS LISTED BELOW. THE LOT

SIZE SHALL BE EXPRESSED IN UNITS OF ONE POUND.

THE RESULTS FROM EACH SAMPLE UNIT SHALL BE

REPORTED SEPARATELY. THE LOT SHALL BE UNACCEPT-

ABLE IF A SINGLE SAMPLE UNIT FAILS TO MEET THE

REQUIRED GRADE.

LOT SIZE (POUNDS) SAMPLE SIZE

800 OR LESS 2

801 UP TO AND INCLUDING

22,000 3

22,001 AND OVER 5

PARA. 4.4.3.1 POINT COUNT EXAMINATION, SECOND

LINE, DELETE "10" AND SUBSTITUTE "7". AT END OF

PARAGRAPH, ADD THE FOLLOWING: "EXCEPT THAT

BOWED OR SKEWED FILLING YARNS SHALL NOT BE

SCORED."

PAGE 7, TABLE II, LINE 1, DELETE THE FOLLOWING:

"WOOL GRADE 3.3.1 ASTM D 2130 1/

UNDER TABLE II, DELETE "1/" IN ITS ENTIRETY.

PAGE 8, DELETE PARAS. 4.5 AND 4.5.1.

PAGE 11, PARA. 6.7, DELETE IN ITS ENTIRETY.

CERTIFICATE OF CONFORMANCE IS APPLICABLE FOR

THE GRADING OF WOOL IN TOP FORM.

ADDITIONAL INFORMATION FOR MIL-B-13466:

SHADE SHALL BE IN ACCORDANCE WITH ROLL NUMBER 3771

INTERIM SPECIFICATION CHANGES TO MIL-B-13466E:

PAGE 1, PARAGRAPH 1.2, CLASSIFICATION. UNDER "TYPE II- LACE, WOVEN CLASS 1 - PLAIN WITH

VELLUM STRIPE" ADD "STYLE C - 3/4 INCH STYLE D - 1 INCH"

PAGE 7, PARAGRAPH 3.5.3, TYPE I, CLASS 3 LINE 1, AFTER "THE 1/2 INCH BRAID" ADD "OR LACE".

PAGE 8, PARAGRAPH 3.5.3.1, BRAID, 1/2 INCH.

- LINE 1, AFTER "THE BRAID" ADD "OR LACE".

-LINE 5, ADD AFTER "TABLE III" "OR TABLE IV"

PAGE 8 PARAGRAPH 3.5.5 LINE 4 AFTER (SEE 3.3.2).

ADD "AS AN ALTERNATE POLYESTER MAY BE USED FOR THE FILLING YARN.

PAGE 11, TABLE IV: DELETE IN ITS ENTIRETY AND SUBSTITUTE THE FOLLOWING NEW TABLE IV:

"TABLE IV. PHYSICAL REQUIREMENTS FOR TYPE II WOVEN LACE

Class/Style/ Width (Tolerance + 1/32,-0)inches/Total No. of ends (warp)min/ Weight per lin. Yard (ozs)/

1 A 1/2 128 0.20 1 B 1-1/2 300 0.50 1 C 3/4 170 0.24 1 D 1 230 0.30

2 A 3/4 172 1/ 0.24 2 B 1-3/4 456 2/ 0.60

Picks per inch (fill), min/ Number of Vellum 230 3/ 2 230 2 230 2 230 2 230 - 230 -

WEAVE PATTERN/ RIBS PER INCH (CENTER STRIPE)

1 A FILLING EFFECT -

. (SEE 3.6.1)

1 B FILLING EFFECT -

1 C FILLING EFFECT -

1 D FILLING EFFECT -

2 A FILLING EFFECT 3/ 22

2 B FILLING EFFECT 4/ 22

WARP BREAKING STRENGTH (POUNDS) MIN

1/ ARRANGED 51 LEFT; 70 CENTER STRIPE; 51 RIGHT

2/ ARRANGED 128 LEFT; 200 CENTER STRIPE; 128 RIGHT

3/ TWO PICKS PER SHED, WHEN USING NEEDLE OR SHUTTLELESS LOOM

4/ 1/4 INCH GOLD COLOR, 1/4 INCH BRANCH OF SERVICE COLOR, 1/4 INCH GOLD COLOR

5/ 1/2 INCH GOLD COLOR, 3/4 INCH BRANCH OF SERVICE COLOR

(SEE 3.5.5.1), 1/2 INCH GOLD COLOR"

PAGE 12 , ADD NEW PARAGRAPH:

"3.6.1.1 VELLUMS. THE VELLUMS ON THE LACE SHALL BE SYMMETRICAL WITH BOTH SETS OF VELLUMS THE

SAME WIDTH AND EQUIDISTANCE FROM THE EDGES OF THE LACE."

PAGE 12, ADD THE FOLLOWING NEW PARAGRAPHS:

"3.6.3 FINISH. THE TYPE II, CLASS 1 LACE SHALL BE PRESHRUNK. THE LACE MAY HAVE A FINISH TREATMENT APPLIED TO ASSIST IN STABILIZING THE LACE AND PREVENTING WAVINESS AND PUCKERING. ANY FINISH SHALL

MEET THE TOXICITY REQUIREMENTS IN 3.10.

3.6.4 DIMENSIONAL CHANGE TO DRY-CLEANING. THE TYPE II, CLASS 1 LACE SHALL NOT SHRINK OR ELONGATE MORE THAN 1 PERCENT IN THE WARP DIRECTION AFTER 1 DRY-CLEANING WHEN TESTED AS SPECIFIED IN 4.4.3.

3.6.4.1 DIMENSIONAL CHANGE TO LAUNDERING. THE TYPE II, CLASS 1 LACE, WHEN MANUFACTURED WITH A POLYESTER FILL, SHALL NOT SHRINK OR ELONGATE MORE THAN 1 PERCENT IN THE WARP DIRECTION AFTER 3

COMPLETE LAUNDERING CYCLES WHEN TESTED AS SPECIFIED IN 4.4.3."

PAGE 13, ADD THE FOLLOWING NEW PARAGRAPH:

"3.10 TOXICITY. THE FINISHED LACE SHALL NOT PRESENT A HEALTH HAZARD AND SHALL SHOW COMPATIBILITY WITH PROLONGED, DIRECT SKIN CONTACT WHEN TESTED AS SPECIFIED IN 4.4.3. CHEMICALS RECOGNIZED BY THE

ENVIRONMENTAL PROTECTION AGENCY (EPA) AS HUMAN CARCINOGENS SHALL NOT BE USED."

PAGE 19, IN TABLE VIII, UNDER "LACE ONLY", ADD THE FOLLOWING IN THEIR RESPECTIVE COLUMNS:

"DIMENSIONAL CHANGE:

TO DRY-CLEANING (1 CYCLE) 3.6.4 AATCC 158 5/

TO LAUNDERING (3 CYCLES) 3.6.4.1 AATCC 135 6/"

PAGE 19, IN TABLE VIII, UNDER "BRAID AND LACE" ADD THE FOLLOWING IN THEIR RESPECTIVE COLUMNS:

"TOXICITY 3.10 4.5.2"

PAGE 20, ADD THE FOLLOWING FOOTNOTES:

"5/ EXCEPT THE SPECIMEN SHALL BE 20-INCHES LONG AND FULL WIDTH.

6/ MACHINE CYCLE, PERMANENT PRESS; WASH TEMPERATURE, 120 + 5 degree F; TUMBLE DRY, PERMANENT

PRESS."

PAGE 21: ADD THE FOLLOWING NEW PARAGRAPH:

"4.5.2 TOXICITY TEST. IF THE TOXICITY REQUIREMENT (SEE 3.10) CAN BE DEMONSTRATED WITH HISTORICAL DATA, TOXICITY TESTING MAY NOT BE REQUIRED (SEE 6.2). WHEN REQUIRED (SEE 6.2), AN ACUTE DERMAL IRRITATION STUDY AND A SKIN SENSITIZATION STUDY SHALL BE CONDUCTED. WHEN THE RESULTS OF THE STUDIES INDICATE THE BRAID IS NOT A SENSITIZER OR IRRITANT, A REPEAT INSULT PATCH TEST SHALL BE PERFORMED IN

ACCORDANCE WITH THE MODIFIED DRAIZE PROCEDURE (SEE 2.2). "

PAGE 23, 6.2, ADD THE FOLLOWING:

"K. TOXICITY REQUIREMENTS (SEE 3.10 AND 4.5.2)."

(Ref. T1574)

A-A-52067 BINDING, TEXTILE, COTTON,

. BIAS-CUT, DATED 3/13/90

ADDITIONAL INFORMATION FOR MIL-P-15064:

INTERIM CHANGE TO MIL-P-15064G:

AS AN ALTERNATE PADS, SHOULDER AND SLEEVE-HEAD ADD "BLEACHED MUSLINETTE".

PAGE R, PARAGRAPH 3.2.1 PRINT CLOTH. ADD THE

FOLLOWING SENTENCE AT THE END OF THE PARAGRAPH

"AS AN ALTERNATE, THE TYPE IV SLEEVE-HEAD OUTER

COVER SHALL BE 100% COTTON MUSLIN WITH A MINUMUM OF 44 WARP AND 36 FILLING YARNS PER SQUARE INCH.

TABLE I. MATERIAL REQUIREMENTS, ADD THE FOLLOWING INFORMATION TO THE TABLE.

TYPE IV 44 BY 36"

PAGE 4: PARA. 3.2.2.1, LINE 2, AFTER "CLASS 1":

ADD "OR CLASS 2".

PAGE 4: PARA. 3.2.2.2,LINE 2, AFTER "UNBLEACHED"

ADD "OR BLEACHED".

PAGE 6, PARAGRAPH 3.2.6 WADDING. ADD THE FOLLOWING SENTENCE AT THE END OF THE PARAGRAPH. "AS AN ALTERNATE, THE TYPE IV SLEEVE-HEAD FILLER SHALL BE 100% PRENEEDLED COTTON FILLER, WEIGHING A MINIMUM OF 3.0 OUNCES PER SQUARE YARD AND A MAXIMUM OF 3.5 OUNCES PER SQUARE YARD" PAGE 8, ADD "PARAGRAPH 3.5.10 TYPE IV. AS AN ALTERNATE TYPE IV SLEEVE-HEAD SHALL MEASURE

15 INCHES (+/- 1/4 INCH) FOR MEN AND 13 INCHES (+/-1/4 INCH) FOR WOMEN."

PAGE 9, ADD THE FOLLOWING INFORMATION TO TABLE II.

TABLE II. MANUFACTURING OPERATIONS REQUIREMENTS-CONTINUED.

NO. REQUIRMENTS STITCH SEAM STITCHES THREAD

. TYPE TYPE PER INCH NDL BOB

1. CUTTING: "OR

C. THE MUSLIN SHALL BE SPLIT 3 INCHES (+/-1/8

INCH) IN THE BIAS DIRECTION."

2.CONSTRUCTION: "OR C. FOLD THE MUSLIN BIAS

STRIP TO FINISH TWO INCHES +/- 1/8 INCH. THE

COTTON FILLER WILL BE INSIDE THE FOLDED MUSLIN.

THE COTTON WILL BE CUT 2 -1/4 INCHES +/-1/8 INCH

WIDE. BOTH PIECES WILL BE SEWN WITH A STITCH

LINE APPROXIMATELY 1/2 INCH FROM THE FOLDED EDGE

OF THE SLEEVE HEAD. (SEE FIGURE 6, PAGE 37)"

301/401 EFA-1 3-4 70-2 70-2

PAGE 37, ADD FIGURE 6, SLEEVE HEAD, MAN'S AND

WOMEN'S TYPE IV."

ALTERNATE WOMEN'S PAD'S INSERT "B" REQUIREMENTS

THE SHOULDER PADS SHALL HAVE A TOP AND BOTTOM

COVER OF 4 OUNCES PER SQUARE YARD WHITE NEEDLE

PUNCHED POLYESTER FELT WHEN TESTED IN ACCORDANCE

WITH ASTM D-3776, OPTION C. THE FILLER SHALL BE

COTTON, ONE PIECE SHAPED TO FILL OUT THE PAD

WITH AN EVEN SMOOTH TAPER FROM CENTER TO ALL

EDGES. MULTIPLE PIECES ARE NOT ACCEPTABLE. THE

TOP COVER SHALL BE NOTCHED FOR SHOULDER SEAM

ALIGNMENT 4-3/4 INCHES FROM THE FRONT OF THE PAD

THE PAD SHALL BE SEWN IN A CONCAVE SHOULDER FIT-

TING FORM UTILIZING MULTI-LINE OF BASTING, TOTAL

ING 6 ROWS. THE PAD SHALL HAVE A COMPRESSED FIN-

ISHED THICKNESS MEASURING 3/8 +/- 1/8 INCH USING

A ONE INCH FOOT AT 0.1 PSI. THE FINISHED PAD

SHALL MEASURE 8-1/2 TO 9-1/2 INCHES IN LENGTH

AND 4-1/2 TO 5 INCHES IN WIDTH, WITH A 1/2 INCH

ARMHOLE CUTOUT ON EACH SIDE. THE PADS SHALL NOT

BE SIGNIFICANTLY ALTERED IN THICKNESS, SHAPE OR

DIMENSION AFTER BEING COMMERICALLY DRY CLEANED 3

TIMES WITH PERCHLOROETHELENE. THE PAD SHALL HAVE

A MINIMUM BREAKING STRENGTH OF 6.0 POUNDS IN THE

MACHINE DIRECTION AND A MINIMUM OF 3.0 POUNDS IN

IN THE CROSS DIRECTION WHEN TESTED IN ACCORDANCE

ASTM-D 5034, OPTION G-T OR G-E.

ALTERNATE MEN'S PAD'S INSERT "A" REQUIREMENTS

THE SHOULDER PADS SHALL HAVE A TOP AND BOTTOM

COVER OF 4 OUNCES PER SQUARE YARD WHITE NEEDLE

PUNCHED POLYESTER FELT WHEN TESTED IN ACCORDANCE

WITH ASTM D 3776, OPTON C. THE FILLER SHALL BE

COTTON, ONE PIECE SHAPED TO FILL OUT THE PAD

WITH AN EVEN SMOOTH TAPER FROM CENTER TO ALL

EDGES. MULTIPLE PIECES ARE NOT ACCEPTABLE. THE

TOP COVER SHALL BE NOTCHED FOR SHOULDER SEAM

ALIGNMENT 4-1/4 INCHES FROM THE FRONT OF THE PAD

THE PAD SHALL BE SEWN IN A CONCAVE SHOULDER FIT-

TING FORM UTILIZING MULTI-LINE OF BASTING, TOTAL

ING 6 ROWS. THE PAD SHALL HAVE A COMPRESSED FIN-

ISHED THICKNESS MEASURING 1/2 +/- 1/8 INCH USING

A ONE INCH FOOT AT 0.1 PSI. THE FINISHED PAD

SHALL MEASURE 9-3/4 TO 10/3/4 INCHES IN LENGTH

AND 5-3/8 TO 5-5/5 INCH IN WIDTH, WITH A 1/2 INCH

ARMHOLE CUTOUT ON EACH SIDE. THE PADS SHALL NOT

BE SIGNIFICATNLY ALTERED IN THICKNESS, SHADE OR

DIMENSION AFTER BEING COMMERCIALLY DRY CLEANED 3

TIMES WITH PERCHLOROETHELENE. THE PAD SHALL HAVE

A MINIMUM BREAKING STRENGTH OF 6.0 POUNDS IN THE

MACHINE DIRECTION AND MINIMUM OF 3.0 POUNDS IN

THE CROSS DIRECTION WHEN TESTED IN ACCORDANCE

WITH ASTM-D 5034, OPTION G-T OR G-E.

DEVIATION FROM MIL-P-15064F;

. PAGE 6, PARA. 3.5.1, LINE 4

. DELETE "7/8+1/8 INCH" AND

. SUBSTITUTE "1/2+1/8 INCH."

(Ref. T1553)

ADDITIONAL INFORMATION FOR MIL-C-16375:

NOTE. A-A-52097 HAS BEEN AUTHORIZED IN PREFERENCE TO MIL-C-16375

(Ref. T0997)

ADDITIONAL INFORMATION FOR A-A-52097:

NO ADDITIONAL INFORMATION FOLLOWS.

(Ref. T1569)

ADDITIONAL INFORMATION FOR MIL-C-29137:

NO ADDITIONAL INFORMATION FOLLOWS.

(Ref. T1562)

ADDITIONAL INFORMATION FOR MIL-C-43718:

MIL-C-43718C HAS BEEN CANCELLED A-A-52106 HAS BEEN AUTHORIZED AS A REPLACEMENT

ADDITIONAL INFORMATION FOR A-A-52106:

INTERIM CHANGES TO A-A-52106:

PAGE 1, UNDER ABSTRACT. AFTER "THE CLASS 3 CLOTH IS

INTENDED FOR USE AS LINING MATERIAL IN DRESS COATS."

ADD "CLASS 4 CLOTH IS INTENDED TO BE USED AS A

GARMENT LINING. CLASS 5 CLOTH IS INTENDED FOR USE

AS A NECKTIE AND NECKTAB OUTERSHELL FABRIC."

PAGE 1, CLASSIFICATION. ADD CLASS 4 - LIGHT WEIGHT

2.4 OZ; 2/1 RIGHT HAND TWILL USING 100% FILAMENT

POLYESTER SINGLE PLY YARNS FOR BOTH CLASS 4 AND CLASS 5.

CLASS 5 - MEDIUM WEIGHT 3.0 OZ; 5/1 HERRINGBONE TWILL

PAGE 1, PARAGRAPH 1.1 CLASSIFICATION: ADD PAGE 1,

GENERAL DESCRIPTION. LINE 5 AFTER "YARNS" ADD

"THE CLASS 4 CLOTH SHALL BE A TW0 UP-ONE DOWN RIGHT

HAND TWILL. THE CLASS 5 CLOTH SHALL BE A FIVE UP-ONE

DOWN HERRINGBONE TWILL. THE YARNS FOR CLASS 4 CLOTH

SHALL BE SINGLE PLY WITH A NOMINAL DENIER OF 70 FOR

THE WARP YARNS AND 150 FOR THE FILLING YARNS.

PAGE 2, TABLE I CLOTH REQUIREMENTS AFTER CLASS 3"

ADD INFORMATION FOR "CLASSES 4 AND 5"

CHARACTERISTIC CLASS 4 CLASS 5

MATERIAL CONTENT, PERCENT:

POLYESTER 100% 100%

COTTON 0 0

RAYON 0 0

COLORFASTNESS TO:

PERSPIRATION GOOD GOOD

SUBLIMATION GOOD GOOD

WET DRY-CLEANING GOOD GOOD

CROCKING (MIN.) 3.5 3/ 3.5 3/

(BLACK OR DARK

BLUE COLORS) 1.0 3/ 1.0 3/

LABILE SULFUR CONTENT 4/ 4/

WEIGHT, OZ. /SQ. YD.(MIN.) 2.4 3.0

YARNS PER INCH (MIN.)

WARP 124 140

FILLING 76 75

BREAKING STRENGTH POUNDS (MIN.)

WARP 140 160

FILLING 110 130

TEARING STRENGTH POUNDS (MIN.)

WARP 5.0 14.0

FILLING 3.0 10.5

PAGE 2, PARAGRAPH 2.1 GENERAL DESCRIPTION: AFTER

"THE CLASS 5 CLOTH SHALL BE A FIVE UP-ONE DOWN

"THE CLASS 5 CLOTH, USING 100 % FILAMENT HERRINGBONE

TWILL." INSERT "THE CLASS 6 CLOTH POLYESTER SINGLE PLY

WITH BLACK 70 DENIER NOMINAL WARP AND AIR FORCE

BLUE 1622 150 DENIER NOMINAL FILLING YARNS." USING

100% FILAMENT POLYESTER SINGLE PLY WITH 70 DENIER NOMINAL

IN THE WARP AND 150 DENIER NOMINAL IN THE FILLING DIRECTION."

PAGE 2, PARAGRAPH 2.2 PHYSICAL REQUIREMENTS:

TABLE I. CLOTH REQUIREMENTS, ADD THE FOLLOWING:

PAGE 3, AFTER 2.3 LENGTH AND PUT-UP. ADD THE FOLLOWING

NEW PARAGRAPH: "2.4 COLOR. THE COLOR OF THE FINISHED

CLOTH SHALL BE AS SPECIFIED (SEE 5.1) AND SHALL MATCH THE STANDARD SAMPLE FOR SHADE. CLASS 5 FABRIC

IS MADE

FROM DYED WARP AND DYED FILLING IN TWO DIFFERENT COLORS.

CLASS 5 FABRIC SHALL BE AIR FORCE SHADE BLUE 1622 ROLL #89-2.

(ref. T1514 - 5/23/06)

INSPECTION OF SUPPLIES SHALL BE IN ACCORDANCE WITH FAR PART 52.246-2 STANDARD INSPECTION.

ADDITIONAL INFORMATION FOR MIL-B-3461:

MIL-B-3461G BUTTON, INSIGNIA, METAL,

. UNIFORM AND CAP, 9/30/79;

. AMENDMENT 6 DTD 6/24/03

NO ADDITIONAL INFORMATION FOLLOWS.

INTERIM CHANGES TO MIL-B-3461G:

PAGE 2, UNDER TYPE I, STYLE 3, ADD "CLASS B -

BLACK ENAMELED, SUBCLASS 1, LOW CONTOUR."

PAGE 6, PARA. 3.6.1.2, ADD AT END "TYPE I, STYLE

3 BUTTON SHANKS MAY BE SWEDGED BY A COLD HEADED

PROCESS IN LIEU OF SOLDERING. THE COLD HEADED

PROCESS WILL REQUIRE PRIOR APROVAL OF PROCESS

USED TO ENSURE SHANKS ARE NOT LOOSE OR WOBBLY."

PAGE 8, PARA. 3.6.2.2, LINE 6, DELETE "EXCEPT

FOR STYLE 3 (MC) BUTTONS" AND DELETE LAST

SENTENCE ENTIRELY.

PAGE 11, TABLE IV, FINISH, UNDER TYPE I, STYLE 3

ADD "CLASS B-DULL BLACK ENAMEL FINISH."

PAGE 22, PARA. 5.1.1.1.1, LINE 1, DELETE "TYPE I

STYLE 3". PARA. 5.1.1.1.1.1, IN TITLE, DELETE

"TYPE I, STYLE 3 AND".

PAGE 26, PARA. 5.2.2, TABLE IX, UNDER "STYLE 3-

MARINE CORPS REGULAR SHANK - 40" DELETE "2, 880-

CARDED - 20" AND SUBSTITUTE "4,032 - BULK 28",

UNDER "REGULAR SHANK - 27" DELETE "8,640 -CARDED

60" AND SUBSTITUTE "6,048 - BULK-42", ADD "SHORT

SHANK-27-6,048 - BULK 42".

2. ALL OTHER TERMS AND CONDITIONS REMAIN THE SAME.