MPEX-00-ENG-002-A2.pdf

PDF 397 KB Posted

Attached to
Target Service Shield Machining and Welding
Solicitation number
PR444575
Issued by

About this file

This is a technical specification document providing detailed definitions for knife edge (Conflat®) flanges used on the Material Plasma Exposure Experiment (MPEX) project managed by Oak Ridge National Laboratory for the U.S. Department of Energy under contract DE-AC05-00OR22725.

The document establishes acceptable dimensional standards for two classifications of knife edge flanges: Stainless Steel Flanges and Glidcop AL-15 (UNS C15715) / CuCrZr (UNS C18150) Copper Alloy Flanges. Overall flange dimensions must comply with ASTM E2734/E2734M standard for Dimensions of Knife Edge Flanges, including gasket dimensions specified in Figure 3 of that standard. Stainless steel knife edges must conform to Figure 2 of ASTM E2734/E2734M. Copper alloy knife edges are defined by the detail specifications in Figure 1, where dimension F references the knife edge radius from ASTM E2734/E2734M Table 1, dimensioned to the center mark of the R.006 dimension. All knife edge vacuum flanges must include at minimum two opposing vent grooves for leak checking purposes. The preferred orientation positions grooves vertically with one pointing downward and the other upward, though alternative orientations may be accommodated if vertical positioning prevents access for leak checking. The vent grooves are dimensioned per Figure 2 with R.030 on both sides. This specification was approved on September 26, 2022 and is Revision 1, which refined the copper alloy definition and added leak check port requirements.

View the file

Other files

On GovTribe

Work with this file

  • Download the original file
  • Contacts named in this file
  • Similar government files
  • Ask GovTribe AI about this file

Text version

MPEX-00-ENG-002-A2-R01 Appendix 2 Page 1 of 5

Knife Edge Flange Definition

Vacuum Handbook Appendix 2: Knife Edge Flange

Definition

MPEX-00-ENG-002-A2

MATERIAL PLASMA EXPOSURE EXPERIMENT

(MPEX)

Prepared by

OAK RIDGE NATIONAL LABORATORY

Oak Ridge, TN 37831-6283

Managed by

UT-BATTELLE, LLC

For the

US DEPARTMENT OF ENERGY

under contract DE-AC05-00OR22725

September 2022

This report was prepared as an account of work sponsored by an agency of the

United States government. Neither the United States government nor any agency thereof, nor any of their employees, makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed, or represents that its use would not infringe privately owned rights. Reference herein to any specific commercial product, process, or service by trade name, trademark, manufacturer, or otherwise, does not necessarily constitute or imply its endorsement, recommendation, or favoring by the United States government or any agency thereof. The views and opinions of authors expressed herein do not necessarily state or reflect those of the United States government or any agency thereof.

MPEX-00-ENG-002-A2-R01 Appendix 2 Page 2 of 5

Vacuum Handbook Appendix 2: Knife Edge Flange Definition for the

Material Plasma Exposure Experiment Project

MPEX-00-ENG-002-A2

Authors(s):

Adam M. Aaron, Vacuum Systems CAM Date

Reviewer(s):

Jeff Ulreich, Vacuum SME Date

Approver(s):

Aftab Hussain, MPEX Lead Engineer Date

MPEX-00-ENG-002-A2-R01 Appendix 2 Page 3 of 5

Vacuum Handbook Appendix 2: Knife Edge Flange Definition for the

Material Plasma Exposure Experiment Project

MPEX-00-ENG-002-A2

Change Log

Revision History

Revision Date Description of Changes

0 2022-09-08 Initial issue

1 2022-09-23 Minor document re-structuring with headers.

Refined Copper Alloy knife edge definition including removal of reference [2] as it is no longer applicable.

Added detail on leak check port as required for all knife edge flanges.

MPEX-00-ENG-002-A2-R01 Appendix 2 Page 4 of 5

The purpose of this appendix is to define the acceptable dimensions for knife edge (aka Conflat ®) flanges on the MPEX project. The definitions are broken into two classifications, Stainless Steel Flanges and Glidcop AL-15 (UNS C15715) / CuCrZr (UNS C18150) Flanges. These two definitions differ only in the detail of the knife edge itself, not in the overall flange dimensions. There is also a requirement for leak check ports specified.

Overall flange dimensions shall be in accordance with ASTM E2734/E2734M - Dimensions of Knife

Edge Flanges [1]. This includes the gasket dimensions as defined in FIG 3 of the standard.

A2-1 Knife Edge Definition

All Stainless-Steel knife edge detail shall comply with ASTM E2734/E2734M - Dimensions of Knife

Edge Flanges [1], FIG 2 of standard.

All Glidcop AL-15 and CuCrZr shall be defined by the knife-edge detail in Figure 1 where dimension F refers to the knife edge radius from ASTM E2734/E2734M: TABLE 1 of standard, dimensioned to the center mark of the R.006 dimension.

Figure 1. Knife-Edge Detail for Copper Alloy Components

A2-2 Vent Grooves for Leak Checking

The preferred implementation of the vent grooves is shown in Figure 2.

All knife edge vacuum flanges shall have at minimum two opposing vent grooves.

MPEX-00-ENG-002-A2-R01 Appendix 2 Page 5 of 5

The preferred orientation in assembly for the vent grooves is vertical, with one groove pointing downward and the other upward. This preference might not allow access for leak checking, in which case the orientation of the grooves may be changed to accommodate.

Figure 2. Preferred Dimensioning for Vent Grooves for leak checking

References

[1] ASTM Standard E2734/E2734M, 2018, “Standard Specification for Dimensions of

Knife-Edge Flanges,” ASTM International, West Conshohocken, PA, 2018, DOI:

10.1520/E2734_E2734M-10R18

2022-09-23T14:32:53-0400
Adam M. Aaron
2022-09-23T14:53:45-0400
Jeffrey Ulreich
2022-09-26T14:28:53-0400
Aftab Hussain

File details come from the government source that posted it. Updated .