SPE1C1-21-R0005 Combined Synopsis_Solicitation.pdf

Combined Synopsis & Solicitation

This is a combined synopsis/solicitation for commercial items prepared in accordance with the format in Subpart 12.6, as supplemented with additional information included in this notice. This announcement constitutes the only solicitation; quotations are being requested and a written solicitation will not be issued.

A. Pursuant to FAR 12.603, the following information is provided:

1. Solicitation Number: _SPE1C1-21-R-0005__. The solicitation is issued as a request for proposal

(RFP).

2. All proposed unit prices shall be submitted in United States Currency: U.S. Dollars

3. The solicitation is issued as SMALL BUSINESS SET ASIDE.

B. Responses to the solicitation shall be made in writing to the contracting officer by 3:00

PM Eastern Standard Time on November, 13, 2020. Submissions by electronic correspondence are accepted and can be sent to the following email address:

Randall.mcarthur@dla.mil

CAUTION NOTICES

BERRY AMENDMEND COMPLIANCE

Offerors are cautioned that all components must be of domestic origin in compliance with DFARS clause 252.225-7012, Preference for Certain Domestic Commodities (Dec 2017), as contained in Section I of this solicitation.

Section 833 of the National Defense Authorization Act for Fiscal Year 2007 added language to 10 U.S.C. 2533a requiring that all articles or items of "clothing", including the materials and components thereof, purchased by the Department of Defense be grown, reprocessed, reused, or produced in the United States, other than sensors, electronics, or other items added to, and not normally associated with, clothing (and the materials and components thereof).

ELECTRONIC INVOICING AND ADVANCED SHIPMENT

NOTIFICATIONS (ASN)

The Directorate of Clothing and Textiles (C&T) requires electronic invoicing on all contracts unless another method is mutually agreed to by the Contractor, the Contracting Officer, the contract administration office, and the payment office.

Utilization of Wide Area Workflow - Receipts and Acceptance (WAWF-RA) in conjunction with DFARS 252.232-7003, ELECTRONIC SUBMISSION OF PAYMENT REQUESTS

AND RECEIVING REPORTS (JUN

2012).

The Directorate of Clothing and Textiles utilizes VIM-ASAP, which is short for DLA Virtual Item Manager ARN Supply-Chain Automated Processing, to transmit data to WAWF-RA. VIM-http://farsite.hill.af.mil/reghtml/regs/far2afmcfars/fardfars/far/12.htm#P295_49271

ASAP is the only authorized method to electronically process requests for payment to WAWF- RA for the Directorate of Clothing and Textiles. VIM-ASAP will give you visibility of contract information, track production status and print labels. VIM-ASAP pre-populates contract data on your invoices, such as unit price, contract numbers, item numbers, addresses, and many other fields that will save you labor and time.

Advanced Shipment Notifications (ASNs) associated with DFARS clause 252.211-7006, PASSIVE RADIO FREQUENCY IDENTIFICATION (MAR 2018) are sent via VIM-ASAP to WAWF-RA processes.

Please contact the VIM-ASAP help desk at 888-940-7348 to get started today!

For questions about sending Electronic Data Interchange invoices (810-invoice transactions), contact Mr. Bud Wellens at 1-215-737-2778

For questions about invoice preparation, just call the DFAS Customer Service Resource Center at 1-800-756-4571, or Call DSCP DFAS liaisons listed below for assistance: Camille Conaway 1-215-737-4406

Check out these resources:

http://www.dfas.mil/money/vendor/ …. the DFAS Contract Payment Booklet… an excellent desk reference for contractor Accounts Receivable personnel, as well as the status of outstanding invoices.

http://www.dfas.mil/ …. information regarding bill paying process and additional points of contact

E-VERIFY

Pursuant to FAR clause 52.222-54 vendors are required to enroll in the E-Verify program within thirty days after the date of a contract award and comply with all terms of the clause. In addition, vendors are required to provide evidence of their enrollment in the E-verify program to the contracting officer within 30 days after the date of a contract award.

LATE BIDS

It is the Offerors responsibility to ensure that offers reach the Government office designated in the solicitation on time.

TECHNICAL DOCUMENT REQUESTS

DLA-Troop Support has developed a web-based system that allows manufacturers the ability to request specifications, patterns and drawings on our contracting page. To request technical data for DLA Troop Support Clothing and Textiles (C&T) solicitations, use the following link to the DLA-Troop Support C&T Technical Data Repository area at https://www.dla.mil/TroopSupport/ClothingandTextiles/SpecRequest.aspx http://www.dfas.mil/money/vendor/ http://www.dfas.mil/ https://www.dla.mil/TroopSupport/ClothingandTextiles/SpecRequest.aspx

PATIENT PROTECTION AND AFFORDABLE HEALTH CARE ACT

Please note that the Patient Protection and Affordable Health Care Act ("the Act"), 124 Stat. 119, imposes duties upon employers concerning the provision of health care to their employees. Health insurance costs, including any costs associated with compliance with changes in the applicable law, are the sole responsibility of the offeror. Offerors are advised that their proposals should include any costs associated with the implementation of the Act. Any changes in health coverage costs and/or costs associated with compliance, occurring after award of a contract pursuant to this solicitation will not form the basis for an equitable adjustment of the contract price.

PRE-PRODUCTION SAMPLE EVALUATIONS

Production Demonstration Models (PDMs) are not required for this acquisition; However, pre-production samples of the below item may be required after award. Note that the pre-production samples will be evaluated using the patterns and specifications provided in this solicitation. All previous versions and variations of patterns and specifications for this item are irrelevant.

It is preferred that the materials used to manufacture the Pre-Production Samples be in accordance with any specifications defined in this solicitation. However, if the offeror uses alternate materials to manufacture the Pre-Production Samples a letter must be supplied with them stating (i) which materials depart from the end item specification and (ii) that, although the materials used in producing the Pre-Production Samples differ from those specified, the materials required by the specification will be utilized under any resultant contract.

Note: The use of alternate materials will not affect the rating of the Pre-Production Samples, either favorably or negatively when the use of the alternate materials is identified in accordance with the requirements of this section. However, the Government reserves the right to give a negative rating to (a) Pre-Production Samples that is (are) made with materials that depart from the end item specification and the use of those alternate materials was not identified in accordance with the requirements of this section. Accordingly, to preclude a negative assessment of a Pre-Production Samples that is comprised of materials that are not in accordance with the specification(s), it is in the offeror's best interest to identify any and all alternate materials that have been used.

Although the offeror is permitted to use alternate materials to construct the Pre-Production Samples, the offeror is not permitted to utilize alternate manufacturing operations or change the construction/design of the Pre-Production Samples. The Pre-Production Samples must be manufactured (i) at the same facility as the production quantity and (ii) must be in accordance with applicable specifications, including the placement of the labels, unless otherwise identified.

However, labels need not be printed for the purpose of the Pre-Production Samples but there must be an indication as to the size of the Pre-Production Samples, when applicable. Therefore, prospective vendors must identify the facility or facilities were the Pre-Production Samples were manufactured.

RFID NOTICE TO DLA SUPPLIERS

This solicitation contains DFARS clause 252.211-7006, PASSIVE RADIO FREQUENCY

IDENTIFICATION (MAR 2018)

This clause requires the successful awardee(s) to affix passive RFID tags, at the case and palletized unit load levels. The successful awardee(s) is also required to electronically submit advance shipment notices to DOD, to permit association of the passive RFID tag data with the corresponding shipment.

Advance shipment notice. The Contractor shall use Wide Area Work Flow (WAWF), as required by DFARS 252.232-7003 (JUN 2012), Electronic Submission of Payment Requests, to electronically submit advance shipment notice(s) with the RFID tag ID(s) (specified in paragraph

(d) of this clause) in advance of the shipment in accordance with the procedures at https://wawf.eb.mil/.

Procurement Technical Assistance Centers (PTACS) are available to deliver passive RFID assistance to DOD suppliers. See http://www.dla.mil/db/procurem.htm to identify your local PTAC and obtain information on upcoming workshops and other training/outreach services.

NOTE: Tagging is also required at the item level. Each jacket will need to have an RFID Tag. Cost of implementing the item level RFID tagging must be included in the offered price.

RFID HANGTAG:

An RFID inlay shall be added to the barcode paper hang tag attached to each item. Where the use of self-adhesive bar- code labels are authorized, the RFID inlay may be added to the self-adhesive label in lieu of a paper hang tag. All other contract barcode and hang tag requirements still apply.

The RFID inlay should be passive Gen2 with a frequency range between 860 and 960 MHz. The RFID antenna should be Avery/Dennison AD222 or comparable with ISO/IEC 18000-C EPC global C1G2 Protocol and an EPC memory allocation containing a 96 bit EPC Number. The data linking the EPC number to the NSN and quantity unit pack must be exportable to VIM/ASAP.

The bar code of the EPC Number must be printed at the bottom of the tag along with the human readable version below the bar code.

In addition to defects applicable to the paper tag and barcoding element, the RFID tag shall be examined for the defects listed below:

RFID Inlay omitted RFID Inlay not secure RFID Inlay not readable with RFID scanner RFID Inlay or configuration not as specified

The manual document “Item-Level Passive RFID Technology Manufacturer's Information Guide" provides guidance and is available from the Contracting Officer.

SYSTEM FOR AWARD MANAGEMENT (SAM)

The System for Award Management (SAM) is combining federal procurement systems and the Catalog of Federal Domestic Assistance into one new system. This consolidation is being done in phases. The first phase of SAM includes the functionality from the following systems:

* Central Contractor Registry (CCR) http://www.dla.mil/db/procurem.htm

* Federal Agency Registration (Fedreg)

* Online Representations and Certifications Application

* Excluded Parties List System (EPLS)

All Contractors must register on the SAM website: https://www.sam.gov/portal/public/SAM/ in order to be considered for award.

Offerors are reminded to complete all applicable representations and certifications appearing in this solicitation. Failure to complete all representations and certifications may result in the offer being removed from award consideration for failure to comply with all terms and conditions of the solicitation.

Stop shipment delays and rejections!

For deliveries to New Cumberland depot, ensure your Government or Commercial Bills of Lading are correctly annotated with the following information in the description of articles:

Weight Pieces National Stock Number(s) (NSNs) Contract Number Shipment Number Door #s 113-134 - Mission Delivery (storage)

-- or --

Door #s 135-168 - Container Consolidation Point (CCP) Delivery (OCONUS)

(whichever applies to your freight)

Your truckers/dispatchers/ brokers/etc. should have this information readily available when they phone 717.770.6969 for a delivery appointment to Pre-Lodge.

Don't let the following common invoicing errors delay your payments any longer:

□ Missing or Erroneous Contract Number

□ Missing Call/Delivery Order Number

□ Missing or Erroneous Shipment Number

□ Failure to Mark DD250 as an Original Invoice

□ Failure to Distribute a Copy of the DD250 to the Contract Administration Office Terminal

□ Contract Line Item Number (CLIN) is Omitted, Incorrect or Does Not Match that Appearing in the Contract

□ Missing or Erroneous Unit of Issue

□ Quantity and Price are Incorrect

□ Wrong Pay Office on Invoice

Here are three things you can do to speed your invoice payments:

http://www.sam.gov/portal/public/SAM/

□ Be sure your original invoice is properly completed and legible.

□ Submit your invoices electronically using the Web Invoicing System (WInS). It's fast, accurate, and costs you nothing! Learn more at the WInS Home Page, at:

https://www.ecweb.dfas.mil/notes/,and start using WInS with your next invoice! Or

□ If you currently receive delivery orders electronically, you could benefit by using an

810- invoice transaction.

Web Invoicing eliminates postage, snail mail, and much paperwork, and gets the invoice/voucher into the DFAS system usually within 24 hours. Web Invoicing is free to vendors doing business with the Government. You just enter the appropriate information and send your invoice to DFAS electronically. It provides help text and pull-down menus in many fields. For more specific questions, contact Janice Hockman (703) 607-5111, Kirsten Larco (703) 607-4920 or

Debra Jones (703) 607-2082.

For questions about sending Electronic Data Interchange invoices (810-invoice transactions), contact Mr. Bud Wellens at (215) 737-2778

For questions about paper invoice preparation, just call the DFAS Customer Service Resource Center at 1-800 756-4571, or

Call DLA Troop Support DFAS liaisons listed below for assistance:

Camille Conaway (215) 737-4406

Check out these resources:

□ http://www.dfas.mil/money/vendor the DFAS Contract Payment Booklet… an excellent desk reference for contractor Accounts Receivable personnel, as well as the status of outstanding invoices.

□ http://www.dfas.mil/ information regarding bill paying process and additional points of contact.

QUALITY INSPECTION

Quality will be assured with the inclusion of DLA Troop Support Clothing and Textiles Additional Quality Assurance Requirements (formerly 4155.3) along with quality requirements of the end item specification.

Note: The changes* that follow update the DLA Troop Support Clothing & Textiles Additional Quality Assurance Requirements (formerly 4155.3) dated October 2018.

These changes* are not incorporated as yet in the attachment document.

Page 10 of 38, par. 2.1, line 4, after “(DCMA QAS)” add “, or Supplier’s Source Sampling Representative, as applicable” Page 11 of 38, par. 2.3, line 2, delete “to the source QAS”. Line 4, delete “source QAS” and replace with “Supplier’s Source Sampling Representative”.

Page 12, par 2.3 (continued), delete “source QAS” and replace with “Supplier’s Source Sampling Representative”.

Page 12 of 38, par. 2.4, line 5, delete “as required” and replace with “if required”.

Page 12 of 38, par. 3.1.1, after “entirely” add the following: “For routine shade or physical testing of fabric http://www.ecweb.dfas.mil/notes/%2Cand http://www.dfas.mil/money/vendor http://www.dfas.mil/ lots, Government sampling is not required. The DD Form 1222 for routine shade or physical testing of fabric lots shall be signed and dated by the Supplier’s Source Sampling Representative in Box 15.”

Page 13 of 38, par. 3.1.2 – line 10, after “Government QAS” add the following: “or Supplier’s Source Sampling Representative, as applicable,” Page 14 of 38, par. 3.2.1 – line 4, delete “source QAS” and replace with “Supplier’s Source Sampling Representative”.

Page 14 of 38, par. 3.2.1.1 – cutting swatches, delete “DCMA QAS” and replace with “Supplier’s Source Sampling Representative”. After “single color rolls – 4”x 24”” delete “QAS” and replace with “Supplier’s Source Sampling Representative”. After “multi-color camouflage”… delete “QAS” and replace with “Supplier’s Source Sampling Representative”.

Page 14 of 38, par. 3.2.1.2 – line 3, delete “stamped, “. Line 4, Delete “source QAS” and replace with “Supplier’s Source Sampling Representative” Page 15 of 38, par. 3.2.1.4 – subpar. 2, delete “source QAS” and replace with “Supplier’s Source Sampling Representative” Page 15 of 38, par. 3.2.2 – Line 3, delete “stamped,”, delete “source QAS” and replace with “Supplier’s Source Sampling Representative”. Line 4, delete “QAS” and replace with “Supplier’s Source Sampling Representative”.

Page 16 of 38, par. 3.3.1 – Line 2, after “(30)” add, “calendar”. Line 3 and Line 6, after “QAS” add, “or Supplier’s Source Sampling Representative” Page 16 of 38, par. 3.3.2 – Delete the paragraph in its entirety, including subparagraphs labeled “a” through “i”, and replace with the following:

“3.3.2. Contractor Furnished Material (CFM). DLA Troop Support Clothing and Textiles contracts require source sampling of CFM at finishing plants.

The following provisions apply to sample selection and lot acceptance.

(a)The samples shall be randomly selected by the Supplier’s Source Sampling Representative.

(b)Upon presentation of a lot, the Supplier’s Source Sampling Representative will draw samples and forward the samples to the contractor’s laboratory specified in the contract for testing.

(c)Shipment of Component Lots from the source to the prime contractor need not be deferred except for Government Acceptance Testing (i.e., shade evaluation). Commencement of production prior to receipt of a passing test report from the contractor’s authorized laboratory is solely at the contractor’s risk.

(d)The contractor will provide copies of Certificates of Compliance to the QAS.

(e)The contractor is required to ensure that a complete test report for all lots is furnished to the source’s QAS and the appropriate DLA-PTC representative.”

Pages 24, 25, 36 add to block 16: “By signing in box 15, I certify that the samples referenced above were randomly selected and represent the lot identified above.

Contractors shall ensure that blocks 2 and 15 of the form DD1222 are updated to reflect the correct information.

Historically, both blocks contained the information of the DCMA QAR and their stamp/signature. When contractor’s representative samples, these blocks shall include the contractor’s representative’s information. Block 17 shall still include the DCMA QAR to receive the results of the report even though they may not be sampling the material to be tested.

CONTRACTOR CODE OF BUSINESS ETHICS

FAR Part 3.1002(a) requires all government contractors to conduct themselves with the highest degree of integrity and honesty. Contractors should have a written code of business ethics and conduct within thirty days of award. To promote compliance with such code of business ethics and conduct, contractors should have an employee business ethics and compliance training program that facilitates timely discovery and disclosure of improper conduct in connection with government contracts and ensures corrective measures are promptly instituted and carried out. A contractor may be suspended and/or debarred for knowing failure by a principal to timely disclose to the government, in connection with the award, performance, or closeout of a government contract performed by the contractor or a subcontract awarded there under, credible evidence of a violation of federal criminal law involving fraud, conflict of interest, bribery, or gratuity violations found in title 18 of the United States Code or a violation of the False Claims Act. (31 U.S.C. 3729-3733)

If this solicitation or contract includes FAR clause 52.203-13 - CONTRACTOR CODE OF BUSINESS ETHICS AND CONDUCT; the contractor shall comply with the terms of the clause and have a written code of business ethics and conduct; exercise due diligence to prevent and detect criminal conduct; promote ethical conduct and a commitment to compliance with the law within their organization; and timely report any violations of federal criminal law involving fraud, conflict of interest, bribery or gratuity violations found in title 18 of the United States Code or any violations of the False Claims Act. (31 U.S.C. 3729-3733). When FAR 52.203-13 is included in the contract, contractors must provide a copy of its written code of business ethics and conduct to the contracting officer upon request by the contracting officer.

SUPPLIES AND PRICES

Men’s Air Force Lightweight Jacket NSN: 8405-01-298-6881(s)

*Prices are all to be based on FOB Destination only

Minimum

QTY

Annual Estimated

Qty

UNIT

OF

ISSUE

UNIT PRICE

SPECIAL

MEASUREMENT

PRICE

12,504 31,248

EA $

Delivery Schedule: 90 DAY PRODUCTION LEAD TIME AFTER AWARD.

Women’s Air Force Lightweight Jacket NSN: 8410-01-299-9636(s)

*Prices are all to be based on FOB Destination only

Minimum

QTY

Annual Estimated

Qty

UNIT

OF

ISSUE

UNIT PRICE

SPECIAL

MEASUREMENT

PRICE

5,448 13,632

EA $

Delivery Schedule: 90 DAY PRODUCTION LEAD TIME AFTER AWARD.

MAXIMUM CONTRACT LIMITATION: NOT TO EXCEED $7,000,000.00

The ordering period of the base term is from the effective date of award through 364 days thereafter. The Government may issue delivery orders during this timeframe and not to exceed the contract maximum dollar amount.

Delivery Destination: (All items except Special Measurements):

VSTZ:

Travis Association For The Blind AF & MC 3PL -Distribution Services 4512 South Pleasant Valley Road Austin, Texas 78744

*The Contracting Officer reserves the right to request Pre-Production Sample/s(PPS) for the Men’s and Women’s Air Force Lightweight Jackets.

If the Contracting Officer requests Pre-Production Sample/s(PPS), the samples are due within 30 days after date of award before production can begin:

Submit Samples to:

DLA Troop Support 700 Robbins Ave.

Philadelphia, PA 19111 Attn: Randall McArthur Bldg. 3 / WK Station 3A4041

MEN’S JACKET TECH DATA

AIR FORCE BLUE SHADE 1605 SHALL BE MADE IN ACCORDANCE WITH MIL-J-87250 AND THE

FOLLOWING INFORMATION:

ADDITIONAL INFORMATION FOR MIL-J-87250:

PATTERN DATE: 1 MARCH 1993

STANDARD SAMPLE OF BASIC CLOTH POLY/WOOL

GABARDINE, USAF COLOR BLUE, SHADE NO.

1605 IS AVAILABLE FOR SHADE AND COLORFASTNESS

PIECE NO. 11-02

STANDARD SAMPLE OF KNIT CUFF AND WAISTBAND, POLYESTER AF BLUE 1606 CONFORMING TO

MIL-C-3735, IS AVAILABLE FOR SHADE ON PIECE NUMBER 14-04

INTERIM CHANGES TO MIL-J-87250:

PAGE 2, PARA. 2.1.1: UNDER "SPECIFICATIONS, FEDERAL"

- ADD "V-T-295 THREAD, NYLON".

- DELETE "A-A-1696"

- DELETE "V-B-871"

- DELETE "V-F-106" AND INSERT "A-A-55634"

- DELETE "V-T-276" AND INSERT "A-A-52094".

- DELETE "V-T-280"

- DELETE "DDD-L-20" AND INSERT "MIL-DTL-32075"

- DELETE "PPP-B-601" AND INSERT "ASTM-D6251"

- DELETE "PPP-B-636" AND INSERT "ASTM-D1974 AND ASTM-D5118"

UNDER "SPECIFICATIONS, MILITARY"

- DELETE "MIL-P-116" AND INSERT "MIL-STD-2073"

- DELETE "MIL-F-21840" AND INSERT "A-A-55126"

- DELETE "MIL-T-43548" AND INSERT "A-A-50199"

- DELETE "MIL-C-43718" AND INSERT "A-A-52106"

UNDER "STANDARDS, FEDERAL"

- DELETE "FED-STD-751" AND INSERT "ASTM-D6193"

UNDER "STANDARDS, MILITARY"

- DELETE "MIL-STD-105" AND INSERT "MIL-STD-1916 OR ANSI/ASQ Z1.4"

PAGE 4:

- PARA. 3.3.1, LINE 2, AFTER "MIL-C-10176", INSERT, "EXCEPT REQUIREMENTS FOR SPONGING

SHALL NOT APPLY"

- PARA. 3.3.2, LINE 1, AFTER "SLEEVES", ADD

"INSIDE PATCH POCKET".

- PARA. 3.3.2 AT THE END OF THE PARAGRAPH

ADD: "AS AN ALTERNATE THE MATERIAL FOR THE RE-

MOVABLE LINERS OUTER LAYER, THE SLEEVE BINDING

THE PASS-THROUGH POCKETS AND THE EDGE BINDING

SHALL BE A NYLON TAFFETTA, CG BLUE 3376, CON-

TINUOUS FILAMENT, 70 DENIER, WEIGHING 1.9

(+/- 0.15) OZ./SQ. YARD.

THE MATERIAL SHALL HAVE 100 YARNS PER INCH (MIN)

IN THE WARP DIRECTION AND 68 YARNS PER INCH IN

FILLING DIRECTION (MIN), A MINIMUM BREAKING

STRENGTH OF 110 LBS. ( WARP) AND 85 LBS. (FILL),

AND MINIMUM TEARING STRENGTH OF 5.0 LBS, (WARP)

AND 3.5 LBS. (FILL). THE FINISHED MATERIAL SHALL

SHOW "GOOD" FASTNESS TO PERSPIRATION, DRY CLEAN-

ING AND LAUNDERING WITH WET/DRY CROCKING RATING

NOT LOWER THAN THAN 3.0 WHEN TESTED AS SPECIFIED

IN AATCC TEST METHODS 15, 132, 61&8 RESPECTIVELY

- PARA. 3.3.3, LINE 2, DELETE "CS100" AND

INSERT "CDS100".

- PARA. 3.3.3, LINE 3, AFTER "0.3", INSERT "."

AND DELETE "OR THERMOLITE T-0 HAVING A MINIMUM

WEIGHT OF 3.0 OUNCES...THICKNESS OF 0.3".

- PARA. 3.3.4, LINE 3, DELETE "MIL-F-21840" AND INSERT A-A-55126"

- PARA. 3.3.6, LINE 2, DELETE "3/4 TO 7/8 INCH

WIDE" AND INSERT "1-1/4 INCHES WIDE".

- PARA. 3.3.7, LINE 2, DELETE "MIL-C-43718" AND

INSERT "A-A-52106".

PAGE 5:

- PARA. 3.3.8, LINE 2, AFTER "MIL-C-3735",

ADD ", SHALL MEASURE 7-5/8 INCHES".

- PARA. 3.3.10, LINES 3 AND 4, DELETE "DDD-L-20" AND INSERT "MIL-DTL-32075".

PAGE 6:

- PARA. 3.3.11, DELETE ENTIRELY AND INSERT:

"3.3.11 SLIDE FASTENERS. THE SLIDE FASTENER FOR

THE FRONT CLOSURE SHALL CONFORM TO TYPE III,

STYLE 8, SIZE 5 OF A-A-55634. THE CHAIN SHALL BE

BRASS OR ALUMINUM WITH A SHORT TAB PULL. THE

TAPE SHALL BE COTTON/WARP AND NYLON FILLING OR

100% POLYESTER, AND SHALL BE DYED TO APPROX.

THE SHADE OF THE BASIC FABRIC. THE BRASS

COMPONENTS SHALL HAVE A BLACK CHEMICAL FINISH

AND THE ALL METAL COMPONENTS SHALL BE FROM THE

SAME CONTRACTOR. ALUMINUM COMPONENTS MAY HAVE A

BLACK CHEMICAL FINISH OR BLACK ENAMEL FINISH. AS

AN OPTION, A NICKEL-PLATED FINISH MAY BE USED ON

THE TOP STOP AND BOTTOM PIN AND BOX OF THE SLIDE

FASTENER."

- PARA. 3.3.12, DELETE PARAGRAPH ENTIRELY.

- PARA. 3.3.13, LINES 2 & 3, DELETE "TYPE IA3,

TICKET NO. 50 OR NO. 60, 3 PLY OF A-A-52094" AND

INSERT "TYPE I, TICKET NO. 50 OF A-A-52094".

- PARA 3.3.13, LINES 4 & 5, DELETE "MIL-T-43548.

THE THREAD FOR SEWING ON THE BUTTON...V-T-276."

AND INSERT "A-A-50199. AS AN ALTERNATE FOR

THE OVEREDGE PORTION OF STITCH TYPES 515, 516,

517, 518 AND 519, THE THREAD SHALL CONFORM TO

A-A-50199 TICKET NO. 100, TEX 25-30. AS AN

ALTERNATE, THE THREAD FOR QUILTING THE LINER MAY

ALSO BE NYLON, CONFORMING TO TYPE VII, CLASS A,

SIZE A OF A-A-59826."

- PARA. 3.3.14, DELETE PARAGRAPH ENTIRELY.

- PARA. 3.4, LINE 2, AFTER "COLLARSTAND", DELETE

"WITH A THROAT TAB THAT BUTTONS,".

.- PARA. 3.4, AT END, ADD "EACH JACKET SHALL HAVE

AN INSIDE PATCH POCKET ON THE LEFT SIDE."

- PARA. 3.5, LINE 2, DELETE "SIDE SEAMS,".

- PARA. 3.5, LINES 3 & 4, DELETE "FOR ARMHOLES

AND JOINING THE COLLARSTAND TO THE BODY; AND"

AND SUBSTITUTE "FOR ALL OTHER SEAMS EXCEPT".

- PARA. 3.5, LINE 4, AFTER "COLLAR", ADD "." AND

DELETE "AND STAND EXTENSION." ADD NEW SENTENCE

"THE SIDE SEAM ALLOWANCE FOR THE LINER SHALL BE

3/8 INCH TO ALLOW FOR SOME TRIMMING BY SERGER

(APPROXIMATELY 1/8 INCH) PER SEAM.".

- PARA. 3.5, AFTER LAST SENTENCE, ADD:

"MINOR MODIFICATIONS ARE PERMITTED WHERE

NECESSARY WHEN USING AUTOMATIC EQUIPMENT. THESE

MODIFICATIONS SHALL NOT ALTER THE DIMENSIONAL,

SERVICEABILITY, OR APPEARANCE REQUIREMENTS CITED

IN THE SPECIFICATION."

PAGE 7:

- TABLE I. LIST OF PATTERN PARTS:

- OPPOSITE "LINING" UNDER "UNDERSLEEVE" ADD

"INSIDE POCKET" IN PATTERN NOMENCLATURE COLUMN

AND "1" IN CUT PARTS COLUMN.

- UNDER PATTERN NOMENCLATURE, ADD:

"INSIDE LINING POCKET MARKER ALL SIZES

FINISHED SHAPER SIZE 32 - 38

FINISHED SHAPER SIZE 40 - 50"

- PARA 3.6.1, LINE 2, DELETE "TABLE II SHALL CONFORM TO FED-STD-751." AND INSERT "ASTM- D6193."

PAGE 9:

- OPER. 1.A. LINE 3, DELETE "BUTTONS, AND BUTTONHOLE;"

- OPER. 1.B, LINE 3, DELETE "2 INCHES" AND

INSERT "1 INCH".

- OPER. 1.C, LINES 5, 6, & 7, DELETE "26", "27"

"28" & SUBSTITUTE "27", "28", "30" RESPECTIVELY.

PAGE 10:

- OPER. 4.A, LINE 2, AFTER "SHOULDER LOOPS,"

INSERT "OUTERSHELL WAISTBAND EXTENSION PIECES,"

- OPER. 6.B, LINE 4, DELETE "2-1/2 INCHES" AND

SUBSTITUTE "2-3/8 (+ 1/8 INCH)".

- OPER. 6.B, LINE 5, DELETE "2" AND SUBSTITUTE

"1-7/8 (+ 1/8 INCH)".

- OPER. 6.B, LINE 6, DELETE "AT THE NECK" AND

SUBSTITUTE "AT THE BASE OF THE POINT."

PAGE 11:

- OPER. 8.A, LINE 6, DELETE "AROUND THE STAND

EXTENSION".

- OPER. 8.NOTE, LINE 2, DELETE "3-1/8 (+/- 1/8)"

AND SUBSTITUTE "3-3/8 (+/- 1/8)".

- OPER. 8.NOTE, ADD AT END "FINISHED WIDTH OF

COLLARSTAND AT CENTER BACK, SHALL BE 1-3/4

(+/- 1/8) INCH WIDE."

PAGE 12:

- OPER. 9.B:

-- LINES 2 & 3, DELETE "BACK-STITCHED OR".

-- DELETE "301 OR" FROM STITCH TYPE COLUMN AND

ADD "28 PER BARTACK" IN STITCHES PER INCH COLUMN

PAGE 13:

- PRIOR T0 OPER. 12.A, ADD: "NOTE: AUTOMATED POCKETING EQUIPMENT MAY BE USED TO

PERFORM THIS OPERATION."

- OPER 12.I, LINE 1, AFTER "JOINING" ADD "FRONT"

PAGE 14, BEFORE OPER. 15, ADD NEW OPERATION:

"MAKE AND ATTACH INSIDE PATCH POCKET.

A. FOLD POCKET IN HALF WIDTH WISE AND STITCH

1/2 INCH FROM THE TOP FOLDED EDGE.

301 SSA-1 10 - 14

B. TURN TOP OF POCKET, WITH THE SIDE AND BOTTOM

EVEN, PRESS POCKET FLAT.

C. PLACE POCKET AT PATTERN MARKS AND ATTACH TO

LINING, AT THE FOLDED EDGE OF THE POCKET, ATTACH

1/16 INCH FROM THE EDGE, CONTINUE THE STITCHING

3/16 TO 1/4 INCH ACROSS THE TOP OF THE PATCH

POCKET AND 1/2 TO 5/8 IN A DIAGONAL DOWN TO THE

LINE OF THE 1/16 INCH STITCHING.

301 SSA-1 10 - 14

NOTE:

FOR SIZES 32 - 38, THE TOP OPENING SHALL FINISH

4-3/4 (+/- 1/8) INCHES.

FOR SIZES 40 - 50, THE TOP OPENING SHALL FINISH

5-1/4 (+/- 1/8) INCHES."

PAGE 15:

- OPER. 16.B, IN "SEAM AND STITCH TYPE" COLUMN,

DELETE "SSA-1" AND SUBSTITUTE "LSS-2".

- OPER. 17.B, LINE 4, DELETE "9 +/- 1/2 INCHES

FROM BOTTOM OF JACKET." AND SUBSTITUTE

"1/4 (+/- 1/8) INCH BELOW THE MIDDLE PILE

FASTENER TAPE.".

PAGE 16, OPERS. 20.A THRU 20.C, DELETE ENTIRELY

AND SUBSTITUTE AS FOLLOWS:

"A. THE LOOPS SHALL BE CENTERED ON THE SHOULDER

SEAMS IN ACCORDANCE WITH THE NOTCHES ON THE

PATTERNS AND STITCHED TO THE ARMHOLE 1/4 TO 3/8

INCH FROM COLLARSTAND SEAM.

301 SSA-1 10 - 14

B. JOIN THE SLEEVES TO THE JACKET, CATCHING THE

SHOULDER LOOPS IN SEAM.

301 SSA-1 10 - 14

C. PRESS SEAM FLAT AND TOWARD SLEEVE.

D. ATTACH SHOULDER LOOPS TO JACKET, STITCHING

FROM SHOULDER POINT TO CENTER POINT TO SHOULDER

LOOP POINT.

301 SSA-1 10 - 14"

PAGE 17:

- OPER. 22.E, DELETE "AND PRESS".

- AFTER OPER. 22.E, DELETE "NOTE" ENTIRELY AND

SUBSTITUTE THE FOLLOWING:

"NOTE: FINISHED CUFF SHALL MEASURE 3 (+/- 1/8)

INCHES WIDE FOR SIZES 34 THRU 40 AND 3-3/4

(+/- 1/8) INCHES WIDE FOR SIZES 42 THRU 50."

- OPER. 23, IN TITLE, AFTER "TAPE", ADD "TO

JACKET". LINE 2, BEFORE "FACING", ADD "JACKET".

ADDITIONAL INTERIM CHANGES TO MIL-J-87250:

PAGE 4, PARA. 3.3.3, "INSULATING CLOTH" DELETE

IN ITS ENTIRETY AND SUBSTITUTE "3.3.3 INSULAT-

ING CLOTH. THE INSULATING CLOTH FOR THE LINER

SHALL HAVE DUAL SCRIM.THE BATTING SHALL BE COMP-

OSED OF 65% POLYOLEFIN/35% POLYESTER (EXCLUDING

SCRIM), WITH A MINIMUM WEIGHT OF 3.0 OZ/YD (EX-

CLUDING SCRIM) AND A MINIMUM THICKNESS OF 0.3

INCHES. THE MINIMUM R VALUE FOR WARMTH SHALL BE

1.14.THE INSULATING CLOTH SHALL BE DRY CLEANABLE

AND MACHINE WASHABLE. CERTIFICATES OF COMPLIANCE

SHALL BE SUBMITTED FOR ALL REQUIREMENTS, AND THE

GOVERNMENT RESERVES THE RIGHT TO INSPECT SUCH

COMPONENTS TO DETERMINE THE VALIDITY OF THE

CERTIFICATION."

PAGE 4, PARA. 3.3.6, LINE 2, AFTER "1-1/4" ADD

"(+/- 1/8)."

PAGE 6, OPER. 3.3.13. LINE 1, DELETE THE WORD

"BUTTONHOLE MAKING." LINE 2, DELETE "RAYON"

PAGE 16, OPER. 20B DELETE "TOWARD SLEEVE" AND

SUBSTITUTE "AWAY FROM SLEEVE".

PAGE 18:

- OPER. 25.B, LINE 3, AFTER "STITCHING" ADD

"1/2 INCH".

- OPER. 26.A, LINE 1, DELETE"ON" AND SUBSTITUTE

"BETWEEN".

- OPER. 26.A, LINE 3, DELETE "STITCH THROUGH

BOTH PLIES," AND SUBSTITUTE "THE FACING. STITCH

THROUGH ALL PLIES,".

- OPER 26.B & 26.C,DELETE ENTIRELY & SUBSTITUTE

"B. TURN AND ROLL THE FRONT EDGE OF THE OUTER

SHELL OUT SO THAT THE CHAIN IS COVERED AND

STITCH 3/8 TO 1/2 INCH FROM THE FOLDED OUTER

SHELL & 1/8 INCH FROM THE FACING (SEE FIGURE 1)"

PAGE 19, OPERS. 29 AND 30, DELETE ENTIRELY.

PAGE 23, TABLE III, "FINISHED MEASUREMENTS":

- IN "BACK" COLUMN FOR SHORT, REGULAR, LONG AND

EXTRA LONG, SUBTRACT 1/2 INCH FROM ALL SIZES.

- IN "COLLAR" COLUMN FOR SHORT, REGULAR, LONG

AND EXTRA LONG, ADD 1/2 INCH FOR ALL SIZES.

PAGE 24, FOOTNOTE 4/, LINE 1, DELETE "LONG" AND

SUBSTITUTE "ALONG".

PAGE 28, PARA 4.4.3.1, LINES 5 & 6, DELETE "2.5"

"15.0" AND "40.0" AND SUBSTITUTE "1.5", "10"

AND "25" RESPECTIVELY.

PAGES 32 & 33, TABLE VI. "GENERAL DEFECTS",

DELETE DEFECTS 7 & 8 ENTIRELY.

PAGE 35, TABLE VII."DEFECTS APPLICABLE TO

SPECIFIC PARTS", DEFECT 3:

- LINE 5, DELETE "2-5/8 INCHES" AND SUBSTITUTE

"2-7/8 INCHES".

- LINE 6, DELETE "2-7/8 INCHES" AND SUBSTITUTE

3-1/8 INCHES".

PAGE 38, TABLE VII. "DEFECTS APPLICABLE TO

SPECIFIC PARTS", DEFECT 11:

- LINE 3, AFTER "JACKET", DELETE "(HOOK TAPE)".

- LINE 4, AFTER "LINER", DELETE "(LOOP PILE

TAPE)".

PAGE 42, PARA 6.6, LINES 7-10, DELETE

"THERMOLITE...19880-0705".

AQL'S:

END ITEM DIMENSIONAL 4.0

VISUAL 6.5

ACCEPTABILITY OF LOTS WILL BE DETERMINED BY THE

INSPECTION BY ATTRIBUTES, ANSI/AQSC Z1.4

GENERAL INSPECTION LEVEL 2".

(Ref. W2088)

PACKAGING:

LARGE QUANTIES SHOULD BE SHIPPED IN THE STANDARD UNIT PACK (12 UNITS) CITED IN THE END ITEM SPECIFICATION - HANGER PACK. ALL REQUISITIONS FOR FULL UNITS OF PACK ARE

REQUIRED TO BE HANGER PACKED WHEN SHIPPING LESS THAN FULL UNITS OF PACK, THE

CONTRACTOR IS ALLOWED TO SHIP ACCORDING TO BEST COMMERCIAL PRACTICE.

DELETE CURRENT "BARCODE LABEL/TAG" REQUIREMENTS AND SUBSTITUTE THE FOLLOWING:

LABEL TAG: EACH ITEM SHALL BE INDIVIDUALLY BAR-CODED WITH A PAPER TAG FOR

PERSONAL CLOTHING ITEMS. THE PAPER USED FOR THE TAGS SHALL BE STANDARD BLEACHED

SULFATE HAVING A BASIS WEIGHT OF 100 POUNDS WITH A SMOOTH FINISH TO ACCEPT

THERMAL TRANSFER AND DIRECT PRINTING. THE TAGS SHALL HAVE A HOLE AND SHALL BE

ATTACHED TO EACH ITEM BY A FASTENER, CLEARLY LEGIBLE AND READABLE BY SCANNER.

THE BAR CODING ELEMENT SHALL BE A 13 DIGIT

NATIONAL STOCK NUMBER (NSN). THERE SHALL BE A 12 DIGIT UNIVERSAL PRODUCT CODE (UPC)

ASSIGNED FOR ALL NSNS BY THE GOVERNMENT. THE INITIAL "UPC" MUST APPEAR BENEATH

THE CODE. THE BAR CODES FOR NSN AND UPC SHALL BE A MEDIUM TO HIGH DENSITY AND

SHALL BE LOCATED SO THAT THEY ARE COMPLETELY VISIBLE ON THE ITEM WHEN IT IS FOLDED AND PACKAGED AS SPECIFIED. THE LABEL'S LOCATION SHALL CAUSE NO DAMAGE TO THE ITEM.

NOTE: UNIVERSAL PRODUCT CODE INFORMATION THE GOVERMENT ASSIGNED UNIVERSAL

PRODUCT CODE (UPC) MUST BE PLACED ON ALL SHIPPING CARTONS ON WHICH THE NSN

APPEARS.

THE FOLLOWING DEFECTS APPLY FOR BARCODE LABELS/TAGS:

BAR CODE OMITTED OR NOT READABLE BY SCANNER

HUMAN-READABLE INTERPRETATION (HRI) OMITTED OR ILLEGIBLE

NOT VISIBLE ON FOLDED, PACKAGED ITEM CAUSES DAMAGE TO THE ITEM

NOTE: IF THE END ITEM IS PLACED IN A PLASTIC BAG - USE TYPE VII (PRESSURE SENSTIVE

LABEL) OF MIL-DTL-32075.

IF THE END ITEM IS TIED IN A BUNDLE OR LEFT AS AN INDIVIDUAL ITEM, USE TYPE VIII (TAG, PAPER) OF MIL-DTL-32075.

ADDITIONAL INFORMATION FOR A-A-50083:

ADD THE FOLLOWING INTERIM CHANGES:

PAGE 1, PARA. 1.2, DELETE SECOND SENTENCE ENTIRELY, AND SUBSTITUTE "THE THICKNESS OF

THE MATERIAL SHALL BE 0.0010 TO 0.0090 INCHES IN ACCORDANCE WITH L-P-378."

(ref. T0894 - 5/23/06)

INTERIM CHANGES TO A-A-52094:

NO CHANGES

INTERIM STANDARD SAMPLE FOR FOLIAGE GRFEEN 504

IDENTIFIED AS ROLL #3721 (THE FOLIAGE GREEN 502

AREA OF THE PATTERN CLOTH MIL-C-44436), AND REFERENCED

FOR SHADE ONLY. THIS STANDARD IS TEMPORARY UNTIL FURTHER

NOTICE.

ADDITIONAL INFORMATION FOR NN-P-71:

NO ADDITIONAL INFORMATION FOLLOWS..

ADDITIONAL INFORMATION FOR MIL-I-45208:

NOTE: MIL-I-45208 HAS BEEN CANCELLED AND REPLACED BY THE FOLLOWING: INTERNATIONAL

STANDARDS ISO 9001:2008

OR AMERICAN SOCIETY FOR QUALITY ASQ 2008 VERSION.

(ref. T1286 )

"MIL-DTL-32075: LABEL FOR CLOTHING, EQUIPAGE,

AND TENTAGE, GENERAL USE REPLACES DDD-L-20

(Ref. T0451 - June 19, 2007)

INTERIM SPECIFICATION CHANGES TO MIL-DTL-32075:

PAGE 6, TABLE I, "PHYSICAL REQUIREMENTS OF THE

TYPE VI FINISHED LABEL." UNDER "TEARING

STRENGTH" DELETE: "(LB.) MINIMUM" AND

SUBSTITUTE: "(GNS) MINIMUM."

PAGE 12, PARA 3.3.2.17, AFTER "NSN" ADD

"AND THE UNIVERSAL PRODUCT CODE (UPC)

SUPPLIED BY THE GOVERNMENT, FOR ALL NSNs."

PAGE 1, PARA. 1.2, DELETE SECOND SENTENCE ENTIRELY, AND SUBSTITUTE "THE THICKNESS OF

THE MATERIAL SHALL BE 0.0010 TO 0.0090 INCHES IN ACCORDANCE WITH L-P-378."

(ref. T0894 - 5/23/06)

ADDITIONAL INFORMATION FOR MIL-C-3735:

STANDARD SAMPLE FOR SAGE GREEN 1590 IS IDENTIFIED AS PIECE #52 AND REFERENCED FOR

SHADE ONLY.

INTERIM STANDARD SAMPLE FOR FOLIAGE GREEN 504 IS MIL-C-44436, ROLL #3729 (THE FOLIAGE

GREEN 502 AREA OF THE PATTERN), AND REFERENCED FOR SHADE ONLY.

INTERIM CHANGES TO MIL-C-3735E:

PAGE 4, PARAGRAPH 2.2 OTHER PUBLICATIONS. ADD THE FOLLOWING BELOW "METHOD NO. 8

COLORFASTNESS TO CROCKING: AATCC CROCKOMETER METHOD" "AATCC 20 - FIBER ANALYSIS:

QUALITATIVE"

PAGE 4, PARA. 3.3.3.1, FIBER.: DELETE IN ITS ENTIRETY AND SUBSTITUTE THE FOLLOWING:

"3.3.3.1 ARAMID FIBER BLEND. THE BLEND SHALL CONSIST OF 92 PERCENT META-ARAMID FIBER, 5 PERCENT PARA-ARAMID FIBER AND 3 PERCENT CONDUCTIVE FIBER. THE ARAMID FIBERS

SHALL HAVE A NOMINAL DENIER OF 1.5 TO 1.7 DENIER PER FILAMENT, A STAPLE LENGTH OF 1-

1/2 TO 2 INCHES, AND SHALL NOT CHAR AT A TEMPERATURE LESS THAN 675 DEG. F.. THE

CONDUCTIVE FIBER SHALL BE A NYLON SHEATHED CARBON CORE FIBER AND SHALL BE 3

DENIER PER FILAMENT AND 1/1/2 INCHES TO 2 INCHES IN STAPLE LENGTH (SEE 6.4)."

PAGE 5, PARAGRAPH 3.4, LINE 3, AFTER "(SEE 6.6)" ADD "OR FOLIAGE GREEN 504".

PAGE 10, PARAGRAPH 3.13, PH., LINE 2: AFTER "8.0" DELETE "AND".

PAGE 10, PARAGRAPH 3.13, PH., LINE 3: AFTER "8.5" ADD "AND FOR THE TYPE IV CUFFS AND

CLOTH SHALL NOT BE LESS THAN 5.0 NOR MORE THAN 8.0".

PAGE 12, TABLE IV. COMPONENT TESTS UNDER TEST METHOD COLUMN, LINE 6 DELETE "1600"

AND SUBSTITUTE "AATCC 20".

PAGE 23, PARAGRAPH 6.4: DELETE IN ITS ENTIRETY AND SUBSTITUTE THE FOLLOWING:

"6.4 TYPE IV FIBER BLEND. THE FINISHED CLOTH AND CUFF FIBER BLEND HAS BEEN

SUCCESSFULLY MANUFACTURED WITH YARNS PRODUCED FROM AN INTIMATE FIBER BLEND OF

92 PERCENT NOMEX, 5 PERCENT KEVLAR AND 3 PERCENT P-140. THE FIBER BLEND IS AVAILABLE

IN BALE FORM FROM E.I. DUPONT DE NEMOURS & CO. INC., WILMINGTON, DE. 19880."

ELECTROSTATIC DECAY TESTING IS NOT REQUIRED FOR THIS CUFF.

(ref. T0941 - 5/23/06)

MIL-DTL-10176L Cloth, Gabardine: Wool, Polyester and Wool dated 30-Mar-2018

SPONGING:

COLD WATER SPONGING IS REQUIRED. A PROPER ALCOHOL WETTING AGENT SHALL BE USED TO

INSURE SHRINKAGE IS ACCOMPLISHED AND WATER RESISTANT FINISH (when specified) IS NOT

RELEASED.

THE WATER REPELLANT TREATMENT (When Specified) SHALL BE APPLIED BEFORE THE SPONGING

OPERATION.

WHEN AIR FORCE SHADE 1605 IS SPECIFIED, THE CLOTH SHALL BE PIECE DYED.

ADDITIONAL INFO FOR MIL-P-15011: NO ADDITIONAL INFORMATION FOLLOWS.

INTERIM CHANGES TO A-A-55126B,

THE FOLLOWING CHANGES ARE FOR ALL CURRENT, PENDING AND FUTURE PROCUREMENTS OF

THE SUBJECT DOCUMENT UNTIL SUCH TIME AS THE DOCUMENT IS AMENDED OR REVISED.

PAGE 4. TABLE I, PHYSICAL REQUIREMENTS, CHARACTERISTIC, SHEAR STRENGTH,DELETE

LBS/SQ INCH (MIN), ADD SHEAR STRENGTH, LBS/2 SQ INCH (MIN).

PAGE 5 TABLE II, PHYSICAL REQUIREMENTS; CHARACTERISTIC, LENGTH

DIMENSIONAL STABILITY, % (MAX); LOOP, ALL CLASSES DELETE .0; ADD ALL CLASSES 4.0.

PAGE 7, Paragraph 3.10.2, Change the following title of paragraph from: "Fray resistance of Universal Camouflage Shades" and replace with "Fray resistance of Camouflage Prints"

PAGE 14, Paragraph 7.3.4 Change the following title of paragraph from: Fray resistance for Universal Camouflage Shades." and replace with "Fray resistance for Camouflage Prints."

INTERIM SPECIFICATION CHANGES TO MIL-C-21852F:

PAGE 1, CLASSIFICATION. PARA. 1.2, LINE 5 UNDER

"TYPE III", DELETE "2.0" AND SUBSTITUTE "1.8" AND

DELETE "68" AND SUBSTITUTE "61".

PARAGRAPH 3.4, TABLE I. PHYSICAL REQUIREMENTS.

UNDER "TYPE III", "WEIGHT" REQUIREMENT, DELETE

"2.0 (68)" AND SUBSTITUTE "1.8 (61)".

PAGE 13, PARA.4.5.4 SPECTRAL REFLECTANCE TEST.

LINE 4, DELETE "HALON" AND SUBSTITUTE

"POLYTETRAFLUOROETHYLENE (PTFE)".

(ref. T1036 - May 19, 2006)

A-A-52016A Cloth, Twill or Plain Weave, Polyester & Polyester Blend dated 19 Nov 2019 No Additional Information (ref. T1514)

ADDITIONAL INFORMATION FOR MIL-C-44192:

INTERIM CHANGES TO MIL-C-44192:

PAGE 4, PARA 3.2.4 AFTER "II" ADD "FOR DRESS

COATS AND TYPE "III" FOR ALL WEATHER COATS."

PAGE 11, PARA 30.4, DELETE AND SUBSTITUTE:

"30.4 CONTAINER CLOSURE. THE CONTAINER SHALL BE

CLOSED BY THE USE OF 3 INCH WIDE TAPE CONFORMING

TO TYPE II, CLASS 2 OF PPP-T-45. THE TAPE SHALL

BE CENTERED OVER EACH EXPOSED SEAM INCLUDING

THE DISPENSING DOOR SLITS AND EXTENDED OVER ALL

THE CORNERS AND EDGES WITH A MINIMUM OF 2 INCHES

ONTO THE ADJACENT BOX PANELS. THE MANUFACTURERS

JOINT AND THE EDGES AROUND THE BOTTOM OPENING

OF THE LID AFTER IT IS PLACED OVER THE

CONTAINER BOX BODY NEED NOT BE TAPED.".

NOTE: WHEN HANGER PACKS ARE SPECIFIED FOR ALL-

WEATHER COATS, COATS SHALL BE PACKAGED, MARKED

AND PALLETIZED IN ACCORDANCE WITH MIL-C-44192,

WITH FRONTS LAPPING AND BUTTONED.

THE FOLLOWING APPLIES:

TEN (10) COATS OF ONE CLASS AND SIZE SHALL BE

PACKED IN A TYPE I CONTAINER (HANGER PACK)

EXCEPT THAT THE DIMENSIONS OF THE CONTAINER

SHALL APPROXIMATE 24 X 21 INCHES AND THE DEPTH

OF THE CONTAINER SHALL BE 48 +0/-2 INCHES.

HANGER PACK SHIPPING CONTAINERS SHALL BE

MARKED A/C TO IDENTIFY THE LEVELS OF PACKAGING/

PACKING.

(Ref. T0806)

ADDITIONAL INFORMATION FOR MIL-C-44296:

INTERIM SPECIFICATION CHANGES TO MIL-C-44296A:

PAGE 1, PARAGRAPH 1.1, SCOPE., LINE 1: AFTER "AND" INSERT "STITCH-REINFORCED

NONWOVEN".

PAGE 1, PARAGRAPH 1.2, LINE 12: BETWEEN "TYPE X-CIRCULAR KNIT SUBSTRATE" AND "CLASS 1"

INSERT "TYPE X1- "STITCH-REINFORCED NONWOVEN".

PAGE 1, PARAGRAPH 1.2. CLASSIFICATION. BELOW "TYPE IX" ADD "TYPE X - CIRCULAR KNIT

SUBSTRATE"

PAGE 2, PARAGRAPH 2. APPLICABLE DOCUMENTS ADD FOLLOWING NEW PARAGRAPH: "2.1.3

OTHER PUBLICATIONS. THE FOLLOWING DOCUMENTS FORM A PART OF THIS DOCUMENT TO THE

EXTENT SPECIFIED HEREIN. UNLESS OTHERWISE SPECIFIED, THE ISSUES OF THE DOCUMENTS

WHICH ARE DOD ADOPTED SHALL BE THOSE LISTED IN THE ISSUE OF THE DODISS SPECIFIED IN

THE SOLICITATION. UNLESS OTHERWISE SPECIFIED, THE ISSUES OF THE DOCUMENTS NOT

LISTED IN THE DODISS SHALL BE THE ISSUES OF THE NONGOVERNMENT DOCUMENTS WHICH

ARE CURRENT ON THE DATE OF THE SOLICITATION.

AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS (AATCC) AATCC 20 - FIBER

ANALYSIS QUALITATIVE (APPLICATIONS FOR COPIES SHOULD BE ADDRESSED TO AMERICAN

ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS (AATCC), P.O. BOX 12215, TRIANGLE PARK, NC 27709-2215)"

PAGE 3, ADD THE FOLLOWING NEW PARAGRAPH: "3.1.2.10 TYPE X. TYPE X SHALL BE A CIRCULAR

KNIT. WHEN SPECIFIED (SEE 6.2), THE FACE SIDE SHALL BE NAPPED."

PAGE 3: AFTER PARAGRAPH 3.1.2.10,ADD THE FOLLOWING: "3.1.2.11 TYPE X1. TYPE X1 SHALL BE

STITCH- REINFORCED NONWOVEN WHEREBY A SERIES OF CHAINSTITCHING IS SEWN IN THE

MACHINE DIRECTION OF THE SUBSTRATE IN ORDER TO REINFORCE THE NONWOVEN

CONSTRUCTION."

PAGE 7, PARAGRAPH 3.4. PHYSICAL REQUIREMENTS. ADD THE FOLLOWING NEW TABLE AFTER

TABLE VII:

"TABLE VII. A PHYSICAL REQUIREMENTS FOR TYPE X

STYLE CLASS WEIGHT (INCLUDING BURSTING

ADHESIVE) STRENGTH

OZ/SQ/YD. LBS. (MIN.

MINIMUM MAXIMUM

A 1,2,3 OR 4 1.4 1.8 60

FIBER CONTENT

1/

1/ 100% NYLON OR POLYESTER."

PAGE 7,PARAGRAPH 3.4 PHYSICAL REQUIREMENTS.: AFTER TABLE"V111" ADD NEW TABLE 1X:

"TABLE 1X,PHYSICAL REQUIREMENTS FOR TYPE X1

BREAKING STRENGTH

WGT, OZ/YD2 LBS, (MIN) STITCHING

STYLE CLASS MIN MAX MACH X-MACH CONTENT REIN

FORCEMENT

A 1,2,3 1.0 1.8 10.0 1.0 1/ 2/

1/ 50 TO 100 PERCENT POLYESTER WITH REMAINING PERCENTAGE NYLON OR RAYON.

2/ STITCH REINFORCEMENT CONDUCTED WITH SINGLE MULTIFILAMENT THREAD USING

CHAINSTITCH STITCH TYPE WITH CHAINSTITCH LOOPS ON FUSIBLE SIDE TO PROTECT FROM

UNRAVELING."

PAGE 7, PARAGRAPH 3.4.1. BONDING STRENGTH.

- LINE 2, DELETE "(EXCEPT CLASS 5)" AND SUBSTITUTE "(EXCEPT TYPE IX WHEN USED AS

FUSIBLE SEAM TAPE AND CLASS 5)".

- LINES 7 AND 8, DELETE "OR SHEETING MATERIAL".

PAGE 9, PARA. 4.2.2.1, LINE 22, DELETE "30" AND SUBSTITUTE "20". LINE 24, DELETE "45" AND

SUBSTITUTE "30".

PAGE 11, TABLE VIII. END ITEM TESTS UNDER TEST METHOD COLUMN, LINES 2 AND 3 DELETE

"1600" AND SUBSTITUTE "AATCC 20".

PAGE 12, PARAGRAPH 4.3.1.1. BONDING STRENGTH PROCEDURE (INITIAL AND AFTER

LAUNDERING/DRY CLEANING). DELETE THE FIRST AND SECOND SENTENCES IN THEIR ENTIRETY

AND SUBSTITUTE: "CUT A 12 INCH WARP BY 11 INCH FILLING SAMPLE FROM BOTH THE

OUTERSHELL AND FUSIBLE MATERIALS SPECIFIED FOR CONTRACT USE (SEE 6.5)."

PAGE 15: AT THE END OF PARAGRAPH 6.1.1,ADD THE FOLLOWING:

" E. STITCH REINFORCED NONWOVEN TYPE X1 OFFERS HIGH DEGREE STRENGTH/STABILIZATION FOR TAPE AND STAY APPLICATION FOR LARGE OR SMALL PART FUSIBLES AND IS INTENDED TO

PROVIDE VERTICAL STABILITY AND ABRASION RESISTANCE."

PAGE 16, PARAGRAPH 6.5. BONDING STRENGTH DISPUTE PROCEDURE. INSERT THE FOLLOWING

BETWEEN THE FIRST AND SECOND SENTENCES: "IN SOME CASES, OUTERSHELL SAMPLES

REPRESENTATIVE OF SEPARATE PRODUCTION LOTS MAY BE USED TO DETERMINE IF DIFFERENT

FINISHES MAY AFFECT BONDING STRENGTH."

(ref. T0998 - 5/23/06)

FED-STD-191A THE FEDERAL STANDARD FOR

. TEXTILE TEST METHODS.

. 20 JULY 78.

TEST METHOD 5781:

OPACITY PF TEXTILE MATERIALS TO LIGHT OF

VISIBLE WAVELENGTHS.

TEST METHOD 5874:

TEMPERATURE, LOW; EFFECT ON COATED CLOTH

TEST METHOD 5972:

STRENGTH OF COATING; WATER RESISTANCE METHOD

EACH BUNDLE OF LACES CONSTITUTES A UNIT PACK,

AND SHALL BE TAGGED WITH THE INFORMATION RE-

QUIRED BY MIL-STD-129 FOR THE UNIT PACK.

ITEMS PACKED AS SPECIFIED SHALL BE PALLETIZED ON A 4-WAY ENTRY PALLET IN

ACCORDANCE WITH LOAD TYPE IA OF MIL-HDBK-774, EACH PREPARED LOAD SHALL

BE BONDED WITH HORIZONTAL, PRIMARY AND SECONDARY STRAPS (BONDING METHODS

C & D) OR FILM BONDING METHODS F OR G. PALLET PATTERN SHALL BE IN

ACCORDANCE WITH THE APPENDIX OF MIL-HDBK-774. THE PALLET SHALL BE

4-WAY, TYPE I, CLASS 1, STYLE 1, SIZE A, WOOD GROUP I, II, III OR IV OF

MIL-P-15011, OR, 4-WAY, TYPE IV, V OR VIII, CLASS 1, STYLE A, SIZE 2,

WOOD GROUP I, II, III OR IV, GRADE A OF NN-P-71.

IF THE CONTAINER IS OF A SIZE WHICH DOES NOT CONFORM TO ANY OF THE

PATTERNS SPECIFIED IN MIL-HDBK-774, THE PALLET PATTERN USED SHALL BE

APPROVED BY THE CONTRACTING OFFICER. EACH PALLET LOAD SHALL

CONTAIN THE SAME NUMBER OF CARTONS.

MIL-STD-129R w/CHANGE 2 - DEPARTMENT OF DEFENSE STANDARD PRACTICE MILITARY

MARKING FOR SHIPMENT AND STORAGE

DATED: 27 SEPTEMBER 2019

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE

MATERIAL) SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA TROOP

SUPPORT C&T ITEMS, REGARDLESS OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING CLOTHING, IT

MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS OF C&T ITEMS, THE

PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER TO BE LOADED FOR EACH

SHIPMENT. THE WORDS "PACKING LIST HERE" SHALL BE STENCILED, NOT HAND LETTERED, ON

THE CONTAINER.

MIL-STD-147E w/CHANGE 2

27 JUNE 2019

DEPARTMENT OF DEFENSE

STANDARD PRACTICE

PALLETIZED UNIT LOADS

JACKET, MAN'S: LIGHTWEIGHT WITH REMOVABLE LINER

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS

(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF

TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE

MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT

INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

WOMEN’S JACKET TECH DATA

MIL-DTL-8251A Jacket, Woman's: Lightweight with Removable Liner dated 11 SEP 2019

No information follows

DELETE CURRENT "BARCODE LABEL/TAG" REQUIREMENTS AND SUBSTITUTE THE FOLLOWING:

LABEL TAG: EACH ITEM SHALL BE INDIVIDUALLY BAR-CODED WITH A PAPER TAG FOR

PERSONAL CLOTHING ITEMS. THE PAPER USED FOR THE TAGS SHALL BE STANDARD BLEACHED

SULFATE HAVING A BASIS WEIGHT OF 100 POUNDS WITH A SMOOTH FINISH TO ACCEPT

THERMAL TRANSFER AND DIRECT PRINTING. THE TAGS SHALL HAVE A HOLE AND SHALL BE

ATTACHED TO EACH ITEM BY A FASTENER, CLEARLY LEGIBLE AND READABLE BY SCANNER.

THE BAR CODING ELEMENT SHALL BE A 13 DIGIT

NATIONAL STOCK NUMBER (NSN). THERE SHALL BE A 12 DIGIT UNIVERSAL PRODUCT CODE (UPC)

ASSIGNED FOR ALL NSNS BY THE GOVERNMENT. THE INITIAL "UPC" MUST APPEAR BENEATH

THE CODE. THE BAR CODES FOR NSN AND UPC SHALL BE A MEDIUM TO HIGH DENSITY AND

SHALL BE LOCATED SO THAT THEY ARE COMPLETELY VISIBLE ON THE ITEM WHEN IT IS FOLDED AND PACKAGED AS SPECIFIED. THE LABEL'S LOCATION SHALL CAUSE NO DAMAGE TO THE ITEM.

NOTE: UNIVERSAL PRODUCT CODE INFORMATION THE GOVERMENT ASSIGNED UNIVERSAL

PRODUCT CODE (UPC) MUST BE PLACED ON ALL SHIPPING CARTONS ON WHICH THE NSN

APPEARS.

THE FOLLOWING DEFECTS APPLY FOR BARCODE LABELS/TAGS:

BAR CODE OMITTED OR NOT READABLE BY SCANNER

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

HUMAN-READABLE INTERPRETATION (HRI) OMITTED OR ILLEGIBLE

NOT VISIBLE ON FOLDED, PACKAGED ITEM CAUSES DAMAGE TO THE ITEM

NOTE: IF THE END ITEM IS PLACED IN A PLASTIC BAG - USE TYPE VII (PRESSURE SENSTIVE

LABEL) OF MIL-DTL-32075.

IF THE END ITEM IS TIED IN A BUNDLE OR LEFT AS AN INDIVIDUAL ITEM, USE TYPE VIII (TAG, PAPER) OF MIL-DTL-32075.

PACKAGING:

LARGE QUANTITIES SHOULD BE SHIPPED IN THE STANDARD UNIT OF PACK (12 UNITS) CITED IN THE END ITEM SPECIFICATION - HANGER PACK. ALL REQUISITIONS FOR FULL UNITS OF PACK ARE REQUIRED TO BE HANGER PACKED. WHEN SHIPPING LESS THAN FULL UNITS OF PACK, THE

CONTRACTOR IS ALLOWED TO SHIP ACCORDING TO BEST COMMERCIAL PRACTICE.

ADDITIONAL INFORMATION FOR A-A-50083:

ADD THE FOLLOWING INTERIM CHANGES:

PAGE 1, PARA. 1.2, DELETE SECOND SENTENCE ENTIRELY, AND SUBSTITUTE "THE THICKNESS OF

THE MATERIAL SHALL BE 0.0010 TO 0.0090 INCHES IN ACCORDANCE WITH L-P-378."

(ref. T0894 - 5/23/06)

INTERIM CHANGES TO A-A-52094:

NO CHANGES

INTERIM STANDARD SAMPLE FOR FOLIAGE GRFEEN 504

IDENTIFIED AS ROLL #3721 (THE FOLIAGE GREEN 502

AREA OF THE PATTERN CLOTH MIL-C-44436), AND REFERENCED

FOR SHADE ONLY. THIS STANDARD IS TEMPORARY UNTIL FURTHER

NOTICE.

ADDITIONAL INFORMATION FOR NN-P-71:

NO ADDITIONAL INFORMATION FOLLOWS..

"MIL-DTL-32075: LABEL FOR CLOTHING, EQUIPAGE,

AND TENTAGE, GENERAL USE REPLACES DDD-L-20

(Ref. T0451 - June 19, 2007)

INTERIM SPECIFICATION CHANGES TO MIL-DTL-32075:

PAGE 6, TABLE I, "PHYSICAL REQUIREMENTS OF THE

TYPE VI FINISHED LABEL." UNDER "TEARING

STRENGTH" DELETE: "(LB.) MINIMUM" AND

SUBSTITUTE: "(GNS) MINIMUM."

PAGE 12, PARA 3.3.2.17, AFTER "NSN" ADD

"AND THE UNIVERSAL PRODUCT CODE (UPC)

SUPPLIED BY THE GOVERNMENT, FOR ALL NSNs."

ADDITIONAL INFORMATION FOR MIL-I-45208:

NOTE: MIL-I-45208 HAS BEEN CANCELLED AND REPLACED BY THE…