SOW Hydrostatic Test Stand.pdf

STATEMENT OF WORK

1. Title

Replacement of the existing Hydrostatic Test Stand prepared 14 June 2024 for the DLA Land and Maritime Engineering & Technical Support Directorate Product Test Center Division, Mechanical Lab, VTM.

2. Introduction

The MPTC Product Test Center needs to acquire a new Hydrostatic Test Stand capable of generating 20,000 pounds per square inch (PSI) of pressure to conduct Proof, Leakage, Burst and

Electrical Conductivity testing of DLA’s Customer supplied products such as hoses and valves in support of the Warfighter efforts. This Test Stand supplies the containment and pressure holding controls necessary to capture immediate pressure rupture and timed collection data.

3. Background

Using the buildings facility provided water and compressed air the current Hydraulic Test

Stand provides limited pressure testing through analog gaging. However, our Test Stand has exceeded its service life, analog gages have gotten damaged due to their mechanical sensitivity from annual shipping for calibration, hard water minerals over the decades of use have degraded the unit’s ability to hold pressure and corroded our test hoses and fittings. All these factors have put the MPTC at risk of loss of capabilities in pressure testing.

Replacing the aging unit with a new one with state-of-the-art digital gaging will increase our accuracy in capturing data, increase our quality in pressure holding capabilities and increase associate’s safety with a new containment system, hoses and fittings.

4. Scope

In accordance with current SAE, Military and Industry Standards the Hydrostatic Test Stand should be made to meet or exceed design specifications for high pressure vessel testing for commercial and military applications. It should be stand alone with complementing hoses and fittings required for use. The supplier of the Hydrostatic Test Stand will be required to install and make ready for use in operations of all aspects of the Test Stand.

The result of acquiring a new Hydrostatic Test Stand will give the MPTC the equipment and tools necessary to conduct high and low pressure testing to better suit the quality testing requirements and the needs of the Warfighter.

5. Applicable Directive

None

6. Performance Requirements

1. Major Task: Manufacture a Hydrostatic Test Stand capable of generating pressures between 0-20,000 psi.

2. Major Task: Schedule and deliver Hydrostatic Test Stand to the DLA 3990 East Broad

Street Columbus, OH 43213 Product Test Center. Dependent upon size of unit, delivery to

Building 17 may be required to log delivery, Bill of Lading etc.

3. Major Task: Provide installation, setup, instructional manuals/materials and accessories.

4. Major Task: Perform operational or function checks necessary with MPTC Associates to verify system.

5. Major: Schedule training with MPTC.

7. Deliverables

a. Gage Calibration Certifications

b. Pressure Tank Certifications

8. Contractor Information: please list what type of Experience, Past Performance, Certifications, and/or Scheduling Needs that are required from the Contractor

a. Contractor will coordinate with MPTC on delivery, setup and training dates.

9. Place of Performance

3990 East Broad Street

Columbus, OH 43213

Building 9, Section 2

10. Travel (if applicable)

Contractor is responsible for travel to Place of Performance listed in section 9.

11. Invoicing

Payment of invoices will be accomplished by payment through the Defense Finance and

Accounting Service. Invoices will be submitted to the Wide Area Workflow system in accordance with DFARS 252.232-7003 Electronic Submission of Payment Requests and

Receiving Reports and DFARS 252.232-7006 Wide Area Workflow Payment

Instructions within 10 workdays after the conclusion of each training session.

11. WAWF Acceptance DODAAC#

TM Lab is SL0702.

11. Point of Contacts

The Government Contract Officer:

TBD

The Government Contract Officer Representative (COR):

Kyle Palmer (kyle.palmer@dla.mil)

614-692-8860

DLA Land and Maritime Product Test Center (Engineering Tech):

Lee Shull (lee.shull@dla.mil)

614-692-8107

DLA Land and Maritime VTM (Supervisor):

Jeff Fleeger (Jeffery.Fleeger@dla.mil)

614-692-4954

The Government Technical Representative/Project Manager:

Name: Bret Dement

Phone Number: (614) 692-8437

Email Address: bret.dement@dla.mil mailto:lee.shull@dla.mil mailto:Jeffery.Fleeger@dla.mil