Part DSCRJHTB991102 Description 2026 02 12.pdf
PDF 93 KB Posted
- Attached to
- Request for Information for Pipe Bending Machine
- Solicitation number
- 47QACA26RFI0002
- Issued by
- Not on record
About this file
This is a specifications document for a pipe bending machine procurement by the United States Air Force (USAF) for Robins Air Force Base, Georgia. The document specifies technical requirements for a manual, self-contained, floor-mounted hydraulic pipe bending machine with a part number of DSCRJHTB991102. The machine must have a capacity of 1.5 inch outer diameter (OD), center line radius of 8 inches maximum, maximum bend arm movement of 195 degrees, and accommodate maximum over-mandrel tube lengths of 10 feet. The machine must operate in both clockwise and counter-clockwise directions and feature a hydraulic foot-operated manual extractor with no external power source requirement.
The procurement specifies comprehensive tooling requirements including 25 bend dies (0.375 to 1.5 inches), 6 mandrel rods, 9 clamp dies, 9 pressure dies, a mandrel extractor system, and an angle bend indicator assembly. Vendors must provide two hard copies and one electronic copy of technical documentation to Bob Diamond, Equipment Specialist, at Robins AFB (235 Byron Street, Building 300, Suite 19A, Robins AFB, GA 31098-1813). The machine must fit through a 12-foot-wide doorway. This will be an open competitive procurement with source selection determined after vendor quotes and technical acceptability review. The USAF notes that installation, training, tooling, and non-standard package options are excluded from this procurement. PHI Hydraulics of City of Industry, California is identified as a known potential source.
View the file
Other files
| File | Type | Posted |
|---|---|---|
| RFI 2026 02 12.pdf | ||
| Delivery Locations Pipe Bending Machine 2026 02 12.pdf |
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
P/N#: DSCRJHTB991102
Item Noun: pipe bending machine
Specifications/Technical Characteristics:
• Manual bending machine
• Self-contained (no outside power source)
• Floor mounted
• Hydraulic foot operated manual extractor
• Direction of bend: clockwise and couter-clockwise
• Capacity 1.5 in OD
• Center line radius 8 in max
• Maximum bend arm movement 195°
• Maximum over-mandrel tube length 10 ft
• Tooling: (see attached tooling sheet for exact specifications for tooling requried) o
25 Bend Die 0.375 to 1.5 in (see attached tooling sheet) o 6 mandrel rods o 9 clamp die 0.375 to 1.5 in o 9 pressure die 0.375 to 1.5 in o Mandel extractor system o Angle bend indicator assembly
• Two (2) hard copies and one (1) electronic copy of technical data shall be provided with the machine.
• Shipping address for electronic technical data packages is:
Attn: Bob Diamond, Equip. Specialist 235 Byron Street, (Bldg. 300) Suite 19A Robins AFB, GA 31098-1813
If not specified within the characteristics of the NSN, please provide the following information:
• The existing source power available at the facility is o Volt: __ N/A______ o Phase: __N/A____ __ o Frequency: __N/A_______ Hertz (Hz)
• The machine must fit through a doorway with the following dimensions:
o Width: ___12’ FT______ o Height: ___ ______
• Available floor space for equipment width by length to include required operator workspace and OSHA required access clearances to service panels.
o Width: ___ o Length: _
• If available, a known source for the equipment is _____PHI Hydraulics, City of Industry, CA__
Note 1: This will be an open competitive competition and the source of supply will not be determined until the vendor quotes and technical acceptability is reviewed by the contracting agency.
Note 2: We the USAF do not include installation, training, tooling or any additional options that are not part of the standard package in the above characteristics data.
File details come from the government source that posted it. Updated .