PWS_OCMM.pdf
PDF 189 KB Posted
- Attached to
- Starrett Optical Coordinate Measuring Machine Federal contract opportunity
- Solicitation number
- SP4706-26-Q-0XXX
- Issued by
- Defense Logistics Agency
About this file
This is a Performance Work Statement for the procurement of an Optical Coordinate Measuring Machine (OCMM) by the DLA Product Test Center Division, Electronics Lab in Columbus, Ohio, dated 12 April 2024.
The primary objective is to procure and install one Starrett AVR300 Optical Inspection CMM system with workstation to expand the Electronics Product Test Center's (EPTC) optical measuring capacity, accuracy, and efficiency. The EPTC currently relies on the single OCMM located at the Mechanical Product Test Center (MPTC), which creates bottlenecks in test cycle time and project turnaround. The contractor shall be responsible for installation, calibration, and on-site training for up to five laboratory associates over one day. The deliverable is the Starrett AVR300 system. Installation and work will be performed at Building 11, Section 7, DSCC Columbus, 3990 East Broad Street, Whitehall, OH 43213, with shipment receivable to Building 17 and marked for Building 11, Section 7, attention Kedric Jones. Invoicing will be submitted through the Wide Area Workflow (WAWF) system to the Defense Finance and Accounting Service within 10 workdays after training conclusion, with the DODAAC# SL0700. The Government Contract Officer Representative is Kyle Palmer (614-692-8860, Kyle.Palmer@dla.mil), and the Technical Representative/Project Manager is Kedric Jones (614-693-0776, kedric.jones@dla.mil). No applicable directives or line-item travel costs are specified.
View the file
Other files for this federal contract opportunity
| File | Type | Posted |
|---|---|---|
| TECH_SPECS_OCMM.pdf |
On GovTribe
Work with this file on GovTribe
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
PERFORMANCE WORK STATEMENT
1. Electronics Test Lab
12 April 2024
Requiring Activity: DLA Product Test Center Division, Electronics Lab, located at
Columbus, Ohio. Contracting Activity: DLA Contracting Services located in Columbus, Ohio.
2. Introduction
This is a description of the DLA Product Test Center (PTC) Division, Electronic Lab, requirements for the procurement of an Optical Coordinate Measuring Machine (OCMM). It is the intent here to clearly define all required performance characteristics. In generating this statement, our objective is to end up with an OCMM which expands our overall testing capability of inspecting intricate parts, in both accuracy and efficiency. Because we want to maximize the ease of use some of the required features listed below will be specific. Our general objective is to minimize any impact to the DLA Product Test Center Division, Electronic Lab operations and our customers because of this procurement, especially with regards to test cycle time. This system will decrease time required to inspect delicate parts and reduce any human errors possible with current measurements.
3. Background
This machine would increase Electronic Product Test Center’s (EPTC’s) measuring efficiency and accuracy, help improve measuring turnaround time, and provide a new way of measuring the EPTC that could only be done before by sending a project to the Mechanical Product Test
Center (MPTC). Most importantly procurement of this machine will increase our current optical measuring capacity as currently MPTC has one OCMM. Not procuring this piece of equipment would continue to increase cycle time on all projects that require an OCMM to get the dimensional data as the EPTC would have to wait for the one in the MPTC to become available for use.
4. Scope
The installation and calibration of one (1) Starrett Optical Inspection CMM with workstation. One day of on-site training for up to five (5) laboratory associates.
5. Applicable Directives
None
6. Performance Requirements
The Contractor shall install, calibrate, and provide on-site training for the Optical Coordinate
Measuring Machine and workstation.
7. Deliverables
The Starrett AVR300 system.
8. Place of Performance
DSCC Columbus
Building 11 Section 7
3990 East Broad Street
Whitehall, OH 43213
Shipped receivable to Bldg 17
Marked for Bldg 11 section 7
Attn: Kedric Jones (+1 614-693-0776)
Work to be performed will take place at:
Building 11, Section 7
9. Travel (if applicable)
No line-item travel was itemized in quote.
10. Invoicing
Payment of invoices will be accomplished by payment through the Defense Finance and Accounting
Service. Invoices will be submitted to the Wide Area Workflow system in accordance with DFARS
252.232-7003-Electronic Submission of Payment Requests and Receiving Reports and DFARS
252.232- 7006 Wide Area Workflow Payment Instructions within 10 workdays after the conclusion of each training session.
11. WAWF Acceptance DODAAC#
Electronics Product
Test Center is
SL0700.
12. Point of Contacts
The Government Contract Officer:
TBD
The Government Contract Officer Representative (COR):
Kyle Palmer Kyle.Palmer@dla.mil
614-692-8860
DLA Land and Maritime Product Test Center, V Office
3990 E. Broad St., Columbus, OH Bldg. 11, Section 7
Kedric Jones +1 614-693-0776
The Government Technical Representative/Project Manager:
Name: Kedric Jones
Email: kedric.jones@dla.mil mailto:Kyle.Palmer@dla.mil
File details come from the government source that posted it. Updated .