RFQ.pdf

1 V12 APR 2026

National Aeronautics and Space Administration

NASA Shared Services Center Stennis Space Center, MS 39529-6000

9/1/2026

SUBJECT: Request for Quotation (RFQ) 80NSSC26941668Q, COBRA2-100 PCB

This solicitation includes the following sections:

1. Statement of Work/Bid Schedule – Section 1

2. Instructions to Offerors – Section 2

3. Solicitation Provisions/Representations and Certifications – Section 3

4. Clauses/Terms and Conditions – Section 4

5. Quote Evaluation Criteria – Section 5

2 V12 APR 2026

SECTION 1

STATEMENT OF WORK/BID SCHEDULE

ENTER SOW/BID SCHEDULE:

STATEMENT OF WORK

1. Objective/Requirements Manufacture printed circuit boards (PCBs) for use in the Simulation Engineering Branch for hardware upgrades of next generation of simulation computers.

Assemble PCBs per IPC-A-610 Class 3 assembly standards.

2. Characteristics, Scope, and Specs

The contractor shall perform the following duties:

Dimensions: 10.1 x 5.5 inches.

Layers: 8 Finished copper weight: 1 ounce.

Fabricate or acquire PCBs from a domestic manufacturer built in accordance with IPC-6012, Class 3 standards. Per 6011, use supplied data files listed. PCBs shall meet the requirements of IPC-6012 Table 4-3 “Acceptance Testing and Frequency” for Class 3.

Materials used shall be laminate per IPC-2221 par 4.3; L40XXXXHX/HXAA IAW IPC-4101/24, laminated sheet, flame resistant, UL 94V-0.

PCB core and prepreg materials used must have a Tg of 140°C or greater.

All holes without dimensions are located on a modular grid of 0.0005-inch increments. All holes shall be located within 0.005-inch radius of true position in respect to datum A, datum B, datum C.

Hole locations are defined by the NC DRIL data file supplied.

Layer-to-layer registration shall be within 0.007 inches diameter of true position in respect to datum A, datum B, datum C.

Finished hole size is as indicated in hole drill table.

Soldermask for the prototypes (first 5 units and any possible follow-on prototypes) that are delivered shall be white and their silkscreen shall be black.

Finish:

o Production units, quantity 50: Apply liquid photo imageable solder mask per IPC-SM-480, Class H, color yellow, RGB: 255, 255, 0 or equivalent, to both sides of the PCB over bare copper. Via holes covered with solder mask must be plugged. Mask must be below flush to primary side surface. Maximum misregistration is +/-0.003 inches.

o Silkscreen shall be black, permanent, organic, non-conductive ink. There shall be no silkscreen on any solderable component pads.

o Prototypes units only, at least two batches, quantity 5 per batch: Solder mask for the prototypes (first 10 units and any possible follow-on lots) that are delivered shall be white and their silkscreen shall be black.

Process Allowances:

3 V12 APR 2026

o Warp or twist of PCBs shall not exceed 1%.

o Conductor widths and spacing shall be within +/-0.0015 inches of supplied Gerber data.

o Remove all burrs and break sharp edges, 0.015 inches maximum.

o 0.059 inch maximum radius on any inside corners.

Marking: UL Logo: Manufacturer’s identification/traceability and date code letter shall be rendered in etch on the bottom side of the board in accordance with IPC-6011.

Test requirements:

o 250VDC HIPOT (high potential) test required prior to board assembly.

o Flying probe test required before board assembly.

o Quality conformal test coupons shall be maintained for all inspection lots. Test coupons shall be in accordance with IPC-2221.

o A certificate of compliance shall be submitted with each lot.

With the exception of this statement of work, the information and files contained in this solicitation are technical in content, but not technical data as defined by the International Traffic in Arms Regulations (ITAR). With the exception of this statement of work, the information and files contained in this solicitation have been determined to be technology as defined by the Export Administration Regulations (EAR), not found under an ECCN of any category of the Commerce Control List, and therefore is designated as EAR99. Information designated as EAR99 shall be handled in accordance with the EAR. Violations of these regulations are punishable by fine, imprisonment, or both.

Supplied fabrication files (All EAR99/CUI):

o PCB-100_revProt-.apr o PCB-100_revProt-.DRR o PCB-100_revProt-.EXTREP o PCB-100_revProt-.G1 o PCB-100_revProt-.G2 o PCB-100_revProt-.G3 o PCB-100_revProt-.G4 o PCB-100_revProt-.G5 o PCB-100_revProt-.GBL o PCB-100_revProt-.GBO o PCB-100_revProt-.GBP o PCB-100_revProt-.GBS o PCB-100_revProt-.GKO o PCB-100_revProt-.GM o PCB-100_revProt-.GP1 o PCB-100_revProt-.GTL o PCB-100_revProt-.GTO o PCB-100_revProt-.GTP o PCB-100_revProt-.GTS o PCB-100_revProt-.LDP o PCB-100_revProt-.REP o PCB-100_revProt-.TXT o PCB-100_revProt--macro.APR_LIB

Supplied assembly files (All EAR99/CUI):

o PCB-100_RevProt-_BOM.xlsx o PCB-100_revProt-_Pick-Place.txt o PCB-100_revProt-_PCB_Assembly.pdf

4 V12 APR 2026

PCB thickness shall be less than or equal to 0.062 inches.

Acquire parts in provided bill of materials. Layer stack legend provided for reference.

Assemble PCB in accordance with IPC-A-610 Class 3 assembly standards.

5 V12 APR 2026

3. Deliverables and Schedule

Description Quantity Unit Delivery Date Prototype PCB 5 Each 3 weeks from contract award Cert. of Conform. 1 Each Delivered with prototypes Test reports 1 Each Delivered with prototypes Prototype PCB vs2 5 Each 3 weeks from receipt of revised design from NASA Cert. of Conform.

for PCB vs2

1 Each Delivered with prototypes

Test reports for PCB vs2

1 Each Delivered with prototypes

Prototype PCB vs3 (if needed)

5 Each 3 weeks from receipt of revised design from NASA

Cert. of Conform.

for PCB vs3

1 Each Delivered with prototypes

Test reports for PCB vs3

1 Each Delivered with prototypes

Production PCB 50 Each 5 weeks from confirmation of final design from NASA

Cert. of Conform. 1 Each Delivered with production units

Test reports 1 Each Delivered with production units

4. Place of Performance U.S. domestic facility as determined by the contractor.

5. Period of Performance Items must be delivered by dates specified in the table in section 3.

**Fabrication/Assembly files are only available by request. Requestor must be able to receive encrypted e-mails and be capable of recieving/viewing CUI data.**

6 V12 APR 2026

SECTION 2

INSTRUCTION TO OFFERORS

☒52.212-1 Instructions to Offerors – Commercial Products and Commerical Services. (APR

2026)(DEVIATION)

Addendum to 52.212-1

Quotes for the item(s) described in the RFQ are due by 9/7/2026 by 4:00 p.m. CT to Tracy Bremer at tracy.g.bremer@nasa.gov in order to be considered for award. If it is in the best interest of the Government, quotes submitted after the due date may be accepted. Quotes shall remain valid for 30 days unless otherwise expressly stated on the quote. Submitted Quotes shall list two points of contacts including name, phone number, and email address.

All contractual and technical questions must be in writing (e-mail) to Tracy Bremer at tracy.g.bremer@nasa.gov no later than 9/3/2026 by 12:00 p.m. CT. Telephone questions shall not be accepted.

The NAICS Code for this procurement is 333998.

This procurement is set aside for small business.

Offeror’s shall be registered at www.sam.gov in order to be considered for award.

Please provide the Cage Code/UEI (Unique Entity ID) # on your Quote

Please provide your ARO Delivery Time on your Quote

Delivery is FOB Destination (Please provide FOB Destination on your Quote)

Payment Terms are NET 30

7 V12 APR 2026

SECTION 3

SOLICITATION PROVISION/REPRESENTATIONS AND CERTIFICATIONS

☒52.252-1 SOLICITATION PROVISIONS INCORPORATED BY REFERENCE (FEB 1998)

This solicitation incorporates one or more solicitation provisions by reference, with the same force and effect as if they were given in full text. Upon request, the Contracting Officer will make their full text available. The offeror is cautioned that the listed provisions may include blocks that must be completed by the offeror and submitted with its quotation or offer. In lieu of submitting the full text of those provisions, the offeror may identify the provision by paragraph identifier and provide the appropriate information with its quotation or offer. Also, the full text of a solicitation provision may be accessed electronically at this/these address(es):

FAR FAR | Acquisition.GOV NFS NASA FAR Supplement

FEDERAL ACQUISITION REGULATION (FAR) PROVISIONS INCORPORATED BY

REFERENCE:

☒52.204-7 System for Award Management (APR 2026)(DEVIATION) ☒52.209-2 Prohibition on Contracting with Inverted Domestic Corporations – Representation (APR

2026)(DEVIATION)

FAR PROVISIONS IN FULL TEXT:

☒52.225-8 Duty-Free Entry (OCT 2010)

(a) Definition. "Customs territory of the United States" means the States, the District of Columbia, and Puerto Rico.

(b) Except as otherwise approved by the Contracting Officer, the Contractor shall not include in the contract price any amount for duties on supplies specifically identified in the Schedule to be accorded duty-free entry.

(c) Except as provided in paragraph (d) of this clause or elsewhere in this contract, the following procedures apply to supplies not identified in the Schedule to be accorded duty-free entry:

(1) The Contractor shall notify the Contracting Officer in writing of any purchase of foreign supplies (including, without limitation, raw materials, components, and intermediate assemblies) in excess of $20,000 that are to be imported into the customs territory of the United States for delivery to the Government under this contract, either as end products or for incorporation into end products. The Contractor shall furnish the notice to the Contracting Officer at least 20 calendar days before the importation. The notice shall identify the-

(i) Foreign supplies;

(ii) Estimated amount of duty; and

8 V12 APR 2026

(iii) Country of origin.

(2) The Contracting Officer will determine whether any of these supplies should be accorded duty-free entry and will notify the Contractor within 10 calendar days after receipt of the Contractor’s notification.

(3) Except as otherwise approved by the Contracting Officer, the contract price shall be reduced by (or the allowable cost shall not include) the amount of duty that would be payable if the supplies were not entered duty-free.

(d) The Contractor is not required to provide the notification under paragraph (c) of this clause for purchases of foreign supplies if-

(1) The supplies are identical in nature to items purchased by the Contractor or any subcontractor in connection with its commercial business; and

(2) Segregation of these supplies to ensure use only on Government contracts containing duty-free entry provisions is not economical or feasible.

(e) The Contractor shall claim duty-free entry only for supplies to be delivered to the Government under this contract, either as end products or incorporated into end products, and shall pay duty on supplies, or any portion of them, other than scrap, salvage, or competitive sale authorized by the Contracting Officer, diverted to nongovernmental use.

(f) The Government will execute any required duty-free entry certificates for supplies to be accorded duty-free entry and will assist the Contractor in obtaining duty-free entry for these supplies.

(g) Shipping documents for supplies to be accorded duty-free entry shall consign the shipments to the contracting agency in care of the Contractor and shall include the-

(1) Delivery address of the Contractor (or contracting agency, if appropriate);

(2) Government prime contract number;

(3) Identification of carrier;

(4) Notation "UNITED STATES GOVERNMENT, _____ [agency] _____, Duty-free entry to be claimed pursuant to Item No(s) _____ [from Tariff Schedules] _____, Harmonized Tariff Schedules of the United States. Upon arrival of shipment at port of entry, District Director of Customs, please release shipment under 19 CFR part 142 and notify [cognizant contract administration office] for execution of Customs Forms 7501 and 7501-A and any required duty-free entry certificates.";

(5) Gross weight in pounds (if freight is based on space tonnage, state cubic feet in addition to gross shipping weight); and

(6) Estimated value in United States dollars.

(h) The Contractor shall instruct the foreign supplier to-

(1) Consign the shipment as specified in paragraph (g) of this clause;

9 V12 APR 2026

(2) Mark all packages with the words "UNITED STATES GOVERNMENT" and the title of the contracting agency; and

(3) Include with the shipment at least two copies of the bill of lading (or other shipping document) for use by the District Director of Customs at the port of entry.

(i) The Contractor shall provide written notice to the cognizant contract administration office immediately after notification by the Contracting Officer that duty-free entry will be accorded foreign supplies or, for duty-free supplies identified in the Schedule, upon award by the Contractor to the overseas supplier. The notice shall identify the-

(1) Foreign supplies;

(2) Country of origin;

(3) Contract number; and

(4) Scheduled delivery date(s).

(j) The Contractor shall include the substance of this clause in any subcontract if-

(1) Supplies identified in the Schedule to be accorded duty-free entry will be imported into the customs territory of the United States; or

(2) Other foreign supplies in excess of $20,000 may be imported into the customs territory of the United States.

(End of clause)

NFS 1852.225-8(k): The following supplies will be given duty-free entry:

(End of addition)

☐52.225-18 PLACE OF MANUFACTURE (AUG 2018)

(a) Definitions. As used in this clause— “Manufactured end product” means any end product in product and service codes (PSCs) 1000-9999, except—

(1) FPSC 5510, Lumber and Related Basic Wood Materials;

(2) Product or Service Group (PSG) 87, Agricultural Supplies;

(3) PSG 88, Live Animals;

(4) PSG 89, Subsistence;

(5) PSC 9410, Crude Grades of Plant Materials;

(6) PSC 9430, Miscellaneous Crude Animal Products, Inedible;

(7) PSC 9440, Miscellaneous Crude Agricultural and Forestry Products;

(8) PSC 9610, Ores;

10 V12 APR 2026

(9) PSC 9620, Minerals, Natural and Synthetic; and

(10) PSC 9630, Additive Metal Materials.

“Place of manufacture” means the place where an end product is assembled out of components, or otherwise made or processed from raw materials into the finished product that is to be provided to the Government. If a product is disassembled and reassembled, the place of reassembly is not the place of manufacture.

(b) For statistical purposes only, the offeror shall indicate whether the place of manufacture of the end products it expects to provide in response to this solicitation is predominantly—

(1)In the United States (Check this box if the total anticipated price of offered end products manufactured in the United States exceeds the total anticipated price of offered end products manufactured outside the United States); or

(2) Outside the United States.

(End of provision)

11 V12 APR 2026

SECTION 4

CLAUSES/TERMS AND CONDITIONS

APPLICABLE COMMERCIAL ITEM CLAUSES

This order is for a commercial item subject to the terms and conditions of FAR 52.212-4, Terms and Conditions

– Commercial Products and Commerical Serivces (APR 2026)(DEVIATION), incorporated by reference attached to this order and any additional terms and conditions checked below or included as a Center specific requirements as addenda to 52.212-4.

☒52.252-2 CLAUSES INCORPORATED BY REFERENCE (FEB 1998).

This contract incorporates one or more clauses by reference, with the same force and effect as if they were given in full text. Upon request, the Contracting Officer will make their full text available. Also, the full text of a clause may be accessed electronically at this/these address(es): FAR and NFS Search (nasa.gov)

FAR CLAUSES INCOPORATED BY REFERENCE:

☒52.204-9 Personal Identity Verification of Contractor Personnel (JAN 2011) ☒52.204-13 System for Award Management Maintenance (APR 2026)(DEVIATION) ☒ 52 .222-90 Addressing DEI Discrimination by Federal Contractors (APR 2026)(DEVIATION) ☒52.223-23 Sustainable Products and Services (APR 2026)(DEVIATION) ☒52.232-39 Unenforceability of Unauthorized Obligations (JUN 2013) ☒52.232-40 Providing Accelerated Payments to Small Business Subcontractors (MAR 2023) ☐52.245-1 Government Property (SEP 2021) ☐52.247-29 F.o.b. Origin (FEB 2006) ☒52.247-34 F.o.b. Destination (NOV 1991)

NASA FEDERAL ACQUISITION REGULATION (NFS) CLAUSES INCORPORATED BY

REFERENCE:

☒1852.203-71 Requirements to Inform Employees of Whistleblower rights (SEP

2025)(DEVIATION)

☒1852.237-73 Release of Sensitive Information (DEC 2025)(DEVIATION) ☐1852.245-76 List of government property furnished pursuant to FAR 52.245-2 (DEC

2025)(DEVIATION)

☐1852.242-72 Denied Access to NASA Facilities (DEC 2025)(DEVIATION)

NFS CLAUSES IN FULL TEXT:

☒1852.215-84 OMBUDSMAN (NOV 2023)

12 V12 APR 2026

(a) An ombudsman has been appointed to hear and facilitate the resolution of concerns from offerors, potential offerors, and contractors during the preaward and postaward phases of this acquisition. When requested, the ombudsman will maintain strict confidentiality as to the source of the concern. The existence of the ombudsman is not to diminish the authority of the contracting officer, the Source Evaluation Board, or the selection official.

Further, the ombudsman does not participate in the evaluation of proposals, the source selection process, or the adjudication of formal contract disputes. Therefore, before consulting with an ombudsman, interested parties must first address their concerns, issues, disagreements, and/or recommendations to the contracting officer for resolution.

(b) If resolution cannot be made by the contracting officer, interested parties may contact the installation ombudsman, whose name, address, telephone number, facsimile number, and email address may be found at:

https://www.hq.nasa.gov/office/procurement/regs/ProcurementOmbuds-Comp-Advocate-Listing.pdf. Concerns, issues, disagreements, and recommendations which cannot be resolved at the installation may be referred to the Agency ombudsman identified at the above URL. Please do not contact the ombudsman to request copies of the solicitation, verify offer due date, or clarify technical requirements. Such inquiries shall be directed to the Contracting Officer or as specified elsewhere in this document.

☒1852.216-78 FIRM FIXED PRICED (DEC 2025)(DEVIATION)

The total firm-fixed-price of this contract TBD.

☒1852.225-70 EXPORT LICENSES (DEC 2025)(DEVIATION)

(a) The contractor shall comply with all U.S. export control laws and regulations, including the International Traffic in Arms Regulations (ITAR), 22 CFR Parts 120 through 130, and the Export Administration Regulations (EAR), 15 CFR Parts 730 through 799, in the performance of this contract. In the absence of available license exemptions/exceptions, the contractor shall be responsible for obtaining the appropriate licenses or other approvals, if required, for exports of hardware, technical data, and software, or for the provision of technical assistance.

(b) The contractor shall be responsible for obtaining export licenses, if required, before utilizing foreign persons in the performance of this contract, including instances where the work is to be performed on-site at AFRC, where the foreign person will have access to export-controlled technical data or software.

(c) The contractor shall be responsible for all regulatory record keeping requirements associated with the use of licenses and license exemptions/exceptions.

(d) The contractor shall be responsible for ensuring that the provisions of this clause apply to its subcontractors.

13 V12 APR 2026

SECTION 5

QUOTE EVALUATION CRITERIA

The Government will award a contract from this solicitation to the responsible Offeror whose offer conforming to the solicitation is the lowest price technically acceptable (LPTA) offer. Offer’s not deemed technically acceptable will be removed from further consideration of the contract award. An Offeror’s quote will be deemed technically unacceptable and removed from further consideration for contract award if the Offeror’s quote does not demonstrate that all of the requirements listed in this solicitation can be met in a satisfactory manner.