SO-1826 Hill CTE Renovations Phase 2 Addendum 2.pdf

Lansing School District Hill Center Summer 2025 Renovations Bid Package 1

Pre-Bid Addendum 02

Addendum 02

February 27, 2025

This document is to serve as Addendum No. 02 with the purpose of providing clarifications or modifications to the original bid documents dated February 07, 2025 and shall take precedence over them. All incidental items required for the following changes are to be included even if not specifically described.

Receipt of this addendum is to be noted on the bid form.

ATTACHMENTS: -2025_02_26 Hill Center_ADD 01 Write-up

-2025_02_26_Hill Center_ADD 01 Drawings -WC23A project manual section -WC26A project manual section -WC 31A project manual section

BID DATE: Bid date remains UNCHANGED.

BID FORM: Bid form remains UNCHANGED

DRAWINGS: Drawings reissued by Kingscott, see attached

TECH SPECS: Not Applicable

RFI RESPONSES: Q: Is this project prevailing wages? Will the landscaping scope include the 12" planting soil near the entry? The RFP says proposals have to be hand delivered?

A: Project is NOT prevailing wage, please see Addendum 1. Yes include 12” planting soil near entry. Yes all proposals need to be hand delivered per the project manual.

Q: Will the current receptacles in all classroom areas need to be upgraded to Tamper Proof as per NEC? IF so, will the plans be updated showing qtys? Is the EC responsible for the Access Control cabling or Conduit/Raceways only? Is the EC responsible for the Telecommunications cabling?

A: Plans have been updated to indicate tamper proof. EC is responsible for access control cabling and conduits/raceways. EC is responsible for telecommunications cabling.

Q: Line Item 10 under work category 31A states that the excavation and prep for new concrete walk/curb/gutter, new frost blocks, and asphalt is going to be done by WC 03A. There is not a WC 03A category listed for this project. Is this work all supposed to be included in WC 31A? Please advise A: WC31A Clarified in project manual. Please include all excavation and prep for new concrete and asphalt. Please provide and install all concrete walk/curb/gutter, frost blocks, and asphalt paving as shown on the plans.

Q: Clarify food service specs for mechanical vendor to supply A: WC 23A clarified in project manual, see updated WC23A section in project manual.

Q: What is HVAC scope in regard to Alternate #1A, #1B, #1c?

A: HVAC Alternate 1A, 1B, 1C refers to the demo and new work as shown in the 2nd floor classrooms and teachers' lounge. Per the plans it is replacement of diffusers in new ceilings in C210, C211B, and C211, and cleaning of existing diffusers in D216, D215, D210, and D209

Q: WC 31A: I don't see anything in there regarding installing concrete paving. It mentions asphalt paving.

A: WC 31A clarified in project manual, see updated WC31A section in project manual.

Q: Could you clarify whether a bid bond is still required for this scope of work?

A: The Bid form states "Bid security (bid bond or cashier’s check) in the amount of 5% of the bid amount will be required with all bid submission."

Q: Please clarify who is providing Mechanical vs FoodService ducts/hoods/etc.

A: WC 23A clarified in project manual, see updated WC23A section in project manual

Q: Door 100A is currently a pair of doors with a fixed mullion – you are showing a single door and frame going back in but do not show any wall being rebuilt – Please Clarify?

Doors 100B & 100C show up on finish hardware set #6 but not on the floor plan – Please clarify? Please verify that BL-1 are hollow metal frames?

A: 100A is replacing the existing cafeteria entrance only, the double doors will remain.

Please see updated drawings for answer to remaining questions.

Q: The MAU calls out for the controls to be by the TCC, The Food Service Drawings (Captive Aire) have the controls Included. Please confirm the responsibility of the TCC regarding the MAU and EF’s. If the controls are to be by Manufacture, please confirm that the controls are BACnet and to be configured by the manufacture, and TCC has the responsibility of Integrating only.

A. Please see updated drawings.

Q: Is there any additional information for insulated glass, other than drawing notes that state 1” INSUL or 1” Insulated Glazing? Should we assume 1” Clear, Low-e Glass for lack of a specification?

A: Glass specifications added to updated drawings

PROJECT MANUAL: WC 23A, Note 31: Please review Section 114000 – FOODSERVICE EQUIPMENT: Item 10

Ventilation Hood: Provide and install Items noted N.I.F.E.C. including items 28-31 noted.

WC 26a, Note 25: Provide and install all access control conduit, wiring, and devices.

Existing equipment manufacturer is EPS

WC 31A, Note 10: WC 31A will excavate and prep for new concrete walk/curb/gutter, new frost block (3) at out swinging entry doors, and asphalt.

WC31A, Note 11: Subbase will be furnished, installed, and graded to within +/-.10’ by this WC. This WC to perform any fine grading required prior to installation of their work.

WC 31A, Note 17: Provide and install all concrete paving, sidewalks, frost walls noted in the plans. Provide and install all landscaping noted in the plans.

END OF ADDENDUM 02

Date: 02/26/2025

Project: Hill Center Summer 2025 Renovations

Owner: Lansing School District

Location: Lansing, MI

A/E #: 2612.03

ADDENDUM NO. 01

SPECIAL NOTE:

The Notice to Bidders, Instructions to Bidders, General Conditions of the Contract for Construction, Supplementary Conditions of the Contract for Construction, and all modifications and previously issued

Contract Documentation are a part of this Addendum.

SCOPE OF WORK:

The following items are changes, additions, deletions, clarifications and/or errors and omissions in plans & specifications and shall be considered by each Bidder in making up and submitting their proposal. All items shall be considered a part of the Contract Documents.

NOTICE TO ALL BIDDERS:

All Bidders shall take note of all items covered by this Addendum. Each Bidder shall review the total scope of his responsibilities with respect to his contract work and his interface with the work of others, as well as his required interface with their work.

DRAWINGS:

G0.1 (reissued)

• Sheet list modified to include new sheets D1.2B, D2.12B, A1.2B, A2.2B, A8.2B, MD1.2B, M1.2B, ED1.2B, EP1.2B, EL1.2B.

L1.0 (reissued)

• Updated shrubs at entry.

A0.1 (reissued)

• Added additional scope.

D1.2 (reissued)

• Modified door to match existing size.

D1.2B (issued)

• New scope in Room 150.

D1.3 (reissued)

• Modified door to match existing size.

D2.12B (issued)

• New scope in Room 150/151.

A1.2 (reissued)

• Modified door 100D to match existing size.

A1.2B (issued)

A1.3 (reissued)

• Modified door 100D to match existing size.

A2.2B (issued)

A6.1 (reissued)

• Changed door 100D to match existing size (double door) with frame type 4.

• Added hollow metal frames, wood door, and glazing spec.

A8.2B (issued)

M0.0 (re-issued):

• Sheet list modified to include MD1.2B and M1.2B.

MD1.2B (issued):

• Added sheet to drawing set for additional scope.

FP1.0 (re-issued):

• Added scope as indicated

P4.0 (re-issued):

• Revised Plumbing Fixture Schedule to include SK-2.

M1.2B (issued):

M6.0 (re-issued):

• Added diffuser types as indicated.

M8.0 (re-issued):

• Revised sequence as indicated.

M9.1 (re-issued):

• Revised specifications as indicated.

E0.0(not issued):

• Updated sheet index.

ED1.2 (not issued):

• Added Electrical Demo Key Note D7 – not applicable to sheet.

ED1.2B (issued):

• Added sheet to drawing set for additional scope in classroom 150/151.

ED1.3 (not issued):

ED1.11 (not issued):

ED1.14 (not issued):

EP1.2 (not issued)

• Added Electrical General Note #6.

EP1.2B (issued):

EP1.3 (not issued):

EP1.3R (not issued):

EP1.11 (not issued):

EP1.4 (not issued):

EL1.2 (not issued):

• Added Lighting Keynote #L2 and #L3

EL1.2B (issued):

EL1.3 (not issued):

EL1.11 (not issued):

EL1.14 (not issued):

END OF ADDENDUM

KINGSCOTT ASSOCIATES INC. KALAMAZOO, MICHIGANCC

JOB NO.

SHEET TITLE

SHEET NO.

ISSUANCES DATE

N

KEY PLAN

P L

E A

S E

R E

C Y

C L

E

T H

E S

E D

R A

W

IN

G S

A N

D T

H E

W O

R K

R E

P R

E S

E N

T E

D T

H E

R E

IN

A

R E

T H

E P

R O

P E

R T

Y O

F A

N D

C

O P

Y R

IG

H

T

K

IN

G

S C

O T

T A

S S

O C

IA

T

E S

A

D

M A

Y N

O T

B E

U S

E D

O R

R E

P R

O D

U C

W

IT

H

O U

T P

E R

M

IS

S

IO

N

L A

S T

P R

IN

T

E D ljh

CLIENT:

LANSING SCHOOL DISTRICT

519 WEST KALAMAZOO ST.

LANSING, MI

TEL. (517) 755-1000

ARCHITECT:

KINGSCOTT ASSOCIATES INC.

259 E MICHIGAN AVE, SUITE 308

KALAMAZOO, MI 49007

TEL. (800) 632-7815

MEP ENGINEER:

SES ENGINEERING

4000 WEST 11 MILE ROAD

BERKLEY, MI 48072

TEL. (248) 399-1900

DIRECTORY

KALAMAZOO | CHELSEA | GRAND RAPIDS | ROYAL OAK

STRUCTURAL ENGINEER:

ROBERT DARVAS ASSOCIATES

440 S MAIN ST.

ANN ARBOR, MI

TEL. (734) 761-8713

CIVIL ENGINEER:

SPALDING DEDECKER

905 SOUTH BLVD EAST

ROCHESTER HILLS, MI 48307

TEL: (248) 844-5400

FOOD SERVICE:

BAKERGROUP

2220 EAST PARIS AVE. SE

GRAND RAPIDS, MI 49546

TEL. 1(800) 968-4011

/2

/2

:5 :0

P

M

C

U s e rs

\r s in g h \D o c u m e n ts

\L S

D H ill C e n te r S u m m e r

R e m o d e l_

A rc h r2 rs in g h P

P C

T

.r v t

2612.03

TITLE SHEET

G0.1

W ise

R d.

L an sin g, M I 4

La ns in g

S ch o o l D is tr ic t

H il l C e n te r S u m m e r

R e n o v a ti o n s

Lansing School District

Hill Center Summer 2025 Renovations

SHEET INDEX:

CONSTRUCTION DOCUMENTS - ADDENDUM 01

FEBRUARY 26, 2025

NO. NAME

GENERAL

G0.1 TITLE SHEET

G0.2 DATA SHEET

CIVIL

C1.0 TOPOGRAPHICAL SURVEY

C1.1 DEMOLITION PLAN

C1.2 SOIL EROSION AND SEDIMENTATION CONTROL PLAN

C2.1 PAVING AND LAYOUT PLAN

C3.1 GRADING PLAN

L1.0 LANDSCAPE PLAN

STRUCTURAL

S0.1 STRUCTURAL NOTES

S1.0 FRAMING PLANS, SECTIONS, AND DETAILS

ARCHITECTURAL

A0.1 FIRST FLOOR COMPOSITE PLAN

A0.2 SECOND FLOOR COMPOSITE PLAN

A0.3 FIRST FLOOR CODE COMPLIANCE PLAN

A0.4 SECOND FLOOR CODE COMPLIANCE PLAN

A0.5 PARTIAL ROOF PLAN

D1.1 FIRST FLOOR DEMOLITION PLAN - UNIT 100

D1.2 FIRST FLOOR DEMOLITION PLAN - UNIT 200

D1.2B FIRST FLOOR DEMOLITION PLAN - UNIT 200B

D1.3 FIRST FLOOR DEMOLITION PLAN - UNIT 300

D1.11 ADD ALT - SECOND FLOOR DEMOLITION PLAN - UNIT 100

D1.14 ADD ALT - SECOND FLOOR DEMOLITION PLAN - UNIT 400

D2.11 FIRST FLOOR REFLECTED CEILING DEMOLITION PLAN - UNIT 100

D2.12B FIRST FLOOR REFLECTED CELING DEMOLITION PLAN - UNIT

200B

D2.12 FIRST FLOOR REFLECTED CEILING DEMOLITION PLAN - UNIT

D2.13 FIRST FLOOR REFLECTED CEILING DEMOLITION PLAN - UNIT 300

D2.21 ADD ALT - SECOND FLOOR REFLECTED CEILING DEMOLITION

PLAN - UNIT 100

D2.24 ADD ALT - SECOND FLOOR REFLECTED CEILING DEMOLITION

PLAN - UNIT 400

A1.1 FIRST FLOOR PLAN - UNIT 100

A1.2 FIRST FLOOR PLAN - UNIT 200

A1.2B FIRST FLOOR PLAN - UNIT 200B

A1.3 FIRST FLOOR PLAN - UNIT 300

A1.11 ADD ALT - SECOND FLOOR PLAN - UNIT 100

A1.14 ADD ALT - SECOND FLOOR PLAN - UNIT 400

A1.22 FIRST FLOOR EQUIPMENT PLAN - UNIT 200

A1.31 SECOND FLOOR EQUIPMENT PLAN - UNIT 100

BASE BID: DEMOLITON AND NEW WORK AS SHOWN ON FIRST FLOOR:

1. ENTRY

2. CORRIDOR 100K

3. KITCHEN B104E

4. WELCOME SUITE 200-204

ROOF REPAIR AS SHOWN ABOVE ENTRY USING EXISTING ROOF DRAINS.

EXTERIOR METAL PANEL INSTALLATION ON FACADE WITH CANOPY ABOVE DOOR 200.

SITE RE-WORK AT ENTRY AS SHOWN ON DRAWINGS.

ADD ALTERNATE 1: DEMOLITION AND NEW WORK AS SHOWN ON SECOND FLOOR ROOMS:

1A. CLASSROOM C210, CLASSROOM C211& OFFICE C211B

1B. TEACHERS LOUNGE D209 & CLASSROOM D210

1C. CLASSROOM D215 & CLASSROOM D216

ADD ALTERNATE 2: REPLACE EXISTING ROOF DRAINS WITH NEW ROOF DRAINS WITH OVERFLOWS AT

AREA OF WORK ABOVE ENTRY.

NO. NAME

A1.34 SECOND FLOOR EQUIPMENT PLAN - UNIT 400

A1.35 EQUIPMENT DETAILS

A1.36 CASEWORK SCHEDULE AND SPECIFICATIONS

A2.1 FIRST FLOOR REFLECTED CEILING PLAN - UNIT 100

A2.2 FIRST FLOOR REFLECTED CEILING PLAN - UNIT 200

A2.2B FIRST FLOOR REFLECTED CEILING PLAN - UNIT 200B

A2.3 FIRST FLOOR REFLECTED CEILING PLAN - UNIT 300

A2.11 SECOND FLOOR REFLECTED CEILING PLAN - UNIT 100

A2.14 SECOND FLOOR REFLECTED CEILING PLAN - UNIT 400

A2.30 INTERIOR PARTITION TYPES

A3.1 EXTERIOR ELEVATIONS

A3.3 BUILDING SECTIONS

A5.1 BUILDING DETAILS

A5.2 BUILDING DETAILS

A6.1 DOOR SCHEDULE

A6.2 DOOR & WINDOW DETAILS

A6.3 DOOR HARDWARE SCHEDULE

A8.1 FIRST FLOOR COLOR LAYOUT PLAN - UNIT 100

A8.2 FIRST FLOOR COLOR LAYOUT PLAN - UNIT 200

A8.2B FIRST FLOOR COLOR LAYOUT PLAN - UNIT 200B

A8.3 FIRST FLOOR COLOR LAYOUT PLAN - UNIT 300

A8.11 ADD ALT - SECOND FLOOR COLOR LAYOUT PLAN - UNIT 100

A8.14 ADD ALT - SECOND FLOOR COLOR LAYOUT PLAN - UNIT 400

A9.1 INTERIOR ELEVATIONS

A9.2 INTERIOR ELEVATIONS & DETAILS

A9.3 INTERIOR RENDERINGS

FOOD SERVICE

FS1.1 FOODSERVICE EQUIPMENT PLAN

FS2.1 FOODSERVICE PLUMBING/MECHANICAL PLAN

FS3.1 FOODSERVICE ELECTRICAL PLAN

FS6.1 VENTILATION HOOD SHEETS

FS6.2 VENTILATION HOOD SHEETS

FS6.3 VENTILATION HOOD SHEETS

FS6.4 VENTILATION HOOD SHEETS

FS6.5 VENTILATION HOOD SHEETS

FS6.6 VENTILATION HOOD SHEETS

MECHANICAL

M0.0 MECHANICAL GENERAL INFORMATION

PD1.3 FIRST FLOOR PLUMBING DEMOLITION PLAN - UNIT 300

MD1.2 FIRST FLOOR COMB. MECH./PLUMB. DEMOLITION PLAN - UNIT

MD1.2B FIRST FLOOR MECHANICAL DEMOLITION PLAN - UNIT 200B

NO. NAME

MD1.3 FIRST FLOOR MECHANICAL DEMOLITION PLAN - UNIT 300

MD1.11 SECOND FLOOR COMBO. MECH./PLUMB. DEMOLITION PLAN -

UNIT 100

MD1.12 SECOND FLOOR COMB. MECH./PLUMB. DEMOLITION PLAN - UNIT

MD1.14 SECOND FLOOR COMBO. MECH./PLUMB. DEMOLITION PLAN -

UNIT 400

FP1.0 FIRE PROTECTION PLANS

P1.3UG UNDERGROUND PLUMBING PLAN - UNIT 300

P1.3 FIRST FLOOR PLUMBING PLAN - UNIT 300

P4.0 ENLARGED PLUMBING PLANS

M1.1 FIRST FLOOR MECHANICAL PLAN - UNIT 100

M1.2 FIRST FLOOR MECHANICAL PLAN - UNIT 200

M1.2B FIRST FLOOR COMB. MECH./PLUMB. PLAN - UNIT 200B

M1.3 FIRST FLOOR MECHANICAL PLAN - UNIT 300

M1.11 SECOND FLOOR COMB. MECH./PLUMB. PLAN - UNIT 100

M1.12 SECOND FLOOR COMBO. MECH./PLUMB. PLAN - UNIT 200

M1.14 SECOND FLOOR COMB. MECH./PLUMB. PLAN - UNIT 400

M1.R ROOF COMBO. MECH.LPLUMB. PARTIAL PLAN - UNIT 200/300

M5.0 MECHANICAL DETAILS & DIAGRAMS

M6.0 MECHANICAL SCHEDULES

M8.0 TEMPERATURE CONTROLS

M9.0 MECHANICAL SPECIFICATIONS

M9.1 MECHANICAL SPECIFICATIONS

ELECTRICAL

E0.0 ELECTRICAL GENERAL INFORMATION

E0.1 ELECTRICAL SCHEDULES & DETAILS

ED1.2 FIRST FLOOR ELECTRICAL DEMOLITION PLAN - UNIT 200

ED1.2B FIRST FLOOR ELECTRICAL DEMOLITION PLAN - UNIT 200B

ED1.3 FIRST FLOOR ELECTRICAL DEMOLITION PLAN - UNIT 300

ED1.11 SECOND FLOOR ELECTRICAL DEMOLITION PLAN - UNIT 100

ED1.14 SECOND FLOOR ELECTRICAL DEMOLITION PLAN - UNIT 400

EP1.2 FIRST FLOOR POWER PLAN - UNIT 200

EP1.2B FIRST FLOOR POWER PLAN - UNIT 200B

EP1.3 FIRST FLOOR POWER PLAN - UNIT 300

EP1.11 SECOND FLOOR POWER PLAN - UNIT 100

EP1.14 SECOND FLOOR POWER PLAN - UNIT 400

EP1.3R PARTIAL ROOF POWER PLAN

EL1.2 FIRST FLOOR LIGHTING PLAN - UNIT 200

EL1.2B FIRST FLOOR LIGHTING PLAN - UNIT 200B

EL1.3 FIRST FLOOR LIGHTING PLAN - UNIT 300

EL1.11 SECOND FLOOR LIGHTING PLAN - UNIT 100

EL1.14 SECOND FLOOR LIGHTING PLAN - UNIT 400

E9.0 ELECTRICAL SPECIFICATIONS

E9.1 ELECTRICAL SPECIFICATIONS

CONSTRUCTION DOCUMENTS 02/07/2025

ADDENDUM 01 02/26/2025

TAX PARCEL No.

33-01-05-06-401-003

HILL CENTER

LANSING PUBLIC SCHOOLS

HILL CENTER

#5815 WISE RD.

1 STORY BRICK BLDG.

JOB NO.

SHEET TITLE

SHEET NO.

REVISIONS/REVIEW

KEY PLAN

DATE

NORTH

R en o va tio ns

KALAMAZOO | CHELSEA | GRAND RAPIDS | ROYAL OAK

La ns in g

Sc ho ol D ist ric t

KEY PLAN

TH

ES

E D

R

AW

IN

G

S

AN

D T

H E

W O

R K

R

EP

R

ES

EN

TE

D T

H

ER

EI

N

A R

E

TH

E

PR

O

PE

R

TY

O F

AN

D

C O

PY

R

IG

H

T

KI

N G

SC

O

TT

A

SS

O

C

IA

TE

S

A N

D M

AY

N

O T

BE

U

SE

D

O R

R

EP

R O

D U

C

ED

W

IT

H O

U T

PE

R

M

IS

SI

O

N

LA

ST

P R

IN

TE

D

W ise

R d.

L an sin g, M I 4

H ill

C en te r

Su m m er

CONSTRUCTION DOCUMENTS 02/07/2025

ADDENDUM 01 02/26/2025

GRAPHIC SCALE

L1.0

LANDSCAPE PLAN

LANDSCAPE NOTES:

SEEDING NOTES:

PLANT SCHEDULE

LEGEND

DETAILDETAIL

SHRUB PLANTING L1.0

SHRDETAILDETAIL

PERENNIAL / ORNAMENTAL GRASS PLANTINGL1.0

PER

AutoCAD SHX Text

ELEC. SIGN

AutoCAD SHX Text

10"ST

AutoCAD SHX Text

10"ST

AutoCAD SHX Text

12"ST

AutoCAD SHX Text

GRASS

AutoCAD SHX Text

GRASS

AutoCAD SHX Text

GRASS

AutoCAD SHX Text

GRASS

AutoCAD SHX Text

GRASS

AutoCAD SHX Text

GRASS

AutoCAD SHX Text

GRASS

AutoCAD SHX Text

ASPH

AutoCAD SHX Text

OVHG

AutoCAD SHX Text

OVHG

AutoCAD SHX Text

OVHG

AutoCAD SHX Text

PLANTER

AutoCAD SHX Text

GRASS

AutoCAD SHX Text

CONC

AutoCAD SHX Text

6" CONC. CURB

AutoCAD SHX Text

6" CONC. CURB

AutoCAD SHX Text

SIGN

AutoCAD SHX Text

2' MIN. DIA. BOULDER TYP.

AutoCAD SHX Text

MULCHED PLANTING BED

AutoCAD SHX Text

MULCHED PLANTING BED

AutoCAD SHX Text

LIMITS OF 12" PLANTING MIX

AutoCAD SHX Text

KINGSCOTT ASSOCIATES INC. KALAMAZOO, MICHIGAN

AutoCAD SHX Text C

AutoCAD SHX Text 2612.03

AutoCAD SHX Text C

AutoCAD SHX Text

( IN FEET )

AutoCAD SHX Text 1 inch = 30 ft.

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

AutoCAD SHX Text

1. INSTALL 3" X 12 GA. EDGING TO SEPARATE LAWN FROM PLANTING BED. INSTALL 3" X 12 GA. EDGING TO SEPARATE LAWN FROM PLANTING BED. 2. INSTALL 3" DEEP SHREDDED BARK MULCH TO ALL PLANTING AREAS / BEDS INSTALL 3" DEEP SHREDDED BARK MULCH TO ALL PLANTING AREAS / BEDS 2.1. MULCH SHALL BE COLORIZED WITH MULCH MAGIC-ESPRESSO COLOR, AVAILABLE FROM SUPERIOR GROUNDCOVER OR MULCH SHALL BE COLORIZED WITH MULCH MAGIC-ESPRESSO COLOR, AVAILABLE FROM SUPERIOR GROUNDCOVER OR APPROVED EQUAL. 3. CONTRACTOR SHALL VERIFY THE LOCATION OF ALL UNDERGROUND UTILITIES, PIPES AND STRUCTURES, AS WELL AS THE CONTRACTOR SHALL VERIFY THE LOCATION OF ALL UNDERGROUND UTILITIES, PIPES AND STRUCTURES, AS WELL AS THE LOCATION OF EXISTING TREES AND VEGETATION. CONTRACTOR SHALL BE RESPONSIBLE FOR ANY COST INCURRED DUE TO DAMAGE/REMOVAL OF SAID ELEMENTS. 4. ANY DISCREPANCIES BETWEEN PLANS, NOTES, DETAILS AND EXISTING CONDITIONS SHALL BE IMMEDIATELY REPORTED TO THE ANY DISCREPANCIES BETWEEN PLANS, NOTES, DETAILS AND EXISTING CONDITIONS SHALL BE IMMEDIATELY REPORTED TO THE OWNER'S AUTHORIZED REPRESENTATIVE FOR REVIEW AND DECISION. CONTRACTOR SHALL ASSUME FULL RESPONSIBILITY FOR ALL REVISIONS DUE TO FAILURE TO GIVE SUCH NOTIFICATION. 5. CONTRACTOR IS RESPONSIBLE FOR ANY DAMAGE TO EXISTING MATERIALS/IMPROVEMENTS, DAMAGED DURING CONSTRUCTION. CONTRACTOR IS RESPONSIBLE FOR ANY DAMAGE TO EXISTING MATERIALS/IMPROVEMENTS, DAMAGED DURING CONSTRUCTION. 6. SITE BOUNDARY, TOPOGRAPHY, UTILITIES AND OTHER BASE INFORMATION PROVIDED BY OTHERS. SITE BOUNDARY, TOPOGRAPHY, UTILITIES AND OTHER BASE INFORMATION PROVIDED BY OTHERS. 7. CONTRACTOR SHALL VERIFY QUANTITIES SHOWN ON PLANT SCHEDULES AND THOSE INDICATED ON PLANS. CONTRACTOR IS CONTRACTOR SHALL VERIFY QUANTITIES SHOWN ON PLANT SCHEDULES AND THOSE INDICATED ON PLANS. CONTRACTOR IS RESPONSIBLE FOR INSTALLATION OF QUANTITIES DRAWN. 8. CONTRACTOR SHALL MAKE MINOR ADJUSTMENTS TO PLANT MATERIAL LOCATIONS IN FIELD, AS NECESSARY. THE LOCATION OF CONTRACTOR SHALL MAKE MINOR ADJUSTMENTS TO PLANT MATERIAL LOCATIONS IN FIELD, AS NECESSARY. THE LOCATION OF ALL PLANT MATERIAL SHALL BE SUBJECT TO APPROVAL BY THE OWNER'S AUTHORIZED REPRESENTATIVE. 9. ALL PLANT MATERIAL SHALL BE OF THE SIZES CALLED FOR IN THE PLANT SCHEDULES. ANY PLANT MATERIAL NOT MEETING THE ALL PLANT MATERIAL SHALL BE OF THE SIZES CALLED FOR IN THE PLANT SCHEDULES. ANY PLANT MATERIAL NOT MEETING THE SIZED AND/OR QUALITY AS CALLED FOR SHALL BE REMOVED FROM SITE. ALL TREES SHALL BE INSPECTED AND APPROVED BY THE OWNER'S AUTHORIZED REPRESENTATIVE. NO SUBSTITUTIONS OF PLANT MATERIAL SHALL BE MADE WITHOUT APPROVAL FROM THE OWNER'S AUTHORIZED REPRESENTATIVE. 10. CONTRACTOR SHALL DETERMINE APPROPRIATE PLANTING BACKFILL MIXES (BASED ON SOILS/SUBSURFACE CONDITIONS) AND CONTRACTOR SHALL DETERMINE APPROPRIATE PLANTING BACKFILL MIXES (BASED ON SOILS/SUBSURFACE CONDITIONS) AND REVIEW ALTERNATIVES WITH OWNER'S AUTHORIZED REPRESENTATIVE PRIOR TO INSTALLATION. 11. CONTRACTORTO INCLUDE COST OF ALL MULCH IN THE COST OF THE PLANT MATERIAL. CONTRACTORTO INCLUDE COST OF ALL MULCH IN THE COST OF THE PLANT MATERIAL.

AutoCAD SHX Text

1. SEED ALL NON NATIVE DISTURBED AREAS UNLESS OTHERWISE NOTED WITH: EARTH CARPET QUICK TO GROW LAWN SEED MIXTURE 25% PERENNIAL RYEGRASS 25% KENTUCKY BLUEGRASS 25% ANNUAL RYEGRASS 25% CREEPING RED FESCUE APPLY AT THE RATE OF 5-6 POUNDS PER 1,000SF 2. MULCH BLANKETS SHALL BE USED IN ALL AREAS WITH 10% OR GREATER SLOPE.

AutoCAD SHX Text Qty.

AutoCAD SHX Text

ID

AutoCAD SHX Text Botanical Name

AutoCAD SHX Text Common Name

AutoCAD SHX Text Size

AutoCAD SHX Text Description

AutoCAD SHX Text

AutoCAD SHX Text

CA

AutoCAD SHX Text

CALAMAGROSTIS × ACUTIFLORA 'KARL FOERSTER'ACUTIFLORA 'KARL FOERSTER'

AutoCAD SHX Text

FEATHER READ GRASS

AutoCAD SHX Text

NO 1 CONT.

AutoCAD SHX Text

AutoCAD SHX Text

LM

AutoCAD SHX Text

LIRIOPE MUSCARI 'SILVERY SUNPROOF'

AutoCAD SHX Text

SILVERY SUNPROOF LILYTURF

AutoCAD SHX Text

NO 1 CONT.

AutoCAD SHX Text

AutoCAD SHX Text

PA

AutoCAD SHX Text

PENNISETUM ALOPECUROIDES 'HAMELN'

AutoCAD SHX Text

DWARF FOUNTAIN GRASS

AutoCAD SHX Text

NO 1 CONT.

AutoCAD SHX Text

AutoCAD SHX Text

VC

AutoCAD SHX Text

VIBURNUM CARLESII

AutoCAD SHX Text

KOREAN SPICE VIBURNUM

AutoCAD SHX Text

NO 5 CONT.

AutoCAD SHX Text

AutoCAD SHX Text

WF

AutoCAD SHX Text

WEIGELA FLORIDA 'FINE WINE'

AutoCAD SHX Text

FINE WINE WEIGELA

AutoCAD SHX Text

NO 5 CONT.

AutoCAD SHX Text

AutoCAD SHX Text

2' MINIMUM DIAMETER BOULDERS

AutoCAD SHX Text

PLANT TYPE

AutoCAD SHX Text

QUANTITY

AutoCAD SHX Text BEFORE BACKFILLING AROUND PLANT REMOVE ALL PLASTIC BALLING MATERIAL AND METAL CONTAINERS. PUNCH HOLES IN FIBER POTS TO PROVIDE DRAINAGE

AutoCAD SHX Text

UNDISTURBED SUBGRADE: SCARIFY TO 1'' DEPTH

AutoCAD SHX Text

FINISH GRADE

AutoCAD SHX Text

6'' MINIMUM PLANTING MIXTURE BETWEEN BALL AND PIT WALL

AutoCAD SHX Text

IN SODDED AREAS PLACE SOD TO BOTTOM OF EARTH SAUCER

AutoCAD SHX Text

SAUCER 3'' DEEP

AutoCAD SHX Text

REMOVE BURLAP, ROPES AND WIRE FROM TOP 1/3 OF BALL

AutoCAD SHX Text

MULCH 3'' DEEP INSIDE SAUCER, SEE NOTE 2.1 FOR COLOR

AutoCAD SHX Text

12" DEEP BED WITH SPECIFIED PLANTING MIX.

AutoCAD SHX Text

MULCH, 3" DEEP SEE NOTE 2.1 FOR COLOR

AutoCAD SHX Text

TURF GRASS

AutoCAD SHX Text REMOVE PLANT FROM POT (EVEN FIBER POTS) AND BREAK UP ANY ROOT KNOTS THAT MAY BE AT THE BOTTOM OF THE ROOT BALL

AutoCAD SHX Text

ADD-01

T ie r

SHOP

CLASSROOM

C136A

SHOP

CLASSROOM

C136B

UNIT 100UNIT 200

UNIT 300 UNIT 400

VEST

TOILET

C103

NURSE

PRINCIPAL

NURSE

WELCOME

KITCHEN

B104E

CORRIDOR

100K

CLASSROOM

150OFFICE

UNIT 200B

REMODELED AREA

UNAFFECTED EXISTING AREA

* SHOWN FOR GENERAL ORIENTATION / REFERENCE ONLY

INDICATES CONSTRUCTION DOCUMENT ROOM NUMBERS.

REFER TO CODE COMPLIANCE SHEETS FOR BUILDING CODE REQUIREMENTS.

NAME

COMPOSITE PLAN GENERAL NOTES

KINGSCOTT ASSOCIATES INC. KALAMAZOO, MICHIGANCC

JOB NO.

SHEET TITLE

SHEET NO.

ISSUANCES DATE

N

KEY PLAN

P L

E A

S E

R E

C Y

C L

E

T H

E S

E D

R A

W

IN

G S

A N

D T

H E

W O

R K

R E

P R

E S

E N

T E

D T

H E

R E

IN

A

R E

T H

E P

R O

P E

R T

Y O

F A

P

Y R

IG

H

T

K

IN

G

S C

O T

T A

S S

O C

IA

T

D

M A

Y N

O T

B E

U S

E D

O R

R E

P R

O D

U C

H

O U

T P

E R

M

IS

S

IO

N

L A

S T

P R

IN

T

E D ljh

KALAMAZOO | CHELSEA | GRAND RAPIDS | ROYAL OAK

/2

/2

:5 :0

P

M

C

U s e rs

\r s in g h \D o c u m e n ts

\L S

D H ill C e n te r S u m m e r

R e m o d e l_

A rc h r2 rs in g h P

P C

T

.r v t

2612.03

FIRST FLOOR COMPOSITE PLAN

A0.1

W ise

R d.

L an sin g, M I 4

La ns in g

S ch o o l D is tr ic t

H il l C e n te r S u m m e r

R e n o v a ti o n s

1/16" = 1'-0"

FIRST FLOOR COMPOSITE PLANFIRST FLOOR COMPOSITE PLAN

UP

DEMOLITION PLAN GENERAL NOTES

1. CONTRACTOR IS RESPONSIBLE TO COORDINATE WITH ALL OTHER DRAWINGS AND

SPECIFICATIONS FOR ADDITIONAL AREAS THAT WILL REQUIRE DEMOLITION NOT INDICATED

ON THESE SHEETS.

2. THE DEMOLITION PLANS GENERALLY INDICATE AREAS OF EXTENSIVE REMOVALS AND DO

NOT INDICATE ALL OF THE WORK. CONTRACTOR SHALL PERFORM ALL DEMOLITION WHICH

IS NECESSARY FOR THE PROPER EXECUTION OF THE PROJECT WHETHER OR NOT SAID

DEMOLITION IS SPECIFICALLY INDICATED WITHIN THE DOCUMENTS.

3. CONTRACTOR IS RESPONSIBLE TO INFILL, PATCH AND/ OR REPAIR, EXISTING WALL, FLOORS

AND CEILINGS TO MATCH EXISTING WHERE DEMOLITION OCCURS OTHER THAN AS DESCRIBED

IN THESE DOCUMENTS.

4. IT IS THE INTENTION OF THESE DOCUMENTS THAT THE DEMOLITION OF PORTIONS OF

MASONRY WALLS (BOTH INTERIOR AND EXTERIOR) ARE GENERALLY TO BE DONE ALONG

JOINT AND COURSING LINES.

5. PATCH AND REPAIR REMAINING ADJACENT SURFACES AT AREAS OF REMOVAL AND/ OR

ALTERATION TO MATCH EXISTING. PROVIDE A SOUND AND PROPER SUBSTRATE FOR NEW

FINISH. COORDINATE WITH COLOR PLANS. WHERE A NEW FINISH IS NOT INDICATED, MATCH

EXISTING ADJACENT FINISHES.

6. ALL DEMOLITION IS TO BE DONE WITH REASONABLE CARE AS TO MINIMIZE DAMAGE TO

EXISTING REMAINING SURFACES. CONTRACTOR IS RESPONSIBLE TO PROPERLY DISPOSE OF

ALL DEMOLISHED ITEMS NOT INDICATED TO BE RELOCATED OR TURNED OVER TO OWNER.

7. REMOVE AND TURN OVER TO OWNER ALL FIRE EXTINGUISHERS AND CABINETS AT AREAS TO

BE DEMOLISHED, IF NOT OTHERWISE INDICATED TO BE RELOCATED.

8. CLEAN AND PREPARE ALL EXISTING SURFACES WHICH ARE TO BE PAINTED/ PATCHED.

PREPARATION TO INCLUDE MINOR PATCHING.

9. COORDINATE WITH MECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS FOR FURTHER

DEMOLITION NOTES.

DEMOLITION PLAN KEYNOTES

FLOORS

A. PREP EXISTING CONCRETE FLOOR FOR NEW FLOOR.

B. REMOVE AND DISPOSE OF ALL FLOORING AND BASE. PREP REMAINING SURFACES TO

RECEIVE NEW FINISH. VERIFY EXISTING FLOORING EXTENTS IN FIELD.

C. REMOVE AND DISPOSE OF WALK-OFF CARPET.

D. REMOVE AND DISPOSE OF CONCRETE CURB.

WALLS

A. REMOVE STORE FRONT WALL CONSTRUCTION, FRAMING, AND ALL ANCHORS AND

SUPPORTS. PREP REMAINING SURFACES TO RECEIVE NEW FINISHES AND/OR CONSTRUCTION.

B. REMOVE AND DISPOSE MASONRY WALL CONSTRUCTION AND ALL RELATED

BRACING/SUPPORTS. PREP REMAINING SURFACES TO RECEIVE NEW FINISHES AND/OR

CONSTRUCTION. REFER TO STRUCTURAL FOR LINTEL.

C. REMOVE WINDOW WITHIN WALL, FRAMING, AND ALL ANCHORS AND SUPPORTS. PREP

REMAINING SURFACES TO RECEIVE NEW FINISHES AND/OR CONSTRUCTION.

D. REMOVE GYPSUM BOARD WALL CONSTRUCTION, FRAMING, AND ALL ANCHORS AND

SUPPORTS. PREP REMAINING SURFACES TO RECEIVE NEW FINISHES AND/OR CONSTRUCTION

E. REMOVE AND DISPOSE OF MASONRY CURB. PREP SURFACES TO RECEIVE NEW FINISHES

AND/OR CONSTRUCTION.

DOORS

A. REMOVE AND DISPOSE OF EXTERIOR DOOR, INCLUDING FRAME, SIDELIGHTS, TRANSOMS

AND ALL RELATED ANCHORS AND SUPPORTS. SAWCUT ALL FRAME ANCHORS - PRYING

ANCHORS FROM SUBSTRATES IS UNACCEPTABLE. SALVAGE HARDWARE & RETURN TO

OWNER.

B. REMOVE AND DISPOSE OF INTERIOR DOOR, INCLUDING FRAME, SIDELIGHTS AND ALL

RELATED ANCHORS AND SUPPORTS. SAWCUT ALL FRAME ANCHORS - PRYING ANCHORS

FROM SUBSTRATES IS UNACCEPTABLE. SALVAGE HARDWARE & RETURN TO OWNER.

C. REMOVE AND DISPOSE OF PARTITION WALL AND DOOR. PREP REMAINING SURFACES TO

RECEIVE NEW FINISHES AND/OR CONSTRUCTION.

D. REMOVE DOOR KNOB, RETURN TO OWNER.

CASEWORK

A. REMOVE AND DISPOSE OF COUNTERTOP. PREP REMAINING SURFACES TO RECEIVE NEW

FINISHES AND/OR CONSTRUCTION.

B. REMOVE AND SALVAGE BENCH. RETURN TO OWNER. PREP REMAINING SURFACES TO

RECEIVE NEW FINISHES AND/OR CONSTRUCTION

C. REMOVE AND DISPOSE OF COUNTERTOP AND ALL UPPER/BASE CABINETS. PREP REMAINING

SURFACES TO RECEIVE NEW FINISHES AND/OR CONSTRUCTION.

D. REMOVE METAL LOCKERS AND ALL RELATED ANCHORS, SUPPORTS, HARDWARE AND

ADHESIVES. RETURN TO OWNER.

TOILETS/PLUMBING

A. REMOVE AND DISPOSE OF PLUMBING FIXTURE - REFER TO PLUMBING DEMOLITION PLANS.

PREP REMAINING SURFACES TO RECEIVE NEW CONSTRUCTION AND/OR FINISHES.

B. REMOVE ACCESSORIES INCLUDING HAND DRYERS, PAPER TOWEL DISPENSERS, TOILET

PAPER DISPENSERS, SOAP DISPENSERS AND ALL RELATED ANCHORS, SUPPORTS,

HARDWARE AND ADHESIVES. RETURN TO OWNER.

MISCELLANEOUS

A. REMOVE AND DISPOSE OF MECHANICAL EQUIPMENT. REFER TO MECHANICAL DEMOLITION

PLANS.

B. REMOVE AND DISPOSE OF APPROXIMATELY 2,060 SQ. FT. OF EXISTING ROOF SYSTEM

DOWN TO CONCRETE ROOF DECK, ROOF DRAINS TO REMAIN.

C. REMOVE AND DISPOSE OF KITCHEN EQUIPMENT. REFER TO FOOD SERVICE DEMOLITION

PLANS.

3A 3A2A

4B

4B

3B3B3B 3C 2C

2A

2A

2A

2A

2A

2A

3C

3C2B

5A

4A

6A

1A

1A

1C

3D

2E 5B

3B

KINGSCOTT ASSOCIATES INC. KALAMAZOO, MICHIGANCC

JOB NO.

SHEET TITLE

SHEET NO.

ISSUANCES DATE

N

KEY PLAN

P L

E A

S E

R E

C Y

C L

E

T H

E S

E D

R A

W

IN

G S

A N

D T

H E

W O

R K

R E

P R

E S

E N

T E

D T

H E

R E

IN

A

R E

T H

E P

R O

P E

R T

Y O

F A

P

Y R

IG

H

T

K

IN

G

S C

O T

T A

S S

O C

IA

T

D

M A

Y N

O T

B E

U S

E D

O R

R E

P R

O D

U C

H

O U

T P

E R

M

IS

S

IO

N

L A

S T

P R

IN

T

E D ljh

KALAMAZOO | CHELSEA | GRAND RAPIDS | ROYAL OAK

/2

/2

:5 :0

P

M

C

U s e rs

\r s in g h \D o c u m e n ts

\L S

D H ill C e n te r S u m m e r

R e m o d e l_

A rc h r2 rs in g h P

P C

T

.r v t

2612.03

FIRST FLOOR DEMOLITION PLAN -

UNIT 200

D1.2

W ise

R d.

L an sin g, M I 4

La ns in g

S ch o o l D is tr ic t

H il l C e n te r S u m m e r

R e n o v a ti o n s

1/8" = 1'-0"1

FIRST FLOOR DEMOLITION PLAN - UNIT 200FIRST FLOOR DEMOLITION PLAN - UNIT 200

1. CONTRACTOR IS RESPONSIBLE TO COORDINATE WITH ALL OTHER DRAWINGS AND

SPECIFICATIONS FOR ADDITIONAL AREAS THAT WILL REQUIRE DEMOLITION NOT INDICATED

ON THESE SHEETS.

2. THE DEMOLITION PLANS GENERALLY INDICATE AREAS OF EXTENSIVE REMOVALS AND DO

NOT INDICATE ALL OF THE WORK. CONTRACTOR SHALL PERFORM ALL DEMOLITION WHICH

IS NECESSARY FOR THE PROPER EXECUTION OF THE PROJECT WHETHER OR NOT SAID

DEMOLITION IS SPECIFICALLY INDICATED WITHIN THE DOCUMENTS.

3. CONTRACTOR IS RESPONSIBLE TO INFILL, PATCH AND/ OR REPAIR, EXISTING WALL, FLOORS

AND CEILINGS TO MATCH EXISTING WHERE DEMOLITION OCCURS OTHER THAN AS DESCRIBED

IN THESE DOCUMENTS.

4. IT IS THE INTENTION OF THESE DOCUMENTS THAT THE DEMOLITION OF PORTIONS OF

MASONRY WALLS (BOTH INTERIOR AND EXTERIOR) ARE GENERALLY TO BE DONE ALONG

JOINT AND COURSING LINES.

5. PATCH AND REPAIR REMAINING ADJACENT SURFACES AT AREAS OF REMOVAL AND/ OR

ALTERATION TO MATCH EXISTING. PROVIDE A SOUND AND PROPER SUBSTRATE FOR NEW

FINISH. COORDINATE WITH COLOR PLANS. WHERE A NEW FINISH IS NOT INDICATED, MATCH

EXISTING ADJACENT FINISHES.

6. ALL DEMOLITION IS TO BE DONE WITH REASONABLE CARE AS TO MINIMIZE DAMAGE TO

EXISTING REMAINING SURFACES. CONTRACTOR IS RESPONSIBLE TO PROPERLY DISPOSE OF

ALL DEMOLISHED ITEMS NOT INDICATED TO BE RELOCATED OR TURNED OVER TO OWNER.

7. REMOVE AND TURN OVER TO OWNER ALL FIRE EXTINGUISHERS AND CABINETS AT AREAS TO

BE DEMOLISHED, IF NOT OTHERWISE INDICATED TO BE RELOCATED.

8. CLEAN AND PREPARE ALL EXISTING SURFACES WHICH ARE TO BE PAINTED/ PATCHED.

PREPARATION TO INCLUDE MINOR PATCHING.

9. COORDINATE WITH MECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS FOR FURTHER

DEMOLITION NOTES.

DEMOLITION PLAN KEYNOTES

FLOORS

A. PREP EXISTING CONCRETE FLOOR FOR NEW FLOOR.

B. REMOVE AND DISPOSE OF ALL FLOORING AND BASE. PREP REMAINING SURFACES TO

RECEIVE NEW FINISH. VERIFY EXISTING FLOORING EXTENTS IN FIELD.

C. REMOVE AND DISPOSE OF WALK-OFF CARPET.

D. REMOVE AND DISPOSE OF CONCRETE CURB.

WALLS

A. REMOVE STORE FRONT WALL CONSTRUCTION, FRAMING, AND ALL ANCHORS AND

SUPPORTS. PREP REMAINING SURFACES TO RECEIVE NEW FINISHES AND/OR CONSTRUCTION.

B. REMOVE AND DISPOSE MASONRY WALL CONSTRUCTION AND ALL RELATED

BRACING/SUPPORTS. PREP REMAINING SURFACES TO RECEIVE NEW FINISHES AND/OR

CONSTRUCTION. REFER TO STRUCTURAL FOR LINTEL.

C. REMOVE WINDOW WITHIN WALL, FRAMING, AND ALL ANCHORS AND SUPPORTS. PREP

REMAINING SURFACES TO RECEIVE NEW FINISHES AND/OR CONSTRUCTION.

D. REMOVE GYPSUM BOARD WALL CONSTRUCTION, FRAMING, AND ALL ANCHORS AND

SUPPORTS. PREP REMAINING SURFACES TO RECEIVE NEW FINISHES AND/OR CONSTRUCTION

E. REMOVE AND DISPOSE OF MASONRY CURB. PREP SURFACES TO RECEIVE NEW FINISHES

AND/OR CONSTRUCTION.

DOORS

A. REMOVE AND DISPOSE OF EXTERIOR DOOR, INCLUDING FRAME, SIDELIGHTS, TRANSOMS

AND ALL RELATED ANCHORS AND SUPPORTS. SAWCUT ALL FRAME ANCHORS - PRYING

ANCHORS FROM SUBSTRATES IS UNACCEPTABLE. SALVAGE HARDWARE & RETURN TO

OWNER.

B. REMOVE AND DISPOSE OF INTERIOR DOOR, INCLUDING FRAME, SIDELIGHTS AND ALL

RELATED ANCHORS AND SUPPORTS. SAWCUT ALL FRAME ANCHORS - PRYING ANCHORS

FROM SUBSTRATES IS UNACCEPTABLE. SALVAGE HARDWARE & RETURN TO OWNER.

C. REMOVE AND DISPOSE OF PARTITION WALL AND DOOR. PREP REMAINING SURFACES TO

RECEIVE NEW FINISHES AND/OR CONSTRUCTION.

D. REMOVE DOOR KNOB, RETURN TO OWNER.

CASEWORK

A. REMOVE AND DISPOSE OF COUNTERTOP. PREP REMAINING SURFACES TO RECEIVE NEW

FINISHES AND/OR CONSTRUCTION.

B. REMOVE AND SALVAGE BENCH. RETURN TO OWNER. PREP REMAINING SURFACES TO

RECEIVE NEW FINISHES AND/OR CONSTRUCTION

C. REMOVE AND DISPOSE OF COUNTERTOP AND ALL UPPER/BASE CABINETS. PREP REMAINING

SURFACES TO RECEIVE NEW FINISHES AND/OR CONSTRUCTION.

D. REMOVE METAL LOCKERS AND ALL RELATED ANCHORS, SUPPORTS, HARDWARE AND

ADHESIVES. RETURN TO OWNER.

TOILETS/PLUMBING

A. REMOVE AND DISPOSE OF PLUMBING FIXTURE - REFER TO PLUMBING DEMOLITION PLANS.

PREP REMAINING SURFACES TO RECEIVE NEW CONSTRUCTION AND/OR FINISHES.

B. REMOVE ACCESSORIES INCLUDING HAND DRYERS, PAPER TOWEL DISPENSERS, TOILET

PAPER DISPENSERS, SOAP DISPENSERS AND ALL RELATED ANCHORS, SUPPORTS,

HARDWARE AND ADHESIVES. RETURN TO OWNER.

MISCELLANEOUS

A. REMOVE AND DISPOSE OF MECHANICAL EQUIPMENT. REFER TO MECHANICAL DEMOLITION

PLANS.

B. REMOVE AND DISPOSE OF APPROXIMATELY 2,060 SQ. FT. OF EXISTING ROOF SYSTEM

DOWN TO CONCRETE ROOF DECK, ROOF DRAINS TO REMAIN.

C. REMOVE AND DISPOSE OF KITCHEN EQUIPMENT. REFER TO FOOD SERVICE DEMOLITION

PLANS.

CLASSROOM

3C

4C

4C

4C

5A

2D

2D

B

UL

K H

EA

D

2D

3D 3D

KINGSCOTT ASSOCIATES INC. KALAMAZOO, MICHIGANCC

JOB NO.

SHEET TITLE

SHEET NO.

ISSUANCES DATE

N

KEY PLAN

P L

E A

S E

R E

C Y

C L

E

T H

E S

E D

R A

W

IN

G S

A N

D T

H E

W O

R K

R E

P R

E S

E N

T E

D T

H E

R E

IN

A

R E

T H

E P

R O

P E

R T

Y O

F A

P

Y R

IG

H

T

K

IN

G

S C

O T

T A

S S

O C

IA

T

D

M A

Y N

O T

B E

U S

E D

O R

R E

P R

O D

U C

H

O U

T P

E R

M

IS

S

IO

N

L A

S T

P R

IN

T

E D ljh

KALAMAZOO | CHELSEA | GRAND RAPIDS | ROYAL OAK

/2

/2

:5 :1

P

M

C

U s e rs

\r s in g h \D o c u m e n ts

\L S

D H ill C e n te r S u m m e r

R e m o d e l_

A rc h r2 rs in g h P

P C

T

.r v t

2612.03

FIRST FLOOR DEMOLITION PLAN -

UNIT 200B

D1.2B

W ise

R d.

L an sin g, M I 4

La ns in g

S ch o o l D is tr ic t

H il l C e n te r S u m m e r

R e n o v a ti o n s

ADDENDUM 01 02/26/2025

1/8" = 1'-0"1

FIRST FLOOR DEMOLITION PLAN - UNIT 200BFIRST FLOOR DEMOLITION PLAN - UNIT 200B

1. CONTRACTOR IS RESPONSIBLE TO COORDINATE WITH ALL OTHER DRAWINGS AND

SPECIFICATIONS FOR ADDITIONAL AREAS THAT WILL REQUIRE DEMOLITION NOT INDICATED

ON THESE SHEETS.

2. THE DEMOLITION PLANS GENERALLY INDICATE AREAS OF EXTENSIVE REMOVALS AND DO

NOT INDICATE ALL OF THE WORK. CONTRACTOR SHALL PERFORM ALL DEMOLITION WHICH

IS NECESSARY FOR THE PROPER EXECUTION OF THE PROJECT WHETHER OR NOT SAID

DEMOLITION IS SPECIFICALLY INDICATED WITHIN THE DOCUMENTS.

3. CONTRACTOR IS RESPONSIBLE TO INFILL, PATCH AND/ OR REPAIR, EXISTING WALL, FLOORS

AND CEILINGS TO MATCH EXISTING WHERE DEMOLITION OCCURS OTHER THAN AS DESCRIBED

IN THESE DOCUMENTS.

4. IT IS THE INTENTION OF THESE DOCUMENTS THAT THE DEMOLITION OF PORTIONS OF

MASONRY WALLS (BOTH INTERIOR AND EXTERIOR) ARE GENERALLY TO BE DONE ALONG

JOINT AND COURSING LINES.

5. PATCH AND REPAIR REMAINING ADJACENT SURFACES AT AREAS OF REMOVAL AND/ OR

ALTERATION TO MATCH EXISTING. PROVIDE A SOUND AND PROPER SUBSTRATE FOR NEW

FINISH. COORDINATE WITH COLOR PLANS. WHERE A NEW FINISH IS NOT INDICATED, MATCH

EXISTING ADJACENT FINISHES.

6. ALL DEMOLITION IS TO BE DONE WITH REASONABLE CARE AS TO MINIMIZE DAMAGE TO

EXISTING REMAINING SURFACES. CONTRACTOR IS RESPONSIBLE TO PROPERLY DISPOSE OF

ALL DEMOLISHED ITEMS NOT INDICATED TO BE RELOCATED OR TURNED OVER TO OWNER.

7. REMOVE AND TURN OVER TO OWNER ALL FIRE EXTINGUISHERS AND CABINETS AT AREAS TO

BE DEMOLISHED, IF NOT OTHERWISE INDICATED TO BE RELOCATED.

8. CLEAN AND PREPARE ALL EXISTING SURFACES WHICH ARE TO BE PAINTED/ PATCHED.

PREPARATION TO INCLUDE MINOR PATCHING.

9. COORDINATE WITH MECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS FOR FURTHER

DEMOLITION NOTES.

DEMOLITION PLAN KEYNOTES

FLOORS

A. PREP EXISTING CONCRETE FLOOR FOR NEW FLOOR.

B. REMOVE AND DISPOSE OF ALL FLOORING AND BASE. PREP REMAINING SURFACES TO

RECEIVE NEW FINISH. VERIFY EXISTING FLOORING EXTENTS IN FIELD.

C. REMOVE AND DISPOSE OF WALK-OFF CARPET.

D. REMOVE AND DISPOSE OF CONCRETE CURB.

WALLS

A. REMOVE STORE FRONT WALL CONSTRUCTION, FRAMING, AND ALL ANCHORS AND

SUPPORTS. PREP REMAINING SURFACES TO RECEIVE NEW FINISHES AND/OR CONSTRUCTION.

B. REMOVE AND DISPOSE MASONRY WALL CONSTRUCTION AND ALL RELATED

BRACING/SUPPORTS. PREP REMAINING SURFACES TO RECEIVE NEW FINISHES AND/OR

CONSTRUCTION. REFER TO STRUCTURAL FOR LINTEL.

C. REMOVE WINDOW WITHIN WALL, FRAMING, AND ALL ANCHORS AND SUPPORTS. PREP

REMAINING SURFACES TO RECEIVE NEW FINISHES AND/OR CONSTRUCTION.

D. REMOVE GYPSUM BOARD WALL CONSTRUCTION, FRAMING, AND ALL ANCHORS AND

SUPPORTS. PREP REMAINING SURFACES TO RECEIVE NEW FINISHES AND/OR CONSTRUCTION

E. REMOVE AND DISPOSE OF MASONRY CURB. PREP SURFACES TO RECEIVE NEW FINISHES

AND/OR CONSTRUCTION.

DOORS

A. REMOVE AND DISPOSE OF EXTERIOR DOOR, INCLUDING FRAME, SIDELIGHTS, TRANSOMS

AND ALL RELATED ANCHORS AND SUPPORTS. SAWCUT ALL FRAME ANCHORS - PRYING

ANCHORS FROM SUBSTRATES IS UNACCEPTABLE. SALVAGE HARDWARE & RETURN TO

OWNER.

B. REMOVE AND DISPOSE OF INTERIOR DOOR, INCLUDING FRAME, SIDELIGHTS AND ALL

RELATED ANCHORS AND SUPPORTS. SAWCUT ALL FRAME ANCHORS - PRYING ANCHORS

FROM SUBSTRATES IS UNACCEPTABLE. SALVAGE HARDWARE & RETURN TO OWNER.

C. REMOVE AND DISPOSE OF PARTITION WALL AND DOOR. PREP REMAINING SURFACES TO

RECEIVE NEW FINISHES AND/OR CONSTRUCTION.

D. REMOVE DOOR KNOB, RETURN TO OWNER.

CASEWORK

A. REMOVE AND DISPOSE OF COUNTERTOP. PREP REMAINING SURFACES TO RECEIVE NEW

FINISHES AND/OR CONSTRUCTION.

B. REMOVE AND SALVAGE BENCH. RETURN TO OWNER. PREP REMAINING SURFACES TO

RECEIVE NEW FINISHES AND/OR CONSTRUCTION

C. REMOVE AND DISPOSE OF COUNTERTOP AND ALL UPPER/BASE CABINETS. PREP REMAINING

SURFACES TO RECEIVE NEW FINISHES AND/OR CONSTRUCTION.

D. REMOVE METAL LOCKERS AND ALL RELATED ANCHORS, SUPPORTS, HARDWARE AND

ADHESIVES. RETURN TO OWNER.

TOILETS/PLUMBING

A. REMOVE AND DISPOSE OF PLUMBING FIXTURE - REFER TO PLUMBING DEMOLITION PLANS.

PREP REMAINING SURFACES TO RECEIVE NEW CONSTRUCTION AND/OR FINISHES.

B. REMOVE ACCESSORIES INCLUDING HAND DRYERS, PAPER TOWEL DISPENSERS, TOILET

PAPER DISPENSERS, SOAP DISPENSERS AND ALL RELATED ANCHORS, SUPPORTS,

HARDWARE AND ADHESIVES. RETURN TO OWNER.

MISCELLANEOUS

A. REMOVE AND DISPOSE OF MECHANICAL EQUIPMENT. REFER TO MECHANICAL DEMOLITION

PLANS.

B. REMOVE AND DISPOSE OF APPROXIMATELY 2,060 SQ. FT. OF EXISTING ROOF SYSTEM

DOWN TO CONCRETE ROOF DECK, ROOF DRAINS TO REMAIN.

C. REMOVE AND DISPOSE OF KITCHEN EQUIPMENT. REFER TO FOOD SERVICE DEMOLITION

PLANS.

6KITCHEN

B104E

3B3B3B 3C 2C

1B

4C

1B

3B 4C

2D

1D

6C

3B

KINGSCOTT ASSOCIATES INC. KALAMAZOO, MICHIGANCC

JOB NO.

SHEET TITLE

SHEET NO.

ISSUANCES DATE

N

KEY PLAN

P L

E A

S E

R E

C Y

C L

E

T H

E S

E D

R A

W

IN

G S

A N

D T

H E

W O

R K

R E

P R

E S

E N

T E

D T

H E

R E

IN

A

R E

T H

E P

R O

P E

R T

Y O

F A

P

Y R

IG

H

T

K

IN

G

S C

O T

T A

S S

O C

IA

T

D

M A

Y N

O T

B E

U S

E D

O R

R E

P R

O D

U C

H

O U

T P

E R

M

IS

S

IO

N

L A

S T

P R

IN

T

E D ljh

KALAMAZOO | CHELSEA | GRAND RAPIDS | ROYAL OAK

/2

/2

:5 :1

P

M

C

U s e rs

\r s in g h \D o c u m e n ts

\L S

D H ill C e n te r S u m m e r

R e m o d e l_

A rc h r2 rs in g h P

P C

T

.r v t

2612.03

FIRST FLOOR DEMOLITION PLAN -

UNIT 300

D1.3

W ise

R d.

L an sin g, M I 4

La ns in g

S ch o o l D is tr ic t

H il l C e n te r S u m m e r

R e n o v a ti o n s

1/8" = 1'-0"1

FIRST FLOOR DEMOLITION PLAN - UNIT 300FIRST FLOOR DEMOLITION PLAN - UNIT 300

CLASSROOM

OFFICE

CEILING DEMO LEGEND

REMOVE AND DISPOSE OF ACOUSTICAL PANEL CEILING

AND GRID AS REQUIRED FOR NEW CONSTRUCTION.

COORDINATE ALL NECESSARY ELECTRICAL AND

MECHANICAL REMOVALS AND REPLACEMENT WITH

ELECTRICAL AND MECHANICAL CONTRACTORS.

REMOVE AND DISPOSE OF GYPSUM BOARD CEILING, FURRING,

ANCHORS, SUPPORTS AND ATTACHMENTS AS REQUIRED FOR NEW

CONSTRUCTION, MECHANICAL OR ELECTRICAL WORK. COORDINATE ALL

NECESSARY ELECTRICAL AND MECHANICAL REMOVAL AND

REPLACEMENT WITH ELECTRICAL AND MECHANICAL CONTRACTORS.

REFLECTED CEILING PLAN DEMO KEYNOTES

1 REMOVE AND DISPOSE OF PARTITION WALL TRACK AT CEILING. PREP REMAINING

SURFACES TO RECEIVE NEW FINISHES AND/OR CONSTRUCTION.

EXISTING CEILING TO REMAIN.

KINGSCOTT ASSOCIATES INC. KALAMAZOO, MICHIGANCC

JOB NO.

SHEET TITLE

SHEET NO.

ISSUANCES DATE

N

KEY PLAN

P L

E A

S E

R E

C Y

C L

E

T H

E S

E D

R A

W

IN

G S

A N

D T

H E

W O

R K

R E

P R

E S

E N

T E

D T

H E

R E

IN

A

R E

T H

E P

R O

P E

R T

Y O

F A

P

Y R

IG

H

T

K

IN

G

S C

O T

T A

S S

O C

IA

T

D

M A

Y N

O T

B E

U S

E D

O R

R E

P R

O D

U C

H

O U

T P

E R

M

IS

S

IO

N

L A

S T

P R

IN

T

E D ljh

KALAMAZOO | CHELSEA | GRAND RAPIDS | ROYAL OAK

/2

/2

:5 :2

P

M

C

U s e rs

\r s in g h \D o c u m e n ts

\L S

D H ill C e n te r S u m m e r

R e m o d e l_

A rc h r2 rs in g h P

P C

T

.r v t

2612.03

FIRST FLOOR REFLECTED CELING

DEMOLITION PLAN - UNIT 200B

D2.12B

W ise

R d.

L an sin g, M I 4

La ns in g

S ch o o l D is tr ic t

H il l C e n te r S u m m e r

R e n o v a ti o n s

ADDENDUM 01 02/26/2025

FIRST FLOOR REFLECTED CEILING DEMOLITION PLAN - UNIT 200BFIRST FLOOR REFLECTED CEILING DEMOLITION PLAN - UNIT 200B

ARCHITECTURAL PLAN KEYNOTES

1 PATCH EXISTING FLOOR DUE TO WALL REMOVAL. MATCH ADJACENT MATERIALS AND

FINISHES.

PATCH EXISTING WALL CONSTRUCTION DUE TO WALL REMOVAL OR OTHER ASSOCIATED

DEMOLITION. MATCH ADJACENT MATERIALS AND FINISHES.

NEW 6-LITER CLASS K WET CHEMICAL FIRE EXTINGUISHER, BRACKET MOUNTED AT 48"

AFF.

NEW DOOR LEVER ON EXISTING CLASSROOM DOOR.

PRODUCT: CORBIN RUSSWIN ML2002.

TRIM DESIGN: CORBIN RUSSWIN LUSTRA LWA

INSIDE INDICATOR: CORBIN RUSSWIN ML190 V01

FINISH: 626

CYLINDER: LESS CYL BOTH SIDES

NEW DOOR LEVER ON EXISTING TOILET ROOM DOOR.

PRODUCT: CORBIN RUSSWIN ML2060.

TRIM DESIGN: CORBIN RUSSWIN LUSTRA LWA

OUTSIDE INDICATIOR: CORBIN RUSSWIN ML190 V21

FINISH: 626

NEW DOOR LEVER ON EXISTING STOREROOM DOOR.

PRODUCT: CORBIN RUSSWIN ML2057.

TRIM DESIGN: CORBIN RUSSWIN LUSTRA LWA

FINISH: 626

NEW DOOR LEVER ON EXISTING OFFICE/CLASSROOM DOOR.

PRODUCT: CORBIN RUSSWIN ML2055.

TRIM DESIGN: CORBIN RUSSWIN LUSTRA LWA

FINISH: 626

NEW GRAB BARS IN EXISTING TOILET ROOM.

GRAB BAR - BOBRICK #6806x42

GRAB BAR - BOBRICK #6806x36 (AMBULATORY)

GRAB BAR - BOBRICK #B-6806.99 - 18" VERTICAL

NEW 3-5/8" MTL STUD WALL UP TO EXISTING CEILING WITH 5/8" GYP EACH SIDE. REFER

TO DETAIL 2/A2.30.

NEW 3-5/8" MTL STUD CHASE WALL WITH 5/8" GYP ON ONE SIDE. FINISH WITH FRP

PANEL. REFER TO DETAIL 3/A2.30.

PATCH EXISTING OPENING WITH METAL STUD AND GYP. FINISH WITH FRP PANEL. WALL TO

ALIGN WITH ADJACENT SURFACE.

PATCH OPENING TO MATCH ADJACENT BRICK MASONRY.

NEW 3-5/8" MTL STUD WALL UP TO DECK WITH 5/8" GYP EACH SIDE. REFER TO DETAIL

1/A2.30.

PATCH OPENING TO MATCH ADJACENT METAL STUD WALL WITH GYP ON EACH SIDE.

1. INDICATES CONSTRUCTION DOCUMENT ROOM NUMBERS.

2. REFER TO EQUIPMENT PLANS FOR CASEWORK, VISUAL DISPLAY BOARDS, LOCKERS,

SHELVING, ETC.

3. REFER TO COLOR LAYOUT PLANS FOR FLOOR FINISH PATTERNS AND COLORS.

4. MASONRY CONTRACTOR TO INSTALL LOOSE LINTELS FOR MISCELLANEOUS OPENINGS NOT

INDICATED ON DRAWINGS BUT REQUIRED FOR MECHANICAL, ELECTRICAL, FOOD SERVICE

EQUIPMENT OR OTHER ITEMS THAT PASS THROUGH A WALL. STEEL LINTELS SHALL BE

SUPPLIED BY THE STEEL CONTRACTOR.

5. DIMENSIONS SHOWN ARE TO FACE OF WALL.

XX

ARCHITECTURAL GENERAL NOTES

TOILET

C103

NURSE

VEST

7' -4

PRINCIPAL

WELCOME

201 10

15'-0"

A9.1

A9.1

A3.1

A3.1 32

CORRIDOR

100K

LOW ROOF ABOVE

A3.1

17'-8"

A9.1

A9.1

A9.1

A3.3 _______________________1

A3.3

200A

B

D

C

B

A

D

C

B

A

A

BL-1 BL1

SS-1 SS-1

S S -2

B S S -2

A S S -2

A S S -3

S S -7

S S -4

42A

42B45B

45A

7 1/2"

7 1/2"

7 1/2"

7 1/2"

7 1/2"

100D

8'-6"

SS-5

S S -6

KINGSCOTT ASSOCIATES INC. KALAMAZOO, MICHIGANCC

JOB NO.

SHEET TITLE

SHEET NO.

ISSUANCES DATE

N

KEY PLAN

P L

E A

S E

R E

C Y

C L

E

T H

E S

E D

R A

W

IN

G S

A N

D T

H E

W O

R K

R E

P R

E S

E N

T E

D T

H E

R E

IN

A

R E

T H

E P

R O

P E

R T

Y O

F A

P

Y R

IG

H

T

K

IN

G

S C

O T

T A

S S

O C

IA

T

D

M A

Y N

O T

B E

U S

E D

O R

R E

P R

O D

U C

H

O U

T P

E R

M

IS

S

IO

N

L A

S T

P R

IN

T

E D ljh

KALAMAZOO | CHELSEA | GRAND RAPIDS | ROYAL OAK

/2

/2

:5 :2

P

M

C

U s e rs

\r s in g h \D o c u m e n ts

\L S

D H ill C e n te r S u m m e r

R e m o d e l_

A rc h r2 rs in g h P

P C

T

.r v t

2612.03

FIRST FLOOR PLAN - UNIT 200

A1.2

W ise

R d.

L an sin g, M I 4

La ns in g

S ch o o l D is tr ic t

H il l C e n te r S u m m e r

R e n o v a ti o n s

1/8" = 1'-0"1

FIRST FLOOR PLAN - UNIT 200FIRST FLOOR PLAN - UNIT 200

A3.1

CLASSROOM

OFFICE

4 4

A

LI

G N

ARCHITECTURAL PLAN KEYNOTES

1 PATCH EXISTING FLOOR DUE TO WALL REMOVAL. MATCH ADJACENT MATERIALS AND

FINISHES.

PATCH EXISTING WALL CONSTRUCTION DUE TO WALL REMOVAL OR OTHER ASSOCIATED

DEMOLITION. MATCH ADJACENT MATERIALS AND FINISHES.

NEW 6-LITER CLASS K WET CHEMICAL FIRE EXTINGUISHER, BRACKET MOUNTED AT 48"

AFF.

NEW DOOR LEVER ON EXISTING CLASSROOM DOOR.

PRODUCT: CORBIN RUSSWIN ML2002.

TRIM DESIGN: CORBIN RUSSWIN LUSTRA LWA

INSIDE INDICATOR: CORBIN RUSSWIN ML190 V01

FINISH: 626

CYLINDER: LESS CYL BOTH SIDES

NEW DOOR LEVER ON EXISTING TOILET ROOM DOOR.

PRODUCT: CORBIN RUSSWIN ML2060.

TRIM DESIGN: CORBIN RUSSWIN LUSTRA LWA

OUTSIDE INDICATIOR: CORBIN RUSSWIN ML190 V21

FINISH: 626

NEW DOOR LEVER ON EXISTING STOREROOM DOOR.

PRODUCT: CORBIN RUSSWIN ML2057.

TRIM DESIGN: CORBIN RUSSWIN LUSTRA LWA

FINISH: 626

NEW DOOR LEVER ON EXISTING OFFICE/CLASSROOM DOOR.

PRODUCT: CORBIN RUSSWIN ML2055.

TRIM DESIGN: CORBIN RUSSWIN LUSTRA LWA

FINISH: 626

NEW GRAB BARS IN EXISTING TOILET ROOM.

GRAB BAR - BOBRICK #6806x42

GRAB BAR - BOBRICK #6806x36 (AMBULATORY)

GRAB BAR - BOBRICK #B-6806.99 - 18" VERTICAL

NEW 3-5/8" MTL STUD WALL UP TO EXISTING CEILING WITH 5/8" GYP EACH SIDE. REFER

TO DETAIL 2/A2.30.

NEW 3-5/8" MTL STUD CHASE WALL WITH 5/8" GYP ON ONE SIDE. FINISH WITH FRP

PANEL. REFER TO DETAIL 3/A2.30.

PATCH EXISTING OPENING WITH METAL STUD AND GYP. FINISH WITH FRP PANEL. WALL TO

ALIGN WITH ADJACENT SURFACE.

PATCH OPENING TO MATCH ADJACENT BRICK MASONRY.

NEW 3-5/8" MTL STUD WALL UP TO DECK WITH 5/8" GYP EACH SIDE. REFER TO DETAIL

1/A2.30.

PATCH OPENING TO MATCH ADJACENT METAL STUD WALL WITH GYP ON EACH SIDE.

1. INDICATES CONSTRUCTION DOCUMENT ROOM NUMBERS.

2. REFER TO EQUIPMENT PLANS FOR CASEWORK, VISUAL DISPLAY BOARDS, LOCKERS,

SHELVING, ETC.

3. REFER TO COLOR LAYOUT PLANS FOR FLOOR FINISH PATTERNS AND COLORS.

4. MASONRY CONTRACTOR TO INSTALL LOOSE LINTELS FOR MISCELLANEOUS OPENINGS NOT

INDICATED ON DRAWINGS BUT REQUIRED FOR MECHANICAL, ELECTRICAL, FOOD SERVICE

EQUIPMENT OR OTHER ITEMS THAT PASS THROUGH A WALL. STEEL LINTELS SHALL BE

SUPPLIED BY THE STEEL CONTRACTOR.

5. DIMENSIONS SHOWN ARE TO FACE OF WALL.

XX

ARCHITECTURAL GENERAL NOTES

KINGSCOTT ASSOCIATES INC. KALAMAZOO, MICHIGANCC

JOB NO.

SHEET TITLE

SHEET NO.

ISSUANCES DATE

N

KEY PLAN

P L

E A

S E

R E

C Y

C L

E

T H

E S

E D

R A

W

IN

G S

A N

D T

H E

W O

R K

R E

P R

E S

E N

T E

D T

H E

R E

IN

A

R E

T H

E P

R O

P E

R T

Y O

F A

P

Y R

IG

H

T

K

IN

G

S C

O T

T A

S S

O C

IA

T

D

M A

Y N

O T

B E

U S

E D

O R

R E

P R

O D

U C

H

O U

T P

E R

M

IS

S

IO

N

L A

S T

P R

IN

T

E D ljh

KALAMAZOO | CHELSEA | GRAND RAPIDS | ROYAL OAK

/2

/2

:5 :2

P

M

C

U s e rs

\r s in g h \D o c u m e n ts

\L S

D H ill C e n te r S u m m e r

R e m o d e l_

A rc h r2 rs in g h P

P C

T

.r v t

2612.03

FIRST FLOOR PLAN - UNIT 200B

A1.2B

W ise

R d.

L an sin g, M I 4

La ns in g

S ch o o l D is tr ic t

H il l C e n te r S u m m e r

R e n o v a ti o n s

ADDENDUM 01 02/26/2025

FIRST FLOOR PLAN - UNIT 200BFIRST FLOOR PLAN - UNIT 200B

ARCHITECTURAL PLAN KEYNOTES

1 PATCH EXISTING FLOOR DUE TO WALL REMOVAL. MATCH ADJACENT MATERIALS AND

FINISHES.

PATCH EXISTING WALL CONSTRUCTION DUE TO WALL REMOVAL OR OTHER ASSOCIATED

DEMOLITION. MATCH ADJACENT MATERIALS AND FINISHES.

NEW 6-LITER CLASS K WET CHEMICAL FIRE EXTINGUISHER, BRACKET MOUNTED AT 48"

AFF.

NEW DOOR LEVER ON EXISTING CLASSROOM DOOR.

PRODUCT: CORBIN RUSSWIN ML2002.

TRIM DESIGN: CORBIN RUSSWIN LUSTRA LWA

INSIDE INDICATOR: CORBIN RUSSWIN ML190 V01

FINISH: 626

CYLINDER: LESS CYL BOTH SIDES

NEW DOOR LEVER ON EXISTING TOILET ROOM DOOR.

PRODUCT: CORBIN RUSSWIN ML2060.

TRIM DESIGN: CORBIN RUSSWIN LUSTRA LWA

OUTSIDE INDICATIOR: CORBIN RUSSWIN ML190 V21

FINISH: 626

NEW DOOR LEVER ON EXISTING STOREROOM DOOR.

PRODUCT: CORBIN RUSSWIN ML2057.

TRIM DESIGN: CORBIN RUSSWIN LUSTRA LWA

FINISH: 626

NEW DOOR LEVER ON EXISTING OFFICE/CLASSROOM DOOR.

PRODUCT: CORBIN RUSSWIN ML2055.

TRIM DESIGN: CORBIN RUSSWIN LUSTRA LWA

FINISH: 626

NEW GRAB BARS IN EXISTING TOILET ROOM.

GRAB BAR - BOBRICK #6806x42

GRAB BAR - BOBRICK #6806x36 (AMBULATORY)

GRAB BAR - BOBRICK #B-6806.99 - 18" VERTICAL

NEW 3-5/8" MTL STUD WALL UP TO EXISTING CEILING WITH 5/8" GYP EACH SIDE. REFER

TO DETAIL 2/A2.30.

NEW 3-5/8" MTL STUD CHASE WALL WITH 5/8" GYP ON ONE SIDE. FINISH WITH FRP

PANEL. REFER TO DETAIL 3/A2.30.

PATCH EXISTING OPENING WITH METAL STUD AND GYP. FINISH WITH FRP PANEL. WALL TO

ALIGN WITH ADJACENT SURFACE.

PATCH OPENING TO MATCH ADJACENT BRICK MASONRY.

NEW 3-5/8" MTL STUD WALL UP TO DECK WITH 5/8" GYP EACH SIDE. REFER TO DETAIL

1/A2.30.

PATCH OPENING TO MATCH ADJACENT METAL STUD WALL WITH GYP ON EACH SIDE.

1. INDICATES CONSTRUCTION DOCUMENT ROOM NUMBERS.

2. REFER TO EQUIPMENT PLANS FOR CASEWORK, VISUAL DISPLAY BOARDS, LOCKERS,

SHELVING, ETC.

3. REFER TO COLOR LAYOUT PLANS FOR FLOOR FINISH PATTERNS AND COLORS.

4. MASONRY CONTRACTOR TO INSTALL LOOSE LINTELS FOR MISCELLANEOUS OPENINGS NOT

INDICATED ON DRAWINGS BUT REQUIRED FOR MECHANICAL, ELECTRICAL, FOOD SERVICE

EQUIPMENT OR OTHER ITEMS THAT PASS THROUGH A WALL. STEEL LINTELS SHALL BE

SUPPLIED BY THE STEEL CONTRACTOR.

5. DIMENSIONS SHOWN ARE TO FACE OF WALL.

XX

ARCHITECTURAL GENERAL NOTES

KITCHEN

B104E

CORRIDOR

100K

A

BL-1 BL1

/4

100D

KINGSCOTT ASSOCIATES INC. KALAMAZOO, MICHIGANCC

JOB NO.

SHEET TITLE

SHEET NO.

ISSUANCES DATE

N

KEY PLAN

P L

E A

S E

R E

C Y

C L

E

T H

E S

E D

R A

W

IN

G S

A N

D T

H E

W O

R K

R E

P R

E S

E N

T E

D T

H E

R E

IN

A

R E

T H

E P

R O

P E

R T

Y O

F A

P

Y R

IG

H

T

K

IN

G

S C

O T

T A

S S

O C

IA

T

D

M A

Y N

O T

B E

U S

E D

O R

R E

P R

O D

U C

H

O U

T P

E R

M

IS

S

IO

N

L A

S T

P R

IN

T

E D ljh

KALAMAZOO | CHELSEA | GRAND RAPIDS | ROYAL OAK

/2

/2

:5 :3

P

M

C

U s e rs

\r s in g h \D o c u m e n ts

\L S

D H ill C e n te r S u m m e r

R e m o d e l_

A rc h r2 rs in g h P

P C

T

.r v t

2612.03

FIRST FLOOR PLAN - UNIT 300

A1.3

W ise

R d.

L an sin g, M I 4

La ns in g

S ch o o l D is tr ic t

H il l C e n te r S u m m e r

R e n o v a ti o n s

1/8" = 1'-0"1

FIRST FLOOR PLAN - UNIT 300FIRST FLOOR PLAN - UNIT 300

CLASSROOM

OFFICE

9'-2

9'-2

ACT-1

ACT-1 3

REFLECTED CEILING PLAN GENERAL NOTES

1. REFER TO CODE COMPLIANCE PLANS FOR VERTICAL FIRE RESISTANT RATINGS AT WALLS AND

HORIZONTAL FIRE RESISTANT RATINGS AT CEILINGS.

2. PROVIDE RATED SEALANT AND/ OR STOPPING AT ALL PENETRATIONS AND OPENING THROUGH

ALL EXISTING AND NEW CORRIDOR WALLS AND FIRE RATED PARTITIONS.

3. PROVIDE ACOUSTICAL SEALANT AND/ OR STOPPING AT ALL PENETRATIONS THROUGH NON-

FIRE RATED WALLS.

4. REFER TO COLOR LAYOUT PLANS FOR COLOR INFORMATION.

5. FACTORY FINISH ALL EXPOSED GRID ON ALL SURFACE.

6. IF CONTROL JOINTS ARE NOT INDICATED IN GYPSUM BOARD CEILINGS, PROVIDE AS

RECOMMENDED.

7. ACOUSTICAL PANEL CEILINGS SHALL BE APC-1, U.N.O.

REFLECTED CEILING PLAN KEYNOTES

1 EXISTING CEILING TO REMAIN.

PATCH EXISTING CEILING WHERE LIGHT FIXTURES WERE REMOVED.

PROVIDE NEW CELING TILES AND GRID.

PROVIDE NEW GYP BOARD CEILING.

PROVIDE NEW ACOUSTICAL CEILING BAFFLES.

NEW CEILING BULKHEAD. REFER TO DETAIL 4/A2.30.

REFLECTED CEILING LEGEND

C M

2'x4' SURFACE MOUNTED LIGHT FIXTURE

1'x4' SURFACE MOUTNED LIGHT FIXTURE

2'x4' RECESSED LIGHT FIXTURE

1'x4' RECESSED LIGHT FIXTURE

CEILING MOUNTED EXIT SIGN

SPRINKLER HEAD

SUPPLY DIFFUSER

SUPPLY DIFFUSER

RETURN / EXHAUST GRILLE

KINGSCOTT ASSOCIATES INC. KALAMAZOO, MICHIGANCC

JOB NO.

SHEET TITLE

SHEET NO.

ISSUANCES DATE

N

KEY PLAN

P L

E A

S E

R E

C Y

C L

E

T H

E S

E D

R A

W

IN

G S

A N

D T

H E

W O

R K

R E

P R

E S

E N

T E

D T

H E

R E

IN

A

R E

T H

E P

R O

P E

R T

Y O

F A

P

Y R

IG

H

T

K

IN

G

S C

O T

T A

S S

O C

IA

T

D

M A

Y N

O T

B E

U S

E D

O R

R E

P R

O D

U C

H

O U

T P

E R

M

IS

S

IO

N

L A

S T

P R

IN

T

E D ljh

KALAMAZOO | CHELSEA | GRAND RAPIDS | ROYAL OAK

/2

/2

:5 :3

P

M

C

U s e rs

\r s in g h \D o c u m e n ts

\L S

D H ill C e n te r S u m m e r

R e m o d e l_

A rc h r2 rs in g h P

P C

T

.r v t

2612.03

FIRST FLOOR REFLECTED CEILING

PLAN - UNIT 200B

A2.2B

W ise

R d.

L an sin g, M I 4

La ns in g

S ch o o l D is tr ic t

H il l C e n te r S u m m e r

R e n o v a ti o n s

ADDENDUM 01 02/26/2025

FIRST FLOOR REFLECTED CEILING PLAN - UNIT 200BFIRST FLOOR REFLECTED CEILING PLAN - UNIT 200B

DOOR TYPES

FIELD VERIFY OPENING SIZE PRIOR TO MANUFACTURING

F

TYP.

SEE SCHEDULE 4" 5"

2' -0

4'

-2

TY

P

SE

E

SC

HE

D

UL

E

NL FG2

5"5"

5" 1'-

4" 1'-

6" 5"