ResCheck - Building B - STAMPED.pdf

Report Title: PROJECT 23135-3 - BUILDING 'B' Report Date: 12/13/25, 3:32 AM

Compliance Certificate

Project Information

Project Title:

Energy Code:

Location:

Construction Type:

Project Type:

Project Sub Type:

Orientation:

Conditioned Floor Area:

Glazing Area:

Climate Zone:

Project No:

All Electric:

Is Renewable:

Has Battery:

Has Charger:

Has Heat Pump

PROJECT 23135-3 - BUILDING 'B'

2020 NYStretch - 2018 IECC

Macedon, New York

Multi-family

New Construction

None

Bldg. faces 180 deg. from North

4638 ft2

10%

5a (6672 HDD)

1802123 true false false false false

Construction Site: Owner/Agent: Designer/Contractor:

WEST ST

MACEDON

, NY

BUILDING 'A'

GERBER HOMES

Project Notes:

12/13/2025

Envelope Assemblies

Assembly Gross Area or Perimeter

Cavity

R-Value

Cont.

R-Value

Prop.

U-

Factor/

F-Factor

Req.

U-

Factor/

F-Factor

Prop.

UA

Req.

UA

over garage: Flat Ceiling or

Scissor Truss

670 30.0 0.0 0.035 0.026 23 17

Ceiling: Raised or Energy

Truss

2645 19.0 41.0 0.016 0.026 42 69

Floor: All-Wood Joist/Truss 112 30.0 0.0 0.033 0.033 4 4

Wall: Wood Frame, 24" o.c.

Orientation: Front

3997 21.0 0.0 0.056 0.045 190 153

Window 2: Vinyl Frame

SHGC: 0.34

360 0.300 0.270 108 97

Sliders: Solid Door (under

50% glazing)

122 0.300 0.270 37 33

Garage and front door: Solid

Door (under 50% glazing)

126 0.166 0.270 21 34

Basement Wall: Masonry

Block w/ Empty Cells

Wall height: 8.00

Insulation depth: 8.00'

Insulation position: Integral

Insulation

1868 0.0 19.0 0.036 0.050 66 91

Window: Vinyl Frame

SHGC: 0.34

48 0.300 0.270 14 13

Compliance: Passes using UA trade-off

Compliance: 1.2% Better Than Code Max UA:

Your UA: 505 Your SHGC: 0.34

The % Better or Worse Than Code Index reflects how close to compliance the house is based on code trade-off rules. It DOES

NOT provide an estimate of energy use or cost relative to a minimum-code home.

Slab-on-grade tradeoffs are no longer considered in the UA or performance compliance path in REScheck. Each slab-on-grade assembly in the specified climate zone must meet the minimum energy code insulation R-value and depth requirements.

Compliance Statement

The proposed building design described here is consistent with the building plans, specifications, and other calculations submitted with the permit application. The proposed building has been designed to meet the 2020 NYStretch - 2018 IECC requirements in REScheck-Web and to comply with the mandatory requirements listed in the REScheck Inspection Checklist.

Name - Title Signature Date

Inspection Checklist

Energy Code: 2020 NYStretch - 2018 IECC

Requirements: 85% were addressed directly in the REScheck software

Text in the "Comments/Assumptions" column is provided by the user in the REScheck Requirements screen. For each requirement, the user certifies that a code requirement will be met and how that is documented, or that an exception is being claimed. Where compliance is itemized in a separate table, a reference to that table is provided.

Pre-Inspection/Plan Review

Section

& Req.ID Pre-Inspection/Plan Review

Plans

Verified

Value

Field

Verified

Value Complies? Comments/Assumptions

103.1, 103.2

[PR1]1

Construction drawings and documentation demonstrate energy code compliance for the building envelope. Thermal envelope represented on construction documents.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

103.1, 103.2, 403.7

[PR3]1

Construction drawings and documentation demonstrate energy code compliance for lighting and mechanical systems. Systems serving multiple dwelling units must demonstrate compliance with the IECC Commercial Provisions.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

302.1, 403.7

[PR2]2

Heating and cooling equipment is sized per ACCA Manual S based on loads calculated per

ACCA Manual J or other methods approved by the code official.

Heating:

Btu/hr

Cooling:

Heating:

Cooling:

Complies

Does Not

Comply

Not

Observable

Not

Applicable

Additional Comments/Assumptions:

1 High Impact (Tier 1) 2 Medium Impact (Tier 2) 3 Low Impact (Tier 3)

Foundation Inspection

Section

& Req.ID Foundation Inspection

Plans

Verified

Value

Field

Verified

Value Complies? Comments/Assumptions

303.2.1

[FO11]2

A protective covering is installed to protect exposed exterior insulation and extends a minimum of 6 in. below grade.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

403.9

[FO12]2

Snow- and ice-melting system controls installed.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

402.1.1

[FO4]1

Conditioned basement wall insulation R-value. Where interior insulation is used, verification may need to occur during Insulation Inspection. Not required in warm-humid locations in Climate Zone 3.

R-

R-

R-

R-

Complies

Does Not

Comply

Not

Observable

Not

Applicable

See the Envelope

Assemblies table for values

303.2

[FO5]1

Conditioned basement wall insulation installed per manufacturer’s instructions.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

402.2.9

[FO6]1

Conditioned basement wall insulation depth of burial or distance from top of wall.

ft ft Complies

Does Not

Comply

Not

Observable

Not

Applicable

See the Envelope

Assemblies table for values

Framing / Rough-In Inspection

Section

& Req.ID

Framing / Rough-In

Inspection

Plans

Verified

Value

Field

Verified

Value Complies? Comments/Assumptions

402.1.1, 402.3.4

[FR1]1

Door U-factor.

U- U-

Complies

Does Not

Comply

Not

Observable

Not

Applicable

See the Envelope

Assemblies table for values

402.1.1, 402.3.1, 402.3.3, 402.5

[FR2]1

Glazing U-factor (area-weighted average).

U- U-

Complies

Does Not

Comply

Not

Observable

Not

Applicable

See the Envelope

Assemblies table for values

402.4.1.1

[FR23]1

Air barrier and thermal barrier installed per manufacturer’s instructions. An approved third-party will inspect all components and verify compliance. See section details and guidance from Table

R402.4.1.1.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

402.4.3

[FR20]1

Fenestration that is not site built is listed and labeled as meeting

AAMA /WDMA/CSA

101/I.S.2/A440 or has infiltration rates per NFRC 400 that do not exceed code limits.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

402.4.5

[FR16]2

IC-rated recessed lighting fixtures sealed at housing/interior finish and labeled to indicate ≤2.0 cfm leakage at 75 Pa.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

403.3.1

[FR12]1

Supply and return ducts in attics insulated >= R-8 where duct is

>= 3 inches in diameter and

>= R-6 where < 3 inches.

Supply and return ducts in other portions of the building insulated >= R-6 for diameter

>= 3 inches and R-4.2 for < 3 inches in diameter.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

403.3.2

[FR13]1

Ducts, air handlers and filter boxes are sealed with joints/seams compliant with

International Mechanical Code or International Residential

Code, as applicable.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

403.3

[FI32]1

Duct system in new buildings and additions are located in a conditioned space in accordance with Sections

R403.3.7 (1-2).

Complies

Does Not

Comply

Not

Observable

Not

Applicable

Section

& Req.ID

Framing / Rough-In

Inspection

Plans

Verified

Value

Field

Verified

Value Complies? Comments/Assumptions

403.3.8

[FI33]1

Ducts are sized in accordance with ACCA Manual D and sections R403.7-8.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

403.3.5

[FR15]3

Building cavities are not used as ducts or plenums.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

403.3.7

[FR28]3

Ducts declared to be within the conditioned space are either 1) completely within the continuous air barrier and within the building thermal envelope,

2) buried within ceiling insulation in accordance with

Section R403.3.6 and the air handler is located completely within the continuous air barrier and within the building thermal envelope and the duct leakage is <= 1.5 cfm / 100 square feet of conditioned floor area served by the duct system, or 3) the ceiling insulation R-value installed against and above the insulated duct >= to the proposed ceiling insulation R-value, less the R-value of the insulation on the duct.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

403.4

[FR17]2

HVAC piping conveying fluids above 105 ºF or chilled fluids below 55 ºF are insulated to ≥R-

3.

R- R- Complies

Does Not

Comply

Not

Observable

Not

Applicable

403.4.1

[FR24]1

Protection of insulation on HVAC piping.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

403.5.3

[FR18]2

Hot water pipes are insulated to

≥R-3.

R- R-

Complies

Does Not

Comply

Not

Observable

Not

Applicable

403.5

[FR29]2

Energy conservation measures for SWH systems follow guidelines in section R403.5.1-

5.

R- R- Complies

Does Not

Comply

Not

Observable

Not

Applicable

403.6

[FR19]2

Automatic or gravity dampers are installed on all outdoor air intakes and exhausts.

Complies

Does Not

Comply

Not

Observable

& Req.ID

Framing / Rough-In

Inspection

Plans

Verified

Value

Field

Verified

Value Complies? Comments/Assumptions

303.1.3

[FR4]1

U-factors of fenestration products are determined in accordance with the NFRC test procedure or taken from the default table.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

Insulation Inspection

Section

& Req.ID Insulation Inspection

Plans

Verified

Value

Field

Verified

Value Complies? Comments/Assumptions

303.1

[IN13]2

All installed insulation is labeled or the installed R-values provided.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

402.1.1, 402.2.6

[IN1]1

Floor insulation R-value.

R-

Wood

Steel

R-

Wood

Steel

Complies

Does Not

Comply

Not

Observable

Not

Applicable

See the Envelope

Assemblies table for values

303.2, 402.2.8

[IN2]1

Floor insulation installed per manufacturer’s instructions and in substantial contact with the underside of the subfloor, or floor framing cavity insulation is in contact with the top side of sheathing, or continuous insulation is installed on the underside of floor framing and extends from the bottom to the top of all perimeter floor framing members.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

402.1.1, 402.2.5, 402.2.6

[IN3]1

Wall insulation R-value. If this is a mass wall with at least ½ of the wall insulation on the wall exterior, the exterior insulation requirement applies (FR10).

R-

Wood

Mass

Steel

R-

Wood

Mass

Steel

Complies

Does Not

Comply

Not

Observable

Not

Applicable

See the Envelope

Assemblies table for values

303.2

[IN4]1

Wall insulation is installed per manufacturer’s instructions.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

Final Inspection Provisions

Section

& Req.ID Final Inspection Provisions

Plans

Verified

Value

Field

Verified

Value Complies? Comments/Assumptions

402.1.1, 402.2.1, 402.2.2, 402.2.6

[FI1]1

Ceiling insulation R-value.

R-

Wood

Steel

R-

Wood

Steel

Complies

Does Not

Comply

Not

Observable

Not

Applicable

See the Envelope

Assemblies table for values

303.1.1.1, 303.2

[FI2]1

Ceiling insulation installed per manufacturer’s instructions.

Blown insulation marked every

300 ft².

Complies

Does Not

Comply

Not

Observable

Not

Applicable

403.1.2

[FI10]2

Heat pump thermostat installed on heat pumps.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

403.5.1

[FI11]2

Circulating service hot water systems have automatic or accessible manual controls.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

403.6.1

[FI25]2

All mechanical ventilation system fans not part of tested and listed HVAC equipment meet efficacy and air flow limits per Table R403.6.1.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

403.6.2

[FI34]2

Every dwelling unit is served by a heat recovery ventilator (HRV) or energy recovery ventilator

(ERV) installed per manufacturer’s instructions. The

HRV/ERV is listed and sized adequately for the specific application, which will include the building’s conditioned area, and number of occupants.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

403.6.3

[FI35]2

Installed performance of the mechanical ventilation system is tested and verified by an approved agency and measured using a flow hood, flow grid, or other airflow measuring device.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

403.2

[FI26]2

Hot water boilers supplying heat through one- or two-pipe heating systems have outdoor setback control to lower boiler water temperature based on outdoor temperature.

Complies

Does Not

Comply

Not

Observable

& Req.ID Final Inspection Provisions

Plans

Verified

Value

Field

Verified

Value Complies? Comments/Assumptions

403.5.1.1

[FI28]2

Heated water circulation systems have a circulation pump. The system return pipe is a dedicated return pipe or a cold water supply pipe. Gravity and thermos-syphon circulation systems are not present.

Controls for circulating hot water system pumps start the pump with signal for hot water demand within the occupancy.

Controls automatically turn off the pump when water is in circulation loop is at set-point temperature and no demand for hot water exists.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

403.5.1.2

[FI29]2

Electric heat trace systems comply with IEEE 515.1 or UL

515. Controls automatically adjust the energy input to the heat tracing to maintain the desired water temperature in the piping.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

403.5.2

[FI30]2

Demand recirculation water systems have controls that manage operation of the pump and limit the temperature of the water entering the cold water piping to <= 104ºF.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

403.5.4

[FI31]2

Drain water heat recovery units have >= 40 percent efficiency if installed for equal flow or >=52 percent efficiency if installed for unequal flow. Vertical drain water heat recovery units comply with CSA B55.2 and tested and labeled in accordance with CSA B55.1.

Potable water-side pressure loss of drain water heat recovery units are < 3 psi for individual units connected to one or two showers. Potable water-side pressure loss of drain water heat recovery units are < 2 psi for individual units connected to three or more showers.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

403.5.5(1-

4)

[FI33]2

Heated water supply piping is in acccordance with one of the following: 1) Maximum allowable pipe length method,

2) Maximum allowable pipe volume mehtod, 3) Drain water heat recovery units, or 4)

Recirculation Systems.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

404.1

[FI6]1

90% or more of permanent fixtures have lamps with an efficacy >= 65 lumans/watt or have a total luminaire efficacy

>= 45 lumens/watt.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

404.2

[FI35]1

Detached one and two-family dwellings and townhouses where the conditioned space is

> 1,400 sf comply with the requirements of Appendix RA.

Complies

Does Not

Comply

Not

Observable

& Req.ID Final Inspection Provisions

Plans

Verified

Value

Field

Verified

Value Complies? Comments/Assumptions

404.3

[FI36]1

One or two-family dwellings and townhouses with parking area provided on the building site shall have a 208/240V 40-amp outlet for each dwelling unit or panel capacity and conduit for the future installation of such an outlet. See section details.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

404.1.1

[FI23]3

Fuel gas lighting systems have no continuous pilot light.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

401.3

[FI7]2

Compliance certificate posted. Complies

Does Not

Comply

Not

Observable

Not

Applicable

303.3

[FI18]3

Manufacturer manuals for mechanical and water heating systems have been provided.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

402.2.3

[FI22]2

Vented attics with air permeable insulation include baffle adjacent to soffit and eave vents that extends over insulation.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

402.2.4

[FI3]1

Attic access hatch and door insulation ≥R-value of the adjacent assembly.

R- R- Complies

Does Not

Comply

Not

Observable

Not

Applicable

402.4.1.2

[FI17]1

Blower door test @ 50 Pa. <=5 ach in Climate Zones 1-2, and

<=3 ach in Climate Zones 3-8.

ACH 50 =

ACH 50 =

Complies

Does Not

Comply

Not

Observable

Not

Applicable

403.3.3

[FI27]1

Ducts are pressure tested to determine air leakage with either:

Rough-in test: Total leakage measured with a pressure differential of 0.1 inch w.g. across the system including the manufacturer’s air handler enclosure if installed at time of test.

Postconstruction test: Total leakage measured with a pressure differential of 0.1 inch w.g. across the entire system including the manufacturer’s air handler enclosure.

cfm/100 ft cfm/100 ft

Complies

Does Not

Comply

Not

Observable

& Req.ID Final Inspection Provisions

Plans

Verified

Value

Field

Verified

Value Complies? Comments/Assumptions

403.3.4

[FI4]1

Duct tightness test result of

<=4 cfm/100 ft2 across the system or <=3 cfm/100 ft2 without air handler @ 25 Pa. For rough-in tests, verification may need to occur during Framing

Inspection.

cfm/100 ft cfm/100 ft

Complies

Does Not

Comply

Not

Observable

Not

Applicable

403.3.2.1

[FI24]1

Air handler leakage designated by manufacturer at <=2% of design air flow.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

403.1.1

[FI9]2

Programmable thermostats installed for control of primary heating and cooling systems and initially set by manufacturer to code specifications.

Complies

Does Not

Comply

Not

Observable

Not

Applicable

2020 NYStretch -

2018 IECC Energy

Efficiency

Certificate

Insulation Rating R-Value

Above-Grade Wall 21.00

Below-Grade Wall 19.00

Floor 30.00

Ceiling / Roof 60.00

Ductwork (unconditioned spaces): _____

Glass & Door Rating U-Factor SHGC

Window 0.30 0.34

Door 0.17

Skylight 0.00

Heating & Cooling Equipment Efficiency

Heating System: ______________________ ______________________

Cooling System: ______________________ ______________________

Water Heater: ______________________ ______________________

Signature

Name: ______________________ Date: ______________________

Comments: