S02 - ATTACHMENT 1 -Final SOW - Phoenix Pkg. 25 - Conveyor Belt.docx

FY22Q1-025 | JSN: K1580A | Conveyor Belt

Phoenix VA Health Care System Initial Outfitting, Transition & Activation Statement of Work Conveyor Belt System (JSN: K1580A) 12/14/21 V3

Phoenix VA Health Care System Phoenix VA Clinic – 32nd Street Project 400 North 32nd St.

Phoenix, AZ 85008 Introduction The Phoenix Veteran Affairs Health Care System has a requirement to purchase a Conveyor Belt System (JSN: K1580A) via an authorized vendor to supply and deliver the item(s) identified in Table 1 below. See salient characteristics below. This is a Brand Name or Equal Requirement. This requirement is in support of the activation of Phoenix VA Clinic – 32nd Street Project. The new Outpatient Clinic has the need for One (1) Conveyor Belt System to be used in the new Pharmacy Department. Smart Move Modular Conveyors Part Number 7567-1 and Part Number 7567-2 are the basis’s of design.

Table 1 – Package Items Summary

CLIN

(1 ON EACH SIDE OF BELT)

(3 CUT OUTS ON EACH SIDE OF BELT)

(1 ON EACH SIDE OF BELT)

(12” W x 216” L)

Additional Item Requirements The vendor will provide service manuals that includes theory of operation, maintenance requirements, repair information, schematics, part lists and troubleshooting information in electronic format for use by the VA IT Operations Department.

Date of manufacture must not be greater than 2 years before the purchase order date. The equipment must not be used or refurbished and must have the latest manufacturer’s software/hardware updates installed. Any batteries provided with the unit will not be manufactured more than 12 months before the purchase order issue date.

General Conditions Site Address The address of the Phoenix VA Clinic – 32nd Street is provided below.

400 North 32nd St.

Phoenix, AZ 85008

Delivery Schedule Items shall be delivered no earlier than the estimated delivery start date and no later than the delivery end date listed in Table 2 below.

Table 2 – Anticipated Building Outfitting Schedule

Schedule and Order Management

Delivery and Receiving

2.4.1 Delivery and receipt of the proposed items is anticipated to be directed to the location identified below. Confirmation of delivery location will be provided post-award. To coordinate delivery, contact VA POC David Charnetsky at (602) 277-5551 ext. 5228, david.charnetsky@va.gov; SME-Solutions POC, Soren Nicholson at (719) 761-4387, Soren.Nicholson@sme-solutions.co; Robert Stonerook at (706) 304-7194, Robert.stonerook@sme-solutions.co; and Jerrell (Jeff) Cockrell at (636) 395-9761, Jerrell.cockrell@sme-solutions.co.

☒ Phoenix VA Clinic – 32nd Street (Direct Delivery to address detailed in paragraph 2.1) ☐ IOT&A Contractor provided warehouse: Address TBD

2.4.6 NOTE: Due to the COVID19 situation, the vendor must follow CDC guidelines when on VA property. Any individuals who need to enter the building for installation &/or training will be required to be screened by the site staff prior to entry. Please allow time for this in your schedule.

Clean Up and Disposal There are no dumpsters available for vendor use.

The removal of waste and/or excess material shall be conducted through the loading dock area.

Assembly, Installation, and Calibration Required (Yes ☒ No ☐) The vendor is required to manage and coordinate installation at the Phoenix VA Clinic – 32nd Street with the COR or his representative IOT&A POC.

On-site assembly and installation of items, and performance of services identified in this document shall take place during normal business hours which are defined as: 8:00 AM to 4:30 PM Mountain Standard Time, Monday through Friday, and excluding Federal Holidays.

Proposed installation date will occur after delivery of equipment. Current timeframe of delivery is February 28, 2022 – March 28, 2022.

The vendor is required to define the need for a staging area to accommodate item assembly and installation, if needed. Post-award, this information will be confirmed with the vendor.

The vendor is required to provide tools, labor and materials to complete assembly and installation of the items detailed in this document.

The vendor shall protect all finished spaces and surfaces as required from delivery and installation damage. The vendor shall use covering and protection to the extent necessary to prevent damage to finished spaces. Any damage occurred during delivery and installation is the responsibility of the vendor. The vendor will be responsible for paying for and repairing any damage or noted deficiencies to finished spaces and surfaces that occur because of the vendor’s (or associated sub-contractors) installation.

During the entire duration of assembly and installation, the vendor will have a competent representative on-site as the vendor’s contact, and to serve as the interface between the vendor and the Phoenix VA Clinic – 32nd Street. On-site representative can be the installer. All instructions provided from COR to the representative will be binding as if given to the vendor’s main contact. The COR may provide specific instructions, however, only the Contracting Officer may change the terms or conditions of the contract.

Training Required (Yes ☒ No ☐) The vendor is required to provide live clinical training on set up, operation, shut down, and troubleshooting procedures to nursing staff.

The vendor shall coordinate training dates with the on-site Project Manager. Post-award, these dates will be confirmed with the vendor to meet the clinical schedule. Proposed training date will occur after installation of equipment.

Current timeframe of training is March-April 2022.

The vendor shall provide documentation and/or certification to each staff member that has successfully completed the training.

Confidentiality and Non-Disclosure This equipment does not connect to a VA network. Therefore, in accordance with Appendix A, Handbook 6500.6 Checklist, block 6, the C&A requirements do not apply to this requirement, and a Security Accreditation Package is not required.

This equipment does not hold or store patient information. Therefore, in accordance with Appendix A, Handbook 6500.6 Checklist block 7, Appendix B and C provisions do not apply.

Appendix B: The contractor, their personnel, and their subcontractors shall be subject to the Federal laws, regulations, standards, and VA Directives and Handbooks regarding information and information system security as delineated in this contract.

Appendix C: VA will own this equipment. If vendor needs access during delivery, assembly, install or repair, the contractor shall be escorted by a VA employee to ensure there is no exposure to VA sensitive information. If the contractor is required to be on site for more than two consecutive days, VHA Privacy Training, TMS Course VA10203, is required and available at https://www.tms.va.gov/SecureAuth35/. The contractor will provide all consumable supplies necessary for training and competency assessment of hospital staff. Proof of training will be provided to the COR upon request.

Salient characteristics Conveyor Belt (JSN: K1580A)

Total Quantity: 1 ☐ Network Required if Checked ☒ Manufacturer Certified Installation Required if Checked ☐ BMET Training Required if Checked ☒ End User Training Required if Checked

Basis of Design is SmartMove Modular Conveyors, MFG P/N: 7567-1; 7567-2 Brand Name or Equal Salient Characteristics:

· 12-inch Wide x 18-foot Long, High Temperature Belt Conveyor System

· Be heat resistant for materials over 80 degrees.

· One-directional (east to west)

· Belt can be solid or open.

· Includes a minimum of 1-inch-high guard rails throughout the length of the belt on both sides

· System must have a chain strength of at least 1000 lbs per foot

· Adjustable 1-25 Feet Per Minute (FPM) belt speed

· Emergency Stop button at each end of belt (minimum of two Emergency Stop buttons)

· The conveyor system will remain level and must be able to change heights between 34-45 inches

· Electrical: 120 V AC

· Wire Duct Kit shall be open or closed slot or comparable

· Solid work surface on both sides of the belt that goes the length of the belt system

· Work surface need not be attached to the conveyor.

· Each worksurface (one on each side of the belt) must be 24 inches Wide and 216” inches long (or 18 ft long).

· Each side must include a minimum of three (3) 12-inch Wide x 24-inch Long cut-outs for staff to be able to work and not have to extend their reach over the 24” inch worksurface. 3 cut outs evenly spaced along each side of the 18ft conveyor.

· Includes an auxiliary table that sits on the west end of the conveyor system

· Table dimension must meet 24 inches Wide x 96 inches Long

· Stainless steel configuration (16 gauge or greater)

· Table can be attached to the conveyor system or be standalone on stainless steel lockable casters

Statement of Work Page 1 of 8 image2.jpg