Updated_Robins_PWS.pdf

Table of Contents

0. PERFORMANCE WORK STATEMENT

1. REMOVAL

1.1 PRE-REMOVAL

1.1.1 PERMIT/SPECIAL REQUIREMENTS

1.1.2 SHIPPING DOCUMENTATION

1.1.3 NOTIFICATIONS

1.1.4 TRAILER SECURITY, PADLOCKS

1.1.5 HOURS OF OPERATION

1.1.6 PUBLIC AFFAIRS COORDINATION

1.1.7 NAVY and MARINE INSTALLATION ACCESS SECURITY

1.1.8 ENVIRONMENTAL MANAGEMENT SYSTEM

1.2 REMOVAL

1.2.1 SPILL RESPONSIBILITY

1.2.2 SEGREGATION OF HAZARDOUS WASTE

1.2.3 STATEMENT ON CONTAINERS

1.2.4 GOVERNMENT EQUIPMENT & PERSONNEL

1.2.5 TREATMENT OF HAZARDOUS WASTE ON GOVERNMENT

FACILITY

1.2.6 LOADING

1.2.7 WEIGHING OF ITEMS

1.2.7.1 TASK ORDER ADJUSTMENTS

1.2.8 DEFINITIONS, BULK & CONTAINERIZED WASTE

1.2.8.1 BULK WASTE

1.2.8.2 CONTAINERIZED WASTE

1.2.9 BULK LIQUID PUMPING

1.2.10 BULKING & CONSOLIDATION

1.2.11 EXPEDITED SERVICES

1.2.12 PACKAGING FOR COMPLIANCE

1.2.13 PACKAGING FOR CONVENIENCE

1.3 POST REMOVAL

1.3.1 RETURN OF SHIPPING DOCUMENTATION

2. DISPOSAL/RECYCLING

2.1 RCRA/NON-RCRA ITEMS

2.1.1 TSCA/RCRA/NON-RCRA/STATE/NON-STATE REGULATED ITEMS

2.1.2 CERTIFICATES OF DISPOSAL, DESTRUCTION, & RECYCLING

2.1.3 DETAILED ANALYSIS

2.1.4 PROCESS AUTHORIZATION PLAN FOR ALTERNATE

DOCUMENTATION OPTION FOR FUELS BLENDING & RECYCLING OF

ANTIFREEZE, USED OIL, BATTERIES, & LAMPS

2.1.5 RESERVED

2.1.6 EMPTY CONTAINERS

2.2 DISPOSAL OF PCB, PCB-RELATED WASTE

2.3 COMPRESSED GAS CYLINDERS

2.3.1 EVALUATION/IDENTIFICATION OF CYLINDERS

2.3.2 ANALYSIS TO IDENTIFY CYLINDER CONTENTS

2.3.3 RECONTAINERIZATION/REPLACEMENT OF VALVES

2.3.4 SURCHARGE FOR ZONE “A” POISON GASES

2.4 RECYCLING

2.4.1 RECYCLE/RECOVERY/RE-USE/RECLAIM

2.4.2 COMMODITY SPECIFIC RECYCLING REQUIREMENTS

2.5 DEMILITARIZATION

2.5.1 OTHER MILITARY ITEMS

2.5.2 DEMIL ELECTRON TUBES

2.5.3 ELECTROPLATING RELATED WASTES

3. SPECIAL SERVICES

3.1 PROVIDE CONTAINERS FOR CONVENIENCE

3.2 TANK & WASH RACK CLEANING

3.3 PERFORM ANALYSIS

3.4 PREPARE WASTE PROFILE SHEET

3.5 IDENTIFY UNKNOWN WASTE STREAMS & PREPARE WASTE

PROFILE SHEETS – TWO STEP METHOD

3.6 PROVIDE ROLLOFF STORAGE CONTAINERS & RENTAL CHARGES

3.6.1 CONTAINMENT/FRAC TANK

3.6.2 VACUUM BOX

3.6.3 RELOCATE/EMPTY ROLLOFF(S) AND/OR VACUUM BOXES

WITHIN INSTALLATION

3.7 LAB PACKING SERVICES

3.8 MANAGEMENT SERVICES AT ROBINS AFB

3.9 BULK NON-RCRA WASTEWATER MANAGEMENT

3.10 SUPER VACUUM TRUCK WITH DUMP FUNCTION AND OPERATOR

3.11 VACUUM TRUCK WITH DUMP FUNCTION AND OPERATOR

3.12 RCRA REGULATED BLAST MEDIA CONTAINING NATURALLY

OCCURING RADIOACTIVE MATERIAL (NORM)

3.13 RESERVED

3.14 INDUSTRIAL WASTEWATER TREATMENT PLANT (IWTP) SLUDGE

3.15 RESERVED

3.16 ROBINS AFB BULK LIQUID TRANSPORT

3.17 MILK RUN SERVICES

3.18 PROVIDE STORM DRAIN FILTERS

4. ACCEPTABLE PERFORMANCE LEVELS

4.1 ACCEPTABLE PERFORMANCE LEVEL TABLE

5. USE OF FACILITIES AND TRANSPORTERS

5.1 QUALIFIED FACILITIES

5.2 QUALIFIED TRANSPORTERS

5.3 ADDITIONAL TSDFS AND TRANSPORTERS

6. ADDITIONAL REQUIREMENTS

6.1 INDEMNIFICATION

6.2 REPORTING REQUIREMENTS

6.2.2 CONTRACTOR ACCESS TO DLA DISPOSITION SERVICES

DISTRIBUTION STANDARD SYSTEM/ULTIMATE DISPOSAL (DSS/UD), PHASE

II ONLY

6.3 PACKING, MARKING AND LABELING

6.4 PLACES OF GOVERNMENT INSPECTION

6.5 CONTRACTOR REPRESENTATIVE

6.6 INCIDENTAL FEES

6.7 MANPOWER REPORTING REQUIREMENTS

7. PERIOD OF PERFORMANCE- INCLUDING DISPOSAL AND REMOVAL

8. DOCUMENTATION REQUIREMENTS, DLA DISPOSITION SERVICES ACCEPTANCE,

INVOICING AND TRACKING

8.1 SUBMISSION OF DOCUMENTATION TO FACILITATE ACCEPTANCE FOR

PAYMENT

8.1.1 ACCEPTANCE AND INVOICING

8.2 POST-PAYMENT TRACKING

8.3 REMEDIES FOR NON-COMPLIANCE

0. PERFORMANCE WORK STATEMENT

a. This contract is referred to as the Robins AFB HW Disposal Contract. Work will consist of the removal and disposal of government generated hazardous and non-hazardous wastes located on military various installations.

b. This contract consists of one (1) 30-month Base Period, followed by one (1) 30-month Option Period.

c. Pricing for containerized waste will largely be based upon container sizes and the assigned disposal profile, rather than pricing on a per pound basis. The exception is bulk wastes as defined in paragraph 1.2.8.1 and containerized waste with the suffix C7.

d. This contract is a firm-fixed price indefinite delivery/indefinite quantity (IDIQ) contract written as a performance based contract and allows the Contracting Officer to make monetary deductions and/or a negative mark on the Contractor’s Past Performance when an Acceptable Performance Level (APL) is not met (see I.118 and APL attachment).

e. Some CLINs ordered under this contract require the Contractor to provide Certificates of Destruction or Disposal (CD), e.g., certain Demilitarization items and PCB-related wastes. The Contractor is cautioned to closely read all CLIN descriptions where such requirements are indicated. Unless explicitly required and written into this contract, only those CLINs requiring CDs, as described in the Bid Schedule, will require that the Contractor provide a CD.

f. Within 14 calendar days after Award, the Contractor shall provide DLA Disposition Services with a list referencing all intended interim and final disposal/recycle facilities by EPA ID number (where applicable) for every Base CLIN listed in the Bid Schedule of this contract; see Facility- CLIN Assignment Sheet. The purpose for this is to allow the Government to assign in DSS those facilities that will or might receive those CLINs for treatment, storage, and disposal. If this is not done, Task Orders (TO) cannot be processed in DSS.

g. The Government agrees that all items placed on a Task Order (TO) on this contract will be accompanied by documentation and markings that comply with all applicable local, state, and federal laws and regulations relating to the generation, storage and transportation of waste.

h. The Contractor agrees to provide all services necessary for the transportation, final treatment, disposal, and/or recycling of the items listed in the schedule in accordance with (IAW) all local, state, and federal laws and regulations, and the terms and conditions of this contract. These services shall include all necessary personnel, including applicable Subcontractors, labor, transportation, equipment, and the compilation and submission of all documentation required by this contract. All items, regardless of the condition, are being discarded by the Government and will require recycling or disposal as identified via the ordered Contract Line Item Number

(CLIN).

i. Generators are responsible for ensuring their containerized wastes sent for disposal via this contract are in Department of Transportation (DOT) shippable packaging.

j. The six- character disposal CLIN consists of two parts. The term “Base CLIN” refers to the first four characters of the CLIN. The Base CLIN represents the waste description according to the waste profile for a particular wastestream. The term “CLIN Suffix” refers to the last two characters of the CLIN. The CLIN Suffix designates the unit of measure for purposes of tracking and Contractor payment. Example: Base CLIN “CS01” represents Corrosive Acids, Inorganic other than HF and HNO3, <50% in Water, and the CLIN Suffix “C4” designates the unit of issue as a 55-Gallon Container. Accordingly, one (1) 55-gallon drum of this waste would be represented by ordering one (1) Each of CLIN CS01C4. See Profile-Based CLIN Guidelines and Master CLIN Schedule at http://www.dla.mil/DispositionServices/Offers/Disposal/HazardousWaste/HazWasteDisposal.as px for more details.

1. REMOVAL

The requirements for removal of wastes under this contract are divided into three main phases:

Pre-Removal (1.1), Removal (1.2), and Post-Removal (1.3). The Contractor and their Subcontractors must perform at all times in a prudent, conscientious, safe, and professional manner. The Contractor shall ensure that its agents, employees, and Subcontractors involved in handling and packaging the hazardous waste be trained for the level of expertise required for the proper performance of the task and, in particular, in the areas of chemical incompatibility, general first aid procedures, and spills. The Contractor shall provide all Material Handling Equipment (MHE) and Personal Protective Equipment (PPE), unless otherwise stated. The MHE and PPE must be appropriate to safely handle the hazardous waste. While operating on a Department of Defense (DOD) facility, the Contractor may be required to use forklifts.

Contractor-operated forklifts must meet specifications listed in the applicable permit. The Contractor agrees that all personnel and equipment used in the performance of this contract are subject to safety inspections by Government personnel while on federal property.

1.1 PRE-REMOVAL

a.The Contractor is encouraged to perform a pre-removal inspection of all containers at least ten days prior to the day of the off-site shipment. Any discrepancies associated with the marking, and/or labeling of containers, shall be reported to the COR for resolution.

b. CLIN discrepancies on a Task Order noted during the pre-removal inspection and/or during removal by the Contractor on CLINs already on the Bid Schedule will be address immediately via the COR and the Generator. If The COR and the Generator concur with the CLIN change, a Task Order Modification will be submitted to the Contracting Officer. Other Task Order inconsistencies, such as quantity changes, noun descriptions, adding/deleting lines, task orders extensions, etc. will be address similarly.

http://www.dla.mil/DispositionServices/Offers/Disposal/HazardousWaste/HazWasteDisposal.aspx

c. If the Contractor asserts that an inappropriate CLIN has been assigned, and a new CLIN needs to be added to the Contract, the burden of proof lies with the Contractor. The waste in question shall not be treated or disposed of until the Government has made a final determination. The Contractor must provide documentation electronically, which supports the assertion through independently acquired laboratory analysis at the Contractor’s expense, TSDF fingerprinting results, Safety Data Sheet, and/or other written supporting documentation. If the waste has been shipped inadvertently, the Contractor has sixty calendars days from the date the first transporter picked up the waste to provide said documents to the COR and the CO. After receipt of the supporting documentation by The Hazardous Disposal Branch/J331, the Government will review said documents and within 21 calendar days will determine if reassigning a new CLIN is applicable.

1.1.1 PERMIT/SPECIAL REQUIREMENTS

a. The Contractor shall, without additional expense to the Government, be responsible for paying all fees, preparing or obtaining any necessary licenses, permits, notifications, waste profiles, or reports, which result from a Contractor’s transportation, recycling, or disposal decision. This includes acquiring any required permits or registrations necessary to operate on any installation listed in this contract and completing the Notification of Regulated Waste Activity form for the Generator(s) of hazardous waste to sign and file with the applicable state regulators for waste disposal. This includes signing (on behalf of the Government) waste profiles requested by Treatment, Storage, and Disposal Facilities (TSDF). All Contractor-signed waste profile sheets shall be written for the actual wastestream using the Generator’s profile for backup documentation. All Generator forms or other means of notifications including correspondence with federal or state agencies on behalf of a Generator must be coordinated with and concurred with by the affected Generator prior to submission to any federal or state agency. A copy of all forms and relevant documentation, including correspondence shall be provided to the COR.

b. The Contractor may be required to attend special training, seminars, instructions, classes, safety orientations, etc., provided by the Government or to provide information to perform work or gain access to the installation. Example: pass and ID requirements, antiterrorist training, Environmental Management System (EMS) policies, and/or forklift training.

c. The Contractor and any Sub-contractor(s) shall use only the facilities and transporters listed in the DLA Disposition Services Qualified Facilities List (QFL) and Qualified Transporters List (QTL), see Section 5.

d. Any import or export shipment outside the United States must comply with all international agreements and all applicable foreign laws. If the Contractor will be exporting directly from the DOD activity, the Contractor is required to provide a current copy of the Acknowledgment(s) of Consent to the Contracting Officer Representative (COR) with the shipping documentation IAW Section 1.1.2.

e. The Contractor may not ship waste outside of the United States to circumvent Environmental Protection Agency (EPA) Land Disposal Restrictions (LDR) unless domestic treatment capability does not exist or domestic facilities are unable to meet EPA LDR requirements within the United States (e.g., Lithium batteries). High level mercury (>260 mg/kg) will not be exported outside the United States.

1.1.2 SHIPPING/DISPOSAL DOCUMENTATION

a. All references to manifests in this provision refer to the appropriate shipping papers.

Prior to removal from a site identified as a pickup point in this contract, completed copies of all manifests and LDR notifications shall be furnished to the Disposition Services Field Activity coordinating the waste disposal. All documentation shall be clearly marked with the name of the servicing Disposition Services Field Activity in addition to the Generator, contract, and TO number, as applicable. Emergency response information and 24-hour emergency phone numbers shall be listed on the manifest. If blocks for emergency information are not provided, this information shall be placed in the upper right-hand corner of each document.

The Contractor shall provide the COR or the Contracting Officer Technical Representative (COTR) with a copy of the completed form(s) for review by the appropriate Government official at least five (5) business days prior to removal. Notifications for expedited orders shall be performed IAW timeframes as listed in Section 1.2.11.

b. Mock EPA ID numbers created by DLA Disposition Services for use at non-RCRA TSDFs must be entered on all applicable shipping documentation such as non-hazardous waste manifests and bills of lading (BOL). The same mock EPA ID number must be used on DLA Disposition Services Form 2505, Manifest Tracking Log.

1.1.3 NOTIFICATIONS

a. Except as may otherwise be specified herein, the Contractor shall notify the COR for each location, at least five (5) business days BEFORE attempting site visits, analyses, or pickups.

For Georgia Army National Guard (Ga ARNG) locations, the five (5) business days shall not include weekends, holidays, or Mondays.

(1) In addition to the notification above for pickups, the Contractor shall provide the name of the driver, the driver’s Commercial Driver License (CDL) number and its expiration date, to the COR or other Government representative at least 24 hours prior to removal. The Contractor may also opt to provide a list of approved, multiple drivers designated for pickups under this specific contract to the COR or other Government representative prior to any attempted removals. If this option is elected and the list is approved by the Government and maintained by the Contractor, the 24-hour notification requirement is mute for the remainder of the contract unless otherwise modified.

(2) If a driver, other than the one specified 24 hours in advance for the specific TO; or, one whose name does not appear on the optional list of approved, multiple drivers arrive for pickup, the COR or other designated Government representative will verify the personnel switch with the Contractor before the pickup commences. This may require a written notice or fax from the Contractor.

b. For Task Orders (TO) containing Expedited Removals, Services, or Performance CLINs, the Contractor shall notify the COR or other Government representative for each location in the following timeframes BEFORE attempting site visits, analyses, or pickups: 5 day expedites – at least 2 calendar days; and 4 days or less expedites – at least 1 calendar day. In addition, the Contractor is still required to provide the information identified in subparagraph (1) above at least 24 hours prior to removal. If applicable, any removals ordered under a 24-hour or one business day expedited CLIN requires the Contractor to provide the information identified in subparagraph (1) above at least 4 hours prior to pickups if the Contractor elects to provide the identity of the driver for each specific TO. If the Contractor elects to provide the list of approved, multiple drivers designated for use under this contract, this expedited notification is not required.

All other terms and conditions stated in the Contract Instructions and Information section of this contract and within this section apply to any of the aforementioned Expedited Removals, Services, or Performance CLINs.

NOTE: Defense Biometric Identification System may be mandatory for access to some DOD facilities, see 1.1.7. If DBIDS is deployed, the 24-hour advance notification in Paragraph 1.1.3 is not required. At some Military Installations, it may be required to escort the Contractor and/or Sub-Contractors to and from the place of duty. This requirement is both, for safety and physical security purposes. Contractors and/or it agents will not be allow to wander off from the work site. Contractors and/or it agents are required to remain on /at designated work areas.

1.1.4 TRAILER SECURITY, PADLOCKS

a. All Contractor trailers and tankers capable of being padlocked must be padlocked upon arrival at the pickup location. Failure to meet this requirement could result in the Government’s halting of the pickup. All trailers and tankers capable of being padlocked must also be padlocked again prior to departure of the pickup location(s). The driver shall provide the padlock and lock the trailer or tanker without assistance from the COR or other Government representative.

b. The COR or other Government representative has the right to request any identification and/or occupational endorsements from the driver beyond what is identified in additional specific sections in this contract and refuse commencement and/or completion of pickups if any unusual or suspicious actions occur. Any potential demurrage associated with the driver verification process and/or the unexpected halt or commencement of pickups will not be grounds for reimbursement by the Government.

1.1.5 HOURS OF OPERATION

The Contractor agrees that, for those portions of the services provided on a Government installation, the services will be provided during normal hours of operations for the installation.

The normal hours of operations for installations on this contract are Monday through Friday, 0700 – 1600 hours, unless otherwise indicated by the Government.

1.1.6 PUBLIC AFFAIRS COORDINATION

The Contractor shall refer all inquiries concerning this contract to the Contracting Officer (CO).

Under no circumstances shall any statement be released to the news media directly by the Contractor or any agents of the Contractor.

1.1.7 NAVY and MARINE INSTALLATION ACCESS SECURITY

a. Navy and Marine Corps installations now require that all Contractors and their representatives be enrolled in Defense Biometric Identification System (DBIDS) to gain access to these installations. DBIDS replaces the former Rapid Gate access system and also requires a security background check for all Contractors and their representatives.

b. For DBIDS enrollment information, go to: https://www.cnic.navy.mil/om/dbids.html.

1.1.8 ENVIRONMENTAL MANAGEMENT SYSTEM

DLA Disposition Services implemented EMS in accordance with ISO 14001:2004(E), DOD and DLA requirements at all DLA Disposition Services appropriate facilities. An EMS is an overall management system that includes organizational structure, planning activities, responsibilities, practices, procedures, processes and resources for developing, implementing, achieving, reviewing and maintaining the environmental policy of an organization. The DLA Disposition Services EMS is designed to ensure that all personnel, including contract personnel, whose work activities can cause real or potential significant environmental impact, are aware of how their work supports the EMS and are competent to perform their roles, responsibilities and authorities while supporting the DLA Disposition Services mission. The DLA Disposition Services EMS program is explained in agency Environmental Management System (EMS) Core Instruction.

Site supplements may detail information required by EMS at a local level such as local, state and host environmental regulations as well as local emergency procedures and operating procedures unique to the location. Site supplements also contain information concerning the local interaction between the DLA Disposition Services tenant appropriate facility and the DOD/DLA host facility EMS program. Contractors and their personnel are required to be aware that each DLA Disposition Services appropriate facility has an EMS and to be aware of EMS policies to perform work and/or gain access to an installation. Each DLA Disposition Services appropriate facility maintains EMS awareness posters that identify the DLA Disposition Services Environmental Management Representative (EMR) and Host facility EMR for specific guidance concerning an individual facilities’ EMS program. Contractors may request current copies of EMS information identified in this paragraph by contacting the local Contracting Officer's Representative (COR).

1.2 REMOVAL

1.2.1 SPILL RESPONSIBILITY

a. The Contractor and/or Sub-Contractor shall have a serviceable, compatible and operable spill kit(s) on-site to capture and contained the spill or released. The Contractor is solely responsible for cleanup and proper disposal of all spills or leaks during the performance of this contract that occur as a result of, or are attributed to, the actions of its agents, employees, or Sub- Contractors to the satisfaction of the Government and at no additional cost to the Government.

Hazardous waste spill cleanups that occur as a result of, or are attributed to, the actions of its agents, employees, or Sub-Contractors shall be removed off-site within 72-hours of the cleanup.

Under extenuating circumstances and with approval of the Host’ Environmental Office, hazardous waste spill cleanups may be allowed to move to a permitted Satellite Accumulation Area until it can be shipped off-site. The Contractor shall prepare a separate manifest for the spill cleanup removals.

b. The Contractor shall report all such spills or leaks, regardless of their quantity, to the COR (if not already present) and the CO immediately upon discovery. The Contractor shall adhere to https://www.cnic.navy.mil/om/dbids.html all Host or Installation spill reporting and clean-up requirements. A written follow-up report shall be submitted to the CO not later than 24 hours after the initial telephonic report. The written report shall be in narrative form and as a minimum include the following:

(1) Description of material spilled (including identity, quantity, manifest number, etc.).

(2) Whether quantity spilled is EPA/state reportable, and if so, whether it was reported.

(3) Exact time and location of spill, including a description of the area involved.

(4) Containment procedures initiated.

(5) Summary of any communications Contractor has with anyone other than the

CO.

(6) Description of clean-up procedures employed or to be employed at the site including disposal location of spill residue.

1.2.2 SEGREGATION OF HAZARDOUS WASTE

All items collected on this contract must be segregated according to the current EPA Hazardous Waste Compatibility Chart, and kept physically separate from any containers not associated with this contract until the initial TSDF is reached. The items must be so marked, that they are readily linked to this contract throughout this period. The Contractor may bring other waste onsite while conducting Milk Runs, or picking up waste at multiple locations, as long as the waste is listed on the current DO being picked up.

1.2.3 STATEMENT ON CONTAINERS

The Generator is responsible for ensuring their containers are DOT shippable, i.e., IAW current DOT regulations and standard TSDF acceptance. The Contractor is responsible for all repackaging costs associated with special container acceptance criteria at the TSDF.

1.2.4 GOVERNMENT EQUIPMENT & PERSONNEL

The Government shall not furnish any equipment or personnel to assist in the performance of this contract. Any such offers of assistance are unauthorized, and the Contractor shall not accept any such offers. The only exception is the use of Government-owned loading equipment (Section 1.2.6), and Government-owned scales (Section 1.2.7), and where applicable, management services.

1.2.5 TREATMENT OF HAZARDOUS WASTE ON GOVERNMENT FACILITIES

a. Treatment of hazardous waste (including solidification) on Government facilities is not permitted. Treatment is defined as any process which meets the definition of treatment as identified in 40 CFR 260.10 and/or the facility Permit.

b. The Contractor shall not drain and/or flush PCB items at Government facilities. Draining will be allowed only to prevent leaking and to meet DOT regulations.

c. Treatment, disposal, or release of gases, other than inert gases, to the atmosphere on Government premises is not permitted by this contract. The Contractor may perform gas extraction for other than inert gas cylinders at the pickup location using a self-contained apparatus. This apparatus shall emit no gas into the atmosphere, and purge the entire cylinder contents into a closed receiver for transport to a recycling or disposal site.

1.2.6 LOADING

a. The Contractor is responsible for loading, including furnishing all the equipment necessary for loading. The Government will not load at any location on any day in which the facility is closed unless otherwise specified. Where it is provided that the Government will load, the Government will make the initial placement of the item on conveyance(s) furnished by the Contractor and the initial placement on the Contractor's conveyance shall be as determined by the Government. Unless otherwise provided in this contract, the Government will not block, chock, brace, lash, band, or in any other manner, secure the cargo on such conveyance(s) furnished by the Contractor.

b. At Bldg. 359 Warner Robins AFB, GA only, the contractor shall use Government-owned loading equipment (forklift) to remove HW from Bldg. 359’s pallet racks for loading onto contractor conveyance. The following conditions apply:

(1) The Government will ensure that the forklift is maintained, safe to operate and available on the required performance date of the Task Order.

(2) The contractor shall obtain liability insurance coverage in the amounts currently covered by the contract (showing clear coverage of the contractor’s use of the Government handling equipment), or the current insurance company certifies that the contractor’s use and operation of said material handling equipment is specifically covered under the terms and conditions of existing policies. In addition, the contractor shall ensure that its employees are trained forklift operators and certified to operate the equipment at Bldg.

359.

(3) The contractor shall also indemnify, save and hold harmless the United States of America and any subdivision or agent thereof, from any injury, damage, or liability claimed as a result of the contractor’s use of the Government-Owned material handling equipment during the term of this contract.

(4) For Bldg. 359 only at Robins AFB GA, items for the entire Task Order shall be picked up on the same day.

c. CLIN 6393 will be ordered to compensate the Contractor by the hour for additional time delayed at a site after a period that would normally be allowed for the loading or unloading of a vehicle or for the Contractor to perform a service. Compensation is for the time delayed for a scheduled appointment, when the Government activities are the reason for the delay. If the Contractor arrives on site early without previous coordination with the Government, CLIN 6393 is not applicable. This charge is applicable when performing a service, where the

COR/Generator failed to be at the appointed place to allow the Contractor performed the service on a pre-scheduled appointment. Similarly, the Contractor shall be compensated for, if the Government did not notify the Contractor of a cancelled appointment; in such cases the Contractor shall be compensated for a minimum of four (4) hours. The Unit of issue is "EA", where 1 EA = 1 hour.

1.2.7 WEIGHING OF ITEMS

Government scales will be used when available, operable, and authorized by the Government.

The Contractor shall be responsible for determining the availability of Government scales. All scales used for purposes of this contract shall be calibrated IAW applicable regulations. The Government shall ensure that Government scales are operable and accurate through certification or demonstration. The Contractor shall ensure that non-Government scales are operable and accurate through certification or demonstration.

At the Government's option, the use of Government scales will be allowed at the following sites:

SITE EQUIPMENT AVAILABLE

Ft. Stewart, GA Bldg. 1157

Floor Scale (3,000 lbs Capacity)

DLA Disposition Services-Warner Robins

Truck Scale

Before loading, the Contractor is required to weigh the waste hauling vehicle, trailer, and/or rolloff/vacuum box, as applicable, to establish the empty (tare) weight of the rolloff box, dump truck, tanker truck, etc. This weight will be documented on a certified weight ticket and provided to the COR. An authorized Government representative will witness all weighing that occurs on site. After loading, the Contractor is required to weigh the waste hauling vehicle, trailer, and/or rolloff/vacuum box, as applicable, to establish the loaded (gross) weight of the conveyance. This weight will be documented on a certified weight ticket and provided to the COR. The actual (net) weight of the waste shall then be calculated by subtracting the tare weight from the gross weight. When onsite Government scales are available, weights must be agreed upon by both the Contractor and the Government before removal. When offsite commercial scales must be used, a certified weight ticket will be provided to the COR and shall be the basis for payment to the Contractor.

1.2.7.1 TASK ORDER ADJUSTMENTS

All task order weights are estimated amounts. The contractor can expect that the task order weights will be required to be adjusted upward or downward as removals take place and the actual pounds being removed are measured. Therefore, the Government has the unilateral right to increase the task order weight in those instances where the Government has underestimated the amount of weight that is required to be removed so the contractor can continue performance. The Government has the unilateral right to decrease the task order weight in those instances where the Government has overestimated the amount of weight that is required to be removed. In instances of decreasing weight, these decreases are not subject to FAR 52.212-4, termination for convenience coverage. In addition, it is agreed that it is acceptable for the Government to issue task order modification (i.e. quantity changes, noun descriptions, HIN changes, adding/deleting lines, extending task order end dates, etc.) unilaterally. The contractor will be paid for the actual items and quantities removed per the awarded contract price schedule. If upon receipt of a unilateral task order modification, the contractor does not agree with the change or changes, the contractor reserves the right to seek resolution with the Contracting Officer. These modifications are only against task orders. No changes are made to the terms and conditions of the contract.

1.2.8 DEFINITIONS, BULK & CONTAINERIZED WASTE

1.2.8.1 BULK WASTE

a. The term bulk waste refers to waste that is typically removed via rolloff boxes, vacuum or sludge boxes, dump trucks, tank trucks, vacuum trucks, pump trucks, and trucks with vacuum-loaded or pump-loaded tanker trailers. Pumpable liquid wastes that are removed via totes, also known as portable tanks and Intermediate Bulk Containers (IBC), are considered bulk waste and have a surcharge associated with them (see Tote surcharge CLIN 6386TS). Bulk waste does not refer to containerized wastes including waste contained in drums, cubic yard boxes, military tri-wall boxes, cubic yard bags or “super sacks”, lamp boxes, cylinders, or palletized waste.

b. Bulk debris (as defined in 40 CFR 268.2(g)) and other solids weighing less than 600 Lbs/yd3 shall have the CLIN suffix “B6”, and shall be priced per cubic yard (CD). Bulk debris (as defined in 40 CFR 268.2(g)) and other solids weighing 600 Lbs/yd3 or greater, shall have the CLIN suffix B1, B2, B3, or B4, and shall be priced per pound (LB). Base CLIN TX06 is uniquely designed with the treatment technology of Microencapsulation (of hazardous debris) in mind. Base CLIN TX07 is uniquely designed with the treatment technology of Macro-encapsulation in mind. When ordering Base CLIN TX06 in conjunction with Bulk CLIN Suffixes B1, B2, B3, B4, or B6, the Generator will ensure that the wastestream does not contain pipes, hoses, tubes, equipment, or rigid objects greater than 10 feet in any dimension, where toxic metal surfaces cannot be easily coated with a micro-encapsulation coating material. In such cases where these types of articles are present in bulk loads, Base CLIN TX07 should be considered (maximum size is 18’L x 4.5’W x 4.5’H). Furthermore, intact containers (Per 40 CFR 268.2(g)) do not meet the definition of debris and shall not be turned in under Base CLINs TX06 or TX07. Intact containers are those containers “that are not ruptured and that retain at least 75% of their original volume.” When intact containers are present, the Generator should consider using “Lab Pack/Loose Pack” CLINs.

When ordering a B6 CLIN suffix, the Government shall be required to order disposal of the waste based on a minimum of 75% of the volumetric capacity of the associated rolloff. For example, if a 20 cubic yard rolloff contains 12 cubic yards of debris (B6), the Generator shall pay for disposal of 15 cubic yards, or 75% of the rolloff’s volume.

c. The terms solid and solids used in this document and the Bid Schedule refers to solid material which is largely free of free liquids, e.g., soil, silt, sand, gravel, filtercake, powder, granules, crystals, fines, and artifacts that do not meet the definition of debris as defined in 40 CFR 268.2(g).

d. The terms liquid and liquids used in this document and the Bid Schedule refers to liquid material which is pumpable by conventional pumping devices designed to pump low-viscosity liquids and largely free of suspended or settled (vs. dissolved) solids. A liquid that has become frozen due to ambient freezing temperatures, but would otherwise be of liquid state at 72°F, will still meet the definition of liquid for purposes of this contract.

e. The terms sludge and sludges used in this document and the Bid Schedule refers to material that is either (a) a multiphasic material with some combination of a liquid phase and a solid phase as defined above, (b) a slurry or mud-like material, such as liquid-saturated soil or tank bottoms, whereby solids are largely or completely suspended in liquid and typically flows under gravity, and may or may not be conveyable by high capacity pumping or vacuuming devices designed to move heavy material, or (c) a highly viscous liquid not pumpable by conventional pumping devices designed to pump low-viscosity liquids.

f. The term debris used in this document and the Bid Schedule refers to (a) solid artifacts, fragments, or rubbles which are present, but not primarily present (i.e. incidental), and are intermingled or suspended in an otherwise fully solid, liquid, or sludge wastestream as described above, or (b) a wastestream which meets the definition of debris in 40 CFR 268.2(g). Note:

Definition (a) in this section would meet the “Mixed” or “Various” Physical State designation indicated in the Bid Schedule for this contract, as CLINs with a “Mixed” or “Various” physical state refers to solids, liquids, sludges, debris, or any combination thereof. Definition (b) in this section meets the “Debris” Physical State designation indicated in the Bid Schedule for this contract. CLINs TX06 & TX07 shall be used when the Toxic waste contains >50% debris by volume.

g. The term Heavy Solids used in this document and the Bid Schedule refers to bulk waste solids, sludges, and heavy debris (as defined in 40 CFR 268.2(g)), with a density greater than 600 Lbs/yd3 shall be ordered using the bulk CLIN Suffix (B1, B2, B3, or B4). The CLIN Suffix is assigned based on the net weight of each heavy solids bulk load. If a bulk load with a net weight of less than 10,000 Lbs is ordered, the bulk CLIN Suffix “B1” will be used. Loads weighing 10,000 to 20,000 Lbs will be assigned the bulk CLIN Suffix “B2”. Loads weighing 20,000 to 30,000 Lbs will be assigned the bulk CLIN Suffix “B3”. Loads weighing more than 30,000 Lbs will be assigned the bulk CLIN Suffix “B4”. Weights shall be determined using certified Government scales when available, or certified commercial scales when Government scales are not available. Prior to removal, and when possible, the net weight of the waste shall be determined and agreed upon by both the Government representative and the Contractor.

h. The term Lightweight Solids used in this document and the Bid Schedule refers to bulk waste solids and debris (as defined in 40 CFR 268.2(g)) with a density of less than or equal to 600 Lbs/Yd3. These waste streams are considered lightweight and shall be ordered using the Cubic Yard CLIN Suffix “B6”. Cubic yards (yd3) are calculated by visual estimation. For example, if a 20-yd3 rolloff box appears 90% full, the removal will be estimated and ordered at 18 CD. Note, any CLIN with a “B6” suffix will be ordered using “CD” to denote cubic yards.

Prior to removal, the volume shall be determined and agreed upon by both the Government representative and the Contractor.

i. Bulk waste liquids will be pumpable by conventional pumps typically used on tank trucks and trailers, even if loaded by vacuum truck or trailer, and shall be ordered using the CLIN Suffix B5, indicating gallons (GL).

j. Gallons are calculated by using density or tank strapping and are rounded to the nearest whole gallon using conventional (non-scientific) rounding rules. This rule requires that if the digit to the right of the decimal place is 0, 1, 2, 3, or 4, leave the whole number alone; if the digit to the right of the decimal place is 5, 6, 7, 8, or 9, add 1 to the whole number. Example: when the density calculation is used and where the bulk liquid is water (Density = 8.33 Lbs/Gal): 36,290 Lbs/8.33 Lbs/Gal = 4,356.54 gallons. This will be rounded to 4,357 gallons. However, 36,280 Lbs (4,355.34 gallons) would be rounded to 4,355 gallons. Density will be obtained from the waste profile sheet.

k. Tank strapping may be used to calculate the volume of liquid in a tank or tanker given a strapping rod depth measurement. The graduated rod is inserted vertically through the top surface of the liquid to the bottom of the tank and a measurement is taken to determine the depth of the liquid. The depth, usually measured in inches, is compared to a table, or spreadsheet, which shows the conversion to gallons. Only tables specifically calibrated to the tank or tanker being strapped may be used. These measurements will be made by the Contractor.

l. The Generator reserves the right to choose which method will be used to determine total gallons of waste offered. The net volume (gallons) of the waste shall be determined and agreed upon by both the Government and the Contractor prior to removal, when possible.

m. Liquids in Totes/IBC Containers. When totes/IBCs are removed by the Contractor, the CLIN used for this waste will include the bulk liquid CLIN Suffix of B5. The Generator shall pay the Contractor based upon the full volumetric capacity of the container in gallons, plus a tote surcharge per tote (see Tote disposal surcharge CLIN 6386TS). IBC totes come in various sizes, the most common size being 275- and 330-gallon capacity. Totes/IBCs are transported as containerized waste. When totes/IBCs are pumped/bulked onsite, and the waste is removed via tanker trailer or vacuum truck, the Generator shall pay the Contractor based upon the actual volume removed in gallons (GL).

n. When using the suffix “ME” with CLINs RE10, RE11 and RE12, the “ME” refers to up to 55-gal containers pumped/vacuumed/stung onsite and includes recycling and service. The Generator will guarantee a minimum of 30 containers when ordered. The Contractor may be permitted to, at the discretion of the government be allowed to “top-off” their Vacuum Truck by stinging containers of the same CLIN at no additional cost to the Government. This only applies when servicing a bulk liquid task order of the same base CLIN.

1.2.8.2 CONTAINERIZED WASTE

a. The term containerized waste refers to waste that is typically transported by a box truck or semi-truck and trailer or van, including waste contained in drums, cubic yard boxes, military tri-wall boxes, cubic yard bags or super sacks, lamp boxes, cylinders, or palletized waste.

b. Containers shall be counted, weighed, and documented against the TO by the Contractor prior to removal. Although most containerized CLINs are priced by the container size (CLIN Suffixes C1 through C6), weights must still be documented for other purposes such as manifesting and Generator reporting. The Contractor shall provide portable scales, which may be mounted to the truck or trailer, for weighing of items, and must first demonstrate reasonable weight accuracy to the Government representative. The use of commercial scales is not authorized for containerized items. Only materials being removed by the Contractor will be weighed, including the containers, pallets, and dunnage.

c. Drums larger than 55 gallons (e.g., 95-gal) are to be used only for overpacking smaller drums when the smaller drum(s) are leaking or have the potential to leak. Generators shall be required to pay the Contractor based on the size of the overpack drum and not on the size of the inner, overpacked drum(s).

d. “CYB” (CLIN Suffix “C6”) refers to Cubic Yard Boxes, Cubic Yard Bags or Super Sacks, Gaylord Boxes, and Military Tri-Wall Boxes.

e. “Pallet” (CLIN Suffix “C6”) refers to a flat wooden, plastic or metal transport structure not more than 48” L x 48” W that supports goods in a stable manner while being lifted by a forklift, pallet jack, front loader, or other lifting device. Skids may be used in lieu of pallets when well suited to support the cargo and are accessible to movement via typical material handling equipment. Containers/items placed on a pallet shall be secured with dunnage, i.e., banding straps, stretch or shrink wrap for stability in movement. The sum weight of the dunnage, pallet, and palletized waste cargo will collectively comprise the weight of the waste, and shall not exceed a weight of 2,500 pounds and/or a height of 72” unless otherwise authorized by the Contractor.

f. The cost to the Generator for a CYB and Pallet are the same when the CLIN Suffix C6 is used and packaged IAW current DOT shipping requirements. However, this does not imply that both packaging methods are always appropriate for wastes assigned a CLIN Suffix of C6. Safety and DOT shipping regulations should always take precedence.

g. Containers of the same Base CLIN and no larger than 5 gallons in size, may be palletized or placed in a CYB in order to assign the CLIN Suffix C6. Containers larger than 5 gallons in size will not be placed in a CYB for purposes of consolidating them into a single container.

Containers of all sizes may be placed on pallets and skids for ease of storage and movement, but containers larger than 5 gallons, other than consumer commodities in their original packaging which may be larger than 5 gallons in size, will have the quantity and CLIN assigned as appropriate to each container on the pallet.

h. Most containerized wastes are assigned a CLIN Suffix of C1, C2, C3, C4, C5, or C6.

These CLIN Suffixes correspond to a range of different container sizes and are ordered as each “EA”. CLINs for containerized aerosols, batteries, PCBs and some military items are designated with CLIN Suffix C7 and are ordered in pounds “LB”. CLINs for cylinders and intact lamps have a CLIN Suffix of ME, M1, M2, or M3 and are also ordered as “EA”.

1.2.9 BULK LIQUID PUMPING

a. When a bulk, pumpable liquid (CLIN Suffix “B5”) is ordered, it may be necessary for the Contractor to pump/vacuum waste from tanks, drums, or IBCs. The Contractor is responsible to furnish all equipment and personnel needed to complete this task, including but not limited to, a collection vehicle equipped with pump/vacuum, hoses, fittings, etc.

Pumps/vacuums and hoses shall have a capacity and chemical resistance to safely handle the types of waste to be collected, and remove all pumpable liquids from tanks that can be removed without agitation or introduction of other materials to the tank. Sludge or solids that must be removed by other measures must be ordered using the appropriate CLIN.

b. The actual weight of the material picked up must be identified on the manifest. Bulk liquid removal may be ordered from any location in or around pickup points, in addition to the known sites identified below:

GA Army National Guard Wash Rack & OWS List

FACILITY POC STREET ADDRESS CITY, STATE, ZIP COUNTY

APPROX

SIZE

Albany FMS* Megan Spells 404-803-7476 1500 N. Monroe St. Albany, GA 31702 Dougherty 500

Atlanta CSMS North

Eric Andresen 404-803-7107 935 E. Confederate Ave

Atlanta, GA 30316- 0965 Fulton 500

Atlanta FMS

Eric Andresen 404-803-7107 937 E. Confederate Ave

Atlanta, GA 30316- 0965 Fulton 500

Augusta FMS

Tangy Johnson 404-803-9231 88 Milledge Rd Augusta, GA 30914 Richmond 500

Canton Readiness Center *

Mike Holloway 404-803-9651 1064 Marietta Hwy Canton, GA 30114 Cherokee 500

Clay NGC, OWS 300E

Eric Andresen 404-803-7107

1000 Halsey Ave, Bldg 300 Marietta, GA 30060 Cobb unknown

Cumming Readiness Center

Mike Holloway 404-803-9651 100 Aquatic Circle

Cumming, GA 30040 Forsyth unknown

Dublin FMS * Tangy Johnson 404-803-9231 905 Telfair St Dublin, GA 31040 Laurens 1,300

Ft. Gillem 221st MI BN

Mike Holloway 404-803-9651

4990 N. 20th St., Bldg.

Ft. Gillem, Forest Park, GA 30297 Clayton 100

Ft. Gordon

FMS

Tangy Johnson 404-803-9231

Bldg 21804-21807, 8th Ave

Ft Gordon, GA 30904 Richmond unknown

FS GGTC Grit Basin(Small Vehicle Wash)

Tangy Johnson 404-803-9231 9424 Troupe Ave.

Ft Stewart, GA 31314 Liberty 1,346

FS GGTC

OWS/Grit Basin (CWF)

Tangy Johnson 404-803-9231

Bldg.# 10360 16'th ST & Troupe Ave.

Ft Stewart, GA 31314 Liberty 1,346

FS GGTC State Maintenance

(OWS)

Tangy Johnson 404-803-9231

Bldg 10506 13'th & Troupe Ave.

Ft Stewart, GA 31314 Liberty 500

FS MATES

(ORG Shop) *

Tangy Johnson 404-803-9231 Bldg 10501, Troupe Ave

Ft Stewart, GA 31314 Liberty 500

FS CSMS

South (AT Shop) *

Tangy Johnson 404-803-9231

Bldg 10531, Troupe Ave

31314

Liberty

South (DS Shop) *

Tangy Johnson 404-803-9231 Bldg 10531, Troupe Ave

Ft Stewart, GA 31314 Liberty 500

FS CSMS

South (Grit Chamber/OWS)

Tangy Johnson 404-803-9231 Bldg 10535, Troupe Ave

Ft Stewart, GA 31314 Liberty 1,000

FS MATES

Motor pool (4

OWS) @

Tangy Johnson 404-803-9231

S/E Side Bldg 10501 Motor Pool

Ft Stewart, GA 31314 Liberty 1,000

Hunter AAF

AASF #3

Tangy Johnson 404-803-9231 801 Strachan Blvd

Savannah, GA 31407 Chatham 1,000

Jackson FMS * Megan Spells 404-803-7476 463 Franklin St Jackson, GA 30233 Butts 500

Kennesaw Readiness Center *

Mike Holloway 404-803-9651

1901 McCollum Parkway

Kennesaw, GA 30144

Cobb

Washington

FMS % &

Mike Holloway 404-803-9651 500 Water St.

Washington, GA 30673 Wilkes 500

UTES Ft Gordon OWS/Grit Chamber %

Tangy Johnson 404-803-9231 13th St. Ft Gordon Ft Gordon, GA Richmond 1,390

Winder AASF #1 %

Eric Andresen 404-803-7107 889 Ronald Wood Rd. Winder, GA 30680 Barrow 1,000

Winder FMS %

Eric Andresen 404-803-7107 889 Ronald Wood Rd. Winder, GA 30680 Barrow 1,000

ACTIVE DUTY INSTALLATIONS

* = 500-gallon Surge Tank @ = 1,000-gallon Surge Tank % = 1,000-gallon Grit Chamber & = In-ground coalescing plate OWS

1.2.10 BULKING & CONSOLIDATION

a. Bulking shall be defined as the act of stinging, vacuuming, and/or pumping, as permitted by regulation, from an otherwise removable container(s) into a vacuum truck or tanker. This act may be performed at the discretion of the Contractor, at no additional cost to the Generator.

Containerized waste may be bulked into a tank truck only at the locations listed below:

• GA ARNG pick-up points

• Robins AFB

b. Consolidation is defined as any method that involves pouring, siphoning, pumping, draining, or packaging like wastes (liquids, multiphase, or solids) from one container to another.

Wastes may be consolidated only at the locations listed below:

• GA ARNG pick-up points

• Robins AFB

c. Bulking and consolidation will be allowed only if the Contractor has a spill contingency plan and performs operations in a safe manner. The Government retains the right to stop operations if environmental or safety concerns arise.

1.2.11 EXPEDITED SERVICES - CLINs 6331-6335, 6341-6345

a. When the expedited removal CLINs are ordered, waste must be removed within the specified calendar day timeframe. Expedited removal CLINs may be ordered in association with any disposal CLIN(s) at any pick-up point(s) in the contract. This is an exception to the standard removal timeframe as specified in Section 7. Minimum TO charges will not apply to a TO containing an expedited removal CLIN. When expedited removal is required, CLINs 6330-34 will be ordered based on the amount of waste to be removed.