RFQ_Attach_5-Maint_Task_Lists.pdf

Attachment 5

MAINTENANCE TASK LIST #1

TYPE EQUIPMENT: Truck, 6 x 4 Tractor, Diesel

(DLA OWNED-NOT GSA)

TASK FREQUENCY

NOTES

SEMI-ANNUAL ANNUAL

1. Lube all points X X 1

2. Cooling System/ Antifreeze/Radiator

X X 5

3. Wheel Bearings X X 2

4. Engine Oil & Filter X X 3

5. Air Intake System X X 4

6. Hydraulic System X X 4

7. Engine X X 6

8. Transmission X X 6

9. Steering System X X 7

10. Exhaust System X X 8

11. Safety Inspection X X 9

12. Fifth Wheel Assembly X X 10 Notes:

1. Lubricates all grease fittings.

2. Clean, impact & Re-pack annually; replace seals/gaskets if required.

3. Change oil and filter annually; check semi-annually and add if required.

4. Change/clean filter element annually; check for defective parts; check semi-annually.

5. Check level and top-off; check hoses; and fittings for leaks;

6. Check engine, tune up annually if required, transmission for proper operations as required.

7. Check for excessive backlash; check for leaks or damage. Lubricate grease fittings as required; check tires for excess wear and correct air pressure.

8. Check annually exhausts manifold, pipes, muffler, and hangars/clamps for leaks or damage.

9. Inspection of all safety related components, to include as a minimum, front and rear lights, air brakes, brake pedals, tires, horn, back-up alarm, guard and fire extinguisher.

10. Check for binding, looseness, or damage to locking jaws. Lubricate pivot points.

Check for full operation raise and lower. Refer to manufacturer’s documentation.

MAINTENANCE TASK LIST #2

TYPE EQUIPMENT: Truck, Trailer Spotting, Diesel

SEMI-ANNUAL ANNUAL

1. Lube all points X X 1

2. Cooling System/

Antifreeze/Radiator X X 5

3. Wheel Bearings X X 2

4. Engine Oil & Filter X X 3

5. Air Intake System X X 4

6. Hydraulic System X X 4

7. Engine X X 6

8. Transmission X X 6

9. Steering System X X 7

10. Exhaust System X X 8

11. Safety Inspection X X 9

12. Fifth Wheel Assembly X X 10

2. Clean, impact & re-pack annually; replace seals/gaskets if required.

3. Change oil and filter annually; check semi-annually and add if required.

4. Change/clean filter element annually; check for defective parts; check semi-annually.

5. Check level and top-off; check hoses; and fittings for leaks;

6. Check engine, tune up annually if required, transmission for proper operations as required.

7. Check for excessive backlash; check for leaks or damage. Lubricate grease fittings as required; check tires for excess wear and correct air pressure.

8. Check annually exhausts manifold, pipes, muffler, and hangars/clamps for leaks or damage.

9. Inspection of all safety related components, to include as a minimum, front and rear lights, air brakes, brake pedals, tires, horn, back-up alarm, guard and fire extinguisher.

MAINTENANCE TASK LIST #3

TYPE EQUIPMENT: Truck, Utility, Stake, Van or Pick-up-Diesel & Gas

(DLA OWNED-NOT GSA)

SEMI-ANNUAL ANNUAL

1. Lube all points X X 1

2. Cooling System/ Antifreeze/Radiator

X X 5

3. Wheel Bearings X X 2

4. Engine Oil & Filter X X 3

5. Air Intake System X X 4

6. Hydraulic System X X 4

7. Engine X X 6

8. Transmission X X 6

9. Steering System X X 7

10. Exhaust System X X 8

11. Safety Inspection X X 9

12. Tail Gate Assembly X X 10

3. Change oil and filter annually; check semi-annually and add if required.

4. Change/clean filter element annually; check for defective parts; check semi-annually.

5. Check level and top-off; check hoses; and fittings for leaks;

6. Check engine, tune up annually if required, transmission for proper operations as required.

7. Check for excessive backlash; check for leaks or damage. Lubricate grease fittings as required; check tires for excess wear and correct air pressure.

8. Check annually exhausts manifold, pipes, muffler, and hangars/clamps for leaks or damage.

9. Inspection of all safety related components, to include as a minimum, front and rear lights, air brakes, brake pedals, tires, horn, back-up alarm, guard and fire extinguisher.

MAINTENANCE TASK LIST #4

TYPE EQUIPMENT: Transporter Truck (Conveyorized), Diesel, with belt or roller bed

SEMI-ANNUAL ANNUAL

1. Lube all points X X 1

2. Cooling System/ Antifreeze/Radiator

X X 5

3. Wheel Bearings X X 2

4. Engine Oil & Filter X X 3

5. Air Intake System X X 4

6. Hydraulic System X X 4

7. Engine X X 6

8. Transmission & PTO X X 6

9. Steering System X X 7

10. Exhaust System X X 8

11. Safety Inspection X X 9

12. Pallet Belt/Roller Assembly X X 10

3. Change oil and filter annually; check semi-annually and add if required.

4. Change/clean filter element annually; check for defective parts; check semi-annually.

5. Check level and top-off; check hoses; and fittings for leaks;

6. Check engine, transmission, PTO for proper operations as required.

7. Check for excessive backlash; check for leaks or damage. Lubricate grease fittings as required; check tires for excess wear and correct air pressure.

8. Check annually exhausts manifold, pipes, muffler, and hangars/clamps for leaks or damage.

9. Inspection of all safety related components, to include as a minimum, front and rear lights, brakes, brake pedals, tires, horn, back-up alarm, guard and fire extinguisher. Check operation of pallet stop.

10. Check all roller bearings/belt for binding, looseness, or damage; check chain (s) for length, proper adjustment, excessive wear, or damage. Lubricate pivot points. Check for full operation raise and lower. Check belt/roller positioning devices. Refer to manufacturer’s documentation.

MAINTENANCE TASK LIST #5

TYPE EQUIPMENT: Warehouse Sweeper, DSL & Propane, Gas Riding and Walking DLA AVIATION – ANNUAL PM ONLY

SEMI-ANNUAL ANNUAL

1. Lube Chassis X X 1

2. Engine Oil and Filter X X 2

3. Hydraulic System X X 2

4. Air Cleaner X X 2

5. Lights and Lenses X X 3

6. Safety Inspection X X 3

7. Clean Engine X 4

8. Adjust Belts, Brooms X X 5

9. Clean Hopper X X 4

10. Check Operation X X 5

11. Battery X X 2

1. Lubricate, add grease, per manufacturer ’s specifications.

2. Clean machine of dirt and grime; change oil and filter, replace per manufacturer specifications; change/clean air cleaner; check and fill battery electrolyte, check cables and connections for damage; check hydraulic system for proper operation, leaks and defective components and fill reservoir. Change hydraulic oil if contaminated.

3. Check all components which are safety related; inspect all lights and lenses for proper operation and damage.

4. Clean compartment with compressed air.

5. Adjust all belts and brooms for proper operation; operational run to assure equipment is functioning properly.

MAINTENANCE TASK LIST #6

TYPE EQUIPMENT: Warehouse Tractor, Elec, Gas & Propane

SEMI-ANNUAL ANNUAL

1. Lube Chassis X X 1

2. Antifreeze X X 2

3. Wheel Bearings X 3

4. Engine Oil and Filter X X 4

5. Fuel Filter X 4

6. Air Cleaner X X 4

7. Brakes X X 5

8. Transmission & Trans Oil Filter X X 9

9. Safety Inspection X X 6

10. Clean X X 8

11. Operational Check X X 6

12. Battery X X 5

13. Tires X X 7

1. Lube all points

2. Top off; change if contaminated.

3. Steering Axle (s) only; Inspect, clean, adjust Repack.

4. Change engine oil, fuel filter (s) and clean air filters semi-annual and change annual

5. Check levels; Add as required; Remove excess acid residue buildup and clean battery surface; check brake lines, connections for leaks and change fluid if contaminated; check brake wear, adjust as required.

6. Inspect all safety related components; Check lights/lenses; Check pintle hook for damage; Perform operational run for proper operation of all systems.

7. Check pressure and wear on pneumatic rubber tires (PRT); Check for excessive wear.

8. Clean engine and engine compartment with compressed air

9. Change Trans oil annually and filter semi-annually (if applicable)

MAINTENANCE TASK LIST #7

TYPE EQUIPMENT: Forklift, Gas & Propane (ALL)

SEMI-ANNUAL ANNUAL

1. Lube Chassis X X 1

2. Antifreeze X X 2

3. Wheel Bearings X X 3

4. Engine Oil and Filter X 4

5. Fuel Filter X 4

6. Hydraulic System & Filter X 4

7. Air Cleaner X 4

8. Gear Boxes X X 5

9. Lights & Lenses X X 6

10. Brakes X X 6

11. Transmission X X 2

12. Safety Inspection X X 6

13. Operational Check X X 6

14. Battery X X 5

15. Tires X X 7

16. Mast and Carriage X X 8

1. Lube all points.

2. Top off; change if contaminated.

3. Repack, inspect.

4. Change oil, fuel, hydraulic system filters and clean/change air filters; check hydraulic oil system lines/hoses and reservoirs, and top-off.

5. Check levels; add as required; remove excess acid residue buildup, and clean battery surface; check brake lines, connections for leaks and change fluid if contaminated; check brake wear; replace seals/gaskets as required.

6. Inspect all safety related components; check lights/lenses; perform operational run for proper operation of all systems.

7. Check pressure and wear on pneumatic rubber tires (PRT); check for excessive wear and damage to solid rubber tires (SRT).

8. Check linkage for damage; adjust to manufacturer's specifications.

MAINTENANCE TASK LIST #8

TYPE EQUIPMENT: Stock Selectors, Waves, Turret Truck, Electric and Wire-Guided 2,000-6,000 lbs CAP

DLA AVIATION – ANNUAL PM ONLY

SEMI-ANNUAL ANNUAL

1. Lubricate all points X

2. Wheel Bearings X X 2

3. Hydraulic Oil Filters X 6

4. All Fluids X X 3

5. Motor Drive X X 1

6. Battery, Clean & Service X X 8

7. Hoist and Carriage Chains X X 4

8. Safety Inspection X X 5

9. Load Certification X 7

1. Check

2. Inspect, re-pack, clean and adjust as necessary. Replacement of wheel bearings shall be accomplished under remedial maintenance, as agreed to by the COR.

3. Check fluid levels in gear boxes, hydraulics, transmissions, differential and brakes.

Top off semi-annually; change annually

4. Lubricate, inspect, check tension.

5. Inspect all safety components to include front and rear lights, brakes, brake pedals, tires horn, back-up alarm, overhead guard and fire extinguisher. All repairs required as a result of Safety Inspection shall be accomplished under Remedial Maintenance, with the approval of the COR.

6. Replaceable filters checked semi-annually, change annually; Reusable screen filters clean semi-annually and annually.

7. In accordance with Code of Federal Regulation (CFR) 29, Part 1910; stencil Capacity when required.

8. Inspect, maintain; check/fill battery water level; inspect cables and connections for damage.

MAINTENANCE TASK LIST #9

TYPE EQUIPMENT: Forklift, Diesel 4,000-45,000 LBS CAP, PRT

SEMI-ANNUAL ANNUAL

1. Lube Chassis, Mast & Carriage X X 1

2. Antifreeze X X 2

3. Wheel Bearings X 3

4. Engine Oil and Filter X 4

5. Fuel Filter X 4

6. Hydraulic System & Filter X 4

7. Air Cleaner X X 4

8. Gear Boxes X X 5

9. Lights & Lenses X X 6

10. Brakes X X 5

11. Transmission X 5

12. Safety Inspection X X 6

13. Operational Check X X 6

14. Battery X X 5

15. Tires X X 7

16. Chains, check & adjust X X 8

2. Top off; change if contaminated

3. Repack, inspect

4. Change oil, fuel, hydraulic system filters and clean/change air filters; Change engine oil; Check hydraulic oil system lines/hoses and reservoirs and top-off

5. Check levels; Add as required; Remove excess acid residue buildup and clean battery surface; check brake lines, connections for leaks and change fluid if contaminated; check brake wear. Replace seals/gaskets as required

6. Inspect all safety related components; Check lights/lenses; Check pintle hook for damage; Perform operational run for proper operation of all systems

7. Check pressure and wear on pneumatic rubber tires (PRT); Check for excessive wear and damage to solid rubber tires (SRT).

8. Check linkage for damage; Adjust to Mfr.’s specification

MAINTENANCE TASK LIST #10

TYPE EQUIPMENT: Forklift, Electric (ALL)

SEMI-ANNUAL ANNUAL

1. Lubricate Chassis X

2. Wheel Bearings X 1

3. Check Motor Brushes (Drive) X X

4. Check Contact Points X X 2

5. Hydraulic System & Filter X X 3

6. Electric Motor X X 2

7. Lights and Lenses X X 4

8. Brakes X X 5

9. Safety Inspection X X 4

10. Load Test X 4

11. Operational Check X X 6

12. Battery X X 7

13. Lift Chains X X 4 & 6

1. Inspect and repack; replace necessary seals/gaskets

2. Inspect for burned, pitted or damage; Replace if defective. Clean and check Electric motor.

3. Inspect lines/hoses for damage or leaks; Clean/Replace filter annually; Change hydraulic oil if contaminated; Top off reservoir.

4. Load test in accordance with CFR 29, part 1910.

5. Check for wear; Check for proper operation; Inspect for damaged, worn or broken parts; replace necessary seals and gaskets

6. Inspect all safety related components; Check lights/lenses; Check brakes and brake pedal; check emergency brake; check fire extinguisher; perform operational run for proper operation of all systems. All repairs required by virtue of a safety inspection, shall be accomplished under Remedial maintenance

7. Top off electrolyte levels; Check cables/connectors for damage; Clean off exterior of Batteries and remove all acid build-up

MAINTENANCE TASK LIST #11

TYPE EQUIPMENT: Trailer, Special Purpose

SEMI-ANNUAL ANNUAL

1. Lube Chassis X X 2

2. Check Tire Pressure X 3

3. Pack Wheel Bearings X 5

4. Brakes-Clean, Check & Adjust X 4

5. Safety Inspection X X 1

6. Check Auxiliary Engine X X 6

7. Change Oil & Fuel Filters X 7

8. Check Operation of Refrigeration Unit

X

1. Inspect all safety related components to include as a minimum, rear lights, brakes tires, reflectors and air brake system for damage and proper operation

2. Lubricate all points per manufacturer ’s recommendations.

3. Do not mix Radial with Bias ply tires on same vehicle. Check the pressure when tires are cold. Check for unusual wear; If required, rotate and match according to tread design and degree of wear.

4. Inspect airlines, reservoir and fittings for damage or leaks; Drain accumulated condensate from air reservoir; Inspect all valves, air chambers, fittings and connecting lines for damage and defects. Check and Adjust last adjusters

5. Inspect, Repack, clean and adjust as necessary.

6. Inspect operation of auxiliary engine

7. Change oil and fuel filters

8. Check operation of refrigeration unit.

MAINTENANCE TASK LIST #12

TYPE EQUIPMENT: Battery Chargers 24-48 Volts

SEMI-ANNUAL ANNUAL

1. Battery Chargers

1. Dust interior & exterior. Inspect cables, connectors, straps and jumpers. Check conductivity and resistance voltage.

MAINTENANCE TASK LIST #13

TYPE EQUIPMENT: Trailer, Semi-Flatbed, Stake, Lowbed at all Capacities

SEMI-ANNUAL ANNUAL

1. Lube Chassis X 2

2. Check Tire Pressure X 3

3. Pack Wheel Bearings X 5

4. Brakes-Clean, Check & Adjust X 4

5. Safety Inspection X 1

2. Lubricate all points per manufacturers recommendations.

3. Do not mix Radial with Bias ply tires on same vehicle. Check the pressure when tires are cold. Check for unusual wear; If required, rotate and match according to tread design and degree of wear.

4. Inspect airlines, reservoir and fittings for damage or leaks; Drain accumulated Condensate from air reservoir; Inspect all valves, air chambers, fittings and

Connecting lines for damage and defects. Check and Adjust last adjusters

5. Inspect, Repack, clean and adjust as necessary.

MAINTENANCE TASK LIST #14

TYPE EQUIPMENT: Trailer, Warehouse, Flatbed, Unpowered & 7k Retriever Trailer and Ground Trailers

SEMI-ANNUAL ANNUAL

1. Lube Chassis X 2

2. Check Tire Pressure X 3

3. Pack Wheel Bearings X 5

4. Safety Inspection X 1

2. Lubricate all points per manufacturer ’s recommendations.

3. Do not mix Radial with Bias ply tires on same vehicle. Check the pressure when tires are cold. Check for unusual wear; If required, rotate and match according to tread design and degree of wear.

4. Inspect airlines, reservoir and fittings for damage or leaks; Drain accumulated condensate from air reservoir; Inspect all valves, air chambers, fittings and connecting lines for damage and defects. Check and Adjust last adjusters

5. Inspect, Repack, clean and adjust as necessary.

MAINTENANCE TASK LIST #15

TYPE EQUIPMENT: Scooter, 3-4 Wheeled Gas & Electric

SEMI-ANNUAL ANNUAL

1. Lubrication X 1

2. Electric Motor X 2

3. Tires & Wheel Bearings X 3

4. Battery X 4

5. Brakes X 5

6. Safety Check X 6

7. Clean Inside & Outside X 8

1. Lube all points, per manufacturer specifications.

2. Check wire connections for damage: Clean residual from motor.

3. Inspect for damage and proper inflation; Inspect, clean and repack wheel bearings.

4. Check connections for damage, Top-off electrolyte level and remove acid residue.

Buildup annually and semi-annually. Check specific gravity annually.

5. Check for proper operation and damage or defects.

6. Inspect all safety related components for proper operation and damage.

7. Operate and assure that all equipment systems are functioning properly.

8. Clean engine & engine compartment with compressed air.

MAINTENANCE TASK LIST #16

TYPE EQUIPMENT: Loader, Wheeled, Front –End Diesel

SEMI-ANNUAL ANNUAL

1. Lube all points X X 1

2. Cooling System/

Antifreeze/Radiator X X 5

3. Axle Oil Reservoir X X 2

4. Engine Oil & Filter X X 3

5. Air Intake System X X 4

6. Hydraulic System X X 4

7. Engine X X 6

8. Transmission X X 6

9. Steering System X 7

10. Exhaust System X 8

11. Safety Inspection X X 9

12. Loader Bucket & Attachments X X 10

2. Check and inspect; replace seals/gaskets if required.

3. Change oil and filter annually; check semi-annually and add if required.

4. Change/clean filter element annually; check for defective parts; check semi-annually.

5. Check level and top-off; check hoses; and fittings for leaks;

6. Check engine, tune up annually if required, transmission for proper operations as required.

7. Check for excessive backlash; check for leaks or damage. Lubricate grease fittings as required; check tires for excess wear and correct air pressure.

8. Check annually exhausts manifold, pipes, muffler, and hangars/clamps for leaks or damage.

9. Inspection of all safety related components, to include as a minimum, front and rear lights, air brakes, brake pedals, tires, horn, back-up alarm, guard and fire extinguisher.

Check for full operation raise and lower. Refer to manufacturer ’s documentation.

MAINTENANCE TASK LIST #17

TYPE EQUIPMENT: Crane, Crawler, Diesel & Electric

SEMI-ANNUAL ANNUAL

1. Lube all points X X 1

2. Cooling System/

Antifreeze/Radiator X X 5

3. Check & Inspect Cables for fraying

4. Engine Oil & Filter X X 3

5. Check tracks and rollers X X 7

6. Check for wear on boom X X 4

7. Engine X X 6

8. Transmission X X 6

9. Inspection Date X X 10

10. Exhaust System X X 8

11. Safety Inspection X X 9

2. Check and inspect; replace seals/gaskets if required.

3. Change oil and filter annually; check semi-annually and add if required.

4. Change/clean filter element annually; check for defective parts; check semi-annually.

5. Check level and top-off; check hoses; and fittings for leaks;

6. Check engine, tune up annually if required, transmission for proper operations as required.

7. Check for excessive play in track pins and connections.

8. Check annually exhausts manifold, pipes, muffler, and hangars/clamps for leaks or damage.

9. Inspection of all safety related components, to include as a minimum, front and rear lights, air brakes, brake pedals, tires, horn, back-up alarm, guard and fire extinguisher.

10. Following all safety inspections required by manufacturers requirements, stencil

Inspection Date on unit.

MAINTENANCE TASK LIST #18

TYPE EQUIPMENT: Mobile Trailer Ramp (Loading Ramp)

SEMI-ANNUAL ANNUAL

1. Inspect structure X X 1

2. Inspect Chain & Restraint X X 2

3. Operate & Lube Lift Mechanism X X 3

4. Inspect Tires & Wheels X X 4

5. Check Hydraulic Oil Reservoir X X 5

1. Inspect structure before each use for any defects. (i.e. broken welds, stress cracks, etc.).

2. Verify restraint chain is connected to dock and the dock connector is firmly embedded into dock.

3. Check hydraulic system for proper operation, defective components.

4. Inflate to 100 psi. Check for cracking or deformations.

5. Oil should be filled with ¼” of top of reservoir when yard ramp is in the fully lowered position.

MAINTENANCE TASK LIST #19

TYPE EQUIPMENT: Floor Scrubbing Machine, Electric

SEMI-ANNUAL ANNUAL

1. Lube Chassis X 1

2. Check Battery X 2

3. Air System X 3

4. Hydraulic System X 2

5. Air Cleaner X 2

6. Lights and Lenses X 4

7. Safety Inspection X 4

8. Adjust Belts, Brooms X 6

9. Clean Hopper X 5

10. Check Operation X 6

1. Lubricate, add grease, per manufacturer ’s specifications.

2. Clean air filter; change oil and filter, replace per manufacturer specifications; change/clean air cleaner; check and fill battery electrolyte, check cables and connections for damage; check hydraulic system for leaks and defective components and fill reservoir. Change hydraulic oil if contaminated.

3. Check air system for proper operation, defective components.

4. Check all components which are safety related; inspect all lights and lenses for proper operation and damage.

5. Clean compartment with compressed air.

6. Adjust all belts and brooms for proper operation; operational run to assure equipment is functioning properly.

MAINTENANCE TASK LIST #20

TYPE EQUIPMENT: Warehouse Tractor Tow Truck (Tugger) 10k Electric

SEMI-ANNUAL ANNUAL

1. Lube Chassis X X 1

2. Wheel Bearings X 2

3. Brakes X X 3

4. Hydraulic Oil X 7

5. Safety Inspection X X 4

6. Clean X X 6

7. Operational Check X X 4

8. Battery X X 3

9. Tires X X 5

2. Steering Axle (s) only; Inspect, clean, adjust Repack.

3. Check levels; Add as required; Remove excess acid residue buildup and clean battery surface; check brake lines, connections for leaks and change fluid if contaminated; check brake wear, adjust as required.

4. Inspect all safety related components; Check lights/lenses; Check pintle hook for damage; Perform operational run for proper operation of all systems.

5. Check pressure and wear on pneumatic rubber tires (PRT); Check for excessive wear.

6. Clean compartment with compressed air

7. Check and drain hydraulic oil annually

MAINTENANCE TASK LIST #21

TYPE EQUIPMENT: Platform Maint Telescope (LPG)

SEMI-ANNUAL ANNUAL

1. Lubricate Chassis X X

2. Wheel Bearings X 1

3. Engine Oil & Filter X 7

4. Hydraulic System & Filter X X 2

5. Lights and Lenses X X 3

6. Brakes X X 4

7. Safety Inspection X X 3

8. Load Test X X 3

9. Operational Check X X 5

10. Battery X X 6

2. Inspect lines/hoses for damage or leaks; Clean/Replace filter annually; Change hydraulic oil if contaminated; Top off reservoir.

3. Load test in accordance with CFR 29, part 1910.

4. Check for wear; Check for proper operation; Inspect for damaged, worn or broken parts; replace necessary seals and gaskets

5. Inspect all safety related components; Check lights/lenses; Check brakes and brake pedal; check emergency brake; check fire extinguisher; perform operational run for proper operation of all systems. All repairs required by virtue of a safety inspection, shall be accomplished under Remedial maintenance

6. Top off electrolyte levels; Check cables/connectors for damage; Clean off exterior of batteries and remove all acid build-up.

7. Change engine oil, fuel filter (s) and clean air filters semi-annual and change annual

MAINTENANCE TASK LIST #22

TYPE EQUIPMENT: Scaffold, Mobile-Battery Powered (ELEC)

SEMI-ANNUAL ANNUAL

1. Lubricate Chassis X

2. Wheel Bearings X 1

3. Check Motor Brushes (Drive) X X 2

4. Check Contact Points X X 2

5. Hydraulic System & Filter X X 3

6. Electric Motor X X 2

7. Lights and Lenses X X 4

8. Brakes X X 5

9. Safety Inspection X 4

10. Load Test X X 4

11. Operational Check X X 6

12. Battery X X 7

2. Inspect for burned, pitted or damage; Replace if defective. Clean and check

Electric motor.

3. Inspect lines/hoses for damage or leaks; Clean/Replace filter annually; Change hydraulic oil if contaminated; Top off reservoir.

4. Load test in accordance with CFR 29, part 1910.

5. Check for wear; Check for proper operation; Inspect for damaged, worn or broken parts; replace necessary seals and gaskets

6. Inspect all safety related components; Check lights/lenses; Check brakes and brake pedal; check emergency brake; check fire extinguisher; perform operational run for proper operation of all systems. All repairs required by virtue of a safety inspection, shall be accomplished under Remedial maintenance

7. Top off electrolyte levels; Check cables/connectors for damage; Clean off exterior of Batteries and remove all acid build-up