DEPARTMENT OF THE ARMY

249TH ENGINEER BATTALION (PRIME POWER)

BUILDING 1416, JACKSON LOOP

FORT BELVOIR, VIRGINIA 22060

CEPP-LO 4 August 2026

MEMORANDUM FOR RECORD

Subject: Performance Work Statement for 249th Engineer Battalion Electrical Test

Equipment Calibration

1. General Information. The 249th Engineer Battalion (Prime Power) requires calibration services for electrical test equipment that is not supported by the US Army Test, Measurement, and Diagnostic Equipment (TMDE) Activity. Henceforth, within this document, the terms “TMDE” and “Equipment” are synonymous and interchangeable.

The TMDE items are dispersed between Fort Belvoir, Virginia; and Fort Bragg, North Carolina.

2. Background. The 249th EN BN (PP) installs, operates, and maintains power production and distribution systems worldwide. In order to support the operation, and maintenance of these systems, electrical test equipment that is not held within the US Army’s inventory is required and must be supported outside of the existing system.

3. Definition. Proper terminology is important to understand our requirements.

Henceforth, “mobile calibration” or “onsite calibration” is defined as the act of the Contractor driving from their location to our location, where they perform calibration and repair services onsite at our location. “Mobile pickup and delivery” is defined as the act of the Contractor driving from their location to our location, where they retrieve our items requiring calibration and/or repair, then transport our equipment to their location for calibration and/or repair, then transport our completed equipment back its respective location. “Government drop off and pickup” is defined as the act of the 249th EN BN driving from their location to the Contractor’s location, where they drop off our items requiring calibration and/or repair, then retrieve our equipment from the Contractor’s location after calibration and/or repair is completed.

4. Scope. The Contractor will calibrate the following items:

Megger DLRO-H200 (Digital Low Resistance Micro-Ohmmeter)

Megger INGVAR (Primary Current injection Test System)

Megger MIT525 (5kV DC Insulation Resistance Tester)

Megger MRCT-S0R0R1A4M0S and MRCT-S0C0R1A2M0S (Relay and Current Transformer Test Set)

Megger MTO-210 (Transformer Ohmmeter)

Megger PA-9 (Power Quality Analyzer)

CEPP-LO

SUBJECT: Performance Work Statement for 249th Engineer Battalion Electrical Test

Fluke 190-204 (Power Quality Analyzer, Data Logger)

H.V.I. PFT503CM (AC High Voltage Dielectric Test Set)

Megger S1-568 (5kV DC Insulation Resistance Tester)

Megger SMRT36 (Relay Test Set)

Megger TTR20 (Handheld Transformer Turn Ratio)

Megger TTR-310 (Transformer Turns Ratio Tester)

Megger VIDAR (Vacuum Breaker Tester)

Megger TTRU-3-ADV (True Three Phase TTR Tester)

Fluke 1775 (Three Phase Power Quality Analyzer)

Megger TTR20-1 (Handheld Transformer Turn Ratio)

FLIR T840 (Thermal Camera)

Megger VLF-34 (Hi-pot VLF)

H.V.D.I. HVA34TD (VLF/DC Potential Test with Tan Delta Testing)

Megger BITE 2 (Battery Impedance)

Megger DLRO200-115 (Low Resistance Ohmmeter)

Megger MTO330A (Transformer Ohmmeter)

Megger SMRT46 (Relay Test Set)

MAC-TS4 (Vacuum Breaker Tester)

Fluke ii910 and ii915 (Precision Acoustic Imager)

Fluke 805 FC (Vibration Monitor)

Fluke 805 ES Cable (External Sensor for Fluke 805 FC)

Megger MTR105 (Handheld Multifunction Motor/Generator Tester)

Megger DELTA4310A (Power Factor Tester)

Megger PFL22M1500 (Buried Cable Tester, Fault Prelocator)

Megger Smart Thump ST16-20 (Buried Cable Tester, Fault Prelocator)

Megger STX40 (Buried Cable Tester, Fault Prelocator)

Megger digiPHONE+2 (Buried Cable Tracer, Fault Locator)

Hubbell / CAT NO CC403-3178 (Wet/Dry Hot Stick Tester)

Hastings 7707 (Wet/Dry Hot Stick Tester)

Chance T403-3228 (AC Voltage Detector)

Salisbury 4667 (AC Voltage Detector)

Salisbury 4744 (AC Voltage Detector)

Mitchell Ind. 213112 (AC Voltage Detector)

High Voltage Inc / TPFT-5010 (High Voltage AC power supplies) “onsite calibration”

High Voltage Inc / TPTS-100-HAN (High Voltage AC power supplies) “onsite calibration”

The VON CORPORATION / Model C-1 (Portable DC Tester) “onsite calibration”

4.1. The Contractor will also make the necessary repairs to equipment as needed. Repair costs will be charged to the original contract from a separate CLIN specifically meant for repair quotes and costs.

4.2. Calibration Standards: All equipment will be calibrated in accordance with the manufacturer’s specifications, using reference standards whose accuracies are traceable to ISO/IEC 17025 and ANSI/NCSLI Z540-1.

4.3. Documentation: A signed certificate of calibration will be provided for each piece of equipment calibrated, showing the nomenclature, manufacturer, model number, equipment serial number, date calibrated, and date of next calibration. Calibration data will also be provided along with the certificate for each calibrated item, detailing all test readings recorded.

4.3.1. Geographic Flexibility, Onsite Calibration: The Contractor must be able to provide onsite calibration service for Fort Belvoir, VA, and Fort Bragg, NC.

4.3.2. Geographic Flexibility, Mobile Pickup and Delivery: As an alternative to

Section 3.3.1, or in conjunction with Section 3.3.1, the Contractor must be able to drive to our area of operations (Fort Belvoir, VA; and Fort Bragg, NC), pick up the equipment to be calibrated and/or repaired, transport the equipment to the Contractor’s calibration facility, calibrate and/or repair the equipment, then transport the equipment back to its respective location (in a fully calibrated and/or repaired status). The Government is not responsible for supplying additional funding following the award of this contract, concerning internal Contractor shipping costs, while the Contractor is in possession of Government property.

4.3.3. Geographic Flexibility. Government drop off and pickup: As an alternative to Section 3.3.1, or in conjunction with Section 3.3.1, the Government must be able to drive to the Contractor’s area of operations to drop off the equipment to be calibrated and/or repaired, then pick up the equipment (in a fully calibrated and/or repaired status) from the Contractor’s area of operations.

4.3.4. Temporal Flexibility. The Contractor should perform calibration on TMDE items upon request that are currently within their calibration interval when operational requirements - such as OCONUS exercises and unit deployments - necessitate an extended period during which calibration cannot reasonably be performed.

4.4. Timeline for Calibration. The Contractor shall ensure all TMDE requiring calibration are calibrated and returned to the unit no later than the established calibration due date, as provided by the Government. This requirement is contingent upon the unit providing the TMDDE and notification of service requirement at least 14 calendar days prior to the calibration due date. Failure by the Government to provide the required 14 calendar day notice relieves the Contractor of responsibility for meeting the calibration due date. However, the Contractor should make every reasonable effort to complete the calibration at the earliest practicable date.

4.5. No later than 1700 hours EST every Thursday, the Contractor provides a status report for all 249th EN BN equipment in the Contractor’s possession. This status report will include, per serialized item: date of receipt, current calibration status, expected return date, and pertinent issues. Exact status report format will be discussed during the post-award kick-off meeting described in Section 6.2.

4.6. Out of Scope Repairs. If the equipment sent for calibration needs repair beyond calibration standards outlined by the manufacturer and this contract, a cost estimate for the repair will be provided to the 249th Engineer Battalion POC. This cost estimate will include at a minimum: the individual deficiencies, itemized quote for repair costs, and estimated time needed to conduct such repairs if requiring more than the 14 calendar days as outlined in Section 3.4. The Contractor may not begin such repairs until given written permission by the POC. The POC will determine, on a case-by-case basis, whether to fund the repair. If the POC decides against funding the repair, the Contractor will ship the equipment back to its appropriate location. If the POC decides to fund the repair, the POC will communicate this to the Contracting Officer (KO) who will amend the contract as needed. Subsequently, additional funds will be issued to the Contractor in order to execute repair(s), and the Contractor will be notified by the POC to begin work. The Government is not responsible for any out of scope repairs conducted by the Contractor without prior written approval.

5. Period of Performance. The period of performance for this contract begins on the effective date of award and lasts for one year, with one additional option year. If the Period of Performance expires while the Contractor is still in possession of 249th EN BN TMDE, then the Contractor will calibrate the items in their possession and return these items back to the 249th EN BN, at no additional cost to the Government.

6. Options.

6.1. The Government reserves the right to extend the terms of this contract at the prices set forth, in accordance with the terms and conditions contained in clause 52.217-9 entitled “Option to extend the terms of the contact,” for one additional year-long period.

6.2. The Government reserves the right to add or delete certain TMDE items detailed in Section 3 of this contract. If items are to be added or deleted to the contractual scope, both the Contractor and Government will agree to new pricing and terms per item.

7. Contractor Responsibilities.

7.1. The Contractor will furnish all equipment and personnel to meet the specifications of this contract.

7.2. The Contractor agrees to attend, a post-award kick-off meeting convened by the 249th EN BN to discuss reporting requirements and project documentation. The KO, and other Government personnel as appropriate, may meet periodically with the Contractor to review the Contractor's performance. At these meetings, the KO will apprise the Contractor of how the Government views the Contractor's performance, and the Contractor will apprise the Government of problems, if any, being experienced. Appropriate action shall be taken to resolve outstanding issues. These meetings shall be at no additional cost to the Government.

7.3. The Contractor shall provide a contract manager who shall be responsible for the performance of the work. The name of this person, and an alternate, shall be designated in writing. The contract manager, or alternate, shall have full authority to act for the Contractor on all contract matters relating to daily operation of this contract.

8. Delivery Schedule.

8.1. The Government will notify the Contractor, in writing, prior to the transfer of equipment to the calibration site, and coordinate a pick-up date. The written notification will outline the return location of the equipment, model number(s), serial number(s), appropriate POC(s), and an itemized report on the condition of the equipment.

8.2. Within three working days of receiving the equipment, the Contractor will provide, in writing, any discrepancies to the itemized equipment conditions report. If the Contractor receives the equipment in conditions other than described in such report, the Contractor must refute the report, citing specific reasons, such as a cracked screen not previously annotated by the report.

9. Unit Addresses.

9.1. B Company, 249th Engineer Battalion

Building 3-2631 Butner Road Fort Bragg, NC 28310

9.2. C Company, 249th Engineer Battalion

9450 Jackson Loop, Building 1416 Fort Belvoir, VA 22060

9.3. HHC, 249th Engineer Battalion

9450 Jackson Loop, Building 1418 Fort Belvoir, VA 22060

10. Contractor Manpower Reporting.

10.1. The Contractor shall report all Contractor and Sub-Contractor labor hours required for performance of services under this contract via a secured data collection site. The Contractor is required to completely fill in all required data fields using the following web address: https://www.ecmra.mil/Default.aspx

10.2. Reporting inputs will be for the labor executed during the period of performance. While inputs may be reported at any time during the FY, all data shall be reported no later than the end of the period of performance. Contractors may direct questions to the help desk at https://www.ecmra.mil/Default.aspx

11. Security Requirements.

11.1. Physical Security. The Contractor shall be responsible for safeguarding all Government equipment, information, and property provided for Contractor use IAW AR 190-13, The Army Physical Security Program. At the close of each work period, Government facilities, equipment, and materials shall be secured.

11.2. The Contractor must pre-screen Candidates using the E-Verify Program

(http://www.uscis.gov/e-verify) website to meet the established employment eligibility requirements. The Vendor must ensure that the Candidate has two valid forms of Government issued identification prior to enrollment to ensure the correct information is entered into the E-Verify system. An initial list of verified/eligible Candidates must be provided to the Contract Officer’s Representative (COR) no later than 3 business days after the initial contract award.

11.3. Security of Classified Items, Systems and Information. The Contractor, as a general rule, shall not have access to classified information; however, should classified documents fall into the possession of the Contractor, the Contractor shall immediately contact the COR for disposition instructions.

12. The point of contact for this memorandum is the undersigned at 571-265-5848 or eddie.b.jones.mil@army.mil.

EDDIE B. JONES III

1LT, EN

Assistant Battalion Logistics Officer https://www.ecmra.mil/Default.aspx https://www.ecmra.mil/Default.aspx http://www.uscis.gov/e-verify)