PWS-CGM.pdf
PDF 286 KB Posted
- Attached to
- Circular Geometry Machine (CGM) Roundness Tester
- Solicitation number
- SP4706-26-Q-XX13
- Issued by
-
Defense Logistics Agency
About this file
This is a Performance Work Statement for the procurement of a Circular Geometry Machine (CGM) by the DLA Product Test Center Division, Mechanical Lab (VTM) in Columbus, Ohio, dated 24 February 2026.
The contractor must deliver one new CGM with all required accessories and provide installation, setup, and calibration at Building 9, Section 1 of DSCC Columbus (3990 East Broad Street, Whitehall, OH 43213). The contractor is also responsible for delivering one day of training for up to five Product Test Center associates. The primary objectives are to expand VTM's testing capability for round parts by improving both accuracy and efficiency, minimize impact on current operations and test cycle time, and replace the existing obsolete CGM. All travel costs are the contractor's responsibility. Invoices must be submitted to the Wide Area Workflow system within 10 work days after the conclusion of each training session, in accordance with DFARS 252.232-7003 and DFARS 252.232-7006, with payment processed through the Defense Finance and Accounting Service. The DoDAAC for the TM Lab is SL0702. The Government Contract Officer Representative is Kyle Palmer (Kyle.Palmer@dla.mil, 614-693-5055), while the Government Contract Officer is to be determined. Equipment should be shipped to Building 17 and marked for Building 9 Section 1, attention Tom Morley (614-693-0020).
View the file
Other files
| File | Type | Posted |
|---|---|---|
| TECH-SPECS-CGM.pdf |
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
PERFORMANCE WORK STATEMENT
24 February 2026
Requiring Activity: DLA Product Test Center Division, Mechanical Lab (VTM), located in
Columbus, Ohio. Contracting Activity: DLA Contracting Services located in Columbus, Ohio.
1. Introduction
This is a description of the DLA Product Test Center Division, Mechanical Lab, VTM, requirements for the procurement of a Circular Geometry Machine (CGM). It is the intent here to clearly define all required performance characteristics. In generating this statement, our objective is to end up with a CGM which expands our overall testing capability of inspecting round parts, in both accuracy and efficiency. Our general objective is to minimize any impact on the DLA Product Test Center Division, Mechanical Lab, VTM, operations and our customers as a result of this procurement, especially with regards to test cycle time. This system will decrease time required to inspect round parts and remove any human errors possible with current measurement.
2. Background
This machine would increase VTM’s measuring efficiency and accuracy, help improve measuring turnaround time, and replace the current obsolete CGM. Most importantly procurement of this machine will increase our current CGM measuring capacity. Not procuring this piece of equipment would leave VTM with an obsolete CGM.
3. Scope
The installation, set up, and calibration of one (1) CGM. The contractor will also provide one
(1) day of training for up to five (5) Product Test Center associates.
4. Applicable Directives
None
5. Performance Requirements
The Contractor will install, setup, calibrate, and provide training on the new CGM in the
Mechanical Product Test Center.
6. Deliverables
New CGM and all required accessories, including installation, setup, calibration and training.
7. Place of Performance
DSCC Columbus
Building 9 Section 1
3990 East Broad Street Whitehall, OH 43213
Shipped receivable to Bldg. 17
Marked for Bldg. 9 section 1
Attn: Tom Morley 614-693-0020
Work to be performed will take place at: Building 9, Section 1
8. Travel
Contractor is responsible for all required travel.
9. Invoicing
Payment of invoices will be accomplished by payment through the Defense Finance and
Accounting Service. Invoices will be submitted to the Wide Area Workflow system in accordance with DFARS 252.232-7003-Electronic Submission of Payment Requests and
Receiving Reports and DFARS 252.232- 7006 Wide Area Workflow Payment Instructions within 10 work days after the conclusion of each training session.
10. WAWF Acceptance DODAAC#
TM Lab is DoDAAC SL0702.
11. Point of Contacts
The Government Contract Officer:
TBD
The Government Contract Officer Representative (COR):
Kyle Palmer Kyle.Palmer@dla.mil
(614) 693-5055 mailto:Kyle.Palmer@dla.mil
File details come from the government source that posted it. Updated .